Cable indications for - Ramcro · Cable indications for ... On condition the cable gland is not certified as part of the equipment but tested and certified as ... 0.50 sqmm 37.20

www.ramcro.it

Cable indications for RAMCROIL VAP-GAS BARRIER

Fully Filled in according to IEC 60079-14This standard contains specific requirements for the design, selection, installation and initial verifica-tion of electrical installations in, or associated with, places where explosive atmospheres.When the equipment must also be suitable for other critical environmental conditions, for example the possibility of entry of water and possibility of corrosion, can be necessary requirements additional protection.The requirements set by the standard apply only in the case of use of the equipment in standard atmospheric conditions, as defined by the IEC EN 60079-0; in the case of different weather conditions it may take additional precautions.This standard replaces the IEC 60079-14: 2010-02 which remains applicable until 02/01/2017 and constitutes a technical revision.

The indications about the cable must be as the follow:

1. The cable entry system - Shall comply with the IEC 60079-1 indications

a) Cable entry device in compliance with IEC 79-1 “Construction and verification test of flameproof enclosures of electrical apparatus” and particular type of cable intended for use with that device.On condition the cable gland is not certified as part of the equipment but tested and certified as a separate component and the used cable is substantially compact and circular the selection chart above taken from section 10 of EN/ IEC60079-1 can be used.

2. Cable Construction - Should be Round

In order to comply with IEC installation standards,cable glands using elastomeric sealing rings as ameans of maintaining the Flameproof protectionmethod can only be used if the cable selected is :

“Substantially compact and circular with an extruded bedding, and if any fillers are used they are Non-Hygroscopic”This is clearly not always the case with cables used in hazardous areas.But the cable must play a part in the safety of the installation, even in the case of indirect cable entry, when gas migration must be avoided.e.g., where cables run across two zones, or indeed from a hazardous area into a safe area.

3. Sample IEC Cable Configurations

Which type is suitable for use with Flameproof Ex d equipment when a cable gland with an elasto-meric sealing ring would be considered?b) thermoset, thermosetting or elastomeric cable which is substantially compact and circular, has extruded bedding and fillers, if any, are non-hygroscopic, may utilize flameproof cable entry devices, incorporating a sealing ring selected in accordance with figure 1,

www.ramcro.it

EN50288

IEC60079-14

www.ramcro.it

Cable A is not suitable to apply a Flameproof sealing ring as this cable is the incorrect shape, and un-less the cable is round the sealing ring will not be able to make an effective seal on the cable.

Cables B, D & E are not suitable to apply a Flameproof sealing ring, as the white areas represent a gap or void in the cable whereby there is either no inner cable sheath, or extruded bedding, or suit-able fillers are absent. In this case no protection to the interstices of the cable can be offered by a sealing ring.

Cable C is the only one of the five sample cables illustrated which could be selected as correctly meeting the IEC 60079-14 criteria, as it has an extruded inner cable bedding and there is no gas migration path between the conductors.

Equally, if the cable is not adequately filled, and allows the passage of air or gas to flow along the cable length then there would be no protection to the inner part of the cable when an elastomeric sealing ring is used.

In this case a compound barrier type cable gland is the only safe solution and this is needed to maintain the integrity of the equipment as explained above, and prevent gas migration from equip-ment to equipment, or hazardous areas to safe areas.Now a new addition to the Annex E inside the IEC/EN 60079-14, provides a test method that can confirm the appropriateness of the combination cable with strain relief with sealing ring. This appen-dix describes theverification process cables for tightness to prevent “leakage” of gases between the cores and the eventual transfer of the flame blast through cable.The test is carried out on a sample of cable length 0.5 m that attaches to a completely closed and sealedhousing volume 5 l (± 2 liters), under conditions of stable ambient temperature. It is believed that the particular patternsatisfied if the initial pressure of 0.3 kPa within housing is reduced by less than 0.15 kPa within 5 s.The housing must be sealed effectively to reduce pressure losses through the casing bands.

Ex-Agency provided a laboratory for the described test method and has already conducted several tests for the endUsers.

EN50

288

IEC

6007

9-14Cable indications for

RAMCROIL VAP-GAS BARRIERFully Filled in according to IEC 60079-14

Laboratory testing Ex ‘d’ entries with sealing ring and cable Ex-Area according to Appendix E of the fifth edition of IEC 60079-14.

www.ramcro.it

EN50288

IEC60079-14

Prepared by RAMCRO LAB 26/08/2015

RAMCRO S.P.A. Test Evaluation

Test on sample: Ramfirecro-F3 2x2.50 mm2 cable to LPCB 568a

Test No. 288/12

IEC / EN 60079-14

Test Evaluation on Ramfirecro-F3 2x2.50 mm2 cable to LPCB 568a - Test No. 288/12 26/8/2015

Via Marzorati, 15 - 20014 Nerviano - Milano Tel. +39 0331 406 511 + 50 lines / FAX +39 0331 406 559 + 5 lines / www.ramcro.it

7

IEC / EN 60079-14

Test date: 24/08/2015

Results

Cable Type Test Test Time AIR pressure Test

Comments Results

2 x 2.50 mm2 1 5 seconds 0.3 kPa No comments 0.05 kPa 2 5 seconds 0.3 kPa No comments 0.04 kPa

Conclusions

The samples specified on page 5 of this document, met the requirements of IEC / EN 60079-14

Test date: 24/08/2015 Operator Giusto Simone

Cable indications for RAMCROIL VAP-GAS BARRIER

Fully Filled in according to IEC 60079-14

www.ramcro.it

EN50

288

IEC

6007

9-14

EN 50288-7 - IEC 60079-14 (VAP-GAS BARRIER Cables)M u l t i p a i r P V C / P E / X L P E / L S Z H I n s u l a t e d , I n s t r u m e n t a t i o n C o n t r o l C a b l e 9 0 V - 3 0 0 V - 5 0 0 VCollective Screen, Unarmoured - Individual and Collective Screen, Unarmoured

ApplicationsThese cables are designed to connect electrical instrument circuits and provide communication services in and around process plant (e.g. petrochemical industry etc.).Not suitable for direct buried application

StandardsReferences- IEC 60079-14- EN 50288-1- EN 50288-7- HD 383- EN 50290-2- IEC 60332-1- IEC 60332-3-24

CAM

IAM

/ C

AM

RamcroPart NoCollective screened

No. of Pairs/Triple

Cond.mm²

90 VO/Dmm

300 VO/Dmm

500 VO/Dmm

MAS0150HDADN-RE 1P 0.50 4.4 4.7 5.4

MAS0250HDADN-RE 2P (Q) 0.50 5.0 5.3 6.2

MAS0550HDADN-RE 5P 0.50 8.0 8.6 10.4

MAS1050HDADN-RE 10P 0.50 10.0 12.0 14.7

MAS1550HDADN-RE 15P 0.50 12.8 13.9 17.0

MAS2050HDADN-RE 20P 0.50 14.4 15.6 19.2

MAS3750HDADX-RE 1T 0.50 4.6 4.9 5.7

MAS0175HDADN-RE 1P 0.75 4.8 5.0 5.8

MAS0275HDADN-RE 2P (Q) 0.75 5.4 5.7 6.7

MAS0575HDADN-RE 5P 0.75 8.9 9.5 11.2

MAS1075HDADN-RE 10P 0.75 12.4 13.2 15.9

MAS1575HDADN-RE 15P 0.75 14.2 15.3 18.4

MAS2075HDADN-RE 20P 0.75 16.0 17.2 20.8

MAS3775HDADX-RE 1T 0.75 5.0 5.3 6.1

MAS0110HDADN-RE 1P 1.00 5.4 5.4 5.8

MAS0210HDADN-RE 2P (Q) 1.00 6.2 6.2 6.7

MAS0510HDADN-RE 5P 1.00 10.4 10.4 11.2

MAS1010HDADN-RE 10P 1.00 14.7 14.7 15.9

MAS1510HDADN-RE 15P 1.00 17.0 17.0 18.4

MAS2010HDADN-RE 20P 1.00 19.2 19.2 20.8

MAS3710HDADX-RE 1T 1.00 5.7 5.7 6.1

MAS0115HDADN-RE 1P 1.50 6.1 6.3 6.9

MAS0215HDADN-RE 2P (Q) 1.50 7.0 7.2 8.0

MAS0515HDADN-RE 5P 1.50 11.8 12.3 13.7

MAS1015HDADN-RE 10P 1.50 16.8 17.4 19.5

MAS1515HDADN-RE 15P 1.50 19.4 20.2 22.6

MAS2015HDADN-RE 20P 1.50 22.0 22.9 25.6

MAS3715HDADX-RE 1T 1.50 6.4 6.6 7.3

MAS0125HDADN-RE 1P 2.50 / / 8.1

MAS0225HDADN-RE 2P (Q) 2.50 / / 9.5

MAS0525HDADN-RE 5P 2.50 / / 16.6

MAS1025HDADN-RE 10P 2.50 / / 23.9

MAS1525HDADN-RE 15P 2.50 / / 27.7

MAS2025HDADN-RE 20P 2.50 / / 31.5

MAS3725HDADX-RE 1T 2.50 / / 8.7

RamcroPart NoInd & Collective screened

No. of Pairs/Triple

Cond.mm²

90 VO/Dmm

300 VO/Dmm

500 VO/Dmm

MAC0250HDADN-RE 2P 0.50 7.0 7.4 8.8

MAC0350HDADN-RE 3P 0.50 7.4 7.9 9.4

MAC0550HDADN-RE 5P 0.50 8.8 9.5 11.4

MAC1050HDADN-RE 10P 0.50 12.3 13.3 16.1

MAC1550HDADN-RE 15P 0.50 14.2 15.3 18.6

MAC2050HDADN-RE 20P 0.50 16.0 17.3 21.0

MAC3050HDADN-RE 30P 0.50 18.9 20.4 24.8

MAC0275HDADN-RE 2P 0.75 7.6 8.1 9.5

MAC0375HDADN-RE 3P 0.75 8.1 8.6 10.1

MAC0575HDADN-RE 5P 0.75 9.7 10.3 12.2

MAC1075HDADN-RE 10P 0.75 13.6 14.6 17.4

MAC1575HDADN-RE 15P 0.75 15.7 16.8 20.1

MAC2075HDADN-RE 20P 0.75 17.7 19.0 22.8

MAC3075HDADN-RE 30P 0.75 20.9 22.4 26.9

MAC0210HDADN-RE 2P 1.00 8.8 8.8 10.2

MAC0310HDADN-RE 3P 1.00 9.4 9.4 10.9

MAC0510HDADN-RE 5P 1.00 11.4 11.4 13.3

MAC1010HDADN-RE 10P 1.00 16.1 16.1 18.9

MAC1510HDADN-RE 15P 1.00 18.6 18.6 21.9

MAC2010HDADN-RE 20P 1.00 21.0 21.0 24.8

MAC3010HDADN-RE 30P 1.00 24.8 24.8 29.3

MAC0215HDADN-RE 2P 1.50 9.9 10.3 11.4

MAC0315HDADN-RE 3P 1.50 10.6 11.0 12.1

MAC0515HDADN-RE 5P 1.50 12.9 13.3 14.8

MAC1015HDADN-RE 10P 1.50 18.3 19.0 21.2

MAC1515HDADN-RE 15P 1.50 21.2 22.0 24.6

MAC2015HDADN-RE 20P 1.50 24.0 25.0 27.9

MAC3015HDADN-RE 30P 1.50 28.4 29.5 33.0

MAC0225HDADN-RE 2P 2.50 / / 13.7

MAC0325HDADN-RE 3P 2.50 / / 14.6

MAC0525HDADN-RE 5P 2.50 / / 17.9

MAC1025HDADN-RE 10P 2.50 / / 25.8

MAC1525HDADN-RE 15P 2.50 / / 30.0

MAC2025HDADN-RE 20P 2.50 / / 34.1

MAC3025HDADN-RE 30P 2.50 / / 40.4

Technical DataMaximum conductor d.c. resistance:

Minimuminsulation resistance:

Maximum Mutual Capacitance:

Maximum L/R Ratio:

Voltage Rating:

Operating Temperature:

Installation Temperature:

Conductor size Оhm/km at +20°C class 1 class 2 class 50.50 sqmm 37.20 36.36 39.390.75 sqmm 24.80 24.80 26.801.00 sqmm 18.60 18.30 19.701.50 sqmm 12.30 12.42 13.432.50 sqmm 7.48 7.56 8.05

PVC: >10 MОhm x km at +20°CPE: >1 GОhm x km at +20°CXLPE: >1 GОhm x km at +20°CLSZH: >10 MОhm x km at +20°C

PVC: 250 pF/mPE: 150 pF/mXLPE: 150 pF/mLSZH: 250 pF/m

0.50 sqmm, 0.75 sqmm, 1.00 sqmm: 25 µH/Ω1.50 sqmm: 40 µH/Ω2.50 sqmm: 65 µH/Ω

90 V - 300 V - 500 V

PVC: + 75° C, + 90° C, + 105° CPE: + 75° CXLPE: + 90° CLSZH: + 75° C

Min. +5° C / MAX + 50° C

Construction - Conductors: Solid (Class1),Stranded (Class 2) or Flexible (Class5) copper conductor to HD383

- Insulation: PVC, PE, XLPE, LSZH to EN 50290-2

- 100 mm maximum pair length

- Individual and collective Screen or - Collective Screen Polyster tape 50% overlap Aluminium/Polyester tape, metallic side down, in contact with Tinned Copper drain wire

- Outer Sheath: PVC, LSZH to EN 50290-2

- Color: Black or Blue

- Conductor Color Code: a) White and Black numbered b) on agreement with the customer, Blue and Black numbered

Hazardous AreaClassificationIEC Zone 1 - Group 2

www.ramcro.it

EN 50288-7 - IEC 60079-14 (VAP-GAS BARRIER Cables)M u l t i p a i r P V C / P E / X L P E / L S Z H I n s u l a t e d , I n s t r u m e n t a t i o n C o n t r o l C a b l e 9 0 V - 3 0 0 V - 5 0 0 VCollective Screen, Armoured - Individual and Collective Screen, Armoured

ApplicationsThese cables are designed to connect electrical instrument circuits and provide communication services in and around process plant (e.g. petrochemical industry etc.). Suitable for direct buried application.


CAM

/ S

WA

IAM

/ C

AM /

SW

A


No. of Pairs/Triple

Cond.mm²

90 VO/Dmm

300 VO/Dmm

500 VO/Dmm

MAS0150ADADN-RE 1P 0.50 8.7 9.0 9.8

MAS0250ADADN-RE 2P (Q) 0.50 9.3 9.6 10.6

MAS0550ADADN-RE 5P 0.50 12.5 13.1 15.0

MAS1050ADADN-RE 10P 0.50 15.8 16.7 19.5

MAS1550ADADN-RE 15P 0.50 17.5 18.6 22.6

MAS2050ADADN-RE 20P 0.50 19.2 21.2 25.0

MAS3750ADADN-RE 1T 0.50 8.9 9.2 10.1

MAS0175ADADN-RE 1P 0.75 9.1 9.3 10.1

MAS0275ADADN-RE 2P (Q) 0.75 9.7 10.1 11.1

MAS0575ADADN-RE 5P 0.75 13.4 14.0 15.9

MAS1075ADADN-RE 10P 0.75 17.1 18.0 21.5

MAS1575ADADN-RE 15P 0.75 19.0 20.9 24.1

MAS2075ADADN-RE 20P 0.75 21.7 22.9 26.7

MAS3775ADADN-RE 1T 0.75 9.3 9.6 10.5

MAS0110ADADN-RE 1P 1.00 9.8 9.8 10.6

MAS0210ADADN-RE 2P (Q) 1.00 10.6 10.6 11.6

MAS0510ADADN-RE 5P 1.00 15.0 15.5 16.9

MAS1010ADADN-RE 10P 1.00 19.5 20.9 23.0

MAS1510ADADN-RE 15P 1.00 22.6 23.5 25.9

MAS2010ADADN-RE 20P 1.00 25.0 25.9 28.7

MAS3710ADADN-RE 1T 1.00 10.1 10.3 11.0

MAS0115ADADN-RE 1P 1.50 10.4 10.6 11.3

MAS0215ADADN-RE 2P (Q) 1.50 11.4 14.1 12.4

MAS0515ADADN-RE 5P 1.50 16.5 17.0 18.4

MAS1015ADADN-RE 10P 1.50 22.4 23.1 25.3

MAS1515ADADN-RE 15P 1.50 25.2 26.1 28.6

MAS2015ADADN-RE 20P 1.50 27.9 28.9 32.4

MAS3715ADADN-RE 1T 1.50 10.8 11.0 11.7

MAS0125ADADN-RE 1P 2.50 / / 12.6

MAS0225ADADN-RE 2P (Q) 2.50 / / 14.0

MAS0525ADADN-RE 5P 2.50 / / 22.3

MAS1025ADADN-RE 10P 2.50 / / 29.9

MAS1525ADADN-RE 15P 2.50 / / 34.6

MAS2025ADADN-RE 20P 2.50 / / 38.6

MAS3725ADADN-RE 1T 2.50 / / 13.1


No. of Pairs/Triple

Cond.mm²

90 VO/Dmm

300 VO/Dmm

500 VO/Dmm

MAC0250ADADN-RE 2P 0.50 11.4 11.9 13.4

MAC0350ADADN-RE 3P 0.50 11.8 12.4 13.9

MAC0550ADADN-RE 5P 0.50 13.4 14.0 16.0

MAC1050ADADN-RE 10P 0.50 17.1 18.1 21.7

MAC1550ADADN-RE 15P 0.50 19.1 20.9 24.4

MAC2050ADADN-RE 20P 0.50 21.7 23.0 27.0

MAC3050ADADN-RE 30P 0.50 24.7 26.2 31.0

MAC0275ADADX-RE 2P 0.75 12.1 12.6 14.0

MAC0375ADADX-RE 3P 0.75 12.6 13.1 14.7

MAC0575ADADN-RE 5P 0.75 14.3 15.0 16.9

MAC1075ADADN-RE 10P 0.75 18.4 19.4 23.1

MAC1575ADADN-RE 15P 0.75 21.4 22.5 26.0

MAC2075ADADN-RE 20P 0.75 23.5 24.8 28.8

MAC3075ADADN-RE 30P 0.75 26.8 28.4 33.8

MAC0210ADADN-RE 2P 1.00 13.4 13.4 14.8

MAC0310ADADN-RE 3P 1.00 13.9 13.9 15.5

MAC0510ADADN-RE 5P 1.00 16.0 16.0 18.0

MAC1010ADADN-RE 10P 1.00 21.7 21.7 24.7

MAC1510ADADN-RE 15P 1.00 24.4 24.4 27.9

MAC2010ADADN-RE 20P 1.00 27.0 27.0 30.9

MAC3010ADADN-RE 30P 1.00 31.0 31.0 34.3

MAC0215ADADN-RE 2P 1.50 14.5 14.9 16.0

MAC0315ADADN-RE 3P 1.50 15.2 15.6 16.8

MAC0515ADADN-RE 5P 1.50 17.6 18.1 19.7

MAC1015ADADN-RE 10P 1.50 24.1 24.8 27.1

MAC1515ADADN-RE 15P 1.50 27.2 28.0 30.7

MAC2015ADADN-RE 20P 1.50 30.1 31.1 34.8

MAC3015ADADN-RE 30P 1.50 35.4 36.5 40.2

MAC0225ADADN-RE 2P 2.50 / / 18.5

MAC0325ADADN-RE 3P 2.50 / / 19.5

MAC0525ADADN-RE 5P 2.50 / / 23.7

MAC1025ADADN-RE 10P 2.50 / / 32.6

MAC1525ADADN-RE 15P 2.50 / / 37.1

MAC2025ADADN-RE 20P 2.50 / / 41.4

MAC3025ADADN-RE 30P 2.50 / / 48.9




Maximum L/R Ratio:

Voltage Rating:







90 V - 300 V - 500 V


Min. +5° C / MAX + 50° C





- Inner Sheath: PVC, LSZH to EN 50290-2 - Armouring: Galvanized Steel Wires





EN50288

IEC60079-14

3

www.ramcro.it

EN 50288-7 - IEC 60079-14 (VAP-GAS BARRIER Cables)M u l t i p a i r P V C / P E / X L P E / L S Z H I n s u l a t e d , I n s t r u m e n t a t i o n C o n t r o l C a b l e 9 0 V - 3 0 0 V - 5 0 0 VCollective Screen, Lead and Armour - Individual and Collective Screen, Lead and Armour

ApplicationsThese cables are designed to connect electrical instrument circuits and provide communication services in and around process plant (e.g. petrochemical industry etc.). Suitable for direct buried application.


CAM

/ L

C /

SWA

IAM

/ C

AM /

LC

/ SW

A


No. of Pairs/Triple

Cond.mm²

90 VO/Dmm

300 VO/Dmm

500 VO/Dmm

MAS0150ADADX-RELC 1P 0.50 13.7 14.0 14.8

MAS0250ADADX-RELC 2P (Q) 0.50 14.3 14.7 15.7

MAS0550ADADX-RELC 5P 0.50 17.6 18.2 21.2

MAS1050ADADX-RELC 10P 0.50 22.0 22.9 25.7

MAS1550ADADX-RELC 15P 0.50 23.8 24.8 28.3

MAS2050ADADX-RELC 20P 0.50 25.8 26.9 30.9

MAS3750ADADX-RELC 1T 0.50 14.0 14.3 15.1

MAS0175ADADX-RELC 1P 0.75 14.1 14.4 15.2

MAS0275ADADX-RELC 2P (Q) 0.75 14.8 15.1 16.1

MAS0575ADADX-RELC 5P 0.75 18.4 19.1 22.1

MAS1075ADADX-RELC 10P 0.75 23.3 24.2 27.2

MAS1575ADADX-RELC 15P 0.75 25.3 26.2 30.1

MAS2075ADADX-RELC 20P 0.75 27.4 28.6 33.2

MAS3775ADADX-RELC 1T 0.75 14.4 14.7 15.5

MAS0110ADADX-RELC 1P 1.00 14.8 14.8 15.7

MAS0210ADADX-RELC 2P (Q) 1.00 15.7 17.7 16.7

MAS0510ADADX-RELC 5P 1.00 21.2 21.2 23.1

MAS1010ADADX-RELC 10P 1.00 25.7 25.7 28.7

MAS1510ADADX-RELC 15P 1.00 28.3 28.3 32.4

MAS2010ADADX-RELC 20P 1.00 30.9 30.9 35.9

MAS3710ADADX-RELC 1T 1.00 15.1 15.1 16.0

MAS0115ADADX-RELC 1P 1.50 15.5 15.7 16.3

MAS0215ADADX-RELC 2P (Q) 1.50 16.5 16.7 17.5

MAS0515ADADX-RELC 5P 1.50 24.7 23.2 24.7

MAS1015ADADX-RELC 10P 1.50 28.1 28.8 31.2

MAS1515ADADX-RELC 15P 1.50 31.1 32.6 35.8

MAS2015ADADX-RELC 20P 1.50 34.9 36.0 39.1

MAS3715ADADX-RELC 1T 1.50 15.8 16.1 16.8

MAS0125ADADX-RELC 1P 2.50 / / 17.7

MAS0225ADADX-RELC 2P (Q) 2.50 / / 19.9

MAS0525ADADX-RELC 5P 2.50 / / 28.0

MAS1025ADADX-RELC 10P 2.50 / / 37.1

MAS1525ADADX-RELC 15P 2.50 / / 41.4

MAS2025ADADX-RELC 20P 2.50 / / 46.8

MAS3725ADADX-RELC 1T 2.50 / / 18.2


No. of Pairs/Triple

Cond.mm²

90 VO/Dmm

300 VO/Dmm

500 VO/Dmm

MAC0250ADADX-RELC 2P 0.50 16.5 16.9 18.4

MAC0350ADADX-RELC 3P 0.50 16.9 17.4 19.0

MAC0550ADADX-RELC 5P 0.50 18.4 19.1 22.2

MAC1050ADADX-RELC 10P 0.50 23.3 24.3 27.4

MAC1550ADADX-RELC 15P 0.50 25.3 26.6 30.3

MAC2050ADADX-RELC 20P 0.50 27.4 28.7 33.5

MAC3050ADADX-RELC 30P 0.50 30.6 32.8 38.1

MAC0275ADADX-RELC 2P 0.75 17.1 17.6 19.1

MAC0375ADADX-RELC 3P 0.75 17.6 18.2 20.9

MAC0575ADADX-RELC 5P 0.75 19.4 21.2 23.2

MAC1075ADADX-RELC 10P 0.75 24.6 25.6 28.8

MAC1575ADADX-RELC 15P 0.75 27.1 28.2 32.5

MAC2075ADADX-RELC 20P 0.75 29.4 30.7 36.0

MAC3075ADADX-RELC 30P 0.75 33.4 35.6 40.5

MAC0210ADADX-RELC 2P 1.00 18.4 18.4 21.0

MAC0310ADADX-RELC 3P 1.00 19.0 19.0 21.8

MAC0510ADADX-RELC 5P 1.00 22.2 22.2 24.2

MAC1010ADADX-RELC 10P 1.00 27.4 27.4 30.6

MAC1510ADADX-RELC 15P 1.00 30.3 30.3 34.8

MAC2010ADADX-RELC 20P 1.00 33.5 33.5 38.1

MAC3010ADADX-RELC 30P 1.00 38.1 38.1 44.2

MAC0215ADADX-RELC 2P 1.50 20.1 21.1 22.3

MAC0315ADADX-RELC 3P 1.50 21.4 21.8 23.1

MAC0515ADADX-RELC 5P 1.50 23.8 24.3 25.9

MAC1015ADADX-RELC 10P 1.50 30.0 30.7 33.6

MAC1515ADADX-RELC 15P 1.50 33.7 35.2 37.9

MAC2015ADADX-RELC 20P 1.50 37.3 38.3 41.6

MAC3015ADADX-RELC 30P 1.50 42.3 44.4 48.7

MAC0225ADADX-RELC 2P 2.50 / / 24.7

MAC0325ADADX-RELC 3P 2.50 / / 25.7

MAC0525ADADX-RELC 5P 2.50 / / 29.4

MAC1025ADADX-RELC 10P 2.50 / / 39.4

MAC1525ADADX-RELC 15P 2.50 / / 44.9

MAC2025ADADX-RELC 20P 2.50 / / 49.8

MAC3025ADADX-RELC 30P 2.50 / / 56.9




Maximum L/R Ratio:

Voltage Rating:







90 V - 300 V - 500 V


Min. +5° C / MAX + 50° C





- Bedding: PVC, LSZH to EN 50290-2

- LEAD or Polyamide Cover

- Inner Sheath: PVC, LSZH to EN 50290-2

- Armouring: Galvanized Steel Wires





EN50

288

IEC

6007

9-14

RAMCRO S.p.A.via Marzorati, 15 - Nerviano

20014 - Milano - Italytel. +39 0331 406 511fax +39 0331 406 559

QD 06/01

Edited by Sales Director on July 2016

Dr. Carlo Croci

Approved by AQ: PC

Documents

Cable indications for - Ramcro · Cable indications for ... On condition the cable gland is not certified as part of the equipment but tested and certified as ... 0.50 sqmm 37.20