Embed Size (px)
Citation preview
Whirlpool UK Appliances Ltd© 2015 Reg. Office: Peterborough PE2 9JB Registered in London: 106725
ServiceInformation
ArcadiaElectronicsIntroductionSupplement
forVented
&Condenser
Dryers
including information on models fitted with the
BPM Motor
5407732 Issue 3 Nov. 2015
C00295636 SM003658
2 of 21
Service Manual UK
Indesit Company
English
SAFETY NOTES & GENERAL SERVICING ADVICE1. This manual is NOT intended as a comprehensive repair/maintenance guide to the appliance.2. It should ONLY be used by suitably qualified persons having technical competence applicable
product knowledge and suitable tools and test equipment.3. Servicing of electrical appliances must be undertaken with the appliance disconnected (unplugged)
from the electrical supply.4. Servicing must be preceded by Earth Continuity, Earth Resistance and Insulation Resistance checks.5. Personal safety precautions must be taken to protect against accidents caused by sharp edges on
metal and plastic parts.6. After Servicing the appliance must be rechecked for Electrical Safety. In the case of appliances which
are connected to a water supply (i.e.: Washing Machines, Dishwashers & Food Centres etc.) checks must be made for leaks from seals gaskets and pipe work and rectification carried out where necessary.
7. It can be dangerous to attempt ‘DIY’ repairs / maintenance on complex equipment and the Company recommends that any problem with the appliance is referred to its own Service Organisation.
8. Whilst the Company has endeavoured to ensure the accuracy of the data within this publication they cannot hold themselves responsible for any inconvenience or loss occasioned by any error within.
INDEX
Safety Notes & General Servicing Advice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Arcadia Introduction Dates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4New Models introduced with Arcadia Electronics - LED Models . . . . . . . . . . . . . . . . . . . . . . . . . . 5New Models introduced with Arcadia Electronics - DIGIT Models . . . . . . . . . . . . . . . . . . . . . . .6 - 7DIGIT Display and Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Model fitted with a BPM Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Arcadia Fault Codes and Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 - 11Fault Codes Quick Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Additional Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Wiring Diagrams:
Condenser Dryer with Heat Pump & Capacitor Run Motor with individual wires . . . . . . . . . 14Condenser Dryer with Heat Pump & Capacitor Run Motor with 3 Way Connector Plug . . . 15Condenser Dryer with Heat Pump & BPM Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Vented Dryer with Heater with 3 separate Motor Wires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Vented Dryer with Heater with 3 Way Motor Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Condenser Dryer with Heater with 3 separate Motor Wires . . . . . . . . . . . . . . . . . . . . . . . . . . 19Condenser Dryer with Heater with 3 Way Motor Connector . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3 of 21
Indesit Company
Service Manual UK English
INTRODUCTION
"Arcadia" is a new Electronic Platform for Tumble Dryers first used in Vented dryer production during July 2012.The new components involved are:
the Display Modulethe Power Module Heater Assembly,
Dimpled Rear Cover and Drain Hole size has changed
Front Air Duct NTC Thermistor
Rear Heater NTC Thermistor
Settings Files Arcadia Settings files start with the digits 50.... (where EVO 2 settings files start 28.....). From September 2012 Arcadia Electronics replaced EVO2 electronics in existing Condenser and Vented models, in a phased introduction.
Heater NTC Thermistor
4 of 21
Service Manual UK
Indesit Company
English
Arcadia Introduction Dates:
Vented Dryers:
New ModelsHotpoint/ Ariston Futura July 2012 New Commercial Codes
Existing ModelsHotpoint / Ariston Futura September 2012 Same Commercial Code as EVO 2 modelsIndesit September 2012 Same Commercial Code as EVO 2 models
Condenser Dryers:
New ModelsHotpoint/ Ariston Futura September 2012 New Commercial Codes
Existing ModelsHotpoint / Ariston Futura September 2012 Same Commercial Code as EVO 2 modelsIndesit September 2012 Same Commercial Code as EVO 2 models
Operation and Programmes of the new Arcadia Machines are very similar to the EVO 2 models, and information can be found in the Futura Tumble Dryer Manual.
Only Arcadia specific information is shown in this Arcadia Manual supplement.
5 of 21
Indesit Company
Service Manual UK English
NEW MODELS INTRODUCED WITH ARCADIA ELECTRONICS - LED
Currently (October 2012) two new Console Interfaces have been introduced along with the Arcadia Electronics.
ARCADIA LED DRYER WITH 3 CONTROL KNOBS
ControlsTwo additional Control Knobs have been added to the usual Programme Dial and Option buttons.The Drying Levels Knob has 8 position, allowing up to 7 drying Levels, depending on the programme selected (see page 7). The 8th position AUTO, defaults the drying level to Cupboard Dry.The Timer Drying Knob allows Timed Dry Periods of 40-60-90-120-140-160-180 minutes.
The Heat and Enjoy CycleThis Cycle heats the clothes at body temperature 37 C, and runs until the customer cancels the cycle or opens the door (or if the cycle is left it times out after 4 hours).
The Heat LED flashes during the cycle and opening the door completes the cycle.
For Other Programmes and options see the EVO 2 Futura Manual.
6 of 21
Service Manual UK
Indesit Company
English
NEW MODELS INTRODUCED WITH ARCADIA ELECTRONICS - DIGIT
ARCADIA DIGIT DISPLAY WITH HEAT LEVEL CONTROL
A New Digital Display Vented and Condenser Models with a New 3 Level Heat Button.The Arcadia Digital Display with Countdown Timer with Option and Warning Icons that illuminate when appropriate.
Empty Water Icon / Container Icon(If the dryer has been plumbed into a drain this icon can be ignored, as there is no need to empty the water container). When this icon is on it reminds you to empty the water container.
If the water container fills during a programme, the heater turns off and the dryer does a period of Cool Tumble then the buzzer sounds, the ‘water container full’ icon flashes, the display shows H20 and
the ‘Empty Water’ icon is on.You must empty the water container and restart the dryer or the clothes will not dry. After restarting the dryer the display will take a few seconds to refresh. To avoid this situation always empty the water container each time you use the dryer.
Heat and EnjoyThis Cycle Heats the Clothes at body temperature 37 C, and runs until the customer cancels the cycle or Opens the door. (or if the cycle is left it times out after 4 hours).
During the Heat & Enjoy Cycle the Small Heat icon is On permanently, the Large Icon Flashes and the Time to End Display is blank.
Pausing the cycle or opening the Door will end the Heat and Enjoy cycle.
PROGRAMME Knob
Display Unit &Selection Buttons
START/PAUSEButton & Light
CHILD LOCKButton & Light
HEAT LEVELButton & Lights
ON/OFFButton
Indicator
OPTIONButtons & Lights
Large Icon No Time to EndSmall Heat Icon On permanently Flashes displayed
7 of 21
Indesit Company
Service Manual UK English
Heat Settings
3 Heat ButtonSome of the Programmes allow all 3 heat level options (Low / Medium / High) to be selected, but this does not apply to all programmes.When the Heat Level options are available, pressing the Heat Level button repeatedly changes the Heat Level and Light corresponding to the selection.Three heat levels indicates three different front sensor target temperatures. e.g: Cotton cycle HH has 50°C of front target, while MH has 40°C and LH 30°C. It enables the user to choose a heat level suited to their clothes.
Note:On vented dryers the 50°C front temperature target is only reached at the end of the cycle, but this setting is necessary to switch on both heaters for all cycles and to reduce the cycle length.For other Programmes and Options see the EVO 2 Futura Manual or the relevant User Handbooks.
Automatic Drying - up to 7 LevelsThe Arcadia Electronic Programmes have up to 7 Drying Levels, Depending on Model and Programme Selected.The actual Drying Performance of the Automatic cycles and Dryness Levels would be affected by drying mixed loads, a load that is not suitable for the selected programme or a very small load.
Symbol Level DescriptionDamp Dry: the most delicate level which makes sure that your clothes are not dripping
any more. After a hand-wash the perfect level to then hang your clothes if you do not want to tumble dry them all the way to the end. Residual humidity 20%.
Iron Dry: a very delicate drying, with the highest residual humidity at 12%.It is useful for garments you would like to iron afterwards.
Hanger Plus: the residual humidity level is 9%.Just the perfect drying status to hang delicate curtains.
Hanger Dry: the residual humidity level is 6%.Just the perfect drying status to hang the garments up.
Light Dry: with 3% of residual moisture is ideal for delicate clothes to be folded and placed into the cupboard.
Cupboard Dry:
the garments are completely dry and are ready to be folded and placed into the cupboard 0%.
Ready to Wear:
the strongest level, used for clothes to be directly worn once the cycle is completed -3%.
8 of 21
Service Manual UK
Indesit Company
English
DIGIT Display and Features
The Display has three main functions, each with its corresponding button.
After selecting a programme that has a Sensor Dry option, press and release the button until the requireddryness sensing level is displayed. If the sensing option is not available with your selected programme, thedisplay will flash and the buzzer will beep three times.! Some sensing programmes do not have all seven dryness level options available.
Dryness levels:
Damp Dry: Dries your items ready to be ironed using a machine or rotary ironer.
Iron Dry: Dries your items ready to be ironed with a hand iron.
Hanger Dry Plus: Dries your delicate items ready to be hanged for final drying.
Hanger Dry: Dries your items ready to be hanged for final drying.
Light Dry: Dries your delicate items ready to be put away.
Cupboard Dry: Dries your items ready to be put away.
Extra Dry: Dries your items ready to be worn.
Timed Dry
Dryness Sensing Levels
Delay Timer
OFF
9.59
After selecting a programme that has a Delay Timer option, a delay start time can be selected.Each press of the Delay Timer button advances the delay setting in 30 minutes increments fromto and then increments from to then and then after five seconds cancels thedelay.For delays of 10 hours or more the display counts down the time in hours until 10 hours, then thedisplay shows and then continues to count down in minutes.For delays 9 hours or less the display shows hours and minutes and then counts down in minutes forall of the delay.After the START/PAUSE button is pressed the delay time can be changed or cancelled.When the delay period finishes the delay icon is off and the Time To End is displayed.Note: During this period the clothes will tumble occasionally to prevent creases developing.
0:309:30 24h
Time to EndIf the delay icon is off the time displayed is the Time to End for the programme running.When timed programmes are selected the time displayed throughout the cycle is the actual time remaining.When Automatic programmes are selected the time displayed is an estimate of the time remaining: When theprogramme is selected the display shows the time required to dry a full load, after around 10 minutes the controllercalculates a better estimate of the cycle time and this is updated during the programme.The Time to End is displayed in hours and minutes and counts down each minute.The colons between the hours and minutes in the display flash to show the time is counting down.The display also shows if there is a problem with your dryer, if this occurs the display will show F followed by a faultcode number, the three option lights and the START/PAUSE light will also flash amber.
After selecting a programme that has a Timed Dry option, press the button and the Timed Dry icon willlight, the display will reduce the selected time each time you press and release this button.Each programme that has a timed option has different times available and the selection ofup to 11 drying times will also depend on the heat setting that your have selected.
Each press of the button decreases the drying time.If you change your mind, press the Sensor Dry button and the sensing level options are available.
If the Timed Dry option is not available the display will flash and the buzzer will beep three times.The selected time remains displayed after the programme starts and can be changed during the programme if you wish.
10h
9 of 21
Service Manual UK
Indesit Company
English
MODELS fitted WITH BPM MOTOR
SPECIFIC BPM PROGRAMMESThe BPM (Brushless Permanent Magnet) Motor is a variable speed motor controlled by the Module.There are 3 New Cycles available for models fitted with a BPM motor.1. DARK CYCLEThe Dark Cycle helps to maintain dark coloured clothes.By controlling the motor speed and drum rotation together with a lower drying temperature.Maximum 3kg Load of Jeans and Cottons:Programme ProfileFront target temperature reaches 40°C.Distribution Speed (70 rpm) once conductivity value is 3000 (15% humidity)Target Temperature during Distribution reaches 45°CEnd of Cycle Sensed by Conductivity Sensor + 10 min timed phaseCycle Target: dark garment care (less fading)Achievement: 22% less colour fade in jeans. Less lint on cotton fabric surface.
2. LESS FLUFF CYCLETarget: less fluff into filter after cotton cycles (compared with fixed motor speed machines)Distribution Speed once load = 15% humidity.
3. TURBO DRYAn extra fast drying cycle to dry cottons (i.e.: Cottons and Bed & Bath) by using the combination of high temperature and a special motor speed profile that takes advantage of our new Soft Motion motor system.The Turbo Cycle is for 7 Kg loads. Dries to Hanger dry dryness level (6%).Programme ProfileHeater: Both Elements are always onDrum Speed:58 rpm until conductivity Level reaches 120055 rpm until conductivity reaches 2000. 60 rpm until end cycle.Cycle End Condition: Conductivity sensor reading.
Drive shaftBPM motor
connectors
BPM motor
10 of 21
Service Manual UK
Indesit Company
English
ARCADIA FAULT CODES and DIAGNOSTICS
In the Event of a Fault the Options indicators and Start/Pause LED will flash rapidly.DIGIT models will show a fault code in the display in the format, Fxx. See page 11 for guidance on the fault cause.
VENTED - LED MODELS (Example)
In the Event of a Fault the Options and Start/Pause LEDs will flash rapidly.The Fault Code can be identified by one vertical LED or a combination of the Vertical LEDs being "ON". See the Table below. See page 11 for guidance on the fault cause.
FAULT CODE
LED CombinationLED 4 LED 3 LED 2 LED 1
F01 OFF OFF OFF ONF02 OFF OFF ON OFFF03 OFF OFF ON ONF04 OFF ON OFF OFFF05 OFF ON OFF ONF06 OFF ON ON OFFF07 OFF ON ON ONF08 ON OFF OFF OFFF09 ON OFF OFF ONF10 ON OFF ON OFFF11 ON OFF ON ONF12 ON ON OFF OFFF13 ON ON OFF ONF14 ON ON ON OFFF15 ON ON ON ON
4321
All Option and Start/Pause LEDs will also flash
LED’s
11 of 21
Service Manual UK
Indesit Company
English
ARCADIA FAULT CODES and DIAGNOSTICSCONDENSER LED Models
In the Event of a Fault the Options and Start/Pause LEDs will flash rapidly.The Fault Code can be identified by one vertical Led or a combination of the Vertical Led's being "ON". See the Table below.See page 11 for guidance on the fault cause.
FAULT CODE
LED CombinationLED 5 LED 4 LED 3 LED 2 LED 1
F01 OFF OFF OFF OFF ONF02 OFF OFF OFF ON OFFF03 OFF OFF OFF ON ONF04 OFF OFF ON OFF OFFF05 OFF OFF ON OFF ONF06 OFF OFF ON ON OFFF07 OFF OFF ON ON ONF08 OFF ON OFF OFF OFFF09 OFF ON OFF OFF ONF10 OFF ON OFF ON OFFF11 OFF ON OFF ON ONF12 OFF ON ON OFF OFFF13 OFF ON ON OFF ONF14 OFF ON ON ON OFFF15 OFF ON ON ON ONF16 ON OFF OFF OFF OFFF17 ON OFF OFF OFF ON
4
All Option and Start/Pause LEDs will also flash
5
321
LED’s
12 of 21
Service Manual UK
Indesit Company
English
FAULT CODES - QUICK GUIDE for Models fitted with an Arcadia ModuleNOTE: This information ONLY a guide to possible solutions.Other components (not mentioned here) or the way the product is used could also cause fault codes to be displayed. Filters and Vent Hoses should always be checked for blockage.Before investigating any Heating / Not Heating or Temperature related faults, always check that the Cycling and One-Shot Thermostats are not Open Circuit (O/C). If the One-Shot Thermostat is O/C, it does NOT create an individual Fault Code, but a temperature / heating related fault code will be displayed.
F01 Motor Circuit Fault Check Motor and Motor Wiring and Connections, including relevant module edge connector.Check Door Switch and wiring and Connections.C or B Energy Models: Check Heater and Heater circuit including Cycling Stat, and attached connections including the relevant Module connections.Heat Pump Models:Check Compressor and wiring and connections
F02 Motor Fault -Open or Short circuit
Check Motor and Motor Wiring and Connections, including relevant module edge connector.
F03 Front NTC Check Front NTC and attached wiring and module connections including relevant module connections. Check for trapped wiring below the air duct.
F04 Rear NTC No rise in temperature detected: Check Heater circuit including Cycling Thermostat, One-Shot Thermostat, Heater and wiring. Also check Rear NTC Thermistor Open or Short Circuit. Check Rear NTC (attached to heater Frame) and attached wiring and module connections including relevant module connections.
F06 Heat Pump Refrigerant NTC open or short circuit
Heat Pump Models only. Check NTC, attached to the refrigerant circuit, Check attached wiring and module connections including relevant module connections.
F07 Compressor - Open or Short Circuit
Heat Pump Models only. Test the Compressor, Capacitor, and attached wiring and connections including the relevant edge connector.
F08 Heater - Open or closed Circuit
C and B Energy Models. Test Heater and Heater circuit including the Cycling Stat.Check attached connections including the relevant Module connections.
F09 File Setting Corrupted Rewrite settings file using EMIT, Smartcard or PDA.
F12 Communication Error Check the wiring harness between the Display and Power Modules.
F13 Air Duct NTC Overheating
Check the Machines Filter is Clean.Check the machines air flow for blockages.Check the machines Plinth and air vents are not restricted or blocked.Check the NTC and attached Circuit and Connections.Heat Pump Models. Check the Front Filter (behind the Plinth) is clean and the housing is not blocked with fluff.
F14 Rear NTC Over Heating Check the Cycling Thermostat is operating correctly.Check the Machines Filter is Clean.Check the machines air flow for blockages.Check the machines Plinth and air vents are not obstructed or blocked.Check the NTC and attached Circuit and Connections.
F15 Cool NTC Overheating(Refrigerant Circuit)
Heat Pump Models only. Check NTC, attached to the refrigerant circuit, Check attached wiring and module connections including relevant module connections
F18 BPM Communication Check BPM motor plus wiring and connections between the motor and module.
13 of 21
Indesit Company
Service Manual UK English
Additional InformationRear (Heater Thermistor)
Temperature Resistance Reading (approximate)25 C 100 K Ohms
140 C 2.282 K Ohms ± 1.7%
Front Air Duct ThermistorTemperature Resistance Reading (approximate)
25 C 49 K Ohms to 51 K Ohms80 C 5.974 K Ohms to 6.588 K Ohms
IndesitCom
pany
14 of 21
Service Manual U
KEnglish
J1
J6J3
J2
J4
J5
J8
J9
J10
J11J13J14 **
J14 **
J16J17
PCB numberingConnector numbering
54321
54321
12345
1 1 22 3 4 5 1 2 23 4 5 6 1 3 4 5 67 77 6 5 4 3 2 1
1 2 3 4 5 6 77 6 5 4 3 2 1
Blue
blue
red
red
red black
brown
black
blackIP
red
black
white
L
N
4,8Black
Blue (Brown)
BrownBrown
E
ABCDEFG
Display ModuleFloat SwitchRefrigerant NTC ThermistorFront NTC ThermistorDoor SwitchMotor with internal protectorMotor Capacitor
HIJKLM
Drain PumpCooling FanCompressor and OverloadCompressor CapacitorDrum / Drum Sensing StripMains terminal Block / Suppressor
Legend:
Arcadia ModuleCondenser Dryer with Heat Pump& Capacitor Run Motor with individual wires
PSblue
C
S
RPB
PB
f
m
PB = Piggy Back Connector | m = Male | f = Female
Blue (Brown) = Alternative wiring colour
PBPB
D
A
B
I
F
K
L
M
J
C
EH
G
Drg. Ref: 5407800.pdf21-02-2014
IndesitCom
pany
15 of 21
Service Manual U
KEnglish
J1
J6
J2
J3
J4
J5
J8
J9
J10
J11J13J16J17
J14 **
PCB numberingConnector numbering
J14 **
54321
54321
12345
1 1 22 3 4 5 21 3 4 5 6 7
1 2 3 4 5 6 77 6 5 4 3 2 1
1 2 3 4 5 6 77 6 5 4 3 2 1
Blue
redredredred
redredred
red
red
brown
black
black
L
N
4,8Black
Brown
Blue (Brown)
Brown
E
ABCDEFG
Display ModuleFloat SwitchRefrigerant NTC ThermistorFront NTC ThermistorDoor SwitchMotor with internal protectorMotor Capacitor
HIJKLM
Drain PumpCooling FanCompressor and OverloadCompressor CapacitorDrum / Drum Sensing StripMains terminal Block / Suppressor
Legend:
Arcadia ModuleCondenser Dryer with Heat Pump& Capacitor Run Motor with a3 Way Connector plug
PS
C
S
RPB
PB
IP
red blackwhite
3 2 1
PB = Piggy Back Connector | m = Male | f = FemaleBlue (Brown) = Alternative wiring colour
f
m
f
m
D
A
B
IK
LM
J
C
EH
GF
Drg. Ref: 5407801.pdf24-02-2014
IndesitCom
pany
16 of 21
Service Manual U
KEnglish
J1
J6
J2
J3
J16J17
J14 **
PCB numberingConnector numbering
J14 **
54321
12345
1 1 22 3 4 5
1 2 3 4 5 6 77 6 5 4 3 2 1
1 2 3 4 5 6 77 6 5 4 3 2 1
Blue
Red
Red
brown
Black
Black
L
N
4,8Black
BrownBrown
E
ABCDEFG
Display ModuleFloat SwitchRefrigerant NTC ThermistorFront NTC ThermistorDoor SwitchBPM Motor
HIJKL
Drain PumpCooling FanCompressor and OverloadCompressor CapacitorDrum / Drum Sensing StripMains terminal Block / Suppressor
Legend:
Arcadia ModuleCondenser Dryer with Heat Pump& BPM Motor
C
S
RPB
PB
Blue (Brown)
PB = Piggy Back Connector | m = Male | f = Female
Blue (Brown) = Alternative wiring colour
f
m
A
I
K
L
JH
Drg. Ref: 5407802.pdf24-02-2014
J4
J5
J8
J9
J10
J11J13
54321
4321
21 3 4 5 6 7R
ed
Red
Red x 4
D
B
C
E
F
Red
Red
PS G
IndesitCom
pany
17 of 21
Service Manual U
KEnglish
J1J2
J3
J4
J5
J8
J9
J10
J11J13J16J17
J14 **
PCB numberingConnector numbering
J14 **
21
54321
12345
1 1 22 3 4 5 21 3 4 5 6 7
1 2 3 4 5 6 77 6 5 4 3 2 1
1 2 3 4 5 6 77 6 5 4 3 2 1
Blue
blue
blue
red
black
IP
red
black
white
L
N
4,8 mmBlack
Blue (Brown)
Brown
E
ACDEFG
Display ModuleRear NTC ThermistorFront NTC ThermistorDoor SwitchMotor with internal protectorMotor Capacitor
HIJKL
Cycling ThermostatHeaterOne Shot Cut-outDrum / Drum Sensing StripMains terminal Block / Suppressor
Legend:
Vented Dryer with Heaterwith 3 separate motor wires
Arcadia Module
A
D
IF
K
L
HJ
C
E
G
Drg. Ref: 5407808.pdf24-02-2014
IndesitCom
pany
18 of 21
Service Manual U
KEnglish
J1J2
J3
J4
J5
J8
J9
J10
J11J13J16J17
J14 **
PCB numberingConnector numbering
J14 **
21
54321
12345
1 1 22 3 4 5 21 3 4 5 6 7
1 2 3 4 5 6 77 6 5 4 3 2 1
1 2 3 4 5 6 77 6 5 4 3 2 1
Blue
L
N
4,8 mmBlack
Blue (Brown)
Brown
E
ACDEFG
Display ModuleRear NTC ThermistorFront NTC ThermistorDoor SwitchMotor with internal protectorMotor Capacitor
HIJKL
Cycling ThermostatHeaterOne Shot Cut-outDrum / Drum Sensing StripMains terminal Block / Suppressor
Legend:
Vented Dryer with Heaterwith 3 way motor connector
redred
redredred
IP
red blackwhite
3 2 1
GF
Arcadia Module
A
D
I
K
L
HJ
C
E
24-03-2014
Drg. Ref: 5407809.pdf24-02-2014
IndesitCom
pany
19 of 21
Service Manual U
KEnglish
J1J2
J3
J4
J5
J8
J9
J10
J11J13J16J17
J14 **
PCB numberingConnector numbering
J14 **
54321
21
54321
12345
1 1 22 3 4 5 21 3 4 5 6 7
1 2 3 4 5 6 77 6 5 4 3 2 1
1 2 3 4 5 6 77 6 5 4 3 2 1
Blue
blue red
black
IP
red
black
white
L
N
4,8Black
Blue
Brown
E
ABCDEFG
Display ModuleFloat SwitchRear NTC ThermistorFront NTC ThermistorDoor SwitchMotor with internal protectorMotor Capacitor
HIJKLM
Drain PumpCycling ThermostatHeaterOne Shot Cut-outDrum / Drum Sensing StripMains terminal Block / Suppressor
Legend:
PSblue
Arcadia ModuleCondenser Dryer with Heaterwith 3 separate motor wires
A
B
D
I
F
K
L
M
J
C
EH
G
Drg. Ref: 5407811.pdf25-03-2014
IndesitCom
pany
20 of 21
Service Manual U
KEnglish
J1J2
J3
J4
J5
J8
J9
J10
J11J13J16J17
J14 **
PCB numberingConnector numbering
J14 **
54321
21
54321
12345
1 1 22 3 4 5 21 3 4 5 6 7
1 2 3 4 5 6 77 6 5 4 3 2 1
1 2 3 4 5 6 77 6 5 4 3 2 1
Blue
L
N
4,8Black
Blue (Brown)
Brown
E
ABCDEFG
Display ModuleFloat SwitchRear NTC ThermistorFront NTC ThermistorDoor SwitchMotor with internal protectorMotor Capacitor
HIJKLM
Drain PumpCycling ThermostatHeaterOne Shot Cut-outDrum / Drum Sensing StripMains terminal Block / Suppressor
Legend:
Arcadia ModuleCondenser Dryer with Heater
PS
redred
redredred
IP
red blackwhite
3 2 1
GF
with 3 way Motor connector A
B
D
IK
L
M
J
C
E
H
27-03-2014
Drg. Ref: 5407812.pdf27-03-2014
Indesit Company
21 of 21
Service Manual UK English
