BC POLICY#__1__11/2006 1

MANUAL No._____

Bullard Company

EMPLOYEE SAFETY

MANUAL

BC POLICY#__1__11/2006 2

BULLARD COMPANY EMPLOYEE SAFETY MANUAL

BC POLICY#__1__11/2006 3

NOVEMBER 2006 BULLARD COMPANY SAFETY POLICY Safety is of primary importance in our operation. Each of us has the responsibility to make the safety of ourselves and our co- workers a basic concern. This objective is fundamental to well being, as well as to the efficient operation of our business. This manual is intended to assist you in performing your work safely. With few exceptions, every safety rule or practice in this manual has evolved from experience and knowledge gained over many years in how to prevent accidents and injuries. Every employee has the responsibility to prevent accidents and injuries by observing established working rules, by following the directions of supervisors, by practicing the safety rules of BULLARD COMPANY, and by providing ideas on how our safety efforts might be further strengthened. BULLARD COMPANY management recognizes its responsibility to provide healthful and safe working conditions, safe working rules based upon experience and safety knowledge, and competent work direction. BULLARD COMPANY and its employees have the responsibility to comply with all federal, state, and local regulations related to safety and health programs. If you think something you are about to do is unsafe, do not do it. Stop Work and correct the situation. If you cannot correct the situation, ask your supervisor for assistance. This is important, it is your life that may be in danger. If you see someone about to commit an unsafe act, stop them and discuss it with them. Help your co-worker. Make your work environment safe for everyone. Employees working for BULLARD COMPANY shall be required to comply with health and safety laws and regulations and to adopt the safety practices for BULLARD COMPANY If you do not follow the safety rules, you could be dismissed. Leonard C. Bullard Jr., President

BC POLICY#__1__11/2006 4

CONTENTS Section 1 GENERAL SAFETY RULES Introduction Rules and Regulations 1. Smoking 2. Intoxicating Beverages, Drugs and Firearms 3. Reporting Accidents/Injuries 4. Reporting Unsafe Conditions and Near Misses 5. Horseplay 6. Housekeeping 7. Head and Facial Hair Policy 8. Wearing Apparel 9. Chemicals and Solvents 10. Overhead Work 11. Hot Work and Entry Permits 12. Lockout/Tagout Procedures 13. Iron Sulfide 14. Asbestos and NORM 15. Scaffolds and Platforms 16. Hoist 17. Trucks and Forklifts 18. Office Safety General Principles Slips, Trips, and Falls Electrical Safety Supervisory Responsibilities Section 2 PROTECTIVE EQUIPMENT Introduction Ears Eyes Feet Hands Head & Face Respiratory Safety Belts

BC POLICY#__1__11/2006 5

Clothing Section 3 TOOLS AND EQUIPMENT Ladders Scaffolding Power Tools Dead Man Valves Grounding Company Vehicles Section 4 ABRASIVE BLASTING & SPRAY PAINTING Abrasive Blasting Spray Painting Section 5 WELDING AND CUTTING Section 6 FIRST AID Introduction General Severe bleeding No breathing/circulation Heart attack Choking Inhalation of toxic gas or smoke Electric shock Burns Exposure to crude products Shock Heat exhaustion Heat stroke Poison plants Swallowed poisons Inhalation of Hydrogen Sulfide

BC POLICY#__1__11/2006 6

Failure to observe applicable safety rules could result in serious injury to yourself or your co-workers. For this reason, unsafe work practices could result in discipline up to and including termination. It is not within the scope of this Safety Manual to detail all government regulations or safety procedures, but provide an overview of our safety requirements.

BC POLICY#__1__11/2006

7

SECTION 1 GENERAL SAFETY RULES INTRODUCTION Always keep in mind that your primary responsibility as an employee is to perform your duties in a safe manner in order to prevent injury to yourself or to your co-workers. You should become familiar with the contents of this manual and MUST learn the approved safe practices applicable to your work. INDIVIDUAL RESPONSIBILITIES Each employee is responsible for his/her own safety and for the safety of other workers. Remember that one of the primary responsibilities as an employee is to perform duties in a safe manner. Employees must comply with rules and practices in performance of their job. Report injuries/illnesses, unsafe conditions and other incidents immediately. Assist in incident investigations as necessary. RULES AND REGULATIONS 1. SMOKING Smoking is permitted only in locations specifically designated at the facility. Employees must never smoke outside of designated smoking areas whether "NO SMOKING" signs are posted or not. Employees will observe all smoking rules at other locations. 2. INTOXICATING BEVERAGES, DRUGS, AND FIREARMS Possession of illegal drugs, drug paraphernalia, intoxicating beverages, firearms or other weapons is prohibited on company premises. "Company Premises" for BULLARD COMPANY includes all property, facilitates, land platforms, pipe yards, buildings, structures, fixtures, installations, boats, aircraft, automobiles, trucks, and all other vehicles, whether owned, leased, or used by the company. This also includes any other work location or mode of transportation to and from those locations while in the course and scope of BULLARD COMPANY employment. Persons found to be in possession of these items or under the influence of drugs or alcohol will be removed from the company property. Entry into BULLARD COMPANY property is conditioned upon the company's right to conduct unannounced searches for such contraband. Any employees caught with or under the

BC POLICY#__1__11/2006

8

influence of alcohol, drugs or firearms on the job site, or in a company vehicle will be sent to the proper authorities and dismissed. Employee using prescribed drugs, that could affect their ability to work safely, must notify his/her supervisor before working. 3. REPORTING ACCIDENTS/INJURIES All accidents and injuries, no matter how minor, must be immediately reported to your supervisor. An accident report must be completed within 24 hours. If an accident occurs while at another location (while on company business) you must report the accident to the client representative, and follow all the prescribed rules of that location. You must notify your supervisor (BULLARD COMPANY) as soon as possible. You must report all company owned, leased, or rented vehicle, equipment and/or job related automotive accidents, as soon as possible. 4. INCIDENT REPORTING - OBSERVATION/INCIDENT/EVENT All incidents shall be reported promptly to your supervisor and corrected accordingly. If on another work location report the unsafe condition to the client representative (and BULLARD COMPANY supervisor). Near miss accidents that could have resulted in injury or damage shall be reported immediately so corrective action can be taken. An Incident Reporting form must be filled out as soon as possible. 5. HORSEPLAY Horseplay, such as wrestling, practical jokes, and etc can be dangerous and is prohibited. Horseplay and fighting on "Company Premises" could result in dismissal of all employees involved. 6. HOUSEKEEPING Work areas shall be maintained in a neat and orderly manner. Trash, oil spills, etc., must be cleaned up as soon as possible. Aisles and emergency exits must be kept free of materials at all times. Free access to fire extinguishers and circuit breakers must be maintained at all times. SHOP * Tools, electrical cords, and hoses must be kept in their proper place when not being used. Air hose and electrical cords must be inspected prior to using. Any hose or cord that is defective must be repaired or disposed. If repairs can not be done they must be tagged and set aside for repair. When using electrical cords and air hoses they must not be a tripping hazard. * Put empty boxes, packaging materials, and other waste materials in the trash barrel. Never allow the trash barrel to overflow.

BC POLICY#__1__11/2006

9

FLOOR AND WORK AREA Keep floors swept up and other work areas clean. If there is a spill, clean up as soon as possible. PAINT STORAGE * Only paint and paint products will be stored in the paint storage. All containers in the paint storage must have a proper label. NEVER STORE ANY REACTIVE MATERIALS IN THE PAINT STORAGE BUILDING. * Empty boxes and other packing material must not be stored in the paint storage. * Containers that have been opened must be secured to prevent spilling. * Stack cans properly to prevent them from falling. * Report any leaking container to your supervisor, and then follow cleanup procedure. NEVER OPERATE ANY EQUIPMENT THAT NEEDS REPAIRS THAT COULD CAUSE INJURY TO YOU OR OTHERS. AIR COMPRESSORS Check oil, and water daily. Ground the air compressor each time you use it. Keep the air compressor clean. Oil spills can be a hazard. 7. HEAD AND FACIAL HAIR POLICY This policy has been adopted for all persons working in areas where a respirator may be required. It prohibits long hair, long sideburns, long mustaches, beards, vandykes, goatees, etc. that will affect the safe use of a respirator. The following activities will require compliance with this policy: a. Use respiratory equipment during work activities. b. You are assigned the equipment or have equipment designated and available for their use. c. You are expected to respond to and have been trained to participate in emergencies and/or rescue of personnel where such incidents require respiratory equipment. d. You are expected to respond and assist with efforts to control a hazardous incident, where such efforts require respiratory equipment. 8. WEARING APPAREL Clothing suitable for the job shall be worn. Ragged loose fitting clothing and jewelry (rings, watches, necklaces, etc.) can catch on materials and cause serious injury. All clothing that becomes saturated with petroleum products or hazardous chemicals must be removed promptly. Flame retardant clothing (FRC) is required at many work locations. The company will furnish FRC for those individuals that are required to wear FRC. At work locations that do not require FRC you must wear long pants, and most locations require long sleeves.

BC POLICY#__1__11/2006

10

9. CHEMICALS AND SOLVENTS Material Safety Data Sheets will be available for chemicals used on the job site and personnel will be instructed in their safe use. Protective equipment outlined on the MSDS will be provided to and worn by exposed personnel. Low flash point solvents such as gasoline shall not be used for washing and cleaning. 10. OVERHEAD WORK When working over head, the area below shall be roped off or other equivalent measures taken to protect workers on the work site. Signs reading "Danger - Work overhead" should be conspicuously posted. Employees shall NEVER PASS UNDER A SUSPENDED LOAD. BULLARD COMPANY employees are not permitted to work under any overhead load unless it is supported. 11. HOT WORK AND ENTRY PERMITS BULLARD COMPANY PERSONNEL ARE PROHIBITED FROM ENTERING ANY AREA WHERE TOXIC GAS MAY BE PRESENT, UNTIL THE AREA HAS BEEN CHECKED AND DETERMINED TO BE FREE OF GAS. PROPER PERMITS MUST BE AT THE LOCATION. You are REQUIRED to obtain a hot work permit before you perform any of the following work, at any location other than the normal work station. 1. Welding 2. Torching 3. Grinding 4. Chipping 5. Sandblasting 6. Spray painting near spark-producing equipment 7. Any other spark producing operations ENTRY PERMITS BULLARD COMPANY employees are not permitted to enter a "Permit Required Confined Space that is IDLH (immediately dangerous to life and health)". All equipment that would be worked by BULLARD COMPANY employees will be decontaminated prior to any work being preformed. DEFINITION: CONFINED SPACE A confined space has a limited or restricted means of entry or exit, it is large enough for an employee to enter and perform assigned work, and is not designed for continuous occupancy by the employee. These spaces may include, but are not limited to, underground vaults, tanks, storage bins, pits and dike areas, vessels, and silos. A PERMIT-REQUIRED CONFINED SPACE

BC POLICY#__1__11/2006

11

Is one that meets the definition of a confined space and has one or more of these characteristics: (1) contains or has the potential to contain a hazardous atmosphere, (2) contains a material that has the potential for engulfing an entrant, (3) has an internal configuration that might cause an entrant to be trapped or asphyxiated by inwardly converging walls or by a floor that slops downward and tapers to a smaller cross section, and/or (4) contains any other recognized serious safety or health hazards. 12. LOCK OUT - TAG OUT PROCEDURES A lockout/tagout system is required when equipment capable of producing energy is placed out of service for repairs. In addition to electric panel boards and breaker boxes, hydraulic, steam, high-pressure lines and other energy producing equipment are included. The lockout/tagout system must be capable of preventing unauthorized start-up of the equipment being serviced. You are REQUIRED to lock and tag any and all valves that are connected to the tank or vessel. 13. IRON SULFIDE Iron sulfide is a scale deposit which can be found in any sour (crude oil or gas) production equipment. It will ignite and burn spontaneously when exposed to air unless it is kept wet. Should you encounter iron sulfide hose down the scale with water and consult with your supervisor and/or the location supervisor. 14. ASBESTOS AND NORM During maintenance activities which involve removing insulating materials or removing scale deposits from production equipment, asbestos, man-made mineral fibers or naturally occurring radioactive material (NORM) health hazards may be encountered. When either of these hazards occur (or suspected) contact your supervisor. ASBESTOS Asbestos exposure is most likely to occur in areas where asbestos has become friable (brittle, dried-out, easily broken up into tiny fragments) or where asbestos-containing material is being disturbed or removed. Asbestos is a known carcinogen (causes cancer). Inhalation is the primary route of exposure. Asbestos fibers breathed into the lungs can cause cancer many years later. N.O.R.M. Workers may be exposed to possible external or internal radiation. External exposure can be controlled by limiting exposure time. Internal hazard occurs when airborne radioactive materials are inhaled, ingested, or enter the skin through open wounds. These hazards can be minimized by properly wearing an approved respirator and by protecting wounds and cuts. Wetting the loose material with water can also prevent inhalation. All additional safety precautions must be followed

BC POLICY#__1__11/2006

12

when working with this type of hazard. 15. SCAFFOLDS OR PLATFORMS All scaffolds or platforms used for maintenance or inspection shall be constructed/maintained and used in compliance with the applicable occupational health and safety construction regulations. See Section 3 for additional information. 16. HOISTS 1. Each hoist operator is directly responsible for the safe operation of his/her hoist when moving loads. When there is any doubt as to the safety, the hoist operator should stop his/her hoist immediately, and should continue only when a safe condition exists. 2. A good rule for hoist safety is to assume that any suspended load will fall at any moment. If the operator keeps this possibility in mind; everyone will be safe around the operation of hoist in the event the load should become unhooked or slip and fall. The operator shall not leave his/her position at the controls while the load is suspended. 3. It is the responsibility of the hoist operator to see that the load is properly secured and hitched. It is also the operator’s responsibility to see that all materials, tools, or loose objects have been removed from the load before the lift is started. 4. The hoist operator must obey EMERGENCY SIGNALS from anyone. 5. Worn or damaged slings (fiber, wire rope or chain) are not to be used. The supervisor should be notified immediately. Slings must be inspected before each use. 6. Slings are not to be altered; only OSHA 1910.184 alterations can be made to slings. 7. Loads are never to be taken over the head of anyone working on the floor of the shop or yard. 8. Each employee is to be aware of the overhead lifts in his/her area, and move out of the way when the hoist operator is moving an overhead load through his/her area. 17. TRUCKS AND FORKLIFTS 1. Only trained and authorized personnel shall operate any motorized equipment. 2. Each truck and forklift operator is directly responsible for the safe operation of his/her vehicle. If there is any doubt of safety, the operator is to stop his/her vehicle immediately. He/she will continue only when a safe condition exists.

BC POLICY#__1__11/2006

13

3. If a helper is assigned to assist the operator, it is their responsible to see the load is properly secured. It is his/her responsibility to see that all loose materials and/or tools have been removed from the load before a lift is started. 4. The truck or forklift operator is to take signals from only one person during a lift or move, but must obey EMERGENCY signals from anyone. 5. No driver will allow any person to ride on a truck, car or forklift outside the confines of the cab. 6. Under no circumstances is an individual to ride on a load being hauled or lifted by a truck or forklift. 7. Yard equipment must never be driven at excessive speed in the yard. The maximum speed limit is ten (10) miles per hour. 8. The operator shall use extreme caution when driving into or near shop doors or other areas where people on foot may step in the way of a moving vehicle. 9. Daily inspection of vehicles is a must. Report any problems to your supervisor. Slings and wire rope (cable) should be inspected per OSHA 1910.184. 10. The helper (or anyone) should never place himself/herself between the truck and load. 11. The truck operator must know the winch capacity and the load capabilities of the vehicles. They should also know the approximate weight of the load to be moved. 12. Forklift operators must know the weight capacity of their forklift, and the center of gravity. 13. Forklifts will have a pre-use visual inspection prior to use. In areas of multi-shift operations, an inspection will be made at the start of each shift. The lift truck operator will be responsible for checking the following: a. Battery and plug connections l. The mast and fork will be checked for wear, b. Brakes (emergency or park) warped or bent structures. c. Lights m. Check fire extinguisher d. Horn and back-up alarm n. Name plate or maximum lift weight must be e. Hour indicator posted on side of lift truck. f. Steering g. Tires h. Hydraulic controls i. Motor oil level and pressure j. Water level and fan belts

BC POLICY#__1__11/2006

14

k. Fuel level 18. OFFICE SAFETY * Lifting 1. Plan Ahead a) Know your strength. When in doubt make it a two-person job. b) Make sure you have a place to put the heavy object and that doors are open and obstacles are out of your way before you start. c) Always make sure your footing is secure. 2. Lift and Carry the Right Way a) Use you arm and leg muscles, not your back. Keep your back straight and load close to your body. b) Grasp the object firmly. Hold it so that your fingers won't be pinched if the load shifts. c) Make sure that you can see. Have plenty of light and be able to look over your load. d) Set the object down using your arm and leg muscles. If it is a box, rest one corner first so that the hands don't get caught underneath. * Avoid Falls Most office falls are on the level floor and can be eliminated. 1. Avoid overloading top drawers of filing cabinets. This could bring the cabinet down on you. 2. Close one drawer of a filing cabinet before you open another. With all drawers open the filing cabinet could fall on you. 3. Keep filing cabinets and desk drawers closed when not in use. 4. Keep the floor clean. Pick up everything. Remove all cords or securely tape them down. 5. Clean up wet spots from beverages or water. 6. Don't stand on chairs; use a ladder or step stool. * Avoid Machine and Equipment Accidents 1. Keep fingers out of openings when closing drawers or doors. 2. Read the instructions or listen to oral instructions carefully. Never use machines you don't know how to operate. 3. Make sure that mechanical guards are in place every time you use a machine. If you remove a guard temporarily, be sure to replace it before you turn on the switch. 4. Turn machines off while adjusting them or when not using them.

BC POLICY#__1__11/2006

15

5. Be alert for electrical hazards. If a machine overheats, smokes, or sparks, or if you feel a slight shock, unplug it and call a service man. 6. Watch your clothes - long sleeves, scarves, ties, hair, dangling jewelry, or even key chains are dangerous around machines with moving parts. 7. Check the machine position before use. See that typewriters, duplicators, or adding machines are firmly on the working surface. 8. Open packages the safe way. Inspect for sharp projections and rough edges, cut away from the body, and use the right tools for the job. * Avoid Cuts and Punctures 1. Keep pointed objects in a box or drawer where they can't stab you. 2. Don't try to cut too many sheets of paper at once in a paper cutter. 3. Use rubber finger guards when working with stacks of paper. Use a sponge or sealing device to moisten stamps or envelopes. 4. Sweep pieces of broken glass up instead of picking them up by hand, and then wrap the pieces in paper. Glass splinters can be picked up with a damp paper towel. * Housekeeping Housekeeping makes work easier and conditions safer because the work area is clean, materials are arranged properly and used materials are properly disposed. 1. Place any shipping or packing materials in the proper garbage container. 2. Store chemicals and flammables carefully. Make sure they are labeled and sealed in approved containers. 3. Put knives and shears away for use. 4. Keep heavy cartons at floor level out of walkways. * Be Alert for Fire Hazards 1. If you smell smoke, be prepared for a fire. 2. Know where fire extinguishers are located and know how to use them. 3. If you spot a fire: a) Turn on the alarm. b) Alert others without causing panic. c) Use available fire fighting equipment (incipient stage fires only). d) Follow fire evacuation procedures. e) Keep out of the way when the professional fire fighters come. * General 1. DO NOT wander about the shop unless your job requires you to do so, and you have been instructed to do so by your supervisor.

BC POLICY#__1__11/2006

16

2. Never interrupt anyone operating a machine or in the act of performing any other job as both the operator and you may be injured if their attention is divided. 3. Walk - do not run unless an emergency such as a fire or explosion occurs. Report all injuries, regardless how slight, to your supervisor. GENERAL PRINCIPLES 1. Adequate rest, exercise and proper diet will enhance your health and level of awareness which is helpful in avoiding accidents. 2. Be alert to hazardous conditions. Whenever possible, correct or eliminate the hazardous condition yourself. Report to your supervisor all such hazards and the measures taken to correct them. If a hazard cannot be corrected immediately, clearly mark it until it can be corrected. 3. When working alone, notify another person of your work location, and always try to anticipate any hazards that you might encounter. You should NOT attempt to do a job alone when safe working practices and common sense tell you help is needed. 4. NEVER defeat the function of a safety device. Report all safety device malfunctions to your supervisor as soon as possible and flag the device immediately to warn other personal of the hazard. 5. NEVER attempt to lift or move a heavy object that is beyond your capability to do so in a safe manner. 6. Use the prescribed protective equipment for the work you are doing. 7. DO NOT use makeshifts of any kind that could conceivably compromise safety. 8. Be careful, when moving about the work area, to avoid slipping, or falling. 9. Preoccupation with matters other than the work at hand causes accidents. When performing a job, concentrate on the immediate assignment. DO NOT be distracted by your emotions or by outside influences. 10. When on a duty away from the facility, you should become familiar with all emergencies procedures and escape routes at the work location. 11. Smoking is permitted in designated areas only. 12. Under normal operations, all operating machinery and electrical switch gear must have all safety guards, switches and alarms in place and be functional.

BC POLICY#__1__11/2006

17

13. Operation of equipment having a "DANGER, DO NOT OPERATE" tag is prohibited. 14. Do not apply compressed air to yourself or others. 15. When ascending or descending stairways, use the handrail and take one step at a time. 16. Running in work areas, except for emergency purposes, is prohibited. 17. Use only proper tools and equipment maintained in good working condition. 18. Erect barricades/flagging around areas of hazardous work, such as holes in decking and work areas, trenches and overhead hazardous work. 19. Fire extinguishers and all other emergency equipment must be in good condition, inspect regularly and kept clear of any obstruction. You must have clear access to fire extinguishers and circuit breakers. 20. All chemical containers shall be properly labeled. 21. Approved hard hats shall be worn in the field operations and other designated areas. Metal hard hats are prohibited. 22. Approved foot protection is required in field operations and other designated areas. 23. Eye/face protection such as goggles, safety glasses with side shields, and/or a face shield shall be worn during grinding, welding, drilling, scraping or any operation where foreign object may enter the eye. 24. Hearing protection shall be worn in high noise areas (85 dB or higher). 25. Wear proper hand protection when performing tasks that may present injury to hands. SLIPS, TRIPS, and FALLS Slips, trips, and falls are a major contribution to injuries and lost time accidents. Be careful and observe the following rules. 1. The following situations should be avoided to help prevent slipping: a. Wet floors/decks b. Oily floors/decks c. Highly polished and waxed floors

BC POLICY#__1__11/2006

18

2. Remove any spilled liquid from the floor immediately. 3. Good traction helps prevent slipping, wear shoes that provide good traction. 4. NEVER run unless the situation is life-threatening. 5. Take special precautions when working in a location without handrails (i.e., on rooftops and tanktops). 6. Every opening in a deck, a floor, or the ground, and pits which a person could accidentally fall into must be well marked. WALKWAYS 1. All steps, walkways, and stairs MUST be kept free of obstructions and slippery materials, such as oil and grease. 2. When walkways and steps are provided, they MUST be used. DO NOT take shortcuts. 3. Tools, equipment, and materials MUST NOT be left on walkways. 4. Secure hoses and electrical cords to the floor or ground whenever they are laid across walkways. ELECTRICAL SAFETY Personnel shall not be permitted to work in an area where they are likely to encounter electrical hazards unless they have been trained to recognize and avoid the electrical hazards to which they will be exposed. 1. No worker shall approach, and no equipment shall be operated within 10 ft. of live overhead line conductor (50 KV) unless the overhead power line is equipped with conductors that are insulated or covered with insulation material rated for the maximum voltage throughout the area of potential exposure, in which case the minimum clearance shall be 3 feet. 2. Only qualified person, or persons under the direct and continuous supervision of a qualified person shall enter any enclosure containing high voltage equipment where it is possible to come into contact with live high voltage conductors. Enclosures containing high voltage apparatus shall be kept locked. 3. Switch gear must be kept clear of all obstructions and no materials may be stored behind, or on top of this equipment. 4. All spare entries to switches fuse gear, or other equipment must be plugged, or blanked off. All

BC POLICY#__1__11/2006

19

covers, cover bolts, and nuts must be fixed in position and tight. 5. Personnel, when operating electrical equipment, shall follow written or oral instructions. If the equipment does not operate properly, it should be turned off and the supervisor notified. 6. When you are working with or around energized electrical equipment, be sure your hands, feet, and clothing are dry. Isolate yourself from live electrical parts where necessary by using dialectical mats and gloves. 7. Never disconnect the main line switch on a motor while motor is running. Use the proper stopping control. 8. Take care not to overload electrical wiring or equipment. 9. Treat all electrical equipment as energized until determined otherwise. 10. Do not stand directly in front of a switch box when throwing a switch. There may be an unexpected flash. 11. Never use pennies, foil, wire or any other materials in place of proper fusing of electrical circuit. 12. In an emergency when power lines are down, consider every wire including fences and guy wires, live or "hot". Only qualified persons shall handle them. ELECTRICAL SHOCK EMERGENCY 1. Rescuing a victim of electrical injury is dangerous. If you contact the victim, you too could be electrocuted. Do not become second victim! Stop the flow of current to the victim without putting yourself in danger. High voltage current can arc as far as 20 feet. DO NOT TOUCH THE VICTIM WITH BARE HANDS, OR OTHER CONDUCTIVE MATERIAL. 2. Artificial respiration should be applied immediately after a non-breathing victim has been released from the electrical contact, depending on the circumstances of the accident and in regards to the place. 3. In many electrical accidents, the injuries are not from the electric shock but from the effects of burns. They should be treated in accordance with the instructions on first aid. 4. Take the victim to a doctor or emergency room.

BC POLICY#__1__11/2006

20

SUPERVISORY RESPONSIBILITIES Supervisors or other BULLARD COMPANY representatives in charge are responsible for understanding the conditions of the job. They MUST ensure that BULLARD COMPANY employees obey the safety rules. All supervisors must understand that they have a definite responsibility to apply the policies of the safety program in their own departments. The supervisors are expected to accept this responsibility. 1. The supervisor should ensure that all additions, removals, or alterations to BULLARD COMPANY equipment is in accordance with the approved standards and applicable codes. 2. Supervisors should hold daily safety meetings (tailgate/short meetings) when possible and when a new hazard is introduced into the work place. 3. In areas where an inherent hazard exists and cannot be eliminated, the supervisor is responsible for familiarizing the workers with the situation and developing a means of coping with it. 4. Supervisors should inform all employees under their supervision that all accidents of any nature are to be reported immediately. Management MUST be notified immediately in the event of a fatality, serious accident, lost time work injury, or a potential lost work time injury. 5. Supervisor should complete the "Incident Reporting –Observation/Incident/Event" form and follow-up to insure all corrections are made. 6. Supervisors are to maintain a safe working environment by monitoring and enforcing BULLARD COMPANY safety rules and regulations. 7. A supervisor will accompany all injured employees to initial medical treatment in the event of an accident.

BC POLICY#__1__11/2006

21

SECTION 2 PROTECTIVE EQUIPMENT INTRODUCTION Personal protective equipment is vital to safety in your work location. The equipment should be properly cleaned, inspected, and stored in clearly marked and properly designated areas. Any equipment that no longer provides adequate protection should be repaired or replaced immediately. Unusable equipment should be destroyed. EARS 1. Appropriate hearing protection is provided by the Company and MUST be worn by all personal in areas where signs are posted. Hearing protection should also be worn in areas that are suspected of temporary excessive noise, such as where abrasive blasting, grinding or any other loud noise producing activities is in progress. 2. High noise levels MUST be routinely surveyed, and the supervisor should enforce hearing protection where notices are not posted, if noise levels are high. EYES 1. All employees and visitors MUST wear approved safety glasses at all times while on the job site, or in any location where the potential for eye injury exists. 2. Contact lenses DO NOT provide eye protection and are NOT Permitted to be worn in the Shop or any work area. 3. Impact-type goggles MUST be worn and a face shield should be worn when engaging in any activity that involves hazards to the unprotected eye from chipped or flying particles. Some examples are chipping, scrapping, buffing, grinding, etc. 4. Individuals MUST wear splash proof (chemical) goggles when they are handling hazardous chemicals. 5. To ensure maximum protection and comfort, eye protection should be adjusted properly to the face.

BC POLICY#__1__11/2006

22

6. Welding must not be watched without proper eye protection. FEET 1. Approved foot protection must be worn in any field or shop location. Approved foot protection consists of shoes or boots that meet ANSI standard Z41.1. Shoes or boots must have solid outer covering that are highly resistant to water, oil and chemicals and designs that support the ankle is recommended. HANDS 1. Wearing gloves prevent many minor injuries, wear gloves whenever possible. 2. Appropriate gloves MUST be worn when acids are handled. 3. Insulated or heat resistant gloves MUST be worn when regular gloves are not adequate. 4. Refer to the material safety data sheet (MSDS) to determine the type of glove required for each chemical. RESPIRATORY 1. Employees MUST be taught how to use respiratory protection before its actual use is required. Training MUST be conducted in accordance with applicable regulations. 2. Respirators MUST be worn when personnel are working in an atmosphere contaminated with harmful mists, gases, smoke, sprays, and vapors. Respirators must be one of the following types approved by the National Institute of Occupational safety and health (NIOSH): a. Dust Respirators--Used to protect from nuisance and toxic dusts. Not to be used for vapors, mists or fumes unless specified by the manufacture. b. Chemical cartridge respirators--Used to protect from mist or vapor such as paint spray. c. Supplied air blasting hoods--Used in all abrasive blasting operation. d. Self-Contained Breathing Apparatus (SCBA)-- For use in high concentrations of toxic gases, in oxygen deficient atmospheres, or in any environment considered immediately hazardous to life.

BC POLICY#__1__11/2006

23

3. Respirators MUST be cleaned and disinfected and properly stored after each use. 4. Connections on airlines which supply breathing air to hoods MUST be inspected frequently and maintained to ensure their integrity. 5. Any employee working in an area where routine or emergency use of a self-contained breathing apparatus is required to perform his job MUST be clean shaven in the face-piece sealing area and MUST NOT have facial hair that could interfere with the function of the mask. 6. The wearing of prescription glasses and contacts with a respirator is NOT PERMITTED (only special fitted for respirators). 7. Refer to BULLARD COMPANY Respiratory Protection Program for additional information. FALL PROTECTION Fall protection is required if personnel are working at heights greater than six (6) feet and the potential for a fall exists. Personal are not required to use fall protection if: a) The work surface is protected by guardrails. b) Temporary scaffolding and walking surfaces are protected by guardrails. c) Working from portable and fixed ladders less than 20 feet. d) Working from fixed ladders over 20 feet that are caged. When using a fall arrest systems and body harness: a) Before using, inspect the full safety harness for excessive wear or damage that could cause failure. Defective components shall be removed from service. (Destroy and discard harnesses and lanyards that are worn or damaged.) b) Ensure that the harness fits properly around the chest, under the arms and under the legs. c) Lanyards must be a minimum of 2 inch nylon or equivalent with a maximum length of no more than six (6) feet. The nominal breaking strength shall be at least 6,000 lbs. Lanyards should be equipped with shock absorbers.

BC POLICY#__1__11/2006

24

d) Lifelines must be a minimum of 3/4 inch manila or equivalent rope with a minimum breaking strength of 6,000 lbs. Steel cables are recommended for horizontal anchor lines with a minimum breaking strength of 6,000 lbs or five times the live load. e) Fall arrest system components must be from one manufacturer - do not mix brands. f) Protect components from cuts and abrasions. g) Do not use fall arrest systems and components to hoist materials. h) Fall arrest systems that have experienced impact loading must be immediately removed from service. I) Non-locking snap hooks are prohibited for use as part of a fall arrest system. j) Use a climb-assist system on a fixed ladder that is over 20 feet that is not equipped with a cage.

BC POLICY#__1__11/2006

25

SECTION 3 TOOLS AND EQUIPMENT All tools and equipment will be inspected prior to use. All tools and equipment that needs repairs will be repaired or replaced before they are used. Inspection of tools is a very important part of an employee’s job. LADDERS 1. Ladders MUST be maintained in good condition. When portable ladders are used on hard surfaces, they MUST be equipped with nonskid footing or securely fastened to prevent slipping. The top of the ladder should be secured, or the ladder should be held by another person. The base of the ladder should be placed away from the wall by a distance of one-forth of the working length of the ladder. 2. Check the condition of the ladder before it is used and correct any defects. The combined weight of the employee and load should not exceed the load limit of the ladder. Remove any oil, grease or slippery material from the ladder and from shoes. 3. Ladders MUST NOT be placed in front of doors that open toward the ladder. 4. When climbing or descending a ladder, a person must face the ladder and hold the side rails, not the rungs. 5. When working from a ladder, NEVER extend farther than your arms length can reach. 6. NEVER work on an unsecured ladder in windy conditions. 7. A person can not stand on the top two steps of the spreader on a step ladder. 8. It is a good safety practice for someone to hold or steady a step ladder for someone working near the top. 9. When raising a ladder, make sure it will not contact an electrical line. 10. Extension ladders should properly overlap between sections.

BC POLICY#__1__11/2006

26

11. Ladders MUST NOT be used as scaffold members or for any purpose for which they are not intended. SCAFFOLDING OSHA 1910.28 states rules for scaffolding. 1. Any scaffold parts damaged or weakened from any cause shall be immediately repaired and shall not be used until repairs are made. 2. Footing and anchorage for scaffolds shall be sound, rigid, and capable of carrying the maximum intended load without settling or displacement. Unstable objects such as barrels, boxes, loose bricks, or concrete blocks shall not be used to support scaffolds or planks. 3. Scaffold structure shall be capable of handling 4 times the maximum load. Do not exceed scaffold load limits. 4. Employees shall not work on scaffolds during high winds. 5. Do not work on scaffold covered with ice or snow unless all ice and snow is removed. 6. Tools, materials, and trash shall not be allowed to accumulate and cause a hazard. 7. Guardrails not less than 2" X 4" wood or manufactured guardrails will be placed between 36" and 42" from planks. Midrail of 1" by 4" lumber or better will be provided between the guardrails and the planks. Toeboards of a minimum of 4" in height will be installed on all scaffolds above 10 feet in height. 8. Inspect scaffold each day to make sure it is safe before use. 9. Scaffold must be level and plumb at all times. 10. Do not use cross braces to climb scaffold. POWER TOOLS 1. Wear the required Personal Protective Equipment (PPE). 2. Do not operate tools or machines unless all guards are in place. 3. Before repairing, servicing, or changing components on any power tool, the power source MUST

BC POLICY#__1__11/2006

27

be disconnected. 4. When there is a danger of fire or explosion, air-operated tools MUST be used. Combustible gas MUST NOT be used to operate air-powered tools. 5. Hand held power tools MUST be equipped with a switch that is manually held in the on position. 6. Tools with guards must be adjusted so the guard (rest) is 1/8 inch from the wheel. 7. Do not exceed the maximum operating speed marked on the wheel. 8. Do not wear loose clothes, ties, jewelry or gloves that could get caught in the machinery. Keep body parts and clothes away from the point of operations. 9. Remove damaged power tools from service and tag them until properly repaired. 10. Store tools safely. Place sharp edges away from people. HAND TOOLS 1. Do not use tools with a loose or splintered handles. 2. Do not tape cracked or split handles. 3. Use the right tools for the job (example: using a screwdriver for a chisel). 4. Do not alter tools, equipment, machines or remove guards unless you have permission from your supervisor. All alterations must meet the standard. AIR POWERED EQUIPMENT 1. When using air-operated tools, make certain that the supply pressure does not exceed the working pressure of the tool. 2. All abrasive blast equipment shall be equipped with "dead man" controls. 3. Air hose and connections used for air tools shall be designed for the service for which they are used. 4. Only heavy-duty impact-type sockets shall be used on powered impact wrenches.

BC POLICY#__1__11/2006

28

5. When compressed air is used for parts cleaning purpose, reduce the nozzle pressure to 30 psi. 6. Do not use air hoses for hoisting or lowering tools. 7. Do not use compressed air for cleaning clothes or part of the body. GROUNDING 1. Grounding the frames of portable electric tools and equipment (except U.L - listed double- insulated tools) through either a third wire in the cable containing the circuit conductors or through a separate wire grounded at the source of the current. 2. If outlets supplying power to portable electric tools are used outside or in wet locations, make sure there is a ground fault circuit interruption protection (GFIC). 3. All extension cords MUST be checked before use. If damaged it must be repaired or destroyed. 4. Air compressors and sandblast pots MUST be grounded to the metal surface being blasted. COMPANY VEHICLES SPEED LIMIT IN THE YARD IS 10 MPH. 1. All operators of Company vehicles MUST practice defensive driving when operating those vehicles. 2. All operators of Company vehicles MUST have valid, appropriate driver’s licenses. 3. The certificate of registration and other required documents should be carried in all Company vehicles. 4. All drivers of Company vehicles MUST be familiar with and abide by state, federal and local traffic regulations. 5. Seat belts MUST be worn by all occupants of Company vehicles. 6. Picking up hitchhikers is dangerous and PROHIBITED. 7. Any automotive accident involving a Company owned, rented, or leased vehicle, major or minor, MUST be reported as soon as possible. 8. In the event of an accident, the driver is responsible for stopping and following the proper procedure in investigating the accident.

BC POLICY#__1__11/2006

29

1. Stop immediately; do not move the vehicle until authorized by the police, unless by not moving it, additional accident or injury hazards are involved. 2. If there are personal injuries, get medical attention. 3. Get license number of other vehicles involved. 4. Get name and addresses of every witness. 5. Contact your supervisor as soon as possible. 6. Make no statement about the accident to anyone except proper police authorities. 7. A company accident reporting kit is located in the glove compartment of all Company- owned vehicles which contains appropriate forms. 9. NEVER attempt to perform work or drive when you are impaired by alcohol, medication or illegal drugs. 10. Check oil and tire pressures daily. 11. Keep emergency telephone numbers in the glove compartment. 12. Keep MSDS, of materials that you are using, in your truck at all times.

BC POLICY#__1__11/2006

30

SECTION 4 ABRASIVE BLASTING AND SPRAY PAINTING ABRASIVE BLASTING 1. All abrasive blasting equipment shall be in first-class condition. 2. All air hose and sand blasting hose connections MUST be secured together to prevent them from coming apart. 3. Dead man valves MUST be used in all abrasive blasting operations. 4. Before changing a nozzle or hose, dead man valves MUST be disconnected to prevent them from triggering accidentally. 5. Abrasive blast hose shall be of an approved static- dissipating type. The air compressor, abrasive blast hopper, hose, blast nozzle, scaffolding, and surface being worked on is to be grounded to a common ground. 6. All abrasive blasters MUST wear supplied air positive pressure abrasive blast hoods. Helpers MUST wear approved respirators when around abrasive blasting operations and while moving spent abrasive. 7. Spent abrasive shall be removed daily to prevent tripping or slipping hazards. WARNING - FOR BLASTING SAND DO NOT BREATHE THIS MATERIAL NEVER USE THIS MATERIAL WITHOUT AN AIR-SUPPLIED RESPIRATOR Blasting sands contains fine silica dust. If you breathe in this dust you can suffer severe, irreversible lung damage and death. Some medical reports also link breathing silica dust to crippling arthritis and skin and eye irritation. You must never use this material without having a government-approved respirator. The work area must also be thoroughly ventilated by the use of forced ventilation during and after the use of this material.

BC POLICY#__1__11/2006

31

Prior to use of handling, you are advised to review and thoroughly understand all health precautions outlined in the Material Safety Data Sheet (MSDS) provided to your employer by the supplier of this material. Respirator Protection It is a violation of federal safety laws (OSHA) for employers to require workers to use this material without full respirator protection. The federal laws that apply are: 29CFR 1910.134; 29CFR 1910.100; and 29CFR 1910.94. It is recommended that users of the blast sand use OSHA - approved positive pressure, air-fed breathing hood respirators. The positive pressure will prevent silica dust from being drawn into the respirator. Continue to wear the respirator until all airborne silica dust has been exhausted from the work area. Ventilation Finely divided silica dust is nearly invisible. Work areas must be thoroughly ventilated with forced Ventilation fans sufficient to exhaust all silica dust and provide a complete air exchange every five (5) minutes. Continue ventilation even after sand blasting operations have been completed. Other Protective Equipment Silica dust can also be harmful to our skin and eyes. You need to wear tight goggles, heavy rubber gloves. Clothing should be tight fitting at the cuffs, neck and ankles to prevent to prevent silica dust from contacting you body. Clothing should be regularly washed to prevent dust accumulation. Warning Symptoms and First Aid If you experience shortness of breath, coughing and lung and/or throat irritation these may be early warning signs that silica dust is producing a medical condition such as silicosis. Avoid further contact with the material and see your doctor at once if such symptoms occur (contact your supervisor immediately). Swelling of joints, and joint pain, may signal that the start of arthritis, which is also reported to be aggravated by silica exposure. Again, if such symptoms occur seek immediate medical attention. If eye contact and irritation take place, flush your eyes continuously with clear cold water for at least 15 minutes and then see your doctor for an examination and possible treatment. Safety Notes: Federal safety regulations require that employers train workers in the safe use of abrasive blasting materials and equipment and that they hold periodic safety meetings to assure that safety precautions are being maintained. Silica sand poses a health hazard to employees working around abrasive blasting operations, Supplied air positive pressure hood MUST be worn while abrasive blasting. Cartridge type respirators may be worn while removing spent abrasive as long as supplied air is not being used to blow the spent abrasive.

BC POLICY#__1__11/2006

32

SPRAY PAINTING 1. When applying coating in an enclosed area, adequate ventilation is required to keep combustible vapors down. Air-fed hoods MUST be used while coating in an enclosed area. 2. All painting equipment shall be grounded to a common ground to prevent static electricity. 3. When painting interiors, Supplied air positive pressure respirators MUST be worn. 4. When using airless spray equipment you MUST keep the spray nozzle from coming in contact with any part of the body. At such high pressure paint or any liquid will be injected into the body, causing severe injury or even death. 5. If a hole develops while using airless equipment in the airless hose DO NOT try to stop the flow using your hands or feet, even if they are covered. Shut off the airless pump, and then remove the bad section of hose and clean up area where paint was discharged. 6. A "Hot Work Permit" must be obtained before work is to begin in any hazardous area or where hot work is not normally preformed. Paint fumes are hazardous, ALWAYS wear OSHA approved respirators or supplied air positive pressure hoods when around or while applying paints and coatings. NO SMOKING OR OPEN FLAMES WHILE PAINTING.

BC POLICY#__1__11/2006

33

SECTION 5 WELDING AND CUTTING COMPRESSED AIR Compressed air is extremely dangerous. Under no circumstance should anyone use compressed air to blow dust or foreign particles from their clothes or person. Thirty pounds per square inch (30 PSI) of air pressure or higher may blow foreign particles right through an individual's skin, causing severe body damage. No one under any circumstances should allow anyone else to blow compressed air on another individual. Compressed air and/or oxygen will tend to excite flammable material, and will cause flammable material To ignite spontaneously at a lower temperature than they normally would if the extra air or oxygen were not present. BOTTLE GAS Various types of bottled gases are used within our facility. Since all bottle gases are under extreme high pressure, they are very dangerous. Some of these gases are combustible, such as acetylene. Some gases will promote combustion, such as oxygen. Some gases are inert and will neither burn nor support combustion, such as carbon dioxide, argon, nitrogen and etc. However, all bottled gases should be treated safely because they are extremely dangerous due to the high pressure contained within the bottles. Before using any bottled gases, they should be fitted with the proper regulators and check valves to control the pressure when the gas is released from the bottle. All bottled gas should be stored or used in the upright position and always be secured from falling over. Caps (valve covers) must be on when not in use. Never place an acetylene cylinder in a horizontal position. Any extra or empty bottle gases should be stored and chained in approved racks. DANGER A standard 250 cubic foot cylinder pressurized to 2500 PSIG can, after a cylinder valve is broken off,

BC POLICY#__1__11/2006

34

become a rocket attaining a speed of 34 MPH in 1/10 of a second after venting from the broken cylinder connection. OXYGEN AND ACETYLENE Regulators are provided for oxygen and acetylene. Acetylene regulators, check valves, oxygen pressure gauges are to be used for attaching cutting torch hoses. The threads on the hose connections are different. Remember GREEN HOSE is always connected to the OXYGEN, and RED HOSE is always connected to the ACETYLENE. Care should be taken in handling the hoses and cutting torches to prevent damage to them, thus resulting in leakage of oxygen or acetylene into the air. Always be on the alert for leaks. Cutting torches should be treated in a safe manner, and not dropped or thrown, which could result in damage to the control valves. After use, the cutting torch hand hoses should be coiled up and placed back in their storage position. The cutting torches should be properly maintained and the tips should be inspected prior to use, and replaced or repaired if necessary. Turn off gas bottles when not in use. ******* NEVER USE OXYGEN AS REPLACEMENT FOR COMPRESSED AIR ***** CUTTING EQUIPMENT The proper eye protection must be worn when using manual or automatic torch cutting equipment. The operator should wear long sleeve clothing or arm protection and gloves. Any helpers assigned to this work must be protected in a similar manner. Oxygen and acetylene is not to be used for cleaning purpose, such as blowing dust off clothes or blowing dust or particles away from the cutting area. Never light a cigarette, pipe or cigar with any welding, cutting or burning equipment. Oil or grease must never be used on oxygen, cylinders valves, regulators or hose connections. Do not use a hammer or pipe wrench to open cylinder valves. A proper fitting wrench should be used. Do not allow a jet of oxygen to come in contact with greasy clothes, greasy surface or oil soaked rags Greasy clothes should not be worn when handling oxygen and acetylene cutting equipment. Oxygen and acetylene hoses having leaks must be taken out of service immediately. This also applies to regulators, valves, gauges and torches. Any leaks in oxygen or acetylene system should not be checked with an open flame. A soapy water solution should be used on any suspected connections that may be leaking.

BC POLICY#__1__11/2006

35

BURNING WITH OXYGEN AND ACETYLENE Always wear goggles with side shields while burning. If a gauge or torches leak, or equipment is faulty, report same to your supervisor immediately. This is especially important if the leak is in the gas gauge. Keep tanks as far away a possible from the point where you are burning. When burning above the floor, be sure that your are standing clear of any pieces which may fall off during burning. Burning operations must not be performed on material lying on a concrete floor. The concrete may explode and injury you. Do not drop or bump cylinders. Use a suitable cradle or platform for moving cylinders at all times. The cylinders must be secured in the cradle to prevent them from falling out during moving. Keeps sparks, flames, heat and oil away from cylinders at all times. The top cylinders must be free at all times so there will be no obstruction to quick closing of valves. Use oxygen, acetylene and propane only for the purpose which they were intended. Tampering in any manner with regulators is prohibited. If you discover a leaking propane or acetylene cylinder, take it into the open air at once, and keep it away from all fires. Notify your supervisor at once. Cylinders protecting caps must be kept in place at all times when not in use. Cylinders must always be chained or secured. ARC WELDING All leads to the arc welding machine should be properly installed and secured before use. Any damaged worn leads or connections should be repaired before you use them. If repairs can not be made, and then tag the equipment "DO NOT USE". Proper welding hoods with good lenses should be used by welding operators. Any helpers assisting in welding should also wear proper welding hoods. Prior to welding, all hood lenses should be inspected for cracks and weld slag that would obscure vision. Lenses should be cleaned and replaced as necessary. An electrode or piece of electrode should never be left in the electrode holder when the operator is finished welding. This presents a safety hazard for anyone who might trip over or fall on the electrode protruding from the holder if it is left laying on the equipment or on the floor.

BC POLICY#__1__11/2006

36

Section 6 – First Aid INTRODUCTION The American Red Cross defines first aid as the "immediate and temporary care given the victim of an accident or sudden illness until the services of a physician can be obtained." Effective first aid consists primarily of common sense and a few simple rules. "UNIVERSAL PRECAUTIONS" ALL HUMAN BLOOD AND CERTAIN BODY FLUIDS WILL BE TREATED AS IF KNOWN TO BE INFECTED OR HIV, HBV, AND OTHER BLOODBORNE PATHOGENS. The following conditions require that basic life support procedures be used immediately. a. Severe bleeding - If a large blood vessel is severed, enough blood can be lost in one or two minutes to cause death. b. No breathing/circulation - Death or brain damage can occur in four to six minutes if breathing or circulation is not restored c. Poisoning - Every second counts in preventing further injury. GENERAL 1. The primary objective in first aid is to sustain life by utilizing basic life support techniques to: a. Maintain an air way. b. Maintain breathing. c. Maintain circulation. d. Control breathing e. Treat for shock. f. Get medical treatment for the victim. 2. The first aid provider MUST avoid panic, offer reassurance, inspire confidence, and do no more than necessary until medical help arrives. 3. If there is no dispensary, clinic, or hospital in the near proximity of the work site to treat employees, one or more employees MUST be adequately trained to render first aid. First

BC POLICY#__1__11/2006

37

aid supplies approved by a healthcare professional. SEVERE BLEEDING "UNIVERSAL PRECAUTIONS" ALL HUMAN BLOOD AND CERTAIN BODY FLUIDS WILL BE TREATED AS IF KNOWN TO BE INFECTED OR HIV, HBV, AND OTHER BLOODBORNE PATHOGENS. WITH-THIS-THOUGHT-IN-MIND - ALWAYS WEAR PROTECTIVE EQUIPMENT WHEN GIVING FIRST AID 5. Severe bleeding results from wounds to large vessels. Bleeding MUST be controlled quickly. Don't waste time-- apply direct pressure over the wound? The following procedure should be used in the event of severe bleeding: a. Place a clean pad, handkerchief, or cloth over the wound and press firmly with your hands. If you do not have a cloth or bandage, close the wound with your hand or fingers. b. Apply pressure directly over the wound. c. Hold the pad firmly in place with a bandage, necktie, cloth strip, etc... d. Raise the bleeding part higher than the rest of the body unless bones have been broken. e. Keep the victim lying down. f. Keep the victim warm. Cover the victim with blankets or coats, and put something under the victim when found lying on a cold or damp surface. g. If the victim is conscious and can swallow, and if abdominal injury is not suspected, give plenty of liquids (such as water, tea, or coffee). h. Get medical help. 6. A tourniquet should only be used to treat severe, life threaten bleeding that cannot be controlled by other means. The procedure for applying a tourniquet is as follows: a. Use only a strong, wide piece of cloth. NEVER use wire, rope, twine, or other narrow metals. b. Place the tourniquet immediately above the wound, between the body and the edge of the wound. Some normal skin should be left between the wound and the tourniquet. If the wound is near a joint, place the tourniquet at the closest practical point above the joint. c. Make sure the tourniquet is tight enough to stop bleeding. If possible, attach a card to the victim showing the time and place the tourniquet was applied. d. Once the tourniquet has been applied, the victim should be taken to a medical facility immediately. The tourniquet should only be removed by a physician or medical personnel prepared to control bleeding. e. Experience has shown that a properly applied tourniquet can be left in place for one to two hours without causing further damage to the extremity.

BC POLICY#__1__11/2006

38

NO BREATHING/CIRCULATION 7. A person whose breathing and circulating has stopped will die or suffer brain damage if these functions are not restored in four to six minutes. The initial evaluation of a victim should follow the procedures developed by the American Red Cross for basic life support, called the "ABC evaluation". a. Airway - After assuring yourself that the victim is unconscious, open the airway by tilting the head back. Look into the mouth and remove anything that is blocking or could potentially block the airway. This includes gum, partial plates, and chewing tobacco. b. Breathing - Determine whether the victim has stopped breathing or not. Do this by placing your cheek next to the victim’s nose and mouth to feel an exchange of air. At the same time, watch for any chest movement. c. Circulation - Initially place the tips of two fingers on the larynx (voice box) and slide them gently into the groove between the voice box and the large muscle of the neck. This is the location of the carotid artery where you can feel if the heart is circulating blood. If breathing has ceased, begin mouth to mouth or mouth to nose resuscitation. If circulation has stopped, begin external cardiac massage. When combined, these procedures are known as cardiopulmonary resuscitation (CPR). To be performed effectively, they MUST be learned in a certified course. Although the procedures will be discussed in this section, the discussion is not intended to replace an official course. 8. The following CPR procedure should be performed by a single rescuer after evaluation indicates that breathing and circulation have stopped. a. Deliver two quick breaths using mouth-to-mouth or mouth-to-nose breathing. Do this in such a way that the victim does not have a chance to completely exhale. b. Place the heel of one hand over the lower half of the breastbone and place the other hand on top of the first hand. Keeping the arms straight, deliver a quick downward, piston-like thrust to compress the victim’s chest 11/2 to 2 inches. This procedure compresses the heart between the sternum and the backbone, forcing it to circulate blood the rate of approximately 80 times per minute. c. After 15 compressions, immediately tilt the victim's head back and deliver two quick breaths mouth-to-mouth. d. Repeat the cycle of 15 compressions and two quick breaths until medical help arrives. e. Once a minute, check the carotid artery for a pulse. Do this between compressions and the two breaths.

BC POLICY#__1__11/2006

39

f. If you feel a pulse, deliver one breath every five seconds while ensuring that circulation is still present. If breathing and circulation return, keep close watch over the victim in case these processes are needed again. 9. The following CPR procedure is used if a situation involves two rescuers: a. One person does the ABC evaluation while the other rescuer prepares to deliver external cardiac massage. b. The rescuer who has done the evaluation and found no breathing or circulation delivers two quick breaths by mouth-to-mouth resuscitation. c. When the two breaths are completed, the other rescuer starts delivering compressions at the rate of 60 times per minute. d. After every fifth compression, the first rescuer delivers one breath mouth-to-mouth. The ratio then becomes five compressions to one breath until help arrives of a pulse is restored. 10. NEVER practice CPR procedures on real people. These are violent maneuvers that can injure a person if improperly executed. These procedures are learned in a formal CPR course in which life size mannequins are used for practice. 11. The following conditions can cause breathing and/or circulation to stop: electric shock, inhalation of gas such as H2S, inhalation of smoke, lack of oxygen, heart attack, drowning, or a hard blow to the chest. HEART ATTACK 12. For heart attack victims use the following procedure: a. Do ABC evaluation. Begin CPR if breathing and circulation have ceased. Continue CPR until the vital signs have been restored. b. If breathing and circulation are present, keep calm and reassure the victim. c. Loosen the clothing and help the victim get into a comfortable position (usually halfway between lying and sitting). DO NOT carry or lift the victim more than necessary. Have someone call for medical help. d. DO NOT give the victim any liquids without a doctor's advice. CHOKING 13. DO NOT interfere with a choking victim who can speak cough or breath. However, if the choking continues without lessening, call for medical help. 14. If the victim cannot speak, cough, or breathe, take the following action until medical help arrives:

BC POLICY#__1__11/2006

40

a. For a Conscious Victim: (1) Stand just behind and to the side of the victim, who can be standing or sitting. Support the victim with one hand on the chest. The victim's head should be lowered. Deliver four sharp blows between the shoulder-blades. If this technique does not lessen the choking---- (2) Stand behind the victim, who can be standing or sitting. Wrap your arms around the victims middle just above the navel. Clasp your hands together in a doubled fist and press in and up in quick thrusts. Repeat this maneuver several times. If choking continues, repeat a cycle of four back blows and four quick thrusts until the victim is no longer choking or becomes unconscious. b. For an Unconscious Victim: (1) Place the victim on the ground and deliver rescue breathing. If the victim does not start breathing and it appears that your air is not going into your victim’s lungs---- (2) Roll the victim onto one side, facing you, with the chest against your knee. Then deliver four sharp blows between the shoulder blades. If the victim still does not start breathing---- (3) Roll the victim face up and deliver one or more manual thrusts, place one hand on top of the other, with the heel of the bottom hand in the middle of the abdomen, slightly above the navel and below the rib cage. Press into the victim’s abdomen with a quick upward thrust. DO NOT press to either side. Repeat four times if the victim does not start breathing. Even if breathing begins (4) Clear the airway. a. Hold the victims mouth open with one hand, using your thumb to depress the tongue. b. Make a hook of the middle finger of your other hand, and in a gentle sweeping motion, reach into the victim’s throat and feel for a foreign object that may be blocking the air passage. Repeat the following procedure until the air passage is clear: four abdominal thrusts, probe in the mouth, and try to inflate the lungs. (5) If the object has not been retrieved, but the victim seems all right, take the victim to the doctor anyway. INHALATION OF TOXIC GAS OR SMOKE 15. Remove the victim from the contaminated area. DO NOT enter the contaminated area without respiratory protection. NEVER try to rescue a person by holding your breath and entering the contaminated area. Even with respiratory protection, it is dangerous to enter a contaminated area alone or with out stand-by help. DO NOT try to rescue someone by yourself if you can find help quickly. See rule 36-37 of this section.

BC POLICY#__1__11/2006

41

16. As soon as you have the victim in a safe area, perform the following procedure. a. Perform the ABC evaluation. If breathing and/or circulation has stopped, begin CPR. b. If breathing and circulation are present, keep the victim lying down until medical help arrives. ELECTRIC SHOCK 17. For a victim of electric shock perform the following procedure: a. Throw the switch to turn off the current, or use a dry board or stick to remove the electric contact from the victim. b. Do the ABC evaluation and begin CPR if breathing and or circulation have ceased. c. If the breathing and circulation are present, remain with the victim until medical help arrives. It is important that an individual who has suffered an electric shock be evaluated by a physician, as electric shock can severely injure parts of the body. BURNS Burns can result from extreme temperatures (thermal burn) or from chemicals (chemical burn). Burns are very painful and can be complicated by shock, contamination, and dehydration. EXTENSIVE THERMAL BURN 18. For victim's of extensive thermal burns, use the following procedure: a. Wet the victim's remaining clothing with cool water as quickly as possible to reduce burning. b. Place the cleanest available cloth over all burned areas to keep air away from the burn. Wet the burn with cool or cold water to reduce heat. c. Make the victim lie down. d. Place the victim's head and chest a little lower than the rest of the body, and raise the legs if possible. e. If the victim is conscious and can swallow, give plenty of non-alcoholic liquids to drink (water, tea, soft drink, etc.). f. Obtain the services of a physician as soon as possible. SMALL THERMAL BURN 19. Use the following procedure on victims of small thermal burns: a. Soak a sterile gauze pad of clean cloth in cool or cold water, preferably ice water. Place the cold pad over the burn. b. DO NOT disturb or open blisters. c. If the skin is not broken, immerse the skin in clean, cold water, or apply clean ice to

BC POLICY#__1__11/2006

42

relive the pain. LIQUEFIED PETROLEUM GAS (LPG) or COLD BURN Liquefied Petroleum Gas is composed of ethane, propane, butane, and their isomers. These gases are colorless and flammable. When they are handled or shipped as liquids, they have a vapor pressure of 16 psig or 550 psig at 70 degrees F. They are low in toxicity, slightly anesthetic, and have a mild odor ranging from aromatic to slightly disagreeable. 20. LPG produces injury by freezing, as does dry ice. Simple burns on the skin should be treated by flushing the skin with water. The burn maybe either bandaged or left open. Extensive burns should be examined by a doctor. 21. LPG is most destructive when if gets into the eye. Therefore, safety or chemical goggle should be worn when handling the liquid gas. If liquid LPG hits the eye, flush the eye with large amounts of water and refer the victim to a physician as soon as possible. CHEMICAL BURN OF SKIN 22. Use the following procedure for victim of chemical burn: a. Immediately flush the burn with water. Speed helps reduce the extent of the injury. b. Apply a stream of water to the burn while removing the victim’s clothes. c. Place the cleanest available material over the burn. d. If the burn area is extensive, make the victim lie down. Place the head and chest a little lower than the rest of the body, and raise the legs if possible. Extensive burns should be examined by a doctor. CHEMICAL BURN OF EYE 23. Check the victim's eye for contact lenses. Remove them if they are present. Wash the eyes by plunging the head into a vessel of clean water and having the victim blink rapidly, or by allowing water from a drinking fountain or hose to flow into and flush the eyes. If neither of these procedures can be done immediately pour clean water into the victim's eyes from a drinking cup. It is a good practice to keep an eye wash bottle filled with clean water available for emergency use. If the victim's eyelids will not remain open, get another person to hold the lids open, and wash eyes for 15 minutes. Use only water to wash chemical burns. NEVER use another chemical to flush the burns, because this can increase the extent of the injury. EXPOSURE TO CRUDE PRODUCTS (OIL, GAS, CONDENSATE)

BC POLICY#__1__11/2006

43

24. An individual, overcome by vapors, MUST be removed from exposure immediately. A physician should be called. If breathing is irregular or stopped, administer artificial respiration. 25. If a liquid petroleum product is swallowed, DO NOT induce vomiting. Call a doctor immediately. 26. For skin contact, remove contaminated clothing and wash the skin with soap and water. If the petroleum products splash into the eyes, wash the eyes with clean water for 15 minutes or until irritation subsides. SHOCK Whenever someone suffers from trauma or emotional upset, shock maybe present. Shock MUST be considered as a possible complication of every injury and severe illness. Shock occurs when the circulation to vital organs of the body (especially the brain) slows down. This condition is severe and can be life threatening if it is not corrected. 27. The symptoms of shock include the following: a. Cold, clammy skin b. Shallow breathing c. Rapid pulse d. Victim feels cold; may be shaking e. Weakness f. Confusion or disorientation 28. Shock should be treated as follows: a. Make the victim lie down. b. Keep the airway open. If the victim vomits, turn the head to the side so the neck is arched with the chin pointing down. c. If the victim complains of being cold, use a blanket or coat for cover. d. Increase circulation to the brain by elevating the victim’s legs so that the head is lower than the body. e. Reassure the victim. f. If the victim is conscious and can swallow, administer liquids (water, tea, soft drink, etc.). g. NEVER give the victim alcoholic beverages. h. DO NOT give the victim liquids if you think the abdomen is injured. HEAT EXHAUSTION

BC POLICY#__1__11/2006

44

29. The symptoms of heat exhaustion include the following: a. Pale, cold, clammy skin b. Rapid, weak pulse c. Weakness, headache, or nausea d. Cramps in abdomen or limbs e. Excessive perspiration 30. Heat exhaustion should be treated as follows: a. Move the victim to a cool place in the shade. b. Make the victim lie down so the head is lower than the rest of the body. c. Give the victim water to drink and, if available, stir 1/4 teaspoon of salt into the water. d. Get medical help. HEAT STROKE Heat stroke is life threatening, and immediate measures MUST be taken to cool down the victim and get medical care. 31. The symptoms of heat stroke include the following: a. Flushed, dry, hot skin b. Rapid, strong pulse c. Temperature is well above normal, and skin feels hot to the touch. d. Headache, dizziness, nausea. e. Often the victim is unconscious. 32. Heat stroke should be treated as follows: a. Move the victim to a cool place. b. Treat for shock. c. Cover the entire body with cold water, using either a sponge or a hose. Cover the victim with ice, if it is available. Obtain medical help immediately. d. If the victim is fully conscious and can swallow, administer water, or if available, one quarter teaspoon of salt stirred into the water. e. DO NOT give the victim alcoholic beverages. POISON PLANTS Skin poison can result from contact with poison ivy, poison oak, or poison sumac. 33. Symptoms include itching, redness or blisters on the skin after contact with poison plants.

BC POLICY#__1__11/2006

45

34. To treat contact with poison plants, take the following steps: a. Remove the victims clothing from the affected area. Be careful not to let the clothing drag across unaffected skin. It may be necessary to cut the clothing away from the affected areas. b. Wash the exposed area with mild soap and water. Lather and rinse several times. c. Sponge the affected area gently with rubbing alcohol, if some is available. d. If blisters appear on skin, call a physician. SWALLOWED POISONS It is impossible to cover the hundreds of kinds of poisoning and their respective guidelines for treatment. Professional advice should be obtained as soon as possible. 35. The following treatment applies in most cases: a. Try to identify substance ingested. b. Induce vomiting by putting finger down victim’s throat, unless the substance swallowed is a hydrocarbon. In that case do not induce vomiting as this may aggravate the condition. c. Call a physician, emergency room, or poison control center for advice. If you cannot identify the poison, have the victim drink milk or a solution of milk and raw eggs to coagulate the material. Try again to induce vomiting by forcing the victim to gag. INHALATION OF HYDROGEN SULFIDE (H2S) 36. The toxicity limits for hydrogen sulfide are as follows: a. Up to 10 ppm (1/1,000 of 1 percent) --This amount can be smelled and is safe for 8 hours of exposure. b. Up to 100ppm (1/100 of 1 percent) --This amount may sting the eyes and throat. It kills the sense of smell in 3--15 minutes. c. 500ppm (5/100 of 1 percent) --This amount can cause a loss of balance. It may cause respiratory paralyses in 30--40 minutes. It may require CPR. d. 1,000ppm (1/10 of 1 percent) --This amount may cause instantaneous unconsciousness. It can cause death or permanent brain damage as a result of oxygen deficiency. 37. H2S inhalation should be treated as follows: a. First, be sure rescuers have proper respiration protection before they enter a contaminated area. b. Carry the victim to fresh air immediately. If the victim is breathing, you may not need to do any thing else. c. Perform an ABC evaluation. If the victim is not breathing, begin mouth to mouth

BC POLICY#__1__11/2006

46

resuscitation. If circulation has stopped, commence external cardiac massages. BULLARD COMPANY 2700 Centennial Rd. Toledo, OH 43617 419- 841-8775 Please sign this document after you have read the preceding pages, Statement of Policy and Safety Procedures dated November 2006 and return this page to your supervisor. This document will be signed by every employee of BULLARD COMPANY. If there is something that is not understood, please ask. By signing this document, you are stating that you understand and will follow these safety procedures. This document will become a permanent record in your employee file. Upon termination of employment, if the BULLARD COMPANY Safety Manual is NOT returned to BULLARD COMPANY a $10. charge will be deducted from your final payroll check to replace the manual. You must receive permission from BULLARD COMPANY management before giving information contained within this document to someone other than a BULLARD COMPANY employee. SAFETY MANUAL NUMBER ____________ EMPLOYEE NAME PRINTED _____________________________________ SIGNATURE _________________________________________________ DATE _________________________ SUPERVISOR SIGNATURE __________________________________________

File a signed form in central files.