Bul 1494V Variable Depth 600A Disconnect Switch

Product Information

Bulletin 1494V Variable Depth 600A Disconnect Switch(Cat 1494V-DS600 -- Series D)

Additional Resources:1) Go to http://www.literature.rockwellautomation.com 2) Go to Search. Type in publication number: 42052-183-01

Disconnect Switch Installation (Right hand installation shown. For left hand installation follow similar procedure.)1

Disconnect Handle Installation2Install gasket. Install handle and spring bracket. Install defeater lever.1 2 3

Install disconnect switch.7Overlay template F (600 A) over D . Use template D to locate handle holes on mounting plate. 5

IMPORTANT: Apply grease to O-Ring

to retain into handle groove.

A

HOLD FLUSH

TO INSID

E

OF ENCLOSURE

MEASURE TO

INSID

E OF THE

TOP OF ENCLOSURE

TOP

BOTT

6D

HOLD FLUSH

TO INSID

E

OF ENCLOSUREMEASURE TO

INSID

E OF THE

TOP OF ENCLOSURE

TOP HANDLE H

OLE

BOTTOM HANDLE H

OLE

TAP

E HOLD FLUSH

TO INSID

E

OF ENCLOSURE

MEASURE TO

INSID

E OF THE

TOP OF ENCLOSURE

TOP

BOTT

D

113

2

4

90 - 130 lb-in

8-1/4"

4-1/8"

6-5/8"

15"

2-1/16"

6-1/2"

42052-185-01 (1)

Printed in

U.S.A.

F

Disconnect Switc

h Hole Location Template (6

00A)

RIGHT Hand In

stallatio

n

(Use opposite

side for le

ft hand in

stallatio

n)

Switch M

ounting Holes

Center punch and drill

(4) 9

/32" holes fo

r #5/16-18 th

read

forming (T

AP-TITE) screws provided w

ith switc

h

Center punch

and drill (4) holes

for 5/16-18 thread forming

screws provided with switch.

9/32" Dia.

60 - 80 lb-in

7 - 11 lb-in

ATTENTION: Do not install, configure, operate or maintain this product until you have read the product documentation and the documents in the Additional Resources section for installing, configuring, operating or maintaining

equipment. To get the product documentation go to http://www.literature.rockwellautomation.com or contact your local sales office or Rockwell Automation representative.

ATTENTION: Ne pas installer, configurer, exploiter ou maintenir ce produit tant que vous n’avez pas lu sa documentation et les documents de la rubrique Documents connexes pour l’installation, la configuration, l’exploitation et la

maintenance de l’équipement. Pour obtenir de la documentation, rendez-vous sur le site http://www.literature.rockwellautomation.com ou contactez votre agence commerciale Rockwell Automation locale ou son représentant.

ACHTUNG: Für die Installation, Konfiguration, den Betrieb und die Wartung dieses Produkt lesen Sie sich bitte zunächst die Produktdokumentation sowie die Dokumente im Abschnitt „Weitere Informationen“ durch. Die entsprechende

Produktdokumentation finden Sie unter http://www.literature.rockwellautomation.com oder kontaktieren Sie Ihr lokales Vertriebsbüro bzw. einen Rockwell Automation-Mitarbeiter.

ATENCIÓN: No instale, configure, opere ni mantenga este producto hasta que haya leído la documentación del producto y los documentos en la sección Recursos adicionales para la instalación, configuración, operación o mantenimiento

de equipo. Para conseguir la documentación, diríjase a http://www.literature.rockwellautomation.com o póngase en contacto con su oficina regional de ventas o representante de Rockwell Automation.

ATENÇÃO: Não instale, configure, opere ou mantenha este produto até que você leia a documentação do produto e os documentos na seção Recursos adicionais para a instalação, configuração, operação ou manutenção do

equipamento. Para conseguir a documentação, visite http://www.literature.rockwellautomation.com ou entre em contato con seu escritório de vendas regional ou representante da Rockwell Automation.

ATTENZIONE: Non installare, configurare, attivare o riparare questo prodotto senza avere prima letto la relativa documentazione nonchè i documenti indicati nella sezione Ulteriori Risore riguardanti l’installazione, la configurazione,

l’attivazione o la riparazione dell’apparecchiatura. Per la documentazione sul prodotto visitare il sito http://www.literature.rockwellautomation.com o contattare l’ufficio vendite o il rappresentate Rockwell Automation di zona.

WARNING: To prevent electrical shock, disconnect from power source before installing or servicing. Follow NFPA 70E requirements. Install in suitable enclosure. Keep free from contaminants.

The following procedures are critical to the proper operation of the disconnect handle and switch. Failure to follow these steps can result in damage to the equipment and/or serious injury or death to the operator.

Installation, adjustments, putting into service, use, assembly, disassembly, and maintenance shall be carried out by suitably trained personnel in accordance with applicable code of practice. In case of malfunction or damage,

no attempts at repair should be made. The product should be returned to the manufacturer for repair. Do not dismantle the product.

http://www.literature.rockwellautomation.com



PN-133643DIR 42052-184 (Version 03)

Copyright © 2013 Rockwell Automation, Inc. All Rights Reserved. Printed in USA.

ATTENTION: Check for proper operation.

Go to Installation Instruction Sheet 42052-183-01.Trailer Fuse Block Installation5

3

Connecting Rod Installation4

Cutting Connecting Rod (Cut (2) Connecting Rods; first rod connects the handle to the switch, second rod provides

stiffening for the enclosure flange)

Measure working depth of enclosure. Measure, mark and

cut (2) connecting rods.1 2 Remove burrs.3

N minus 3-3/4"

First rod connects the handle to the switch

Second rod provides stiffening for the enclosure flange

N

EnclosureWorking Depth(Inside Flange of Enclosure toMounting Plate)

MountingPlate

Drive Bar

2

Rotate connecting rod into

drive bar 15 turns.

OPEN

4

3

Pull rod up and verify if

rod is 1/2" away from

touching bottom of

spring bracket. (If not,

rotate rod accordingly)

1/2" Clearance

Connecting

Rod

Hitch Pin

Primary Link

5

6

8

7

Verify that disconnect switch and handle are in "OFF"

position. (Switch blades will show “OPEN”)1

9

10

11 150 - 200 lb-in

Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.

Trademarks not belonging to Rockwell Automation are property of their respective companies.

Publication 1494V-IN103C-EN-E - January 2013

TWO SIDES PRINTEDBODY STOCK BUFF - 20# BOND

BODY INK BLACK

MATERIALNO.

MATERIALFOLD

SIZE

PN-133643 11" W x 8-1/2" H

FLAT

11" W x 17" H

Note: After folding---Printed in (Country where printed)*, instruction sheet SAP numbers and barcodeshould be visible.

* The printing vendor may change the instruction sheet files to show the correct country.

Final Fold

Page Layout

17”11”

PN-133643DIR 42052-184 (Version xx)


8 - 1/2”11”

PN-133643DIR 42052-184 (Version xx)
