BTS3902EV200R014 & V200R015Quick Installation

Issue: 01Date: 2012-4-30

HUAWEI TECHNOLOGIES CO., LTD.

Guide

BTS3902E Exterior and Dimensions

Dimensions without a housing

BTS3902E Installation Options

On a Metal Pole with the Diameter Ranging from 60 mm to 114 mm

On a Wall

1

Dimensions with a housing

On a Metal Pole with the Diameter Ranging from 114 mm to 400 mm

On a Wood Pole with the Diameter Ranging from 200 mm to 400 mm

1 Copyright © Huawei Technologies Co., Ltd. 2013. All rights reserved.

BTS3902E Installation Clearance RequRecommended clearance for installing

a single BTS3902

Recommended clearance for installing two BTS3902E side by side

Recommended clearance for installing two BTS3902E in a vertical line

2

uirementsMinimum clearance for installing a single BTS3902E

Minimum clearance for installing two BTS3902E side by side

Minimum clearance for installing two BTS3902E in a vertical line

2

Dimensions and Installation ClearanceProtection BoxExterior and Dimensions Recommend

clearance

交流防雷盒（选配）的安装场景

On a Metal Pole with the Diameter Ranging from 60 mm to 114 mm

On a Wall

3

e Requirements of AC Surge (Optional) ded installation Minimum installation

clearance

On a Metal Pole with the Diameter Ranging from 114 mm to 400 mm

On a Wood Pole with the Diameter Ranging from 200 mm to 400 mm

3

Installing on a Pole with the1 Installing the angle-adjustable mount

The composing of angle-adjustable mountinLifting eyeAttachment plate Lifting eye

Traction eye

Main mounting bracket

Auxiliary mounting

dhTraction eye

2. Installing the auxiliary mounting bra

双头螺母Double-headed nut

Hoist clamp

•Ensure that the arrow on the auxiliary bracket points up.

2 Installing the BTS3902E

•Tighten the two double-headed nuts synchronously and soand auxiliary brackets are the same.

Upper positioning pin

Lower positioning pin

Put the upper positioning pin through the hole on the ahole on the main mounting bracket.

3 Adjusting the installation angle of th

4

3 Adjusting the installation angle of th

The procedures of adjusting the installation angle

e Diameter of 60 mm to 114 mmting kits

g kits 1. Installing the main mounting bracket

g bracket

double-headed nut

Long bolt

Rubber washerDouble-headed nut

ackets

o that the distances between the two sides of the main

Positioning screw

attachment plate and the lower positioning pin through the

he BTS3902E

4

he BTS3902E

e, see the page 8.

Installing on a Pole with the1 Installing the mounting brackets

Adapting plate(1) Mounting hole group A

Ad

1. Inst( ) g g p(2) Mounting hole group B(3) Mounting hole group C(4) Adapting plate

Mabra

Ada

2. Installing the Hose clamp

Mounting hole group B喉箍 LeHose clamp

2 Installing the BTS3902E

Upper positioning pin

Lower positioning pin

Put the upper positioning pin through the hole on the ahole on the main mounting bracket.

5

3 Adjusting the installation angle of th

The procedures of adjusting the installation angle

e Diameter of 114 mm to 400 mm

ti l t

talling the adapting plate assembly

ain mounting acket

apting plateScrew

Hose clampevel

Positioning screw

attachment plate and the lower positioning pin through the

5

he BTS3902E

e, see the page 8.

Installing a BTS3902E on a 1 Installing the adapting plate assembl

Adapting plate(1) Mounting hole group A

Ada( ) g g p(2) Mounting hole group B(3) Mounting hole group C(4) Adapting plate

Mabra

2 Installing the mounting brackets on t1. Drilling holes and install expansion bolt assembliesp

(1) M10x80 b(2) Nut(3) Spring wa(4) Flat wash(5) Expansio

3 Installing the BTS3902E

Upper positioni

Lower positioning pin

Put the upper positioning pin through the hole on the attac

6

pp p g p ghole on the main mounting bracket.

4 Adjusting the installation angle of thThe procedures of adjusting the installation angle

6

Wallly

apting plateScrew

ain mounting acket

Screw

the Wall2. Fitting the mounting piece onto the expansion boltsp

bolt

asherhern tube

(1) Insulation washer(2) Flat washer( )(3) Spring washer(4) Nut

ng pin Positioning screw

chment plate and the lower positioning pin through the

6

p p g p g

e BTS3902Ee, see the page 8.

6

Installing on a Wood Pole wto 400 mm

1 Installing the adapting plate assembl

Adapting plate(1) Mounting hole group A

Ada( ) g g p(2) Mounting hole group B(3) Mounting hole group C(4) Adapting plate

Mabra

2 Installing the mounting piece

Mounting hole group C

BoltSpacer

C组安装Mountinghole grou

3 Installing the BTS3902EUpper positioning p

Lower positioning pin

Put the upper positioning pin through the hole on the attachole on the main mounting bracket.

7

4 Adjusting the installation angle of thThe procedures of adjusting the installation angle

with the Diameter of 200 mm

ly

apting plateScrew

ain mounting acket

Screw

Nut

Spacer

装孔g up C

pinPositioning screw

chment plate and the lower positioning pin through the

7

e BTS3902Ee, see the page 8.

Adjusting the installation an

•Horizontal angle ±30°, vertical angle ±10°.•If the positioning pin is tightened too hard, the installatiopositioning screw first

1 Adjusting the horizontal angle

positioning screw first.The horizontal angle and vertical angle can be adjusted either from the plan or elevation view.•Ensure that the positioning screws both in the vertical d

2 Adjusting the vertical angle

8

ngle of the BTS3902E

on angle cannot be adjusted. In this case, loosen the

simultaneously. The vertical angle can be determined

irection and horizontal direction have been secured.

P iti iPositioning screw

Positioning screw

8

(Optional) Installing the AC 1 Install an AC surge protection box on

•When the diain. to 4.49 in.)protection box•When the dia(4.49 in. to 15•If the diametesmall, cut the

2 Install an AC surge protection box on1. Marking the anchor 2. Installing angpoints

gbolt

(1) M10x65 bolt(2) Spring washer 10(3) Plastic tube(4) Flat washer 10(5) Expansion tube

3 Install an AC surge protection box on1. Drilling holes 2. Instal

the woo

9

Surge Protection Boxn a pole

ameter of the pole ranges from 60 mm to 114 mm (2.36 ), the hose clamps delivered with the AC surge x is used.ameter of the pole ranges from 114 mm to 400 mm 5.75 in.), the hose clamps purchased locally is used.er of the pole around which the clamp is installed is extra part of the clamp.

n a wall.n expansion 3. Installing the AC p g

Surge Protection Box

n a wood poleling the AC surge protection box on

od pole

9

Installing a PGND Cable1 Installing a PGND Cable without AC S

PGND cable

2 Installing a PGND Cable and Equipoten

External ground ba

g q p

Equipotential cablePGND cable

1

External ground bar

Surge Protection Box

OInstalling an OT terminal in the correct manner

ntial Cable with AC Surge Protection Box

ar

g

Installing an OT terminal in the correct manner

0

Installing the Power Cable o1 Installing a Power Cable without AC S

Power Cable

2 Installing a Power Cable with AC Sur

1.Installing the AC Power Cable

BTS390

Thread-lock sealing nuof the PG connector

PG connector

Waterproof blockBTS390Blue----Brown-Yellow/

2. Installing the BTS3902E Power Cable

External Power CableBTS3902E Power Cable

1

of BTS3902ESurge Protection Box

rge Protection Box

02E Power Cable

External Power CableBrown----LinBiue Nin

Insulation layerClip

ut

02E Power Cable-Nout---Lout/Green ----GND

Biue----NinYellow/Green----GND

e

1

Installing the signal Cable1 Installing an FE/GE Fiber Optic Cable

A fast Ethernet or gigabit Ethernet (FE/GE) cable or fibe

1. Installing the optical module

1. Rst

2 T

2.Preparing the FE/GE Optic Cable

2. Tth

3 I t lli FE/GE O ti C bl

DLC connector

Traction cables

3. Installing FE/GE Optic Cable

Socket

Clamping jaw

1

e

r optic cable must be installed for BTS3902E as required.

Remove the dustproof cap of the optical module and tore it properly for future use.urn the puller of an optical module outwards and inserturn the puller of an optical module outwards and insert

he optical module into the OPT0 port on the BTS3902E.

Inner gasket

1. Sort the optical fibers, remove the dustproof cap from the optical fiber connector, and insert the DLC connector into the optical module.

2. Align the clamping jaw on the inner gasket with the socket of the OPT0 port on the BTS3902E. Insert and fit the clamping jaw into the socket.

3. Push the outer gasket of the round connector upwards and tighten the outer gasket until you hear a click sound.

2

Installing the signal Cable

A fast Ethernet or gigabit Ethernet (FE/GE) cable or fibe

2 Installing an FE/GE Cable

3 (Optional) Installing the Alarm Cable

1

r optic cable must be installed for BTS3902E as required.

DB15 male connector

MON Port

DB15 male connector

3

(Optional) Installing a BTS3

1 Installing the BTS3902E RF jumper

You must install a radio frequency (RF) jumper when a B

1. Installing the BTS3902E RF jumper

Type N connector

2. Wrap the connector of the BTS3902E

绝缘PVCinsulation

Waterproof tapePVCinsulation tape

a. Wrap a layer of PVC insulation tape around the cb. Tightly wrap three layers of waterproof tape aroun

up, the second layer from top down, and the thirdc. Tightly wrap three layers of PVC insulation tape ag y p y p

bottom up, the second layer from top down, and td. Bundle cable ties 3 mm to 5 mm away from the e

• When wrapping waterproof tape, stretch the tape ev• When wrapping insulating tape , do not stretch it.• Wrap each layer of tape around the connector tightly

1

Wrap each layer of tape around the connector tightlyoverlaps more than 50% of the preceding layer.• Ensure that the side with adhesive tape is covered o• When cutting off the cable tie, reserve a surplus leng

3902E RF Jumper

BTS3902E uses an external antenna.

E RF jumper

缘胶带tape

onnector from bottom up. nd the connector, with the first layer from bottom layer from bottom up.

around the connector with the first layer from ythe third layer from bottom up. nd of insulating tape.

enly until it is twice of the original length.

y and neatly and ensure that each layer of tape

4

y and neatly, and ensure that each layer of tape

on the wrapped tape.gth of 3 mm to 5 mm.

(Optional) Installing a Camo1. Moving the upper housing

UpUp

2. Installing the camouflage shell

(1) Camoufla

3. Installing the upper housing

(1) Camoufla(2) Slots(3) Tabs

HU

1

ouflage Shell

pper housingpper housing

age shellage shell

UAWEI TECHNOLOGIES CO., LTD.Huawei Industrial Base Bantian Longgang

Sh h 518129

5

Shenzhen 518129People’s Republic of China

www.huawei.com