BTS3900 Adding New Site Procedure

47 Phạm Viết Chánh, Quận 1, Thành Phố Hồ Chí MinhĐT: (08) 54043375 Fax: (08) 54043376

CÔNG TY CỔ PHẦN VIỄN THÔNG DI ĐỘNG TOÀN CẦU

Process of adding new siteQuy trình khai trạm mới

This documents describes how to add a BTS of the 3900 GSM BTS family in TDM transmission mode for the BSC, and how to configure the site device attributes, cell basic attributes, and TRX attributes.

Page 1


VERSION DOCUMENT

Version document Finished Date Remark

English

CHECKED CONTENT

Writer Checker Approver

Đoàn Thanh Việt

Page 2


CONTENT PageCHECKED CONTENT................................................................................................................2

1 Parameters need when we add new site...............................................................................5

2 Process of adding new site BTS GSM 3900.........................................................................6

2.1 Start the wizard for adding a BTS................................................................................6

2.2 Choose Add Site. A dialog box is displayed, as shown in figure 2.1...........................6

2.3 Click Add Site. A dialog box is displayed, as shown in figure 2.2..............................7

2.4 Set the parameters by referring to table 2.1.................................................................7

2.5 Click OK. A dialog box is displayed, as shown in figure 2.3.......................................7

2.6 Click Next. A dialog box is displayed, as shown in figure 2.4.....................................8

2.7 Select a BTS, and then click Add Cell. A dialog box is displayed, as shown in figure 2.5 ...........................................................................................................................................9

2.8 Set the parameters by referring to table 1.2.................................................................9

2.9 Click OK. A dialog box is displayed, as shown in figure 2.6.......................................9

2.10 Click Next. A dialog box is displayed, as shown in figure 2.7...................................10

2.11 Click Site Attributes. A dialog box is displayed, as shown in figure 2.8..................10

2.12 Add FMU and DEMU at slot 8 and 1 as shown in figure 2.9...................................11

2.13 Right-click in the RRU Topology area and choose Add RXU Chain from the shortcut menu. A dialog box is displayed, as shown in figure 2.10.....................................12

2.14 Set the parameters by referring to table 1.2..............................................................12

2.15 Click OK. A dialog box is displayed, as shown in figure 2.11..................................12

2.16 Right-click the RXU chain...........................................................................................13

2.17 Choose Add RXU > Add DRFU. A dialog box is displayed, as shown in figure 2.12..........................................................................................................................................13

2.18 Set the parameters by referring to table 1.2..............................................................14

2.19 Click OK. The DRFU is added....................................................................................14

2.20 Right-click the DRFU...................................................................................................14

Page 3


2.21 Choose Configure RXU Attributes from the shortcut menu. A dialog box is displayed, as shown in figure 2.13..........................................................................................14

2.22 Click the Configure Site Board Attributes tab to display the tab page, as shown in figure 2.14.................................................................................................................................15

2.23 Set the parameters by referring to table 1.2...........................................................16

2.24 Right-click the DRFU................................................................................................16

2.25 Choose Biding logical TRX from the shortcut menu. A dialog box is displayed, as shown in figure 2.15............................................................................................................16

2.26 Click OK to return to the dialog box shown in figure 2.11...................................16

2.27 Repeat step 2.13 through step 2.26 to configure more DRFUs and TRXs...........16

2.28 Click Next. A dialog box is displayed, as shown in figure 2.16.............................16

2.29 Click Cell Attributes. A dialog box is displayed, as shown in figure 2.17............17

2.30 Set the basic attributes of the cell by referring to table 1.2...................................18

2.31 Click Frequency Config. A dialog box is displayed, as shown in figure 2.18.......19

2.32 Set the Frequency Config of the cell by referring to table 1.2...............................19

2.33 Click TRX config. A dialog box is displayed, as shown in figure 2.19..................19

2.34 Click Channel Attributes tab. A dialog box is displayed, as shown in figure 2.20. ..........................................................................................................................................20

2.35 Click Device Attributes tab. A dialog box is displayed, as shown in figure 2.21.20

2.36 Click Frequency Hopping. A dialog box is displayed, as shown in figure 2.22. . .21

2.37 Set the Frequency Hopping of the cell by referring to table 1.2...........................21

2.38 Click Configure MA group. A dialog box is displayed, as shown in figure 2.23. 21

2.39 Set the HSN of the cell by referring to table 1.2.....................................................22

2.40 Click OK to finish the cell and click Finish. The BTS3900 is configured............22

Page 4


1 Parameters need when we add new site

GEIUB Slot No.

GEIUB Port No.

Physical Position on BM Cabinet

Multiplexing Modes BTS Site Name BTS Type

20 14 1-20-14 2:1 Cau-So-1_KGG BTS3900 GSM

Table 1.1: Abis port planning.

HuaweiCellName Cau-So-11_KGG Cau-So-12_KGG Cau-So-13_KGG

HuaweiBSC(ByLAC) BSC_401H_KGG

HuaweiSiteName Cau-So-1_KGG

GSM900/GSM1800 GSM1800

BTSType BTS3900

MCC 452

MNC 07

HuaweiLAC(DEC) 401

HuaweiCI(DEC) 1381 1382 1383

HuaweiPlanningTRXNo. 4 4 4

NCC 1 1 1

BCC 7 7 7

HuaweiBSIC(NCC-BCC) 17 17 17

BCCH 522 525 528

TCHChannelConfig 563,564,565,566,567,568,569,570,571,572,573,574,575,576,577,578,579,580,581,582,583,584,585,586,587

FHMode RFH RFH RFH

HSN 16 16 16

MAIO 0,6,12 2,8,14 4,10,16SDCCH/8 TIMESLOT 2 2 2

PDCH 1 static PDCH and 2 dynamic PDCH

1 static PDCH and 2 dynamic PDCH

1 static PDCH and 2 dynamic PDCH

Table 1.2: Engineer and radio parameters planning

Page 5


2 Process of adding new site BTS GSM 3900

2.1 Start the wizard for adding a BTS

When adding a BTS for the first time, you can start the wizard for adding a BTS only on the GEIUB/GOIUB in the GMPS or GEPS. On the BSC6000 Local Maintenance Terminal, right-click a GEIUB in the GMPS.

2.2 Choose Add Site. A dialog box is displayed, as shown in figure 2.1

Figure 2.1

Page 6


2.3 Click Add Site. A dialog box is displayed, as shown in figure 2.2

Figure 2.2

2.4 Set the parameters by referring to table 2.1

2.5 Click OK. A dialog box is displayed, as shown in figure 2.3

Page 7


Figure 2.3

2.6 Click Next. A dialog box is displayed, as shown in figure 2.4

Figure 2.4

Page 8


2.7 Select a BTS, and then click Add Cell. A dialog box is displayed, as shown in figure 2.5

Figure 2.5



Figure 2.6

Page 9



Figure 2.7

2.11 Click Site Attributes. A dialog box is displayed, as shown in figure 2.8

Page 10


Figure 2.8

2.12 Add FMU and DEMU at slot 8 and 1 as shown in figure 2.9

Figure 2.9

Page 11


2.13 Right-click in the RRU Topology area and choose Add RXU Chain from the shortcut menu. A dialog box is displayed, as shown in figure 2.10

Figure 2.10



Page 12


Figure 2.11

2.16 Right-click the RXU chain

2.17 Choose Add RXU > Add DRFU. A dialog box is displayed, as shown in figure 2.12

Page 13


Figure 2.12


2.19 Click OK. The DRFU is added

2.20 Right-click the DRFU

2.21 Choose Configure RXU Attributes from the shortcut menu. A dialog box is displayed, as shown in figure 2.13

Page 14


Figure 2.13

2.22 Click the Configure Site Board Attributes tab to display the tab page, as shown in figure 2.14

Figure 2.14

Page 15



2.24 Right-click the DRFU

2.25 Choose Biding logical TRX from the shortcut menu. A dialog box is displayed, as shown in figure 2.15

Figure 2.15

2.26 Click OK to return to the dialog box shown in figure 2.11

2.27 Repeat step 2.13 through step 2.26 to configure more DRFUs and TRXs


Page 16


Figure 2.16

2.29 Click Cell Attributes. A dialog box is displayed, as shown in figure 2.17

Page 17


Figure 2.17

2.30 Set the basic attributes of the cell by referring to table 1.2

Page 18


2.31 Click Frequency Config. A dialog box is displayed, as shown in figure 2.18

Figure 2.18

2.32 Set the Frequency Config of the cell by referring to table 1.2

2.33 Click TRX config. A dialog box is displayed, as shown in figure 2.19

Figure 2.19

Page 19


2.34 Click Channel Attributes tab. A dialog box is displayed, as shown in figure 2.20

Figure 2.20

2.35 Click Device Attributes tab. A dialog box is displayed, as shown in figure 2.21

Figure 2.21

Page 20


2.36 Click Frequency Hopping. A dialog box is displayed, as shown in figure 2.22

Figure 2.22

2.37 Set the Frequency Hopping of the cell by referring to table 1.2

2.38 Click Configure MA group. A dialog box is displayed, as shown in figure 2.23

Figure 2.23

Page 21


2.39 Set the HSN of the cell by referring to table 1.2

2.40 Click OK to finish the cell and click Finish. The BTS3900 is configured

Page 22

Documents

BTS3900 Adding New Site Procedure