BS 103Turbo Product Information 01.04.2014

• Apply up 3mm to 15mm in one pour • Single part, no additives required • Suitable for use over vinyl, timber, chipboard • Foot traffic after 30 minutes • Install coverings after 60-90 minutes • Highly Shrinkage compensated Description For smoothing screeds and a variety of floor surfaces & finishes. The high polymer content makes BS 103 Turbo the ideal choice for preparing a surface prior to the installation of a new floor covering. BS 103 Turbo is suitable for use on all common substrates including; sand/cement screeds, concrete, ceramic, quarry and natural stones, timber, vinyl coverings & under floor heating. Due to the strength of formulation, BS 103 Turbo can be applied to a depth of 3mm to 15mm in one application. . Properties Casein/protein free. Blend of special fondu cement with selected additives, self-levelling, fast setting and drying at any thickness. BS 103 Turbo dries quickly with very low shrinkage tension. Set to foot traffic in approximately 30 minutes. Can be used in very heavy traffic areas including heavy wheeled traffic.

Substrates The substrate must be free from structural defects, sound i.e. of adequate compressive and tensile strength, permanently dry and free from laitance, dust, surface treatments or contamination, which would impair the bond of the BSDL product(s). It may be necessary to mechanically prepare the surface of the substrate by grinding / sanding and vacuuming.

Application Mix by adding powder to water, 6 litres of water to 25kg of BS 103 Turbo. Do not exceed 6 litres of water. Exceeding 6 litres of water per unit will result in polymer bleed and therefore extended drying times and a weakened mix. Mix ideally with an electric paddle until you obtain a lump free mix similar in consistency to single cream. When mixed allow to stand for 1 minutes and stir again before application. Use within 5 – 10 minutes of first mixing. Pour a small quantity onto the prepared surface and trowel down lightly. BS 103 Turbo will start to cure 20-30 minutes after application. The successive laying of coverings is possible after drying (60-90 minutes depending on the ambient temperature and humidity).

BSDL Harpur House

62 Harpur Street Bedford

MK40 2RA 13

EN 13813:2002 CT-C35-F10

Cementitious screed material for use internally in buildings

Reaction to fire NPD Release of corrosive substances

CT

Water permeability NPD Water vapour permeability

NPD

Compressive strength

C35

Flexural strength F10 Wear resistance NPD Sound insulation NPD Sound absorption NPD Thermal resistance NPD Chemical resistance NPD

Technical Information

Colour Beige

Supplied as Powder

Mixing ratio 6 ltrs of clean water to 25kg of powder

Coverage 1.5kg per mm application

Initial setting 20 – 30 minutes

Final setting 24 hours

Set to foot traffic * approx. 40 minutes

Set to covering 60 – 90 minutes

Temperature sensitivity powder

< 5°c

Temperature sensitivity after setting none, suitable for use over underfloor heating

Storage time 6 months under normal conditions Packaging

25 kg paper bags, * The above information applies at normal ambient conditions, e.g. 20 ºC and 55% Relative Humidity.

Health & Safety Read the MSDS sheet before use. Always wear suitable protective clothing, gloves and eye/face protection while using this material. Wash any splashes off immediately with soap and water.

Disposal Do not pour directly into drains. Retain the product for later use, or if beyond shelf life, mix and allow to cure and then dispose of in accordance with local regulations. Dispose of empty packaging in accordance with local regulations, or where appropriate recycle. The information contained herein is general and not intended to be specific to any substrate, project or product system. The information is based on our experience to-date and the results of continuous and careful testing. Varying conditions and methods of use will influence the practical application of this product. The products optimum performance is also dependent upon the professional judgment of the user and their conformity to proper trade practice, relevant standards and codes of practice for installation, which are factors outside of our control.