Cover

BSC6910 GUV100R016C00Parameter ListIssue06Date2014/12/30HUAWEI TECHNOLOGIES CO., LTD.

Copyright Huawei Technologies Co., Ltd. 2014. All rights reserved.No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd.

Trademarks and Permissions and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.All other trademarks and trade names mentioned in this document are the property of their respective holders.

NoticeThe purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS" without warranties, guarantees or representations of any kind, either express or implied.The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute a warranty of any kind, express or implied.

Huawei Technologies Co., Ltd.Address:Huawei Industrial BaseBantian, LonggangShenzhen 518129People's Republic of ChinaWebsite:http://www.huawei.comEmail:support@huawei.com

About This DocumentPurposeThis document describes the MO parameters of BSC6910. For the details about the parameters related to northbound interface interconnection, see the BSC6910 GSM V100R016 Parameter List and BSC6910 UMTS V100R016 Parameter List. Intended AudienceThis document is intended for: Network planners System engineers Field engineers Shift operatorsSite maintainersNetwork operatorsStructureThe following table describes the attributes of each parameter.Parameter AttributeDescriptionMOManaged object of NE.Parameter IDA simple character string used for identifying a parameter.Parameter NameName of a parameter.NENEs on which the parameter is set.MML CommandMan Machine Language (MML) command related to the parameter.MeaningFunction of a parameter, protocol that defines the parameter, whether the parameter is out of use in later versions, and whether the parameter is an advanced parameter. If the parameter will be out of use, a related description beginning with "Disuse statement" will be provided in the parameter meaning. Advanced parameters are not configured through northbound interfaces. To modify these parameters, contact Huawei Customer Service Center for technical support.If parameters meet one of the following conditions, they are treated as advanced parameters:1. Parameters are temporarily introduced in a new feature or a customized feature to achieve optimal network performance. These parameters will have fixed values and will be deleted after the beta test or test at the customized site. 2. Modifications to these parameters have a great impact on network KPIs or performance. Normally, modifications of these parameters are not required for features. To achieve optimal network performance, multiple parameters must be modified because modification of a single parameter has little effect on the network and even may cause accidents, for example, service interruption.IsKeyWhether the parameter is used to identify an MO instance.MandatoryWhether the parameter is mandatory for creating an MO instance. Feature IDID of the feature that uses the parameter.Note: Some common parameters and parameters introduced for internal functions do not have corresponding features.Feature NameName of the feature that uses the parameter.Value TypeType of a parameter value. For example, IP Address Type, Compound Type, Enumeration Type, Interval Type, Bit Field Type, Character String Type, Wildcard Mask Type, Subnet Mask Type, Password Type, Any Type, BCD Number Type.GUI Value RangeRange of the parameter values displayed on the GUI.The value of a string parameter cannot contain the following characters:< > ! ? \ / : ; , = + % * " ' |Two or more percent signs (%) or spaces, +++ (start character of an MML message), or --- END (end character of an MML message)NULL or , which indicates that an attribute of an MML message is nullSpaces at both endsNote: The value of the Directory, File Name, and URL parameters can contain a backslash (\) or slash (/).The value of a password parameter cannot contain the following characters:Symbols ; , = " 'Key characters: two or more % symbols or spaces, +++ (start character of an MML message), or --- END (end character of an MML message)Enumeration Number/BitEnumeration number corresponding to the GUI value of a parameter of the enumeration type, or bit position corresponding to the GUI value of a parameter of the bit field type. N/A is filled if the parameter value is not enumeration type or bit field type.Note: For a parameter of the bit field type, bit position lists only the bits in use. Bits not in use are set to 0 and not described in this document.UnitUnit of a parameter value displayed on the GUI.Actual Value RangeRange of the actual values corresponding to the parameter values displayed on the GUI.Default ValueInitial value assigned by the system for a parameter. For a mandatory parameter, no default value is available. For a bit field parameter, if the value of a sub-parameter is ON, the bit representing the sub-parameter is set to 1; if the value of a sub-parameter is OFF, the bit representing the sub-parameter is set to 0. None indicates that no default value is available.Generally, it is displayed on the configuration window of an ADD command but not displayed on the configuration window of a MOD/RMV/DSP/LST/SET command.Recommended ValueParameter values recommended for different scenarios.Initial Value SourceSource for the initial configuration of a parameter. The initial value source can be:Radio planning (Internal planning): The parameter value comes from the radio network plan, facilitating resource management on the NE.Radio planning (Negotiation with the peer): The parameter value comes from the radio network plan. The NE negotiates this value with the peer device to ensure successful interworking.Transport planning (Internal planning): The parameter value comes from the transport network plan, facilitating resource management on the NE.Transport planning (Negotiation with the peer): The parameter value comes from the transport network plan. The NE negotiates this value with the peer device to ensure successful interworking.Equipment planning: The parameter value comes from the equipment plan.Engineering design: The parameter value comes from the algorithm or function design.Default/recommended value: The parameter value uses the default or recommended value, where the recommended value is preferential. The default/recommended value can be used in most scenarios and adjusted for a specific scenario.N/A: The parameter value is not required.ImpactParameter impact scope.Parameter RelationshipRelationship with other parameters. For example, to use this parameter, you need to set related switches and parameters. AccessWhether a parameter has one of the following properties:Read/Write: The parameter can be added, deleted, or modified. Read Only: The parameter can be added or deleted only. Service Interrupted After ModificationWhether the parameter modification interrupts the ongoing services. One of the following comments is provided:Yes: The modification interrupts the ongoing services. No (And no impact on the UE in idle mode): The modification does not interrupt the ongoing services, and has no impact on the network access of UEs in idle mode. No (Impact on the UE in idle mode): The modification does not interrupt the ongoing services, but affects the network access of UEs in idle mode. N/A: This comment is used when a parameter cannot be modified.Interruption ScopePossible interruption scope.Interruption Duration (min)Possible interruption duration (unit: minute).CautionCautions to be taken during the modification.Validation of ModificationHow this parameter takes effect and whether the equipment needs to be restarted after the modification. The parameter modification does not impact the equipment means that the parameter takes effect immediately after the modification.Impact on Radio Network PerformanceImpact of the parameter on radio network performance.Introduced in VersionProduct version in which the parameter is introduced.AttributeWhether the parameter is a radio parameter, a transport parameter, or an equipment parameter.

Issue 01 (&D)Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd&P

Parameter ListMOParameter IDParameter NameNEMML CommandMeaningIsKeyMandatoryFeature IDFeature NameValue TypeGUI Value RangeEnumeration Number/BitUnitActual Value RangeDefault ValueRecommended ValueInitial Value SourceImpactParameter RelationshipAccessService Interrupted After Modification Interruption ScopeInterruption Duration (min)CautionValidation of ModificationImpact on Radio Network PerformanceIntroduced in VersionAttributeAAL2PATHAAL2PATHTAAL2 Path TypeBSC6910ADD AAL2PATHMOD AAL2PATHService type of carried over the PATH. For R99, only the R99 service can be carried. For HSPA, only the HSPA service can be carried. For SHARE, R99 and HSPA services can be carried at the same time.NOYESWRFD-02130501WRFD-05030104Dedicated Iub Transmission ControlDynamic AAL2 Connections in Iub/IuCS/Iur InterfaceEnumeration TypeR99(R99), HSPA(HSPA), SHARE(SHARE)R99~0, HSPA~1, SHARE~2NoneR99, HSPA, SHARENoneNoneTransport Planning (Internal planning)AAL2 PathNoneRead & WriteNo (And no impact on the UE in idle mode)N/AN/ANoneThe parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportAAL2PATHANIAdjacent Node IDBSC6910ADD AAL2PATHBLK AAL2PATHMOD AAL2PATHRMV AAL2PATHUBL AAL2PATHUniquely identifies an adjacent node. Adjacent nodes are uniquely but not necessarily consecutively numbered within BSC6910.YESYESGBFD-150201GBFD-118601GBFD-118605GBFD-118611WRFD-150244WRFD-05030104WRFD-150243A over IP Based on Dynamic Load BalancingAbis over IPIP QOSAbis IP over E1/T1Iu/Iur IP Transmission Based on Dynamic Load BalanceDynamic AAL2 Connections in Iub/IuCS/Iur InterfaceIub IP Transmission Based on Dynamic Load BalanceInterval Type0~65534N/ANone0~65534NoneNoneTransport Planning (Internal planning)Adjacent node-Configuration constraints:If [ADJNODE:NODET] for the adjacent node corresponding to [AAL2PATH:ANI] is not Iub, [ATMLOGICPORT:RSCMNGMODE] of the ATM logical ports specified by [AAL2PATH:CARRYF], [AAL2PATH:CARRYSN], and [AAL2PATH:CARRYVPN] cannot be EXCLUSIVE.If [ADJNODE:NODET] corresponding to [AAL2PATH:ANI] is Iu-CS, each threshold or bandwidth value in [TRMLOADTH] referenced by [AAL2PATH:TRMLOADTHINDEX] must be 0.[ADJNODE:IsROOTNODE] for the adjacent node corresponding to [AAL2PATH:ANI] must be set to YES.[ADJNODE:TRANST] for the adjacent node corresponding to [AAL2PATH:ANI] cannot be set to IP.Read OnlyN/AN/AN/AN/AN/ANoneBSC6910 V100R015C00TransportAAL2PATHCARRYFBearing subrack No.BSC6910ADD AAL2PATHMOD AAL2PATHSubrack number of bearing the AAL2 path.NOYESWRFD-02130501WRFD-05030104Dedicated Iub Transmission ControlDynamic AAL2 Connections in Iub/IuCS/Iur InterfaceInterval Type0~11N/ANone0~11NoneNoneTransport Planning (Internal planning)AAL2 Path-Configuration constraints:If [ADJNODE:NODET] for the adjacent node corresponding to [AAL2PATH:ANI] is not Iub, [ATMLOGICPORT:RSCMNGMODE] of the ATM logical ports specified by [AAL2PATH:CARRYF], [AAL2PATH:CARRYSN], and [AAL2PATH:CARRYVPN] cannot be EXCLUSIVE.-Parameter relationship with conditions:This parameter is valid only when [AAL2PATH:CARRYT] is set to IMA, UNI, NCOPT, FRAATM, ATMLOGICPORT.This parameter must be set when [AAL2PATH:CARRYT] is set to IMA, UNI, NCOPT, FRAATM, ATMLOGICPORT.The parameter will be set with NULL when it is invalid.Read & WriteYesAAL2 PathLess than 5 minutesNoneThe parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportAAL2PATHCARRYFRAATMLNKNBearing FRAATM link No.BSC6910ADD AAL2PATHMOD AAL2PATHNumber of the bearer FRAATM(Fractional ATM) link. The parameter is valid only when the " bearer type " is set to FRAATM. The bearing FRAATM link must be configured already.NOYESWRFD-02130501WRFD-05030104Dedicated Iub Transmission ControlDynamic AAL2 Connections in Iub/IuCS/Iur InterfaceInterval Type0~31N/ANone0~31NoneNoneTransport Planning (Internal planning)AAL2 Path-Parameter relationship with conditions:This parameter is valid only when [AAL2PATH:CARRYT] is set to FRAATM.This parameter must be set when [AAL2PATH:CARRYT] is set to FRAATM.The parameter will be set with NULL when it is invalid.Read & WriteYesAAL2 PathLess than 5 minutesThe FRAATM link must be available.The parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportAAL2PATHCARRYIMAGRPNBearing IMA group No.BSC6910ADD AAL2PATHMOD AAL2PATHNumber of the bearer IMA group. The parameter is valid only when the " bearer type " is set to IMA. The bearing IMA group must be configured already.NOYESWRFD-02130501WRFD-05030104Dedicated Iub Transmission ControlDynamic AAL2 Connections in Iub/IuCS/Iur InterfaceInterval Type0~167N/ANone0~167NoneNoneTransport Planning (Internal planning)AAL2 Path-Parameter relationship with conditions:This parameter is valid only when [AAL2PATH:CARRYT] is set to IMA.This parameter must be set when [AAL2PATH:CARRYT] is set to IMA.The parameter will be set with NULL when it is invalid.Read & WriteYesAAL2 PathLess than 5 minutesThe IMA group must be available.The parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportAAL2PATHCARRYNCOPTNBearing NCOPT port No.BSC6910ADD AAL2PATHMOD AAL2PATHNumber of the bearer NCOPT port. The parameter is valid only when the " bearer type " is set to NCOPT.NOYESWRFD-02130501WRFD-05030104Dedicated Iub Transmission ControlDynamic AAL2 Connections in Iub/IuCS/Iur InterfaceInterval Type0~7N/ANone0~7NoneNoneTransport Planning (Internal planning)AAL2 Path-Parameter relationship with conditions:This parameter is valid only when [AAL2PATH:CARRYT] is set to NCOPT.This parameter must be set when [AAL2PATH:CARRYT] is set to NCOPT.The parameter will be set with NULL when it is invalid.Read & WriteYesAAL2 PathLess than 5 minutesThe port must be available.The parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportAAL2PATHCARRYSNBearing slot No.BSC6910ADD AAL2PATHMOD AAL2PATHNumber of the slot bearing the AAL2 link.NOYESWRFD-02130501WRFD-05030104Dedicated Iub Transmission ControlDynamic AAL2 Connections in Iub/IuCS/Iur InterfaceInterval Type0~27N/ANone0~27NoneNoneTransport Planning (Internal planning)AAL2 Path-Configuration constraints:If [ADJNODE:NODET] for the adjacent node corresponding to [AAL2PATH:ANI] is not Iub, [ATMLOGICPORT:RSCMNGMODE] of the ATM logical ports specified by [AAL2PATH:CARRYF], [AAL2PATH:CARRYSN], and [AAL2PATH:CARRYVPN] cannot be EXCLUSIVE.-Parameter relationship with conditions:This parameter is valid only when [AAL2PATH:CARRYT] is set to IMA, UNI, NCOPT, FRAATM, ATMLOGICPORT.This parameter must be set when [AAL2PATH:CARRYT] is set to IMA, UNI, NCOPT, FRAATM, ATMLOGICPORT.The parameter will be set with NULL when it is invalid.Read & WriteYesAAL2 PathLess than 5 minutesNoneThe parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportAAL2PATHCARRYTBearing typeBSC6910ADD AAL2PATHMOD AAL2PATHLower layer link type of bearing the Path.UNI: see"ADD UNILNK";IMA: see"ADD IMALNK";FRAATM: see"ADD FRALNK";NCOPT: see"LST OPT";ATMLOGICPORT: see"ADD ATMLOGICPORT";NULL: used when testing.NOYESWRFD-02130501WRFD-05030104WRFD-150213Dedicated Iub Transmission ControlDynamic AAL2 Connections in Iub/IuCS/Iur InterfaceMOCN Independent Iub Transmission Resource AllocationEnumeration TypeUNI(UNI Link), IMA(IMA Group), FRAATM(FRAATM Link), NCOPT(Optical Port), ATMLOGICPORT(ATM Logical Port), NULL(NULL)UNI~3, IMA~4, FRAATM~5, NCOPT~6, ATMLOGICPORT~7, NULL~255NoneUNI, IMA, FRAATM, NCOPT, ATMLOGICPORT, NULLNoneNoneTransport Planning (Negotiation with the peer)AAL2 PathNoneRead & WriteYesAAL2 PathLess than 5 minutesNoneThe parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportAAL2PATHCARRYUNILNKNBearing UNI link No.BSC6910ADD AAL2PATHMOD AAL2PATHNumber of the bearer UNI link. The parameter is valid only when the " bearer type " is set to UNI. The bearing UNI link must be configured already.NOYESWRFD-02130501WRFD-05030104Dedicated Iub Transmission ControlDynamic AAL2 Connections in Iub/IuCS/Iur InterfaceInterval Type0~335N/ANone0~335NoneNoneTransport Planning (Internal planning)AAL2 Path-Parameter relationship with conditions:This parameter is valid only when [AAL2PATH:CARRYT] is set to UNI.This parameter must be set when [AAL2PATH:CARRYT] is set to UNI.The parameter will be set with NULL when it is invalid.Read & WriteYesAAL2 PathLess than 5 minutesThe UNI link must be available.The parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportAAL2PATHCARRYVPNBearing ATM logic port No.BSC6910ADD AAL2PATHMOD AAL2PATHATM logic port No. of the bearer. The parameter is valid only when the " bearer type " is set to ATMLOGICPORT. The bearing ATM logic port must be configured. The value mapping between interface boards and ATM logic ports are as follows: AOUc: 0~499; UOIc: 0~499. The ATM logic port must be the leaf ATM logic port (the last level ATM logic port).NOYESWRFD-02130501WRFD-05030104Dedicated Iub Transmission ControlDynamic AAL2 Connections in Iub/IuCS/Iur InterfaceInterval Type0~767N/ANone0~767NoneNoneTransport Planning (Internal planning)AAL2 Path-Configuration constraints:If [ADJNODE:NODET] for the adjacent node corresponding to [AAL2PATH:ANI] is not Iub, [ATMLOGICPORT:RSCMNGMODE] of the ATM logical ports specified by [AAL2PATH:CARRYF], [AAL2PATH:CARRYSN], and [AAL2PATH:CARRYVPN] cannot be EXCLUSIVE.-Parameter relationship with conditions:This parameter is valid only when [AAL2PATH:CARRYT] is set to ATMLOGICPORT.This parameter must be set when [AAL2PATH:CARRYT] is set to ATMLOGICPORT.The parameter will be set with NULL when it is invalid.Read & WriteYesAAL2 PathLess than 5 minutesThe ATM logic port after the modification must be available.The parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportAAL2PATHCIDALLOCALGOSWCID Allocation AlgorithmBSC6910ADD AAL2PATHMOD AAL2PATHAlgorithm of CID allocation. If this parameter is set to ALGO1, the BSC6910 allocates the smallest available CID for an AAL2 path whose ownership is local and allocates the biggest available CID for an AAL2 path whose ownership is peer. If this parameter is set to ALGO2, the BSC6910 allocates the available CIDs from 8 to 255 in succession for an AAL2 path whose ownership is local, and then restarts the allocation, starting from 8 again; and the BSC6910 allocates the available CIDs from 255 to 8 in succession for an AAL2 path whose ownership is peer, and then restarts the allocation, starting from 255 again.NONONoneNoneEnumeration TypeALGO1(Allocation Algorithm1), ALGO2(Allocation Algorithm2)ALGO1~0, ALGO2~1NoneALGO1, ALGO2ALGO1(Allocation Algorithm1)ALGO1(Allocation Algorithm1)Transport Planning (Negotiation with the peer)AAL2 PathNoneRead & WriteNo (And no impact on the UE in idle mode)N/AN/ANoneThe parameter modification has no impact on the equipment.N/ABSC6910 V100R015C00TransportAAL2PATHOWNERSHIPAAL2 Path OwnershipBSC6910ADD AAL2PATHMOD AAL2PATHThe ownership of the AAL2 path is local or peer.NONOWRFD-05030104Dynamic AAL2 Connections in Iub/IuCS/Iur InterfaceEnumeration TypePEER(PEER), LOCAL(LOCAL)PEER~0, LOCAL~1NonePEER, LOCALLOCAL(LOCAL)LOCAL(LOCAL)Transport Planning (Negotiation with the peer)AAL2 PathNoneRead & WriteNo (And no impact on the UE in idle mode)N/AN/ANoneThe parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportAAL2PATHPATHIDAAL2 Path IDBSC6910ADD AAL2PATHBLK AAL2PATHMOD AAL2PATHRMV AAL2PATHUBL AAL2PATHID of one AAL2 path between two AAL2 nodes. The PATHID of the same AAL2 path configured between two AAL2 nodes must be the same. The value should not be equal to 0.YESYESWRFD-05030104WRFD-050404WRFD-02130501Dynamic AAL2 Connections in Iub/IuCS/Iur InterfaceATM/IP Dual Stack Node BDedicated Iub Transmission ControlInterval Type1~4294967295N/ANone1~4294967295NoneNoneTransport Planning (Negotiation with the peer)AAL2 PathNoneRead OnlyN/AN/AN/AN/AN/ANoneBSC6910 V100R015C00TransportAAL2PATHREMARKRemarkBSC6910ADD AAL2PATHMOD AAL2PATHPurpose descriptionNONONoneNoneString Type0~255 charactersN/ANone0~255 characters-NoneTransport Planning (Internal planning)BSC6910NoneRead & WriteNo (And no impact on the UE in idle mode)N/AN/ANoneThe parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportAAL2PATHRXTRFXRX traffic record indexBSC6910ADD AAL2PATHMOD AAL2PATHRX traffic record index of the AAL2 Path on the out BSC6910 port (ATM layer PVC traffic). The traffic index is configured in the ATM traffic table (see "LST ATMTRF").NOYESWRFD-050405WRFD-050406WRFD-02130501WRFD-05030104WRFD-05030106WRFD-05030107Overbooking on ATM TransmissionATM QoS Introduction on Hub Node B (Overbooking on Hub Node B Transmission)Dedicated Iub Transmission ControlDynamic AAL2 Connections in Iub/IuCS/Iur InterfaceCall Admission Based on Used AAL2 Path BandwidthCBR, rt-VBR, nrt-VBR, UBR ATM QoS ClassesInterval Type100~1999N/ANone100~1999NoneNoneTransport Planning (Negotiation with the peer)AAL2 Path-Configuration constraints:[ATMTRF] corresponding to [AAL2PATH:TXTRFX] and [AAL2PATH:RXTRFX] must be configured.[ATMTRF:ST] for [ATMTRF] corresponding to [AAL2PATH:TXTRFX] must be the same as that corresponding to [AAL2PATH:RXTRFX].[ATMTRF:ST] for [ATMTRF] corresponding to [AAL2PATH:TXTRFX] and [AAL2PATH:RXTRFX] cannot be set to UBR_PLUS.-Parameter relationship with conditions:This parameter is valid only when [AAL2PATH:CARRYT] is set to IMA, UNI, NCOPT, FRAATM, ATMLOGICPORT.This parameter must be set when [AAL2PATH:CARRYT] is set to IMA, UNI, NCOPT, FRAATM, ATMLOGICPORT.The parameter will be set with NULL when it is invalid.Read & WriteYesAAL2 PathLess than 5 minutesNoneThe parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportAAL2PATHTIMERCUTimer_CU timerBSC6910ADD AAL2PATHMOD AAL2PATHPeriod for the BSC6910 to package the AAL2 downlink packet data into a large package. This improves transmission efficiency and saves bandwidth.NONOWRFD-050301ATM Transmission Introduction PackageInterval Type1~64N/A0.05ms1~641010Default/Recommended ValueAAL2 PathNoneRead & WriteYesAAL2 PathLess than 5 minutesNoneThe parameter modification has no impact on the equipment.The smaller the value, the shorter the delay, and the less the bandwidth usage; the larger the value, the longer the delay, and the more the bandwidth usage.BSC6910 V100R015C00TransportAAL2PATHTRMLOADTHINDEXTRM load threshold indexBSC6910ADD AAL2PATHMOD AAL2PATHIndex of the TRM load threshold. Before setting this parameter, a TRM load threshold table must be configured by running the "ADD TRMLOADTH" command.NONOGBFD-118605WRFD-050405WRFD-050406IP QOSOverbooking on ATM TransmissionATM QoS Introduction on Hub Node B (Overbooking on Hub Node B Transmission)Interval Type0~199N/ANone0~19900Default/Recommended ValueBSC6910-Configuration constraints:If [ADJNODE:NODET] corresponding to [AAL2PATH:ANI] is Iu-CS, each threshold or bandwidth value in [TRMLOADTH] referenced by [AAL2PATH:TRMLOADTHINDEX] must be 0.[TRMLOADTH:TRANST] for [TRMLOADTH] corresponding to [AAL2PATH:TRMLOADTHINDEX] must be set to ATM.Read & WriteNo (And no impact on the UE in idle mode)N/AN/AThe TRM load threshold must be configured already.The parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportAAL2PATHTXTRFXTX traffic record indexBSC6910ADD AAL2PATHMOD AAL2PATHTX traffic record index of the AAL2 Path on the out BSC6910 port (ATM layer PVC traffic). The traffic index is configured in the ATM traffic table (see "LST ATMTRF").NOYESWRFD-050405WRFD-050406WRFD-02130501WRFD-05030104WRFD-05030106WRFD-05030107Overbooking on ATM TransmissionATM QoS Introduction on Hub Node B (Overbooking on Hub Node B Transmission)Dedicated Iub Transmission ControlDynamic AAL2 Connections in Iub/IuCS/Iur InterfaceCall Admission Based on Used AAL2 Path BandwidthCBR, rt-VBR, nrt-VBR, UBR ATM QoS ClassesInterval Type100~1999N/ANone100~1999NoneNoneTransport Planning (Negotiation with the peer)AAL2 Path-Configuration constraints:[ATMTRF] corresponding to [AAL2PATH:TXTRFX] and [AAL2PATH:RXTRFX] must be configured.[ATMTRF:ST] for [ATMTRF] corresponding to [AAL2PATH:TXTRFX] must be the same as that corresponding to [AAL2PATH:RXTRFX].[ATMTRF:ST] for [ATMTRF] corresponding to [AAL2PATH:TXTRFX] and [AAL2PATH:RXTRFX] cannot be set to UBR_PLUS.-Parameter relationship with conditions:This parameter is valid only when [AAL2PATH:CARRYT] is set to IMA, UNI, NCOPT, FRAATM, ATMLOGICPORT.This parameter must be set when [AAL2PATH:CARRYT] is set to IMA, UNI, NCOPT, FRAATM, ATMLOGICPORT.The parameter will be set with NULL when it is invalid.Read & WriteYesAAL2 PathLess than 5 minutesModifying this parameter will interrupt services.The parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportAAL2PATHVCIBearing VCIBSC6910ADD AAL2PATHMOD AAL2PATHVCI of the AAL2 path out BSC6910.NOYESWRFD-02130501WRFD-050404WRFD-050301Dedicated Iub Transmission ControlATM/IP Dual Stack Node BATM Transmission Introduction PackageInterval Type32~65535N/ANone32~65535NoneNoneTransport Planning (Negotiation with the peer)AAL2 Path-Parameter relationship with conditions:This parameter is valid only when [AAL2PATH:CARRYT] is set to IMA, UNI, NCOPT, FRAATM, ATMLOGICPORT.This parameter must be set when [AAL2PATH:CARRYT] is set to IMA, UNI, NCOPT, FRAATM, ATMLOGICPORT.The parameter will be set with NULL when it is invalid.Read & WriteYesAAL2 PathLess than 5 minutesThe configuration data must be the same as that of the peer system.The parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportAAL2PATHVPIBearing VPIBSC6910ADD AAL2PATHMOD AAL2PATHVPI of the AAL2 path out BSC6910. When the AAL2 path is carried on the AOUc board, the value for Bearing VPI ranges from 0 to 255. When the AAL2 path is carried on the UOIc board, the value for Bearing VPI ranges from 0 to 255 if WORKTYPE in the "SET OPT" command is set to "UNI"; the value for Bearing VPI ranges from 0 to 4095 if WORKTYPE in the "SET OPT" command is set to "NNI".NOYESWRFD-02130501WRFD-05030104WRFD-050301WRFD-05030106Dedicated Iub Transmission ControlDynamic AAL2 Connections in Iub/IuCS/Iur InterfaceATM Transmission Introduction PackageCall Admission Based on Used AAL2 Path BandwidthInterval Type0~4095N/ANone0~4095NoneNoneTransport Planning (Negotiation with the peer)AAL2 Path-Parameter relationship with conditions:This parameter is valid only when [AAL2PATH:CARRYT] is set to IMA, UNI, NCOPT, FRAATM, ATMLOGICPORT.This parameter must be set when [AAL2PATH:CARRYT] is set to IMA, UNI, NCOPT, FRAATM, ATMLOGICPORT.The parameter will be set with NULL when it is invalid.Read & WriteYesAAL2 PathLess than 5 minutesThe configuration data must be the same as that of the peer system.The parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportAAL2RTANIAdjacent Node IDBSC6910ADD AAL2RTUniquely identifies an adjacent node. Adjacent nodes are uniquely but not necessarily consecutively numbered within BSC6910.NOYESGBFD-150201GBFD-118601GBFD-118605GBFD-118611WRFD-150244WRFD-05030104WRFD-150243A over IP Based on Dynamic Load BalancingAbis over IPIP QOSAbis IP over E1/T1Iu/Iur IP Transmission Based on Dynamic Load BalanceDynamic AAL2 Connections in Iub/IuCS/Iur InterfaceIub IP Transmission Based on Dynamic Load BalanceInterval Type0~65534N/ANone0~65534NoneNoneTransport Planning (Internal planning)Adjacent node-Configuration constraints:[ADJNODE:TRANST] and [ADJNODE:NODET] for the adjacent node corresponding to [AAL2RT:ANI] cannot be set to IP and IUB, respectively.[ADJNODE:NODET] for the adjacent node corresponding to [AAL2RT:ANI] cannot be set to IUPS.[AAL2RT:NSAP] and [AAL2RT:ANI] for all AAL2RT must be unique.Read OnlyN/AN/AN/AN/AN/ANoneBSC6910 V100R015C00TransportAAL2RTNSAPDestination ATM addressBSC6910ADD AAL2RTATM address of the destination node of the AAL2 route. The value is entered in the hexadecimal format, with the length ranging from 1.5 bytes to 21 bytes (including the 1-byte H' prefix). It is recommended that the initial byte of the ATM address uses H'45 (indicating E.164 address) or H'39 (indicating the DCC address) or H'47 (indicating the ICD address). The ATM address starting with H'45 close to seven and half bytes of the H'45 must be in the BCD code (15-bit digit), A single semi octet 1111 is then added at the end to obtain an integral number of octets. The following is the DSP. When the DSP is all-zero, it is E.164e, for example, 0x45000971500202001F0000000000000000000000. When the DSP is not all zero, it is E.164A. The ATM address is allocated uniquely in the ATM network. The H'45 format is recommended.NOYESWRFD-050301ATM Transmission Introduction PackageInterval Type0~42N/ANone0~4294967295(40 characters in hex format)NoneNoneTransport Planning (Negotiation with the peer)BSC6910-Configuration constraints:[AAL2RT:NSAP] and [AAL2RT:ANI] for all AAL2RT must be unique.Read OnlyN/AN/AN/AN/AN/ANoneBSC6910 V100R015C00TransportAAL2RTOWNERSHIPDestination ATM address ownershipBSC6910ADD AAL2RTMOD AAL2RTWhether " destination ATM node " is the same as the ATM node specified by " adjacent node ID ". When this parameter is set to YES, the adjacent node is directly connected to the BSC6910. When this parameter is set to NO, the adjacent node is not directly connected to the BSC6910.NONOWRFD-050301ATM Transmission Introduction PackageEnumeration TypeNO(ATM_ADDRESS_DOES_NOT_BELONG_TO_THIS_ADJACENT_NODE), YES(ATM_ADDRESS_BELONGS_TO_THIS_ADJACENT_NODE)NO~0, YES~1NoneNO, YESYES(ATM_ADDRESS_BELONGS_TO_THIS_ADJACENT_NODE)YES(ATM_ADDRESS_BELONGS_TO_THIS_ADJACENT_NODE)Engineering DesignBSC6910NoneRead & WriteNo (And no impact on the UE in idle mode)N/AN/AModified according to practical networking.The parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportAAL2RTRTXRoute indexBSC6910ADD AAL2RTMOD AAL2RTRMV AAL2RTRoute logical number.YESNOWRFD-050301ATM Transmission Introduction PackageInterval Type0~4294967295N/ANone0~4294967295NoneNoneTransport Planning (Internal planning)BSC6910NoneRead OnlyN/AN/AN/AN/AN/ANoneBSC6910 V100R015C00TransportAAL2TMRBLOREQTMRBlocking request timerBSC6910SET AAL2TMRThis timer is started when an AAL2 signaling entity sends the peer node a request for blocking an AAL2 path.NONOWRFD-05030104Dynamic AAL2 Connections in Iub/IuCS/Iur InterfaceInterval Type2000~60000N/Ams2000~6000050005000Transport Planning (Negotiation with the peer)AAL2 PathNoneRead & WriteNo (And no impact on the UE in idle mode)N/AN/AThe modification of the timer involves the peer end. For details, see ITU-T Q2630.1 or ITU-T Q2630.2.The parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportAAL2TMRESTINDTMREstablishment indication timerBSC6910SET AAL2TMRAAL2 connection establishment indication timer. This timer is started when an AAL2 signaling entity sends the service user an indication for establishing an AAL2 connection.NONOWRFD-05030104Dynamic AAL2 Connections in Iub/IuCS/Iur InterfaceInterval Type5000~30000N/Ams5000~3000050005000Transport Planning (Negotiation with the peer)AAL2 PathNoneRead & WriteNo (And no impact on the UE in idle mode)N/AN/AThe modification of the timer involves the peer end. For details, see ITU-T Q2630.1 or ITU-T Q2630.2.The parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportAAL2TMRESTREQTMREstablishment request timerBSC6910SET AAL2TMRAAL2 connection establishment request timer. This timer is started when an AAL2 signaling entity sends the peer node a request for establishing an AAL2 connection.NONOWRFD-05030104Dynamic AAL2 Connections in Iub/IuCS/Iur InterfaceInterval Type5000~30000N/Ams5000~3000070007000Transport Planning (Negotiation with the peer)AAL2 PathNoneRead & WriteNo (And no impact on the UE in idle mode)N/AN/AThe modification of the timer involves the peer end. For details, see ITU-T Q2630.1 or ITU-T Q2630.2.The parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportAAL2TMRMODINDTMRAAL2 modifying indication timerBSC6910SET AAL2TMRThis timer is started when an AAL2 signaling entity sends the service user an indication for modifying the bandwidth of an AAL2 path.NONOWRFD-05030104Dynamic AAL2 Connections in Iub/IuCS/Iur InterfaceInterval Type5000~30000N/Ams5000~300001000010000Transport Planning (Negotiation with the peer)AAL2 PathNoneRead & WriteNo (And no impact on the UE in idle mode)N/AN/AThe modification of the timer involves the peer end. For details, see ITU-T Q2630.1 or ITU-T Q2630.2.The parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportAAL2TMRMODREQTMRAAL2 modifying request timerBSC6910SET AAL2TMRThis timer is started when an AAL2 signaling entity sends the peer node a request for modifying the bandwidth of an AAL2 path.NONOWRFD-05030104Dynamic AAL2 Connections in Iub/IuCS/Iur InterfaceInterval Type5000~30000N/Ams5000~300001000010000Transport Planning (Negotiation with the peer)AAL2 PathNoneRead & WriteNo (And no impact on the UE in idle mode)N/AN/AThe modification of the timer involves the peer end. For details, see ITU-T Q2630.1 or ITU-T Q2630.2.The parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportAAL2TMRRELINDTMRRelease indication timerBSC6910SET AAL2TMRThis timer is started when an AAL2 signaling entity sends the peer node an indication for releasing an AAL2 connection.NONOWRFD-05030104Dynamic AAL2 Connections in Iub/IuCS/Iur InterfaceInterval Type2000~60000N/Ams2000~6000030003000Transport Planning (Negotiation with the peer)AAL2 PathNoneRead & WriteNo (And no impact on the UE in idle mode)N/AN/AThe modification of the timer involves the peer end. For details, see ITU-T Q2630.1 or ITU-T Q2630.2.The parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportAAL2TMRRELREQTMRRelease request timerBSC6910SET AAL2TMRThis timer is started when an AAL2 signaling entity sends the peer node a request for releasing an AAL2 connection.NONOWRFD-05030104Dynamic AAL2 Connections in Iub/IuCS/Iur InterfaceInterval Type2000~60000N/Ams2000~6000050005000Transport Planning (Negotiation with the peer)AAL2 PathNoneRead & WriteNo (And no impact on the UE in idle mode)N/AN/AThe modification of the timer involves the peer end. For details, see ITU-T Q2630.1 or ITU-T Q2630.2.The parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportAAL2TMRRESREQTMRReset request timerBSC6910SET AAL2TMRThis timer is started when an AAL2 signaling entity sends the peer node a request for resetting an AAL2 path.NONOWRFD-05030104Dynamic AAL2 Connections in Iub/IuCS/Iur InterfaceInterval Type2000~60000N/Ams2000~6000050005000Transport Planning (Negotiation with the peer)AAL2 PathNoneRead & WriteNo (And no impact on the UE in idle mode)N/AN/AThe modification of the timer involves the peer end. For details, see ITU-T Q2630.1 or ITU-T Q2630.2.The parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportAAL2TMRUBLREQTMRUnblocking request timerBSC6910SET AAL2TMRThis timer is started when an AAL2 signaling entity sends the peer node a request for unblocking an AAL2 path.NONOWRFD-05030104Dynamic AAL2 Connections in Iub/IuCS/Iur InterfaceInterval Type2000~60000N/Ams2000~6000050005000Transport Planning (Negotiation with the peer)AAL2 PathNoneRead & WriteNo (And no impact on the UE in idle mode)N/AN/AThe modification of the timer involves the peer end. For details, see ITU-T Q2630.1 or ITU-T Q2630.2.The parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportABISCPBTSIDBTS IndexBSC6910ADD ABISCPRMV ABISCPIndex of a BTS, which uniquely identifies a BTS under one BSC6910.YESYESGBFD-111202O&M of BTSInterval Type0~7999N/ANone0~7999NoneNoneEquipment PlanningNone-Parameter relationship with conditions:This parameter is valid only when [ABISCP:IDTYPE] is set to BYID.This parameter must be set when [ABISCP:IDTYPE] is set to BYID.The parameter will be set with NULL when it is invalid.-Others:This parameter is valid only if "IDTYPE" is set to BYID.Read OnlyNo (And no impact on the UE in idle mode)N/AN/ANoneN/ANoneBSC6910 V100R015C00TransportABISCPSCTPLNKIDSCTP link IDBSC6910ADD ABISCPRMV ABISCPIdentifier of SCTP link. The identifier must be unique.YESYESGBFD-150201WRFD-050404GBFD-118601GBFD-118611WRFD-150244WRFD-150243A over IP Based on Dynamic Load BalancingATM/IP Dual Stack Node BAbis over IPAbis IP over E1/T1Iu/Iur IP Transmission Based on Dynamic Load BalanceIub IP Transmission Based on Dynamic Load BalanceInterval Type0~4294967294N/ANone0~4294967294NoneNoneTransport Planning (Internal planning)SCTP linkNoneRead OnlyN/AN/AN/AN/AN/ANoneBSC6910 V100R015C00TransportACADDRACINDEXAC IndexBSC6910ADD ACADDRMOD ACADDRRMV ACADDRIndex of an AP controller (AC) server, which uniquely identifies an AC serverYESYESNoneNoneInterval Type0~49N/ANone0~49NoneNoneEquipment PlanningBSCNoneRead OnlyNo (And no impact on the UE in idle mode)N/AN/ANoneThe parameter modification has no impact on the equipment.NoneBSC6910 V100R016C00RadioACADDRACIPAC IP AddressBSC6910ADD ACADDRMOD ACADDRIP address of the AC serverNOYESNoneNoneIP Address TypeValid IP AddressN/ANoneValid IP AddressNoneNoneTransport Planning (Negotiation with the peer)BSCNoneRead & WriteNo (And no impact on the UE in idle mode)N/AN/ANoneThe parameter modification has no impact on the equipment.NoneBSC6910 V100R016C00RadioACADDRACPORTAC Port No.BSC6910ADD ACADDRMOD ACADDRNumber of the port on the AC server.Do not set this parameter to port 0 because port 0 is reserved for the BSC.NOYESNoneNoneInterval Type0~65535N/ANone0~65535NoneNoneTransport Planning (Negotiation with the peer)BSCNoneRead & WriteNo (And no impact on the UE in idle mode)N/AN/ANoneThe parameter modification has no impact on the equipment.NoneBSC6910 V100R016C00RadioACADDRBSCIPBSC IP AddressBSC6910ADD ACADDRMOD ACADDRIP address of the BSC for communicating with the AC server.NOYESNoneNoneIP Address TypeValid IP AddressN/ANoneValid IP AddressNoneNoneTransport Planning (Negotiation with the peer)BSCNoneRead & WriteNo (And no impact on the UE in idle mode)N/AN/ANoneThe parameter modification has no impact on the equipment.NoneBSC6910 V100R016C00RadioACADDRBSCPORTBSC Port No.BSC6910ADD ACADDRMOD ACADDRNumber of the port on the BSC for communicating with the AC server.NOYESNoneNoneInterval Type4900~4999N/ANone4900~4999NoneNoneTransport Planning (Negotiation with the peer)BSCNoneRead & WriteNo (And no impact on the UE in idle mode)N/AN/ANoneThe parameter modification has no impact on the equipment.NoneBSC6910 V100R016C00RadioACADDRVAPQRYSWITCHVAP Status Query SwitchBSC6910ADD ACADDRMOD ACADDRWhether to query the virtual AP (VAP) status of a specified AC server.NONONoneNoneEnumeration TypeOFF(Off), ON(On)OFF~0, ON~1NoneOFF, ONON(On)ON(On)Default/Recommended ValueBSCNoneRead & WriteNo (And no impact on the UE in idle mode)N/AN/ANoneThe parameter modification has no impact on the equipment.NoneBSC6910 V100R016C00RadioADJLOGICPORTBINDANIAdjacent Node IDBSC6910ADD ADJLOGICPORTBINDRMV ADJLOGICPORTBINDUniquely identifies an adjacent node. Adjacent nodes are uniquely but not necessarily consecutively numbered within BSC6910.YESYESGBFD-150201GBFD-118601GBFD-118605GBFD-118611WRFD-150244WRFD-05030104WRFD-150243A over IP Based on Dynamic Load BalancingAbis over IPIP QOSAbis IP over E1/T1Iu/Iur IP Transmission Based on Dynamic Load BalanceDynamic AAL2 Connections in Iub/IuCS/Iur InterfaceIub IP Transmission Based on Dynamic Load BalanceInterval Type0~65534N/ANone0~65534NoneNoneTransport Planning (Internal planning)Adjacent node-Configuration constraints:If the service type of [ADJNODE] corresponding to [ADJLOGICPORTBIND:ANI] is 3G, [IPLOGICPORT:RLFWACSW] corresponding to [ADJLOGICPORTBIND:LPN] cannot be set to ON.[IPLOGICPORT] whose [IPLOGICPORT:CARRYT] is set to PPP or MP only if [ADJNODE] corresponding to [ADJLOGICPORTBIND:ANI] is Abis interface.[ADJLOGICPORTBIND] can be configured only if [ADJNODE:TRANST] corresponding to [ADJLOGICPORTBIND:ANI] is set to IP or ATM_IP.The value of [ADJNODE:CNMNGMODE] corresponding to [ADJLOGICPORTBIND:ANI] must be the same as that of [IPLOGICPORT:RSCMNGMODE] corresponding to [ADJLOGICPORTBIND:LPN].If [ADJPPPBIND] has been added to [ADJNODE] corresponding to [ADJLOGICPORTBIND:ANI], the physical port carrying [IPLOGICPORT] corresponding to [ADJLOGICPORTBIND:LPN] must be consistent with [ADJPPPBIND:PPPLNKN] and [ADJPPPBIND:MPGRPN].The value of [IPLOGICPORT:IPADDR] corresponding to [ADJLOGICPORTBIND:LPN] must be the same as that of [IPPOOLIP:IPADDR] for [ADJNODE:IPPOOLINDEX] corresponding to [ADJLOGICPORTBIND:ANI].Read OnlyN/AN/AN/AN/AN/ANoneBSC6910 V100R015C00TransportADJLOGICPORTBINDLPNLogic port No.BSC6910ADD ADJLOGICPORTBINDLogical port number.NOYESNoneNoneInterval Type0~1499N/ANone0~1499NoneNoneTransport Planning (Internal planning)BSC6910-Configuration constraints:If the service type of [ADJNODE] corresponding to [ADJLOGICPORTBIND:ANI] is 3G, [IPLOGICPORT:RLFWACSW] corresponding to [ADJLOGICPORTBIND:LPN] cannot be set to ON.The value of [ADJNODE:CNMNGMODE] corresponding to [ADJLOGICPORTBIND:ANI] must be the same as that of [IPLOGICPORT:RSCMNGMODE] corresponding to [ADJLOGICPORTBIND:LPN].If [ADJPPPBIND] has been added to [ADJNODE] corresponding to [ADJLOGICPORTBIND:ANI], the physical port carrying [IPLOGICPORT] corresponding to [ADJLOGICPORTBIND:LPN] must be consistent with [ADJPPPBIND:PPPLNKN] and [ADJPPPBIND:MPGRPN].The value of [IPLOGICPORT:IPADDR] corresponding to [ADJLOGICPORTBIND:LPN] must be the same as that of [IPPOOLIP:IPADDR] for [ADJNODE:IPPOOLINDEX] corresponding to [ADJLOGICPORTBIND:ANI].[ADJLOGICPORTBIND] can be configured only if [IPLOGICPORT:LPNTYPE] corresponding to [ADJLOGICPORTBIND:LPN] is set to Leaf.Read OnlyN/AN/AN/ANoneN/ANoneBSC6910 V100R015C00TransportADJLOGICPORTBINDSNSlot No.BSC6910ADD ADJLOGICPORTBINDNumber of the slot for running this command.NOYESNoneNoneInterval Type0~27N/ANone0~27NoneNoneEquipment PlanningBSC6910NoneRead OnlyNo (And no impact on the UE in idle mode)N/AN/AN/AN/ANoneBSC6910 V100R015C00TransportADJLOGICPORTBINDSRNSubrack No.BSC6910ADD ADJLOGICPORTBINDNumber of the subrackNOYESMRFD-210301Configuration ManagementInterval Type0~11N/ANone0~11NoneNoneEquipment PlanningBoardNoneRead OnlyNo (And no impact on the UE in idle mode)N/AN/AN/AThe parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportADJMAPANIAdjacent Node IDBSC6910ADD ADJMAPMOD ADJMAPRMV ADJMAPUniquely identifies an adjacent node. Adjacent nodes are uniquely but not necessarily consecutively numbered within BSC6910.YESYESGBFD-150201GBFD-118601GBFD-118605GBFD-118611WRFD-150244WRFD-05030104WRFD-150243A over IP Based on Dynamic Load BalancingAbis over IPIP QOSAbis IP over E1/T1Iu/Iur IP Transmission Based on Dynamic Load BalanceDynamic AAL2 Connections in Iub/IuCS/Iur InterfaceIub IP Transmission Based on Dynamic Load BalanceInterval Type0~65534N/ANone0~65534NoneNoneTransport Planning (Internal planning)Adjacent node-Configuration constraints:If [ADJMAP:ITFT] is set to Iub, [ADJMAP:TRANST] must be the same as [ADJNODE:TRANST] for the adjacent node corresponding to [ADJMAP:ANI].[ADJMAP:ITFT] must be consistent with [ADJNODE:NODET] for the adjacent node corresponding to [ADJMAP:ANI], and must be consistent with [TRMMAP:ITFT] for [TRMMAP] corresponding to [ADJMAP:TMIGLD], [ADJMAP:TMISLV], and [ADJMAP:TMIBRZ].Read OnlyN/AN/AN/AN/AN/ANoneBSC6910 V100R015C00TransportADJMAPCNMNGMODEResource Management ModeBSC6910ADD ADJMAPMOD ADJMAPRMV ADJMAPResource management mode.YESYESGBFD-150201WRFD-150244WRFD-150243WRFD-050424A over IP Based on Dynamic Load BalancingIu/Iur IP Transmission Based on Dynamic Load BalanceIub IP Transmission Based on Dynamic Load BalanceTraffic Priority Mapping onto Transmission ResourcesEnumeration TypeSHARE(SHARE), EXCLUSIVE(EXCLUSIVE)SHARE~0, EXCLUSIVE~1NoneSHARE, EXCLUSIVENoneNoneEngineering DesignAdjacent node-Configuration constraints:[ADJMAP:CNMNGMODE] for the adjacent node whose [ADJMAP:ITFT] is set to Iub must be the same. If [ADJNODE:CNMNGMODE] is set to exclusive, the corresponding [ADJMAP:CNMNGMODE] must be also set to exclusive, and [ADJNODE:CNOPINDEX] must be the same as [ADJMAP:CNOPINDEX].-Parameter relationship with conditions:This parameter is valid only when [ADJMAP:ITFT] is set to IUB.This parameter must be set when [ADJMAP:ITFT] is set to IUB.The parameter will be set with NULL when it is invalid.Read OnlyN/AN/AN/AN/AN/ANoneBSC6910 V100R015C00TransportADJMAPCNOPINDEXCN Operator indexBSC6910ADD ADJMAPMOD ADJMAPRMV ADJMAPOperator index of the resource group.YESYESGBFD-118605WRFD-050424IP QOSTraffic Priority Mapping onto Transmission ResourcesInterval Type0~3N/ANone0~3NoneNoneTransport Planning (Internal planning)Adjacent node-Configuration constraints:[ADJMAP:CNMNGMODE] for the adjacent node whose [ADJMAP:ITFT] is set to Iub must be the same. If [ADJNODE:CNMNGMODE] is set to exclusive, the corresponding [ADJMAP:CNMNGMODE] must be also set to exclusive, and [ADJNODE:CNOPINDEX] must be the same as [ADJMAP:CNOPINDEX].-Parameter relationship with conditions:This parameter is valid only when [ADJMAP:CNMNGMODE] is set to EXCLUSIVE.This parameter must be set when [ADJMAP:CNMNGMODE] is set to EXCLUSIVE.The parameter will be set with NULL when it is invalid.Read OnlyN/AN/AN/AN/AN/ANoneBSC6910 V100R015C00TransportADJMAPFTIFactor table indexBSC6910ADD ADJMAPMOD ADJMAPID of an activity factor table which uniquely identifies an activity factor table (To add an activity factor table, run the "ADD TRMFACTOR" command).NOYESWRFD-02130501GBFD-118605WRFD-050424WRFD-050406Dedicated Iub Transmission ControlIP QOSTraffic Priority Mapping onto Transmission ResourcesATM QoS Introduction on Hub Node B (Overbooking on Hub Node B Transmission)Interval Type0~33N/ANone0~33NoneNoneTransport Planning (Internal planning)Adjacent node-Parameter relationship with conditions:This parameter is valid only when [ADJMAP:ITFT] is set to A, ABIS, IUB, IUCS, IUPS, IUR, IURP, SE.This parameter must be set when [ADJMAP:ITFT] is set to A, ABIS, IUB, IUCS, IUPS, IUR, IURP, SE.The parameter will be set with NULL when it is invalid.-Others:The factor table index is configured by setting the value of [TRMFACTOR:FTI].Read & WriteNo (And no impact on the UE in idle mode)N/AN/AThe FACTORTABLE must be configured.The parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportADJMAPITFTInterface TypeBSC6910ADD ADJMAPMOD ADJMAPRMV ADJMAPType of the adjacent node.NOYESWRFD-050404WRFD-150211WRFD-050408WRFD-02130501GBFD-118605WRFD-05030104WRFD-150212WRFD-050424ATM/IP Dual Stack Node BRNC in Pool Load SharingOverbooking on IP TransmissionDedicated Iub Transmission ControlIP QOSDynamic AAL2 Connections in Iub/IuCS/Iur InterfaceRNC in Pool Node RedundancyTraffic Priority Mapping onto Transmission ResourcesEnumeration TypeIUB(Iub Interface), IUR(Iur Interface), IUCS(Iu-CS Interface), IUPS(Iu-PS Interface), ABIS(Abis Interface), A(A Interface), IURP(Iurp Interface), SE(SE Interface)IUB~0, IUR~1, IUCS~2, IUPS~3, ABIS~4, A~5, IURP~10, SE~14NoneIUB, IUR, IUCS, IUPS, ABIS, A, IURP, SENoneNoneTransport Planning (Internal planning)BSC6910-Configuration constraints:[ADJMAP:CNMNGMODE] for the adjacent node whose [ADJMAP:ITFT] is set to Iub must be the same. If [ADJNODE:CNMNGMODE] is set to exclusive, the corresponding [ADJMAP:CNMNGMODE] must be also set to exclusive, and [ADJNODE:CNOPINDEX] must be the same as [ADJMAP:CNOPINDEX].If [ADJMAP:ITFT] is set to Iub, [ADJMAP:TRANST] must be the same as [ADJNODE:TRANST] for the adjacent node corresponding to [ADJMAP:ANI].[ADJMAP:ITFT] must be consistent with [ADJNODE:NODET] for the adjacent node corresponding to [ADJMAP:ANI], and must be consistent with [TRMMAP:ITFT] for [TRMMAP] corresponding to [ADJMAP:TMIGLD], [ADJMAP:TMISLV], and [ADJMAP:TMIBRZ].Read & WriteN/AN/AN/AN/A.N/ANoneBSC6910 V100R015C00TransportADJMAPTMIBRZBronze user TRMMAP indexBSC6910ADD ADJMAPMOD ADJMAPBronze user TRMMAP index used by the current adjacent node.NOYESWRFD-02130501WRFD-050424WRFD-021305Dedicated Iub Transmission ControlTraffic Priority Mapping onto Transmission ResourcesRAN Sharing Phase 2Interval Type0~163N/ANone0~163NoneNoneTransport Planning (Internal planning)Adjacent node-Configuration constraints:[ADJMAP:ITFT] must be consistent with [ADJNODE:NODET] for the adjacent node corresponding to [ADJMAP:ANI], and must be consistent with [TRMMAP:ITFT] for [TRMMAP] corresponding to [ADJMAP:TMIGLD], [ADJMAP:TMISLV], and [ADJMAP:TMIBRZ].-Parameter relationship with conditions:This parameter is valid only when [ADJMAP:ITFT] is set to IURP, IUPS, IUB, IUCS, IUR.This parameter must be set when [ADJMAP:ITFT] is set to IURP, IUPS, IUB, IUCS, IUR.The parameter will be set with NULL when it is invalid.-Others:The TRMMAP index is configured by setting the value of [TRMMAP:TMI].Read & WriteNo (And no impact on the UE in idle mode)N/AN/AThe TRMMAP must be configured.The parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportADJMAPTMIGLDGold user TRMMAP indexBSC6910ADD ADJMAPMOD ADJMAPGold user TRMMAP index used by the current adjacent node.NOYESWRFD-02130501WRFD-050424WRFD-021305Dedicated Iub Transmission ControlTraffic Priority Mapping onto Transmission ResourcesRAN Sharing Phase 2Interval Type0~163N/ANone0~163NoneNoneTransport Planning (Internal planning)Adjacent node-Configuration constraints:[ADJMAP:ITFT] must be consistent with [ADJNODE:NODET] for the adjacent node corresponding to [ADJMAP:ANI], and must be consistent with [TRMMAP:ITFT] for [TRMMAP] corresponding to [ADJMAP:TMIGLD], [ADJMAP:TMISLV], and [ADJMAP:TMIBRZ].-Parameter relationship with conditions:This parameter is valid only when [ADJMAP:ITFT] is set to A, ABIS, IUB, IUCS, IUPS, IUR, IURP, SE.This parameter must be set when [ADJMAP:ITFT] is set to A, ABIS, IUB, IUCS, IUPS, IUR, IURP, SE.The parameter will be set with NULL when it is invalid.-Others:The TRMMAP index is configured by setting the value of [TRMMAP:TMI].Read & WriteNo (And no impact on the UE in idle mode)N/AN/AThe TRMMAP must be configured.The parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportADJMAPTMISLVSilver user TRMMAP indexBSC6910ADD ADJMAPMOD ADJMAPSilver user TRMMAP index used by the current adjacent node.NOYESWRFD-02130501WRFD-050424WRFD-021305Dedicated Iub Transmission ControlTraffic Priority Mapping onto Transmission ResourcesRAN Sharing Phase 2Interval Type0~163N/ANone0~163NoneNoneTransport Planning (Internal planning)Adjacent node-Configuration constraints:[ADJMAP:ITFT] must be consistent with [ADJNODE:NODET] for the adjacent node corresponding to [ADJMAP:ANI], and must be consistent with [TRMMAP:ITFT] for [TRMMAP] corresponding to [ADJMAP:TMIGLD], [ADJMAP:TMISLV], and [ADJMAP:TMIBRZ].-Parameter relationship with conditions:This parameter is valid only when [ADJMAP:ITFT] is set to IURP, IUPS, IUB, IUCS, IUR.This parameter must be set when [ADJMAP:ITFT] is set to IURP, IUPS, IUB, IUCS, IUR.The parameter will be set with NULL when it is invalid.-Others:The TRMMAP index is configured by setting the value of [TRMMAP:TMI].Read & WriteNo (And no impact on the UE in idle mode)N/AN/AThe TRMMAP must be configured.The parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportADJMAPTRANSTTransport Type of the adjacent node and interface typeBSC6910ADD ADJMAPMOD ADJMAPTransport type of the adjacent node and interface type.NOYESGBFD-118701WRFD-050424WRFD-021305WRFD-02130501RAN SharingTraffic Priority Mapping onto Transmission ResourcesRAN Sharing Phase 2Dedicated Iub Transmission ControlEnumeration TypeATM(ATM), IP(IP), ATM_IP(ATM and IP)ATM~0, IP~1, ATM_IP~2NoneATM, IP, ATM_IPNoneNoneTransport Planning (Internal planning)BSC6910-Configuration constraints:If [ADJMAP:ITFT] is set to Iub, [ADJMAP:TRANST] must be the same as [ADJNODE:TRANST] for the adjacent node corresponding to [ADJMAP:ANI].-Parameter relationship with conditions:This parameter is valid only when [ADJMAP:ITFT] is set to IUB.This parameter must be set when [ADJMAP:ITFT] is set to IUB.The parameter will be set with NULL when it is invalid.Read & WriteNo (And no impact on the UE in idle mode)N/AN/AN/A.N/ANoneBSC6910 V100R015C00TransportADJNODEANIAdjacent Node IDBSC6910ADD ADJNODEMOD ADJNODERMV ADJNODEUniquely identifies an adjacent node. Adjacent nodes are uniquely but not necessarily consecutively numbered within BSC6910.YESYESGBFD-150201GBFD-118601GBFD-118605GBFD-118611WRFD-150244WRFD-05030104WRFD-150243A over IP Based on Dynamic Load BalancingAbis over IPIP QOSAbis IP over E1/T1Iu/Iur IP Transmission Based on Dynamic Load BalanceDynamic AAL2 Connections in Iub/IuCS/Iur InterfaceIub IP Transmission Based on Dynamic Load BalanceInterval Type0~65534N/ANone0~65534NoneNoneTransport Planning (Internal planning)Adjacent nodeNoneRead OnlyN/AN/AN/AN/AN/ANoneBSC6910 V100R015C00TransportADJNODEBTSIDSite IndexBSC6910ADD ADJNODEBTS index of the adjacent node to be added. The parameter is valid only when "Adjacent node type" is set to Abis.NOYESGBFD-118605IP QOSInterval Type0~7999N/ANone0~7999NoneNoneTransport Planning (Internal planning)Adjacent node-Configuration constraints:If [ADJNODE:NODET] specifies an adjacent node for the Abis interface, and if [ADJNODE:BTSID] or [ADJNODE:BTSNAME] is set to the same value for adjacent nodes, [ADJNODE:CNMNGMODE] must be set to the same value for the adjacent nodes.If [ADJNODE:NODET] specifies an adjacent node for the Abis interface, and if [ADJNODE:BTSID] or [ADJNODE:BTSNAME] is set to the same value for adjacent nodes and [ADJNODE:CNMNGMODE] is set to EXCLUSIVE, [ADJNODE:CNOPINDEX] must be set to different values.If [ADJNODE:NODET] specifies an adjacent node for the Abis interface, and if [BTS:BTSTYPE] for the corresponding BTS is not set to EGBTS and [ADJNODE:CNMNGMODE] is set to SHARE, [IPPOOLIP] to be added to [IPPOOL] corresponding to [ADJNODE:IPPOOLINDEX] must be the same as [BTSIP:BSCIP]or [BTSIP:BSCUPIP] for [BTSIP] corresponding to [ADJNODE:BTSID] or [ADJNODE:BTSNAME]. - If [ADJNODE:NODET] specifies an adjacent node for the Abis interface, and if [BTS:BTSTYPE] for the corresponding BTS is not set to EGBTS and [ADJNODE:CNMNGMODE] is set to EXCLUSIVE, [IPPOOLIP] to be added to [IPPOOL] corresponding to [ADJNODE:IPPOOLINDEX] must be the same as [BTSIP:BSCIP] or [BTSIP:BSCUPIP] for [BTSIP] corresponding to [ADJNODE:BTSID] or [ADJNODE:BTSNAME], or [IPPOOLIP] must be the same as [BTSEXTOPIP:BSCUPIP] for [BTSEXTOPIP] corresponding to [ADJNODE:BTSID] or [ADJNODE:BTSNAME].The adjacent node that meets both of the following requirements must be unique: [ADJNODE:BTSID] or [ADJNODE:BTSNAME] is the same, and [ADJNODE:CNMNGMODE] is set to SHARE.If [ADJNODE:NODET] specifies an adjacent node for the Abis interface, [BTS] corresponding to [ADJNODE:BTSID] or [ADJNODE:BTSNAME] must exist.If [ADJNODE:NODET] specifies an adjacent node for the Abis interface, [BTS:SERVICEMODE] for [BTS] corresponding to [ADJNODE:BTSID] or [ADJNODE:BTSNAME] must be set to IP.-Parameter relationship with conditions:This parameter is valid only when [ADJNODE:IDTYPE] is set to BYID.This parameter must be set when [ADJNODE:IDTYPE] is set to BYID.The parameter will be set with NULL when it is invalid.Read OnlyN/AN/AN/AN/A.N/ANoneBSC6910 V100R015C00TransportADJNODECHECKCOUNTPing Check Timeout CountsBSC6910ADD ADJNODEMOD ADJNODENumber of times that the ping check timeout occurs.NONOGBFD-150201WRFD-150244WRFD-150243A over IP Based on Dynamic Load BalancingIu/Iur IP Transmission Based on Dynamic Load BalanceIub IP Transmission Based on Dynamic Load BalanceInterval Type1~5N/ANone1~555Default/Recommended ValueBSC6910-Parameter relationship with conditions:This parameter is valid only when [ADJNODE:PINGSWITCH] is set to ENABLE.The parameter will be set with NULL when it is invalid.Read & WriteNo (And no impact on the UE in idle mode)N/AN/AWhen the network status is poor, the check count should not be too small. Otherwise, the local IP state is affected.The parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportADJNODECNMNGMODEResource Management ModeBSC6910ADD ADJNODEResource management mode.NOYESGBFD-150201WRFD-150244WRFD-150243WRFD-050424A over IP Based on Dynamic Load BalancingIu/Iur IP Transmission Based on Dynamic Load BalanceIub IP Transmission Based on Dynamic Load BalanceTraffic Priority Mapping onto Transmission ResourcesEnumeration TypeSHARE(SHARE), EXCLUSIVE(EXCLUSIVE)SHARE~0, EXCLUSIVE~1NoneSHARE, EXCLUSIVENoneNoneEngineering DesignAdjacent node-Configuration constraints:If [ADJNODE:NODET] specifies an adjacent node for the Abis interface, and if [ADJNODE:BTSID] or [ADJNODE:BTSNAME] is set to the same value for adjacent nodes, [ADJNODE:CNMNGMODE] must be set to the same value for the adjacent nodes.If [ADJNODE:NODET] specifies an adjacent node for the Abis interface, and if [ADJNODE:BTSID] or [ADJNODE:BTSNAME] is set to the same value for adjacent nodes and [ADJNODE:CNMNGMODE] is set to EXCLUSIVE, [ADJNODE:CNOPINDEX] must be set to different values.If [ADJNODE:NODET] specifies an adjacent node for the Abis interface, and if [BTS:BTSTYPE] for the corresponding BTS is not set to EGBTS and [ADJNODE:CNMNGMODE] is set to SHARE, [IPPOOLIP] to be added to [IPPOOL] corresponding to [ADJNODE:IPPOOLINDEX] must be the same as [BTSIP:BSCIP]or [BTSIP:BSCUPIP] for [BTSIP] corresponding to [ADJNODE:BTSID] or [ADJNODE:BTSNAME]. - If [ADJNODE:NODET] specifies an adjacent node for the Abis interface, and if [BTS:BTSTYPE] for the corresponding BTS is not set to EGBTS and [ADJNODE:CNMNGMODE] is set to EXCLUSIVE, [IPPOOLIP] to be added to [IPPOOL] corresponding to [ADJNODE:IPPOOLINDEX] must be the same as [BTSIP:BSCIP] or [BTSIP:BSCUPIP] for [BTSIP] corresponding to [ADJNODE:BTSID] or [ADJNODE:BTSNAME], or [IPPOOLIP] must be the same as [BTSEXTOPIP:BSCUPIP] for [BTSEXTOPIP] corresponding to [ADJNODE:BTSID] or [ADJNODE:BTSNAME].The adjacent node that meets both of the following requirements must be unique: [ADJNODE:BTSID] or [ADJNODE:BTSNAME] is the same, and [ADJNODE:CNMNGMODE] is set to SHARE.If BTS is actived and [BTSIP:RSCMNGMODE] is EXCLUSIVE, there must be a ADJNODE with [ADJNODE:CNMNGMODE] set to [BTSIP:CNOPINDEX]If [ADJNODE:NODET] specifies an adjacent node for the Iu-CS, Iu-PS, or A interface, and if [ADJNODE:CNMNGMODE] is set to EXCLUSIVE, [ADJNODE:NODET] and [ADJNODE:CNOPINDEX] for [ADJNODE] cannot be set to the same value for the adjacent node at the same time.If [ADJNODE:NODET] specifies an adjacent node for the Iu-CS, or Iu-PS interface, and if [ADJNODE:CNMNGMODE] for the adjacent node in transmission pool networking mode is set to SHARE, adjacent nodes with the same [ADJNODE:NODET] cannot be configured in non-transmission pool networking mode.If [ADJNODE:NODET] specifies an adjacent node for the Iu-CS, Iu-PS, or A interface, and if [ADJNODE:CNMNGMODE] is set to SHARE, other adjacent nodes whose [ADJNODE:NODET] is the same as the adjacent node and [ADJNODE:CNMNGMODE] is set to SHARE cannot be configured.If [ADJNODE:NODET] specifies an adjacent node for the Iu-CS, Iu-PS, or A interface, and if [ADJNODE:CNMNGMODE] is set to SHARE, other adjacent nodes whose [ADJNODE:NODET] is the same as the adjacent node and [ADJNODE:CNMNGMODE] is set to EXCLUSIVE cannot be configured.If [ADJNODE:NODET] specifies an adjacent node for the Abis or A interface, and if [ADJNODE:CNMNGMODE] is set to EXCLUSIVE, the GSM operator corresponding to [ADJNODE:CNOPINDEX] must have been configured.If [ADJNODE:NODET] specifies an adjacent node for the Iub interface, and if [ADJNODE:LogicRncId] and [ADJNODE:NODEBID] are set to same values for adjacent notes, [ADJNODE:CNMNGMODE] must be set to the same value for the adjacent nodes.If [ADJNODE:NODET] specifies an adjacent node for the Iub interface and [ADJNODE:LogicRncId], [ADJNODE:NODEBID], and [ADJNODE:IPPOOLINDEX] are set to same values for adjacent nodes, and if [ADJNODE:CNMNGMODE] is set to EXCLUSIVE, [ADJNODE:CNOPINDEX] must be set to the same value for the adjacent nodes.If [ADJNODE:NODET] specifies an adjacent node for the Iu-CS or Iu-PS interface, and if both LogicRnc ShareMode and [ADJNODE:CNMNGMODE] are set to SHARE, only one adjacent node can be configured for interfaces of the same type.If [ADJNODE:NODET] specifies an adjacent node for the Iu-CS or Iu-PS interface, and if LogicRnc ShareMode is set to EXCLUSIVE but [ADJNODE:CNMNGMODE] is set to SHARE, only one adjacent node can be configured for each valid [ADJNODE:LogicRncId].If [ADJNODE:NODET] specifies an adjacent node for the Iu-CS or Iu-PS interface, and if LogicRnc ShareMode is set to SHARE but [ADJNODE:CNMNGMODE] is set to EXCLUSIVE, only one adjacent node can be configured for each operator index corresponding to this interface type.If [ADJNODE:NODET] specifies an adjacent node for the Iu-CS or Iu-PS interface, and if both LogicRnc ShareMode and [ADJNODE:CNMNGMODE] are set to EXCLUSIVE, only one adjacent node can be configured for each operator corresponding to each valid [ADJNODE:LogicRncId] for this interface type.If [ADJNODE:NODET] specifies an adjacent node for the Iu-CS or Iu-PS interface, and if LogicRnc ShareMode is set to EXCLUSIVE, [ADJNODE:CNMNGMODE] for adjacent nodes with the same [ADJNODE:NODET] and [ADJNODE:LogicRncId] must be set to the same value.1. [BTSIP:RSCMNGMODE] and [ADJNODE:CNMNGMODE] configured for BTS must be consistent. If ADJNODE does not exist, [BTSIP:RSCMNGMODE] can be set to SHARE or EXCLUSIVE.-Parameter relationship with conditions:This parameter is valid if one of the following conditions is met:1.[ADJNODE:TRANST] is set to IP.2.[ADJNODE:NODET] is set to A, ABIS.This parameter must be set if one of the following conditions is met:1.[ADJNODE:TRANST] is set to IP.2.[ADJNODE:NODET] is set to A.The parameter will be set with NULL when it is invalid.The default value of "CNMNGMODE" is SHARE when "NODET" in MO ADJNODE is set to ABIS and SHARE when "TRANST" in MO ADJNODE is set to IP.Read OnlyN/AN/AN/AN/AN/ANoneBSC6910 V100R015C00TransportADJNODECNOPINDEXCN Operator indexBSC6910ADD ADJNODEIndex for the operator corresponding to this adjacent node.NOYESWRFD-050424Traffic Priority Mapping onto Transmission ResourcesInterval Type0~15N/ANone0~15(GSM);0~3(UMTS)NoneNoneTransport Planning (Internal planning)BSC6910-Configuration constraints:If [ADJNODE:NODET] specifies an adjacent node for the Abis interface, and if [ADJNODE:BTSID] or [ADJNODE:BTSNAME] is set to the same value for adjacent nodes and [ADJNODE:CNMNGMODE] is set to EXCLUSIVE, [ADJNODE:CNOPINDEX] must be set to different values.If [ADJNODE:NODET] specifies an adjacent node for the Iu-CS, Iu-PS, or A interface, and if [ADJNODE:CNMNGMODE] is set to EXCLUSIVE, [ADJNODE:NODET] and [ADJNODE:CNOPINDEX] for [ADJNODE] cannot be set to the same value for the adjacent node at the same time.If [ADJNODE:NODET] specifies an adjacent node for the Abis or A interface, and if [ADJNODE:CNMNGMODE] is set to EXCLUSIVE, the GSM operator corresponding to [ADJNODE:CNOPINDEX] must have been configured.If [ADJNODE:NODET] specifies an adjacent node for the Iub interface and [ADJNODE:LogicRncId], [ADJNODE:NODEBID], and [ADJNODE:IPPOOLINDEX] are set to same values for adjacent nodes, and if [ADJNODE:CNMNGMODE] is set to EXCLUSIVE, [ADJNODE:CNOPINDEX] must be set to the same value for the adjacent nodes.-Parameter relationship with conditions:This parameter is valid only when [ADJNODE:CNMNGMODE] is set to EXCLUSIVE.This parameter must be set when [ADJNODE:CNMNGMODE] is set to EXCLUSIVE.The parameter will be set with NULL when it is invalid.Read OnlyN/AN/AN/AN/AN/ANoneBSC6910 V100R015C00TransportADJNODEDPXDPX IndexBSC6910ADD ADJNODEIndex of the Destination Signaling Point (DSP). This parameter is valid when the node type is set to IUR, IUCS, IUPS, or NNI_AAL2SWITCH.NOYESWRFD-010101GBFD-1186053GPP R9 SpecificationsIP QOSInterval Type0~427N/ANone0~427NoneNoneTransport Planning (Internal planning)Adjacent node-Configuration constraints:If the SPX specified by [N7DPC:SPX] for [N7DPC] corresponding to [ADJNODE:DPX] is an assistor signaling point index, the SPX can reference the same DPX as other adjacent nodes but different [ADJNODE:NODET]. If the SPX specified by [N7DPC:SPX] for [N7DPC] corresponding to [ADJNODE:DPX] is not an assistor signaling point index, the DPX cannot be referenced by other adjacent nodes.If [ADJNODE:NODET] specifies an adjacent node for the Iur, Iu-CS, Iu-PS, or NNI_AAL2SWITCH, and if [ADJNODE:DPX] is set to a valid value, [N7DPC:DPCT] for [N7DPC] corresponding to [ADJNODE:DPX] must match [ADJNODE:NODET].-Parameter relationship with conditions:This parameter is valid if one of the following conditions is met:1.[ADJNODE:TRANST] is set to ATM.2.[ADJNODE:NODET] is set to IUR, NNI_AAL2SWITCH.This parameter must be set if one of the following conditions is met:1.[ADJNODE:TRANST] is set to ATM.2.[ADJNODE:NODET] is set to IUR, NNI_AAL2SWITCH.The parameter will be set with NULL when it is invalid.Read OnlyN/AN/AN/AN/AN/ANoneBSC6910 V100R015C00TransportADJNODEDSCPDifferentiated Service CodepointBSC6910ADD ADJNODEMOD ADJNODEDifferentiated Service Codepoint. This parameter is used for setting the priority for the ping packets. The higher the value of this parameter, the higher the priority of the ping packets.NONOGBFD-150201WRFD-150244WRFD-150243A over IP Based on Dynamic Load BalancingIu/Iur IP Transmission Based on Dynamic Load BalanceIub IP Transmission Based on Dynamic Load BalanceInterval Type0~63N/ANone0~634646Default/Recommended ValueAdjacent node-Parameter relationship with conditions:This parameter is valid only when [ADJNODE:PINGSWITCH] is set to ENABLE.The parameter will be set with NULL when it is invalid.Read & WriteNo (And no impact on the UE in idle mode)N/AN/ANoneThe parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportADJNODEENIDExternal Node IdBSC6910ADD ADJNODENode ID of an external physical RNC. Such a node ID identifies a physical RNC in an RNC in Pool network.NOYESWRFD-150212WRFD-150211RNC in Pool Node RedundancyRNC in Pool Load SharingInterval Type0~4095N/ANone0~4095NoneNoneEquipment PlanningNone-Configuration constraints:If [ADJNODE:NODET] specifies an adjacent node for IURP, [EXTNODE] corresponding to [ADJNODE:ENID] must have been configured.If [ADJNODE:NODET] specifies an adjacent node for the IURP, [ADJNODE:ENID] must be set to different values.-Parameter relationship with conditions:This parameter is valid only when [ADJNODE:TRANST] is set to IP.This parameter must be set when [ADJNODE:TRANST] is set to IP.The parameter will be set with NULL when it is invalid.Read OnlyN/AN/AN/AN/AN/AN/A.BSC6910 V100R015C00TransportADJNODEENODEBNAMEeNodeB NameBSC6910ADD ADJNODEName of eNodeB.NOYESNoneNoneString Type1~64 charactersN/ANone1~64 charactersNoneNoneTransport Planning (Internal planning)Transport channel-Parameter relationship with conditions:This parameter is valid only when [ADJNODE:NODET] is set to SE.This parameter must be set when [ADJNODE:NODET] is set to SE.The parameter will be set with NULL when it is invalid.Read OnlyN/AN/AN/AN/A.N/ANoneBSC6910 V100R016C00TransportADJNODEIPPOOLINDEXTransmission Resource Pool IndexBSC6910ADD ADJNODEA Transmission Resource Pool index identifies a Transmission Resource Pool. This index is globally unique.NOYESWRFD-150244WRFD-150243Iu/Iur IP Transmission Based on Dynamic Load BalanceIub IP Transmission Based on Dynamic Load BalanceInterval Type0~255N/ANone0~255NoneNoneTransport Planning (Internal planning)BSC6910-Configuration constraints:If [ADJNODE:NODET] specifies an adjacent node for the Abis interface, only one [IPPOOLIP] can be added to [IPPOOL] corresponding to [ADJNODE:IPPOOLINDEX].If [ADJNODE:NODET] specifies an adjacent node for the Abis interface, and if [BTS:BTSTYPE] for the corresponding BTS is not set to EGBTS and [ADJNODE:CNMNGMODE] is set to SHARE, [IPPOOLIP] to be added to [IPPOOL] corresponding to [ADJNODE:IPPOOLINDEX] must be the same as [BTSIP:BSCIP]or [BTSIP:BSCUPIP] for [BTSIP] corresponding to [ADJNODE:BTSID] or [ADJNODE:BTSNAME]. - If [ADJNODE:NODET] specifies an adjacent node for the Abis interface, and if [BTS:BTSTYPE] for the corresponding BTS is not set to EGBTS and [ADJNODE:CNMNGMODE] is set to EXCLUSIVE, [IPPOOLIP] to be added to [IPPOOL] corresponding to [ADJNODE:IPPOOLINDEX] must be the same as [BTSIP:BSCIP] or [BTSIP:BSCUPIP] for [BTSIP] corresponding to [ADJNODE:BTSID] or [ADJNODE:BTSNAME], or [IPPOOLIP] must be the same as [BTSEXTOPIP:BSCUPIP] for [BTSEXTOPIP] corresponding to [ADJNODE:BTSID] or [ADJNODE:BTSNAME].If [ADJNODE:NODET] specifies the adjacent node for the Abis, Iub, or SE interface, and [IPPOOL:MODE] for [IPPOOL] corresponding to [ADJNODE:IPPOOLINDEX] is set to ETHL2, only one [IPPOOLIP] can be added to the corresponding [IPPOOL].If [ADJNODE:NODET] specifies an adjacent node for the Se interface, the corresponding [ADJNODE:IPPOOLINDEX] must be different from [ADJNODE:IPPOOLINDEX] for adjacent nodes specified by [ADJNODE:NODET] for the Se interface.If [ADJNODE:NODET] specifies an adjacent node for the Iub interface and [ADJNODE:LogicRncId], [ADJNODE:NODEBID], and [ADJNODE:IPPOOLINDEX] are set to same values for adjacent nodes, and if [ADJNODE:CNMNGMODE] is set to EXCLUSIVE, [ADJNODE:CNOPINDEX] must be set to the same value for the adjacent nodes.-Parameter relationship with conditions:This parameter is valid if one of the following conditions is met:1.[ADJNODE:TRANST] is set to IP, ATM_IP.2.[ADJNODE:NODET] is set to A, ABIS.This parameter must be set if one of the following conditions is met:1.[ADJNODE:TRANST] is set to IP, ATM_IP.2.[ADJNODE:NODET] is set to A, ABIS.The parameter will be set with NULL when it is invalid.Read OnlyN/AN/AN/AN/AN/ANoneBSC6910 V100R015C00TransportADJNODEISROUTEMODEIs Route ModeBSC6910ADD ADJNODEMOD ADJNODEWhether to indicate it is the route mode when the node type is root node.NONOWRFD-02130501WRFD-05030104Dedicated Iub Transmission ControlDynamic AAL2 Connections in Iub/IuCS/Iur InterfaceEnumeration TypeNO(Not Route Mode), YES(Route Mode)NO~0, YES~1NoneNO, YESYES(Route Mode)NoneTransport Planning (Internal planning)Adjacent node-Parameter relationship with conditions:This parameter is valid only when [ADJNODE:IsROOTNODE] is set to YES.The parameter will be set with NULL when it is invalid.Read & WriteNo (And no impact on the UE in idle mode)N/AN/AN/A.N/ANoneBSC6910 V100R015C00TransportADJNODEIsROOTNODEIs Root NodeBSC6910ADD ADJNODEMOD ADJNODEWhether to indicate it is the root node when the transport type is ATM or ATM_IP.NOYESWRFD-02130501WRFD-05030104Dedicated Iub Transmission ControlDynamic AAL2 Connections in Iub/IuCS/Iur InterfaceEnumeration TypeNO(Not Root Node), YES(Root Node)NO~0, YES~1NoneNO, YESNoneNoneTransport Planning (Internal planning)Adjacent node-Configuration constraints:If [ADJNODE:IsROOTNODE] is set to NO, [ADJNODE:TRANST] for the adjacent node corresponding to [ADJNODE:UPPERANI] cannot be set to IP.If [ADJNODE:IsROOTNODE] is set to NO, [ADJNODE:NODET] must match [ADJNODE:NODET] for the adjacent node corresponding to [ADJNODE:UPPERANI].If [ADJNODE:IsROOTNODE] is set to NO, [ADJNODE:IsROOTNODE] for the adjacent node corresponding to [ADJNODE:UPPERANI] must be set to YES.If [ADJNODE:NODET] is set to IUR, [ADJNODE:TRANST] is set to ATM, [ADJNODE:IsROOTNODE] is set to NO, and [ADJNODE:RTMODE] is set to BYAAL2RT, [ADJNODE:UPPERANI] is not required. If these parameters are not set to the specified values, [ADJNODE:UPPERANI] must be configured. For adjacent nodes of other interfaces, if [ADJNODE:TRANST] is set to ATM and [ADJNODE:IsROOTNODE] is set to NO, [ADJNODE:UPPERANI] must be set to a value specified by [ADJNODE].-Parameter relationship with conditions:This parameter is valid only when [ADJNODE:TRANST] is set to ATM_IP, ATM.This parameter must be set when [ADJNODE:TRANST] is set to ATM_IP, ATM.The parameter will be set with NULL when it is invalid.Read & WriteNo (And no impact on the UE in idle mode)N/AN/AN/A.N/ANoneBSC6910 V100R015C00TransportADJNODELearnDipAutoDIP Automatic Acquisition SwitchBSC6910ADD ADJNODEMOD ADJNODEThis parameter is used to set whether to learn DIP automatically for adjacent node.NONOWRFD-150212WRFD-150243WRFD-150211RNC in Pool Node RedundancyIub IP Transmission Based on Dynamic Load BalanceRNC in Pool Load SharingEnumeration TypeNO(No), YES(Yes)NO~0, YES~1NoneNO, YESYES(Yes)YES(Yes)Transport Planning (Internal planning)None-Parameter relationship with conditions:This parameter is valid if one of the following conditions is met:1.[ADJNODE:TRANST] is set to IP, ATM_IP.2.[ADJNODE:NODET] is set to A, ABIS.The parameter will be set with NULL when it is invalid.Read & WriteNo (And no impact on the UE in idle mode)N/AN/ANoneN/ANoneBSC6910 V100R015C00TransportADJNODELogicRncIdLogical RNC IDBSC6910ADD ADJNODEUniquely identifies a logical BSC6910. A logic BSC6910 ID consists of 12-digit binary codes, and its value ranges from 0 to 4095. The BSC6910 is a logical node in the radio network subsystem (RNS) and controls the usage and allocation of radio resources.If "Load Sharing Type" is set to "OVERFLOW" or "Redundancy Type" is set to "BACKUP" in the "LST URNCBASIC" command during data configuration, this parameter must be input manually.If "Load Sharing Type" and "Redundancy Type" are set to "MASTER" in the "LST URNCBASIC" command during data configuration, the system automatically uses the value of the "BSC6910 ID" without input manually.NONOWRFD-010101WRFD-1502403GPP R9 SpecificationsRNC in Pool Multiple Logical RNCsInterval Type0~4095N/ANone0~4095NoneNoneRadio Planning (Internal planning)BSC6910-Configuration constraints:If [ADJNODE:NODET] specifies an adjacent node for the Iub interface, and if [ADJNODE:LogicRncId] and [ADJNODE:NODEBID] are set to same values for adjacent notes, [ADJNODE:CNMNGMODE] must be set to the same value for the adjacent nodes.If [ADJNODE:NODET] specifies an adjacent node for the Iub interface and [ADJNODE:LogicRncId], [ADJNODE:NODEBID], and [ADJNODE:IPPOOLINDEX] are set to same values for adjacent nodes, and if [ADJNODE:CNMNGMODE] is set to EXCLUSIVE, [ADJNODE:CNOPINDEX] must be set to the same value for the adjacent nodes.If [ADJNODE:NODET] specifies an adjacent node for the Iu-CS or Iu-PS interface, and if LogicRnc ShareMode is set to EXCLUSIVE but [ADJNODE:CNMNGMODE] is set to SHARE, only one adjacent node can be configured for each valid [ADJNODE:LogicRncId].If [ADJNODE:NODET] specifies an adjacent node for the Iu-CS or Iu-PS interface, and if both LogicRnc ShareMode and [ADJNODE:CNMNGMODE] are set to EXCLUSIVE, only one adjacent node can be configured for each operator corresponding to each valid [ADJNODE:LogicRncId] for this interface type.If [ADJNODE:NODET] specifies an adjacent node for the Iu-CS or Iu-PS interface, and if LogicRnc ShareMode is set to EXCLUSIVE, [ADJNODE:CNMNGMODE] for adjacent nodes with the same [ADJNODE:NODET] and [ADJNODE:LogicRncId] must be set to the same value.-Parameter relationship with conditions:This parameter is valid if one of the following conditions is met:1.[ADJNODE:NODET] is set to IUB.2.[ADJNODE:LogicRncShareMode] is set to EXCLUSIVE.This parameter must be set when [ADJNODE:LogicRncShareMode] is set to EXCLUSIVE.The parameter will be set with NULL when it is invalid.Read OnlyN/AN/AN/AN/AN/ANoneBSC6910 V100R015C00TransportADJNODELogicRncShareModeLogicRncShareModeBSC6910ADD ADJNODEThis Parameter indicates whether the adjacent node is shared by several logical BSC6910s or exclusive to one logical BSC6910.NONOWRFD-150211RNC in Pool Load SharingEnumeration TypeSHARE(SHARE), EXCLUSIVE(EXCLUSIVE)SHARE~0, EXCLUSIVE~1NoneSHARE, EXCLUSIVESHARE(SHARE)NoneTransport Planning (Internal planning)None-Parameter relationship with conditions:This parameter is valid only when [ADJNODE:TRANST] is set to IP.The parameter will be set with NULL when it is invalid.-Others:"NODET"=IUCS & "TRANST"=IP;or"NODET"=IUPS & "TRANST"=IP;When this parameter is chosen as EXCLUSIVE, the parameter Logical RNC ID will be displayed, otherwise the parameter Logical RNC ID will not be displayed.Read OnlyN/AN/AN/AN/A.N/ANoneBSC6910 V100R015C01TransportADJNODENAMEAdjacent Node NameBSC6910ADD ADJNODEMOD ADJNODEName of the adjacent node.NOYESGBFD-150201GBFD-118601GBFD-118605GBFD-118611WRFD-150244WRFD-05030104WRFD-150243A over IP Based on Dynamic Load BalancingAbis over IPIP QOSAbis IP over E1/T1Iu/Iur IP Transmission Based on Dynamic Load BalanceDynamic AAL2 Connections in Iub/IuCS/Iur InterfaceIub IP Transmission Based on Dynamic Load BalanceString Type1~64 charactersN/ANone1~64 charactersNoneNoneTransport Planning (Internal planning)Adjacent nodeNoneRead & WriteNo (And no impact on the UE in idle mode)N/AN/ANoneThe parameter modification has no impact on the equipment.NoneBSC6910 V100R015C00TransportADJNODENODEBIDNodeB IDBSC6910ADD ADJNODEID of the adjacent node to be added. The parameter is valid when Adjacent node type is set to IUB.NOYESWRFD-02130501WRFD-05030104Dedicated Iub Transmission ControlDynamic AAL2 Connections in Iub/IuCS/Iur InterfaceInterval Type0~65535N/ANone0~65535NoneNoneTransport Planning (Internal planning)Adjacent node-Configuration constraints:If [ADJNODE:NODET] specifies an adjacent node for the Iub interface, and if [ADJNODE:LogicRncId] and [ADJNODE:NODEBID] are set to same values for adjacent notes, [ADJNODE:CNMNGMODE] must be set to the same value for the adjacent nodes.If [ADJNODE:NODET] specifies an adjacent node for the Iub interface and [ADJNODE:LogicRncId], [ADJNODE:NODEBID], and [ADJNODE:IPPOOLINDEX] are set to same values for adjacent nodes, and if [ADJNODE:CNMNGMODE] is set to EXCLUSIVE, [ADJNODE:CNOPINDEX] must be set to the same value for the adjacent nodes.-Parameter relationship with conditions:This parameter is valid only when [ADJNODE:NODET] is set to IUB.This parameter must be set when [ADJNODE:NODET] is set to IUB.The parameter will be set with NULL when it is invalid.Read OnlyN/AN/AN/AN/AN/ANoneBSC6910 V100R015C00TransportADJNODENODETAdjacent Node TypeBSC6910ADD ADJNODEMOD ADJNODEType of the adjacent node.NOYESGBFD-150201WRFD-150212WRFD-150211GBFD-118601GBFD-118605GBFD-118611WRFD-150244WRFD-05030104WRFD-150243WRFD-020111A over IP Based on Dynamic Load BalancingRNC in Pool Node RedundancyRNC in Pool Load SharingAbis over IPIP QOSAbis IP over E1/T1Iu/Iur IP Transmission Based on Dynamic Load BalanceDynamic AAL2 Connections in Iub/IuCS/Iur InterfaceIub IP Transmission Based on Dynamic Load BalanceOne TunnelEnumeration TypeIUB(Iub Interface), IUR(Iur Interface), IUCS(Iu-CS Interface), IUPS(Iu-PS Interface), UNI_AAL2SWITCH(the adjacent node of the ATM switch on the Iub interface), NNI_AAL2SWITCH(the adjacent node of ATM switch on Iur or Iu-CS interface), ABIS(Abis Interface), A(A Interface), IURP(Iurp Interface), SE(SE Interface)IUB~0, IUR~1, IUCS~2, IUPS~3, UNI_AAL2SWITCH~4, NNI_AAL2SWITCH~5, ABIS~6, A~7, IURP~11, SE~14NoneIUB, IUR, IUCS, IUPS, UNI_AAL2SWITCH, NNI_AAL2SWITCH, ABIS, A, IURP, SENoneNoneTransport Planning (Internal planning)Adjacent node-Configuration constraints:If [ADJNODE:NODET] specifies an adjacent node for the Abis interface, only one [IPPOOLIP] can be added to [IPPOOL] corresponding to [ADJNODE:IPPOOLINDEX].If [ADJNODE:NODET] specifies an adjacent node for the Abis interface, and if [ADJNODE:BTSID] or [ADJNODE:BTSNAME] is set to the same value for adjacent nodes, [ADJNODE:CNMNGMODE] must be set to the same value for the adjacent nodes.If [ADJNODE:NODET] specifies an adjacent node for the Abis interface, and if [ADJNODE:BTSID] or [ADJNODE:BTSNAME] is set to the same value for adjacent nodes and [ADJNODE:CNMNGMODE] is set to EXCLUSIVE, [ADJNODE:CNOPINDEX] must be set to different values.If [ADJNODE:NODET] specifies an adjacent node for the Abis interface, and if [BTS:BTSTYPE] for the corresponding BTS is not set to EGBTS and [ADJNODE:CNMNGMODE] is set to SHARE, [IPPOOLIP] to be added to [IPPOOL] corresponding to [ADJNODE:IPPOOLINDEX] must be the same as [BTSIP:BSCIP]or [BTSIP:BSCUPIP] for [BTSIP] corresponding to [ADJNODE:BTSID] or [ADJNODE:BTSNAME]. - If [ADJNODE:NODET] specifies an adjacent node for the Abis interface, and if [BTS:BTSTYPE] for the corresponding BTS is not set to EGBTS and [ADJNODE:CNMNGMODE] is set to EXCLUSIVE, [IPPOOLIP] to be added to [IPPOOL] corresponding to [ADJNODE:IPPOOLINDEX] must be the same as [BTSIP:BSCIP] or [BTSIP:BSCUPIP] for [BTSIP] corresponding to [ADJNODE:BTSID] or [ADJNODE:BTSNAME], or [IPPOOLIP] must be the same as [BTSEXTOPIP:BSCUPIP] for [BTSEXTOPIP] corresponding to [ADJNODE:BTSID] or [ADJNODE:BTSNAME].If [ADJNODE:NODET] specifies an adjacent node for the Abis interface, [BTS] corresponding to [ADJNODE:BTSID] or [ADJNODE:BTSNAME] must exist.If [ADJNODE:NODET] specifies an adjacent node for the Abis interface, [BTS:SERVICEMODE] for [BTS] corresponding to [ADJNODE:BTSID] or [ADJNODE:BTSNAME] must be set to IP.If [ADJNODE:NODET] specifies an adjacent node for the Iu-CS, Iu-PS, or A interface, and if [ADJNODE:CNMNGMODE] is set to EXCLUSIVE, [ADJNODE:NODET] and [ADJNODE:CNOPINDEX] for [ADJNODE] cannot be set to the same value for the adjacent node at the same time.If [ADJNODE:NODET] specifies an adjacent node for the Iu-CS, or Iu-PS interface, and if [ADJNODE:CNMNGMODE] for the adjacent node in transmission pool networking mode is set to SHARE, adjacent nodes with the same [ADJNODE:NODET] cannot be configured in non-transmission pool networking mode.If [ADJNODE:NODET] specifies an adjacent node for the Iu-CS, Iu-PS, or A interface, and if [ADJNODE:CNMNGMODE] is set to SHARE, other adjacent nodes whose [ADJNODE:NODET] is the same as the adjacent node and [ADJNODE:CNMNGMODE] is set to SHARE cannot be configured.If [ADJNODE:NODET] specifies an adjacent node for the Iu-CS, Iu-PS, or A interface, and if [ADJNODE:CNMNGMODE] is set to SHARE, other adjacent nodes whose [ADJNODE:NODET] is the same as the adjacent node and [ADJNODE:CNMNGMODE] is set to EXCLUSIVE cannot be configured.If [ADJNODE:NODET] specifies an adjacent node for IURP, [EXTNODE] corresponding to [ADJNODE:ENID] must have been configured.If [ADJNODE:NODET] specifies an adjacent node for the Abis or A interface, and if [ADJNODE:CNMNGMODE] is set to EXCLUSIVE, the GSM operator corresponding to [ADJNODE:CNOPINDEX] must have been configured.If [ADJNODE:NODET] specifies the adjacent node for the Abis, Iub, or SE interface, and [IPPOOL:MODE] for [IPPOOL] corresponding to [ADJNODE:IPPOOLINDEX] is set to ETHL2, only one [IPPOOLIP] can be added to the corresponding [IPPOOL].If [IPPOOL:MODE] for [IPPOOL] is set to PPP_MP, only adjacent nodes specified by [ADJNODE:NODET] for the Abis interface can be added to the IPPOOL.If [ADJNODE:NODET] specifies an adjacent node for the Se interface, the corresponding [ADJNODE:IPPOOLINDEX] must be different from [ADJNODE:IPPOOLINDEX] for adjacent nodes specified by [ADJNODE:NODET] for the Se interface.If [ADJNODE:NODET] specifies an adjacent node for the Iub interface, and if [ADJNODE:LogicRncId] and [ADJNODE:NODEBID] are set to same values for adjacent notes, [ADJNODE:CNMNGMODE] must be set to the same value for the adjacent nodes.If [ADJNODE:NODET] specifies an adjacent node for the Iub interface and [ADJNODE:LogicRncId], [ADJNODE:NODEBID], and [ADJNODE:IPPOOLINDEX] are set to same values for adjacent nodes, and if [ADJNODE:CNMNGMODE] is set to EXCLUSIVE, [ADJNODE:CNOPINDEX] must be set to the same value for the adjacent nodes.If the SPX specified by [N7DPC:SPX] for [N7DPC] corresponding to [ADJNODE:DPX] is an assistor signaling point index, the SPX can reference the same DPX as other adjacent nodes but different [ADJNODE:NODET]. If the SPX specified by [N7DPC:SPX] for [N7DPC] corresponding to [ADJNODE:DPX] is not an assistor signaling point index, the DPX cannot be referenced by other adjacent nodes.If [ADJNODE:NODET] specifies an adjacent node for the Iu-CS or Iu-PS interface, and if both LogicRnc ShareMode and [ADJNODE:CNMNGMODE] are set to SHARE, only one adjacent node can be configured for interfaces of the same type.If [ADJNODE:NODET] specifies an adjacent node for the Iu-CS or Iu-PS interface, and if LogicRnc ShareMode is set to EXCLUSIVE but [ADJNODE:CNMNGMODE] is set to SHARE, only one adjacent node can be configured for each valid [ADJNODE:LogicRncId].If [ADJNODE:NODET] specifies an adjacent node for the Iu-CS or Iu-PS interface, and if LogicRnc ShareMode is set to SHARE but [ADJNODE:CNMNGMODE] is set to EXCLUSIVE, only one adjacent node can be configured for each operator index corresponding to this interface type.If [ADJNODE:NODET] specifies an adjacent node for the Iu-CS or Iu-PS interface, and if both LogicRnc ShareMode and [ADJNODE:CNMNGMODE] are set to EXCLUSIVE, only one adjacent node can be configured for each operator corresponding to each valid [ADJNODE:LogicRncId] for this interface type.If [ADJNODE:NODET] specifies an adjacent node for the Iu-CS or Iu-PS interface, and if LogicRnc ShareMode is set to EXCLUSIVE, [ADJNODE:CNMNGMODE] for adjacent nodes with the same [ADJNODE:NODET] and [ADJNODE:LogicRncId] must be set to the same value.If [ADJNODE:NODET] specifies an adjacent node for the Iur, Iu-CS, Iu-PS, or NNI_AAL2SWITCH, and if [ADJNODE:DPX] is set to a valid value, [N7DPC:DPCT] for [N7DPC] corresponding to [ADJNODE:DPX] must match [ADJNODE:NODET].The number of GPUs whose [BRD:LGCAPPTYPE] is set to UCUP multiplied by 700 must be greater than or equal to the number of adjacent nodes specified by [ADJNODE:NODET] for the Iub interface.If [ADJNODE:NODET] specifies an adjacent node for the IURP, [ADJNODE:ENID] must be set to different values.If [ALGCTRLPARA:RLFWACSW] is set to ON, only adjacent nodes specified by [ADJNODE:NODET] for the Abis interface can be added to [IPPOOL] corresponding to [IPPOOLIP:IPPOOLINDEX] for [IPPOOLIP] carried on physical ports specified by [ALGCTRLPARA:SRN], [ALGCTRLPARA:SN], and [ALGCTRLPARA:PN]. If [IPLOGICPORT:RLFWACSW] for the logical ports specified by [ADJLOGICPORTBIND:SRN], [ADJLOGICPORTBIND:SN], and [ADJLOGICPORTBIND:LPN] is set to ON, [ADJNODE:NODET] for [ADJNODE] corresponding to [ADJLOGICPORTBIND:ANI] must be the adjacent node for the Abis interface.If [ADJNODE:NODET] specifies an adjacent node for the Iub interface and [ADJNODE:SAALLNKN] is set to a valid value, the number of SAAL links over the UNI interface cannot exceed 500 in an SPU subsystem.If [ADJNODE:NODET] specifies an adjacent node for the Iub or Abis interface, and if [TRMLOADTH:THTYPE] for [TRMLOADTH] corresponding to [ADJNODE:TRMLOADTHINDEX] is set to BANDWIDTH, ensure that both of the following conditions are met: - [TRMLOADTH:FWDOVLDRSVBW] DTM comprehensive factors > quality factors > management factorsQUALITY(Quality): quality factors > capacity factors > DTM comprehensive factors > management factorsDTMMULTI(Allocation): DTM comprehensive factors > capacity factors > quality factors > management factorsMANAGEMENT1(Management 1): management factors > DTM comprehensive factors > capacity factors > quality factorsMANAGEMENT2(Management 2): management factors > capacity factors > quality factors > DTM comprehensive factorsNONOGBFD-114151DTMEnumeration TypeCAPACITY(Capacity), QUALITY(Quality), DTMMULTI(Allocation), MANAGEMENT1(Management 1), MANAGEMENT2(Management 2)CAPACITY~0, QUALITY~1, DTMMULTI~2, MANAGEMENT1~3, MANAGEMENT2~4NoneCAPACITY, QUALITY, DTMMULTI, MANAGEMENT1, MANAGEMENT2CAPACITY(Capacity)CAPACITY(Capacity)Default/Recommended ValueCell-Parameter relationship with conditions:This parameter is valid only when [GCELLGPRS:DTMOptiSwitch] is set to ON.The parameter will be set with NULL when it is invalid.Read & WriteNo (And no impact on the UE in idle mode)N/AN/ANoneThe parameter modification has no impact on the equipment.If this parameter is set to QUALITY(Quality), the speech quality is significantly improved but the multi-timeslot capability is not the optimal.If this parameter is set to CAPACITY(Capacity), the speech capacity is significantly improved but the multi-timeslot capability is not the optimal.If this parameter is set to DTMMULTI(Allocation), the multi-timeslot capability is significantly improved but the speech quality is not the optimal.If this parameter is set to MANAGEMENT1(Management 1), the management requirement is preferred. The speech quality, capacity, and multi-timeslot capability are not the optimal. The multi-timeslot capability, however, is better that that when this parameter is set to MANAGEMENT2(Management 2).If this parameter is set to MANAGEMENT2(Management 2), the management requirement is preferred. The speech quality, capacity, and multi-timeslot capability are not the optimal. The speech quality and capacity, however, are better than those when this parameter is set to MANAGE