Brochure by Module-1103 CoPSMs can be deployed on the same MSAP2000 shelf, to support ... OIM provides a STM-1 (155.52 Mbps) interface. ... SDH STM-1 complies with ITU-T G.707

A Compact and Cost-effectiveNGN Access Platform

Multiservice Access PlatformSM AP2000

www.zyflex.com.tw ZyFLEX

Multiservice Access Platform

Triple Play Services:- Analog Voice Interfaces- Digital Leased Line Interfaces- xDSL Interfaces- Ethernet Interfaces

Total Solution for Telephone Voice Services:- FXO: Dual Wire PSTN switch analog interface- V5.2AN: for PSTN V5.2 switch connection- Soft switch interface: H.248 & MGCP VoIP Gateway

Next Generation DSL Functions:- AAM Module includes 12 ADSL2+ Ports IPDSLAM

functions- Compliance with ITU-T G.992.1, G.992.2, ANSI

T1.413 issue 2, ADSL2 (G.992.3, G.992.4), ADSL2+(G.992.5) and ITU-T G.994.1

Ethernet over SDH:- Integration of SDH STM1 ADM functions- ITU-T G.7041/ ITU-T X.86 compliant EoS Support

Cross Connection & Grooming:- TSI technology incorporation- Input/Output port cross-connection at 64 kbps- E1 signal formation, via cross-connection at 64K/bits

time slot basisPacket Switch:

- IP Network switching functions, such as IEEE802.1d STP, 802.1p, Port-based & tag-based VLAN, GVRP, Broadcast storm control, and Static MAC address filtering.

Hybrid Optical:- Supports SDH STM1/4 optical trunk interface- Supports Gigabit Ethernet optical trunk interface

Redundancy Protection:- Common Modules include redundancy functions- Optical Interface Module includes 1+1 & SNC Protection

Network Management System (NMS):- Graphical User Interfaces (GUI)+ rich OAM&P functions- Remote System Management & Alarm generation- Lowers operation costs

Metallic Line Testing Module:- Confirms Loop status & performance- Online troubleshooting, to lower remote testing costs

Built-in Digital Test Functions:- Compliant with ITU-T O.150/O.151- Bit error rate testing for each digital channel- Lowers cost by being built-in & ready-to-use

Overview

Features

ZyFLEX

SM AP2000

ZyFLEX MSAP2000 is a next generation network (NGN) multiservice access gateway that provides voice, data, high speed Internet access, and Video services within a cost-effective platform. MSAP2000 not only offers traditional TDM voice services by its PSTN interfaces such as POTS and V5.2, but also supports voice over IP (VoIP) to connect with Softswitch in NGN. All MSAP2000 modules are designed as plug-in cards. System capacity can be easily expanded and upgraded, by addition of expansion shelves and plug-in cards, without the slightest interruption to services. MSAP2000’s flexible architecture and comprehensive interfaces allow carriers to deliver services to subscribers at their own pace. You pay as you grow.

MSAP2000’s compact and modular architecture, economically supports comprehensive services, including POTS, payphone, E&M, ISDN, PABX, leased-lines, and broadband data access. System capacity can be expanded and upgraded simply by adding new plug-in cards or expansion shelves, without interruption to ongoing services. Service Providers decide what they want, and only pay as they grow.

MSAP2000 is a universal platform for broadband loop carriers. It has integrated NG SDH ADM, Digital Cross Connect (DCS), Signaling Converter, narrow band DLC, along with broadband IP DSLAM, to deliver TDM and IP services on a simple compact platform.

Comprehensive Interfaces

Universal Platform

Flexible Network Topology MSAP2000 is designed to support flexible network topologies, such as ring, star, linear, tree & branch or point-to-point configurations. Versatile transmission media, such as fiber, copper wire, or wireless, can be used.

ZyFLEX SM AP2000

General Description

Feature List Brief Specification

Feature List

General Description

Brief Specification

Copyright © ZyFLEX Tech. Incorporation. All rights reserved. All specifications are subject to change without notice.

CoPSM Central Office Power Supply ModulePower Supply Module for MSAP2000’s Central Office Terminal

◇ Front Panel LEDs indicate power, fail and fuse status

◇ Reverse input polarity protection◇ Output over-voltage protection◇ Low output voltage alarm◇ Output over-current protection◇ Thermal overload protection◇ Redundant power protection

RtPSM provides DC to DC and DC to AC conversions. The DC/DC conversion fulfills System power requirements, while DC/AC provides Ring Generator for FXS and FXS-P on the MSAP2000 remote terminal. Both conversions are of isolated design, and both input and output ports are protected against over-voltage and over-current conditions, to ensure a stable power supply for MSAP2000 .The Ring Generator module is embedded within RtPSM, to generate ring voltage for FXS and FXS-P modules.Two RtPSMs can be deployed on the same MSAP2000 shelf, to support 1+1 redundant power supply function.RtPSM status and functions can be monitored by a CIT (Craft Interface Terminal) Menu-Driven interface, when linked to the MSAP2000 MPM control module via a RS-232 connection, or alternatively via a Graphical User Interface through Ethernet connection. The System administrator can directly oversee operations such as system power provisioning, alarm, status monitoring or maintenance

RtPSM Remote Terminal Power Supply ModulePower Supply Module for MSAP2000’s Remote Terminal

CoPSM is a DC power supply module that provides the power needed for MSAP2000’s central office terminal. CoPSM uses isolated DC power conversion, and both input and output ports are protected against over-voltage and over-current conditions, so that a stable power supply is ensured for the MSAP2000 Platform. Two CoPSMs can be deployed on the same MSAP2000 shelf, to support 1+1 redundant power.CoPSM status and functions can be monitored by a CIT (Craft InterfaceTerminal) Menu-Driven interface, when linked to the MSAP2000 MPM control module via a RS-232 connection, or alternatively via a Graphical User Interface through Ethernet connection. The System administrator can directly oversee operations such as system power provisioning, alarm, status monitoring or maintenance

◇ Front Panel LEDs indicate power, fail and fuse status◇ Reverse input polarity protection◇ Output over-voltage protection◇ Low output voltage alarm◇ Output over-current protection◇ Thermal overload protection◇ Redundant power protection◇ Embedded Ring Generator Module

DC-DC Converter

Output Current +5V@20Amp; -48V@3AmpTotal power: 250W (any loading combination)

Regulation +5.15V<1.5%load<0.2% per specified Temperature range

Input: -42 to -56 VDCIsolated output: +5.15V±1.5%; -48.0V±10% Low voltage disconnect: -42.0V±1V DC Low voltage alarm:-44.0 V DC

Isolation Internal converter: 500V input to outputOutput ground: Referenced to input battery ground

DC-DC Converter

DC/AC Converter

Output Current +5V@20Amp; -48V@3Amp; -24V@3AmpTotal power: 250W (any loading combination)

Regulation +5.15V<1.5%load<0.2% per specified Temperature range

Input: -42 to -56 VDCIsolated output: +5.15V±1.5%; -24.0V±10%;-48.0V±10% Low voltage disconnect/alarm : -42.0V±1V DC /-44.0 V DC Ringer: 60Vrms~85Vrms; 17Hz~50Hz.

Isolation Internal converter: 500V input to outputOutput ground: Referenced to input battery ground

ZyFLEX SM AP2000

General Description


Feature List

General Description

Brief Specification


MPM Main Processing ModuleControls and Manages MSAP2000 System Functions

◇ Panel LEDs indicate system status, fault, alarm and network activation status

◇ RS-232 interface for Craft Interface Terminal◇ RJ-45 interface for NMS connection◇ Module management and Time-Slot assignment◇ Configurable to assign different administration privileges ◇ Self diagnostics and fault report◇ Configurable alarm generation and report◇ Non-volatile provisioning for data storage◇ Timing source selection and synchronization◇ Order wire interface◇ System temperature detection

OIM Optical Interface ModuleProvides Next Generation SDH Transmission Technology for MSAP2000

On the MSAP2000 platform, OIM (Optical Interface Module) provides next generation SDH transmission technology. OIM supports various topologies, such as Point-to-point, Star, Ring, Tree and Branch, to connect the MSAP2000 COT and RT, and to help carriers build up an optical broadband access network. OIM provides a STM-1 (155.52 Mbps) interface. In order to maintain transportation stability, OIM supports 1+1 protection switching, as well as a SCNP protection mechanism, which complies with ITU-T.G.841 standards. An error rate of less than 50ms is guaranteed during optical protection switch, to prevent disconnection of ongoing calls. In addition to auto protection switching, OIM also supports the manual set-up switch mode. A protection switch threshold can be set up, based on performance monitoring, to indicate major alarms during protection switching.

.

◇SDH STM-1 complies with ITU-T G.707◇ Supports STM-1 SNCP Protection◇ 1+1 Protection◇ Supports Various Network Topologies such as Ring,

Star, Tree and Branch ◇ Provides 2430X2430 Digital Cross Connect◇ Supports Performance Monitoring ◇ Alarm/Error detection and report

MPM provides two types of management interfaces: a SNMP Agent with Ethernet link, and a Local Craft Interface with RS-232. With either Ethernet or RS-232, the operator can easily manage the MSAP2000 COT and RT. MPM offers full OAM&P functions such as system provisioning, channel assignment/bandwidth control, performance monitoring, and maintenance.MPM also provides 1+1 redundancy. When an active MPM malfunctions, the system management mechanism will switch to redundancy mode. MPM also supports the Warm Boot function. When MPM software needs to be upgraded, the latest versions can be downloaded via the internet or intranet. During the MPM Warm boot process, voice services may continue without interruption.MPM has a built-in flash memory, for storage of System configuration settings. All settings may revert to default values when necessary.

Clock Sources

Accuracy:± 4.7ppm @ 25°C Stability:± 2 ppm External Clock:2.048 MHz (G.703)Primary/Secondary Input: 2.048Mbps (Framed all “1”)Tributary Clock: Selectable from any service slot

Ethernet Port Two 10/100BaseT Ethernet ports Comply with IEEE 802.3

Local Console RS-2329.6 ~ 115.2 KbpsAlarm Contacts 5 alarm outputs, 7 alarm inputs

PortsLine Rate

One link per Module155.52 Mbit/s ± 20 ppm

TransmitterParameter

Complies with ITU-T G.957Source Type:FP/DFBMax. Mean Launch Power:0dBm(L-1.1, L-1.2) Min. Mean Launch Power:-5dBm(L-1.1, L-1.2)

Optical Line Code

Receiver Parameter

Binary non-return-to-zero after scramblingBER ≤ 10-10 Minimum sensitivity:-34 dBm(L-1.1, L-1.2) Minimum Overload: -10 dBm(L-1.1, L-1.2)

ZyFLEX SM AP2000

General Description


Feature List

General Description

Brief Specification


ELM Extension Link ModuleExtends the Capacity of the MSAP20000 Main Shelf

EPM Extension Processing ModuleExpands MSAP2000 Network Capacity

ELM (Extension Link Module) is set up on the MSAP2000 main shelf, and it connects to the EPM in the extension shelf, for system expansion. ELM adopts the multi-mode fiber optical transport technology, which provides a full bandwidth of 155.52Mbps. ELM has a special Digital Cross Connect function, which freely exchanges 2430 DS0 digital ways.ELM can be installed in any slot from 1 to18, on the MSAP2000 main shelf. The SC fiber optical connector on the panel allows for convenient handling. 8 ELMS can be installed within one MSAP2000, to provide connection to up to 8 extension shelves.LED lights on the ELM panel indicate the operation status, to help maintenance personnel pinpoint problems swiftly and easily.

EPM (Extension Processing Module) is set up on the MSAP2000 extension shelf, and it connects to the ELM in the main shelf, to provide system capacity expansion of a MSAP2000 node. EPM has adopts the multi-mode fiber optical transport technology, which offers a full bandwidth of 155.52 Mbps. EPM has a special Digital Cross Connect function, which freely exchanges 2430 DS0 digital ways.EPM can only be installed in slots 19 and 20. The SC fiber optical connector on the panel allows for convenient handling. One MSAP2000 will support up to 8 extension shelves.LED lights on the EPM panel indicate the operation status, which will help maintenance personnel to pinpoint problems swiftly and easily.

◇Front Panel LED indicates active, fail, fuse status◇ 1+1 Protection◇ Provides 2430X2430 Digital Cross Connect◇ Supports Performance Monitoring◇ Alarm/Error detection and report◇ Use of non-volatility memory components for efficient

data storage

◇Front Panel LED displays indicate active, fail, fusestatus

◇ 1+1 Protection◇ Provides 2430X2430 Digital Cross Connection◇ Supports Performance Monitoring ◇ Alarm/Error detection and report◇ Use of non-volatile memory components, to save data

efficiently

PortsLine Rate



Wave;ength: 1310nmSource Type: MLMOutput power: -14dBm ~ -20dBm

Optical Line CodingReceiver Parameter

Binary non-return-to-zero after scramblingWavelength: 1260~1360nmMinimum receiving power: - 32dBm at BER ≤ 10-10

PortsLine Rate


Optical Line Coding Binary non-return-to-zero after scrambling


Wave;ength: 1310nmSource Type: MLMOutput power: -14dBm ~ -20dBm

Receiver Parameter

Wavelength: 1260~1360nmMinimum receiving power: - 32dBm at BER ≤ 10-10

Frame Format Complies with ITU-T G.707

ZyFLEX SM AP2000

General Description


Feature List

General Description

Brief Specification


QE1M Quad E1 ModuleServes as a Leased Line Interface, Trunk Module, or V 5.2 Switch E1

◇ Quad E1 Links per Module◇ Configurable for Tributary Module,

Trunking, or V5.2 E1 Interface◇ Supports Line Traffic Performance Monitoring◇ Alarm/Error detection and reporting◇ Built-in Digital Cross-connect◇ Optional impedance at 120Ω/75Ω◇ Supports grooming for Nx64kpbs◇ Supports AMI or HDB3 Line Coding◇ Provides Nx64Kpbs (Fractional Grooming)

The 4-port Quad E1 Module can function as a Leased Line interface, Trunking Module, or a V5.2 E1 interface on the MSAP2000 Platform. It supports User Leased Line Services on the Subscriber (RT ) end, and it can connect to PBX, to support voice services. The Quad E1 Module supports data services when set at a bandwidth of Nx64Kpbs (N=1~31).Service Providers can set up E1 bandwidths and use QE1M groomingfunctions to maximize E1 bandwidth utilization. With QE1M, 16 E1 cards can be installed in one shelf, to provide a capacity of up to 63 E1. QE1M is compatible with most brands of modems or E1 multiplexers, to provide integrated DLC (IDLC) functions.

2W/4W E&M provides two-wire or four-wire services. It supports four subscriber line circuits configured for operation with E&M types I or V (a special version of E&M will support various types of E&M mode I, II, III, IV, and V). When installed in the MSAP2000 shelf, it provides four analog voice channels, which will interface with the telephone network over an E1 access facility.The E&M service card maps the four analog voice ports into four DS0 time slots, in an E1 access link. It also detects the signaling, converts it into 4-bit signals and passes these signals into timeslot 16 of the E1 link, using Channel Associated Signaling (CAS). The four voice channels can be connected to PBXs, key telephone systems, and security facilities.In addition, the E&M service card also provides an interface for analog leased line modems. To optimize transmission performance, the E&M service card also offers a Transmission Only (TO) capacity. No signaling is done when configured to TO mode.

2W/4W E&M 2W/4W Ear-and-Mouth ModuleProvides 2-wire and 4-wire Services for the MSAP2000 System

◇ Four 2W/4W E&M interfaces per card◇ E&M Type I, II, III, IV, V◇ Compliant with A-law or u-law coding◇ Transmit and Receive gain configurable per channel◇ Mix E&M and TO services on same Service Card◇ Impedance : 600 Ω◇ Metallic Line Testing support with MLTM◇ Transient protection◇ Channel status detection and Signaling transmission

PortsLine Rate

Four links per Module2048 Kbit/s ± 50 ppm

Line Coding ITU-T G.703 AMI or HDB3 (software configurable)

PerformanceMonitoring G.826

Timing Sources Up to two sources can be selectedFrame Format Complies with ITU-T G.704

ImpedanceCRC Process

120Ω, 75Ω available ITU-T G.706

PortsSignaling

Four channels per ModuleType Mode I, II, III,IV, V Normal/Tandem/TO Mode

Coding Rule ITU-T G.711 A-law or U-law (software configurable)

TransmissionPerformance

Attenuation/Frequency Distortion: complies with ITU-T G.702Group Delay Distortion w, Frequency: complies withITU-T G.712

Signaling Format CAS or CCS software configurableImpedance Balanced 600Ω

ZyFLEX SM AP2000

General Description


Feature List

General Description

Brief Specification


FXO (Foreign Exchange Office) is installed in the MSAP2000 shelf at the Central Office Terminal (COT), and provides a 2-Wire switch interface. FXO digitizes analog voice signals by A-law or μ-law, and uses the Time Division Multiplex (TDM) technology. It can then be linked to MSAP2000 at the Remote Terminal (RT) through different trunks, such as SDH or E1. The corresponding FXS connects service providers to their customers’telephones, fax machines and analog modems, to provide high-quality telecommunication services.Each FXO Line Card provides sixteen 2-wire switch interfaces, and every shelf will accommodate up to 16 FXO line cards, so that every shelf can provide a maximum of 256 interfaces. In addition, when addtional channels are required, the MSAP2000 system can provide 8 additional shelves through use of ELM and EPM modules. Up to 1890 voice lines can be supported.

FXO-P (Foreign Exchange Office) is installed in the MSAP2000 shelf at the Central Office Terminal (COT), and provides a 2-Wire switch interface. FXO-P digitizes analog voice signals by A-law or μ-law, and uses the Time Division Multiplex (TDM) technology. Each FXO-P Line Card provides 8 2-wire switch interfaces, and every shelf will accommodate up to 16 FXO-P line cards, so that every shelf can provide a maximum of up to 128 interfaces. In addition, MSAP2000 can expand system capacity by use of ELM and EPM modules.FXO-P can detect billing signals such as battery reversal or metering pulse (12/16 KHz ;3Vrms~5Vrms billing pulse voltage). When billing signals are detected, FXO-P will convert them into digital signaling, and the signaling will be transported to RT and be regenerated into corresponding billing signals, to drive the payphone’s billing system.

FXO-P Foreign Exchange Payphone ModuleA High-Density Payphone Interface, to support PSTN Switching

FXO Foreign Exchange Office ModuleA High-Density Analog Interface, to support PSTN Switching

◇ 16-channel VF interfaces to PSTN Switch per card◇ Support A-law or u-law coding◇ Provides ring detection◇ Transmission rate ≥ 31.2 Kbit/s on ITU-T V.34 modem

application◇ Supports Caller ID service◇ Impedance : 900 Ω◇ Metallic Line Testing support with MLTM◇ Channel status detection and signaling transmission

◇ 8-channel Pay phone interfaces to PSTN Switch per card ◇ Compliant with A-law or u-law coding◇ Battery Reversal Detection◇ 12/16 KHz metering pulse Detection◇ Impedance : 900 Ω◇ Metallic Line Testing support with MLTM◇ Front Panel LEDs indicate Operation Status◇ Channel status detection and Signaling transmission◇ Alarm/Error detection and report

Ports 16 voice channels per line cardCoding Rule ITU-T G.711 A-law or U-law (software configurable)

SignalingSpecification

Dial Tone Detection:supports DP and DTMFSignaling Format:CAS or CCS (software confugurable)Tip-Ring Reversal: Polarity ReversalRing Detection:16Hz~50Hz V.34 Modem Support:33.6Kbps with BER ≤ 10-7

Impedance 900Ω (other impedances are software configurable)

Ports 8 voice channels per line cardCoding Rule ITU-T G.711 A-law or U-law (software configurable)


Dial Tone Detection:supports DP and DTMFSignaling Format:CAS or CCS (software confugurable)Tip-Ring Reversal: Polarity ReversalRing Detection:16Hz~50Hz Metering Pulse: 3Vrms~5Vrms 16 KHz ±160 Hz

12 KHz Optional by S/w setting

Impedance 900Ω (other impedances are software configurable)

Self Diagnostic Memory Diagnostic; Metallic Line Testing

ZyFLEX SM AP2000

General Description


Feature List

General Description

Brief Specification


FXS-P (Foreign Exchange Station – Pay phone) provides an interface for payphone connection. FXS-P is installed at the MSAP2000 Remote Terminal (RT); it digitizes analog voice signals by A-law or μ-law, and employs the Time Division Multiplex (TDM) technology, to connect to the MSAP2000 COT via different trunk methods, such as SDH, Giga Ethernet or E1. The MSAP2000 COT provides several analog and digital E1 interfaces, such as FXO or V5.2, which enables the MSAP2000 system to interconnect different switches, and provide high-quality voice service to customers. Each FXS-P Line Card supports 8 interfaces, and every shelf can support up to 16 FXS line cards, to provide up to 128 interfaces. FXS-P can receive and switch billing signals from the polar operation, and 12 or 16 KHz (3Vrms~5Vrms billing pulse voltage). When FXO-P detects billing signals, it converts the signals and delivers them to the RT, where they become corresponding billing signals, to drive the payphone billing system.

FXS-P Foreign Exchange Station Payphone ModuleHigh-Density Analog Payphone Services

◇ 8-Channels interfaces to Pay phone per card◇ Compliant with A-law or u-law coding◇ Provides Battery Reversal◇ 12/16 KHz metering pulse Generation◇ Impedance : 600 Ω◇ Metallic Line Testing support with MLTM◇ Transient protection◇ Front Panel LEDs indicate Operation Status◇ Channel status detection and Signaling transmission◇ Alarm/Error detection and report◇ Hot Line function

FXS (Foreign Exchange Station) Module provides traditional Public Switch Telephone Network (PSTN) services. FXS is generally installed at the Remote Terminal (RT), and can be connected to subscribers' CPEs, such as telephones, fax machines and analog modems. FXS digitizes analog voice signals by A-law or μ-law, then creates a connection to different switches by FXO, V5.2 (PSTN), or PVM (software switch) to provide guaranteed voice services. Every FXS Line Card provides 16 POTS ports, and 16 FXS line cards can be installed in each shelf, to support up to 256 ports. FXS functions include Ring voltage, Hook detection, DC current feeding, and it also supports Caller ID services. FXS also has a built-in circuit security device, which complies with IEC 61000-4-5 Class 2 and FCC Part 68 standards, to shield FXS from electrical shock or damages. FXS supports automatic testing of telephone lines, with MLTM (Metallic Line Test Module).

◇ 16-Channels Voice interfaces per card◇ Provides a Loop Start Interface◇ Transmission rate ≥ 31.2 Kbit/s on ITU-T V.34 Modem

application◇ Supports Caller ID services◇ Impedance : 600 Ω◇ Metallic Line Testing support with MLTM◇ Transient protection◇ Front Panel LEDs indicate Operation Status◇ Channel status detection and Signaling transmission◇ Compliant with A-law or u-law coding◇ Alarm/Error detection and report

FXS Foreign Exchange Station ModuleHigh-Density Analog Voice & Modem Services

Ports 16 voice channels per line cardCoding Rule ITU-T G.711 A-law or mu-law (software configurable)


Dial Tone Detection:supports DP and DTMFSignaling Format:CAS or CCS software confugurableTip-Ring Reversal: Polarity ReversalRing:External ring provided by RtPSMLoop Resistance: 1200ΩMinimal initial current: ≧20mA (loop current configurable)V.34 Modem Support: 33.6Kbps with BER ≤ 10-7

Impedance 600Ω (other impedances are optional)

Ports 8 voice channels per line cardCoding Rule ITU-T G.711 A-law or u-law (software configurable)


Dial Tone Detection:supports DP and DTMFSignaling Format:CAS or CCS software confugurableTip-Ring Reversal: Polarity ReversalMetering Pulse: 1V~3V 16 KHz ±160 Hz

12 KHz Optional by S/W setting Loop Resistance: 1200ΩLoop Voltage: - 48±6V nominal (on hook)

Impedance 600Ω (other impedances are optional)

ZyFLEX SM AP2000

General Description


Feature List

General Description

Brief Specification


LUNT provides four ISDN “U” interfaces on the MSAP2000 platform. LUNT is installed at the COT end, to provide an ISDN basic rate interface (BRI) for the ISDN switch. LUNT’s counterpart is LULT, which is located at the RT end. The LUNT BRI module will fit in any of the slots from 1 ~ 16 on the MSAP2000 shelf. LUNT provides an interface for the ISDN switch with 2B1Q ( 2 binary 1 quaternary) line coding, for full-duplex transmission. The LUNT interface can extract timing information from the switch, and send it to MPM for clock synchronization.All traffic originated from each LUNT can be multiplexed into a SDH STM-1/4 optical link. With fiber to the building (FTTB) and fiber to the curb (FTTC) infrastructures, MSAP2000 is able to extend its ISDN BRI service area to as far as up to 50 km.

LULT provides four ISDN “U” interfaces on the MSAP2000 platform. LULT is installed at the RT end, to provide an ISDN basic rate interface (BRI) for ISDN NT1. LULT will fit in any of the service slots, from 1 ~ 16, and it serves as an interface for the ISDN NT1 with 2B1Q (2 binary 1 quaternary) line coding, for full-duplex transmission. LULT provides remote power feeding for NT1, ranging from 90V ~110 V. LULT transfers 2B+D-channel signals as a number of 64 kbps signals. At the Central Office terminal, LUNT will regenerate the 2B+D signal for relay to the ISDN switch.As with LUNT, the EOC channel allows the User to conduct remote OAM&P functions such as fault, performance, configuration, and alarm management. This reduces operational costs, while simultaneously delivering excellent transmission quality to customers.

◇ 4 ISDN circuits per module◇ Supports 3-DS0 TDM◇ Compliant with ETSI ETR 080◇ Compliant with ANSI T1.601◇ Provides Performance monitoring ◇ EOC channel enables remote management◇ Supports 2B+D, B1 only, and B2 only loopback ◇ Provides tributary timing for system clock source◇ Reduce the cost of operating and maintenance with a

high performance SNMP management

◇ 4 ISDN circuits per module◇ Supports 3-DS0 TDM◇ Compliant with ETSI ETR 080◇ Compliant with ANSI T1.601 ◇ Provides Performance monitoring◇ EOC channel enables remote management◇ Supports 2B+D, B1 only, and B2 only loopback◇ Provides tributary timing for system clock source◇ Reduce the operation and maintenance costs

with high performance SNMP management

LUNT U-Interface Network Terminal ModuleISDN BRI Network Module

LULT U-Interface Line Terminal ModuleISDN BRI Local Module

PortsFrame Structure

4 links per moduleETSI ETR 080

Activation Sequence& EOC

ETSI ETR 080

ESSESUASLOSWE

PerformanceMonitoring


4 links per moduleETSI ETR 080

Activation Sequence& EOC

ETSI ETR 080

Payload Rate:144 Kbps (2B+D) Line Rate:80 kbaud (160 Kbps) Line Coding:2BIQInput Impedance:135 Ω ± 5% Sealing Current Termination:400 Ω

Physical Characteristics

ZyFLEX SM AP2000

General Description


Feature List

General Description

Brief Specification


Each ADSL line card can support 12 user ports. The ADSL Line Card is compliant with ITU-T standards G.992.3, and G.992.5. It can also deliver broadband services at a transmission rate of up to 24 Mbps. In order to rapidly deploy mass-market voice and broadband services, Service Providers need simple and scalable carrier-class management systems that can lower equipment and network management costs. MSAP2000’s ADSL line card is centrally managed by the Main Processing Module (MPM), which also serves as a SNMP agent. This is deployed together with the SNMP manager provided by the OptiVista Network Management System. With its friendly Graphical User Interface (GUI), the OptiVista NMS provides a comprehensive set of OAM&P functions, which include provisioning, fault, performance, and alarm management. This allows for an extremely efficient and cost effective solution for network resource planning and management.

AAM ADSL Access ModulexDSL Interfaces + Gigabit Switch Core for Swift Broadband Access

◇ Twelve ADSL 2/2+ ports per module◇ Compliant with ITU-T G.992.1, G.992.2, G.992.3, ◇ G.992.5 – ADSL, G.Lite◇ Connects to the Internet through IP network◇ Enables the IP traffic tunnel to run through an existing

SDH network◇ Realizes the “Ethernet all the way” network

infrastructure ◇ Uses high performance SNMP management to reduce

operation and maintenance costs

Metallic Line Testing ModuleProvides Channel Loop Test Functions for the MSAP2000 System

MLTM

◇ Supports Hot Swap functions◇ Conducts External Loop testing (includes voltage,

resistance and capacity), DTMF/Dial Pulse testing,Dial channel testing, Howler voice, Ring subscriber, V-Port (includes Monitoring), and wrong numbertesting.

◇ Metallic Line Testing ◇ Allows Operators to conduct Last Miles testing, via

connection to LCT or NMS.

The Metallic Line Testing Module (MLTM) provides channel and loop test functions, such as loop resistance, dial tone, ring tone, howler voice, line number, wrong number, and DTMF, which will enable Operators to swiftly pinpoint errors, and confirm loop status and quality. MLTM’s built-in digital testing functions provide test patterns which comply with ITU-T O.150 and O.151, and can be applied towards random digital channels for error testing. MLTM’s V-port interface will connect the Operator to the COT Helpdesk,for elimination of more complex faults and errors. The Operator can send test commands via the user interface or NMS, and the loop test results will be displayed on the UI or NMS. With MLTM, Operators can establish connections via public networks or Leased lines, and conduct remote testing or cross-district testing of distant areas.

Ports

Line Standard Support

12 x ADSL Ports per line card

ITU-T G.992.1, G.992.2ANSI T1.413 issue 2ADSL2 (G.992.3, G.992.4)ADSL2+ (G.992.5)

Backplane Connection

100 Mbps EthernetSupport 802.3/3UMax. Frame size: 1522 bytes

Test Items

Input Power

Dial Channel: Stage 2Dial Tone: Stage 1 & 3DTMF: Stage 3V-Port:Stage1 & 3Line Number: Stage 3Wrong Line: Stage 1 & 3Howler Voice: Stage 3Copper Test: Stage 1 & 3-48VDC/0.05A5VDC/1.2A

Power 10W@25。C Testing

ZyFLEX SM AP2000

General Description


Feature List

General Description

Brief Specification


The newest Ethernet over SDH Module (EoSM) has been integrated into the MSAP2000. EoSM is termed ‘CEoSM’ in the central office, and ‘REoSM’ at the remote end. CEoSM is connected directly to the networking router through the RJ45 port on its front panel, and it has one PHY/MAC to substitute for the 8 port switch. This card provides an Ethernet uplink for MASP2000 by its SDH/Ethernet inter-working. CEoSM is an Ethernet device which receives and transmits Ethernet traffic between CEoSM and the router; its bandwidth ranges from 64Kbps~100Mbps, according to individual user settings.On the MSAP2000 shelf, CEoSM and REoSM are respectively installed at the central and remote terminal, to transmit the AAMs (ADSL Access Module) Ethernet packet through the STM-1 trunk. Within other applications, CEoSM can function as a one- port Ethernet module, to transport peer to peer Ethernet traffic.

REoSM RT Ethernet over SDH Switch ModuleAn Advanced Ethernet Switch over SDH Module, at the Remote Terminal

An Advanced Ethernet Switch over SDH Module, at the Central Terminal

COT Ethernet over SDH Switch ModuleCEoSM

◇ Enables the IP traffic tunnel to channel through the SDH network

◇ Realizes the “Ethernet all the way” network infrastructure

◇ Front Panel LED displays active, fail, and alarm status◇ Complies with IEEE 802.3, 802.3u, and 802.3x

Ethernet Standards◇ Automatic MDI/MDIX crossover for each 10Base-T/

100Base-TX port◇ Auto-sensing 10/100Mbps Ethernet RJ-45 port.

◇ Enables the IP traffic tunnel to channel through the SDH network

◇ Realizes the “Ethernet all the way” network infrastructure

◇ Front Panel LED displays indication for active, fail, and Port status

◇ Complies with IEEE 802.3, 802.3u, and 802.3x Ethernet Standards

◇ Automatic MDI/MDIX crossover for each 10Base-T/ 100Base-TX port

◇ 8x auto-sensing 10/100Mbps Ethernet RJ-45 ports

MSAP2000’s REoSM is an 8-port 10/100 Mbps Ethernet switch, and it fits into slot 18 of the MSAP2000 shelf. REoSM provides auto-sensing 10/100 Mbps switching capabilities for efficient connectivity to servers, workstations and other attached devices. Its Plug-and-Play usability, outstanding price-to-performance ratio, and flexible design, makes REoSM a simple andaffordable solution for a wide range of applications.REoSM’s IEEE 802.3x standard-based flow control allows EoSM to prevent traffic congestion, by informing attached devices to halt transmissions. When the switches detect that the buffer of each port is nearly full, the attached devices are requested to wait until new data can be accepted. Flow control allows 100 Mbps full duplex connections between servers and switches, with minimum data transfer loss.

PortsProtocol

1 Uplink Ethernet PortCSMA/CD

Transfer Rate 14880 packets/s for 10 Mbps148800 packets/s for 100 Mbps

VLAN Port-based VLANIEEE 802.1Q Tag VLAN

Ethernet over SDH 64 Kbps ~ 100 Mbps (Configurable)ITU-T G.7041 GFP or X.86 optional

IP Multicasting Supports IGMP Snooping, and 2 types of Query mode

PortsProtocol

8 Ethernet Ports per line cardCSMA/CD

Transfer Rate 14880 packets/s for 10 Mbps148800 packets/s for 100 Mbps

VLAN Port-based VLANIEEE 802.1Q Tag VLAN

Ethernet over SDH 64 Kbps ~ 100 Mbps (Configurable)ITU-T G.7041 GFP or X.86

Class of Service IEEE 802.1PSupports 2 transmission priorityQoS

ZyFLEX SM AP2000

General Description


Feature List

General Description

Brief Specification


PVM Packet Voice ModuleVoIP Connection & Interconnection to Softswitch

V5 Processing ModuleSupports V5.1, V5.2 Interfaces to the Local Exchange

V5P

◇ Complies with ETSI, ITU-T G.964 and G.965◇ Supports Multiple V5.2 interfaces◇ Provides up to 16 E1 links on each V5.2 ◇ Processor Redundancy support◇ Layer 2:LAPV5 and ISDN D-channel Frame Relay◇ Layer 3 V5.2: Also provides BCC, Link Control, and

Protection protocols◇ ISDN PRA support, and Protection Switching◇ Fully tested for compliance with ETSI ATS, and

proven to operate with LE switches

V5 Processing Module (V5P) supports V5.1, V5.2 interfaces to the local exchange. It fully complies with the ETSI and ITU-T G.964, ITU-T G.965 protocol standards.V5P can support up to four V5.2 systems and each V5.2 system cansupport up to 16 E1 links. The total processing capacity of V5P is 1920 POTS lines. V5P can be installed in any service slot.The protocols implemented on V5P include LAPV5-EF, LAPV5-DL, Link Control, Bearer Channel Connection (BCC), PSTN, Control, and Protection protocols. V5P and QE1M form a V5.2 AN system set. In addition to meeting ITU-T.G. 964, 965 standards, QE1M also measures up to ITU-T G.703/G.704/G.706 interface standards. The operator can set up all kinds of V5P operation parameters, warning and operation controls, as well as monitor transmission performance with a local craft Interface, or a SNMP link.

PVM (Packet Voice Module) provides VoIP features, and allows for interconnection to various soft-switches. PVM supports different VoIP protocols such as SIP, MGCP or H.248 (MEGACO). PVM can be installed with various voice interfaces such as FX/FXO-P/FXS/FXS-P/E&M to support migration from existing PSTN to soft-switch. PVM can also be provisioned for use on MSAP2000/MSAP8000 system backplanes, and the packet can be aggregated to comply with MSAP2000/MSAP8000 GbE gigabit trunk interface s. In order to provide scalability and maintain transmission stability, multiple PVMs can be installed on the same shelf. This type of configuration provides load sharing, load balancing and n+1 protection.PVM supports various voice coders such as G.711, G.729A/B and G.723.1. This allows users to utilize bandwidth fully, without compromising voice connectivity for subscribers. Voice coder performance plus a QoS network interface guarantees top-rate voice services.

◇ Multiple VoIP protocol support (SIP, Megaco, and MGCP)

◇ Up-to 256 G.711 voice-coder channels, simultaneously.

◇ Redundant design◇ QoS support ◇ Provides 64kbps level Digital Cross Connect◇ Supports Performance Monitoring ◇ Alarm/Error detection and report

V5.1/V.52

Protocols

Complies with ITU-T G.964/965Supports up to four V5.2 system

PSTN, BBC, Control, Link, Protection Protocols

System Functionalities

Full Layer Management CapabilityProcessor Redundancy supportProvides up to 1:4 PSTN POTS Concentration C-Channel signaling on TS-16, -15, and -31 on each trunk

Ethernet PortLine Interface

1 Link per ModuleIEEE802.3, 10/100BaseT

Encapsulation Voice/RTP/UDP/IPv4 *IPv6 planned

QoSProtocol

802.1P/QSIP (RFC 3261), MGCP(RFC 3624), H.248/Megaco

Gain Control

Packet Intervals

RX/TXG.711: 5ms, 10ms ~ 60msG.726: 10ms~ 60msG.729a/b: 10ms~60msG.723.1: 30ms and 60ms.

ZyFLEX SM AP2000

General Description


Feature List

General Description

Brief Specification


GbE Gigabit Ethernet ModuleA 16TX +2Gb Intelligent Switch

Ethernet Switch ModuleAn Ethernet Switch for connection to Servers, Workstations & Other DevicesESM

MSAP2000’s ESM is an 8-port 10/100 Mbps Ethernet switch which provides auto-sensing 10/100 Mbps switching capabilities, for efficient connectivity to servers, workstations and others attached devices. Plug-and-Play usability, outstanding price-to-performance ratio, and flexible designs, make ESM a simple and affordable solution for a wide range of applications.The IEEE 802.3x standard-based flow control allows ESM to prevent traffic congestion by informing the attached devices to halt transmissions. When the switches detect that the buffer of each port is nearly full, the attached devices are requested to wait until new data can be accepted. Flow control allows 100 Mbps full duplex connections between servers and switches, with minimum data transfer loss.

◇ Front Panel LEDs indicate active, fail, fuse status◇ Complies with IEEE 802.3, 802.3u, and 802.3x

Ethernet standards◇ Automatic MDI/MDIX crossover for each 10Base-T/

100Base-TX port◇ 8x auto-sensing 10/100Mbps Ethernet RJ-45 ports◇ Half-duplex mode for backpressure, and Full-duplex

for flow control ◇ Automatic address learning and address migration ◇ 8K-entry MAC address table◇ 2Mbit memory buffer sharing◇ LED-indicators: system (Power), 10/100 TX (100M,

LK/ACT, FDX/COL)◇ Reduces operation and maintenance costs, with

high performance SNMP management

GbE is a 16TX+2Gb Intelligent Switch. This switch is a store-and-forward device that offers low latency for wire speed networking. This grants service providers an alternative for utilizing SFP module + CAT5 cable, for last mile access network deployment.GbE provides comprehensive Layer 2 switch functions, such as Port Trunking, VLAN Tagging, QoS Policy, IGMP snooping, and bandwidth control. Increments can be as small as 62Kbits/sec, or as large as 256Mbits/sec.IEEE 802.3x standard-based flow control helps GbE to prevent packet loss. When the switches detect that the buffer of each port is nearly full, the attached GbE is requested to wait until new data can be accepted. Flow control allows 10/100/1000 Mbps full duplex connections with minimum data transfer loss.GbE also protects investments by its capability for remote software upgrade, and scheduled reboots will minimize interruption of ongoing services.

◇ 2 Gigabit SFP + 16 10/100 ports◇ Complies with IEEE802.3, IEEE 802.3u, IEEE802.3z,

IEEE 802.1q and IEEE 802.3x◇ Store-and-forward switching architecture for abnormal

packet filtering◇ 8K-entry MAC address table◇ LED-indicators for active, fail and link status◇ SNMP Network Management

Ports 8 Ethernet ports per line card Protocol CSMA/CD

Ethernet over SDH 64 Kbps ~ 100 Mbps (Configurable)ITU-T G.7041 GFP or X.86 optional

Technology

Transfer Rate

Store-and-Forward Switching14880 packets/s for 10 Mbps148800 packets/s for 100 Mbps

Standards

IEEE 802.3, IEEE 802.3u IEEE 802.3x Flow controlIEEE 802.1D Spanning TreeIEEE 802.1Q VLAN TaggingIEEE 802.1p Class of ServiceIEEE 802.3 ad Link aggregation

Connector2 ports SFP J-45 connectors on front panelFor management/debugging

Technology Store-and-Forward Switching

Standards

IEEE 802.3u 100 Base TXIEEE 802.3z Gigabit LXIEEE 802.3x Flow controlIEEE 802.3ad Port TrunkIEEE 802.1p Class of ServiceIEEE 802.1Q VLAN Tagging

ZyFLEX SM AP2000

General Description


Feature List

General Description

Brief Specification


GSH-R G.SHDSL ModemFull Duplex Symmetric Transmission

G.SHDSL ModuleFull Duplex Symmetric Transmission

G.SHDSL

MSAP2000 supports a G.SHDSL solution for leased line services. The SHDSL solution consists of a G.SHDSL line card at the MSAP2000 Remote Terminal (RT), and a G.SHDSL modem at customer premises. This solution provides full duplex symmetric transmission by the Trellis Coded Pulse Amplitude Modulation (TCPAM) line code, and it is fully compliant with ITU-T G.991.2 and G.994.1 standards.Each GSH line card within the MSAP2000 shelf can provide one G.SHDSL user port. MSAP2000 GSH not only replaces E1 leased lines, but also offers flexible multi-rates from 192 kbps to 2312 kbps by 64 kbps increments. Moreover, the G.SHDSL modem located at the customer end will provide flexible interfaces such as V.35, EIA530, LAN, and E1. The control message carried in the EOC channel will be transmitted by a single pair of copper wires for provision of comprehensive OAM&P functions, including fault, performance, configuration, and alarm management.

◇ Fully compliant with ITU-T G.994.1 & ITU-T G.991.2 Annex A and B

◇ Employs TCPAM Technology to offer symmetric/asymmetric high speed data transmission over single-pair copper wires

◇ EOC channel enables remote management◇ Adaptive multi-rate from 192 kbps to 2312 kbps (N*64

Kbps)◇ Provides fault, performance, configuration, and

security management ◇ Provides self-testing & loopback testing for trouble

shooting support

MSAP2000 supports a G.SHDSL solution for leased line services. The SHDSL solution consists of a G.SHDSL line card (GSH) installed in MSAP2000 at the Remote Terminal (RT), and a G.SHDSL modem (GSH-R) at customer premises. Each GSH line card provides one G.SHDSL link to the GSH-R modem, and it provides full duplex transmission for leased line services over twisted copper pairs. GSH-R is fully compliant with ITU-T G.991.2 and G.994.1 standards, and provides full duplex symmetric transmission by Trellis Coded Pulse Amplitude Modulation (TCPAM) line code.GSH-R provides flexible standard digital interfaces such as V.35, EIA530, LAN, and E1. GSH-R not only replaces E1 leased lines, but also offers flexible multi rates from 192 kbps to 2312 kbps in 64 kbps increments. Moreover, it also provides a 10/100 Ethernet interface for LAN connection.GSH-R can be remotely managed through a centralized SNMP-based NMS with a Web-based GUI, or a local control console equipped at MSAP2000’s front panel.

◇ Fully compliant with ITU-T G.994.1 & ITU-T G.991.2 Annex A and B

◇ Employs TCPAM Technology to offer symmetric/asymmetric high speed data transmission over single-pair copper wires

◇ EOC channel enables remote management◇ Adaptive multi-rate from 192 kbps to 2312 kbps (N*64

Kbps)◇ Flexible E1/T1/V.35/Ethernet DTE interface◇ Provides self-testing & loopback testing for trouble

shooting support


1 Link per ModuleITU-T G.991.2

Payload Rate NX 64kbit/s (2≦N≦36)

Activation SequenceThreshold Alarm

Complies with ITU-T G.991.2 &ITU-T G.994.1 Handshaking15-minute of ES, SES, UA S24-hour of ES,SES, UAS


ES, SES, UAS, LOSWE, Current 15-minute parameters32 previous 15-minute parameters24-hour period of parameters7 previous-24 hour periods


1 Link per ModuleITU-T G.991.2

Payload Rate NX 64kbit/s (2≦N≦36)

Activation SequenceThreshold Alarm

Complies with ITU-T G.991.2ITU-T G.994.1 Handshaking15-minute of ES, SES, UA S24-hour of ES,SES, UAS


ES, SES, UAS, LOSWE, Current 15-minute parameters32 previous 15-minute parameters24-hour period of parameters7 previous-24 hour periods

www.ZyFLEX.com.tw

www.ZyFLEX.com.tw4F, No.5-2, Industry E. 9th Rd.,Science Park, Hsinchu 30075

Taiwan, R.O.C.Tel: 886-3-5679168 ext.704

Fax:886-3-5679188Email: [email protected]

Documents

Brochure by Module-1103 CoPSMs can be deployed on the same MSAP2000 shelf, to support ... OIM provides a STM-1 (155.52 Mbps) interface. ... SDH STM-1 complies with ITU-T G.707