Upload
ledang
View
220
Download
2
Embed Size (px)
Citation preview
BRAZOS FOREST PRODUCTS
PRODUCT LISTINGS
December 2013
STOCK MOULDINGS
THE ABOVE PROFILES ARE AVAILABLE IN ALL OTHER SPECIES UNDER OUR “CUSTOM RUN” PROGRAM
CROWNS
8012 9/16 x 4-1/4” Red Oak Maple Poplar Alder
DENTIL 13/16 x 5-7/16” Red Oak Maple Poplar Alder
8013 9/16 x 3-5/8” Red Oak Maple Poplar Alder
DENTIL 3/4 x 3-11/16” Red Oak Maple Poplar Alder
8010 9/16 x 2-3/4” Red Oak Maple Poplar Alder
HUNTWICK 9/16 x 4-1/2” Red Oak Maple Poplar Alder
8014 9/16 x 3-1/4” Red Oak Maple Poplar Alder
COVE 11/16 x 3-3/4” Red Oak Maple Poplar Alder
TEXAS 3/4 x 4-3/8” Red Oak Maple
LARGE COVE 11/16 x 5-1/4” Alder Maple Poplar
MODIFIED COVE 5/8 x 4-1/4” Alder Poplar Red Oak
1
BASE & CASING MOULDINGS
C211 CASING 5/8 x 2-1/2” Red Oak
LC11 CASING 11/16 x 3-1/2” Red Oak
LB 11 BASE 5/8 x 4-1/2” Red Oak
ACOL. CASING 11/16 x 2-1/2” Red Oak
FLUTED 3/4 x 3-1/2” Red Oak
FLUTED 3/4 x 5-1/2” Red Oak
THE ABOVE PROFILES ARE AVAILABLE IN ALL OTHER SPECIES UNDER OUR “CUSTOM RUN” PROGRAM
STOCK MOULDINGS
CORNER MOULDS
VINTAGE 3/4 x 2-3/4”
Red Oak Maple Poplar Alder
BEADED 3/4 x 2-3/4”
Red Oak Maple Poplar Alder
CLASSIC 3/4 x 2–3/4”
Red Oak Maple Poplar Alder
ROUND BLOCK 1” x 3”
Red Oak Maple Poplar Alder
ROPE 3/4 x 2-3/4”
Red Oak Maple Poplar Alder
2
CM 12 3/4 x 2”
Red Oak Maple
LIP D 13/16 x 1-5/8” Red Oak Maple
SHAKER 3/4 x 2”
Red Oak Maple
FP DÉCOR 6 1”x 1-5/8” Red Oak
LIP MOULDS
DÉCOR 6 1” x 1-5/8”
Red Oak Maple Poplar
LIP A 13/16 x 1-3/8” Red Oak Maple
Z LIP 7/16 x 5/8”
Red Oak Maple Poplar Alder
INSERT MOULDS
DENTIL 3/8 x 5/8”
Red Oak Maple
Poplar Alder
ROPE 3/8 x 5/8”
Red Oak Maple
Poplar Alder
STOCK MOULDINGS
THE ABOVE PROFILES ARE AVAILABLE IN ALL OTHER SPECIES UNDER OUR “CUSTOM RUN” PROGRAM
3
PANEL MOULDS
CR7 1-1/8 x 2-1/2” Red Oak Maple
CM3 1/2 x 3/4” Red Oak Maple
Poplar Alder
PM5 11/16 x 1-1/8” Red Oak Maple Poplar
Alder Mahogany
CR2 3/4 x 1-1/2” Red Oak Maple
Poplar Alder
PM6 3/4 x 1-7/8” Red Oak Maple Poplar
Alder Mahogany
F 3/4 x 1-1/2” Red Oak Maple
Poplar Alder
M 1/2 x 1” Red Oak Maple
Poplar Alder
N 1/2 x 3/4” Red Oak Maple
STOCK MOULDINGS
MISCELLANEOUS MOULDINGS
OSC 3/4 x 3/4”
Red Oak Maple Poplar Alder Ash
ISC 3/4 x 3/4” Red Oak Maple
LT RAIL 13/16 x 1-5/8” Red Oak Maple
Poplar Alder
VALENCE 1-15/16 x 2-3/8” Red Oak Maple
Poplar Alder
SCRIBE 1/4 x 13/16”
Red Oak Maple Poplar Alder
L FLAT 1/4 x 1-1/2”
Red Oak Maple Poplar Alder
SCREEN 1/4 x 3/4” Red Oak Maple
SHOE 1/2 X 3/4”
Red Oak Maple
SHOE 5/8 X 13/16”
Red Oak Maple Poplar Alder
THE ABOVE PROFILES ARE AVAILABLE IN ALL OTHER SPECIES UNDER OUR “CUSTOM RUN” PROGRAM
ISC 1/2 x 1/2” Red Oak Maple
TONGUE & GROOVE
3/4” x 5-1/2” Alder Maple
R. Oak Poplar
4
S4S LUMBER
1x1-1/2 1x2 1x4 1x6 1x8 1x12
HARDWOODS
ALDER * * * *
KNOTTY ALDER * * * * AROMATIC CEDAR CHERRY HICKORY MAHOGANY * * * MAPLE * * * * * * POPLAR * * * * * * RED OAK * * * * * * WALNUT *
WHITE PINE
#2 *
#3 *
5
6
HARDWOOD PLYWOOD
RUSSIAN BIRCH 3M 5X5 6M 5X5 9M 5X5
12M 5X5 12M 4X8 15M 5X5 18M 5X5 18M 4X8
BIRCH IMPORT
2.6M A4 VC PS 5.2M A4 VC PS 5.2M B2 VC WPF 5.2M B4 MDF BEADED 5.2M C2 VC WPF 5.2M C2 VC WPF UV 1S 5.2M C2 VC WPF 4X10 5.2M D4 VC WPF 12M C2 VC WPF 12M C2 VC WPF UV 1S 12M C2 VC WPF UV 2S 12M D2 VC WPF 12M EE VC WPF 15M C2 VC WPF 18M B2 VC WPF 18M C2 VC WPF 18M C2 VC WPF BrazosCore 18M C2 VC WPF UV 1S 18M C2 VC WPF UV 2S 18M C2 VC WPF 4X10 18M D2 VC WPF 18M EE VC WPF 25M C2 VC WPF
ALDER IMPORT
5.2M A4 VC PS 5.2M C4 VC PS KNOTTY 18M A1 VC PS 18M CC VC PS KNOTTY
DOMESTIC
5/32 B4 VC PS 1/4 A4 VC PS 1/4 AC MDF PS BEADE 1/4 C4 MDF PS KNOTTY 1/2 B4 VC PS 1/2 B4 MDF PS 3/4 A2 VC PS 3/4 A2 MDF PS 3/4 CC VC PS KNOTTY 3/4 CC VC PS 4X10
ASH IMPORT
5.2M B4 VC WPF WHITE 18M B2 VC WPF WHITE
DOMESTIC
3/4 B2 VC WPF WHITE
BEECH IMPORT
5.2M A4 VC PS 5.2M A2 MDF WPF 5.2M A4 MDF WPF 5.2M A2 VC PS 12M B2 VC WPF 18M A2 VC WPF 18M A2 VC PS
7
HARDWOOD PLYWOOD
BIRCH DOMESTIC
1/4 B2 VC WPF 1/2 B2 VC WPF 3/4 B2 VC WPF 3/4 B2 VC WPF WHITE 3/4 B2 VC WPF 4X10 3/4 C2 VC WPF 3/4 D2 VC WPF 3/4 D3 VC WPF 4X10
CEDAR AROMATIC 5.2M VC RUSTIC
CHERRY IMPORT
5.2M A4 VC PS 5.2M A1 MDF PS 18M A1 VC PS
CHERRY DOMESTIC
1/4 A4 MDF PS 1/4 A2 MDF PS 3/4 A2 VC PS SM# 3/4 A2 MDF PS SM# 3/4 A2 MDF PS 4X10
FIR 3/8 ACX VC 1/2 ACX VC 3/4 ACX VC 3/4 AB VC MARINE
HICKORY IMPORT
5.2M A4 VC PS 5.2M A4 MDF PS 12M B2 VC WPF 1/2 B4 MDF WPF DOMESTIC 18M A2 VC PS
MAHOGANY IMPORT
5.2M A4 VC PS 18M A1 VC PS
MAHOGANY DOMESTIC
1/4 B2 MDF PS 1/4 A4 VC PS 4X10 3/4 A1 MDF PS SM# 3/4 A1 VC PS SM# 3/4 A1 MDF PS 4X10
MAPLE IMPORT
5.2M A4 VC PS 5.2M B4 VC WPF 5.2M B2 VC WPF 5.2M B2 MDF WPF 5.2M B2 VC WPF 5.2M C4 VC WPF 12M B2 VC WPF 18M B2 VC WPF 18M C2 VC WPF
8
RED OAK DOMESTIC
5.2M B2 MDF WPF 5.2M B2 MDF PS 1/4 A4 VC RIFT 1/4 A4 VC QTRD 1/4 B2 VC WPF 1/4 B2 MDF BEADED 1/4 B4 VC WPF 1/4 B4 MDF WPF 1/4 B4 VC BEADED 1/4 A4 VC WPF 4X10 1/2 B2 VC WPF 1/2 B4 VC WPF 3/4 A1 VC WPF 3/4 A1 VC RIFT 3/4 A1 VC QTRD 3/4 A1 VC PS 4X10 3/4 A1 MDF PS 3/4 A2 VC WPF 3/4 B2 VC WPF 3/4 C2 VC WPF
WHITE OAK IMPORT
5.2M A4 VC PS-RIFT-QTRD 18M A1 MDF PS 18M A1 VC PS-RIFT-QTRD
DOMESTIC
3/4 A1 MDF PS SM# 3/4 A1 MDF RIFT 3/4 A1 MDF QTRD
HARDWOOD PLYWOOD
MAPLE DOMESTIC
1/4 B4 MDF BEADED 1/2 B2 VC WPF 3/4 A1 VC WPF 3/4 A1 MDF PS SM# 3/4 A1 VC PS SM# 3/4 A1 MDF PS 4X10 3/4 B2 MDF WPF 3/4 B2 VC WPF 3/4 C2 VC WPF 3/4 D3 VC WPF 3/4 D3 VC WPF 3/4 D3 VC WPF 4X10 3/4 EE VC WPF
MERANTI
2.6 BBCC 5.2M BBCC EXT 5.2 BBCC 8X4 BENDING 9M BBCC 4X8 BENDING 9M BBCC 8X4 BENDING 18M PRIMO PLY
RED OAK IMPORT
2.6M A4 VC PS 5.2M A4 VC PS-RIFT-QTRD 5.2M A2 VC PS 5.2M B4 VC WPF 5.2M B2 MDF WPF 12M B2 VC 18M A1 VC PS-RIFT-QTRD 18M B2 VC WPF 18M C2 VC WPF
9
ROTARY CUT (WPF)
The log is mounted centrally in the lathe and turned against a razor
sharp blade, like unwinding a roll of paper. Since this cut follows the log's annular growth rings, a bold varie-gated grain marking is produced.
Rotary cut veneer is exception-ally wide.
FLAT CUT OR PLAIN SLICED The half log, or flitch, is mounted with the heart side flat against the
flitch table of the slicer and the slic-ing is done parallel to a line through the center of the log. This produces a
variegated figure.
RIFT CUT The veneer is produced in the vari-ous species of Oak. Oak has me-dullary ray cells which radiate from the center of the log like the curved spokes of a wheel. The rift or comb grain effect is obtained by cutting at
an angle of about 15% off of the quartered position to avoid the flake
figure of the medullary rays.
QUARTER SLICED The quarter log or flitch is mounted on the flitch table so that the growth
rings of the log strike the knife at approximately right angles, produc-
ing a series of stripes, straight in some woods, varied in others.
HARDWOOD VENEER CUTS
HARDWOOD PLYWOOD
WHITE PINE
MPORT
5.2M A4 VC PS KNOTTY 18M A2 VC PS KNOTTY
WALNUT DOMESTIC
3/4 A2 MDF PS SM# 3/4 A2 VC PS SM#
IMPORT
5.2M A4 VC PS 18M A2 VC PS
10
MELAMINE WHITE
1/4 MDF 1S 1/2 IPB 2S 1/2 MDF 2S 1/2 IPB 2S 4X10 5/8 IPB 2S 3/4 IPB 1S 3/4 IPB 2S 3/4 IPB 2S NAUF 3/4 MDF 2S 3/4 MDF 2S NAUF 3/4 VC 2S HPL CAB LNR 3/4 VC 1S HPL CAB LNR 1” IPB 2S
ALMOND
1/4 MDF 1S 3/4 IPB 2S
BLACK
1/4 MDF 1S 5/8 IPB 2S 3/4 IPB 2S 3/4 MDF 2S
FOG & FOLKSTONE GREY
1/4 MDF 1S 3/4 IPB 2S
MAPLE
1/4 MDF 1S 1/2 IPB 2S 4X10 3/4 IPB 2S
EXTIRA MDF 1/2 4X8 3/4 4X8
IND. BOARD PRODUCTS
MDF INDUSTRIAL
5.2 4X8 1/4 4X8 STD & NAUF 3/8 4X8 1/2 4X8 STD & NAUF 1/2 4X10 5/8 4X8 11/16 4X8 STD & NAUF 3/4 4X8 STD & NAUF 3/4 4X10 3/4 5X8 3/4 5X10 3/4 5X12 1” 4X8 1-1/8 4X8 1-1/8 5X8
PLUM CREEK
3M 4X8 5.2M 4X8 1/4 4X8 1/2 4X8 5/8 4X8 3/4 4X8 3/4 4X10 3/4 5X12 18M 4X8 1” 4X8
IPB
3/8 4X8 1/2 4X8 STD & NAUF 5/8 4X8 11/16 4x8 STD & NAUF 3/4 4X8 STD & NAUF 1” 4x8 STD & NAUF 1-1/8 4X8 1-1/8 4x10 1-1/8 5X8 1-1/8 5x10 1-1/8 5x12
11
VENEER AND ARCHITECTURAL PANELS
Veneers
91 Species of Exotic Woods
Pressure Sensitive Adhesives (PSA)
Paper Backed Veneer 10 Mil; 20 Mil; 30 Mil
Wood Edgebanding
NBL– No Black Line
Duraback and Phenolic
2 Ply; 3 Ply Wood on Wood Laminates
Architectural Panels
Available In:
Running book Matched
Balanced Book Matched
Center-Balance Matched
Running Slip-Matched
Random Matched
Flitch Matched
Sequenced and Numbered End Matched
Reverse Slip Match (Swing Match)
Core Options
MDF
Plywood
Veneer Core
Particle Board
Fire Rated Particle Board & MDF
Cut to Size Available
Std Sizes– 4’ or 5’ Wide by 8’, 10’ or 12’ Long.
Edge Banding Available*
12
HARDWOOD LUMBER
ALDER 4/4 - 5/4 - 6/4 - 8/4 - 10/4
SUPERIOR - PREMIUM FRAME
STANDARD FRAME
ASH 4/4 - 5/4 - 6/4 - 8/4
FAS
BASSWOOD 4/4 SELECT & BETTER
BEECH 4/4 - 8/4
SUPERIOR - SUPCOLOR
BIRCH 4/4 SELECT & BETTER
CHERRY 4/4 - 5/4 - 6/4 - 8/4
SELECT & BETTER
HICKORY 4/4 - 5/4
FAS
HARD MAPLE 4/4 - 5/4 - 6/4 - 8/4
SELECT & BETTER
SOFT MAPLE 4/4 - 5/4 - 6/4 - 8/4 - 10/4
SELECT & BETTER
MESQUITE 4/4 3’-5’
CLEAR AND RUSTIC
POPLAR 4/4 - 5/4 - 6/4 - 8/4 - 10/4 - 12/4 - 16/4
#1 COMMON - FAS
RED OAK 4/4 - 5/4 - 6/4 - 8/4 - 10/4
#1 COMMON & FAS RIFT AND QTRD
WHITE OAK 4/4 - 5/4 - 6/4 - 8/4
FAS - RIFT AND QTRD
WALNUT 4/4 - 5/4 - 6/4 - 8/4
FAS - #1 COMMON
SOFTWOOD LUMBER
AFRICAN MAHOGANY
4/4 - 5/4 - 6/4 - 8/4 - 10/4 - 12/4
FAS
GENUINE MAHOGANY
4/4 - 8/4
FAS
SIPO 4/4 - 6/4 - 8/4
FAS
MERANTI 4/4 - 5/4 - 6/4 - 8/4
FAS
OKOUME 4/4 - 6/4 - 8/4 - 10/4
FAS
AROMATIC CEDAR 4/4 #1 COMMON
WHITE PINE PONDEROSA - RADIATTA
3/4 S4S 4/4 - 8/4 RGH #3 - #2 - C GRADE
IMPORTED HARDWOOD
LUMBER
EXOTIC HARDWOOD
LUMBER
The RED is in stock the BLUE is special order from our Carolina Yard
AFROMOSIA ANDIROBA – ANIGRE - AVODIRE
BLACK & WHITE LIMBA - BANAK - BUBINGA CANARYWOOD - CARIBBEAN CHERRY
CHECHEN (Caribbean Rosewood) CUMARU - IPE (Brazilian Walnut)
JATOBA (Brazilian Cherry) - LYPTUS LACEWOOD - MAKORE (African Cherry)
MAKASSAR EBONY - MORADO (Bolivian Rosewood) ODORATA CEDAR - PADOUK - PURPLEHEART
SANTOS MAHOGAN - TEAK TIGERWOOD (Goncalo Alves)
SPANISH CEDAR – SAPELE - SHEDUA WENGE – YELLOWHEART - ZEBRAWOOD
FAS 4/4 –8/4
CALL FOR AVAILABILITY
13
14
FAS FAS derives from an earlier grade known as "First and Seconds". It is the best and most expensive grade. Boards 6" and wider, 8' and longer. Yields 83-1/3 percent of clear face cuttings with minimum sizes of 4" x 5', or 3" x 7'. Suitable for fine furniture, interior joinery, solid wood moldings, and other applications where clear, wide boards are needed.
FAS 1-Face (F1F) One face meets FAS requirements and the poorer face meets Number 1 Common grade requirements. Usually combined with FAS lumber, thereby providing at least one FAS face.
Selects Face side is FAS, back side is No. 1 Common. Boards are 4" and wider , 6' and longer. Yields 83-1/3 percent clear face cuttings with minimum sizes of 4" x 5', or 3" x 7'. A cost effective substitute for FAS when only one good face is required.
No. 1 Common Often referred to as "Cabinet" grade in the USA due to its extensive use for kitchen cabinets. Boards are 3" and wider, 4' and longer. Yields 66-2/3 percent clear face cuttings with minimum sizes of 4" x 2', or 3" x 3'. Provides good value, especially if rela-tively small pieces can be used.
No. 2A Common Also known as "Economy" grade. Boards are 3" and wider, 4' and longer. Yields 50 percent clear face cuttings 3" and wider by 2' and longer. Grade of choice for US hardwood flooring industry.
No. 2B Common Same as No. 2A Common, except that stain and other sound defects are admitted in the clear cuttings. An excellent paint grade.
Sound Wormy Same requirements as #1 Common and better but wormholes, limited sound knots and other imperfections allowed. Not commonly available.
No. 3A Common Boards are 3" and wider, 4' and longer. Yields 33-1/3 percent clear face cuttings 3" and wider by 2' and longer. Economical choice for rough utility applications:, crates, palettes, fencing, etc.
No. 3B Common Boards are 3" and wider, 4' and longer. Yields 25 percent clear face cuttings 1-1/2" and wider by 2' and longer. Applications same as No. 3A Common.
Source: National Hardwood Lumber Association
IT’S ALL
Our Chinese made BIRCH and “BrazosCore” plywood are manufactured the way cabinet makers want their panels, with solid kiln dried #1 plies in the core. These cores are superior in quality to all other cores that are available in the market today. The plies are hand selected for their soundness and minimum core voids. Additional care is
given to the drying to avoid delaminating and warping.
*BrazosCore is a calibrated panel (sanded to exact thickness) with #1 kiln dried cores and meranti faces. Available in 18m only.
THE
ABOUT
CORE!
FACTS ABOUT OUR IMPORTED
P L Y W O O D
CORBELS
A-1 Small Acanthus Corbel 4-5/8 x 5-1/4 x 10
A-2 Medium Acanthus Corbel 5" x 7" x 14"
A-3 Large Acanthus Corbel 6-3/4" x 7-3/4" x 22"
T-3 Large Traditional Corbel 6 3/4" x 7 5/8" x 22"
T-2 Medium Traditional Corbel 5" x 7" x 14"
T-1 Small Traditional Corbel 4-1/2" x 5-1/4" x 10"
G-1 Small Grape Corbel 4-1/2" x 5-1/4" x 10"
G-2 Medium Grape Corbel 5" x 7" x 14"
G-3 Large Grape Corbel 6-3/4" x 7-3/4" x 22"
T-4 Traditional Bar Bracket 3-3/8" x 7-3/4" x 13"
A-4 Acanthus Bar Bracket 3-1/2" x 7-3/4" x 13"
G-5 Narrow Grape Corbel 3" x 9" x 12"
MAPLE—ALDER—RUBBERWOOD
AVAILABLE IN RED OAK AND CHERRY—SPECIAL ORDER
15
CORBELS
A-13 Medium Acanthus Corbel 5-3/8" x 3-3/4" x 12-1/2"
A-12 Small Acanthus Corbel 3-1/2" x 3" x 8"
A-5 Low Profile Acanthus 2-3/4" x 1-3/8" x 6"
A-6 Low Profile Acanthus 3-1/2" x 1-1/2" x 8"
A-7 Low Profile Acanthus 4-1/2" x 1-3/4" x 10"
A-8 Mini Acanthus Corbel 3" x 1-3/4" x 4-1/4"
A-9 Low Profile Acanthus 2-3/4" x 1-1/2" x 4-1/2"
A-10 Low Profile Acanthus 3-1/2" x 1-1/4" x 5-1/2"
A-11 Low Profile Acanthus 4-1/2" x 2" x 7"
T-5 Mini Traditional Corbel 2-7/8" x 1-3/4" x 4-1/4"
PB-9 Plinth Block 3-3/4" x 7" x 1"
R-8 Rosette 3-3/4" x 3-3/4" x 1"
MAPLE—ALDER—RUBBERWOOD
AVAILABLE IN RED OAK AND CHERRY—SPECIAL ORDER
16
PEDESTAL FOOT
PED-2-C Pedestal Foot Cor-ner
PED-2-L Pedestal Foot Left 8-1/4" x 4" PED-2-M Pedestal Foot Middle
16" x 3"
PED-2-R Pedestal Foot Right 8-1/4" x 4"
PED-3-CR Rounded Pedestal Foot Corner 7" x 7" x 4"
PED-3-L Pedestal Foot Left 6" x 4"
PED-3-M Pedestal Foot Middle 11-1/2" x 2"
PED-3-R Pedestal Foot Right 6" x 4"
MAPLE—ALDER—RUBBERWOOD
AVAILABLE IN RED OAK AND CHERRY—SPECIAL ORDER
17
ONLAYS
ONLAY-1-S 20" x 4" x 3/4"
Hand Carved Onlay
ONLAY-1-M 24" x 5" x 3/4"
Hand Carved Onlay
ONLAY-1-L 36" x 7-1/2" x 7/8"
Hand Carved Onlay
ONLAY-2-S 20" x 4-1/4" x 3/4"
Hand Carved Onlay
ONLAY-2-M ONLAY-2-M 24" x 5" x 3/4"
Hand Carved Onlay
ONLAY-2-L 36" x 7-1/2" x 7/8"
Hand Carved Onlay
ONLAY-3-S 20" x 5" x 5/8"
Hand Carved Onlay
MAPLE—ALDER—RUBBERWOOD
AVAILABLE IN RED OAK AND CHERRY—SPECIAL ORDER
18
BUN FEET AND LEGS
BUNN-2
Turned Bunn Foot 4" x 4"
BUNN-3
Turned Bunn Foot 4" x 6"
LEG-8 Carved Leg
4" x 4" x 9"
LEG-5 Carved Ball and Claw Leg
4" x 4" x 8"
LEG-3 Ball & Claw Leg
4-1/8" x 4-1/8" x 6"
LEG-4 Ball & Claw Leg
4" x 4" x 8"
MAPLE—ALDER—RUBBERWOOD
AVAILABLE IN RED OAK AND CHERRY—SPECIAL ORDER
19
BUN FEET AND LEGS
LEG-6 Traditional Queen Anne Leg
4" x 4" x 6" LEG-7 Traditional Queen Anne Leg
4" x 4" x 8"
LEG-1 Carved Leg
3-1/2" x 3-1/2" x 5"
LEG-2 Acanthus Leg
3-1/2" x 3-1/2" x 5"
BUNN-1 Bunn Foot
5" x 3"
BUNN-4 Crown Bunn Foot
5" x 3"
MAPLE—ALDER—RUBBERWOOD
AVAILABLE IN RED OAK AND CHERRY—SPECIAL ORDER
20
POST MAPLE—ALDER—RUBBERWOOD
AVAILABLE IN RED OAK AND CHERRY—SPECIAL ORDER
POST-A
Full Post 3-1/2" x 3-1/2" x 35-1/4"
Half Post 1-3/4" x 3-1/2" x 35-1/4"
Also available in 42" height
POST-C POST-G POST-M
21
POST-D
DRAWER SLIDE SYSTEMS
P/N Product Description Carton Qty.
DC229-9 9” Soft Close Undermount Slide, Full Ext. 6 pr.
DC305-12 12” Soft Close Undermount Slide, Full Ext. 6 pr.
DC381-15 15” Soft Close Undermount Slide, Full Ext. 6 pr.
DC457-18 18” Soft Close Undermount Slide, Full Ext. 6 pr.
DC533-21 21” Soft Close Undermount Slide, Full Ext. 6 pr.
Brazos Soft Close Undermount Slide.
DC001 Rear Sockets -
DC3010SC18N 18” Soft Close Ball Bearing Slide, Full Ext. 10 pr.
DC3010SC20N 20” Soft Close Ball Bearing Slide, Full Ext. 10 pr.
DC3010SC22N 22” Soft Close Ball Bearing Slide, Full Ext. 10 pr.
100 lb Soft Close Ball Bearing Slide, Full Extension.
DC3600-18 18” 75 lb. Soft Close Ball Bearing Slide, Full Ext. 35mm. 10 pr.
DC3600-20 20” lb. Soft Close Ball Bearing Slide, Full Ext. 35mm. 10 pr.
DC3600-22 22” 75lb. Soft Close Ball Bearing Slide, Full Ext. 35mm. 10 pr.
75 lb Ball Bearing Slide, Full Extension.
22
23
24
25
26
27
28
The CUSHION CLOSE Benefits Include:
Heavy Duty Hinge Cup-to-Arm Connection with 6 Laminated Steel Linkage Connectors.
Multiple Cam Adjustments.
Full Overlay, Half Overlay and Inset Hinges.
Easy Clip-On of Hinge-to-Baseplate.
Common Baseplates for Cushion Close, Free Swing and Self Close Applications.
Numerous Baseplates for Different Overlays.
CONCEALED HINGES
P/N Product Description Carton Qty.
243-1016 110 Degree Clip Cushion Hinge, Full
OL, w/ 8mm Dowels. 250
243-1017 110 Degree Clip Cushion Hinge, Half
OL, w/ 8mm Dowels. 250
243-1018 110 Degree Clip Cushion Hinge, In-
set, w/ 8mm Dowels. 250
243-1019 110 Degree Clip Cushion Hinge, Full
OL, w/o Dowels. 250
243-1020 110 Degree Clip Cushion Hinge, Half
OL, w/0 Dowels. 250
243-1021 110 Degree Clip Cushion Hinge, In-
set, w/o Dowels. 250
Clip-On Cushion close Hinge With Cam Adjustable Arm, 35mm CUP, 45mm C/C.
243-2020 Basic Steel Mounting Plate, 0mm, w/
14mm Euro Screws. 250
243-2021 Basic Steel Mounting Plate, 2mm, w/
14mm Euro Screws. 250
243-2022 Basic Steel Mounting Plate, 4mm, w/
14mm Euro Screws. 250
243-2031 Basic Steel Mounting Plate, 0mm, w/
12mm Euro Screws. 250
Euro Mounting Plates For Clip-On With Euro Screws
P/N Product Description Carton Qty.
243-2023 Cam Adjustable Mounting Plate, 250
243-2024 Cam Adjustable Mounting Plate, 250
243-2025 Cam Adjustable Mounting Plate, 250
Euro Cam Adjustable Mounting Plates For Clip-On*
*Attach with #6X5/8” Wood Screws 29
Ask your Brazos Sales Rep for a full Catalog!
Locks Grommets Convenience Hardware
Retractable Door Hardware Specialty Hinges
Castors
Pulls
Locking Lid Supports Pantry Pullouts
243-2026 Cam Adjustable Mounting Plate, 0mm, w/ 14mm Euro Screws. 250
243-2027 Cam Adjustable Mounting Plate, 2mm, w/ 14mm Euro Screws 250
243-2028 Cam Adjustable Mounting Plate, 4mm, w/ 14mm Euro Screws 250
Euro Cam Adjustable Mounting Plates For Clip-On With Euro Screws.
P/N Products Description Carton Qty.
243-2029 Face Frame Mounting Plate, 0mm, w/o Screws. 250
243-2030 Face Frame Mounting Plate, 3mm, w/o Screws. 250
Steel Face Frame Mounting Plate For Clip-On*
P/N Product Description Carton Qty.
243-2032 Cam Adjustable Face Frame Mount-ing Plate, 0mm, w/o Screws. 250
243-2033 Cam Adjustable Face Frame Mount-ing Plate, 3mm, w/o Screws. 250
Zinc Alloy Cam Adjustable Face Frame Mounting Plates For Clip-On*
243-2017 Basic Steel Mounting Plate, 0mm, w/o Screws. 250
243-2018 Basic Steel Mounting Plate, 2mm w/o Screws. 250
243-2019 Basic Steel Mounting Plate, 4mm w/o Screws. 250
Euro Mounting Plate For Clip-On*
243-1041
110 Degree On Hinge, Self Close Full Overlay w/ 8mm Dowels. 250
243-1042 110 Degree On Hinge, Self Close Full Overlay without Dowels. 250
243-1043 110 Degree On Hinge, Free Swing Full Overlay with 8mm Dowels. 250
243-1044 110 Degree On Hinge, Free Swing Full Overlay without Dowels. 250
Clip-On Self Closing & Free Swinging Hinges With Cam Adjustable Arm, 35mm CUP, 45mm C/C
CONCEALED HINGES
30
31
ROUTER BITS - SAW BLADES - SHAPER CUTTERS - BORING BITS
32
33
34
FASTCAP PRODUCTS SPOTLIGHT
Ask Your Sales Rep for a Full Line 2012 FastCap Catalog! 35
36
37
LIVE EDGE LUMBER SLABS
CALL FOR QUOTES AND PICTURES OF OUR DIFFERENT OFFERINGS
You can view them on our website www.brazosfp.com
FINISHED OR
UN-FINISHED OAK, WALNUT, MAPLE, MESQUITE, PECAN,
CEDAR, ASH, HICKORY, CHERRY
OTHERS SPECIES AVAILABLE
Phone 972 602 1777 Fax 972 602 0224 Toll Free 800 772 2777
2760 N. Great Southwest Pkwy Grand Prairie TX 75050 Web site www.brazosfp.com
HARDWOOD LUMBER SERVICES S4S – S2S – SLR - CUSTOM MILLING – CUSTOM MOULDING
Will Call Hours 7:00am - 5pm Mon. - Fri. Phone Hours 7:00am - 5pm Mon. - Fri.
Next day delivery cut off time - 3:00 pm
Call Our Sales Teams
Adam Tyler Randy Smiley [email protected] [email protected]
Michael Ownby Greg Jepson [email protected] [email protected]
Kenny Pence Ron Wilson [email protected] [email protected]
Danny Reddick [email protected]