BPT Specialist Catalogue 2015

2015/16

Welcome to the 2015/16

Introduction

This is the place where you’ll find those unique, hard-to-find tools that do specialist trade & DIY jobs. From skip ramps and block splitters to access equipment and tar boilers you’ve got the industry’s widest selection of specialist branded products in one handy booklet.

DISCLAIMER: The Company’s standard terms & conditions apply and are available upon request. All product descriptions are correct at the time of printing. Images are for guidance only and do not necessarily represent the goods on offer. The company reserves the right to modify products and withdraw promotions without prior notice.

All promotional and value-added FOC items are subject to stock availability, and may differ occasionally from those advertised. The Company endeavours to ensure that the information in this catalogue is correct, but does not accept any liability for any error or omission herein. All rights are reserved. No part of this publication may be reproduced or transmitted in any form without written permission of the copyright holder.

Full terms & conditions are available upon request.

Specialist Equipment Directory

Contents

Battery Charging Unit 03

Tile Cutters 08

Damp Proofing 07

Skip Ramp / Barrow 06

Ladders & Access 29

Sprayers 05

Manual Handling 28

Gas Torches 14

Roofing Tools 16

Pump Solutions 18

Transformers & 24Power Splitters

Mixers 13

BPT Site Equipment 04

RCD Plugs & Sockets 24

Gas Cylinder Cages 15

Specialist Equipment Directory B

atte

ry C

harg

ing

Uni

t

10 Door Charging Unit 6 Door Charging Unit

Part No: S10400 Part No: S10450

Specification

• Features 10 secure lockers, each with: - Coin return locking - 2-gang RCD protected 13A outlets - Numbered keys for easy ID - Individual locker venting • Integral management unit with: - MCB protected distribution unit - Hasp lock: padlock and 2 keys - 3M lead with 230V 16A plug - Manager instructions and guide

Specification

• Features: 6 secure lockers, each with: - key operated cam lock - 2-gang RCD protected 13A outlets - Numbered keys for easy ID - Individual locker venting

• Integral management unit with: - MCB protected distribution unit - Hasp lock: padlock and 2 keys - 3M lead with 230V 16A plug - Manager instructions and guide

Secure Charging

Features

01

Coin Return Locking (10 Locker verison only)

02

Individually Numbered

03

NEW

003

Manual Tyrolean Machine

Part No: B01001

Specification

• Designed to apply textured coatings to interior and exterior walls • Easy to use • Large capacity plastic body • Replaceable parts

Double Suction Lifter

Part No: D90012

Triple Suction Lifter

Part No: D90013

Specification

• Plastic body • Rubber suction clips • Capable of lifting 100Kg in weight

Specification

• Plastic body • Rubber suction clips • Capable of lifting 150Kg in weight

SC4 Block Splitter

Part No: C21400

Specification

• Max cut: 12" x 4.5" • Easy cutting action operation • Cam lever operation • Accurate cuts every time • Long life blades • Heavy-duty construction

Site Equipment

BP

T S

ite Eq

uipm

ent

004

Sp

raye

rs

Part No: F15350

8ltrGMCS 8 Compression Sprayer SS10 Stainless Steel Chemical Sprayer

Part No: ZF15200

GMCS 20 Compression Sprayer

Part No: ZF15300

20ltr20ltr

Specification

• Tough plastic construction • Easy pumping action • Aluminium spray lance • Adjustable nozzle for precise spraying • Weight 2Kg (empty)

Specification

• 1.2m flexible rubber hose• Complete with shoulder strap• Integral safety gauge• Stainless steel tank• Brass spray lance with adjustable nozzle

Specification

• Robust plastic body • Brass compression chamber • Brass spray lance • Adjustable nozzle for accurate spraying • Weight 3Kg (empty)

005

Hold-fast clamp Recessed wheel channel Pitted walkway Patented wheel trap & pivot bar

Part No: B40003 Part No: BEAGVPP

3M Skip Ramp Builders Barrow

Specification

• Faster load capability • Lightweight construction • Patented design • Easy to store • No maintenance (no moving parts) • Safe working load up to 300Kg • Length 3M • Weight 35Kg

Specification

• 85L Heavy-duty press pan • Tubular frame • Galvanised• Puncture proof wheel

Skip

Ram

p / B

arrow

Features

006

Ensign DPC 4 Way Pump

Part No: 110V K120110 240V K120240

Manifold Assembly Manifold Assembly

Part No: K201630 Part No: K201625

Snap Fit Extension Hose

Part No: 10M K251001 15M K251501Part No: 110V K121110 240V K121240

Ensign DPC 4 Way Pump 10in Manifold 110V & 240V

110V & 240V

10M & 15MBrown Flexi Plugs

Part No: 10kg K40001 1kg K40011

1Kg & 10Kg

ENSIGN

Specification

• C/W 4 x 10in Tap Rods• 4-way manifold for use with the damp proofing machine• Assembled using polyurethane non-hardening hose• Includes a brass manifold block

Specification

• C/W 6 x 10in Tap Rods• 6-way manifold for use with the damp proofing machine• Assembled using polyurethane non-hardening hose• Includes a brass manifold block

Specification

• Polyurethane non-hardening extension hose• Snap fitting

Specification

• 1kg/10kg Pack of flexiheads

Specification

• Damp Proofing Kit 4way• Hypro twin piston pump head• Suction and return hose with fitted strainer• Power take-off point for drill or breaker• Full wrap round frame for protection• 4 way manifold complete with rods

Specification

• Hypro twin piston pump head• Suction and return hose with fitted strainer• Independent on/off switch• Power take-off point for drill or breaker• Full wrap round frame for protection• Carry handle

Dam

p P

roo

fing

007

Tile C

utters

Versatile Power Pro 900 Bridge Saw110 & 230V

610mm 435mm 35mm

The world’s leading supplier of TILING & FLOORING INSTALLATION EQUIPMENT

800W Bridge Saw230V

Part No: 103620

Specification

• Super quiet induction motor 800w• Diagonal tile cuts from 0–45°• Diamond blade with continuous rim for clean cuts Ø200mm• Constant speed for smooth cuts• Water tray with drain plug for easier cleaning• Removable stand

StraightCuts

ProfileCuts

Irregular Angles

Including45°

45°

Mitre Cuts

Straight, Angle & Mitre Cuts...

StraightCuts

ProfileCuts

Irregular Angles

Including45°

45°

Mitre Cuts


620mm 440mm 35mm

Specification

• Induction motor 900w• Diagonal tile cuts from 0–45°• Direct drive motor has a thermal overload protection• Oversized ‘bench style’ slotted aluminium cutting table with integral drainage• Dual water feed increases blade life• Large water tray with submersible pump• Built–in carry handles

Part No: 110V 103440 230V 103450

008

Tile

Cut

ters

Part No:103420 Part No:103421

General Purpose Diamond Blade Ø180mm & Ø200mm

Versatile Power Pro 750 Wet Saw 230V

Versatile Power Pro 750 Wet Saw110V

Specification

• 750w Direct drive produces a constant cutting speed for ultra smooth cuts • Ø180mm x 16mm diamond blade with continuous rim for extra clean cut • Extra large cast aluminium cutting table for supporting oversize tiles• Cutting table tilts for 15˚, 30˚ and 45˚ mitres• Water cooling system with large with large reservoir and integral drainage• Transparent wheel guard with variable height adjustment • Moulded plug with 1.5m cable• Convenient built- in carry handle and cable tidy• Black carrier is reversible for both 16mm and 22mm bore sizes

Specification as per Versatile Power Pro 750 Wet Saw 230V.

Replacement diamond blade, suitable for cutting ceramic, terracotta, quarry, slate, marble, masonry concrete and stone tiles.

StraightCuts

ProfileCuts

Irregular Angles

Including45°

45°

Mitre Cuts


ALL ALL 25mm

ALL ALL 25mm

Part No: Ø180mm Blade 103407, Ø200mm Blade 103411 -

Specification

009

Tile C

utters


Clinker Xl 750 Pro Tile CutterClinker Xl 900 Pro Tile Cutter

Part No: BRUTUS750Part No: BRUTUS900

Specification

• High precision cutting head with replaceable tungsten carbide wheel• Cutting head carriage with ball bearings for greater accuracy and easier use• Table extensions to support larger format tiles• Large graduated swivelling cutting guide• Replacement cutting wheel available• Comfortable co-moulded handle• Wheels for easy transport• Shock absorbing trays• 2 year guarantee• Carrying handle

Specification

• High precision cutting head with replaceable tungsten carbide wheel• Cutting head carriage with ball bearings for greater accuracy and easier use• Table extensions to support larger format tiles• Large graduated swivelling cutting guide• Replacement cutting wheel available• Comfortable co-moulded handle• Wheels for easy transport• Shock absorbing trays• 2 year guarantee• Carrying handle

900mm 635mm 20mm 750mm 530mm 20mm

Double Tray 900mm Single Tray 750mm

Spare Parts Order Part No Qty

Replacement cutting wheel CXLWHEEL 1


Replacement cutting wheel CXLWHEEL 1

010

Tile

Cut

ters600 Manual Tile Cutter630 Heavy Duty Tile Cutter

Part No: 102370Part No: 102380

Specification

• Simple score and snap operation• Tungsten carbide cutting wheel• Straight cuts on tiles up to 600mm square• Diagonal cuts also possible on tiles up to 425mm square tiles• Suitable for cutting wall, floor and ceramic tiles up to 12mm thick

Specification

• Compact and lightweight, with a rigid aluminium construction and adjustable cutting guide• Cuts tiles up to 630mm long, diagonal cuts on tiles up to 445mm square• Suitable for cutting wall, floor and ceramic tiles up to 13mm thick• Simple score and snap operation• Tungsten carbide cutting wheel

630mm 445mm 13mm 600mm 425mm 12mm


Replacement cutting wheel 102385 1


Replacement cutting wheel 102375 1

011

Tile C

utters

Astro Pro Masonry, Concrete, Brick & Tile Cutter230V

Part No: WSBMC720

Specification

• Powerful 720w industrial motor• Adjustable cutting depth - can be locked into place• Diagonal cutting guide• Water cooling system• Supplied with an anti-shock carry case, ideal for storage and transportation• Supplied with 2x Ø200mm blades:• 1x diamond blade with continuous rim for cutting tiles• 1x turbo disc for cutting: bricks, concrete tiles, flat tiles, roof tiles, terracotta, slate floors and • Thin concrete, stone, marble granite, sandstone (dry or wet cut)

General Purpose Diamond Blade Ø200mm

Part No: 103411

Replacement diamond blade, suitable for cutting ceramic, terracotta, quarry, slate, marble, masonry concrete and stone tiles.

ALL ALL 45mmStraightCuts

ProfileCuts

Irregular Angles

Including45°

45°

Mitre Cuts


Includes robust, protective carry case for ease of transportation

012

Mix

ers

1400w Power Mixer230V & 110V

1600w Power Mixer Plus230V

Part No: MIXPLUS

Specification

• Specially designed powerful motor• 2 Gears for high performance• Electronically controlled variable speed• Lockable speed control for continuous operation• Supplied in storage case• Paddle - Ø140mm• 1400w for mixing up to 120L• 2 Gear• Speed (no load) 300-700rpm

Specification

• Powerful high torque motor for more efficient mixing• Ergonomic handle to minimise fatigue• Variable speed for greater control• Safety on/off switch with lock-on function for continuous running• Thermal overload protection for increased safety• Robust carry case for ease of transportation• Paddle - Ø140mm• 1600w for mixing up to 120L• 2 Gear• Speed (no load) 300-700rpm


Part No: 230V MIX1400 110V MIX1400IND

Adhesive Mixer PaddleØ120mm & Ø140mm

Mixer Stand with Bucket

Part No: Ø120mm MIXADH120 Ø140mm MIXADH140

Part No: MIXSTBUCK

Specification

• Suitable for use with MIX1400/IND and MIXPLUS• Length 600mm• Designed to mix sticky and viscous materials e.g. tile adhesive, bonding mortar, jointing compound, ready mixed plaster, floor screed, fillers etc.

Specification

• Stand suitable for use with Vitrex Mixers• Effortless mixing for large quantities• Locking system provides multiple positions• Sturdy wheels allow for easy positioning• Folds for ease of storage and carrying

Mixes from bottom up

013

Specification • Regulation Trigger• 3 interchangeable burners Ø 10 – 14 – 17 mm • 5 m rubber hose PVC 3/8” 3/8” • Burner Ø 10 mm = inject 0.15 mm POWER 1 kW (lab test 4 bar)• Burner Ø 14 mm = inject 0.20 mm POWER 2 kW (lab test 4 bar)• Burner Ø 17 mm = inject 0.24 mm POWER 2.75 kW (lab test 4 bar)

Specification • Regulation Trigger• Neck 100mm long• Burner Ø 45 mm• 5 m rubber hose PVC 3/8” 3/8” • Burner Ø 45 mm = inject 1.00 mm POWER 53 kW (lab test 4 bar)

Specification • Regulation Trigger• Neck 600mm long • Turbo burner Ø 60 mm • 5 m rubber hose PVC 3/8” 3/8” • TURBO Burner Ø 60 mm = inject 1.50 mm POWER 75 kW (lab test 3 bar)

Specification • Regulation Trigger• Neck 600mm long • 2 x turbo burner Ø 60 mm • 5 m rubber hose PVC 3/8" 3/8" • TURBO Burner Ø 60 mm = inject 1.50 mm POWER 75 kW X 2 pcs (lab test 3 bar)

Specification • Regulation Trigger• Neck 600mm long • 4 x turbo burner Ø 45 mm • 5 m rubber hose PVC 3/8” 3/8” • TURBO Burner Ø 45 mm = inject 1.20 mm POWER 42 kW X 4 pcs (lab test 3 bar)

Specification • Regulation Trigger• Neck 600mm long • 3 x turbo burner Ø 50 mm• 5 m rubber hose PVC 3/8” 3/8” • TURBO Burner Ø 50 mm = inject 1.40 mm POWER 44 kW X 3 pcs (lab test 3 bar)

Gas To

rches

600mm Quad Head Torch

Part No: B24445

Plumber’s Torch

Part No: B21115

200mm Single Head Torch

Part No: B21120 Part No: B22160

600mm Single Head Torch

600mm Double Head Torch

Part No: B23260

600mm Triple Head Torch

Part No: B23360

014

Gas

Cyl

ind

er C

ages

Part No: See below

Gas Cylinder Cages

Gas Cylinder Cages

B50010 Gas Cylinder Cage GC05 Accepts 3 x 19kg cylinders 900mm high x 1000mm wide x 500mm deep 50 x 50 x 3mm Weld Mesh Weight: 50kgB50020 Gas Cylinder Cage GC15 Accepts 6 x 19kg cylinders 1700mm high x 1000mm wide x 500mm deep 50 x 50 x 3mm Weld Mesh Weight: 80kg Fixed Internal ShelfB50030 Gas Cylinder Cage GC20 Accepts 4 x 47kg cylinders 1800mm high x 900mm wide x 900mm deep 50 x 50 x 3mm Weld Mesh Weight: 80kgB50040 Gas Cylinder Cage GC25 Accepts 9 x 19kg cylinders 1200mm high x 1200mm wide x 1200mm deep 50 x 50 x 3mm Weld Mesh Weight: 60kgB50050 Gas Cylinder Cage GC30 Accepts 9 x 47kg cylinders 1800mm high x 1200mm wide x 1200mm deep 50 x 50 x 3mm Weld Mesh Weight: 90kgB50060 Gas Cylinder Cage GC35 Accepts 10 x 47kg cylinders 1800mm high x 1800mm wide x 900mm deep 50 x 50 x 3mm Weld Mesh Weight: 100kgB50070 Gas Cylinder Cage GC40 Accepts 15 x 47kg cylinders 1800mm high x 1800mm wide x 1200mm deep 50 x 50 x 3mm Weld Mesh Weight: 110kgB50080 Gas Cylinder Cage GC50 Accepts 25 x 47kg cylinders 2000mm high x 2000mm wide x 2000mm deep 50 x 50 x 3mm Weld Mesh Weight: 140kgB50090 Gas Cylinder Cage GC55 Accepts 24 x 47kg cylinders 1800mm high x 2400mm wide x 1800mm deep 50 x 50 x 3mm Weld Mesh Weight: 140kg

Specification • Hinged door with hasp and Staple• Fixing points for bolting to solid surface• Supplied Flat Packed with fixings• Includes H&S Signage

• Size: 1700 x 880 x1735mm (L x W x H) • Weight: 130Kg• Manufactured from mild steel sections between 3 & 5mm thick• Covered with 2” x 2” 10g mild steel, copper coated weld mesh• Iron phosphated pre-treatment and powder coated • Comes with signs• Flat Pack: convienient for easy storage flat pack design• Dimensions: - Body 62.6Kg - Lid 14Kg - 2x doors 10.1Kg & 12.5Kg - 2x Internal shelves (735 x 750mm) 7.5Kg each

015

Part No: S10360

Fold Away Gas Cage

Part No: B18402

Regulator

Specification

• 0-4 bar regulator

Part No: See Below

5gl, 10gl, 15gl, 25gl, 40gl

Tar Boiler Kit Tar Boiler Kit (with tap)

Part No: See Below

Tar Boiler Site Trailer

Part No: 25gl B60050 40gl B60600

10gl, 15gl, 25gl

Specification

• Removable inner tank• Fully enclosed burner bracket • Adjustable 0-4 bar regulator• 5m of armoured hose

Specification

• Removable inner tank• Fully enclosed burner bracket • Heavy duty 10-25 gallon burner• Adjustable 0-4 bar regulator• 5m of armoured hose

B11051 5 gl Kit (without tap)B11102 10 gl Tar Boiler Kit (without tap) B11152 15 gl Tar Boiler Kit (without tap) B11252 25 gl Tar Boiler Kit (without tap) B11253 40 gl Tar Boiler Kit (without tap)

B12102 10 gl Tar Boiler Kit (with tap)B12152 15 gl Tar Boiler Kit (with tap) B12252 25 gl Tar Boiler Kit (with tap)

• Single axle construction • Un-braked• Chassis and integral • Frame manufactured from rolled hollow section • Gas bottle storage complete with safety chain and heatshield

• Fitted with lighting board • Tow coupling - eye or ball as required • Jockey support wheel• 2 x prop stands• Mudguards

25gl & 40gl

Specification

Ro

ofi

ng To

ols

016

Part No: Rubber B18500 Armoured B18600

5M Rubber Hose

Part No: B15375 Part No: B18800

Tar Boiler Ladle Standard Over Spill Tray

Specification

• 5M in length• 6mm thickness• Rubber Hose; for use with torches only• Armoured Rubber Hose; for use with torches and tar boilers

Spouted Bucket

Part No: B15130

Specification

• Made from reinforced steel• 3 Gallons

Specification

• Made from reinforced steel• 3 Gallons

Part No: B15232

Pouring Can Compound Bucket

Part No: B25070

Specification

• Made from reinforced steel

Specification

• Made from stainless steel• 3 Gallons

Rubber or Armoured

3gl

3gl

Specification

• British made overspill tray to fit any small (10gl), medium (15gl) large (25gl) boiler• Made from 2mm steel

1200mm x 900mm

3gl

Ro

ofi

ng T

oo

ls

PRO ROOFING KIT for expert results

017

Pum

p S

olutio

ns

Pump Solutions

Part No. Manual/Auto inlet/outlet (mm) kW flow (l/min) head (mtrs) w x l x h (mm) Dry weight (kgs)

MIZAR30A 1 1/4" Pump, Auto 240VMIZAR30A1 1 1/4" Pump, Auto 110VMIZAR30M2 1 1/4" Pump, Manual 240VMIZAR30M1 1 1/4" Pump, Manual 110V

The Mizars are 304 stainless steel pumps for domestic, trade and industrial use. With two motor sizes to select from, models are available with or without a float switch, and in 110 volts or 230 volts. Standard model takes soft solids up to 10mm°.

A submersible pump for use in narrow pits and sumps, which may be shallow or contain low levels of clean water.

It has a dual control switch, which lets the internal float switch to be switched to “on” or “off” by the user, to enable automatic level control or for manual drainage.

Model MS is a basic, fully rotary, cast iron and brass hand pump for diesel, paraffin and oil transfer.

Supplied with 25mm outlet spout, 1000mm (3 part) rigid riser tube, barrel adaptor, strainer stand and operating handle.

It should not pump water, petrol, chemicals, solvents or products with a low flash point.

ENM pumps are self-priming with bronze bodies and single impellers.

With a forward and reverse switch for filling and emptying duties they are good, general-purpose, portable pumps for circulating and transfer of water, sea-water, juices, gas oil (“red diesel”), bio-fuel, transformer oil and mild chemicals.

1" Transfer Pump

Part No: 110V ENM25 240V ENM252

1¼" Submersible Sump & Drainage Pump

Part No: See Below Part No: EGO500

110V & 240V1" Submersible Sump Pump

Part No: MS25

Oil/Diesel Barrel Pump

Pump Specification

MIZAR30A A 32 0.25 150 7 Ø154x234 5.2MIZAR30A A 32 0.25 150 7 Ø154x234 5.2MIZAR30M M 32 0.25 150 7 Ø154x234 4.9MIZAR30M M 32 0.25 150 7 Ø154x234 4.9EGO 500 A/M 25 0.47 170 7.5 168x206x280 3.6MS25 n/a 25 n/a 25 n/a 130x220x1265 4.5ENM25 n/a 25/25 0.45 55 13 141x318x190 9.0ENM252 n/a 25/25 0.45 55 13 141x318x190 9.0

230V Dual control

018

Pum

p S

olu

tio

ns

6M & 30M

Part No: See Below

Pump Leads

Part No: 999-000-010

Suction & Delivery Hose ¾"- 3"

Part No: See Below Part No: See Below Part No: See Below

Hose Coupling Hose Joiner

Cam Coupling

Part No: See Below

Tin Strainer

137119 6M Coil ¾"P10112 6M Coil 1"P10117 6M Coil 1¼"P10122 6M Coil 2"P10132 6M Coil 3"137119.3 30M Coil ¾"137125.3 30M Coil 1"137132.3 30M Coil 1¼"137150.3 30M Coil 2"137180.3 30M Coil 3"

Specification General purpose hose for inlet use/suction side of engine driven pumps or for general discharge. Rigid but flexible, shock resistant, embedded nylon spiral-helix reinforced.

Specification Quick release hose couplings in aluminium overcome the problems of cross threading and lost washers associated with threaded connections on engine pumps. The threaded part is permanently attached to the pump and the two lever part is permanently attached to the hose for a quick conection and an air tight seal.

Specification Strainer in tin, for use on suction hose of engine driven pumps to keep debris out that may clog/damage the pump.

Specification Replacement sub pump leads in HO7RNF rubber 1.5mm. Will fit to Tsurumi, JS and Koshin 110V and 230V submersibles.

13402504 Cam Coupling, Part A 1" 13405004 Cam Coupling, Part A 2"13408004 Cam Coupling, Part A 3" 13412504 Cam Coupling, Part C 1"13415004 Cam Coupling, Part C 2" 13418004 Cam Coupling, Part C 3"

13602504 Tin Strainer 1"13605004 Tin Strainer 2"13608004 Tin Strainer 3"

SpecificationAluminium tube with ridges for joining two lengths of pipe together.

Specification Swivel couplings for attaching a hose to a threaded fitting on a pump.

13012502 Hose Coupling / Brass 1"13015003 Hose Coupling / Iron 2"13018003 Hose Coupling / Iron 3"

13382504 Hose Joiner 1" 13385004 Hose Joiner 2"13388004 Hose Joiner 3"

019

10M & 100M

12V DC

Pump Solutions

Pum

p S

olutio

ns

1” Diesel Transfer (Low Voltage)

Part No: DCC

Float Switch

Part No: 999-000-111 Part No: See below

Layflat Hose

Part No: 110V COUGAR 230V COUGAR2

1” Diesel Transfer Kit

Pressure Test Pump

Part No: 25BAR PT25 50BAR PT50

Dirty Water Centrifugal Pump

Part No: See below

SpecificationFloat switch to control water levels. For retro-fitting to Tsurumi, JS and Koshin 110V and 230V submersibles.

SpecificationGeneral purpose hose for open end discharge of water on engine pumps, submersible pumps and hand pumps. Soft, flat and flexible, yarn reinforced construction.

SpecificationThe Cougars are self-priming pumps for pumping diesel and biodiesel. The motors have rocker switches, internal filters (for trapping debris) and by-pass valves (for 2 minutes use against a closed nozzle). Kit includes a manual nozzle, hose fittings, strainer, hose and easy carry frame.Motor: 0.37kW Flow: 50 l/min Head: 20 mtrs Dimensions(mm) & weight in frame: 250 x 310 x 270 & 8.5 kgsIt must not pump water, petrol high viscosity liquids, chemical, solvents or any low flash point liquid.

SpecificationThe LC pumps are self-priming, centrifugal pumps with 4 stroke Loncin petrol engines, by Loncin of China. All models have aluminium pump housings for portability and ceramic mechanical seals, cast iron volutes, cast iron impellers and oil alerts for reliability.

SpecificationThe PT models are pressure test pumps for leak testing in water pipe systems. Suitable for pressurised plastic pipe plumbing and central heating systems. The reservoir is in powder coated steel with ½” male BSP connectors, heavy duty handle and supplied complete with a con-nector hose. Not suitable for gas pipe testing.

P10210.5 1” Layflat Hose - 100M Roll P10211 1” Layflat Hose - 10M LengthP10212.5 1 1/4” Layflat Hose - 100M Roll P10213 1 1/4” Layflat Hose - 10M LengthP10220.2 2” Layflat Hose - 100M Roll P10220.5 2” Layflat Hose - 10M LengthP10222 3” Layflat Hose - 100M RollP10223 3” Layflat Hose - 10M Length

LC25 1” Dirty Water Centrifugal Pump LC50 2” Dirty Water Centrifugal PumpLC80 3” Dirty Water Centrifugal Pump

25BAR, 50BAR

SpecificationThe DCC is a low voltage (D.C.) self-priming pump for pumping diesel and biodiesel only. The motor has a duty cycle of 30 minutes. It has a carry handle and is supplied with a 2 metre battery cable, crocodile clips, integral fuse and a switch. Included is a pumping kit that comprises hose, nozzle and connectors.Motor: 22 amps Flow: 30 l/min Head: 10 mtrs Dimensions (mm) & weight: 112 x 200 x 145 & 4.0 kgsIt must not pump water, petrol high viscosity liquids, chemical, solvents or any low flash point liquid.

020

Pum

p S

olu

tio

ns

Semi Trash Centrifugal Pump

Part No: 2" TD200HA 3" TD300HA Part No: 2" TDS50HA 3" TDS80HA

SEE TABLE ON PAGE 22 FOR PUMP SPECIFICATION

Part No: 2" TET50HA 3" TE480HA

Diaphragm Pump

2" Submersible Contractor Pump Dirty Water Centrifugal Pump 2" & 3"Auto, Manual, 110V & 240V

2" & 3" 2" & 3"

LB4801A 2” Pump, Auto 110VLB480A 2” Pump, Auto 240VLB480 2” Pump, Manual 110VLB480M 2” Pump, Manual 240V

Specification The TD series are automatic priming, engine driven diaphragm pumps with Honda petrol engines (with oil alert), from Tsurumi of Japan. They have maintenance free gearboxes, surge reduction chambers and an aluminium pump chamber. Capable of dry running. A site trolley is available as an optional extra.

Specification The LB series are heavy duty, yet lightweight, contractor pumps for dirty and abrasive site water. The dual position outlet on the LB480 and LB800, gives the option of either verticle or non kink horizontal pumping. Designed to operate for extended periods in seepage conditions. Available with or without a float switch.

TET50HA 2” Dirty Water Centrifugal Pump - Petrol TE480HA 3” Dirty Water Centrifugal Pump - Petrol

Specification The TE pumps are self priming centrifugal pumps with Honda 4 stroke petrol engines, by Tsurumi of Japan. They have aluminium pump housings for portability, and ceramic mechanical seals, cast iron volutes, cast iron impellers and oil alerts for reliability.

Specification The TDS models are self-priming, centrifugal, semi-trash pumps with Honda petrol engines, by Tsurumi of Ja-pan. They can pump solids up to 20mm in diameter. All models have aluminium pump housings for portability and silicon carbide mechanical seals, cast iron volutes, cast iron impellers and oil alerts for reliability.

Part No: See below

021

Part No: 2" TE350RD 3" TE380RD

2" & 3"1" 110V & 230V1" Submersible Residue Pump

Part No: 110v LSC1.4S 230v LSC1.4S/230

Pump Specification

Dirty Water Centrifugal Pump Dirty Water Centrifugal Pump

Part No: TEM25H

LB4801A A 50 0.48 225 11 Ø187x275 10.80LB480A A 50 0.48 225 11 Ø187x275 10.80LB480M M 50 0.48 225 11 Ø187x275 10.40LB480M M 50 0.48 225 11 Ø187x275 10.40LSC1.4S M 25 0.48 170 11 Ø196x316 12.00LSC1.4S/230 M 25 0.48 170 11 Ø196x316 12.00TEM25H n/a 25/25 GX25 140 40 215x340x270 5.00TET50HA n/a 50/50 GX120 520 32 356x470x350 22.00TE480HA n/a 80/80 GX160 1000 32 375x527x420 27.00TD200HA n/a 50/50 GX120 120 17 610x620x510 39.00TD300HA n/a 80/80 GX160 240 18 740x660x510 46.00TDS50HA n/a 50/50 GX120 780 23 345x470x420 24.00TDS80HA n/a 80/80 GX160 1150 23 370x525x420 27.00TE350RD n/a 50/50 DY23D 600 28 410x505x495 40.00TE380RD n/a 80/80 DY23D 900 28 410x590x510 42.00

Part No. Manual/Auto inlet/outlet (mm) kW/engine flow (l/min) head (mtrs) w x l x h (mm) dry weight (kgs)

LSC1.4S “puddle sucker” is used for pumping dirty site water, from a flat surface down to 1mm. The dual position outlet gives the option of non kink horizontal pumping or vertical pumping with the integral swing check valve also preventing back flow. A tough contractor’s pump designed to operate for extended periods in seepage conditions.

The TEM25H is a self priming centrifugal pump with a Honda 4 stroke petrol engine, by Tsurumi of Japan. It has an aluminium pump housing, volute, impeller and a ceramic mechanical seal.

The TE pumps are self-priming pumps powered by compact Subara-Robin diesel engines. Heavy duty design, yet portable, easy to start up and operate they can pump site water. With good flows and pressure, they are suitable for site use, land drainage and general transfer. Supplied in easy carry frame with strainer and couplings.

Pum

p S

olutio

ns

022

Pump Specification

Sump Pump Trash Pump2", 3", Auto, Manual, 230V, 110V ¾", 1", Auto, Manual, 240V, 110V/ 240V

BPS80A 3/4” Sump Pump, Auto 240VBPS80M 3/4” Sump Pump, Manual 240VBPS100A 1” Sump Pump, Auto 240V BPS100M 1” Sump Pumo, Manual 240VBPS400M110 2” Clean water pump, Manual 110VBPS400M240 2” Clean water pump, Manual 240VBPS400A110 2” Clean water pump, Auto110VBPS400A240 2” Clean water pump, Auto 240V

The BPS range combines excellent lifecycle with value for money performance in domestic and trade applications. Automatic models have a float switch fitted for automated control of water levels i.e. turning on and off when water levels rise and fall in sumps. Manual models do not have a float switch. For drainage and transfer applications - BPS80 and 100 manual versions are capable of pumping water down to 3mm. Constructed in thermoplastic, they are suitable for clean and slightly dirty water.

SV400M110 2” Trash Pump, Manual 0.4kW 110VSV400M230 2” Trash Pump, Manual 0.4kW 230VSV400A110 2” Trash Pump, Auto 0.4kW 110VSV400A230 2” Trash Pump, Auto 0.4kW 230VSV750M110 3” Trash Pump, Manual 0.75kW 110VSV750M230 3” Trash Pump, Manual 0.75kW 230VSV750A110 3” Trash Pump, Auto 0.75 kW 110VSV750A230 3” Trash Pump, Auto 0.75kW 230V

The SV series is a range of submersible pumps, with vortex impellers, for dirty water containing hard solids & fibrous matierials. With cast iron pump casings, base plate and impeller, stainless steel motor frames and thermoplastic head covers (SV750, cast iron). They are well suited to domestic and industrial applications.

BPS80A A 19 0.08 40 4 Ø136x255 2.20BPS80M M 19 0.08 40 4 Ø136x255 1.95BPS100A A 19 & 25 0.10 70 6.5 134x155x250 2.80BPS100M M 19 & 25 0.10 70 6.5 134x155x250 2.50BPS400M110 M 50 0.4 220 9 160x200x365 7.35BPS400M240 M 50 0.4 220 9 160x200x365 7.35BPS400A110 A 50 0.4 220 9 160x200x365 7.50BPS400A240 A 50 0.4 220 9 160x200x365 7.50SV400M110 M 50 0.4 350 8 160x215x420 11.30SV400M230 M 50 0.4 350 8 160x215x420 11.30SV400A110 A 50 0.4 350 8 160x215x420 11.55SV400A230 A 50 0.4 350 8 160x215x420 11.55SV750M110 M 80 0.75 425 11 165x265x440 17.15SV750M230 M 80 0.75 425 11 165x265x440 17.15SV750A110 A 80 0.75 425 11 165x265x440 17.40SV750A230 A 80 0.75 425 11 165x265x440 17.40

Manual/Auto

Outlet (mm) kW Flow (l/min)

Head (mtrs)

w x l x h (mm)

Dry weight (kgs)

Part No.

BPS100A

SV400M SV750A

Part No: See below

BPS400A

Pum

p S

olu

tio

ns

APP PUMPS

Part No: See below

APP PUMPS

023

Part No: E13220Part No: E205100 Part No: 110v E13200, 230v E13210

Spider Ball - Power Distribution Unit

Specification > Redistribution of 110V site power to use 110V appliances > Durable nylon/rubber casing provides extra protection for use in harsh conditions > Recessed outlets prevent them from being sheared off in harsh environments > Useful extra features include visible power-on indicators

and cable tidy with securing strap> Outlets 4x 16A

Spider Pod - Power Splitter

Specification > High impact, lightweight nylon shell for use in tough applications > Flexible, multi-directional outlets supply power to multiple tools > Compact design allows for easy trasportation and storage> Outlets 4x 16A

Power Pod Transformer

Specification > Perfect for site power conversion from 240V to 110V > Tough rubberised DuPont casing protects against the rigours of site

use and transportation > Recessed outlets prevent them from being sheared off in harsh environments > Power-on indicators for each socket show when tools are powered up

Specification

• Resettable circuit breaker• 2m of cable• Max Wattage of lighting that can

be used is 1666W • Outlets - 2X 16A 1X 32A

110VIn 230V / out 110V 110V, 230V

Transform

ers / Po

wer S

plitters

024

Specification• IP23 rating• Protected by MCB’s• Double wound with safety earth screen• Weight: 45Kg

Specification• IP23 rating• Protected by MCB’s• Double wound with safety earth screen• Weight: 91Kg

5KVA SITE TRANSFORMER

Part No: E203010

Part No: ZE210022Part No: ZE210028

Part No: E205042

3KVA TRANSFORMER 5KVA TRANSFORMER

10KVA AIR COOLED SITE TRANSFORMER

110V

110V 110V

110V

Specification

• Resettable circuit breaker• 2m of cable• Max wattage of lighting that can

be used is 1000W

Specification

• Resettable circuit breaker• 2m of cable• Max Wattage of lighting that can

be used is 1666W • Outlets - 2X 16A 1X 32A

Tran

sfo

rmer

s /

Po

wer

Sp

litte

rs

HIGH QUALITY, CUTTING-EDGE POWER DISTRIBUTION SOLUTIONS

Specification• Resettable circuit breaker• 2m of cable• Max wattage of lighting that can be used is 1666W

025

Specification• 16A Distribution box• 2.5mm cable• Fitted plug• Steel cased• 4x Outlets

Specification• 32A Distribution box• 4mm cable• Fitted plug• Fibreglass case• 6x Outlets

Classic 4-Way Power Distribution Unit

Part No: E13115

Part No: E13111Part No: E13104

Part No: E13125

4-Way Power Distribution Unit 6-Way Power Distribution Unit

2-Way Power Distribution Unit

110V

110V 110V

110V

Transform

ers / Po

wer S

plitters

HIGH QUALITY, CUTTING-EDGE POWER DISTRIBUTION SOLUTIONS

Specification• 16A Distribution box• 2.5mm cable• Fitted plug• Steel cased• Fitted MCB

Specification• Steel cased• Fitted MCB

026

Specification• 13A RCD wireable plug

Specification• 13A RCD plug & socket

Specification• 13A plug • 16A socket • 1M of arctic blue cable • Inline RCD

Specification• 13A plug • 16A socket • Fibreglass case• 2M cable

Specification• 13A plug • 13A socket • Fibreglass case• 2M cable

Part No: E11090

RCD Plug

Part No: E11070C Part No: E11092 Part No: E11085C

13-13A RCD Unit In-line RCD Unit

RCD Socket

Part No: E11060C

13-16A RCD Unit

RC

D P

lug

s an

d S

ock

ets

027

Part No: ST250/S8

Manual H

andling

Pallet Truck Sack Truck

Part No: T01000.1

Specification• Twin nylon steering wheels• Twin nylon bogey wheels • Durable leak proof hydraulic system• Maximum lifting capacity 2500Kg• Turning radius for manourvrability 210°• Fork length 1100mm• Width over forks 550mm• Weight 85Kg

Specification• Heavy-duty sack truck • 250kg carrying capacity • All tubular frame construction • Standard toe plate• Wheel guards• Solid rubber tyres

028

Part No: See belowPart No: 316515

Aluminium AluminiumTeleguard

Lad

der

s an

d A

cces

sPodium Ladder

DURABLE STABLETOUGH VARIABLE VERSATILE

Product Code

Rungs per section

Platform Size (m)

Height Adjustments

Max Safe Working Height (m)

Load Capacity (kg/stone)

Weight (kg)

316515 4 - 6 6.10 x 4.44 2 3.63 150/23.6 37

Product Code Treads Platform Height (m) Duty Rating (kg/stone)

Weight (kg)

52750300 3 0.91 136/ 21.4 10.3

52750400 4 1.22 136/ 21.4 12.1

52750600 6 1.93 136/ 21.4 15.6

52750800 8 2.44 136/ 21.4 21.3

52751000 10 3.05 136/ 21.4 26.7

Specification• Use in flat slab mode or on stairways• Simple height adjustment rung by rung• Double guardrails and positive locking gate on platform• Deep draining tool tray• Deck lock clip – auto lock• Excellent stabilisation• Robust aluminium chequer plate toeboard• Tough wheels for easy movement around site• Rugged rubber stabiliser overboots• Spring loaded stowage catch• Ladder section alignment bars at both sides

Specification• Available in 3, 4, 6, 8 and 10 tread • Ideal for working at fixed heights, easier to maneuver than scaffolds or lifts• LOCKTOP™ waist-high guard rail securely wraps around work zone• Extra-large standing platform for long standing comfort• EDGE360™ gives protection from every angle with integrated rail shield, EDGE bracing and oversized foot pad• 4X Work Zone allows you to work facing any direction

DURABLE STABLETOUGH VERSATILE NON CONDUCTIVE

029

Specification• Reduces the risk of theft and frees up interior

vehicle space• Includes padlocked for extra security• Fits to most extension ladders• Supplied as a pair• Approx. 0.27m of adjustment

Specification• Fits easily to most extension ladders• Avoid damage to gutters, tiles and windows

Ladder Rack Clamp (Pair)

Part No: 570122

Part No: 300870Part No: 303898

Part No: 570213

Trade 200 Trade 400

Ladder Stay

2 section Aluminium

Steel Steel

2 section Aluminium

Ladd

ers and A

ccess

DURABLE DURABLE TOUGH TOUGH VARIABLE VARIABLE VERSATILE VERSATILE

Product Code

Sections x Rungs

Closed Height (m)

Open Height (m)


Duty Rating (kg/stone)

Weight (kg)

570112 3 x 10 3.08 7.43 7.68 110/17.3 20.99

Product Code

Sections x Rungs

Closed Height (m)

Open Height (m)


Duty Rating (kg/stone)

Weight (kg)

570213 2 x 12 3.69 6.30 6.62 110/17.3 13.29

Specification• High-performance box-section alloy stiles• Easy, push up operation• Slip-resistant square rungs• Rung clips secure together for safe & easy use and

transport• Unique wrap-around top clips fit with smooth-glide

runners for reduce wear and tear

Specification• 30mm-deep square rungs for strength and comfort• Wall wheels to make ladder extension easier• Easy, push up operation• Rung clips secure together for safe and easy use and transport• Unique wrap-around top clips fit with smooth-glide runners for

reduce wear and tear

030

Part No: 310898 Part No: 312898

Odd Job 600 GRP Odd Job 600Aluminium Aluminium

Lad

der

s an

d A

cces

s

DURABLE DURABLE STABLE STABLETOUGH TOUGH COMPACT COMPACT LIGHTWEIGHT LIGHTWEIGHT

Product Code

Folded Size (m) Platform Size (m)

Platform Height (m) Load Capacity (kg/stone)

Weight (kg)

310898 0.73 × 0.38 × 0.18 0.30 × 0.70 0.51 110/17.3 4

Product Code

Folded Size (m) Platform Size (m)

Platform Height (m)

Load Capacity (kg/stone)

Weight (kg)

312898 0.63 x 0.68 x 0.18 0.60 x 0.60 0.51 110/17.3 5.7

Specification• Compact folded dimensions for easy storage• Large non-slip platform• Lightweight and easy to transport• Splayed base for extra stability

Specification• Large non-slip platform• Splayed base for extra stability• Compact folded dimensions for easy storage• Lightweight and easy to transport• Simple to use• Perfect for all odd jobs

031

Birchwood Price Tools Specialist Equipment Directory. Designed and Distributed by Birchwood Price Tools. Birchwood Price Tools is a trading name of the BSS Group Limited. Part No: K56756

Documents

BPT Specialist Catalogue 2015