Upload
faunia
View
61
Download
1
Tags:
Embed Size (px)
DESCRIPTION
BOILER EFFICIENCY. Steam Output. Radiation Loss. Second Pass. Heat Input. ESP. Furnace. Heat Input is Pulverised Coal Heat Output is Superheated Steam. Efficiency Calculations. Standard Applied :- ASME Standard PTC 4.1 Calculation Method :- Loss Method - PowerPoint PPT Presentation
Citation preview
Heat Input
Radiation Loss
Steam Output
BOILER EFFICIENCY
Heat Input is Pulverised Coal
Heat Output is Superheated Steam
Furnace
Second Pass
ESP
Efficiency Calculations
Standard Applied :- ASME Standard PTC 4.1
Calculation Method :- Loss Method
Losses calculated as percentage of INPUT as 100%
Losses in Boilers
1) Loss due to dry flue gas = 4.928%
Furnace
Second Pass
ESPHeat Input
Losses in Boilers Contd.
2) Loss due to Unburnt Carbon = 0.331%
Furnace
Second Pass
ESPHeat Input
Losses in Boilers Contd.
Furnace
Second Pass
ESP
3) Due to Sen. Heat of Bottom Ash = 0.071%4) Due to Sen. Heat of Fly Ash = 0.102%
Heat Input
Losses in Boilers Contd.
Furnace
Second Pass
ESP
5) Radiation Losses = 0.200%
Heat Input
Losses Related to Coal & Ambient Air Quality
6) Loss due to moisture in Fuel = 1.263%
7) Loss due to Hydrogen in Fuel= 5.537%
8) Loss due to Moisture in Air = 0.074%
9) Unaccounted Losses = 1.327%
Total Losses = 13.83%
Data required for Boiler Efficiency Calculations
Unit load MW FW Flow at Econ inlet T/hr Wet bulb Temp 0C Dry bulb Temp 0C Barometric Pressure mmHg Total Coal Flow T/hr Unburnt C in BA % Unburnt C in FA % Radiation & Unaccounted Losses % % Fly ash to Total Ash % % Bottom ash to Total ash %
Data required……….2Proximate Analysis of Coal Air Dry As fired
Moisture % % Ash % % Volatile Matter % % Fixed Carbon % % Gross Cal. Value Kcal/kg Kcal/kg
Ave FG O2 APH in Ave FG O2 APH Out Ave FG CO2 APH in Ave FG CO2 APH Out Ave FG CO APH in Ave FG CO APH Out Ave. FG Temp APH in Ave. FG Temp APH Out Air to APH in Air APH out Total Primary Flow Total Air Flow L Total Air Flow R Design Ambient / Ref air Temp
CalculationsUltimate Analysis As fired Basis
1. Carbon = (Fixed Carbon AD+0.9(Vol Matter AD-14)) *GCV AF/GCV AD
2. Sulphur = 0.4 * GCV AF/GCV AD
3. Hydrogen = Vol.Matter AD*(7.35/(Vol Matter AD+10)- 0.013)* GCV AF/GCV AD
4. Moisture = Moisture AF
5. Nitrogen = (2.1-0.012 * Vol.Matter AD)* GCV AF/GCV AD
6. Oxygen = 100-(Carbon+Hydrogen+Nitrogen+Ash AD+Moisture AD)* GCV AF/GCV AD
7. Ash = Ash AF and 8. Gross Cal. Value=GCV AF
Calculations ….. LossesDry Gas Loss = Sensible heat of dry gas*100/(GCV AF*4.186) %
Carbon in fuel
%
Sulfur in fuel
%
Carbon in ash / kg of fuel
kg/kg coal
Specific Heat of Gas
kg/kg C
Avg. Flue gas temp - APH Out
0C
Unburned C in Ash = Pfa/100*Cfa + Pba/100*Cba
%
C in Ash / Kg of coal =A/100*Cash/(100-Cash)
kg
Total air Flow = A+B
Thr
Ratio SA Flow to Total Air Flow - Fsa/Fta
%
Ratio PA Flow to Total Air Flow = Fpa/Fta
%
Weighted Temp Air In = Tsai*Rsa+Tpai*Rpa0CWeighted Temp Air Out = Tsao*Rsa+Tpao*Rpa0C
Avg. Flue Gas CO2 -APH Out
%
Gross CV
kcal/kg
Weight of Dry Gas = (Ca+S/2.67-100*U)/(12*CO2out)
kg/kg coal
Sensible Heat Dry Gas = Wd*30.6(Tgo-Trai)
kJ/kg
CONTROLLABLE LOSSES 1FOLLOWING LOSSES CAN BE CONTROLLED
1. LOSS DUE TO DRY FLUE GAS
THE DESIGNER GIVES THIS LOSS AT THE FLUE GAS
APH OUTLET TEMP OF 1400C
ANY INCREASE IN THE FGT MORE THAN 1400C WILL BE RESULTING IN MORE LOSSES. THIS TEMP HAS TO BE CONTROLLED BY PROPER CLEANING OF THE FURNACE
CONTROLLABLE LOSSES 2aLOSSES DUE TO THE UNBURNT COAL IN BOTTOM AND FLY ASH.LOSS DUE TO UNBURNT IN BOTTOM ASH
THE DESIGNER GIVES THIS %AGE AS MAX 4.8 % ANY INCREASE IN THIS PERCENTAGE BEYOND THIS WILL RESULT IN MORE LOSSES
IF UNBURNT IN BOTTOM ASH IS MORE, THE CULPRIT IS THE COAL MILL, CHECK THE FINENESS OF PULVERISED COAL. CHECK THE % RETENTION ON 50 MESH. IT SHALL NOT EXCEED 1%.
CONTROLLABLE LOSSES 2bCHECK THE UNBURNT IN FLY ASH SAMPLE TAKEN FROM THE FIRST HOPPER OF ESP/BF
AS PER THE DESIGNER IT SHALL NOT EXCEED 0.8%.
IF UNBURNT IN FLY ASH EXCEEDS 0.8% IT INDICATES INCOMPLETE COMBUSTION DUE TO LESS AMOUNT OF AIRCHECK FOR O2 % AT THE APH FG INLET FOR 2.8%, INCREASE IF NECESSORY TO 3.2%. AGAIN CHECK FOR UNBURNTS IN FLY ASH. SIMULTANIOUSLY CHECK FOR AIR LEAKAGES/INGRESS IN THE SECOND PASS
Losses Calculations
Assumptions:-
1. Fly Ash is 80% of Total Ash.
2. Bottom Ash is 20% of Total Ash
3. Sulphur is 0.4% in Coal
DATA REQUIREDFuel Properties
Proximate Analysis of Coal
Air Dry Basis As Fired basis
Moisture % Moisture %
Ash % Ash %
Volatile Matter % Volatile Matter %
Fixed Carbon % Fixed Carbon %
Gross Cal. Value % Gross Cal. Value %
Data Required contd.
Unit load MW
FW Flow at Econ inlet T/hr
Wet bulb Temp 0C
Dry BulbTemp 0C
Barometric Pressure
Total Coal Flow T/hr
Unburnt Carbon in BA %
Unburnt Carbon in FA %
Data Required Contd.
Ave FG O2 APH in Ave FG CO2 APH in
Ave FG CO APH in Ave FG O2 APH Out
Ave FG CO2 APH Out Ave FG CO APH Out
Air to APH in Temp Air APH out Temp
Total Air Flow L Total Air Flow R
Ave. FG Temp APH in
Ave. FG Temp APH Out
Total Primary Air Flow
GCV Calculations for CoalCalculations of GCV As fired BasisCoal sample is taken as received basis, heated for calculation of A) Total Moisture content = TM% Air Dry BasisThe sample is air dried for removal of surface moisture and burned completely for A) Inherent moisture content = M %B) Ash percentage = A %
GCV Calculations for Coal Contd.
1) Useful Heat Value = 8900 – 138(A%+M%) kcal/kg
2) Gross Calorific Value = (UHV + 3645 – 75.4 M%)/1.466
(Air Dry Basis) Kcal/kg
3) Ash % (As fired basis) = [A %] (100 - TM%)/(100 – M%) %
4) Gross Calorific Value = [GCVAD] (100 - TM%)/(100 – M%)
(As fired Basis) Kcal/kg
5) Net Calorific Value = [GCV] – 10.02M% Kcal/kg
CalculationsWeight of Dry Gas = (Ca+S/2.67-100*U)/(12*CO2out)
Ca = % Carbon in fuel (Ultimate Analysis as Fired)
S = % Sulfur in fuel (Ultimate Analysis as Fired)
A = % of Ash in fuel (Ultimate Analysis as Fired)
Unburned C in Ash = Pfa/100*Cfa + Pba/100*Cba
U = Carbon in ash / kg of fuel=A/100*Cash/(100-Cash)
CO2 Out = Avg. CO2 Flue Gas -APH Out
Sensible Heat Dry Gas = Wd*30.6(Tgo-Trai)