Upload
frsh555
View
152
Download
2
Embed Size (px)
Citation preview
Instruction Manual
25cc/1.5 cu.in. 2-Cycle205 MPH/410 CFMGASOLINE POWEREDBLOWER/VAC
Model No.358.797342
• Safety
• Assembly• Operation• Maintenance
• Parts List
• Espa_ol
WARNING:
Read and follow all Safety Rules and OperatingInstructions before first use of this product.
For answers to your questions about this product:Call 7 am-7 pm, Mon.-Sat., or 10 am-7 pm, Sun.
1-800-235-5878 <.o°,, listed are Central Time)
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
530163801 7/25/03
Warranty Statement 2 Troubleshooting Table 12Safety Rules 2 Emissions Statement 12Assembly 4 Parts List 14Operation 6 Spanish 17Maintenance 9 Parts and Ordering BackStorage 11
FULL TWO YEAR WARRANTY ON CRAFTSMAN ® GAS BLOWERFor two (2) years from date of purchase, when this Gas Blower is maintained,lubricated, and tuned up according to the instructions in the instruction manual,Sears will repair, free of charge, any defects in material or workmanship.This warranty excludes blower tubes, spark plug, and air cleaner, which are ex-pendable parts and become worn during normal use.If this blower is used for commercial purposes, this warranty applies for 90 days fromthe date of purchase. If this Blower is used for rental purposes, this warranty appliesfor 30 days from the date of purchase. This warranty applies only while this productis in use in the United States.WARRANTY SERVICE IS AVAILABLE BY RETURNING THE BLOWER TO THE NEARESTSEARS STORE OR SERVICE CENTER IN THE UNITED STATES.This warranty gives you specific legal rights, and you may also have other rightswhich vary from state to state.Scars, Roebuck and Co., D/817WA, Hoffman Estates, IL 60179
llWARNING: Failure to follow allSafety Rules and Precautions can re-sult in serious injury.KNOW YOUR UNIT* Read your instruction manual care-
fully until you completely understandand can follow all warnings andsafety rules before operating the unit.
• Restrict unit to users who under-stand and will follow all warnings andsafety rules in this manual.
_WARNING: Inspect area beforestarting unit. Remove all debris andhard objects such as rocks, glass,wire, etc. that can ricochet, be thrown,or otherwise cause injury or damageduring operation.Use your unit as a blower for:• Sweeping debris or grass clippings
from driveways, sidewalks, patios, etc.• Blowing grass clippings, straw, or
leaves into piles, around joints, or be-tween bricks.
Use your unit as a vacuum for:• Picking up dry material such as
leaves, grass, small twigs, and bits ofpaper.
• For best results during vacuum use,operate your unit at high speed.
• Move slowly back and forth over thematerial as you vacuum. Avoid forc-ing the unit into a pile of debris asthis can clog the unit.
• Keep the vacuum tube about an inchabove the ground for best results.
PLAN AHEAD• Always wear eye protectionwhen op-
erating, servicing, or performing main-tenance on unit. Wearing eye protec-tion will help to prevent rocks or debrisfrom being blown or ricocheting intoeyes and face which can result inblindness and/or serious injury. Eyeprotection should be marked Z87.
• Always wear foot protection. Do notgo barefoot or wear sandals.
• Always wear respirator or face maskwhen working with unit in dusty envi-ronments.
• Secure hair above shoulder length.Secure or remove jewelry, looseclothing, or clothing with looselyhanging straps, ties, tassels, etc.They can be caught in moving parts.
-2-
• Do not operate unit when you aretired, ill, upset, or if you are under theinfluence of alcohol, drugs, or medica-tion.
• Keep children, bystanders, and ani-mals away from work area a mini-mum of 30 feet (10 meters) whenstarting or operating unit. Do notpoint blower nozzle in the direction ofpeople or pets.
HANDLE FUEL WITH CAUTION, IT ISHIGHLY FLAMMABLE• Eliminate all sources of sparks or
flame (including smoking, openflames, or work that can causesparks) in the areas where fuel ismixed, poured, or stored.
• Mix and pour fuel in an outdoor area;store fuel in a cool, dry, well ventilatedplace; use an approved, marked con-tainer for all fuel purposes.
• Do not smoke while handling fuel orwhile operating the unit.
• Make sure the unit is properly as-sembled and in good operating con-dition.
• Do not fill fuel tank while engine isrunning.
• Avoid spilling fuel or oil. Wipe up fuelspills before starting engine.
• Move at least 10 feet (3 meters)away from fuel and fueling site be-fore starting engine.
• Always store gasoline in a containerapproved for flammable liquids.
OPERATE YOUR UNIT SAFELY
_WARNING: Stop the engine be-fore opening the vacuum inlet door. Theengine must be stopped and the impel-ler blades no longer turning to avoid se-rious injury from the rotating blades.• Inspect unit before each use for
worn, loose, missing, or damagedparts. Do not use until unit is inproper working order.
• Keep outside surfaces free from oiland fuel.
• Never start or run engine inside aclosed room, building or other un-ventilated area. Breathing exhaustfumes can kill.
• To avoid static electricity shock, donot wear rubber gloves or any otherinsulated gloves while operating unit.
• Do not set unit on any surface ex-cept a clean, hard area while engineis running. Debris such as gravel,sand, dust, grass, etc. could bepicked up by the air intake and
thrown out through discharge open-ing, damaging unit, property, or caus-ing serious injury to bystanders oroperator.
• Avoid dangerous environments. Donot use in unventilated areas orwhere explosive vapors or carbonmonoxide build up could be present.
• Do not overreach or use from unsta-ble surfaces such as ladders, trees,steep slopes, rooftops, etc. Keep firmfooting and balance at all times.
• Never place objects inside the blowertubes; always direct the blowing debrisaway from people, animals, glass, andsolid objects such as trees, automo-biles, walls, etc. The force of air cancause rocks, dirt, or sticks to bethrown or to ricochet which can hurtpeople or animals, break glass, orcause other damage.
• Never run unit without the properequipment attached. When usingyour unit as a blower, always installblower tubes. When using the op-tional vacuum kit, always install vac-uum tubes and vacuum bag assem-bly. Make sure vacuum bag assem-bly is completely zipped.
• Check air intake opening, blowertubes, and vacuum tubes frequently,always with engine stopped andspark plug disconnected. Keep ventsand discharge tubes free of debriswhich can accumulate and restrictproper air flow.
• Never place any object in air intakeopening as this could restrict proper airflow and cause damage to the unit.
• Never use for spreading chemicals,fertilizers, or other substances whichmay contain toxic materials.
• To avoid spreading fire, do not usenear leaf or brush fires, fireplaces,barbecue pits, ashtrays, etc.
• Use only for jobs explained in thismanual.
MAINTAIN YOUR UNIT PROPERLY• Have all maintenance other than the
recommended procedures describedin the instruction manual performedby a Sears Service Center.
• Disconnect spark plug before per-forming maintenance except for car-buretor adjustments.
• Use only recommended Craftsman ®replacement parts; use of any otherparts may void your warranty andcause damage to your unit.
-3-
• Empty fuel tank before storing the unit.Use up fuel left in carburetor by start-ing engine and letting it run until itstops.
• Do not use any accessory or attach-ment other than those recommendedby manufacturer for use with your unit.
• Do not store the unit or fuel in aclosed area where fuel vapors canreach sparks or an open flame fromhot water heaters, electric motors orswitches, furnaces, etc.
• Store in a dry area out of reach ofchildren.
SAFETY NOTICE: Exposure to vibra-tions through prolonged use of gasolinepowered hand tools could cause bloodvessel or nerve damage in the fingers,hands, and joints of people prone to cir-culation disorders or abnormal swelling.Prolonged use in cold weather has beenlinked to blood vessel damage in other-wise healthy people. If symptoms occursuch as numbness, pain, loss ofstrength, change in skin color or texture,or loss of feeling in the fingers, hands, orjoints, discontinue the use of this tooland seek medical attention. Anantivibratioo system does not guaranteethe avoidance of these problems. Users
who operate power tools on a continualand regular basis must monitor closelytheir physical condition and the conditionof this tool.
SPECIAL NOTICE: For users on U.S.Forest Land and in some states, includ-ing California (Public Resources Codes4442 and 4443), idaho, Maine, Minne-sota, New Jersey, Oregon, and Wash-ington: Certain internal combustion en-gines operated on forest, brush, and/orgrass covered land in the above areasare required to be equipped with a sparkarresting screen, maintained in effectiveworking order, or the engine must beconstructed, equipped, and maintainedfor the prevention of fire. Check withyour state or local authorities for regula-tions pertaining to these requirements.Failure to follow these requirements is aviolation of the law. This unit is not facto-ry equipped with a spark arrestingscreen; however, a spark arrestingscreen is available as an optional part. Ifa spark arresting screen is required inyour area, contact Sears Service for thecorrect kit. The spark arresting screen,blower tubes, and nozzles must be as-sembled to unit to be in full compliancewith regulations.
CARTON CONTENTSCheck carton contents against the fol-lowing list.Model 358.797342
BlowerBlower tubeElbow tubeVacuum bagUpper vacuum tubeLower vacuum tube2-Cycle Engine Oil
NOTE: It is normal for the fuel filter torattle in the empty fuel tank.
ASSEMBLY
_WARNING: Stop engine and besure the impeller blades have stoppedturning before opening the vacuum in-let door or attempting to insert or re-move the vacuum tubes. The rotatingblades can cause serious injury.
_WARNING: If you receive yourunit assembled, repeat all steps to en-sure your unit is properly assembledand all fasteners are secure.
• Astandard screwdriver is requiredfor assembly.
BLOWER ASSEMBLYBLOWER TUBE ASSEMBLYIf you have already assembled yourunit for use as a vacuum, remove thevacuum tubes and collection bag.1. Align the rib on the blower tube
with the groove in the blower outlet;slide the tube into place.
NOTE: Knob must be loose enough toallow blower tube to be inserted in blow-er outlet. Loosen knob by turning coun-terclockwise.
_luOtl_tr Blower
Groove_ _ Rib
2. Secure the tube by turning theknob clockwise.
3. To remove the tube, turn the knobcounterclockwise to loosen thetube; remove the tube.
-4-
VACUUM ASSEMBLYVACUUM BAG ASSEMBLY1, Open the zipper on the vacuum
bag and insert the elbow tube.2, Push the small end of the elbow
tube through the small opening inthe bag,
ElbowTube Small
Opening
ZippeOpening Rib
NOTE: Make sure edge of the smallopening is flush against the flared areaof the elbow tube, and the rib on theelbow tube is on the bottom.
3, Close the zipper on the bag, Makesure the zipper is closed completely.
4, Remove blower tube from engine.
Rib
Latch _ BlowerAreha_l TI_ Outlet
" @= Inlet Cover
3, Gently tilt the handle of the screw-driver toward the back of the unit torelease the latch while pulling upon the vacuum inlet cover with yourother hand.
4, Hold the vacuum inlet cover openuntil upper vacuum tube is installed,
RetaininV_CpUoUs_]_
5, Place the hooks of the upper vacu-um tube on the retaining posts ofthe unit.
6, Pivot the tube until it is secured tothe blower unit by the vacuum inletlatch.
5, Insert the elbow tube into the blow-er outlet, Make sure elbow tube isaligned with the blower outletgroove,
6, Turn knob clockwise to secure el-bow tube,
VACUUM TUBE ASSEMBLY1, Align the lower vacuum tube as
shown. Push lower vacuum tubeinto upper vacuum tube,UpperVacuum Tube_--=.
LowerVacuum Tube
2, Insert the tip of a screwdriver intothe latch area of the vacuum inlet,
PIVOTInlet Cover
Latch
RetainingPost
HOW TO CONVERT UNIT FROMVACUUM USE TO BLOWER USE1, Remove the vacuum tubes by in-
serting the tip of a screwdriver intothe latch area of the vacuum inlet,
2, Gently tilt handle of screwdriver to-ward the back of the unit to releasethe latch while pulling up on the up-per vacuum tube with your otherhand,
-5-
3. Remove the vacuum bag.4. Close the vacuum inlet cover and
make sure it is latched closed.5. Reinstall the blower tube (see
BLOWER TUBE ASSEMBLY).SHOULDER STRAP ADJUSTMENT(for vacuum use only)1. Hold the unit as shown with the
muffler side facing away from yourbody and clothes.
2. Pass the shoulder strap over yourhead and onto your right shoulder.
3, Extend your left arm toward therear of the vacuum bag.
4. Adjust shoulder strap until the vac-uum bag/shoulder strap seam liesbetween your thumb and indexfinger.
5. Make sure air flows freely from theelbow tube into bag. If bag is kinked,the unit will not operate properly.
KNOW YOUR BLOWERREADTHIS INSTRUCTIONMANUALAND SAFETY RULES BEFOREOPERATINGYOURUNIT. Compare the illustrationswith your unit to familiarize yourself with the locationof the various controls and adjustments. Save this manual for future reference.MULCHING BLADESYour bower is equipped with mulching blades as a standard feature. When usingthe optional vacuum attachment, the mulching blades automatically reduce debrisat a ratio of up to 16:1.
Upper
Lower Vacuum Tu(__Vacuum Tube
Throttle
Primer ButtonChoke Lever
Fuel Mix
Elbow Tube
BlowerTube
\
StarterRope
RearHandle
-6-
THROTTLE LEVERThe THROTTLE LEVER is used to selectthe desired engine speed and to stopthe engine. Move the throttle lever tothe _ position for full speed opera-tion. Move the throttle lever to the
position for idle speed. To stopthe engine, move the throttle lever tothe STOP position.
PRIMER BUTTONThe PRIMER BUTTONremoves air fromthe carburetor and fuel lines and fillsthem with fuel. This allows you to start
the engine with fewer pulls on the starterrope. Activate primer button by pressingit and allowing it to return to its originalposition.
CHOKE LEVERThe CHOKE helps to supply fuel to theengine to aid in cold starting. Activatethe choke by moving the choke lever tothe FULL CHOKE position. After engineattempts to start, move the choke leverto the HALF CHOKE position. Once en-gine starts, move choke lever to theRUN position.
OPERATING TIPS• While vacuuming or blowing debris,
hold the unit with the muffler side fac-ing away from your body and clothes(see OPERATING POSITION below).
• To reduce the risk of hearing lossassociated with sound level(s), hear-ing protection is required.
• To reduce the risk of injury associatedwith contacting rotating parts, stop theengine before installing or removingattachments. Do not operate withoutguard(s) in place.
• Operate power equipment only at rea-sonable hours-not early in the morn-ing or late at night when people mightbe disturbed. Comply with times listedin local ordinances. Usual recommen-dations are 9:00 a.m. to 5:00 p.m..Monday though Saturday.
• To reduce noise levels, limit the num-ber of pieces of equipment used atany one time.
• To reduce noise levels, operate pow-er blowers at the lowest possiblethrottle speed to do the job.
• Use rakes and brooms to loosendebris before blowing.
• In dusty conditions, slightly dampensurfaces or use a mister attachmentwhen water is available.
• Conserve water by using power blow-ers instead of hoses for many lawnand garden applications, includingareas such as gutters, screens, patios.grills, porches, and gardens.
• Watch out for children, pets, openwindows, or freshly washed cars.Blow debris away safely.
• Use the full blower nozzle extensionso the air stream can work close tothe ground.
• After using blowers and other equip-ment, CLEAN UP! Dispose of debrisin trash receptacles.
OPERATING POSITION
Blower Vacuum
BEFORE STARTING ENGINE
_WARNING: Be sure to read the
fuel information in the safety rulesbefore you begin, If you do notunderstand the safety rules, do notattempt to fuel your unit. Call1-800-235-5878.FUELING ENGINE
_WARNING: Remove fuel capslowly when refueling.This engine is certified to operate on un-leaded gasoline. Before operation, gaso-line must be mixed with a good qualitysynthetic 2-cycle air-cooled engine oil.We recommend Craftsman brand syn-thetic oil. Mix gasoline and oil at a ratioof 40:1. A 40:1 ratio is obtained by mix-ing 3.2 ounces of oil with 1 gallon of un-leaded gasoline. Included with thisblower is a 3.2 ounce container of oil.Pour the entire contents of this containerinto 1 gallon of gasoline to achieve theproper fuel mixture. DO NOT USE auto-motive oil or boat oil. These oils willcause engine damage. When mixingfuel, follow instructions printed on con-tainer. Once oil is added to gasoline,shake container momentarily to assurethat the fuel is thoroughly mixed. Alwaysread and follow the safety rules relatingto fuel before fueling your unit.
-7-
IMPORTANTExperience indicates that alcoholblended fuels (called gasohol or usingethanol or methanol) can attract mois-ture which leads to separation andformation of acids during storage.Acidic gas can damage the fuel sys-tem of an engine while in storage.To avoid engine problems, empty thefuel system before storage for 30 daysor longer. Drain the gas tank, start theengine and let it run until the fuel linesand carburetor are empty. Use freshfuel next season.Never use engine or carburetor clean-er products in the fuel tank or perma-nent damage may occur.Fuel stabilizer is an acceptable alter-native in minimizing the formation offuel gum deposits during storage.Craftsman brand oil is already blendedwith fuel stabilizer. See the STORAGEsection for additional information.
NOTE: Unit must be placed on its sidewhen adding fuel (see illustration below).
STARTING POSITION
Blower _/_
Vacuum
WARNING: When starting engine,hold the unit as illustrated. Do not setunit on any surface except a clean, hardarea when starting engine or while en-gine is running. Debris such as gravel,sand, dust, grass, etc. could be pickedup by the air intake and thrown outthrough the discharge opening, damag-ing the unit or property, or causing seri-ous injury to bystanders or the operator.STARTING A COLD ENGINE (or awarm engine after running out offuel)1. Slowly press the primer button 8
times.2. Move the choke lever to the FULL
CHOKE position.3. Move the throttle lever to the
position.Throttle Lever Primer Button
STOPPING YOUR ENGINE• To stop the engine, move the throttle
lever to the STOP position.
STARTING THE ENGINE
_WARNING: You MUST make sure
the tubes are secure before using theunit.• Fuel engine. Move at least 10 feet (3
meters) away from the fueling site.• Hold the unit in the starting position
as shown. Make sure the blower endis directed away from people, ani-mals, glass, and solid objects.
Choke Lever
4. Pull starter handle sharply until theengine attempts to run, but nomore than 5 pulls (below 30°F, 8pulls).
NOTE: If the engine attempts to startbefore the 5th pull, go to the next stepimmediately.5. Move choke lever to HALF CHOKE.6. Pull the starter handle sharply until
the engine runs, but no more than5 pulls (below 30°F, 10 pulls).
7. After a 5 second warm-up, movethe choke lever to the RUN posi-tion.
-8-
8. Allow the unit to run for 30 moreseconds at RUN before moving thethrottle lever to the "_P position.
If the engine has not started after 5pulls (at HALF CHOKE), repeat theSTARTING A COLD ENGINE procedure.If the engine still does not start, pro-ceed to STARTING A FLOODED ENGINE.9. To stop the engine, move the
throttle lever to the STOP position.STARTING A WARM ENGINE1. Move the throttle lever to the
position.2. Pull the starter handle sharply until
the engine starts, but no more than5 pulls.
NOTE: If the engine has not started,pull starter handle sharply for 5 morepulls. If engine still does not run, it isprobably flooded. Proceed to START-ING A FLOODED ENGINE.
3. To stop the engine, move thethrottle lever to the STOP position.
STARTING A FLOODED ENGINEFlooded engines can be started by plac-ing the choke lever in the RUN position.Move throttle lever to the fast position
; then, pull rope until engine starts.After engine starts, move the throttle le-ver to the slow position "_P to allow en-gine to idle.Starting could require pulling the starterrope many times depending on howbadly the unit is flooded. If the unit stilldoesn't start, refer to theTROUBLESHOOTINGTABLE or call1-800-235-5878.
CUSTOMER RESPONSIBILITIES
WARNING: Disconnect the spark plugservice, or adiustments.
CARE & MAINTENANCE TASK
Check for loose fasteners and partsCheck for damaged or worn parts
Inspect and clean unit and labelsClean air filter
Replace spark plugReplace fuel filter
Check muffler mounting screws
before performing maintenance,
WHEN TO PERFORMBefore each use
Before each useAfter each use
Every 5 hours of operation
Yearly
YearlyYearly
_WARNING: Avoid touching muf-fler unless engine and muffler are cold.A hot muffler can cause serious burns.
_WARNING: Stop engine and besure the impeller blades have stoppedturning before opening the vacuum in-let door or attempting to insert or re-move the vacuum or blower tubes.The rotating blades can cause seriousinjury. Always disconnect the sparkplug before performing maintenance oraccessing movable parts.
GENERAL RECOMMENDATIONSThe warranty on this unit does not cov-er items that have been subjected tooperator abuse or negligence, To re-ceive full value from the warranty, theoperator must maintain unit as instruct-ed in this manual, Various adjustments
will need to be made periodically toproperly maintain your unit.
CHECK FOR LOOSEFASTENERS AND PARTS, Spark Plug Boot* Air Filter* Housing ScrewsCHECK FOR DAMAGED ORWORN PARTSContact Sears Service Center for re-placement of damaged or worn parts.* Throttle Lever - Ensure throttle lever
functions properly by moving thethrottle lever to the STOP position.Make sure engine stops; then restartengine and continue.
* Fuel Tank - Do not use unit if fuel tankshows signs of damage or leaks.
* Vacuum Bag - Do not use vacuumbag if it is torn or damaged.
-9-
INSPECT AND CLEAN UNITAND LABELS, After each use, inspect complete unit
for loose or damaged parts. Cleanthe unit using a damp cloth with amild detergent.
* Wipe off unit with a clean dry cloth.CLEAN AIR FILTER
'rve 'te
_ / Screws/ ._lrFilter
A dirty air filter decreases engine per-formance and increases fuel consump-tion and harmful emissions. Alwaysclean after every 5 hours of operation.Cleaning the air filter:1, Clean the cover and the area
around it to keep debris from fallinginto the carburetor chamber whenthe cover is removed,
2. Remove parts as illustrated.NOTE: Do not clean filter in gasolineor other flammable solvent. Doing socan create a fire hazard or produceharmful evaporative emissions.3. Wash the filter in soap and water.4. Allow filter to dry.5. Apply a few drops of oil to the filter;
squeeze filter to distribute oil.6. Replace parts.REPLACE SPARK PLUGReplace spark plug each year to ensurethe engine starts easier and runs better.Set spark plug gap at 0.025 inch. Igni-tion timing is fixed, nonadjustable.1. Twist, then pull off spark plug boot.2. Remove spark plug from cylinder
and discard.3. Replace with Champion CJ-6Y
spark plug and tighten securelywith a 3/4 inch socket wrench.
4. Reinstall the spark plug boot.
REPLACE FUEL FILTERTo replace fuel filter, drain unit by run-ning it dry of fuel, then remove fuelcap/retainer assembly from tank. Pullfilter from tank and remove it from thefuel line. Install new fuel filter on fuelline; reinstall parts.
_,
uelLine
.... Fuel Filter
CHECK MUFFLER MOUNTINGSCREWSOnce each year, ensure mufflermounting screws are secure and tight-ened properly to prevent damage.
Mounting
Muffler Cover _Sc_ew
1, Loosen and remove the 2 screwsfrom the muffler cover.
2, Remove the muffler cover,3, Tighten the 2 muffler mounting
screws securely,4, Reinstall muffler cover and 2
screws. Tighten securely,CARBURETOR ADJUSTMENTThere is no screw for idle adjustmenton your blower, The throttle lever isused to control engine speed, Thethrottle lever can be placed in one offour positions: STOP, IDLE or _,FULL THROTTLE or _. and one inter-mittent position. If your engine willnot run properly or you require furtherassistance, contact your Sears ServiceCenter or call our customer assistancehelp line at 1-800-235-5878.
-10-
411.WARNING: Perform the followingsteps after each use:• Allow engine to cool, and secure the
unit before storing or transporting.• Store unit and fuel in a well venti-
lated area where fuel vapors cannotreach sparks or open flames fromwater heaters, electric motors orswitches, furnaces, etc.
• Store unit with all guards in place.Position unit so that any sharp objectcannot accidentally cause injury.
• Store unit and fuel well out of thereach of children.
SEASONAL STORAGE
Prepare unit for storage at end of sea-son or if it will not be used for 30 daysor more.If your unit is to be stored for a periodof time:• Clean the entire unit before lengthy
storage.• Store in a clean dry area.• Lightly oil external metal surfaces.
FUEL SYSTEMUnder FUELING ENGINE in the OPERA-TiON section of this manual, see mes-sage labeled IMPORTANT regarding theuse of gasohol in your engine.
Fuel stabilizer is an acceptable alterna-tive in minimizing the formation of fuelgum deposits during storage. Add stabi-lizer to gasoline in fuel tank or fuel stor-age container. Follow the mix instruc-tions found on stabilizer container. Runengine at least 5 minutes after addingstabilizer. Craftsman 40:1, 2-cycle en-gine oil (air cooled) is already blendedwith fuel stabilizer. If you do not usethis Sears oil, you can add a fuel stabi-lizer to your fuel tank.ENGINE• Remove spark plug and pour 1 tea-
spoon of 40:1, 2-cycle engine oil (aircooled) through the spark plug open-ing. Slowly pull the starter rope 8 to10 times to distribute oil.
• Replace spark plug with new one ofrecommended type and heat range.
• Clean air filter.• Check entire unit for loose screws,
nuts, and bolts. Replace any dam-aged, broken, or worn parts.
• At the beginning of the next season,use only fresh fuel having the propergasoline to oil ratio,
OTHER• Do not store gasoline from one sea-
son to another,• Replace your gasoline can if it starts
to rust,
-11 -
TROUBLESHOOTING TABLEWARNING: Always stop unit and disconnect spark plug before perform-ing any of the recommended remedies below other than remedies that re-quire operation of the unit,
TROUBLE CAUSE REMEDY
Engine will not 1. Engine flooded. 1. See "Starting a Flooded Engine"start, in Operation section.
2. Fuel tank empty. 2. Fill tank with correct fuel mixture.3. Spark plug not firing. 3. Install new spark plug.4. Fuel not reaching 4. Check for dirty fuel filter; replace.
carburetor. Check for kinked or split fuel line;repair or replace.
5. Compression low. 5. Contact Sears Service (see back cover).
Engine will not 1. Fuel not reaching 1. Check for dirty fuel filter; replace.idle properly, carburetor. Check for kinked or split fuel line;
repair or replace.2. Carburetor requires 2. Contact Sears Service (see back cover).
adjustment.3. Crankshaft seals worn.
4. Compression low.
1. Air filter dirty.2. Fuel not reaching
carburetor.
Engine will notaccelerate,lacks power, ordies under aload.
Engine smokesexcessively.
Engine runs hot.
3. Spark plug fouled.
4. Carburetor requiresadjustment.
5. Carbon build up.6. Compression low.1. Choke partially on.2. Fuel mixture incorrect.
3. Air filter dirty.4. Carburetor requires
adjustment.1. Fuel mixture incorrect.
2. Spark plug incorrect.3. Carburetor requires
adjustment.4. Carbon build up.
YOUR WARRANTY RIGHTS AND
3. Contact Sears Service (see back cover).4. Contact Sears Service (see back cove0.
1. Clean or replace air filter.2. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;repair or replace.
3. Clean or replace spark plugand re-gap.
4. Contact Sears Service (see back cover).
5. Contact Sears Service (see back cover).6. Contact Sears Service (see back cover).
1. Adjust choke.2. Empty fuel tank and refill with
correct fuel mixture.3. Clean or replace air filter.4. Contact Sears Service (see back cover).
1. See "Fueling Engine" in Operationsection.
2. Replace with correct spark plug.3. Contact Sears Service (see back cover).
4. Contact Sears Service (see back cover).
OBLIGATIONS: The U. S. Environ-mental Protection Agency and Sears,Roebuck and Co., U.S.A., are pleasedto explain the emissions control sys-tem warranty on your year 2002-2004small off-road engine. Sears mustwarrant the emission control systemon your small off-road engine for theperiods of time listed below providedthere has been no abuse, neglect, orimproper maintenance of your smalloff-road engine. Your emission controlsystem includes parts such as the car-
buretor and the ignition system. Wherea warrantable condition exists, Searswill repair your small off-road engineat no cost to you. Expenses coveredunder warranty include diagnosis,parts and labor. MANUFACTURER'SWARRANTY COVERAGE: If anyemissions related part on your engine(as listed under Emissions ControlWarranty Parts List) is defective or adefect in the materials or workmanshipof the engine causes the failure ofsuch an emission related part, the partwill be repaired or replaced by Sears.
-12-
OWNER'S WARRANTY RESPONSI-BILITIES: AS the small off-road en-gine owner, you are responsible for theperformance of the required mainte-nance listed in your instruction manual.Sears recommends that you retain allreceipts covering maintenance on yoursmall off-road engine, but Sears can-not deny warranty solely for the lack ofreceipts or for your failure to ensurethe performance of all scheduled main-tenance. As the small off-road engineowner, you should be aware thatSears may deny you warranty cover-age if your small off-road engine or apart of it has failed due to abuse, ne-glect, improper maintenance, unap-proved modifications, or the use ofparts not made or approved by theoriginal equipment manufacturer. Youare responsible for presenting yoursmall off-road engine to a Sears au-thorized repair center as soon as aproblem exists. Warranty repairsshould be completed in a reasonableamount of time, not to exceed 30 days.If you have any questions regardingyour warranty rights and responsibili-ties, you should contact your nearestauthorized service center or call Searsat 1-800-469-4663. WARRANTYCOMMENCEMENT DATE: The war-ranty period begins on the date thesmall off-road engine is purchased.LENGTH OF COVERAGE: This war-ranty shall be for a period of two yearsfrom the initial date of purchase.WHAT IS COVERED: REPAIR ORREPLACEMENT OF PARTS. Repairor replacement of any warranted partwill be performed at no charge to theowner at an approved Sears servicingcenter. If you have any questions re-garding your warranty rights and re-sponsibilities, you should contact yournearest authorized service center orcall Sears at 1-800-469-4663. WAR-RANTY PERIOD: Any warranted partwhich is not scheduled for replace-ment as required maintenance, orwhich is scheduled only for regular in-spection to the effect of "repair or re-
place as necessary" shall be war-ranted for 2 years. Any warranted partwhich is scheduled for replacement asrequired maintenance shall be war-ranted for the period of time up to thefirst scheduled replacement point forthat part. DIAGNOSIS: The ownershall not be charged for diagnostic la-bor which leads to the determinationthat a warranted part is defective if thediagnostic work is performed at an ap-proved Sears servicing center. CON-SEQUENTIAL DAMAGES: Sears maybe liable for damages to other enginecomponents caused by the failure of awarranted part still under warranty.WHAT IS NOT COVERED: All failurescaused by abuse, neglect, or impropermaintenance are not covered. ADD-ON OR MODIFIED PARTS: The useof add-on or modified parts can begrounds for disallowing a warrantyclaim. Sears is not liable to cover fail-ures of warranted parts caused by theuse of add-on or modified parts.HOW TO FILE A CLAIM: If you haveany questions regarding your warrantyrights and responsibilities, you shouldcontact your nearest authorized ser-vice center or call Sears at1-800-469-4663. WHERE TO GETWARRANTY SERVICE: Warranty ser-vices or repairs shall be provided at allSears service centers. Call1-800-469-4663. MAINTENANCE,REPLACEMENT AND REPAIR OFEMISSION RELATED PARTS: AnySears approved replacement partused in the performance of any war-ranty maintenance or repair on emis-sion related parts will be provided with-out charge to the owner if the part isunder warranty. EMISSION CON-TROL WARRANTY PARTS LIST: Car-buretor, Ignition System: Spark Plug(covered up to maintenance sched-ule), Ignition Module. MAINTENANCESTATEMENT: The owner is responsi-ble for the performance of all requiredmaintenance as defined in the instruc-tion manual.
This engine is certified to be emissions compliant for the following use:
[] Moderate (50 hours)
[] Intermediate (125 hours)
[] Extended (300 hours)
-13-
Declaraci6n de Garantia 17 AImacenaje 28Reglas de Seguridad 17 Tabla Diagn6stica 29Montaje 20 Declaraci6n de Emision 30Uso 22 Lista de Piezas 14Mantenimiento 26 Repuestos y Encargos Contratapa
GARANTIA DE DOS A_IOS COMPLETOS PARA EL PROPULSOR DE AIRE AGASOLINA DE LA MARCA CRAFTSMAN ®Durante dos (2) a_os a partir de la fecha de compra, siempre que se haga elmantenimiento, la lubricaci6n y los ajustes en este Propulsor de Aire a Gasolinaseg_n las instrucciones de uso y mantenimiento en el manual de instrucciones,Sears reparar_ cualquier defecto de material o mano de obra granturaitamente.Esta garantia excluye los tubos del propulsor de aire, la bujia y el filtro de aire,que son piezas prescindibles que se pueden gastar con el uso normal.Si este propulsor de aire es usado con fines de uso comercial, esta garantia aplicar_solamente por 90 dias despu6s de la fecha original de compra. Siesta propulsor esusado con fines de alquiler, esta garantia aplicar_ por solo 30 dias despu6s de lafecha original de compra. Esta garantia tiene validez exclusivamente cuando el apa-rato es utilizado dentro de los Estados Unidos.SE OBTEDRA SERVICIO BAJO GARANTIA DEVOLVIENDO EL APARATO AL TIENDA DESEARS O CENTRO DE SERVICIO MAS CERCANO EN LOS ESTADOS UNIDOS.Esta garantia confiere derechos legales especificos al propietario, que tal veztenga asimismo otros derechos que varian entre estados.Sears, Roebuck and Co., D/817WA, Hoffman Estates, IL 60179
ADVERTENCIA: De no cumplircon todas las Reglas y Precaucionesde Seguridad, correr_ el riesgo de ac-cidentes muy graves.
CONOZCA SU APARATO• Lea el manual de instrucciones cui-
dadosamente hasta que comprendaperfectamente todas las adverten-cias e instrucciones de seguridad ylas pueda cumplir, antes de porter elaparato en funcionamiento.
• Limite el uso del aparato a aquellaspersonas que comprendan todas lasadvertencias e instrucciones de se-guridad en este manual y vayan acumplir con elias.
ADVERTENClA: Inspeccione el_rea antes de poner en matodos los es-combros y objetos s61idos tales comopiedras, vidrio, alambre, etc., que el apa-rato pueda arrojar al aire o hacer rebotarcausando heridas de este o cualquierotro modo durante el uso del mismo.
Utilice su aparato como propulsor deaire para:• Barrer escombros o recortes de
hierba de caminos de entrada,aceras, patios, etc.
• Soplar recortes de hierba, para uhojas en montones, o para removerescombros de esquinas, alrededorde uniones o entre ladrillos.
Utilice su aparato como aspiradora para:• Recoger material seco como hojas,
hierba, ramas peque5as y pedazospequeBos de papeL
• Para obtener mejores resultados alusar la aspiradora, ponga el motor aalta velocidad.
• Mu6vase lentamente de un lado aotro sobre el material que de seaaspirar. Evite el forzar el aparato arecoger montones de desechospues esto podria obstruir el aparato.
• Para obtener mejores resultados,mantenga el tubo de aspiraci6n unos3 cm (uno pulgada) m_s arriba delsuelo.
-17-
PIENSE ANTES DE PROCEDER• Use siempre protecci6n para los ojos
al hacer uso, servicio o mantenimkento del aparato. El uso de proteci6nde ojos ayudar_ a prevenir la p6rdi-da de la vista y/u otras heridasgraves, provocadas por piedras oescombros que reboten en los ojos yen la cara al ser propulsados por elaparato. La protecci6n para los ojosdebe ser marcada Z87.
• Use siempre protecoi6n en los pies.No use el aparato descalzo ni consandalias.
• Use siempre mascarilla de filtraci6no de protecci6n para la cara al traba-jar en ambientes polvorientos.
• Mantenga el cabello por encima delos hombros, at_ndolo para tal efectosi es necesario. No use joyas, ropasuelta, ni ropa con tiras, corbatas,borlas, etc. que cuelgen libremente,porque podrian quedar enredadasen las piezas en movimiento delaparato.
• No use el aparato estando cansado.enfermo, ansioso, ni bajo la infuen-cia del alcohol, las drogas u otrosmedicamentos.
• Mantenga a niSos, espectadores yanimales a una distancia minima de10 metros (30 pies) al poner en mar-cha o al usar el aparato. No seSalela boquilla en la direcci6n de la per-sonas o de animales dom6sticos.
MANEJE EL COMBUSTIBLE CONEXTREMO CU|DADO, ES ALTA-MENTE INFLAMABLE• Elimine todas las posibles fuentes de
chispan o llamas (inclusive los cigar-rillos, las llamas abertas, y cualquiertrabajo que cause chispas) en las_reas donde se mezcla, vierte o al-macena el combustible.
• Mezcle y vierta el combustible al aire]ibre, almacene el combustible en un]ugar fresco, seco y bien ventilado;sue un recipiente aprobado paracombustible y marcado para todomanejo de combustible.
• No fume mientras trabaja con elcombustible ni cuando est6 hacien-do uso del aparato.
• AsegQrese que el aparato est6 cor-rectamente armado yen buena con-dici6n de funcionamiento.
• No Ilene el tanque de combustiblemientras el motor se encuentre enmamha,
• Evite derramar el combustible o elaceite. Limpie todos los derramesde combustible antes de porter elaparato en marcha.
• AI6jese por Io menos 3 metros (10pies) del combustible y del lugar deabastecimineto antes de poner elmotor en marcha.
• AImac6ne siempre combustible enun recipiente aprobado para los liqui-dos inflamables.
HAGA USO SEGURO DE SUAPARATO
ADVERTENClA: Detenga elmotor antes de abrir ]a compuerta deentrada de aire del aspirador. El motordeber_ encontrarse detenido y las cu-chillas del impulsor no deber_n estargirando para evitar serios accidentesprovocados por las cuchillas girantes.• Verifique por inspecci6n, antes de
cada uso, que no haya piezas gasta-das, sueltas, ni daSadas o piezasque falten. No use el aparato hastaque este se encuentre en perfectascondiciones de funcionamiento.
• Mantenga las superficies externaslibres de aceite y de combustible.
• Nunca ponga el motor en marcha ni1odeje en marcha dentro de un re-cintocerrado o en una _rea sin venti-]aci6n. Respirar los vapores del com-bustible le podria causar la muerte.
• Para evitar el choque por electrici-dad est_tica, no use guantes degoma ni ningDn otro guante aisladoal usar el aparato.
• No apoye el aparato con el motor enmarcha en ninguna superficie queno est6 limpia o que no sea s61ida.El aparato podria aspirar escombrostales como gavilla, arena, polvo.c6sped, etc. por la entrada de aspi-raci6n y arrojarlos por la salida depropulsion, daSando el aparato y/uotros objetos, o causando gravesheridas a espectadores o al usuario.
• Evite ambientes peligrosos, No useel aparato en lugares sin ventilaci6nni donde puda haber vapores explo-sivos o mon6xido de carbono.
• No se extienda excesivamente niuse el aparato en superficies inest-ables tales como escaleras, _rboles.declives acentuadas, techos, etc.Mantenga el equilibrio, con los piesen una superficie estable en todomomento.
-18-
• Nunca coloque objetos dentro de lostubes de propulsi6n; siempre dirijalos escombros en direcci6n contrariaa donde personas, animales, vidrier-aso otros objetos s61idos tales como_rboles, autom6viles, paredes, etc.se encuentran. La fuerza del airepuede arrojar o hacer rebotar pie-dras, tierra o ramas, hiriendo a per-sonas o animales, rompiendo vidrier-as o causando otros daSos.
• Nunca ponga el aparato en marchasin toner todo el equipo correspon-diente instalado. AI usar el aparatocome propulsor de aire, sirmpreinstale los tubos de propulsi6n. AIusar el equipo opcional de aspira-ci6n, siempre instale los tubes y labolsa de aspiraci6n. Aseg_rese que]a cremallera de la bolsa de aspira-ci6n se encuentre completamentecerrada.
• Inspeccione frecuentemente la aber-tura de entrada de aire, los tubos depropulsion, los tubos de aspiraci6n yel tubo en forma de codo siemprecon el motor detenido y la bujfa des-conectada. Mantenga las aberturasde ventilaci6n y los tubos de descar-ga libres de escombros que se pue-den acumular y limitar la circulaci6ndebida de aire.
• Nunca coloque objeto alguno dentrode la entrada de aire ya que de hac-erlo podria limitar la circulaci6n d'airey daSar el aparato.
• Nunca use el aparato para esparcirsubstancias quimicas, fertilizantes uotras substancias que puedan con-tener materiales t6xicos.
• Para evitar la propagaci6n de incen-dios, no use el aparato cerca de ho-gueras de hogassecas o de mator-rales, de hogares de leSa, de parril-las, barbacoas, ceniceros, etc.
• Use el aparato exclusivamente paralos fines descritos en este manual.
HAGA EL MANTENIMIENTO DELAPARATO EN LA FORMA DEBIDA• Permita que todo mantenimiento
aparte de los procedimientos recom-endados descritos en este manualde instrucciones, sean efectuadospor un Centro de Servicio Sears.
• Desconecte la bujfa antes de hacercualquier mantenimiento, con la ex-cepci6n de los ajustes al carburador.
• Use exclusivamente los repuestosrecomendados de la marcaCraftsman®; el use de cualquier otro
repuesto podr_ invalidar la garantiao daSar el aparato.
• Vacia el tanque de combustibleantes de almacenar el aparato. Con-suma el combustible restante en elcarburador poniendo el motor enmarcha y dej_ndolo en marhca has-ta que se 6ste se detenga.
• No use ning_n accesorio ni piezaadicional aparte de los recomenda-dos por el fabricante para usar consu aparato.
• No almacene el aparato ni el com-bustible en un recinto cerrado dondelos vapores el combustible puedanentrar en contacto con chispas o lla-mas abiertas procedentes de calen-tadores de agua, motores o interrup-tores el6ctricos, calefactores cen-trales, etc.
• AImacene el aparato en un lugarseco. fuera del alcance de los niSos.
AVISO DE SEGURIDAD: El estar ex-puesto alas vibraciones a trav6s deluso prelongado de herramientas defuerza a gasolina, puede causar daSosa los vases sangufneos o a los nerviosde los dedos, las manos y las coyuntu-ras a aqueUas personal propensas a lostrastornos de la circulaci6n o alas hin-chazones anormales. El use prolongadoen climas fries ha side asociado condaSos a los vases sanguineos a perso-nas que por otra parte se encuentran enperfecto estado de salud. Si ccurrierasfntemas tales como el entumecimiento,el color, la falta de sentido en los dedos,las manes o en las coyunturas, pare deusar esta m_quina de inmediato y pro-cure atenci6n m6dica. Los sistemas deanti-vibraci6n no garantizan que se evi-tan tales problemas. Los usuarios quehacen use continuo y prolongado de lasherramientas de fuerza deben fiscalizaratnetamente su estado fisico y el esta-do del aparato.
AVISO ESPECIAL: Para los usuariosen Tierras Forestadas en los EstadosUnidos y en algunos estados, incluyen-de California (C6digos de RecursosP6blicos 4442 y 4443). Idaho, Maine,Minnesota, Nueva Jersey, Oreg6n yWashington: Se requiere a ciertos mo-tores de combusti6n interna operadosen tierras cubiertas por bosques, mator-rales y/o pasto, en las _rea anterior-mente mencionadas, que vengan equi-pados con rejilla anti-chispas, manten-ida en perfecto estado de funcionamien-to, o que el motor est6 construido yequipado para la prevenci6n de incen-
-19-
dies y mantenido correctamente. Con-suite con las autoridades estatales o lo-cales acerca de los reglamente que serelacionene con estos requisitos. De nocumplir con estos requisitos, usted es-tar_ en violaci6n de la ley. Este aparatono viene equipo de f_brica con rejillaanti-chispa; sin embargo la rejina anti-chispa viene disponible como pieza op-
cional. Si se requiere rejilla anti-chispaen la Iocalidad donde usted se encuen-tra, entre en contacto con el Servicio deSears para obtener el equipo de re-puestos correspondiente. La rejilla anti-chispa, los tubos de propulsi6n y las bo-quillas deber_n estar instalados en elaparato para estar en total cumplimientocon el reglamento.
CONTENIDO DE LA CAJAVerifique que todos los articulos de lasiguiente lista est6n incluidos:Medelo 358.797342
Propulsor de AireTubo de Propulsi6nTubo en Forma de CodoBolsa de Aspiraci6nTubo de Aspiraci6n SuperiorTubo de Aspiraci6n InferiorAceite de Motor a 2 Tiempos
AMISO: Es normal que el filtro de com-bustible golpetee en el tanque vacio.
MONTAJE
ADVERTENCIA: Detenga elmotor y asegerese de que las cuchil-las del impulsor no se encuentren gi-rando antes de abrir la compuerta deentrada de aire del aspirador o de in-tentar introducir o remover los tubosde aspiraci6n o los tubos de propul-si6n. Las cuchillas girantes podriancausar serios accidentes.
ADVERTENCIA: Si recibi6 elaparato ya armado, repita todos lospasos para asegurarse que el aparatohaya sido armado correctamente yque todos los fijafores se encuentrenbien fijos.• Un destornillador se requiere para el
montaje.
MONTAJE DEL PROPULSORDE AIRE
INSTALACION DEL TUBO DE PRO-PULSION
Si usted ya ha montado el aparatopara el use come aspiradora, remuevalos tubos de ]a aspiradora y la bolsade colecci6n.1. Alinee la moldura saliente del tubo
de propulsi6n con la ranura en lasalida de aire del propulsor; girehasta encajar en su lugar.
AVISO: La perilla debe ser aflojada Iosuficiente que permita al tubo se
introduzca en la salida de aire de lapropulsora. Gire la perilla hacia la iz-quierda para aflojar.
Salida de Aireel Propulsi6n Tubo de
Propulsi6n
Ranura _ Moldura saliente
2. Aseg_rese de apretar el tube algirar la perilla hacia la derecha.
3. Para remover el tubo, gire la perillahacia la izquierda para aflojar eltubo de propulsi6n; remueva eltubo.
MONTAJE DEL ASPIRADOR DEAIRE
MONTAJE DE LA BOLSA DE ASPI-RAClON1. Abra la cremallera en la bolsa de
aspiraci6n e introduzca el tubo enforma de codo.
2. Empuje la punta pequeSa del tuboen forma de codo por la aberturapequeSa el la bolsa de aspiraci6n.
Tubo en formade Codo Abertura
pequeSa
Abe_ura deC_malle_ Moldura Saliente
AVISO: Aseg_rese de que el borde dela abertura pequeSa de la bolsa de en-cuentre pegado a la parte en forma deembudo del tube en forma de codo, yla moldura saliente del tube en formade cedo se encuentre al fondo.3. Cierra la cremallera de la bolsa.
Aseg_rese de que la cremallera seencuentre completamente cerrada.
4. Retire el tubo de propulsi6n.
- 20 -
Moldura
ilanura
5, Introduzca el tubo en forma decodo en la salida de aire delpropulsi6n. Aseg_rese de que lamoldura del tubo en forma de codoest6 alineada con la ranura desalida de aire del propulsi6n.
6, Gire la perilla hacia la derechapara apretar el tubo en forma decodo,
MONTAJE DEL TUBO DEASPIRACION1, Alinee el tubo de aspiraci6n inferior
como se ilustra. Introduzca el tubode aspiraci6n inferior dentro deltubo de aspiraci6n superior,
Tubo de aspiraci6nsuperior
Tubo de aspiraci6ninferior
2, Introduzca un destornillador dentrodel _rea del cerradura de laentrada de aire del aspirador,
Area del cerradura Salida de Aire
_ _., Areadel-II---._del cerraduraCubiertaPropulsi6nde
Entrada de Aire
0e,A,0, a0o
5, Coloque los ganchos que seencuentran en el tubo deaspiraci6n superior en el poste deretenci6n del aparato.
6, Gire el tubo hasta que este fijo por]a cerradura de la entrada de aire.
CerraduraPIVOTE de la
Poste deRetenci6n
COMO CONVERTIR EL APARATO DEUSO DE ASPIRACION A USO DEPROPULSION1. Remueva los tubos de aspiraci6n
introduciendo el destornilladordentro del brea del cerradura de laentrada de aire.
2. Suavemente, gire el mango deldestornillador hacia la parte traseradel aparato para abrir el cerradura,mientras jala hacia arriba el tubode aspiraci6n superior con su otramano,
Area del cerradura
3, Suavemente, gire el mango deldestornillador hacia la parte traseradel aparato para abrir ]a cerradura,mientras jala hacia arriba de lacubierta de la entrada de aire delaspirador con su otra mano.
4, Sostenga la cubierta de entrada deaire del aspirador abierta hastaque el tubo de aspiraci6n quedeinstalado,
3, Remueva la bolsa de aspiraci6n.4, Cierre la cubierta de entrada de
aire del aspirador y aseg0rese queeste cerrada completamente,
-21 -
5. Vuelva a instalar los tubo depropulsi6n (vea INSTALACION DELTUBO DE PROPULSION).
AJUSTE DE LA BANDA DEL HOMBRO(para uso con el aspirador t_nica-mente)1. Sujete el aparato como se ilustra
con el lado del silenciador alejadode su cuerpo y de su ropa.
2. Pasando la banda del hombrosobre su cabeza, col6quela en suhombro derecho.
3. Extienda el brazo izquierdo hacia]a perte posterior de la bolsa de as-piraci6n.
4. Ajuste la correa de hombro hastaque la costura entre la bolsa de as-piraci6n y la correa quede entre elpulgar y el indice.
5. AsegDrese de que el aire circulelibremente desde el tubo en formade codo hasta la bolsa. Si la bolsase encuentra torcide, el aparato nofuncionar_ apropiadamente.
CONOZCA SU PROPULSORLEA EL MANUAL DE INSTRUCClONES Y SUS REGLAS DE SEGURIDAD ANTES DECOMENZAR A USAR ESTE APARATO, Compare las ilustraciones siguientes con suaparato para familiarizarse con la Iocalizaci6n de los controles y ajustes del mis-mo, Guarde este manual para futuras referencias,CUCHILLAS DESMENUZADORASSu propulsor viene equipado con cuchillas desmenuzadoras como caracteristicastandard, Cuando use este accesorio opcional del aspirador, las cuchillas des-menuzadoras reducir_n los escombros en una proporci6n de hasta 16:1.
Tubo superior del_
aspirador ,_-_.""_ _1Tubo inferior del .._-.-.-_ ( _ _ _"
asplrad_/._ _
Bombeador Palanca delCebador
Tapa de laMezcla de
Palanca del Combustible
Tubo en formade Codo
Tubo dePropulsi6n
\ MangoTrasero
- 22 -
PALANCA DEL ACELERADORLa PALANCA DEL ACELERADOR se usopara seleccionar la velocidad deseaday para detener el motor. Mueva la pa-lanca del acelerador a la posici6npara m_xima velocidad. Mueva la pa-lanca del acelerador a la posici6npara conseguir la marcha lent& Paradetener el motor, mueva la palanca delacelerador a la posici6n STOEBOMBEADOREl BOMBEADORes usado para removeraire de el carburador y de las lineas decombustible y las Ilena de mezcla decombustible. Esto le permite poner el
motor en marcha con menos firones dela cuerda de arranque. Active el botondel bombeador apret_ndolo y huegodejando que retome su forma original.PALANCA DEL CEBADOREl CEBADOR ayuda a suiministrar com-bustible al motor para facilitar el arran-que cuando el motor est_ frio. Acione elcebador colocando la palanca en la po-sici6n FULL CHOKE. Despu6s que el mo-tor intente arrancar, mueva la palancadel cebador a la posici6n HALF CHOKE.Despu6s que el motor se haya puestoen march& ponga la palanca del ceba-dor en la posici6n RUN.
SUGERENCIAS UTILES• AI usar el aparato para soplar o para
aspirar los escombros, sujete el apa-rato por el lado del silenciador aleja-do de su cuerpo y de su ropa (yeaPOSIClON DE USO debajo).
• Se requiere que se use protecci6nde oidos para reducir el riesgo de lap6rdida de la audici6n asociado conlos niveles de sonido.
• Detenga el motor antes de instalar oremover accesorios para reducir elriesgo asociado con el contacto delas piezas girantes. No use este apa-rato sin antes tener todos los protec-tores en su lugar.
• Use el equipo de fuerza t]nicamenteen horas razonables - no muy tem-prano en la mafiana o muy tarde enla noche cuando otras personaspodrian ser perturbadas. Cumplacon el horario enlistado por los esta-tutos locales. Usualmente se recom-ienda un horario normal de 9:00 a.m.a 5:00 p.m., de lunes a s_bado.
• Limite el uso de nDmero de piezasde equipo al mismo tiempo para re-ducir los niveles de ruido.
• Para efectuar el trabajo, use los pro-pulsores de fuerza a la menor veloci-dad de aceleraci6n posible para re-ducir los niveles de sonido.
• Use rastrillos y escobas para aflojarescombros antes de soplados con elporpulsor de aire.
• En condiciones de mucho polvo,moje ligeramente las superficies delsuelo o use el accesorio "mister"donde haya agua disponible.
• Conserve agua usando el propulsoren lugar de mangueras de agua
para las tantas aplicaciones delc6sped y de jardineria, incluyendo_reas como Io son canales de aguaen los techos, protecci6n de telamet_lica en las ventanas y puertas,patios, asadores a la parrilla, badcones y jardines.
• Tenga cuidado con los nifios, ani-males dom6sticos, ventanas abier-tas y carros reci6n lavados. Soplelos escombros con precauci6n.
• Use la extensi6n completa de la bo-quilla del propulsor para que la cor-riente de aire pueda trabajar cercadel suelo.
• Despu6s de usar los propulsores deaire y otto tipo de equipo, iLIMPIE!Deseche los escombros en re-cept_culos de basura.
POSICION DE USO
Propulsor AspiradorANTES DE PONER EL MOTOR ENMARCHA
_, ADVERTENCIA: Aseg0rese dehaber leido toda la informaci6n sobre elcombustible en las reglas de seguridadantes de comenzar. Si no comprende]as regias de seguridad, o intenteabastecer el aparato con combustible.Llame al 1-800-235-5878.
- 23 -
ABASTECIMIENTO DEL MOTOR
ADVERTENClA: Remueva la
tapa del tanque de combustible lenta-mente al reabastecer combustible.
Este motor est_ habilitado parafuncionar con gasolina sin plomo. Antesde comenzar con el uso, se deber_mezclar la gasolina con un aceite desint6tico de buena calidad para motoresde 2 tiempos enfriados a aire.Recomendamos el aceite de sint6ticode la marca Craftsman. Mezcle lagasolina con el aceite en la proporci6n40:1. Se obtiene una proporci6n de 40:1mezclando 3,2 onzas de aceite concada gal6n de gasolina sin plomo. Seincluye con esta aparato un recipientede 3,2 onzas de aceite. Adiera elcontenido entero de este recipiente en 1gal6n de gasolina para alcanzar lamezcla apropiada del combustible. NOUSE aceite para autom6viles ni parabarcas. Estos aceites daSar_n elmotor.AI mezclar el combustible, siga ]asinstrucciones impresas en el recipiente.Una vez haya aSadido el aceite a lagasolina, agite al recipiente brevementepara asegurar que el combustible est6completamente mezclado. Siempre leay siga las instrucciones de seguridadque tienen que ver con el combustibleantes de abastecer el aparato.
IMPORTANTELa experiencia indica que los combus-tibles mezclados con alcohol, (los Ila-mados gasohol o los que tienen etanolo metanol) pueden atraer humedad, Ioque puede causar la separaci6n y laformaci6n de _cidos durante el alma-cenaje. La gasolina _cida puede daSarel sistema de combustible del motordurante el almacenaje.Para evitar problemas con el motor,deber_ vaciarse el sistema de com-bustible antes de almacenar el aparatopor 30 dias o m_s.Vacia el tanque de combustible, pongael motor en marcha y d6jelo en mar-cha hasta que las lineas de combus-tible y el carburador queden vacios.Use combustible fresco en la pr6ximatemporada.Nunca use productos de limpieza demotor o carburador en el tanque decombustible ya que de hacerlo puedeprovocar daSos permanentes.Un estabilizador de combustible esuna alternativa aceptable para minimi-zar la formaci6n de dep6sitos de goma
en el combustible durante el almace-naje. El aceite de la marcha Craftsmanviene ya mezclado con estabilizadorde combustible. Vea la secci6n de AL-MACENAJE para m_s informaci6n.
AVI80: El aparato se debe porter delack) al agregar el combustible (vea lailustraci6n abajo).
PARA DETENER EL MOTOR• Para detener el motor, mueva la pa-
]anca del acelerador a la posici6nSTOP.
PARA PONER EN MARCHAEL MOTOR
ADVERTENClA: Es OBLIGATO-RIO asegurarse que los tubos est6nbien fijos antes de usar el aparato.• Abastezca el motor. Ap_rtese por Io
menos 3 metros (10 pies) del lugarde abastecimiento.
• Sostenga el aparato en la posici6nde arranque elustrada. AsegDresede que la boquilla de propulsi6n noest6 direccionada hacia personas,animales, vidrieras y otros objetoss61idos.
POSICION DE ARRANQUE
Propulsor _
Aspirador
- 24 -
ADVERTENCIA: AI arrancar el
motor, sostenga el aparato como seilustra en la figura. Apoye el aparatoexclusivamente en una superficie lim-piay s61ida siempre que vaya a efec-tura el arranque y siempre que tengaque apoyar el aparato con el motor enmarcha. Los escombros tales comogravilla, arena, tierra, c6sped, etc.,pueden ser succionados por la entra-da de aire y arrojados por la salida depropulsi6n, da5ando el aparato u otrosbienes o causando graves heridas aespectadores o al usuario.PARA ARRANCAR CON MOTORFRIO (o motor caliente despu6s dequedar sin combustible)1. Lentamente, presione el bot6n del
bombeador 8 veces.2. Mueva la palanca del cebador a la
posici6n FULL CHOKE.3. Mueva la palanca del acelerador a
la posici6n _.
Palanca del Boron delacelerador bombeador
Palanca del cebado_
4. Firmemente, tire del mango de lacuerda de arranque hasta que elmotor intente arrancar, pero nom_s de 5 tirones (en temperaturesbajo los 30° F, 8 tirones).
AVISO: Si el motor intenta arancarantes del quinto tir6n del mango, paseal siguiente paso de inmediato.5. Mueva la palanca del cebador a la
posici6n HALF CHOKE.6. Firmemente, tire del arranque has-
ta que el motor arranque, pero nom_s de 5 tirones (en temperaturesbajo los 30° F, 10 tirones).
7. Despu6s de calentar por 5 segun-dos, mueva la palanca del cebadora la posici6n RUN.
8. Permita que el aparato siga enmarcha por otros 30 segundos enla posici6n RUN antes de mover lapalanca del acelerador a la posi-ci6n _.
Si el motor no ha arrancado despu6sdel quinto tir6n del mango de arranque(en la posici6n HALF CHOKE), repita elprocedimiento PARA ARRANCAR CONMOTOR FRIO. Si el motor persiste sinarrancar, proceda con el procedimien-to baho el titulo ARRANQUE DE MOTORAHOGADO.9. Para detener el motor, mueva la pa-
lanca del acelerador a la posici6nSTOR
PARA ARRANCAR CON EL MOTORCALIENTE1. Mueva la palanca del acelerador a
la posici6n _.2. Firememente, tire del mango de ar-
ranque hasta que el motor arran-que, pero no m_s de 5 tirones.
AVIS0: Si el motor no arranca, tire delmango de arranque firmemento otras5 veces. Si el motor persiste sin arran-car, probablemente se encuentre aho-gado. Proceda con la secci6n ARRAN-QUE DE MOTOR AHOGADO.3. Para detener el motor, mueva la pa-
]anca del acelerador a la posici6nSTOR
ARRANQUE DE MOTOR AHOGADOLos motores que se encuentren ahoga-dos podr_n ponerse en marcha colo-cando la palanca del cebador en la po-sici6n RUN. Mueva la palanca del acel-erador a la posici6n _ ; luego, itre dela cuerda de arranque hasta que el mo-tor se ponga en marcha. Despu6s queel motor se haya puesto en marcha,mueva la palanca del acelerador a laposici6n _ para permitir que el motorquede en marcha lenta.Para que el motor arranque, posible-mente tendr_ que tirar de la cuerda dearranqeu muchas veces. Esto de-pende de cu_n ahogado se encuentreel motor.Si el aparato persiste sin arrancar, veala TABLA DIAGNOSTICA de este manualo Ilame al 1-800-235-5878.
- 25 -
RESPONSABILIDAD DEL USUARIO
ADVERTENCIA: Desconecte la bujia antes de realizar mantenimiento,servicio, o ajustes.
TAREA DE CUIDADO Y MANTENIMIENTO
Verificar que no haya fijadores flojos ni piezas sueltas
Verificar que no haya piezas daSadas o gastadasInspeccione y limpie el aparato y sus placasLimpiar el filtro de aire
Inspeccione silenciador y la reiilia antichispa
Cambie la buiiaCambie el filtro del combustible
Verifique los tornillos del silenciador
CUANDO HACER
Antes de cada uso
Antes de cada uso
Despu6s de cada usoCada 5 horas de use
Cada 50 horas de use
AnualmenteAnualmente
Anualmente
ADVERTENCIA: Evite hacercontacto con el silenciador a no serque el motor y el silenciador se en-cuentre frio. El contacto con un silen-ciador caliente puede causar quema-duras de gran envergadura.
ADVERTENClA: Detenga elmotor y asegerese de que las cuchil-]as del impulsor no se encuentren gi-rando antes de abrir ]a compuerta deentrada de aire del aspirador o de in-tentar introducir o remover los tubosde aspiraci6n o los tubos de propul-si6n. Las cuchillas girantes podriancausar series accidentes. Siempredesconecte ]a bu ia antes de hacer cu-a qu er manten m ento o de tener ac-ceso a piezas movibles.RECOM ENDAClONES GENERALESLa garantia de este aparato no cubrelos articulos que hart side sometidos alabuso o a la negligencia por parte delusuario. Para recibir el valor completede la garantia, el usuario deber_ man-tener el aparato segQn las instruc-clones en este manual. Har_ falta hac-er varies ajustes peri6dicamente paramantener el aparato de forma debida.
VERIFICA£ QUE NO HAYAPIEZAS SUELTAS NI FIJADORESFLOJOS, Capucha de la Bujia, Filtro de Aire• Tomillos de la CajaVERIFICAR QUE NO HAYA PIEZASDANADAS NI GASTADASEntre en contacto con el Centro deServicio Sears para el reemplazo depiezas daSadas o desgastadas.
* Palanca del acelerador- AsegQresede que la palanca del acelerador fun-clone de forma apropiada movi6ndolaa la posici6n STOR Aseg_rese de queel motor se detenga; ]uego, vuelva aporter en marcha el motor y continue.
* Tanque de Combustible. Para de usarel aparato si hay indicios de daSos op6rdidas en el tanque de combustible.
* Bolsa de la Aspiradora. Pare de usar]a bolsa de aspiraci6n si se encuen-tra de alquna manera rota o daSada.
INSPECCIONE f MMPIE EL APARA-TO Y SUS PLACAS, Despu6s de que cada use, inspec-
clone la aparato completa para sabersi hay piezas flojas o daSadas. Limpieel aparato y las placas usando un tra-po h_medo con un detergente suave.
, S6quelo con un trapo limpio.LIMPIE EL FILTRO DE AIRE
del Filtrode Aire
_"/ Filtro de Aire Tornillos
Los filtros de aire sucios disminuyen elrendimiento del motor e incrementanel consumo de combustible y la pro-ducci6n de emisiones nocivas.
- 26 -
Siempre limpie el filtro de aire despu6sded cada 5 horas de uso.Limpieza del filtro del aire:1. Limpie la cubierta y el _rea conti-
gua para evitar que caiga tierra en]a c_mara del carburador cuandoremueva la cubierta.
2. Retire las piezas como se ilustra.AVISO: No limpie el filtro de aire congasolina ni ning_n otro solvente in-flamable, ya que de hacerlo puedecrear peligro de incendio y de emi-clones evaporativas nocivas.3. Lave el flltro con agua y jab6n.4. Permita que el filtro se seque.5. Aplique varias gotas de aceite al fil-
tro; a oprima el filtro para distribuir elaceite.
6. Reponga las piezas.GAMBLE LA BUJIACambie la bujia anualmente. La sepa-raci6n de los electrodos de la bujiadeber_ ser de 0,025 de pulgada. Elencendido es fijo y no es ajustable.1. Gire y luego retire la capucha de la
bujia.2. Retire la bujia del cilindro y des6-
chela.3. C&mbiela por una bujia CJ-6Y y
aj_stela con una nave de 3/4 de pul-gada.
4. Vuelva a instalar la capucha.GAMBLE EL FILTRO DELCOMBUSTIBLEPara cambiar el filtro del combustible,vacie el aparato de todo combustibledejando el motor en marcha hasta quese detenga. Luego, remueva el mon-taje de la tapa/retenedor del tanque.Tire del filtro que se encuentra en eltanque y retirelo de la linea de com-bustible. Instale un filtro nuevo en la]inea de combustible; vuelva a instalartodas las piezas.
_ Linea de
bustible
Filtro delCombustible
VERIFICAR LOS TORNILLOS DEMONTAJE DEL SILENCIADORPara prevenir da_os, aseg_rese anu-almente de que los tornillos de mon-taje del silenciador se encuentren se-guros y apropiadamente ajustados.
Huecos de losTornillos de
Tapa del Montaje delSilenciador_, Silenciador
Tornillos
1. Afloje y retire los 2 tornillos de latapa del silenciador.
2. Remueva la tapa del silenciador.3. Apriete firmemente los 2 tornillos de
montaje.4. Reinstale la tapa del silenciador y
los 2 tornillos. Apriete flrmemente.AJUSTE AL CARBURADORNo hay tornillo para el ajuste de lamarcha lenta en su propuisor de aire.La palanca del acelerador se utilizapara ajuste de las revoluciones de lamotor. La palanca del acelerador sepuede colocar en una de cuatroposiciones: PARE, MARCHA LENTA o
, ACELERADOR ABIERTO o _', yuna posici6n intermitente. Si su motorno funciona correctamente o si ustednecesita m_s ayuda, entre en contactocon un Centro de Servicio Sears o]lame a nuestro tel6fono de ayuda alconsumidor, al 1-800-235-5878.
- 27 -
ADVERTENCIA: Realice los si-guientes pasos despu6s de cada uso:• Permita que el motor se enfrie y fije
bien el aparato antes de guardarlo otransportado.
• Guarde el aparato y el combustibleen un lugar bien ventilado donde losvapores de combustible no puedanentrar en contacto con chispas o lla-mas abiertas provenientes de termo-tanques, motores o interruptoresel6ctricos, calefactores centrales,etc.
• Guarde el aparato con todos los pro-tectores en su lugar y coloque elaparato de modo que las piezas filo-sas no puedan causar heridas poraccidente.
• Guarde el aparato y el combustiblecompletamente fuera del alcance delos ni_os.
ESTACIONAL ALMACENAJEPrepare el aparato para el almacenajeal final de la temporada o si ca a estarsin usar por m_s de 30 dias.Si va a almacenar el aparato duranteun periodo largo de tiempo:• Limpie el aparato por completo antes
del almacenaje.• Almacene en un _rea limpia y seca.• Aplique una pequeSa cantidad de
aceite alas superficies externasmet_licas.
SISTEMA DE COMBUSTIBLEBajo el ABASTECIMIENTODEL MOTOR,en la seccion de USO de este manual,vea el mensaje marchado como IM-PORTANTE referente al uso de gasoholen su motor. Los estabilizadores decombustible son una altemativa acept-
able para minimizar la formaci6n delos depositos de goma durante el al-macenaje. ASada estabilizador a la ga-solina en el tanque de combustible o enel recipiente para alacenaje de combus-tible. Siga las instrucciones de mezclaque se encuentran en los envases delestabilizador. Ponga el motor en marchay d6jelo en marcha por Io menos 5 mi-nutos despu6s de haberle puesto el es-tabilizador.El aceite de la marca Craftsman 40:1para motores a 2 tiempos (enfriados aaire) ya viene mezclado con estabiliza-dor de combustible. Si no usa esteaceite, entonces puede aSadir un es-tabilizador al tanque de combustible.
MOTOR• Retire la bujia y vierta una cucharad-
ita de aceite 40:1 para motores de 2tiempos (enfriados a aire) por la ab-ertura de la bujia. Lentamente tire dela cuerda de arranque de 8 a 10veces para distribuir el aceite.
• Reemplace la bujia con otra nuevadel tipo y de la gama de calor recom-endados.
• Limpie el filtro de aire.• Examine todo el aparato para verifi-
car que no hayan tornillos, quebra-
• das o gastadas.AI principio de la pr6xima temporada,use exclusivamente combustiblenuevo con la proporci6n correcta degasolina y aceite.
OTROS• No guarde la gasolina de una tempo-
rada a la siguiente.• Cambie el recipiente de gasolina si
se empieza a oxidar.
- 28 -
TABLA DIAGNOST|CA
ADVERTENCIA: Siempre apague el aparato y desconecte la bujfa antesde hacer cuaiquiera de Ins reparaciones recomendadas a continuaciEn que
SINTOMA
El motor noarranca.
El motor noanda enmarcha lentacomo debe.
El motor noacelera, lefaltapotencia ose para bajocarga.
El motorhumea ex-cesiva-mente
El motormarcha con
temperaturaelevada.
no requieran que la unidad est6 en c
CAUSA
1, El motor est_ ahogado,
2, El tanque de combustibleest& vacio.
3, La bujfa no est_ haciendochispa.
4, El combustible no est&Ilegando al carburador.
5, La compresion est_ baja.
1. El combustible no est_Ilegando al carburador.
2. El carburador requierajuste.
3. Las lunas del cigueEalestan gastadas.
4. La compresi6n est& baja,
1. El filtro de aire est_ sucio,2. El combustible no est_
Ilegando al carburador,
3. La bujia est& carbonizada.
4. El carburador requiereajuste,
5. Acumulacion de carbon.
6. La compresi6n est_ baja.
1. El cebador esta parcial-mente accionado.
2. La mezcla de combustiblese ha hecho incorrecta-mente.
3. El filtro de aire est_ sucio,4. El carburador requiere
ajuste,
1. La mezcla de combustibleesta se he hechoincorrectamente,
2. Se ha instalado la bujlaincorrect&
3. El carburador requiereajuste.
4. Acumulaci6n de carb6n,
)eraciEn.
SOLUCION
1, Vea "Arranque de Motor Ahogado"en la secci6n Uso.
2, Llene el tanque con la mezclacorrecta de combustible.
3, Instale una bujia nueva.
4, Verifique si el filtro de combustible noest6 sucio; c_mbielo. Vedfique si haydobleces en la linea de combustibleo si est_ partida; reparela o c_mbiela.
5, Entre en contacto con el ServicioSears (vea parte trasera del manual).
1. Verifique si el filtro de combustible noest6 sucio; c&mbielo. Vedfique si haydobleces en la Ifnea de combustibleo si est_ partida; rep_rela o c&mbiela.
2. Entre en contacto con el ServicioSears (vea parte trasera del manual),
3. Entre en contacto con el ServicioSears (vea parte trasera del manual),
4. Entre en contacto con el ServicioSears (vea parte trasera del manual),
1, Limpie o cambie el filtro de aire.2, Verifique si el filtro de combustible no
est6 sucio; c_mbielo. Verifique si haydobleces en la linen de combustibleo siesta partida; reparela o c_mbiela.
3, Limpie o cambie la bujfa y calibrela separaci6n.
4, Entre en contacto con el ServicioSears (vea parte trasera del manual).
5, Entre en contacto con el ServicioSears (vea parte trasera del manual).
6, Entre en contacto con el ServicioSears (yea parte trasera del manual).
1. Ajuste el cebador.
2. Vaci6 el tanque de combustible y116nelo de combustible con la mezclacorrecta.
3. Umpie o cambie el filtro de aire.4. Entre en contacto con el Servicio
Sears (vea parte trasera del manual),
1. Yea "Abastecimiento del Motor" en [aseccion Uso.
2. Cambie por la bujfa correcta.
3. Entre en contacto con el ServicioSears (vea parte trasera del manual).
4. Entre en contacto con el ServicioSears (vea parte trasera del manual).
- 29 -
SUS DERECHOS Y OBUGACIONESDE GARANTIA: La Agencia de Pro-tecci6n Ambiental de los Estados Uni-dos y Sears, Roebuck and Co.,U.S.A., se cemplacen en explicar lagarantia con la que cuenta el sistemade control de emisi6n en su motor pe-queSo, modelo 2002-2004, para usofuera de carretera. Sears deber_ ga-rantizar el sistema de control de emi-si6n en su m_quina de motor pequeSopara uso fuera de carretera por losper(odos de tiempo que explicamos acentinuaci6n y con la condici6n de quesu m_quina de motor pequeSo parauso fuera de carretera no haya sufridoningt]n tipo de abuso, negligencia omantenimiento inapropiado. Su siste-ma de control de emisi6n incluye pie-zas tales como el carburador y el sis-tema de ignici6n. Donde exista unacendici6n que requiera reparaci6nbajo garantia, Sears reparar_ gratis sumotor pequeSo para use fuera de car-retera. Los gatos cubiertos bajo la ga-rant_a incluyen el diagn6stico, las pie-zas y labor. CUBIERTA DE GARAN-TIA DEL FABRICANTE: Si cualquierpieza relacionada con el sistema deemisi6n de su motor (come hemos en-umerado en la lista de piezas de con-trol de emisi6n bajo garantia) se en-contrara defectuosa o defectos en elmaterial o en la labor del motor causa-ran que tal pieza comenzara a fallar, lapieza ser_ reparada o reemplazadapor Sears. GARANTIA DE RESPON-SABILIDAD DE DEL DUENO: ComodueSo de una m_quina de motor pe-queSo para uso fuera de carretera,usted ser_ responsable por el manten-imiento adecuado en los periodos pre-viamente programados y enumeradosen su manual de instrucciones. Searsrecomienda que guarde todos los reci-bos que indiquen que se ha de-sempeSado mantenimiento en sum_quina de motor pequeSo para usofuera de carretera, pero Sears nopodr_ negar el servicio bajo garantiat_nicamente a causa de la falta de reci-bos o por el incumplimiento de suparte en asegurarse que el mantenimi-ento programado haya sido de-sempeSado. Come dueSo de unam_quina de motor pequeSo para usofuera de carretera, usted deber_ con-
tar con el conocimiento de que Searspuede negar la cubierta bajo garantiasi su m_quina de motor pequeSo parauso fuera de carretera o alguna piezade la misma ha dejado de funcionardebido al abuso, negligencia, manten-imiento inapropiado, modificacionesno aprobadas o el use de piezas queno hayan sido fabricadas o aprobadaspor el fabricante original del equipo.Es responsabilidad suya el Ilevar sum_quina de motor pequeSo para usofuera de carretera a un centro de repa-raci6n autorizado Sears tan prontocemo se presente el problema. Lasreparaciones bajo garantia deber_nser completadas en un pedodo detiempo razonable, que no exceda los30 dias. Si cuenta usted con algunapregunta en relaci6n a sus derechos yresponsabilidades de garantia, usteddeber_ comunicarse con su distribui-dor autorizado del servicio m_s cerca-no o Ilamar a Sears al1-800-469-4663. FECHA DELCOMIENZA DE LA GARANTIA: Elpedodo de garantia comienza en lafecha de compra de la m_quina demotor pequeSo para use fuera de car-retera. DURAClON DE LA GARAN-TIA: Esta garantia cuenta con un per-iodo de duraci6n de dos amos cemen-zando en la fecha inicial de compra.QUE CUBRE LA GARANTIA: REPA-RACION O REEMPLAZO DE PIE-ZAS. La reparaci6n o el reemplazo decualquier pieza garantizada ser_n de-sempeSados y ofrecidos al dueSo sincesto alguno en un distribuidor auteri-zado del servicio Sears. Si cuentausted con alguna pregunta en relaci6na sus derechos y responsabilidadesde garantia, usted deber_ comuni-carse con su distribuidor autorizadodel servicio m_s cercano o Ilamar aSears al 1-800-469-4663. PERIODODE GARANTIA: Cualquier pieza ga-rantizada que no est6 programadapara ser reemplazada como parte delmantenimiento requerido, o que est6programada t_nicamente para inspec-ci6n regular para efectos de "repara-ci6n o reemplazo si fuera necesario"deber_ garantizarse por un periodo dedos aSos. Cualquier pieza garantiza-da que est6 programada para ser re-emplazada come parte del mantenimi-
- 30 -
ento requerido deber_ estar garantiza-da por el periodo de tiempo que com-ienza en la fecha de compra inicialhasta la fecha de] primer reemplazoprogramado para dicha pieza. DIAG-NOSTICO: No se deber_ cobrar aldueSo ningDn tipo de cargos por la la-bor de diagn6stico la cual determineque una pieza garantizada se encuen-tra defectuosa si el trabajo dediagn6stico ha sido desempeSado porun distribuidor autorizado del servicioSears, DANOS POR CONSECUEC|A:Sears podr_ ser responsable dedaSos ocurridos a otras piezas del mo-tor causados por la falla de una piezagarantizada que se encuentre bajo elperiodo de garantia. QUE NOCUBRE LA GARANTIA: Todas las fal-]as causadas por el abuso, negligen-cia o mantenimiento inapropiado noest_n cubiertas. PIEZAS ANADIDASO MODIFICADAS: El uso de piezasaSadidas o la modificaciSn de piezaspodr_n servir como base para que seanule la reclamaci6n de garantia. Lagarantia de Sears no se responsabili-za por el real funcionamiento debido aluso de piezas aSadidas o de piezasmodificadas. COMO ENTABLARUNA RECLAMAClON: Si cuentausted con al,quna pre,qunta relaciona-
da con sus derechos y responsabili-dades de garantia, usted deber_ en-trar en contacto con su distribuidor au-torizado del servicio Sears m_s cerca-no o Ilamar a Sears a]1-800-469-4663. DONDE OBTENERSERVlClO DE GARANTIA: Servicio oreparaciones bajo garantia deber_nser provistas en todos los distribuidorsautorizado del servicio Sears. Por fa-vor comuniquese al 1-800-469-4663.MANTENIMIENTO, REEMPLAZO YREPARACION DE PIEZAS RELA=CIONADAS CON LA EMISION: Cual-quier pieza de repuesto Sears aproba-day utilizada en el desempeSo de cu-alquier servicio de mantenimiento oservicio de reparaci6n bajo garantiade piezas relacionadas con la emisi6nser_ provisto sin costo alguno a]dueSo si la pieza se encuentra bajogarantia. LISTA SE PIEZAS DE CON-TROL DE EMISION GARANTIZA-DAS: Carburador, Sistema de Ignici6n:Bujia (cubierta hasta la fecha de man-tenimiento programada), M6dulo deIgnici6n. DECLARACION DE MAN-TENIMIENTO: E] dueSo es respons-able de adquirir todo el mantenimientorequerido como 1odefine en el manualde instrucciones.
Se certifica este motor para satisfacer los requisitos de emisi6n para los usosiguientes:
[] Moderado (50 horas)
[] Intermedio (125 horas)
[] Extendido (300 horas)
- 31 -
CRAFTSMAN | Model #358797342 | BLOWER | CYLINDER/CRANKCASE/CRANKSHAFT... http://partsdirect.com/partsdirect/retrieveSubComponentPartsAction.action?diagramPageId=0...
1 of 7 2/20/2008 3:48 PM
Part results for: CYLINDER/CRANKCASE/CRANKSHAFT
View diagram
CRAFTSMANBLOWERModel# 358797342Return to Sub Components
Enter Keyword Clear
# Part # Description Price & Availability
# Part # Description Price & Availability
1
N/P
(champion) spark plug (rcj-6y) Discontinued
2
530015953
Screw $2.91 In stock
Qty
3
530016387
Screw-muffler-internal $2.91 In stock
Qty
4
530015241
Screw $2.91 In stock
Qty
5
530071593
Kit-spark screen (incl. #5) $5.94 In stock
Qty
6
530071834
Kit-muffler (incl. 3, 4, 5 and 7) $14.08 In stock
Qty
1
1
1
1
1
CRAFTSMAN | Model #358797342 | BLOWER | CYLINDER/CRANKCASE/CRANKSHAFT... http://partsdirect.com/partsdirect/retrieveSubComponentPartsAction.action?diagramPageId=0...
2 of 7 2/20/2008 3:48 PM
# Part # Description Price & Availability
7
530071458
Gasket-baffle (gasket kit) $4.94 In stock
Qty
8
530071458
Gasket-cylinder (gasket kit) $4.94 In stock
Qty
9
530071457
Kit-cylinder $28.25 In stock
Qty
10
530019182
Grommet-ign. module $2.91 In stock
Qty
11
530016357
Screw-ignition module $2.91 In stock
Qty
12
530035505
Ignition module $25.81 In stock
Qty
13
530071833
Kit-piston (incl. 14 and 15) $22.79 In stock
Qty
14
530055120
Piston ring $2.91 In stock
Qty
15
530015162
Retainer-piston pin $2.91 In stock
Qty
16
530069945
Assembly-connecting rod $9.14 In stock
Qty
17
530071615
Kit-crankcase seal $4.93 In stock
Qty
1
1
1
1
1
1
1
1
1
1
1
CRAFTSMAN | Model #358797342 | BLOWER | CYLINDER/CRANKCASE/CRANKSHAFT... http://partsdirect.com/partsdirect/retrieveSubComponentPartsAction.action?diagramPageId=0...
3 of 7 2/20/2008 3:48 PM
# Part # Description Price & Availability
18
530055728
Outer bearing $4.93 In stock
Qty
19
530015941
Retainer ring-c'shaft $2.91 In stock
Qty
20
530016190
Flywheel spacer $2.91 In stock
Qty
21
530015149
Washer $2.91 In stock
Qty
22
530039209
Assembly-flywheel $17.68 In stock
Qty
23
530071456
Assembly-crankcase/crankshaft (incl. 19, 24, 26) $40.54 In stock
Qty
24
530012492
Assembly-crankcase (incl. 17, 18, 25) $18.57 In stock
Qty
25
530032125
Bearing-inner $8.61 In stock
Qty
26
530012452
Assembly-crankshaft $18.99 In stock
Qty
27
530071458
O-ring-c/case (gasket kit) $4.94 In stock
Qty
28
530012443
Cover-crankcase $5.94 In stock
Qty
1
1
1
1
1
1
1
1
1
1
1
CRAFTSMAN | Model #358797342 | BLOWER | CYLINDER/CRANKCASE/CRANKSHAFT... http://partsdirect.com/partsdirect/retrieveSubComponentPartsAction.action?diagramPageId=0...
4 of 7 2/20/2008 3:48 PM
# Part # Description Price & Availability
29
530015810
Screw $2.91 In stock
Qty
30
530071459
Foam-219mm (foam kit) $2.91 In stock
Qty
31
530029182
Eyelet-flange $2.91 In stock
Qty
32
530071467
Kit-rope $3.92 In stock
Qty
33
530049488
Handle-starter $2.91 In stock
Qty
34
530016391
Screw-rope $2.91 In stock
Qty
35
530095461
Assembly-mulch blade $7.27 In stock
Qty
36
530626605
Nut $2.91 In stock
Qty
37
530402043
Spring-return cover $2.91 In stock
Qty
38
530049313
Inlet door $4.94 In stock
Qty
39
530016240
Washer-belleville $2.91 In stock
Qty
1
1
1
1
1
1
1
1
1
1
1
CRAFTSMAN | Model #358797342 | BLOWER | CYLINDER/CRANKCASE/CRANKSHAFT... http://partsdirect.com/partsdirect/retrieveSubComponentPartsAction.action?diagramPageId=0...
5 of 7 2/20/2008 3:48 PM
# Part # Description Price & Availability
40
530069817
Kit-impeller assembly $11.40 In stock
Qty
41
530056625
Seal-o-ring $3.92 In stock
Qty
42
530016349
Screw $2.91 In stock
Qty
43
530055101
Housing-pulley $5.94 In stock
Qty
44
545008011
Starter-spring $4.99 In stock
Qty
45
530054425
Kit-starter pulley $7.38 In stock
Qty
46
530055102
Fan housing $7.71 In stock
Qty
47
530015810
Screw $2.91 In stock
Qty
48
530071459
Foam-182mm (foam kit) $2.91 In stock
Qty
49
530071458
Kit-gasket (includes)(page 1-#2 and 5)(page 2-#7,8 and 27) $4.94 In stock
Qty
50
530071459
Kit-foam (includes)(page 1-#1,16 and 31)(page 2-#30 and 48) $2.91 In stock
Qty
1
1
1
1
1
1
1
1
1
1
1
CRAFTSMAN | Model #358797342 | BLOWER | CYLINDER/CRANKCASE/CRANKSHAFT... http://partsdirect.com/partsdirect/retrieveSubComponentPartsAction.action?diagramPageId=0...
6 of 7 2/20/2008 3:48 PM
Adjust the split window by dragging this up and down Hide list
Zoom in Zoom out
View full size| Print
# Part # Description Price & Availability
Not In Diagram
530163801
Operator manual $4.93 In stock
Qty
Not In Diagram
530071726
Kits-throttle lever walbro $6.90 In stock
Qty
Not In Diagram
530071725
Kits-choke lever walbro $6.90 In stock
Qty
Not In Diagram
530071716
Kits-choke lever zama $6.90 In stock
Qty
Not In Diagram
530071715
Kits-throttle lever zama $6.90 In stock
Qty
Not In Diagram
530057414
Warning decal $2.91 In stock
Qty
Not In Diagram
530055811
Decal-start inst. $2.91 In stock
Qty
1
1
1
1
1
1
1
CRAFTSMAN | Model #358797342 | BLOWER | CYLINDER/CRANKCASE/CRANKSHAFT... http://partsdirect.com/partsdirect/retrieveSubComponentPartsAction.action?diagramPageId=0...
7 of 7 2/20/2008 3:48 PM
CRAFTSMAN | Model #358797342 | BLOWER | HOUSING/FUEL TANK/HANDLE | Sears... http://partsdirect.com/partsdirect/retrieveSubComponentPartsAction.action?diagramPageId=0...
1 of 5 2/20/2008 3:50 PM
Part results for: HOUSING/FUEL TANK/HANDLE
View diagram
CRAFTSMANBLOWERModel# 358797342Return to Sub Components
Enter Keyword Clear
# Part # Description Price & Availability
# Part # Description Price & Availability
1
530071459
Air dam (foam kit) $2.91 In stock
Qty
2
530071458
Gasket-adapter (gasket kit) $4.94 In stock
Qty
3
530035561
Adapter-carburetor $9.89 In stock
Qty
4
530016309
Screw $2.91 In stock
Qty
5
530071458
Gasket-carburetor (gasket kit) $4.94 In stock
Qty
6
530071632
Kit-carb assembly zama (c1q-w11c) $26.71 In stock
Qty
1
1
1
1
1
1
CRAFTSMAN | Model #358797342 | BLOWER | HOUSING/FUEL TANK/HANDLE | Sears... http://partsdirect.com/partsdirect/retrieveSubComponentPartsAction.action?diagramPageId=0...
2 of 5 2/20/2008 3:50 PM
# Part # Description Price & Availability
6A
530071775
Kit-carb assembly walbro (wt-606) $26.78 In stock
Qty
7
530056629
Air box $5.94 In stock
Qty
8
530015849
Screw-carb. $2.91 In stock
Qty
9
530049383
Air filter $2.91 In stock
Qty
10
530056581
Air filter cover $2.91 In stock
Qty
11
530016349
Screw $2.91 In stock
Qty
12
530056641
Guard-muffler $5.94 In stock
Qty
13
530095469
Handle $7.27 In stock
Qty
14
530015886
Screw $2.91 In stock
Qty
15
530049323
Isolator $2.91 In stock
Qty
16
530071459
Foam-25.4mm (foam kit) $2.91 In stock
Qty
1
1
1
1
1
1
1
1
1
1
1
CRAFTSMAN | Model #358797342 | BLOWER | HOUSING/FUEL TANK/HANDLE | Sears... http://partsdirect.com/partsdirect/retrieveSubComponentPartsAction.action?diagramPageId=0...
3 of 5 2/20/2008 3:50 PM
# Part # Description Price & Availability
17
530015197
Nut $2.91 In stock
Qty
18
530016322
Knob-tube clamp $2.91 In stock
Qty
19
530057624
Housing-right $19.06 In stock
Qty
20
530402044
Spring cover latch $3.92 In stock
Qty
21
530049617
Guide-starter rope $2.91 In stock
Qty
22
530057627
Housing-left $19.89 In stock
Qty
23
530053725
Isolator-crankcase $2.91 In stock
Qty
24
545058007
Assembly-fuel tank $18.97 In stock
Qty
25
530049527
Gasket-fuel tank $2.91 In stock
Qty
26
530049386
Fuel cap with retainer $5.99 In stock
Qty
27
530049656
Grommet-shroud $2.91 In stock
Qty
1
1
1
1
1
1
1
1
1
1
1
CRAFTSMAN | Model #358797342 | BLOWER | HOUSING/FUEL TANK/HANDLE | Sears... http://partsdirect.com/partsdirect/retrieveSubComponentPartsAction.action?diagramPageId=0...
4 of 5 2/20/2008 3:50 PM
Adjust the split window by dragging this up and down Hide list
# Part # Description Price & Availability
28
530069247
Kit-line carb/purge $3.99 In stock
Qty
29
530069216
Kit-line tank/purge $3.99 In stock
Qty
30
530095646
Assembly-fuel pick-up $2.91 In stock
Qty
31
530071459
Grommet-fuel line (foam kit) $2.91 In stock
Qty
Not In Diagram
530163801
Operator manual $4.93 In stock
Qty
Not In Diagram
530071726
Kits-throttle lever walbro $6.90 In stock
Qty
Not In Diagram
530071725
Kits-choke lever walbro $6.90 In stock
Qty
Not In Diagram
530071716
Kits-choke lever zama $6.90 In stock
Qty
Not In Diagram
530071715
Kits-throttle lever zama $6.90 In stock
Qty
Not In Diagram
530057414
Warning decal $2.91 In stock
Qty
Not In Diagram
530055811
Decal-start inst. $2.91 In stock
Qty
1
1
1
1
1
1
1
1
1
1
1
CRAFTSMAN | Model #358797342 | BLOWER | HOUSING/FUEL TANK/HANDLE | Sears... http://partsdirect.com/partsdirect/retrieveSubComponentPartsAction.action?diagramPageId=0...
5 of 5 2/20/2008 3:50 PM
Zoom in Zoom out
View full size| Print
CRAFTSMAN | Model #358797342 | BLOWER | VACUUM/BLOWER | SearsPartsDirect.co... http://partsdirect.com/partsdirect/retrieveSubComponentPartsAction.action?diagramPageId=0...
1 of 3 2/20/2008 3:51 PM
Part results for: VACUUM/BLOWER
View diagram
CRAFTSMANBLOWERModel# 358797342Return to Sub Components
Enter Keyword Clear
# Part # Description Price & Availability
# Part # Description Price & Availability
1
530095564
Vac bag with strap $21.99 In stock
Qty
2
530095470
Elbow-vac tube $5.94 In stock
Qty
3
530095589
Tube-lower vac $7.85 In stock
Qty
4
530056901
Tube-upper vac $10.22 In stock
Qty
5
530095593
Tube-blower $10.18 In stock
Qty
Not In Diagram
530163801
Operator manual $4.93 In stock
Qty
1
1
1
1
1
1
CRAFTSMAN | Model #358797342 | BLOWER | VACUUM/BLOWER | SearsPartsDirect.co... http://partsdirect.com/partsdirect/retrieveSubComponentPartsAction.action?diagramPageId=0...
2 of 3 2/20/2008 3:51 PM
Adjust the split window by dragging this up and down Hide list
Zoom in Zoom out
View full size| Print
# Part # Description Price & Availability
Not In Diagram
530071726
Kits-throttle lever walbro $6.90 In stock
Qty
Not In Diagram
530071725
Kits-choke lever walbro $6.90 In stock
Qty
Not In Diagram
530071716
Kits-choke lever zama $6.90 In stock
Qty
Not In Diagram
530071715
Kits-throttle lever zama $6.90 In stock
Qty
Not In Diagram
530057414
Warning decal $2.91 In stock
Qty
Not In Diagram
530055811
Decal-start inst. $2.91 In stock
Qty
1
1
1
1
1
1
CRAFTSMAN | Model #358797342 | BLOWER | VACUUM/BLOWER | SearsPartsDirect.co... http://partsdirect.com/partsdirect/retrieveSubComponentPartsAction.action?diagramPageId=0...
3 of 3 2/20/2008 3:51 PM