BH76330FVM,BH76331FVM,BH76360FV,BH76361FV ...rohmfs.rohm.com/.../video_amplifier/bh76330fvm-e.pdfBH76363FV (6input 1output Video Switch) ・・・・・・P17 No.09065EAT01 Technical

1/32 www.rohm.com 2009.04 - Rev.A

© 2009 ROHM Co., Ltd. All rights reserved.

High-performance video signal Switcher Series

Video Drivers with Built-in Low Voltage operation Single Video Switchers High-performance System video Driver Series

Video Drivers with Built-in Input Selection SW BH76330FVM, BH76331FVM, BH76360FV, BH76361FV High-performance video signal Switcher Series

Wide Band Low Voltage operation Single Video Switchers BH76332FVM, BH76333FVM, BH76362FV, BH76363FV

INDEX

Video Drivers with Built-in Low Voltage operation Single Video Switchers BH76330FVM (3input 1output Video Switch)・・・・・・P2

BH76331FVM (3input 1output Video Switch)・・・・・・P2

BH76360FV (6input 1output Video Switch)・・・・・・P17


Wide Band Low Voltage operation Single Video Switchers BH76332FVM (3input 1output Video Switch)・・・・・・P2

BH76333FVM (3input 1output Video Switch)・・・・・・P2



No.09065EAT01

Technical NoteBH76330FVM, BH76331FVM, BH76360FV, BH76361FV,BH76332FVM, BH76333FVM, BH76362FV, BH76363FV



Line-up of products with built-in video amplifier and video driver

3-input, 1-output video switch BH76330FVM, BH76331FVM, BH76332FVM, BH76333FVM General

BH76330FVM, BH76331FVM, BH76332FVM, and BH76333FVM are video signal switching ICs, each with three inputs and

one circuit input, which feature wide dynamic range and frequency response. Since these ICs can be used with low voltage

starting at VCC = 2.8 V, they are applicable not only in stationary devices but also in mobile devices.

This product line-up supports a broad range of input signals, depending on whether or not a 6-dB video amplifier and video

driver are included and what combination of sync tip clamp type and bias (resistor termination) type inputs are used.

Features

1) Able to use a wide range of power supply voltage, from 2.8 V to 5.5 V

2) Wide output dynamic range

3) Excellent frequency response

(BH76330FVM and BH76331FVM: 100 kHz/10 MHz 0 dB [Typ.], BH76332FVM and BH76333FVM: 100 kHz/30

MHz 0 dB [Typ.])

4) No crosstalk between channels (Typ. -65 dB, f = 4.43 MHz)

5) Built-in standby function, circuit current during standby is 0 µA (Typ.)

6) Sync tip clamp input (BH76330FVM, BH76332FVM)

7) Bias input (Zin = 150 k) (BH76331FVM, BH76333FVM)

8) 6-dB amp and 75 driver are built in (BH76330FVM, BH76331FVM)

9) Enables two load drivers [when using output coupling capacitor] (BH76330FVM, BH76331FVM)

10) Able to be used without output coupling capacitor (BH76330FVM)

11) MSOP8 compact package

Applications

Input switching in car navigation systems, TVs, DVD systems, etc.

Line-up

BH76330FVM BH76331FVM BH76332FVM BH76333FVM

Supply voltage 2.8 V to 5.5 V

Amp gain 6 dB -0.1 dB

Video driver Included －

Frequency response 100 kHz/10 MHz, 0 dB (Typ.) 100 kHz/30 MHz, 0 dB (Typ.)

Input type Sync tip

clamp

Bias

(Zin = 150 k)

Sync tip

clamp

Bias

(Zin = 150 k)

Absolute maximum ratings (Ta = 25)

Parameter Symbol Limits Unit

Supply voltage VCC 7.0 V

Power dissipation Pd 470 ＊1 mW

Input voltage range VIN 0 to VCC+0.2 V

Operating temperature

range Topr

-40 to +85

Storage temperature

range Tstg

-55 to +125

*1 When used while Ta = 25, 4.7 mW is dissipated per 1

Mounted on 70 mm x 70 mm x 1.6 mm glass epoxy board

Operation range (Ta = 25)

Parameter Symbol Min. Typ. Max Unit

Supply voltage VCC 2.8 5.0 5.5 V




Electrical characteristics 1 (unless otherwise specified, Ta = 25, VCC = 5 V)

Parameter Symbol Typ.

Unit Conditions 76330 76331 76332 76333

Circuit current 1 ICC1 10 9 mA When no signal Circuit current 2 ICC2 0.0 µA During standby

Circuit current 3 ICC3-1 11 10

mADuring output of color bar signal

ICC3-2 17 － During output of color bar signal (no C in output)

Maximum output level VOM 4.6 3.8 3.4 Vpp f = 10 kHz, THD = 1% Voltage gain GV 6.0 -0.1 dB Vin = 1.0 Vpp, f = 100 kHz

Frequency response GF1 0 － dB Vin = 1.0 Vpp, f = 10 MHz/100 kHz GF2 － 0 dB Vin = 1.0 Vpp, f = 30 MHz/100 kHz

Crosstalk between channels

CT -65 dB Vin = 1.0 Vpp, f = 4.43 MHz

Mute attenuation MT -65 dB Vin = 1.0 Vpp, f = 4.43 MHz

CTL pin switch level VTHH 1.2 Min V High level threshold voltage VTHL 0.45 Max V Low level threshold voltage

CTL pin inflow current ITHH 50 Max µA CTL pin = 2.0 V applied Input impedance Zin － 150 － 150 k Differential gain DG 0.3 % Vin = 1.0 Vpp

Standard stair step signal Differential phase

DP-1 0.7 0.3 deg.

DP-2 0.0 － Same condition as above (no C in output)

Y-related S/N SNY +75 +78 dBVin = 1.0 Vpp, bandwidth: 100 k to 6 MHz

100% white video signal C-related S/N [AM] SNCA +75

dBVin = 1.0 Vpp, bandwidth: 100 to 500 kHz

100% chroma voltage signal C-related S/N [PM] SNCP +65 Electrical characteristics 2 (unless otherwise specified, Ta = 25, VCC = 3 V)


Unit Conditions 76330 76331 76332 76333

Circuit current 1 ICC1 8.5 8.0 mA When no signal Circuit current 2 ICC2 0.0 µA During standby

Circuit current 3 ICC3-1 9.5 9.0 mA During output of color bar signal

ICC3-2 15.5 － During output of color bar signal (no C in output)

Maximum output level VOM 2.7 2.8 1.8 1.9 Vpp f = 10 kHz, THD = 1% Voltage gain GV 6.0 -0.1 dB Vin = 1.0 Vpp, f = 100 kHz

Frequency response GF1 0 － dB Vin = 1.0 Vpp, f = 10 MHz/100 kHz GF2 － 0 dB Vin = 1.0 Vpp, f = 30 MHz/100 kHz


CT -65 dB Vin = 1.0 Vpp, f = 4.43 MHz

Mute attenuation MT -65 dB Vin = 1.0 Vpp, f = 4.43 MHz

CTL pin switch level VTHH 1.2 Min V High level threshold voltage VTHL 0.45 Max V Low level threshold voltage

CTL pin inflow current ITHH 50 Max µA CTL pin = 2.0 V applied Input impedance Zin － 150 150 k Differential gain DG 0.3 0.7 0.3 % Vin = 1.0 Vpp


DP-1 1.0 0.3 deg.



100% white video signal C-related S/N [AM] SNCA +75 dB Vin = 1.0 Vpp, bandwidth: 100 to 500 kHz

100% chroma video signal C-related S/N [PM] SNCP +65 dB(Note) Re: ICC3, VOM, GV, GF, CT, MT, DG, DP, SNY, SNCA, and SNCP parameters

BH76330FVM and BH76331FVM: RL = 150 BH76332FVM and BH76333FVM: RL = 10 k




Control pin settings

CTL

A B STBY L(OPEN) L(OPEN)IN1 L(OPEN) H IN2 H L(OPEN)IN3 H H

Block diagram

Fig.1 BH76330FV Fig.2 BH76331FV

Fig. 3 BH76332FV Fig. 4 BH76333FV

IN1

CTLA

IN2

GND

OUT

1

2

3 6

7

8

VCC

4 5

CTLB IN3 logic

Sync_Tip

Clamp

Sync_Tip

Clamp

75Ω 6dB

Sync_Tip

Clamp

IN1

CTLA

IN2

GND

OUT

1

2

3 6

7

8

VCC

4 5

CTLB IN3 logic

75Ω6dB

BIAS

BIAS

BIAS

IN1

CTLA

IN2

GND

OUT

1

2

3 6

7

8

VCC

4 5

CTLB IN3 logic

Sync_Tip

Clamp

Sync_Tip

Clamp

Sync_Tip

Clamp

0dB

BIAS

IN1

CTLA

IN2

GND

OUT

1

2

3 6

7

8

VCC

4 5

CTLB IN3 logic

0dB

BIAS

BIAS




I/O equivalent circuit diagrams

Input pins

Note 1) The above DC potential is only when VCC = 5 V. This value is a reference value and is not guaranteed.

Note 2) Numerical values shown in these figures are design values, and compliance to standards is not guaranteed.

Sync tip clamp input

BH76330FVM/BH76332FVM Bias input

BH76331FVM/BH76333FVM Pin No. Name Equivalent circuit Pin No. Name Equivalent circuit

1 3 5

IN1 IN2 IN3

1 3 5

IN1 IN2 IN3

Video signal input pin is used for sync tip clamp input.

・DC potential

BH76330FVM: 1.5 V BH76332FVM: 1.0 V

Video signal input pin is used for bias type input. Input

impedance is 150 k.

・DC potential

BH76331FVM: 3.1 V BH76333FVM: 2.5 V

Control pins

Pin No. Name Equivalent circuit

2

4

CTLA

CTLB

Switches operation mode [active or standby] and input

pin.

Threshold level is 0.45 V to 1.2 V.

Output pin

With video driver

BH76330FVM/BH76331FVM Without video driver

BH76332FVM/BH76333FVM Pin No. Name Equivalent circuit Pin No. Name

7 OUT

7 OUT

Video signal output pin. Able to drive loads up to 75

(dual drive).

・DC potential

BH76330FVM: 0.16 V BH76331FVM: 2.5 V

Video signal output pin.

・DC potential

BH76332FVM: 0.3 V BH76333FVM: 1.8 V

IN 100Ω

CTL 50kΩ

250kΩ

200kΩ

200kΩ

OUT

14kΩ

OUT

3.0mA

IN100Ω

150kΩ




Test Circuit Diagrams

Application circuit examples

See pages 6/16 to 10/16 for description of how to determine the capacity of I/O coupling capacitors.

Fig. 5 BH76330FV/BH76331FV Test Circuit Diagram



Test circuit diagrams are used for shipment inspections, and differ from application circuits.

Fig. 6 BH76332FV/BH76333FV Test Circuit Diagram

0.01μF

10μF

A

VCC

0.01μF

50Ω

A

0.01μF

50Ω

A

0.01μF 50Ω

75Ω

V V75Ω10μF

IN1

CTLA

IN2

GND

OUT

1

2

3 6

7

8

VCC

4 5

CTLB IN3 logic

Sync_Tip

Clamp

Sync_Tip

Clamp

75Ω 6dB

Sync_Tip

Clamp

10μF V V10kΩ

0.01μF

10μF

A

VCC

0.01μF

50Ω

A

0.01μF

50Ω

A

0.01μF 50Ω

IN1

CTLA

IN2

GND

OUT

1

2

3 6

7

8

VCC

4 5

CTLB IN3 logic

Sync_Tip

Clamp

Sync_Tip

Clamp

Sync_Tip

Clamp

0dB

IN1

CTLA

IN2

GND

OUT

1

2

3 6

7

8

VCC

4 5

CTLB IN3 logic

Sync_Tip

Clamp

Sync_Tip

Clamp

Sync_Tip

Clamp

0dB

VIDEO_IN

0.1μF

VIDEO_IN

0.1μF

VIDEO_IN

0.1μF

0.1μF

47μF VCC

VIDEO_OUT

VIDEO_IN

VIDEO_IN

4.7μF

4.7μF

BIAS

IN1

CTLA

IN2

GND

OUT

1

2

3 6

7

8

VCC

4 5

CTLB IN3 logic

0dB

BIAS

BIAS

VIDEO_IN

4.7μF

0.1μF

47μF VCC

VIDEO_OUT

0.1μF

470μF 75Ω

VIDEO_OUT

VIDEO_IN

VIDEO_IN

0.1μF

0.1μF

VIDEO_IN

0.1μF

47μF VCC

IN1

CTLA

IN2

GND

OUT

1

2

3 6

7

8

VCC

4 5

CTLB IN3 logic

Sync_Tip

Clamp

Sync_Tip

Clamp

75Ω 6dB

Sync_Tip

Clamp

75Ω

VIDEO_OUT7

When used without output capacitor

0.1μF

470μF 75Ω

VIDEO_OUT

VIDEO_IN

4.7μF

47μF VCC

IN1

CTLA

IN2

GND

OUT

1

2

3 6

7

8

VCC

4 5

CTLB IN3 logic

75Ω 6dB

BIAS

BIAS

BIAS

VIDEO_IN

4.7μF

VIDEO_IN

4.7μF




Cautions for selection and use of application parts

When using this IC by itself ①

Input type Input impedance

Zin

Capacity of input coupling

capacitor (recommended

value)

Capacity of output coupling

capacitor (recommended

value)

Sync_Tip_Clamp 10 M 0.1 µF 470 µF to 1000 µF

Bias 150 k 4.7 µF

Method for determining capacity of input coupling capacitor

The HPF is comprised of an input coupling capacitor and the internal input impedance Zin of the IC. Since the fc value of this HPF is

determined using the following equation (a), the above recommended capacity for the input capacitor is derived. Usually, the cutoff

frequency fc is several Hz.

fc = 1 / (2π × C × Zin)・・・・(a)

When evaluating the sag characteristics and determining the capacity of the capacitor during video signal input, a horizontal stripe signal

called "H bar" (shown in Fig. 10) is suitable, and this type of signal is used instead of a color bar signal to evaluate characteristics and

determine capacity.

Method for determining capacity of output coupling capacitor

The output pins of models with a 75 driver [BH76330FVM and BH76331FVM] have an HPF comprised of an output coupling capacitor and

load resistance RL (= 150). When fc is set to approximately 1 Hz or 2 Hz, the capacity of the output coupling capacitor needs to be

approximately 470 µF to 1000 µF.

As for models without the 75 driver, an HPF is similarly comprised using the capacity of the output coupling capacitor and the input

impedance of the IC connected at the next stage, and the capacitance required for the output coupling capacitor should be estimated using

equation (a).

When this IC is used as a standalone device ②

In models that include a 75 driver [BH76330FVM and BH76331FVM], up to two monitors (loads) can be connected (a connection example

is shown in Fig. 12). When there are multiple loads, the number of output coupling capacitors must be increased or a larger capacitance

must be used, based on the table shown below.

Application circuit example No. of output capacitors Capacitance per output capacitor (recommended values)

Fig. 12 (a) No. of drives required 470 µF to 1000 µF (same as with one drive)

Fig. 12 (b) 1 (No. of drive × 470 µF to 1000) uF

When this IC is used as a standalone device ③

The BH76330FVM is the only model that can be used without an output coupling capacitor.

This use method not only enables reductions in board space and part-related costs, but it is able to improve the sag characteristics by

improving low-range frequency response. However, when the output coupling capacitor is omitted, a direct current flows to the connected

set, so the specifications of the connected set should be noted carefully before starting use.

Note also that only one load can be connected when the output coupling capacitor is omitted.

Fig.11 Example of Screen with Obvious Sag (H-bar Signal)

7 OUT

470μF

75Ω

75Ω

470μF

75Ω

75Ω

monitor

monitor

7OUT

(470×2)μF

75Ω

75Ω

75Ω

75Ω

monitor

monitor

Fig. 12 (a) Application Circuit Example 1 (Two Drives) Fig. 12 (b) Application Circuit Example 2 (Two Drives)

7OUT

75Ω

75Ω

monitor

BH76330FV

Fig.13 Application Example without Output Coupling Capacitor

Voltage at output ≒0.16V 0 2VWhen this voltage load resistance is applied,

a direct current is generated.




When using several of these ICs ①

When several of these ICs are used, it enables applications in which separate images are output to the car navigation system's front and rear monitors.

When several ICs are used at the same time, the number of parallel connections of input impedance equals the number of ICs being used, which reduces the input impedance. This also raises the fc value of the HPF formed at the input pin block, so the capacitance of the input coupling capacitor must be increased according to equation (a). The recommended values for calculation results are listed in the table below. When a clamp is used as the input type, the original input impedance becomes much greater, and if two or three are used at the same time there is no need to change the capacitance of the input coupling capacitor.

Input type Input impedance per ICNumber of ICs

used Total

input impedance

Capacitance of input coupling capacitor

(recommended values)

Sync_Tip_Clamp Approx. 10 M2 Approx. 5 M 0.1 µF

3 Approx. 3 M 0.1 µF

Bias 150 k 2 75 k 6.8 µF~

3 50 k 10 µF~

When using several of these ICs ②

When three bias input type models (BH76331FVM or BH76333FVM) are used in parallel, they can be used for RGB signal switching applications. Likewise, when one clamp input type model (BH76330FVM or BH76332FVM) is connected in parallel with two bias input type models (a total of three ICs used in parallel), they can be used for component signal switching applications. The same method can be used to determine the capacitance of I/O coupling capacitors of these applications.

7

1

IN1

OUT

Clamp /Bias

470μF

75Ω

75Ω

Front monitor

3

IN2

Clamp /Bias

5

IN3

Clamp /Bias

1

IN1

Clamp /Bias

3

IN2

Clamp /Bias

5

IN3

Clamp /Bias

VIDEO IN

VIDEO IN

VIDEO IN

7OUT

470μF

75Ω

75Ω

Rear monitor

Fig.14 Application Example when Using Several ICs

7

1

IN1

OUT

Bias

3

IN2

Bias

5

IN3

Bias

7

1

IN1

OUT

Bias

3

IN2

Bias

5

IN3

Bias

VIDEO IN[R1]

7

1

IN1

OUT

Bias

3

IN2

Bias

5

IN3

Bias

VIDEO IN[R2]

VIDEO IN[R3]

VIDEO IN[G1]

VIDEO IN[G2]

VIDEO IN[G3]

VIDEO IN[B1]

VIDEO IN[B2]

VIDEO IN[B3]

R_OUT

G_OUT

B_OUT

SW select

BH76331FV

or BH76333FV

BH76331FV

or BH76333FV

BH76331FV

or BH76333FV

4.7μF

4.7μF

4.7μF

4.7μF

4.7μF

4.7μF

4.7μF

4.7μF

4.7μF

7

1

IN1

OUT

Clamp

3

IN2

Clamp

5

IN3

Clamp

7

1

IN1

OUT

Bias

3

IN2

Bias

5

IN3

Bias

VIDEO IN[Py1]

7

1

IN1

OUT

Bias

3

IN2

Bias

5

IN3

Bias

VIDEO IN[Py2]

VIDEO IN[Py3]

VIDEO IN[Pb1]

VIDEO IN[Pb2]

VIDEO IN[Pb3]

VIDEO IN[Pr1]

VIDEO IN[Pr2]

VIDEO IN[Pr3]

Py_OUT

Pb_OUT

Pr_OUT

SW select

BH76330FV

or BH76332FV

BH76331FV

or BH76333FV

BH76331FV

or BH76333FV

0.1uF

0.1uF

0.1uF

4.7uF

4.7uF

4.7uF

4.7uF

4.7uF

4.7uF

Fig. 15 (a). RGB Signal Switching Application Example (using three bias input type models in parallel)

Fig. 15 (b). Component Signal Switching Application Example(using one clamp input type model and two bias input type models in parallel)




Cautions for use

1. The numerical values and data shown here are typical design values, not guaranteed values.

2. The application circuit examples show recommended circuits, but characteristics should be checked carefully before using

these circuits. If any external part constants are modified before use, factors such as variation in all external parts and

ROHM LSI ICs, including not only static characteristics but also transient characteristics, should be fully considered to set

an ample margin.

3. Absolute maximum ratings

If the absolute maximum ratings for applied voltage and/or operation temperature are exceeded, LSI damage may result.

Therefore, do not apply voltage or use in a temperature that exceeds these absolute maximum ratings. If it is possible that

absolute maximum ratings will be exceeded, use a physical safety device such as a fuse and make sure that no conditions

that might exceed the absolute maximum ratings will be applied to the LSI IC.

4. GND potential

Regardless of the operation mode, the voltage of the GND pin should be at least the minimum voltage. Actually check

whether or not the voltage at each pin, including transient phenomena, is less than the GND pin voltage.

5. Thermal design

The thermal design should be done using an ample margin that takes into consideration the allowable dissipation under

actual use conditions.

6. Shorts between pins and mounting errors

When mounting LSI ICs onto the circuit board, make sure each LSI's orientation and position is correct. The ICs may

become damaged if they are not mounted correctly when the power is turned on. Similarly, damage may also result if a

short occurs, such as when a foreign object is positioned between pins in an IC, or between a pin and a power supply or

GND connection.

7. Operation in strong electromagnetic field

When used within a strong electromagnetic field, evaluate carefully to avoid the risk of operation faults.

8. Place the power supply's decoupling capacitor as close as possible to the VCC pin (PIN 6) and GND pin (PIN 8).

9. With a clamp input type model (BH76330FVM or BH76332FVM), if any unused input pins are left open they will oscillate, so

unused input pins should instead be connected to GND via a capacitor or else directly connected to VCC.

10. With models that do not include a 75driver (BH76332FVM or BH76333FVM), in some cases the capacitance added to the

set board may cause the peak frequency response to occur at a high frequency. To lower the peak frequency, connect in

series resistors having resistance of several dozen to several hundred as close as possible to the output pin.

11. Frequency response in models that do not include a 75- driver (BH76332FVM and BH76333FVM) was measured as 100

kH/30 MHz: 0 dB (Typ.) in the application circuit examples (shown in Fig. 9 and Fig. 10), and when resistance of about 1 or 2 k is applied from the IC's output pin to GND, this frequency response can be improved (the lower limit of the applied resistance should be 1 k). In such cases, gain is reduced, since the output voltage is divided by the added resistance and the output resistance of the IC.

7OUT

Resistors (several dozen Ω toseveral hundredΩ) to lower peakfrequency

Output pin

Fig.16 Positions where Resistors are Inserted to Lower Peak Frequency Response in BH76332FV or BH76333FV

-7

-6

-5

-4

-3

-2

-1

0

1

1M 10M 100M 1000M

Frequency [Hz]

Voltag

e g

ain [

dB

]

(c) Voltage gain fluctuation when resistance is inserted [f = 100 kHz]

(Voltage gain without inserted resistance: -0.11 dB)

7 OUT

Resistance to improve frequencyresponse (R: 1-2 kΩ)

3mA

Fig.17 Result of Resistance Inserted to Improve BH76332FVM/BH76333FVM Frequency Response

(a) Resistor insertion points (b) Frequency response changes when resistance is inserted

Input amplitude: 1 Vpp, Output load resistance: 10 kΩ Other constants are as in application examples (Figs. 9 & 10)

-0.20

-0.18

-0.16

-0.14

-0.12

-0.10

0.5 1 1.5 2 2.5

出力端子付加抵抗値[kΩ]

GA

IN@

f=100kH

z[dB

]

R=1kΩ

R=2kΩ

No resistance

Resistance added to output pin [k]




12. With clamp input type models (BH76330FVM and BH76332FVM), if the termination impedance of the video input pin becomes higher, sync contractions or oscillation-related problems may occur. Evaluate temperature and other characteristics carefully and use at 1 k or less.

Evaluation board pattern diagram and circuit diagram

Parts list

Symbol Function Recommended value Comments

R1 R3 R5 Input terminating resistor 75 －

C1 C3 C5 Input coupling

capacitor See pages 6/16 to 7/16 to determine B characteristics recommended

R71 Output resistor 75 －

C7 Output coupling


C01 Decoupling capacitor

10 µF B characteristics recommended

C02 0.1 µF

Fig. 19. Evaluation Board Circuit Diagram

Fig. 20. Evaluation Board Pattern Diagram

0

1

2

3

4

5

6

0 1k 2k 3k

入力終端抵抗Rin[Ω]

入力

端子

での

sync縮

み量

[%]

Fig. 18. Relation between Input Pin Termination Impedance and Amount of Sync Contraction

Am

ou

nt o

f sy

nc

con

trac

tion

at

inpu

t pin

[%

]

Input termination resistance Rin [Ω]




Reference data (1) BH76330FVM/BH76331FVM [unless otherwise specified, output capacitance C: 470 µF, RL = 150

-2.0

-1.5

-1.0

-0.5

0.0

0.5

1.0

2 3 4 5 6

電源電圧[V]

周波

数特

性(1

00k/1

0MH

z)[d

B]

-2.0

-1.5

-1.0

-0.5

0.0

0.5

1.0

-50 0 50 100

周囲温度[]

周波

数特

性(1

00k/10M

Hz)[

dB]

5.7

5.8

5.9

6.0

6.1

6.2

6.3

-50 0 50 100

周囲温度[]

電圧

利得

[dB

]

5.7

5.8

5.9

6.0

6.1

6.2

6.3

2 3 4 5 6

電源電圧[V]

電圧

利得

[dB

]

5.7

5.8

5.9

6.0

6.1

6.2

6.3

-50 0 50 100

周囲温度[]

電圧

利得

[dB

]

5.7

5.8

5.9

6.0

6.1

6.2

6.3

2 3 4 5 6

電源電圧[V]

電圧

利得

[dB

]

2.0

3.0

4.0

5.0

6.0

2 3 4 5 6

電源電圧[V]

最大

出力

レベ

ル[V

pp]

2.0

2.2

2.4

2.6

2.8

3.0

-50 0 50 100

周囲温度[]

最大

出力

レベ

ル[V

pp]

2.0

2.2

2.4

2.6

2.8

3.0

-50 0 50 100

周囲温度[]

最大

出力

レベ

ル[V

pp]

2.0

3.0

4.0

5.0

6.0

2 3 4 5 6

電源電圧[V]

最大

出力

レベ

ル[V

pp]

-0.5

0.0

0.5

1.0

1.5

2.0

-50 0 50 100

周囲温度[]

回路

電流

（S

TB

Y)[

μA

]

-0.5

0.0

0.5

1.0

1.5

2.0

2 3 4 5 6

電源電圧[V]

回路

電流

(ST

BY

)[μ

A]

Fig. 21 ICC1 vs. Supply Voltage Fig. 22 ICC1 vs. Ambient Temperature

Fig.26 ICC2 vs. Ambient Temperature

Ta=25

VCC=5V

Fig.29 Vom vs. Supply Voltage Fig.30 Vom vs. Ambient Temperature Fig.31 GV vs. Supply Voltage Fig.32 GV vs. Ambient Temperature

Fig.35 GF vs. Supply Voltage Fig.36 GF vs. Ambient Temperature

Fig.25 ICC2 vs. Supply Voltage

Ta=25

BH76330/31FV

BH76330FV

VCC=5V

Fig. 23 ICC1 vs. Supply Voltage Fig.24 ICC1 vs. Ambient Temperature

BH76330/31FV

BH76330FV

BH76360FV

Ta=25

VCC=3V

Ta=25

VCC=5V

Fig.27 Vom vs. Supply Voltage Fig.28 Vom vs. Ambient Temperature

Fig.33 GV vs. Supply Voltage Fig.34 GV vs. Ambient Temperature

BH76330FV

BH76330FV

Ta=25

VCC=5V

BH76330FV

BH76330FV

BH76330FV

Ta=25

BH76331FV

VCC=5V

BH76331FV

Ta=25

BH76331FV

BH76331FV

VCC=3V

Ta=25

BH76331FV

BH76331FV

VCC=5V

0

5

10

15

20

2 3 4 5 6

電源電圧[V]

回路

電流

[mA]

出力C容量：470uF

出力Cレス

0

5

10

15

20

-50 0 50 100

周囲温度[]

回路

電流

[mA]

0

5

10

15

20

2 3 4 5 6

電源電圧[V]

回路

電流

[mA]

0

5

10

15

20

-50 0 50 100

周囲温度[]

回路

電流

[mA]

Circ

uit

curr

en

t [m

A]

Supply Voltage [V]

Circ

uit

curr

en

t [m

A]

Circ

uit

curr

en

t [m

A]

Circ

uit

curr

en

t [m

A]

Supply Voltage [V]Ambient Temperature [] Ambient Temperature []

Ambient Temperature []

Circ

uit

curr

en

t (S

TB

Y)

[μA

]

Ma

xim

um

ou

tpu

t le

vel [

Vpp

]

Circ

uit

curr

en

t (S

TB

Y)

[μA

]

Ma

xim

um

ou

tpu

t le

vel [

Vpp

]

Supply Voltage [V] Ambient Temperature []

Vo

ltage

ga

in [d

B]

Vo

ltage

ga

in [d

B]

Ma

xim

um

ou

tpu

t le

vel [

Vpp

]

Ma

xim

um

ou

tpu

t le

vel [

Vpp

]

Supply Voltage [V] Ambient Temperature [] Supply Voltage [V] Ambient Temperature []


Vo

ltage

ga

in [d

B]

Vo

ltage

ga

in [d

B]

Fre

quen

cy r

espo

nse

(100

kH

z/10

MH

z) [

dB]

Fre

quen

cy r

esp

onse

(10

0 kH

z/10

MH

z) [

dB]

Output capacitance C: 470 µF

No output capacitance

Supply Voltage [V]




BH76330FV

BH76330/31FV

0

10

20

30

40

50

60

70

-50 0 50 100周囲温度[]

CT

L端子

流入

電流

[uA

]

0

5

10

15

20

0 0.5 1 1.5 2

CTL_D端子電圧

回路

電流

[mA

]

-75

-73

-71

-69

-67

-65

-50 0 50 100

周囲温度[]

チャ

ンネ

ル間

クロ

スト

ーク

(wor

st)

[dB

]

-75

-73

-71

-69

-67

-65

2 3 4 5 6

電源電圧[V]

チャ

ンネ

ル間

クロ

スト

ーク

(wors

t)[d

B]

-80

-78

-76

-74

-72

-70

-50 0 50 100

周囲温度[]

ミュ

ート

減衰

量(w

ors

t)[d

B]

-80

-78

-76

-74

-72

-70

2 3 4 5 6

電源電圧[V]

ミュ

ート

減衰

量(w

orst

)[dB

]

-15

-10

-5

0

5

1M 10M 100M

Frequency[Hz]

Gai

n[d

B]

-15

-10

-5

0

5

1M 10M 100M

Frequency[Hz]

Gai

n[d

B]

-2.0

-1.5

-1.0

-0.5

0.0

0.5

1.0

2 3 4 5 6

電源電圧[V]

周波

数特

性(1

00k/1

0MH

z)[d

B]

-2.0

-1.5

-1.0

-0.5

0.0

0.5

1.0

-50 0 50 100

周囲温度[]

周波

数特

性(1

00k/10M

Hz)[

dB]

Fig.41 CT(worst) vs. Supply Voltage

Fig.42 CT(worst) vs. Ambient Temperature Fig.43 MT(worst) vs. Supply Voltage Fig.44 MT(wrost) vs. Ambient Temperature

Ta=25

VCC=5V, Ta=25

Fig. 45 CTLb pin voltage vs Circuit Current (CLT threshold )

Fig.46 ITHH vs. Ambient Temperature (Voltage applied to CTL pin = 2V)

Fig.47 DG vs. Supply Voltage Fig.48 DG vs. Ambient Temperature

Fig.52 DP vs. Ambient Temperature


Fig. 39 Frequency Response Fig. 40 Frequency Response

BH76330/31FV

BH76331FV

VCC=5V

BH76330/31FV

VCC=5V Ta=25

BH76330/31FV

VCC=5V

BH76330FV

VCC=5V, Ta=25

BH76330/31FV

VCC=5V BH76330/31FV

Ta=25

BH76330FV

VCC=5V


BH76331FV

BH76331FV

Fig.51 DP vs. Supply Voltage

Ta=25

BH76330FV

VCC=5V BH76330FV

Ta=25

BH76331FV

VCC=5V, Ta=25

BH76331FV

Ta=25

VCC=5V

0.0

0.5

1.0

1.5

2.0

2 3 4 5 6電源電圧[V]

微分

利得

[%]

0.0

0.5

1.0

1.5

2.0

-50 0 50 100電源電圧[V]

微分

利得

[%]

0.0

0.5

1.0

1.5

2.0

2 3 4 5 6電源電圧[V]

微分

利得

[%]

0.0

0.5

1.0

1.5

2.0

-50 0 50 100電源電圧[V]

微分

利得

[%]

0.0

0.5

1.0

1.5

2.0

2 3 4 5 6電源電圧[V]

微分

位相

[deg.]


出力Cレス

0.0

0.5

1.0

1.5

2.0

-50 0 50 100電源電圧[V]

微分

位相

[deg

.]


出力Cレス

Fre

quen

cy r

esp

onse

(1

00 k

Hz/

10 M

Hz)

[dB

]

Fre

quen

cy r

esp

onse

(1

00 k

Hz/

10 M

Hz)

[dB

]

Supply Voltage [V]

Supply Voltage [V]




Cro

ssta

lk b

etw

een

chan

nels

(w

orst

) [d

B]

Cro

ssta

lk b

etw

een

chan

nels

(w

orst

) [d

B]

Mu

te a

tten

uat

ion

(w

ors

t) [

dB

]

Mu

te a

tten

uat

ion

(w

ors

t) [

dB

]

Circ

uit

curr

en

t [m

A]

CT

L p

in in

flux

curr

en

t [µ

A]

Diff

ere

ntia

l ga

in [%

]

Diff

ere

ntia

l ga

in [%

]

CTL_B pin voltage [V] Ambient Temperature [] Supply Voltage [V] Ambient Temperature []

Diff

ere

ntia

l ga

in [%

]

Diff

ere

ntia

l ga

in [%

]

Diff

ere

ntia

l ph

ase

[de

g.]

Diff

ere

ntia

l ph

ase

[de

g.] Output capacitance C: 470 µF





CTL_A：0[V]




Reference data (2) BH76332FVM/BH76333FVM [unless otherwise specified, output capacitance C: 470 µF, RL = 10 k]

70

72

74

76

78

80

2 3 4 5 6

電源電圧[V]

C系

S/N

(AM

)[dB

]

70

72

74

76

78

80

-50 0 50 100

周囲温度[]

C系

S/N

(AM

)[dB

]

65

66

67

68

69

70

2 3 4 5 6

電源電圧[V]

C系

S/N

(PM

)[dB

]

65

66

67

68

69

70

-50 0 50 100周囲温度[]

C系

S/N

(PM

)[dB

]

70

72

74

76

78

80

2 3 4 5 6

電源電圧[V]

Y系

S/N

[dB

]

70

72

74

76

78

80

-50 0 50 100

周囲温度[]

Y系

S/N

[dB

]

Ta=25

VCC=5V

BH76331FV

Fig.57 SNCA vs. Supply Voltage

Fig.58 SNCA vs. Ambient Temperature Fig.59 SNCP vs. Supply Voltage Fig.60 SNCP vs. Ambient Temperature


Fig.54 DP vs. Ambient Temperature

BH76331FV

BH76330/31FV

Fig.55 SNY vs. Supply Voltage Fig.56 SNY vs. Ambient Temperature

BH76330/31FV

Ta=25

VCC=5V

BH76330/31FV

BH76330/31FV

Ta=25

VCC=5V

BH76330/31FV

BH76330/31FV

Ta=25

VCC=5V

0.0

0.5

1.0

1.5

2.0

2 3 4 5 6電源電圧[V]

微分

位相

[deg.

]

0.0

0.5

1.0

1.5

2.0

-50 0 50 100電源電圧[V]

微分

位相

[deg

.]

Diff

ere

ntia

l ph

ase

[de

g.]

Diff

ere

ntia

l ph

ase

[de

g.]


C S

/N (

AM

) [d

B]

C S

/N (

AM

) [d

B]

C S

/N (

PM

) [d

B]

C S

/N (

PM

) [d

B]


Y S

/N [

dB]

Y S

/N [

dB]

1.5

1.7

1.9

2.1

2.3

2.5

-50 0 50 100

周囲温度[]

最大

出力

レベ

ル[V

pp]

BH76332/33FV

1.0

2.0

3.0

4.0

5.0

2 3 4 5 6

電源電圧[V]

最大

出力

レベ

ル[V

pp]

Fig.61 ICC1 vs. Supply Voltage Fig.62 ICC1 vs. Ambient Temperature

Fig.66 ICC2 vs. Ambient Temperature Fig.65 ICC2 vs. Supply Voltage



-0.5

0.0

0.5

1.0

1.5

2.0

2 3 4 5 6

電源電圧[V]

回路

電流

(ST

BY

)[μ

A]

-0.5

0.0

0.5

1.0

1.5

2.0

-50 0 50 100

周囲温度[]

回路

電流

（ST

BY

)[μ

A]

BH76332FV

BH76332FV

Ta=25

VCC=5V

BH76333FV

BH76333FV

Ta=25

VCC=5V

Ta=25

VCC=5V

BH76332/33FV

BH76332FV

BH76332FV

Ta=25

VCC=3V

0

5

10

15

20

2 3 4 5 6

電源電圧[V]

回路

電流

[mA

]

0

5

10

15

20

-50 0 50 100

周囲温度[]

回路

電流

[mA]

0

5

10

15

20

2 3 4 5 6

電源電圧[V]

回路

電流

[mA]

0

5

10

15

20

-50 0 50 100

周囲温度[]

回路

電流

[mA]


Circ

uit

curr

en

t [m

A]

Circ

uit

curr

en

t [m

A]

Circ

uit

curr

en

t [m

A]

Circ

uit

curr

en

t [m

A]


Circ

uit

curr

en

t (S

TB

Y)

[μA

]

Circ

uit

curr

en

t (S

TB

Y)

[μA

]

Ma

xim

um

ou

tpu

t le

vel [

Vpp

]

Ma

xim

um

ou

tpu

t le

vel [

Vpp

]




-5

-4

-3

-2

-1

0

1

2

1M 10M 100MFrequency[Hz]

Gai

n[d

B]

-2.0

-1.5

-1.0

-0.5

0.0

0.5

1.0

2 3 4 5 6

電源電圧[V]

周波

数特

性(1

00k/

30M

Hz)[

dB]

-2.0

-1.5

-1.0

-0.5

0.0

0.5

1.0

-50 0 50 100

周囲温度[]

周波

数特

性(1

00

k/30M

Hz)

[dB

]

-5

-4

-3

-2

-1

0

1

2


Gai

n[d

B]

-2.0

-1.5

-1.0

-0.5

0.0

0.5

1.0

2 3 4 5 6

電源電圧[V]

周波

数特

性(1

00k/3

0M

Hz)[

dB

]

-2.0

-1.5

-1.0

-0.5

0.0

0.5

1.0

-50 0 50 100

周囲温度[]

周波

数特

性(1

00k/

30M

Hz)

[dB

]

-0.6

-0.4

-0.2

0.0

0.2

0.4

2 3 4 5 6

電源電圧[V]

電圧

利得

[dB

]

-0.6

-0.4

-0.2

0.0

0.2

0.4

-50 0 50 100

周囲温度[]

電圧

利得

[dB

]1.5

1.7

1.9

2.1

2.3

2.5

-50 0 50 100

周囲温度[]

最大

出力

レベ

ル[V

pp]

1.0

2.0

3.0

4.0

5.0

2 3 4 5 6

電源電圧[V]

最大

出力

レベ

ル[V

pp]

-0.6

-0.4

-0.2

0.0

0.2

0.4

2 3 4 5 6

電源電圧[V]

電圧

利得

[dB

]

-0.6

-0.4

-0.2

0.0

0.2

0.4

-50 0 50 100

周囲温度[]

電圧

利得

[dB

]



Ta=25

VCC=5V

Fig.73 GV vs. Supply Voltage Fig.74 GV vs. Ambient Temperature

BH76332FV

BH76332FV

Ta=25

BH76333FV

BH76333FV

VCC=3V



Fig.77 GF vs. Supply Voltage Fig.78 GF vs. Ambient Temperature Fig. 79 Frequency Response Fig. 80 Frequency Response

Ta=25

BH76333FV

BH76333FV

VCC=5V

Ta=25

VCC=5V

BH76332FV

BH76332FV

Ta=25

BH76333FV

BH76333FV

VCC=5V

VCC=5V ,Ta=25

BH76333FV

BH76332FV

VCC=5V ,Ta=25

-75

-73

-71

-69

-67

-65

-50 0 50 100

周囲温度[]

チャ

ンネ

ル間

クロ

スト

ーク

(wor

st)

[dB

]

-75

-73

-71

-69

-67

-65

2 3 4 5 6

電源電圧[V]

チャ

ンネ

ル間

クロ

スト

ーク

(wors

t)[d

B]

-80

-78

-76

-74

-72

-70

-50 0 50 100

周囲温度[]

ミュ

ート

減衰

量(w

ors

t)[d

B]

-80

-78

-76

-74

-72

-70

2 3 4 5 6

電源電圧[V]

ミュ

ート

減衰

量(w

orst)

[dB

]

BH76332/33FV

Ta=25

VCC=5V

BH76332/33FV

BH76332/33FV

Ta=25

VCC=5V

BH76332/33FV

Ma

xim

um

ou

tpu

t le

vel [

Vpp

]

Ma

xim

um

ou

tpu

t le

vel [

Vpp

]

Vo

ltage

ga

in [d

B]

Vo

ltage

ga

in [d

B]



Vo

ltage

ga

in [d

B]

Vo

ltage

ga

in [d

B]


Fre

quen

cy r

esp

onse

(10

0 kH

z/10

MH

z) [

dB]

Fre

quen

cy r

esp

onse

(10

0 kH

z/10

MH

z) [

dB]

Fre

quen

cy r

esp

onse

(10

0 kH

z/10

MH

z) [

dB]

Fre

quen

cy r

esp

onse

(10

0 kH

z/10

MH

z) [

dB]


Cro

ssta

lk b

etw

een

cha

nn

els

(w

ors

t) [

dB]

Cro

ssta

lk b

etw

een

cha

nn

els

(w

ors

t) [

dB]

Mu

te a

tten

uat

ion

(w

ors

t) [

dB

]

Mu

te a

tten

uat

ion

(w

ors

t) [

dB

]





70

72

74

76

78

80

2 3 4 5 6

電源電圧[V]

C系

S/N

(AM

)[dB

]

70

72

74

76

78

80

-50 0 50 100

周囲温度[]

C系

S/N

(AM

)[dB

]

65

66

67

68

69

70

2 3 4 5 6

電源電圧[V]

C系

S/N

(PM

)[dB

]

65

66

67

68

69

70

-50 0 50 100周囲温度[]

C系

S/N

(PM

)[dB

]

70

72

74

76

78

80

2 3 4 5 6

電源電圧[V]

Y系

S/N

[dB

]

70

72

74

76

78

80

-50 0 50 100

周囲温度[]

Y系

S/

N[d

B]

Fig.85 CTLb pin voltage vs Circuit Current (CLT threshold )



Fig.92 DP vs. Ambient Temperature Fig.89 DG vs. Supply Voltage Fig.90 DG vs. Ambient Temperature Fig.91 DP vs. Supply Voltage




Fig.94 DP vs. Ambient Temperature Fig.95 SNY vs. Supply Voltage Fig.96 SNY vs. Ambient Temperature

0

10

20

30

40

50

60

70

-50 0 50 100周囲温度[]

CT

L端子

流入

電流

[uA

]

VCC=5V

BH76332/33FV

BH76332FV

Ta=25

VCC=5V

BH76332FV

BH76332FV

Ta=25

VCC=5V

BH76332FV

BH76333FV

Ta=25

BH76333FV

Ta=25

BH76332/33FV

VCC=5V, Ta=25

BH76333FV

VCC=5V

BH76333FV

VCC=5V

BH76332/33FV

Ta=25

VCC=5V

BH76332/33FV

BH76332/33FV

Ta=25

VCC=5V

BH76332/33FV

Ta=25

VCC=5V

0

5

10

15

20

0 0.5 1 1.5 2

CTL_D端子電圧

回路

電流

[mA

]

BH76332/33FV

BH76332/33FV

0.0

0.5

1.0

1.5

2.0

2 3 4 5 6電源電圧[V]

微分

利得

[%]

0.0

0.5

1.0

1.5

2.0

-50 0 50 100電源電圧[V]

微分

利得

[%]

0.0

0.5

1.0

1.5

2.0

2 3 4 5 6電源電圧[V]

微分

利得

[%]

0.0

0.5

1.0

1.5

2.0

-50 0 50 100電源電圧[V]

微分

利得

[%]

0.0

0.5

1.0

1.5

2.0

2 3 4 5 6電源電圧[V]

微分

位相

[deg.]

0.0

0.5

1.0

1.5

2.0

-50 0 50 100電源電圧[V]

微分

位相

[deg.]

0.0

0.5

1.0

1.5

2.0

2 3 4 5 6電源電圧[V]

微分

位相

[deg.]

0.0

0.5

1.0

1.5

2.0

-50 0 50 100電源電圧[V]

微分

位相

[deg

.]

Circ

uit

curr

en

t [m

A]

CTL_B pin voltage [V]

CT

L p

in in

flux

curr

en

t [µ

A]


Supply Voltage [V]

Diff

ere

ntia

l ga

in [%

]

Diff

ere

ntia

l ga

in [%

]




Diff

ere

ntia

l ph

ase

[de

g.]

Diff

ere

ntia

l ph

ase

[de

g.]

Diff

ere

ntia

l ga

in [%

]

Diff

ere

ntia

l ga

in [%

]

Diff

ere

ntia

l ph

ase

[de

g.]

Diff

ere

ntia

l ph

ase

[de

g.]

Y S

/N [

dB]

Y S

/N [

dB]

C S

/N (

AM

) [d

B]

C S

/N (

AM

) [d

B]


C S

/N (

PM

) [d

B]

C S

/N (

PM

) [d

B]


CTL_A：0[V]

Supply Voltage [V]




External dimensions and label codes

Fig. 101 External Dimensions of BH7633xFVM Series Package When used with 6-input, 1-output video switch BH7636xFV

Fig. 14 above shows an application example in which two of these ICs are used. When the similar IC models BH7636xFV and BH7633xFVM are used at the same time, the type of configuration shown below can be combined. In such cases, input coupling capacitors can be used, as in the application example in Fig. 14.

Fig. 102 Application Example in which BH76330FVM and BH76360FV Are Used Concurrently For details of BH7636xFV, see the BH7636xFV Series Application Notes.

MSOP8 (unit: mm )

Lot. No.

7

Model Code

BH76330FV 76330

BH76331FV 76331

BH76332FV 76332

BH76333FV 76333

6 3 3 0

Max 3.25 (include . BURR)

16

2

IIN1

OUT

Clamp

75Ω

75Ω

フロントモニタ

4

IIN2

Clamp

6

IIN3

Clamp

16

1

OUT

Clamp

75Ω

75Ω

リアモニタ

3

Clamp

5

Clamp

外部入力

TV

DVD

※2

BH76360FV

BH76330FVM

8

IIN4

Clamp

9

IIN5

Clamp

11

IIN6

Clamp

ナビ画面

リアカメラ

IIN1

IIN2

IIN3

※3

※1

※2

＊1 Input coupling capacitor can be used with

this. ＊2 Output coupling capacitors can be omitted

when using BH76330FVM or BH76360FV, and this helps reduce the number of parts.

＊3 Any inputs that are not used should be

connected directly to VCC or shorted with GND via a capacitor.

External input

Navigation screen

Rear camera

Front monitor

Rear monitor




Line-up of products with built-in video amplifier and video driver

6-input, 1-output video switch BH76360FV, BH76361FV, BH76362FV, BH76363FV General

BH76360FV, BH76361FV, BH76362FV, and BH76363FV are video signal switching ICs, each with six inputs and one circuit

input, which feature wide dynamic range and frequency response. Since these ICs can be used with low voltage starting at

VCC = 2.8 V, they are applicable not only in stationary devices but also in mobile devices.

This product line-up supports a broad range of input signals, depending on whether or not a 6-dB video amplifier and video

driver are included and what combination of sync tip clamp type and bias (resistor termination) type inputs are used.

Features

1) Able to use a wide range of power supply voltage, from 2.8 V to 5.5 V

2) Wide output dynamic range

3) Excellent frequency response

(BH76360FV, BH76361FV：100kHz/10MHz 0dB[Typ.]、BH76362FV, BH76363FV：100kHz/30MHz 0dB[Typ.])

4) No crosstalk between channels (Typ.-65dB, f=4.43MHz)

5) Built-in mute function (Typ.-65dB, f=4.43MHz)

6) Built-in standby function, circuit current during standby is 0 µA (Typ.)

7) Sync tip clamp input （BH76360FV, BH76362FV）

8) Bias input (Zin=150kΩ) （BH76361FV, BH76363FV）

9) 6-dB amp and 75 driver are built in （BH76360FV, BH76361FV）

10) Enables two load drivers [when using output coupling capacitor]（BH76360FV, BH76361FV）

11) Able to be used without output coupling capacitor (BH76360FV)

12) SSOP-B16 compact package

Applications

Input switching in car navigation systems, TVs, DVD systems, etc.

Line-up

BH76360FV BH76361FV BH76362FV BH76363FV

Supply voltage 2.8 V to 5.5 V

Amp gain 6dB -0.1dB

Video driver Included －

Frequency response 100kHz/10MHz 0dB (Typ.) 100kHz/30MHz 0dB (Typ.)

Input type Sync tip

clamp

Bias

(Zin = 150 k)

Sync tip

clamp

Bias

(Zin = 150 k)

Absolute maximum ratings (Ta = 25)

Parameter Symbol Limits Unit

Supply voltage VCC 7.0 V

Power dissipation Pd 450 ＊1 mW

Input voltage range VIN 0 to VCC+0.2 V

Operating temperature

range Topr

-40 to +85

Storage temperature

range Tstg

-55 to +125

*1 When used while Ta = 25, 4.7 mW is dissipated per 1

Mounted on 70 mm x 70 mm x 1.6 mm glass epoxy board

Operation range (Ta = 25) Parameter Symbol Min. Typ. Max Unit

Supply voltage VCC 2.8 5.0 5.5 V




Electrical characteristics 1 (unless otherwise specified, Ta=25、VCC=5V）


Unit Conditions 76360 76361 76362 76363

Circuit current 1 ICC1 12 11 mA When no signal Circuit current 2 ICC2 0.0 uA During standby

Circuit current 3 ICC3-1 13 12

mADuring output of color bar signal


Maximum output level VOM 4.6 3.8 3.4 Vpp f=10kHz, THD=1% Voltage gain GV 6.0 -0.1 dB Vin=1.0Vpp, f=100kHz

Frequency response GF1 0 － dB Vin=1.0Vpp, f=10MHz/100kHz GF2 － 0 dB Vin=1.0Vpp, f=30MHz/100kHz


CT -65 dB Vin=1.0Vpp, f=4.43MHz

Mute attenuation MT -65 dB Vin=1.0Vpp, f=4.43MHz

CTL pin switch level VTHH 1.2 Min V High Level threshold voltage VTHL 0.45 Max V Low Level threshold voltage

CTL pin inflow current ITHH 50 Max uA CTL pin = 2.0 V applied Input impedance Zin － 150 － 150 kΩ Differential gain DG 0.3 % Vin=1.0Vpp


DP-1 0.7 0.3 deg.



100% white video signal C-related S/N [AM] SNCA +75

dBVin = 1.0 Vpp, bandwidth: 100 to 500 kHz

100% chroma voltage signal C-related S/N [PM] SNCP +65 Electrical characteristics 2 (unless otherwise specified, Ta = 25, VCC = 3 V)


Unit Conditions 76360 76361 76362 76363

Circuit current 1 ICC1 10 mA When no signal Circuit current 2 ICC2 0.0 uA During standby

Circuit current 3 ICC3-1 11 10 mA During output of color bar signal


Maximum output level VOM 2.7 2.8 1.8 1.9 Vpp f=10kHz, THD=1% Voltage gain GV 6.0 -0.1 dB Vin=1.0Vpp, f=100kHz

Frequency response GF1 0 － dB Vin=1.0Vpp, f=10MHz/100kHz GF2 － 0 dB Vin=1.0Vpp, f=30MHz/100kHz


CT -65 dB Vin=1.0Vpp, f=4.43MHz

Mute attenuation MT -65 dB Vin=1.0Vpp, f=4.43MHz

CTL pin switch level VTHH 1.2 Min V High Level threshold voltage VTHL 0.45 Max V Low Level threshold voltage

CTL pin inflow current ITHH 50 Max uA CTL pin = 2.0 V applied Input impedance Zin － 150 － 150 kΩ Differential gain DG 0.3 % Vin=1.0Vpp


DP-1 1.0 0.3 deg.



100% white video signal C-related S/N [AM] SNCA +75 dB Vin = 1.0 Vpp, bandwidth: 100 to 500 kHz

100% chroma video signal C-related S/N [PM] SNCP +65 dB(Note) Re: ICC3, VOM, GV, GF, CT, MT, DG, DP, SNY, SNCA, SNCP parameters

BH76360FV, BH76361FV: RL = 150 BH76362FV, BH76363FV: RL = 10 k




Control pin settings

CTLA CTLB CTLC CTLD

IN1 L(OPEN) L(OPEN) L(OPEN) H

IN2 H L(OPEN) L(OPEN) H

IN3 L(OPEN) H L(OPEN) H

IN4 H H L(OPEN) H

IN5 L(OPEN) L(OPEN) H H

IN6 H L(OPEN) H H

MUTE ＊ H H H

STBY ＊＊＊ L(OPEN)

＊ L(OPEN) or H either is possible

Block diagram

Fig.1 BH76360FV

9 10 11 12 13 14 15 16

8 7 6 5 4 3 2 1

logic

IN4 GND IN3 GND IN2 VCC IN1 PVCC

IN5 CTLA CTLB CTLC PGND OUT CTLD IN6

Sync_Tip Clamp

Sync_Tip Clamp

Sync_Tip Clamp

Sync_Tip Clamp

Sync_Tip Clamp

6dB 75Ω

Sync_Tip Clamp

9 10 11 12 13 14 15 16

8 7 6 5 4 3 2 1

logic



BIAS

6dB 75Ω

BIAS BIAS BIAS

BIAS BIAS

Fig.2 BH76361FV

9 10 11 12 13 14 15 16

8 7 6 5 4 3 2 1

logic



Sync_Tip Clamp

Sync_Tip Clamp

Sync_Tip Clamp

Sync_Tip Clamp

Sync_Tip Clamp

Sync_Tip Clamp

0dB

9 10 11 12 13 14 15 16

8 7 6 5 4 3 2 1

logic



BIAS

0dB

BIAS BIAS BIAS

BIAS BIAS





I/O equivalent circuit diagrams

Input pins

Note 1) The above DC potential is only when VCC = 5 V. This value is a reference value and is not guaranteed.

Note 2) Numerical values shown in these figures are design values, and compliance to standards is not guaranteed.

Sync tip clamp input

BH76360FV / BH76362FV Bias input

BH76361FV / BH76363FV PIN No. Name Equivalent circuit PIN No. Name Equivalent circuit

2 4 6 8 9 11

IN1 IN2 IN3 IN4 IN5 IN6

2 4 6 8 9 11

IN1 IN2 IN3 IN4 IN5 IN6

Video signal input pin is used for sync tip clamp input.

・DC potential

BH76360FV：1.5V BH76362FV：1.0V

Video signal input pin is used for bias type input. Input

impedance is 150 k.

・DC potential

BH76361FV：3.1V BH76363FV：2.5V

Control pins

PIN No. Name Equivalent circuit

10

12

13

14

CTLA

CTLB

CTLC

CTLD

Switches operation mode [active or standby] and input

pin.

Threshold level is 0.45 V to 1.2 V.

Output pin

With video driver

BH76360FV / BH76361FV Without video driver

BH76362FV / BH76363FV PIN No. Name Equivalent circuit PIN No. Name

16 OUT

16 OUT

Video signal output pin. Able to drive loads up to 75

(dual drive).

・DC potential

BH76360FV：0.16V BH76361FV：2.5V

Video signal output pin.

・DC potential

BH76362FV：0.3V BH76363FV：1.8V

IN 100Ω

OUT

14kΩ

OUT

3.0mA

CTL 50kΩ

250kΩ

200kΩ

200kΩ

IN100Ω

150kΩ




9

10

11

12

13

14

15

16

8

7

6

5

4

3

2

1

logic

IN4

GND

IN3

GND

IN2

VCC

IN1

PVCC

IN5

CTLA

CTLB

CTLC

PGND

OUT

CTLD

IN6

6dB

75Ω

BIAS

470μF

75Ω VIDEO_OUT

VIDEO_IN

VIDEO_IN

4.7μF

4.7μF

4.7μF

4.7μF

4.7μF

4.7μF

0.1μF10μF

VCC

VIDEO_IN

VIDEO_IN

VIDEO_IN

VIDEO_IN

BIAS

BIAS

BIAS BIAS

BIAS

Test Circuit Diagrams

Application circuit examples

See pages 6/16 to 10/16 for description of how to determine the capacity of I/O coupling capacitors.

9

10

11

12

13

14

15

16

8

7

6

5

4

3

2

1

logic

IN4

GND

IN3

GND

IN2

VCC

IN1

PVCC

IN5

CTLA

CTLB

CTLC

PGND

OUT

CTLD

IN6 Sync_Tip Clamp

6dB

75Ω

Sync_Tip Clamp

Sync_Tip Clamp

Sync_Tip Clamp

Sync_Tip Clamp

Sync_Tip Clamp

470μF

75Ω VIDEO_OUT

VIDEO_IN

VIDEO_IN

0.1μF

0.1μF 10μF

VCC

VIDEO_IN

VIDEO_IN

VIDEO_IN

VIDEO_IN

0.1μF

0.1μF

0.1μF

0.1μF

0.1μF

16

OUT

75Ω VIDEO_OUT

出力コンデンサレス

で使用する場合

9

10

11

12

13

14

15

16

8

7

6

5

4

3

2

1

logic

IN4

GND

IN3

GND

IN2

VCC

IN1

PVCC

IN5

CTLA

CTLB

CTLC

PGND

OUT

CTLD

IN6

6dB

75Ω

75Ω

0.01μF

0.01μF 10μF

VCC

A

VCC

50Ω

0.01μF

50Ω

0.01μF

50Ω

0.01μF

50Ω

V V75Ω

A

0.01μF

50Ω

0.01μF

50Ω

A

A

A

Clamp/ Bias

Clamp/ Bias

Clamp/ Bias

Clamp/ Bias

Clamp/ Bias

Clamp/ Bias

10μF

9

10

11

12

13

14

15

16

8

7

6

5

4

3

2

1

logic

IN4

GND

IN3

GND

IN2

VCC

IN1

PVCC

IN5

CTLA

CTLB

CTLC

PGND

OUT

CTLD

IN6

0dB

0.01μF

0.01μF10μF

VCC

A

VCC

50Ω

0.01μF

50Ω

0.01μF

50Ω

0.01μF

50Ω

V V10kΩ

A

0.01μF

50Ω

0.01μF

50Ω

A

A

A

Clamp/Bias

Clamp/Bias

Clamp/Bias

Clamp/Bias

Clamp/ Bias

Clamp/ Bias

10μF

Fig.5 BH76360FV/BH76361FV Test Circuit Diagram

9

10

11

12

13

14

15

16

8

7

6

5

4

3

2

1

logic

IN4

GND

IN3

GND

IN2

VCC

IN1

PVCC

IN5

CTLA

CTLB

CTLC

PGND

OUT

CTLD

IN6 Sync_Tip Clamp

0dB

Sync_Tip Clamp

Sync_Tip Clamp

Sync_Tip Clamp

Sync_Tip Clamp

Sync_Tip Clamp

VIDEO_OUT

VIDEO_IN

VIDEO_IN

0.1μF

0.1μF 10μF

VCC

VIDEO_IN

VIDEO_IN

VIDEO_IN

VIDEO_IN

0.1μF

0.1μF

0.1μF

0.1μF

0.1μF

9

10

11

12

13

14

15

16

8

7

6

5

4

3

2

1

logic

IN4

GND

IN3

GND

IN2

VCC

IN1

PVCC

IN5

CTLA

CTLB

CTLC

PGND

OUT

CTLD

IN6

0dB

BIASVIDEO_OUT

VIDEO_IN

VIDEO_IN

4.7μF

4.7μF

4.7μF

4.7μF

4.7μF

4.7μF

0.1μF10μF

VCC

VIDEO_IN

VIDEO_IN

VIDEO_IN

VIDEO_IN

BIAS

BIAS

BIAS BIAS

BIAS


Test circuit diagrams are used for shipment inspections, and differ from application circuits.

Fig.6 BH76362FV/BH76363FV Test Circuit Diagram





Cautions for selection and use of application parts

When using this IC by itself ①

Method for determining capacity of input coupling capacitor

The HPF is comprised of an input coupling capacitor and the internal input impedance Zin of the IC. Since the fc value of this HPF is

determined using the following equation (a), the above recommended capacity for the input capacitor is derived. Usually, the cutoff

frequency fc is several Hz.

fc = 1 / (2π × C × Zin)・・・・(a)

When evaluating the sag characteristics and determining the capacity of the capacitor during video signal input, a horizontal stripe signal

called "H bar" (shown in Fig. 10) is suitable, and this type of signal is used instead of a color bar signal to evaluate characteristics and

determine capacity.

Method for determining capacity of output coupling capacitor

The output pins of models with a 75 driver [BH76360FV and BH76361FV] have an HPF comprised of an output coupling capacitor and

load resistance RL (= 150). When fc is set to approximately 1 Hz or 2 Hz, the capacity of the output coupling capacitor needs to be

approximately 470 µF to 1000 µF.

As for models without the 75 driver, an HPF is similarly comprised using the capacity of the output coupling capacitor and the input

impedance of the IC connected at the next stage, and the capacitance required for the output coupling capacitor should be estimated using

equation (a).

When this IC is used as a standalone device ②

In models that include a 75 driver [BH76360FV and BH76361FV], up to two monitors (loads) can be connected (a connection example is

shown in Fig. 12). When there are multiple loads, the number of output coupling capacitors must be increased or a larger capacitance must

be used, based on the table shown below.

Application circuit example No. of output capacitors Capacitance per output capacitor (recommended values)

Fig12(a) No. of drives required 470 µF to 1000 µF (same as with one drive)

Fig12(b) 1 (No. of drive × 470 µF to 1000) uF

When this IC is used as a standalone device ③

The BH76360FV is the only model that can be used without an output coupling capacitor.

This use method not only enables reductions in board space and part-related costs, but it is able to improve the sag characteristics by

improving low-range frequency response. However, when the output coupling capacitor is omitted, a direct current flows to the connected

set, so the specifications of the connected set should be noted carefully before starting use.

Note also that only one load can be connected when the output coupling capacitor is omitted.

Input type Input impedance

Zin

Capacity of input coupling

capacitor (recommended value)

Capacity of output coupling

capacitor (recommended value)

Sync_Tip_Clamp 10MΩ 0.1uF 470uF~1000uF

Bias 150kΩ 4.7uF

Fig.11 Example of Screen with Obvious Sag (H-bar Signal)

Fig. 12 (a) Application Circuit Example 1 (Two Drives) Fig. 12 (b) Application Circuit Example 2 (Two Drives)

16OUT

75Ω

75Ω

monitor

BH76360FV

Fig.13 Application Example without Output Coupling Capacitor

Voltage at output ≒0.16V When this voltage load resistance is applied,

a direct current is generated.

16 OUT

470μF

75Ω

75Ω

470μF

75Ω

75Ω

monitor

monitor

16OUT

(470×2)μF

75Ω

75Ω

75Ω

75Ω

monitor

monitor




When using several of these ICs ①

When several of these ICs are used, it enables applications in which separate images are output to the car navigation system's front and

rear monitors.

When several ICs are used at the same time, the number of parallel connections of input impedance equals the number of ICs being used,

which reduces the input impedance. This also raises the fc value of the HPF formed at the input pin block, so the capacitance of the input

coupling capacitor must be increased according to equation (a). The recommended values for calculation results are listed in the table

below.

When a clamp is used as the input type, the original input impedance becomes much greater, and if two or three are used at the same

time there is no need to change the capacitance of the input coupling capacitor.

Input type Input impedance per ICNumber of ICs

used

Total

input impedance

Capacitance of input

coupling capacitor

(recommended values)

Sync_Tip_Clamp Approx. 10 M 2 Approx. 5 M 0.1uF

3 Approx. 3 M 0.1uF

Bias 150kΩ 2 75kΩ 6.8uF~

3 50kΩ 10uF~

When using several of these ICs ②

When three bias input type models (BH76361FV or BH76363FV) are used in parallel, they can be used for RGB signal switching

applications. Likewise, when one clamp input type model (BH76360FV or BH76362FV) is connected in parallel with two bias input type

models (a total of three ICs used in parallel), they can be used for component signal switching applications. The same method can be used

to determine the capacitance of I/O coupling capacitors of these applications.

16

2

IN1

OUT

Clamp /Bias

470μF

75Ω

75Ω

4

IN2

Clamp /Bias

6

IN3

Clamp /Bias

2

IN1

Clamp /Bias

4

IN2

Clamp /Bias

6

IN3

Clamp /Bias

VIDEO IN

VIDEO IN

VIDEO IN

16 OUT

470μF

75Ω

75Ω

Front monitor Rear monitor

Fig.14 Application Example when Using Several ICs

16

2

IN1

OUT

Bias

4

IN2

Bias

6

IN3

Bias

16

2

IN1

OUT

Bias

4

IN2

Bias

6

IN3

Bias

VIDEO IN[R1]

16

2

IN1

OUT

Bias

4

IN2

Bias

6

IN3

Bias

VIDEO IN[R2]

VIDEO IN[R3]

VIDEO IN[G1]

VIDEO IN[G2]

VIDEO IN[G3]

VIDEO IN[B1]

VIDEO IN[B2]

VIDEO IN[B3]

R_OUT

G_OUT

B_OUT

SW セレクト

BH76361FV

or BH76363FV

BH76361FV

or BH76363FV

BH76361FV

or BH76363FV

4.7μF

4.7μF

4.7μF

4.7μF

4.7μF

4.7μF

4.7μF

4.7μF

4.7μF

16

2

IN1

OUT

Clamp

4

IN2

Clamp

6

IN3

Clamp

16

2

IN1

OUT

Bias

4

IN2

Bias

6

IN3

Bias

VIDEO IN[Py1]

16

2

IN1

OUT

Bias

4

IN2

Bias

6

IN3

Bias

VIDEO IN[Py2]

VIDEO IN[Py3]

VIDEO IN[Pb1]

VIDEO IN[Pb2]

VIDEO IN[Pb3]

VIDEO IN[Pr1]

VIDEO IN[Pr2]

VIDEO IN[Pr3]

Py_OUT

Pb_OUT

Pr_OUT

SW セレクト

BH76360FV

or BH76362FV

BH76361FV

or BH76363FV

BH76361FV

or BH76363FV

0.1uF

0.1uF

0.1uF

4.7uF

4.7uF

4.7uF

4.7uF

4.7uF

4.7uF

Fig. 15 (a). RGB Signal Switching Application Example (using three bias input type models in parallel)

Fig. 15 (b). Component Signal Switching Application Example(using one clamp input type model and two bias input type models in parallel)




Cautions for use

1. The numerical values and data shown here are typical design values, not guaranteed values.

2. The application circuit examples show recommended circuits, but characteristics should be checked carefully before using

these circuits. If any external part constants are modified before use, factors such as variation in all external parts and

ROHM LSI ICs, including not only static characteristics but also transient characteristics, should be fully considered to set

an ample margin.

3. Absolute maximum ratings

If the absolute maximum ratings for applied voltage and/or operation temperature are exceeded, LSI damage may result.

Therefore, do not apply voltage or use in a temperature that exceeds these absolute maximum ratings. If it is possible that

absolute maximum ratings will be exceeded, use a physical safety device such as a fuse and make sure that no conditions

that might exceed the absolute maximum ratings will be applied to the LSI IC.

4. GND potential

Regardless of the operation mode, the voltage of the GND pin should be at least the minimum voltage. Actually check

whether or not the voltage at each pin, including transient phenomena, is less than the GND pin voltage.

5. Thermal design

The thermal design should be done using an ample margin that takes into consideration the allowable dissipation under

actual use conditions.

6. Shorts between pins and mounting errors

When mounting LSI ICs onto the circuit board, make sure each LSI's orientation and position is correct. The ICs may

become damaged if they are not mounted correctly when the power is turned on. Similarly, damage may also result if a

short occurs, such as when a foreign object is positioned between pins in an IC, or between a pin and a power supply or

GND connection.

7. Operation in strong electromagnetic field

When used within a strong electromagnetic field, evaluate carefully to avoid the risk of operation faults.

8. Place the power supply's decoupling capacitor as close as possible to the VCC pin (PIN 1,PIN3) and GND pin (PIN 5, PIN7,

PIN15).

9. With a clamp input type model (BH76360FV or BH76362FV), if any unused input pins are left open they will oscillate, so

unused input pins should instead be connected to GND via a capacitor or else directly connected to VCC.

10. With models that do not include a 75driver (BH76362FV or BH76363FV), in some cases the capacitance added to the set

board may cause the peak frequency response to occur at a high frequency. To lower the peak frequency, connect in

series resistors having resistance of several dozen to several hundred as close as possible to the output pin.

11. Frequency response in models that do not include a 75- driver (BH76362FV and BH76363FV) was measured as 100

kH/30 MHz: 0 dB (Typ.) in the application circuit examples (shown in Fig. 9 and Fig. 10), and when resistance of about 1 or

2 k is applied from the IC's output pin to GND, this frequency response can be improved (the lower limit of the applied

resistance should be 1 k). In such cases, gain is reduced, since the output voltage is divided by the added resistance

and the output resistance of the IC.

-7

-6

-5

-4

-3

-2

-1

0

1

1M 10M 100M 1000M周波数[Hz]

電圧

利得

[dB

]

(c) Voltage gain fluctuation when resistance is inserted [f = 100 kHz] (Voltage gain without inserted resistance: -0.11 dB)

16 OUT

Resistance to improve frequency response (R: 1-2 kΩ)

3mA

Fig.17 Result of Resistance Inserted to Improve BH76362FV/BH76363FV Frequency Response

(a) Resistor insertion points (b) Frequency response changes when resistance is inserted

Input amplitude: 1 Vpp, Output load resistance: 10 kΩ Other constants are as in application examples (Figs. 9 & 10)

-0.20

-0.18

-0.16

-0.14

-0.12

-0.10

0.5 1 1.5 2 2.5

出力端子付加抵抗値[kΩ]

GA

IN@

f=100kH

z[dB

]

R=1kΩ

R=2kΩ

抵抗なし

Fig.16 Positions where Resistors are Inserted to Lower Peak Frequency Response in BH76362FV or BH76363FV

16OUT

Resistors (several dozen Ω to several hundredΩ) to lower peak frequency

Output pin

No resistance

Vo

ltage

ga

in [d

B]

Frequency [Hz] Resistance added to output pin [k]




12. With clamp input type models (BH76360FV and BH76362FV), if the termination impedance of the video input pin becomes

higher, sync contractions or oscillation-related problems may occur. Evaluate temperature and other characteristics

carefully and use at 1 k or less.

Evaluation board pattern diagram and circuit diagram

Parts list Symbol Function Recommended value Comments

R2 R4 R6

R8 R9 R11 Input terminating resistor 75Ω －

C2 C4 C6

C8 C9 C11

Input coupling


R161 Output resistor 75Ω －

C16 Output coupling


C01(C03) Decoupling capacitor

10uF B characteristics recommended

C02(C04) 0.1uF

BH76360~5FV

IN5-RCA

C9

GND

GND

GND

VCC

IN1 IN2 IN3 IN4

GND

GND

OUT-RCA OUT

OUT

SW10 SW12 SW13 SW14

CTLA CTLB CTLC CTLD

H

L

H

L

H

L

H

L

H164

H162

H163

R163

R162

R164

IN6-RCA

C11

R9

R11

IN6

IN5

CTLC CTLA

CTLD CTLB

H161

R161

C16

C01

C03

C04

C02

U1

IN5

IN6

CTLA

H

1

CTLB

H

2

CTLC

H

3

CTLD

H

4

IN4

IN3

IN2

IN1

R2

R4

R6

R8

C8

C6

C4

C2

IN1-

RC

A

IN2-

RC

A

IN3-

RC

A

IN4-

RC

A

Fig.19 Evaluation Board Circuit Diagram

1

2

3

4

5

6

7

8 9

10

11

12

13

14

15

16

RCA

+

C2

GND

BH7636xFV

GND GND GND GND

+ IN1

R275

IN1-RCAIN1

RCA

C4

+ IN2

R475

IN2-RCAIN2

RCA

C6

+ IN3

R675

IN3-RCAIN3

RCA

C8

+ IN4

R875

IN4-RCAIN4

+

47u 0.1u

+

RCA

+

R9

RCA

IN5 C9 IN5-RCA

75

IN5

+

R11

RCA

IN6 C11 IN6-RCA

75

IN6

CTLA

CTLB

H1

CTLC

CTLD

H2

H4 HL

CTLA

CTLB

CTLC

CTLD SW14

SW13

SW10

SW12

OUTOUT

470u

C16

H161

H162 H163 H164

R162

R163

R164150

150

75

R16175

OUT-RCA

VCC

47u

0.1u

H3

C01

C02

C03 C04

A-13AP

Fig.20 Evaluation Board Pattern Diagram

BH7636xFV

0

1

2

3

4

5

6

0 1k 2k 3k

入力終端抵抗Rin[Ω]

入力

端子

での

sync縮

み量

[%]

Fig. 18. Relation between Input Pin Termination Impedance and Amount of Sync Contraction

Input termination resistance Rin [Ω] A

mo

un

t of

syn

c co

ntr

actio

n

at

inpu

t pin

[%

]




Reference data (1) BH76360FV / BH76361FV [unless otherwise specified, output capacitance C: 470 µF, RL = 150 ]

0

5

10

15

20

2 3 4 5 6電源電圧[V]

回路

電流

[mA

]


出力Cレス


Fig.26 ICC2 vs. Ambient Temperature

Ta=25

VCC=5V



Fig.25 ICC2 vs. Supply Voltage

0

5

10

15

20

-50 0 50 100

周囲温度[]

回路

電流

[mA]


出力Cレス

.

Ta=25

BH76360/61FV

BH76360FV

VCC=5V


BH76360/61FV

BH76360FV

BH76360FV

Ta=25

VCC=3V

Ta=25

VCC=5V

5.7

5.8

5.9

6.0

6.1

6.2

6.3

-50 0 50 100

周囲温度[]

電圧

利得

[dB

]


5.7

5.8

5.9

6.0

6.1

6.2

6.3

2 3 4 5 6

電源電圧[V]

電圧

利得

[dB

]

Fig.33 GV vs. Supply Voltage

Fig.34 GV vs. Ambient Temperature

BH76360FV

BH76360FV

-2.0

-1.5

-1.0

-0.5

0.0

0.5

1.0

2 3 4 5 6

電源電圧[V]

周波

数特

性(1

00k/1

0MH

z)[d

B]

-2.0

-1.5

-1.0

-0.5

0.0

0.5

1.0

-50 0 50 100

周囲温度[]

周波

数特

性(1

00k/10M

Hz)[

dB]

Ta=25

VCC=5V

BH76360FV

BH76360FV

BH76360FV

0

5

10

15

20

2 3 4 5 6

電源電圧[V]

回路

電流

[mA

]

Ta=25

BH76361FV

VCC=5V

BH76361FV

Ta=25

BH76361FV

BH76361FV

VCC=3V

Ta=25

BH76361FV

BH76361FV

VCC=5V

-0.5

0.0

0.5

1.0

1.5

2.0

2 3 4 5 6

電源電圧[V]

回路

電流

(ST

BY

)[μ

A]

-0.5

0.0

0.5

1.0

1.5

2.0

-50 0 50 100

周囲温度[]

回路

電流

（S

TB

Y)[

μA

]

2.0

2.2

2.4

2.6

2.8

3.0

-50 0 50 100

周囲温度[]

最大

出力

レベ

ル[V

pp]

2.0

3.0

4.0

5.0

6.0

2 3 4 5 6

電源電圧[V]

最大

出力

レベ

ル[V

pp]

0

5

10

15

20

-50 0 50 100

周囲温度[]

回路

電流

[mA

]

2.0

3.0

4.0

5.0

6.0

2 3 4 5 6

電源電圧[V]

最大

出力

レベ

ル[V

pp]

2.0

2.2

2.4

2.6

2.8

3.0

-50 0 50 100

周囲温度[]

最大

出力

レベ

ル[V

pp]

5.7

5.8

5.9

6.0

6.1

6.2

6.3

-50 0 50 100

周囲温度[]

電圧

利得

[dB

]

5.7

5.8

5.9

6.0

6.1

6.2

6.3

2 3 4 5 6

電源電圧[V]

電圧

利得

[dB

]

Supply Voltage [V]

Circ

uit

curr

en

t [m

A]

Circ

uit

curr

en

t [m

A]


Circ

uit

curr

en

t [m

A]

Supply Voltage [V]Ambient Temperature []

Circ

uit

curr

en

t [m

A]

Circ

uit

curr

en

t (S

TB

Y)

[μA

]


Circ

uit

curr

en

t (S

TB

Y)

[μA

]

Ma

xim

um

ou

tpu

t le

vel [

Vpp

]


Ma

xim

um

ou

tpu

t le

vel [

Vpp

]

Ma

xim

um

ou

tpu

t le

vel [

Vpp

]


Vo

ltage

ga

in [d

B]

Vo

ltage

ga

in [d

B]


Vo

ltage

ga

in [d

B]

Vo

ltage

ga

in [d

B]

Supply Voltage [V] Ambient Temperature [] Fre

quen

cy r

espo

nse

(100

kH

z/10

MH

z) [

dB]

Fre

quen

cy r

espo

nse

(100

kH

z/10

MH

z) [

dB]









Ta=25

VCC=5V, Ta=25

Fig.37 GF vs. Supply Voltage Fig.38 GF vs. Ambient Temperature Fig.39 Frequency Response

BH76360/61FV

BH76361FV

VCC=5V

-75

-73

-71

-69

-67

-65

-50 0 50 100

周囲温度[]

チャ

ンネ

ル間

クロ

スト

ーク

(wor

st)

[dB

]

-75

-73

-71

-69

-67

-65

2 3 4 5 6

電源電圧[V]

チャ

ンネ

ル間

クロ

スト

ーク

(wors

t)[d

B]

BH76360/61FV

VCC=5V

-80

-78

-76

-74

-72

-70

-50 0 50 100

周囲温度[]

ミュ

ート

減衰

量(w

ors

t)[d

B]

-80

-78

-76

-74

-72

-70

2 3 4 5 6

電源電圧[V]

ミュ

ート

減衰

量(w

orst

)[dB

]

Ta=25

BH76360/61FV

BH76360/61FV

VCC=5V

-15

-10

-5

0

5

1M 10M 100M

Frequency[Hz]

Gai

n[d

B]

BH76360FV

VCC=5V, Ta=25

BH76360/61FV

VCC=5V BH76360/61FV

0.0

0.5

1.0

1.5

2.0

2 3 4 5 6

電源電圧[V]

微分

利得

[%]

Ta=25

BH76360FV

0.0

0.5

1.0

1.5

2.0

-50 0 50 100

周囲温度[]

微分

利得

[%]

VCC=5V

BH76361FV

BH76361FV

0.0

0.5

1.0

1.5

2.0

-50 0 50 100

周囲温度[]

微分

位相

[deg] 出力C容量：470uF

出力Cレス

BH76360FV

Ta=25

BH76360FV

VCC=5V BH76360FV

Ta=25

BH76361FV

VCC=5V, Ta=25

BH76361FV

Ta=25

VCC=5V

0

0.5

1

1.5

2

2 3 4 5 6

電源電圧[V]

微分

利得

[%]

0

0.5

1

1.5

2

-50 0 50 100

周囲温度[]

微分

利得

[%]

0

10

20

30

40

50

60

70

-50 0 50 100周囲温度[]

CT

L端子

流入

電流

[uA

]

0

5

10

15

20

0 0.5 1 1.5 2

CTL_D端子電圧

回路

電流

[mA

]

-15

-10

-5

0

5

1M 10M 100M

Frequency[Hz]

Gai

n[d

B]

-2.0

-1.5

-1.0

-0.5

0.0

0.5

1.0

2 3 4 5 6

電源電圧[V]

周波

数特

性(1

00k/1

0MH

z)[d

B]

-2.0

-1.5

-1.0

-0.5

0.0

0.5

1.0

-50 0 50 100

周囲温度[]

周波

数特

性(1

00k/10M

Hz)[

dB]

0.0

0.5

1.0

1.5

2.0

2 3 4 5 6

電源電圧[V]

微分

位相

[deg.]


出力Cレス

Fre

quen

cy r

espo

nse

(100

kH

z/10

MH

z) [

dB]

Fre

quen

cy r

espo

nse

(100

kH

z/10

MH

z) [

dB]


Fig. 40 Frequency Response

Cro

ssta

lk b

etw

een

chan

nels

(w

orst

) [d

B]


Fig.42 CT(worst) vs. Ambient Temperature


Mu

te a

tten

uat

ion

(w

ors

t) [

dB

]

Mu

te a

tten

uat

ion

(w

ors

t) [

dB

]

Fig.43 MT(worst) vs. Supply Voltage Fig.44 MT(wrost) vs. Ambient Temperature

Circ

uit

curr

en

t [m

A]

CTL_D pin voltage [V]

CT

L p

in in

flux

curr

en

t [µ

A]


Fig. 45 CTLd pin voltage vs Circuit Current (CLT threshold )


Diff

ere

ntia

l ga

in [%

]

Diff

ere

ntia

l ga

in [%

]



Diff

ere

ntia

l ga

in [%

]

Diff

ere

ntia

l ga

in [%

]

Diff

ere

ntia

l ph

ase

[de

g.]

Diff

ere

ntia

l ph

ase

[de

g.] Output capacitance C: 470 µF

No output capacitance Output capacitance C: 470 µF







Reference data (2) BH76362FV/BH76363FV [unless otherwise specified, output capacitance C: 470 µF, RL = 10 k]

1.5

1.7

1.9

2.1

2.3

2.5

-50 0 50 100

周囲温度[]

最大

出力

レベ

ル[V

pp]

0

0.5

1

1.5

2

-50 0 50 100

周囲温度[]

微分

位相

[deg]

0

0.5

1

1.5

2

2 3 4 5 6

電源電圧[V]

微分

位相

[deg.]

Ta=25

VCC=5V

BH76361FV

BH76361FV

BH76360/61FV

BH76360/61FV

Ta=25

VCC=5V

BH76360/61FV

BH76360/61FV

Ta=25

VCC=5V

BH76360/61FV

BH76360/61FV

Ta=25

VCC=5V

-0.5

0.0

0.5

1.0

1.5

2.0

2 3 4 5 6

電源電圧[V]

回路

電流

(ST

BY

)[μ

A]

-0.5

0.0

0.5

1.0

1.5

2.0

-50 0 50 100

周囲温度[]

回路

電流

（ST

BY

)[μ

A]

0

5

10

15

20

2 3 4 5 6

電源電圧[V]

回路

電流

[mA

]

BH76362FV

BH76362FV

Ta=25

VCC=5V

0

5

10

15

20

-50 0 50 100

周囲温度[]

回路

電流

[mA

]

0

5

10

15

20

2 3 4 5 6

電源電圧[V]

回路

電流

[mA

]

0

5

10

15

20

-50 0 50 100

周囲温度[]

回路

電流

[mA

]

BH76363FV

BH76363FV

Ta=25

VCC=5V

Ta=25

VCC=5V

BH76362/63FV

BH76362/63FV

BH76362FV

BH76362FV

Ta=25

VCC=3V

1.0

2.0

3.0

4.0

5.0

2 3 4 5 6

電源電圧[V]

最大

出力

レベ

ル[V

pp]

70

72

74

76

78

80

2 3 4 5 6

電源電圧[V]

C系

S/N

(AM

)[dB

]

70

72

74

76

78

80

-50 0 50 100

周囲温度[]

C系

S/N

(AM

)[dB

]

65

66

67

68

69

70

2 3 4 5 6

電源電圧[V]

C系

S/N

(PM

)[dB

]

65

66

67

68

69

70

-50 0 50 100周囲温度[]

C系

S/N

(PM

)[dB

]

70

72

74

76

78

80

2 3 4 5 6

電源電圧[V]

Y系

S/N

[dB

]

70

72

74

76

78

80

-50 0 50 100

周囲温度[]

Y系

S/N

[dB

]

Diff

ere

ntia

l ph

ase

[de

g.]

Diff

ere

ntia

l ph

ase

[de

g.]


Y S

/N [

dB]

Y S

/N [

dB]



C S

/N (

AM

) [d

B]

C S

/N (

AM

) [d

B]

C S

/N (

PM

) [d

B]

C S

/N (

PM

) [d

B]





Circ

uit

curr

en

t [m

A]

Circ

uit

curr

en

t [m

A]

Circ

uit

curr

en

t [m

A]

Circ

uit

curr

en

t [m

A]

Fig.61 ICC1 vs. Supply Voltage Fig.62 ICC1 vs. Ambient Temperature Fig.63 ICC1 vs. Supply Voltage Fig.64 ICC1 vs. Ambient Temperature


Circ

uit

curr

en

t (S

TB

Y)

[μA

]

Circ

uit

curr

en

t (S

TB

Y)

[μA

]

Ma

xim

um

ou

tpu

t le

vel [

Vpp

]

Ma

xim

um

ou

tpu

t le

vel [

Vpp

]

Fig.66 ICC2 vs. Ambient Temperature Fig.65 ICC2 vs. Supply Voltage Fig.67 Vom vs. Supply Voltage Fig.68 Vom vs. Ambient Temperature




Ta=25

VCC=5V

BH76362FV

BH76362FV

Ta=25

BH76363FV

BH76363FV

VCC=3V

1.5

1.7

1.9

2.1

2.3

2.5

-50 0 50 100

周囲温度[]

最大

出力

レベ

ル[V

pp]

1.0

2.0

3.0

4.0

5.0

2 3 4 5 6

電源電圧[V]

最大

出力

レベ

ル[V

pp]

Ta=25

BH76363FV

BH76363FV

VCC=5V

Ta=25

VCC=5V

BH76362FV

BH76362FV

Ta=25

BH76363FV

BH76363FV

VCC=5V

-5

-4

-3

-2

-1

0

1

2


Gai

n[d

B]

VCC=5V ,Ta=25

BH76363FV

BH76362FV

VCC=5V ,Ta=25

-75

-73

-71

-69

-67

-65

-50 0 50 100

周囲温度[]

チャ

ンネ

ル間

クロ

スト

ーク

(wor

st)

[dB

]

-75

-73

-71

-69

-67

-65

2 3 4 5 6

電源電圧[V]

チャ

ンネ

ル間

クロ

スト

ーク

(wors

t)[d

B]

-80

-78

-76

-74

-72

-70

-50 0 50 100

周囲温度[]

ミュ

ート

減衰

量(w

ors

t)[d

B]

-80

-78

-76

-74

-72

-70

2 3 4 5 6

電源電圧[V]

ミュ

ート

減衰

量(w

orst)

[dB

]

BH76362/63FV

Ta=25

VCC=5V

BH76362/63FV

BH76362/63FV

Ta=25

VCC=5V

BH76362/63FV

-2.0

-1.5

-1.0

-0.5

0.0

0.5

1.0

2 3 4 5 6

電源電圧[V]

周波

数特

性(1

00k/3

0M

Hz)[

dB

]

-2.0

-1.5

-1.0

-0.5

0.0

0.5

1.0

-50 0 50 100

周囲温度[]

周波

数特

性(1

00k/

30M

Hz)

[dB

]

-2.0

-1.5

-1.0

-0.5

0.0

0.5

1.0

2 3 4 5 6

電源電圧[V]

周波

数特

性(1

00k/

30M

Hz)[

dB]

-2.0

-1.5

-1.0

-0.5

0.0

0.5

1.0

-50 0 50 100

周囲温度[]

周波

数特

性(1

00k

/30

MH

z)[

dB

]-0.6

-0.4

-0.2

0.0

0.2

0.4

2 3 4 5 6

電源電圧[V]

電圧

利得

[dB

]

-0.6

-0.4

-0.2

0.0

0.2

0.4

-50 0 50 100

周囲温度[]

電圧

利得

[dB

]

-0.6

-0.4

-0.2

0.0

0.2

0.4

2 3 4 5 6

電源電圧[V]

電圧

利得

[dB

]

-0.6

-0.4

-0.2

0.0

0.2

0.4

-50 0 50 100

周囲温度[]

電圧

利得

[dB

]

-5

-4

-3

-2

-1

0

1

2


Gai

n[d

B]

Ma

xim

um

ou

tpu

t le

vel [

Vpp

]

Ma

xim

um

ou

tpu

t le

vel [

Vpp

]

Vo

ltage

ga

in [d

B]

Vo

ltage

ga

in [d

B]




Vo

ltage

ga

in [d

B]

Vo

ltage

ga

in [d

B]


Fre

quen

cy r

esp

onse

(10

0 kH

z/10

MH

z) [

dB]

Fre

quen

cy r

esp

onse

(10

0 kH

z/10

MH

z) [

dB]

Fig.75 GF vs. Supply Voltage Fig.76 GF vs. Ambient Temperature Fig.73 GV vs. Supply Voltage Fig.74 GV vs. Ambient Temperature

Fre

quen

cy r

esp

onse

(10

0 kH

z/10

MH

z) [

dB]

Fre

quen

cy r

esp

onse

(10

0 kH

z/10

MH

z) [

dB]


Fig.77 GF vs. Supply Voltage Fig.78 GF vs. Ambient Temperature Fig. 79 Frequency Response Fig. 80 Frequency Response

Cro

ssta

lk b

etw

een

cha

nn

els

(w

ors

t) [

dB]

Cro

ssta

lk b

etw

een

cha

nn

els

(w

ors

t) [

dB]

Mu

te a

tten

uat

ion

(w

ors

t) [

dB

]

Mu

te a

tten

uat

ion

(w

ors

t) [

dB

]







0.0

0.5

1.0

1.5

2.0

-50 0 50 100

周囲温度[]

微分

位相

[%]

0.0

0.5

1.0

1.5

2.0

-50 0 50 100

周囲温度[]

微分

位相

[%]

0.0

0.5

1.0

1.5

2.0

2 3 4 5 6

電源電圧[V]

微分

位相

[deg.]

0.0

0.5

1.0

1.5

2.0

-50 0 50 100

周囲温度[]

微分

利得

[%]

0.0

0.5

1.0

1.5

2.0

2 3 4 5 6

電源電圧[V]

微分

利得

[%]

0

0.5

1

1.5

2

-50 0 50 100

周囲温度[]

微分

利得

[%]

0

10

20

30

40

50

60

70

-50 0 50 100周囲温度[]

CT

L端

子流

入電

流[u

A]

VCC=5V

BH76362/63FV

BH76362FV

Ta=25

VCC=5V

BH76362FV

BH76362FV

Ta=25

VCC=5V

BH76362FV

BH76363FV

Ta=25

BH76363FV

Ta=25

BH76362/63FV

VCC=5V, Ta=25

0.0

0.5

1.0

1.5

2.0

2 3 4 5 6

電源電圧[V]

微分

利得

[%]

BH76363FV

VCC=5V

0.0

0.5

1.0

1.5

2.0

2 3 4 5 6

電源電圧[V]

微分

位相

[%]

BH76363FV

VCC=5V

BH76362/63FV

Ta=25

VCC=5V

BH76362/63FV

BH76362/63FV

Ta=25

VCC=5V

BH76362/63FV

70

72

74

76

78

80

2 3 4 5 6

電源電圧[V]

C系

S/N

(AM

)[dB

]

70

72

74

76

78

80

-50 0 50 100

周囲温度[]

C系

S/N

(AM

)[dB

]

65

66

67

68

69

70

2 3 4 5 6

電源電圧[V]

C系

S/N

(PM

)[dB

]

65

66

67

68

69

70

-50 0 50 100周囲温度[]

C系

S/N

(PM

)[dB

]

70

72

74

76

78

80

2 3 4 5 6

電源電圧[V]

Y系

S/N

[dB

]

70

72

74

76

78

80

-50 0 50 100

周囲温度[]

Y系

S/N

[dB

]

Ta=25

VCC=5V

0

5

10

15

20

0 0.5 1 1.5 2

CTL_D端子電圧

回路

電流

[mA

]

BH76362/63FV

BH76362/63FV

Circ

uit

curr

en

t [m

A]

CTL_D pin voltage [V]

CT

L p

in in

flux

curr

en

t [µ

A]


Diff

ere

ntia

l ga

in [%

]

Diff

ere

ntia

l ga

in [%

]

Ambient Temperature []Supply Voltage [V]

Fig.85 CTLd pin voltage vs Circuit Current (CLT threshold )



Supply Voltage [V]Supply Voltage [V] Ambient Temperature [] Ambient Temperature []

Diff

ere

ntia

l ph

ase

[de

g.]

Diff

ere

ntia

l ph

ase

[de

g.]

Diff

ere

ntia

l ga

in [%

]

Diff

ere

ntia

l ga

in [%

]


Diff

ere

ntia

l ph

ase

[de

g.]

Diff

ere

ntia

l ph

ase

[de

g.]

Y S

/N [

dB]

Y S

/N [

dB]




C S

/N (

AM

) [d

B]

C S

/N (

AM

) [d

B]

C S

/N (

PM

) [d

B]

C S

/N (

PM

) [d

B]







External dimensions and label codes

Fig.101 External Dimensions of BH7636xFV Series Package When used with 3-input, 1-output video switch BH7633xFVM

Fig. 14 above shows an application example in which two of these ICs are used. When the similar IC models BH7633xFVM and BH7636xFV are used at the same time, the type of configuration shown below can be combined. In such cases, input coupling capacitors can be used, as in the application example in Fig. 14.

Fig.102 Application Example in which BH76330FVM and BH76360FV Are Used Concurrently For details of BH7633xFVM, see the BH7633xFVM Series Application Notes.

Rear monitor

SSOP-B16 (unit: mm )

７６３６０

Lot.No. Model Code

BH76360FV 76360

BH76361FV 76361

BH76362FV 76362

BH76363FV 76363

16

2

IIN1

OUT

Clamp

75Ω

75Ω

フロントモニタ

4

IIN2

Clamp

6

IIN3

Clamp

16

1

OUT

Clamp

75Ω

75Ω

リアモニタ

3

Clamp

5

Clamp

外部入力

TV

DVD

※2

BH76360FV

BH76330FVM

8

IIN4

Clamp

9

IIN5

Clamp

11

IIN6

Clamp

ナビ画面

リアカメラ

IIN1

IIN2

IIN3

※3

※1

※2

＊1 Input coupling capacitor can be used with

this. ＊2 Output coupling capacitors can be omitted

when using BH76330FVM or BH76360FV, and this helps reduce the number of parts.

＊3 Any inputs that are not used should be

connected directly to VCC or shorted with GND via a capacitor.

External input

Navigation screen

Rear camera

Front monitor

Rear monitor




Selection of order type

B H 7 6 3 3 0 F V

Part No. BH76330FVM BH76331FVM BH76360FV BH76361FV

M T R

BH76332FVMBH76333FVM BH76362FV BH76363FV

<Tape and Reel information> Embossed carrier tape

TR (The direction is the 1pin of product is at the upper right when you hold reel on the left hand and you pull out the tape on the right hand)

Tape

Quantity

Direction of feed

3000pcs

Reel 1Pin

X XX X

X

XX

X XX X

X

XX

X XX X

X

XX

X X X X X X X

X X X X X X X

MSOP8 <Dimension>

(Unit:mm)

41

58

2.9 ± 0.1

0.475

0.22

0.65

4.0

± 0.

2

0.6

± 0.

20.

29 ±

0.1

5

2.8

± 0.1

0.75

± 0

.05

0.08

± 0

.050.9M

ax.

0.08 S

+0.05−0.04

0.145 +0.05−0.03

0.08 M

Direction of feed

※When you order , please order in times the amount of package quantity.

（Unit:mm)

SSOP-B16 <Dimension>

9

8

16

1

0.1

6.4

± 0.

34.

4 ±

0.2

5.0 ± 0.2

0.15 ± 0.1

0.22 ± 0.10.65

1.15

± 0

.1

0.3M

in.

0.1

<Tape and Reel information>

Tape

Quantity

Direction of feed

Embossed carrier tape

2500pcs

E2 (The direction is the 1pin of product is at the upper left when you hold reel on the left hand and you pull out the tape on the right hand)

Reel Direction of feed 1pin

123

123

123

1234

123

1234

1234

1234

※When you order , please order in times the amount of package quantity.

Tape and Reel information TR

E2

DatasheetDatasheet

Notice - GE Rev.002© 2014 ROHM Co., Ltd. All rights reserved.

Notice Precaution on using ROHM Products

1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment, OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), transport equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications.

(Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA

CLASSⅢ CLASSⅢ

CLASSⅡb CLASSⅢ

CLASSⅣ CLASSⅢ

2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor

products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures:

[a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure

3. Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary:

[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,

H2S, NH3, SO2, and NO2

[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of

flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering

[h] Use of the Products in places subject to dew condensation

4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,

confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability.

7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual

ambient temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in

this document.

Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product

performance and reliability. 2. In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the

ROHM representative in advance. For details, please refer to ROHM Mounting specification

DatasheetDatasheet

Notice - GE Rev.002© 2014 ROHM Co., Ltd. All rights reserved.

Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the

characteristics of the Products and external components, including transient characteristics, as well as static characteristics.

2. You agree that application notes, reference designs, and associated data and information contained in this document

are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information.

Precaution for Electrostatic

This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).

Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where:

[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic

2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period.

3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads

may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of

which storage time is exceeding the recommended storage time period.

Precaution for Product Label QR code printed on ROHM Products label is for ROHM’s internal use only.

Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company.

Precaution for Foreign Exchange and Foreign Trade act Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act, please consult with ROHM representative in case of export.

Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference

only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable for infringement of any intellectual property rights or other damages arising from use of such information or data.:

2. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any

third parties with respect to the information contained in this document.

Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written

consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the

Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons.

4. The proper names of companies or products described in this document are trademarks or registered trademarks of

ROHM, its affiliated companies or third parties.

DatasheetDatasheet

Notice – WE Rev.001© 2014 ROHM Co., Ltd. All rights reserved.

General Precaution 1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.

ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny ROHM’s Products against warning, caution or note contained in this document.

2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior

notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s representative.

3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all

information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or concerning such information.

Documents

BH76330FVM,BH76331FVM,BH76360FV,BH76361FV ...rohmfs.rohm.com/.../video_amplifier/bh76330fvm-e.pdfBH76363FV (6input 1output Video Switch) ・・・・・・P17 No.09065EAT01 Technical