BEYER · PDF fileBEYER GmbH Maschinenbau und Antriebstechnik Safety devices: Emergency power off Safety knife cover Tension is limited when using device for cutting small belts

BEYER GmbHMaschinenbau und Antriebstechnik

37603 HolzmindenLüchtringer Weg 40

Telefon: +49 5531 61025Fax: +49 5531 4237

e-mail: [email protected]


Belt cutting machine type WSM 101 / WSM 102Technical description:

The machine of the type WSM 101 (semi automatic) and WSM 102 (automatic) was engineered for cutting timing and flat belt sleeves. It is especially suitable for processing frequently changing sleeves and profile types with medium to high quantities. All common timing belt profile types can be processed.

Processing dimensions:� Max. belt length 5.800 mm� Min. belt length 130 mm (with device for cutting small belts)� Max. belt width 750 mm

Machine frame:� Stable, welded construction� Delivered as one unit� Affixing of the frame to the floor possible� All linear ducts are made of hardened, grinded steel shafts and ball bearings Tension slide:� Tension of the sleeve is variable min. 3 kp max. 140 kp� Moving of tension slide by drive motor� Angle of tension shaft variable Tool slide:� Semi-automatic processing WSM 101, controlled by PLC� Automatic processing WSM 102, controlled by PLC� Cutting die movement via ball screw driven by drive motor� Digital display of die position, cutting with and number of cuts� Cutting tool is a fixed round die� Tool holder exchangeable� Execution of cutting motion by lever (WSM 101)� Execution of the cutting motion automatically (WSM 102)

Cutting shaft:� Stepless rpm-control via frequency converter from 70 to 450 rpm� Rotation direction changable� Plastic sheath as wearout-cover, Ø 70 mm� Pneumatically triggered holder for supporting the cutting shaft Accessories:� Tool for exchanging the cutting shaft� Tool for exchanging the cutting die� Key for the wiring cabinet� Wiring diagram� Manual


Safety devices:� Emergency power off� Safety knife cover� Tension is limited when using device for cutting small belts� Release of the tension only with closed holder of the cutting shaft� Overload protection of all drive motors

Special equipment:� Device for cutting small belts (min 130 mm in length, up to 450 mm belt width)� Semi-automatic control for the angle of the cutting shaft� Push-on shaft in addition to cutting shaft� Special die unit for cutting poly-v-rip belts� Cutting shaft in special diameters (40 mm, 50 mm, 100 mm)� Standby die (1.6 or 2.2 mm thick, Ø 100 mm)� Tool holder for additional die� Adjustment of the construction to special belt lengths on request� Adjustment of the construction to special belt widths on request

Size of the machine:Length: ca. 3,500 mmWidth: ca. 1,850 mmHeight: ca. 1,250 mm

Power supply:400 Volt, 3 Phases, 50 Hz, 16 AmpereCompressed air: 6 bar

Complete view on WSM 101

Belt cutting machine type WSM 101 / WSM 102


Timing belt cutting machine type WSM 101 / WSM 102Photo gallery:

WSM 101 / WSM 102 Control elements

WSM 101 / WSM 102 Wiring CabinetWSM 101 / WSM 102 Cutting die

WSM 101 / WSM 102 Manual cutting shaftangle control

WSM 101 / WSM 102 Semi-automaticcutting shaft angle control

WSM 101 / WSM 102 Display


Timing belt cutting machine type WSM 101 / WSM 102Photo gallery:

WSM 102 Automatic - Control ElementsWSM 101 / WSM 102 Deflection shafts

WSM 101 / WSM 102 Cutting tool forv-belts WSM 101 / WSM 102 Device for cutting small belts

and special cutting shafts

WSM 101 / WSM 102 Push-on shaft


Belt cutting machine type WSM 100 / WSM 100-B

Technical description:

The machine of the type WSM 101 / WSM 100-B was engineered for cutting timing and flat belt pulleys. It is especially suitable for processing frequently changing sleeves and profile types with low to medium quantities. The WSM 100-B has the same functionality but is using low-cost machine parts. All common timing belt profile types can be processed.

Processing measurements:� Max. belt length 5.800 mm� Min. belt length 130 mm (with device for cutting small belts) � Max. belt width 750 mm

Machine frame:� Stable, welded construction� Delivered as one unit� Affixing of the frame to the floor possible� All linear ducts of the WSM 100 made of hardened, grinded steel shafts and bearing balls

Tension slide:� Tension of the sleeves is variable in 4 levels from 3 kp to 140 kp� Moving of tension slide b drive motor� Angle of tension shaft (Ø 100 mm) variable

Tool slide: � Cutting die movement via manually driven trapezoid screw spindle� Digital display of die position of cutting die� Cutting tool is a fixed round die� Tool holder exchangeable� Execution of the cutting motion via hand lever Cutting shaft:� Stepless variable rpm-control via frequency converter from 70 to 450 rpm� Rotation direction changable� Plastic sheath as wearout-cover, Ø 70 mm� Manual triggered holder for supporting the cutting shaft

Accessories:� Wiring diagram� Manual� Tool for exchanging the cutting shaft� Tool for exchanging the cutting die� Key for the wiring cabinet


Safety devices:� Emergency power off� Safety knife cover� Release of the tightening of the belts only with closed holder

Special equipment:� Semi-automatic control for the cutting shaft angle� Push-on shaft in addition to cutting shaft� Special die for cutting poly-v-rip belts� Cutting shaft in special diameters (40 mm, 50 mm, etc.)� Pneumatically driven retainer for the cutting shaft� Standby knife (1.6 or 2.2mm thick, Ø 100 mm)� Tool holder for additional die Ø 100 mm


Power supply:400 V, 3 Phases, 50 Hz, 16 A

Complete view on WSM 100 / WSM 100-B

Belt cutting machine type WSM 100 / WSM 100-B


Belt cutting machine type WSM 100 / WSM 100-BPhoto gallery:

WSM 100 / WSM 100-B Control elements

WSM 100 / WSM 100-B Wiring Cabinet WSM 100 / WSM 100-B Cutting die

WSM 100 / WSM 100-B Manual cutting shaftangle control

WSM 100 / WSM 100-B Display


Cutting machine type ZSM 150Technical description:

The machine of the type ZSM 150 was engineered for cutting long length timing belts.Single cuts are performed, so the coil is cut along its running direction. All common timing belt profiles can be processed.

Processing measurements:� Max. cutting width 150 mm� Max. coil diameter 1,000 mm

Machine frame:� Stable, welded construction� Delivered as one unit� Affixing of the frame to the floor possible� All linear ducts made of hardened, grinded steel shafts and ball bearings Tool sleigh:� Die movement via manually driven trapezoid spindle� Digital display of die position� Cutting tool is a fixed round die� Die position and cutting depth can be locked

Cutting shaft:� Stepless variable rpm-control via frequency converter� Rotation direction changable� Plastic sheath as wearout-cover for the cutting shaft� Foot switch for processing

Roll-up frame:� Clamping of the sleeve for rolling up� Manual lever for rolling up (automatic rolling up available as special equipment)

Accessories:� Tool for changing the dies� Key for the wiring cabinet� Wiring diagram� Manual Safety equipment:� Emergency power off� Safety die cover� Overload protection for drive motors


complete view ZSM 150

Special equipment:� Automatic rolling up of the processed material� Standby die (thickness: 1.6 or 2.2mm, Ø 100 mm)� Length measurement of the processed material


Power supply:400 V, 3 Phases, 50 Hz, 10 Ampere

Cutting machine type ZSM 150


Cutting machine type ZSM 150Photo gallery:

ZSM 150 Control Elements

ZSM 150 Cutting unit

ZSM 150 Wiring Cabinet


Cutting machine type BSM 120Technical description:

The machine of the type BSM 120 was engineered for cutting timing andflat belts. The machine is especially suited for cutting small numbers ofpieces. Sleeves and long length belts can be cut.

Processing measurements:� Max. cutting width 120 mm� Min. belt length 250 mm

Machine frame:� Stable, welded construction� Delivered as one unit � Insertion of long length belts on the frame� Guide table with edgewise clamped for cutting material Cutting shaft:� Stepless variable rpm-control via frequency converter (2 to 10 m/s)� Rotation direction changable� Distance sleeves between the round dies� Plastic sheath on the counter-pressure shaft� Manually fixation of cutting depth� Fast switch for processing

Accessories:� Tool for exchanging the cutting die� 5 dies� 1 set distance sleeves� Wiring diagram� Manual Safety devices:� Emergency power off� Safety die cover� Tool rest on the frame� Overload protection for the drive motor

Special equipment:� Standby knife (thickness: 2.0 mm, Ø 60 mm)� Additional distance sleeves

Size of the machine:Length: ca. 800 mmWidth: ca. 600 mmHeight: ca. 1,100 mm

Power supply:230 V, 50 Hz, 10 Ampere


Cutting machine type BSM 120Photo gallery:

BSM 120 Complete view

BSM 120 Control elements and sleeves

BSM 120 Cutting shaft

Documents

BEYER · PDF fileBEYER GmbH Maschinenbau und Antriebstechnik Safety devices: Emergency power off Safety knife cover Tension is limited when using device for cutting small belts