Best · PDF fileexceeding the life of the proposed project. Fastener Materials. ... Fastener Design. BEST MATERIALS ® | Email: [email protected] |

Product Guide WEATHER GARDTM

Best MATERIALS.comDiscount Warehouse

webstore

Typewritten Text

webstore

Typewritten Text

BEST MATERIALS ® | Email: [email protected] | www.bestmaterials.com

webstore

Typewritten Text

mailto:[email protected]

http://www.bestmaterials.com

webstore

Typewritten Text


webstore

Typewritten Text



Table of Contents

General Information

Fastener Design ...............................................................3-4

Washer and Fastener Head Styles ................................... 5

Structural Performance ..................................................... 6

Self-Drilling Fasteners

Impax™ Performance Drill Screws ................................... 7

Impax™ Heavy Metal Thickness Structural Drill Screws .................................................. 8

Impax™ Sealer Drill Screws ............................................... 9

Impax™ 1/4" Drill Screws ............................................. 10-11

Impax™ Utility Self-Drill .....................................................12

410 Stainless ...................................................................... 13

Flat Head Utility Self-Drill ................................................ 14

Alloy Capped Fasteners

ZAC® Impax™ 5/16" HWH Alloy Capped ........................ 15

ZAC® Impax™ 3/8" HWH Alloy Capped (for metal to metal) ................................................. 16-17

ZAC® Impax™ 3/8" HWH Alloy Capped (for metal to metal and insulated panel to metal) .............................................................. 18

MAC™ Impax™ Stainless Capped Self-Drill ................... 19

ZAC® Self-Tapping Fasteners .......................................... 20

Prisma™ ............................................................................... 21

Self-Tapping Fasteners

Carbon Steel – Type A, AB, B ....................................22-23

Stainless Steel – Type A, AB, B .................................24-25

Architectural Fasteners (304SS Fasteners)

SX Stainless Self-Drill .................................................26-27

irius® SX Stainless Self-Drill .......................................28-29

SX TORX® Self-Drill .....................................................30-31

TW-S Stainless Self-Tapping (cladding fastener) ....................................................... 32

SLA Stainless Self-Drill (Aluminum composite to aluminum) ............................................. 33

SA6/TDA (Panel fabrication fasteners) .......................... 34

AP Rivet (Cladding panels to aluminum or steel) ....................................................... 35

TU-S Blind Fastener (HPL cladding panel attachment) ........................................................ 36

GAZ Design Elements ...................................................... 37

Metal to Wood

Woodgrip Fasteners ................................................... 38-40

EVERGRIP® Stainless Fasteners ......................................41

Stainless Aluminum Panel Woodgrip ........................... 42

Woodgrip Capped Fasteners .................................... 43-45

Panelmaster® Metal to Wood Fastening System

Panelmaster® Tool & Collated Belted Fasteners ........................................................... 46

Standing Seam Roof Attachment

Standing Seam Panel Clips ........................................47-51

Bearing Plates .................................................................... 52

Clip Fasteners .............................................................. 53-54

Attachment Solutions

AceClamp® - for Standing Seam Roofs ........................ 55

SOL-R - solar attachment for exposed fastener metal roofs .................................... 56

Blind Rivets and Grommets

Blind Rivets ...................................................................57-60

Blind Rivet Tools ..........................................................61-62

Grommet Fasteners .......................................................... 63

Closure, Sealants, Flashings and Venting Products

WG-7™ Closure ................................................................... 64

Pipe Flashing ............................................................... 65-66

ProfileVent® ...................................................................67-68

Ventco™ Ridge Cap Anchor Clip ..................................... 69

Butyl Tape .......................................................................... 70

Hannoband® BG1 Joint Sealant Tape ............................ 71

Novaflex® Metal Roof Sealant ................................... 72-73

Tools and Tool Accessories

Installation Screw Guns and drive sockets ..................................................................74

Panelmaster Tool Kit ........................................................ 46

Blind Rivet Tools ..........................................................61-62

Section PageSection Page

webstore

Typewritten Text


webstore

Typewritten Text



There's More to See.... The fasteners shown are standard products.

Many related, non-standard items are not

shown, but are available and will be priced on

application. We offer a complete selection of

fasteners, closures and accessories. Please

contact us with specific requirements.

A Word About the Specification of FastenersProper fastener selection takes into account where

and how the fasteners are installed. Factors that must

be considered include: materials being attached,

environmental factors, installation conditions, and safety

issues. Because product specifications, applications,

and interpretations may differ, specifiers and purchasers

must make their own product evaluation to be assured of

suitability for the intended use.

Disclosure StatementFastener data shown herein is subject to change or

correction for typographical error without notice. All

test data and ultimate values shown in this catalog are

the result of laboratory testing. Specific job conditions

should be considered and appropriate safety factors

applied when specifying fasteners. In actual applications,

proper installation techniques must be used to assure

adequate performance of the fastener. Assistance and

recommendations are available by contacting your SFS

intec, Inc. sales or customer service professional.

Final selection of fasteners or accessories for use is

ultimately the decision of the purchaser. While SFS

intec, Inc. may assist by providing data and information

for comparison, it makes no suggestions or warranties

pertaining to the suitability of its products for any

particular applicaion.

Galvalume® is a registered trademark of BIEC

International, Inc. TORX® is a registered trademark of

Textron Inc.

webstore

Typewritten Text


webstore

Typewritten Text



Fastener Design

Threaded fasteners for roofing and siding systems are

available in a wide range of materials, designs, and

coatings. When specifying your fastener, be sure to

choose one that has a performance life equaling or

exceeding the life of the proposed project.

Fastener MaterialsCommon Fastener compositions:

• Zinc plated and paint coated carbon steel

• Alloy capped fasteners with zinc-aluminum,

stainless steel, and nylon capped head designs

• Stainless Steel: 300 Series austenitic stainless steel

• Stainless Steel: 400 Series martensitic stainless steel

• Bi-metal: stainless head and threaded shank with a

joint welded hardened carbon steel drill or sharp point

Coated Corrosion-Resistant FastenersSFS intec offers various coating systems such as

electroplating, mechanical plating, and VistaCoat®

Premium System. Zinc serves as a sacrificial coating to

provide cut-edge plating protection.

Metal Alloy Capped FastenersZAC® Zinc Aluminum Capped Head

ZAC design fasteners provide the corrosion resistance

of a zinc-aluminum alloy capped head on a hardened

steel fastener for self-drilling or self-tapping installation.

ZAC is the original capped zinc-aluminum head fastener

and is used in more metal buildings than any other

capped fastener.

ZAC design fasteners are available with a 5/16" and

3/8" capped hex washer head in Impax™ self-drilling

fasteners, Woodgrip™ sheet-to-wood fasteners and

self-tapping screws.

MAC™ 300 Series Stainless Capped Head Self-DrillingFasteners

MAC 300 Series Stainless capped head design combines

the corrosion resistance of stainless steel and a

hardened steel fastener for self-drilling installation. MAC

fasteners are available with a 5/16" capped hex washer

head in Impax self-drilling fasteners and with a 1/4" hex

washer head in Woodgrip fasteners.

Prisma™ Nylon Head Self-Drilling

and Self-Tapping Fasteners

Prisma design fasteners combine the corrosion

resistance of a nylon-molded head with a hardened

steel fastener for self-drilling and self-tapping

installation. The nylon head is formulated with the color

built in. It naturally resists fading and will never rust like

steel headed fasteners. Prisma design fasteners are

available with 3/8" and 7/16" hex washer heads in self-

drillers, Woodgrip metal-to-wood fasteners, and self-

tapping AB fasteners.

Fastener Design

webstore

Typewritten Text




Stainless Steel FastenersA commonly held belief that stainless steel will not rust

or corrode is not necessarily accurate. Stainless steel

is a generic term covering over 200 different types

of alloys that, to varying degrees, corrode less than

carbon steel. It is important that a specifier be aware of

the panel and project performance expectations when

specifying stainless steel fasteners.

Several types of stainless steel are used for fasteners.

300 Series Stainless/Austenitic

• 18-8 stainless alloy with 18% chromium and 8% nickel

• Best known grades are 304 and 316, both work

hardened in the thread-rolling process to manufacture

a self-tapping fastener capable of tapping threads

into steel

• Can be manufactured as a self-drilling, bi-metal

fastener by incorporating a heat-treated hardened

carbon steel drill point joint welded to the austenitic

stainless fastener

• Nonmagnetic

• Provides excellent corrosion resistance compared to

martensitic 410SS fasteners and plated steel fasteners

• Austenitic stainless steel is considered the only type

of stainless steel for panel fasteners

410 Series Stainless/Martensitic

• Stainless alloy with 11.5% to 13.5% chromium

• Can be heat treated to provide hardness to

manu facture as self-tapping or self-drilling

fasteners (when hardened, the part has less

corrosion resistance)

• Poor corrosion resistance compared

to austenitic stainless

• Magnetic

• Plated to improve corrosion resistance

(like carbon steel fasteners)

• Martensitic stainless is not considered

suitable for panel fasteners

Bi-Metal Fasteners

SX Fastener: Austenitic Stainless Self-Drilling Fasteners

SX design fasteners combine the corrosion resistance

of an austenitic 300 series stainless head and threaded

shank with a hardened carbon steel point for self-

drilling installation. These bi-metal fasteners install

like carbon steel fasteners and provide the corrosion

resistance of 18-8 300 series austenitic stainless. SX

fasteners are true stainless steel self-drilling fasteners.

When selecting a stainless steel fastener for any

application where minimizing or virtually eliminating

corrosion is the goal, a specifier should strongly

consider the dramatically greater benefits of 300 series

over 400 series stainless steel fasteners. The richer

chemical composition and SX welded drill point make

300 series stainless steel fasteners more costly, but the

corrosion resistance benefits are far superior.

Fastener Design

webstore

Typewritten Text




Washer Styles

Washer design contributes to the weather seal of a

fastener. SFS offers several washer options based upon

the type of fastener and the application requirements.

Bonded Washer

• EPDM rubber bonded to metal

• Metal washers are available in galvanized

steel, aluminum, and stainless steel

• Bonded washers offer a low-profile appearance

• Provides positive weather seal between

panel and fastener head

Sealer Cupped Hex Washer Head

• EPDM rubber captured under integral

cupped hex head washer

• Cupped washer head prevents overdriving

• EPDM washer and cupped head offers

an excellent weather seal

• EPDM is protected from UV rays

by cupped washer head

Control Seal

• EPDM rubber captured under the stamped “dome”

• Available on all #9 and #12 XG Woodgrip drill screws

• Reinforced domed shoulder distributes clamp load

• EPDM sealant compressed in three key areas

• Weather tight seal even if fastener is driven

in on an angle*

Fastener Head StylesSFS offers a wide variety of fastener head styles

designed to meet your project and fastener

requirements. Each head style will provide proper

panel attachment and desired finish appearance.

Available fastener head styles are:

• irius® drive, low profile

• HWH (hex washer head)

• Cupped hex washer head sealer

• Metal-alloy capped cupped:

HWH ZAC or HWH MAC

• Pancake head

• Low Profile TORX®

• Low Profile Wafer Head

*Proper installation techniques should always be employed.

File

Nam

e: F

D_C

ontr

olS

ealW

ashe

r(2)

.eps

Cre

ated

by:

EW

B-1

2/20

/02

Rev

ised

: MPD

-00/

00/0

2

POS

ITIV

E re

duce

d 00

%

NEG

ATI

VE

redu

ced

00%

File Name: FD00.5_IriusHeadStyle.epsCreated by: EWB-12/10/02

Revised: MPD-00/00/02

POSITIVE reduced 00%

NEGATIVE reduced 00%

File Name: FD00.5_HWH_HeadStyle.epsCreated by: EWB-12/10/02




File Name: FD00.5_HexCupWasherHeadStyle.epsCreated by: EWB-12/10/02




File Name: FD00.5_PancakeheadStyle.epsCreated by: EWB-12/10/02




File Name: FD00.5_ZAC_HeadStyle.epsCreated by: EWB-12/10/02




File Name: FD00.5_MAC_HeadStyle.epsCreated by: EWB-12/10/02




Washer Styles

webstore

Typewritten Text




Fastener and steel gauge sizes used throughout this Weather Gard section are nominal.

Fastener SizesFastener Size #8 #9 #10 #12 #14 #17Thread Diameter Decimal Equivalent .165 .181 .190 .216 .250 .291

Steel Gauge Sizes*

Gauge 30 29 26 24 22 20 18 16 14 12 10Decimal Equivalent .012 .014 .018 .024 .030 .036 .048 .060 .075 .105 .135

* Standard steel thickness used for panels, purlins and girts.

Fasteners are designed to withstand a varied range

of types of loading. Each panel or structural system has

its own specific fastener loading requirements. Care

must be taken to ensure that the appropriate loading

requirements for each application are considered.

Typical structural performance criteria that influence

fastener design include:

Ultimate Tension Strength The point at which a fastener fails under a load exerted in two direct opposite directions.

Typical ultimate tension strengths of each fastener type

are provided on the fastener information pages.

Ultimate Torsion StrengthThe point at which a fastener fails under a twisting load exerted on the head during installation in a torsional direction.

Typical ultimate torsion strengths of each fastener type

are provided on the fastener information pages.

Ultimate Shear Strength The point at which a fastener fails under a load exerted in offset opposing directions, usually upon the shank of the fastener.

Typical ultimate shear strengths of each

fastener type are provided on the fastener

information pages.

Pull-out PerformanceThe ability of a fastener’s threaded connection to remain intact and resist tensile loads.

Self-tapping fasteners require that a pilot hole be

drilled prior to installation. The pullout resistance

will be directly related to the pilot hole diameter.

Self-drilling fasteners have been developed,

and are available, for most steel construction

applications, to a metal thickness of 1/2". This type

of fastener is manufactured with its own integral drill

point, which is engineered to drill the optimum hole

size to facilitate efficient thread forming in the metal

structure, resulting in optimized pullout values.

Pull-over PerformanceThe ability of a fastener to resist the pulling of the fastened sheet material over the head of the fastener due to gravity, wind, or other load.

The resistance to pullover failure is related to the

strength and diameter of the fastener washer and

the strength and thickness of the metal panel.

Structural Performance

Structural Performance

webstore

Typewritten Text




Impax™ — Performance Self-Drill 12-14 Impax and 1/4-14 Impax lap self-drillFor metal to metal


• Precision cold forged assuring superior point strength and the fastest drilling time performance through high strength steel and nested purlins.

• Ultimate performance in light, medium and heavy gage applications.

• Designed and engineered to have low driving and thread engagement torque and provide maximum clamp load.

• Corrosion resistant coating system.

Application12-14 Impax Metal to metalDrilling capacity: .035 – .210Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total.Min projection: 3/16" of threads below substrate

1/4-14 Impax LapPanel to panel side lapDrilling capacity: .030 – .095Some applications may require attaching light gage (24 – 26 ga) to sub-structural member. Composite thickness should not exceed .095.

NotesDimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out values are based on 40,000 psi AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners. #12 fasteners 1" and longer have special long pilot lengths to accommodate nested purlins.

Selection Part No. Part No. Part No. Part No.Length #12 Bond Seal (15 mm) #12 No Washer 1/4-14 Impax Lap w/ Bond Seal 1/4-14 Lap No Washer12-14 x 3/4" V2361-EDF A2361F — —12-14 x 1" V4577-EDF S4577F — —12-14 x 1-1/4" V4632-EDF S4632F — —12-14 x 1-1/2" V4677-EDF S4677F — —12-14 x 2" V4777-EDF S4777F — —12-14 2-1/2" S4902-EDF S4902F — —12-14 x 3" S4952-EDF S4952F — —12-14 x 4" S4981-EDF S4981F — —1/4-14 x 7/8" — — V5051-GUF S5051F

InstallationTools: 0 – 2000 rpm screwdriver equipped with depth sensing nosepiece.

File Name: 304 stainless bimetal.epsCreated by: EWB-11/27/02




5/16" AF Hex Washer Head Thread Major Dia: .246 – .240 Thread Minor Dia: .192 – .185Strength (lbs ult.): Tensile: 3800 Torsional: 150 in-lbs Shear: 2850Pull-out (lbs ult.):- 22 ga (.030): 379 24 ga (.024): 304 26 ga (.018): 204

File Name: WG3._S5051.epsCreated by: EWB-11/11/02

Revised: EWB-00/00/02



5/16" AF Hex Washer Head Thread Major Dia: .215 – .209 Thread Minor Dia: .164 – .157Strength (lbs ult.): Tensile: 2900 Torsional: 92 in-lbs Shear: 2050Pull-out (lbs ult.): 1"– 4" 3/4" 12 ga (.109): 1539 1480 14 ga (.075): 1010 823 16 ga (.060): 724 624Pull-over with Bond Seal (lbs ult.): 22 ga (.030): 1249 24 ga (.024): 1056 26 ga (.018): 654

Painted

ZAC MAC PRISMA irius

ZAC® MAC™ Prisma™ irius Painted Sentri™ BI-METALSX

5 6 7 3 2 1 ?4

StainlessSelf Drilling

File Name: WeatherGard_icons.epsCreated by: EB-11/18/02Revised: MPD-12/02/02

irius



5 6 7 3 2 1 ?4



ZAC®



5 6 7 3 2 1 ?4



MAC™



5 6 7 3 2 1 ?4



OptionsVistaCoat™

webstore

Typewritten Text


webstore

Typewritten Text



Impax™ — Heavy Metal Thickness —Structural Drill Screws

12-24 Impax 4.5 and 5 self-drillFor metal to metal


Application12-24 Impax 4.5 Metal to metalDrilling capacity: .075 – .375Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total. Thread length: 12-24 x 1-1/4": .650Min projection: 3/16" of threads below substrate

12-24 Impax 5Metal to metalDrilling capacity: .075 – .500Thickness is based on normal, single thickness purlin/girt or multiple material thickness.Thread length: 12-24 x 1-1/4": .520 12-24 x 1-1/2": .770 12-24 x 2": 1.020Min projection: 3/16" of threads below substrate

NotesDimensions are nominal inches unless noted. Self-drill pull out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners.

Selection Part No. Part No.Length Bond Seal (15 mm) No Washer

Impax 4.512-24 x 1-1/4" S4661-EDF S4661F

Impax 512-24 x 1-1/4" S4668-EDF S4668F12-24 x 1-1/2" S4741-EDF S4741F12-24 x 2" A2841-EDF A2841F



• Delivers ultimate performance in medium and heavy gage applications.



File Name: WG3.1_S4661.epsCreated by: EWB-11/11/02

Revised: EWB-00/00/02



5/16" AF Hex Washer Head Thread Major Dia: .216 – .210 Thread Minor Dia: .186 – .181Strength (lbs ult.): Tensile: 3450 Torsional: 100 in-lbs Shear: 2420 Pull-out (lbs ult.): 12 ga (.105): 1378 3/16" (.187): Exceeds tensile value 1/4" (.250): Exceeds tensile valuePull-over with Bond Seal (lbs ult.): 22 ga (.030): 1049 24 ga (.024): 861 26 ga (.018): 584





5/16" AF Hex Washer Head Thread Major Dia: .216 – .210 Thread Minor Dia: .186 – .181Strength (lbs ult.): Tensile: 3450 Torsional: 100 in-lbs Shear: 2420 Pull-out (lbs ult.): 12 ga (.105): 1378 3/16" (.187): Exceeds tensile value 1/4" (.250): Exceeds tensile valuePull-over with Bond Seal (lbs ult.): 22 ga (.030): 1049 24 ga (.024): 861 26 ga (.018): 584

Painted



5 6 7 3 2 1 ?4



ZAC®



5 6 7 3 2 1 ?4



MAC™



5 6 7 3 2 1 ?4



webstore

Typewritten Text




Impax™ — Sealer — Drill Screws 12-14 Impax sealer and 1/4-14 lap sealer self-drillFor metal to metal


• Integral cupped Hex Washer Head configuration fastener with an EPDM sealing washer instead of the traditional bonded sealing washer.


• Delivers ultimate performance in light, medium and heavy gage applications.



Application12-14 Sealer ImpaxMetal to metalDrilling capacity: .035 – .210Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total. Min projection: 3/16" of threads below substrate

1/4-14 Sealer Impax LapPanel to panel side lap Drilling capacity: .030 – .095Some applications may require attaching light gage (24 – 26 ga) to sub-structural member. Composite thickness should not exceed .095

NotesDimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out values are based on 40,000 psi AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners. #12 fasteners 1" and longer have special long pilot lengths to accommodate nested purlins.

Selection Part No. Part No.Length #12 Sealer 1/4-14 Sealer Lap12-14 x 3/4" V4486-FGF —12-14 x 1" V4611-FGF —12-14 x 1-1/4" V4636-FGF —12-14 x 1-1/2" V4721-FGF —1/4-14 x 7/8" — V5076-FFF


5/16" AF Cupped Hex Washer Head Thread Major Dia: .215 – .209 Thread Minor Dia: .164 – .157Strength (lbs ult.): Tensile: 2900 Torsional: 92 in-lbs Shear: 2050Pull-out (lbs ult.): 12 ga (.105): 1539 14 ga (.075): 1010 16 ga (.060): 724Pull-over (lbs ult.): 22 ga (.030): 1298 24 ga (.024): 1102 26 ga (.018): 692





5/16 Cupped Hex Washer Head Thread Major Dia: .246 – .240 Thread Minor Dia: .192 – .185Strength (lbs ult.): Tensile: 3800 Torsional: 150 in-lbs Shear: 2850Pull-out (lbs ult.): 22 ga (.030): 379 24 ga (.024): 304 26 ga (.018): 204





Painted



5 6 7 3 2 1 ?4



OptionsVistaCoat™

webstore

Typewritten Text




Impax™ — 1/4" Drill Screws 1/4-14 and 1/4-20 Impax self-drillFor metal to metal



• Impax #2 point is designed with a reduced drill point diameter to provide higher pullout in single purlin attachment.

• Delivers ultimate performance in medium and heavy gage applications.


•Corrosion resistant coating system.

Application1/4-14 Impax HWH #2 Point and #3 PointMetal to metalDrilling capacity: #2 point: .050 – .150 #3 point: .050 – .210Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total. Min projection: 3/16" of threads below substrate

1/4-20 Impax HWH #4 Point Metal to metalDrilling capacity:.060 – .250Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total. Min projection: 3/16" of threads below substrate

NotesDimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners.

#2 – 5/16 AF Hex Washer Head #3 – 3/8" AF Hex Washer Head Thread Major Dia: .246 – .240 Thread Minor Dia: .192 – .185Strength (lbs ult.): Tensile: 3800 Torsional: 150 in-lbs Shear: 2850#2 Point Pull-out (lbs ult.): 12 ga (.105): 2088 14 ga (.075): 1312 16 ga (.060): 903#3 Point Pull-out (lbs ult.): 12 ga (.105): 1697 14 ga (.075): 1151 16 ga (.060): 687Pull-over with Bond Seal (lbs ult.): 22 ga (.030): 1079 24 ga (.024): 884 26 ga (.018): 616





3/8" AF Hex Washer Head Thread Major Dia: .250 – .241 Thread Minor Dia: .200 – .184Strength (lbs ult.): Tensile: 4200 Torsional: 156 in-lbs Shear: 2920Pull-out (lbs ult.): 12 ga (.030): 1913 14 ga (.024): 1061 16 ga (.018): 707Pull-over with Bond Seal (lbs ult.): 22 ga (.030): 1117 24 ga (.024): 988 26 ga (.018): 629

File Name: WG(1.4)_14_20SpecialApp.epsCreated by: EWB-12/13/02




Continued on following page

webstore

Typewritten Text




Impax™ — 1/4" Drill Screws 1/4-14 and 1/4-20 Impax self-drillFor metal to metal


Selection Part No. Part No. Part No. Part No. Part No. Part No. #3 & #4 Point #3 & #4 Point #2 Point Bond Seal #2 Point No Washer #2 Point Bond Seal #2 Point No WasherLength Bond Seal No Washer 5/16" HWH 5/16" HWH 3/8" HWH 3/8" HWH1/4-14 x 3/4" S5010-GBF S5010F — — — —1/4-14 x 1" S5155-GBF S5155F — — S5171-GBF S5171F1/4-14 x 1-1/4" S5201-GBF S5201F S5191-GBF S5191F — —1/4-14 x 1-1/2" S5251-GBF S5251F S5286-GBF S5286F S5271-GBF S5271F1/4-14 x 2" S5351-GBF S5351F — — — —1/4-14 x 2-1/2" S5381-GBF S5381F — — — —1/4-14 x 3" S5451-GBF S5451F — — — —1/4-14 x 4" S5461-GBF S5461F — — — —1/4-20 x 3" #4 Point S5611-GBF S5611 — — — —1/4-20 x 4" #4 Point S5621-GBF S5621F — — — —1/4-20 x 5" #4 Point S5641-GB S5641 — — — —1/4-20 x 6" #4 Point S5661-GB S5661 — — — — 1/4-20 x 7" #4 Point S5671-GB S5671 — — — —1/4-20 x 8" #4 Point S5681-GB S5681 — — — —


Painted



5 6 7 3 2 1 ?4



Options

webstore

Typewritten Text




Impax™


Application8-18 Impax #2 PointDrilling capacity: .035-.140Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total. Min projection: 3/16" of threads below substrate

10-16 #3 Point Drilling capacity: .035-.150Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total. Min projection: 3/16" of threads below substrate

NotesDimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners.

1/4" AF Capped Hex Washer Head Thread Major Dia: .163 Thread Minor Dia: .119Strength (lbs ult.): Tensile: 1575 Torsional: 42 in-lbs Shear: 1035#2 Point Pull-out (lbs ult.): 14 ga (.075): 1084 16 ga (.060): 783 18 ga (.048): 389Pull-over with Bond Seal (lbs ult.): 22 ga (.030): 924 24 ga (.024): 668 26 ga (.018): 421

5/16" AF Hex Washer Head Thread Major Dia: .186 Thread Minor Dia: .138Strength (lbs ult.): Tensile: 1825 Torsional: 48 in-lbs Shear: 1535#3 Point Pull-out (lbs ult.): 12 ga (.105): 1782 14 ga (.075): 1072 16 ga (.060): 782

Selection

Impax 1/4 HWH Self Drill With Bond Seal Without Bond Seal 8-18 x 1/2 HWH SD #2 S1050-BBF S1050F

8-18 x 5/8 HWH NIB SD #2 — S1320F

8-18 x 3/4 HWH SD #2 S1350-BBF S1350F

Impax 5/16 HWH Self Drill With Bond Seal Without Bond Seal 10-16 x 5/8 HWH SD #2 S2401-CDF S2401F

10-16 x 3/4 HWH SD #3 S2701-CDF S2701F

10-16 x 1 HWH SD #3 S3301-CDF S3301F

10-16 x 1-1/4 HWH SD #3 S3601-CDF S3601F

10-16 x 1-1/2 HWH SD #3 S3901-CDF S3901F


Painted



5 6 7 3 2 1 ?4



Options

Utility Self-Drill

• Precision cold forged assuring superior point strength and the fastest drilling time performance.

• Ultimate performance in light and medium gage applications.

• Designed to provide maximum clamp load.• Corrosion resistant coating system.

webstore

Typewritten Text




410 Stainless 12-14 and 1/4-14 lap self-drillFor metal to metal


Application12-14 Stainless SD #3 Point Metal to metal Drilling capacity: .035 – .210Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total.Min projection: 3/16" of threads below substrate

1/4-14 Stainless Lap Panel to panel side lapDrilling capacity: .030 – .095Some applications may require attaching light gage (24 – 26 ga) to sub-structural member. Composite thickness should not exceed .095.

NotesDimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out values are based on 40,000 psi AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners. #12 fasteners 1" and longer have special long pilot lengths to accomodate nested purlins.

5/16" AF Hex Washer Head Thread Major Dia: .215 - .209 Thread Minor Dia: .164 - .157Strength (lbs ult.): Tensile: 2800 Torsional: 92 in-lbs Shear: 1900Point Pull-out (lbs ult.): 12 ga (.109): 1480 14 ga (.075): 823 16 ga (.060): 624Pull-over with Bond Seal (lbs ult.): 22 ga (.030):1249 24 ga (.024): 1056 26 ga (.018): 654

5/16" AF Hex Washer Head Thread Major Dia: .246 - .240 Thread Minor Dia: .192 - .185Strength (lbs ult.): Tensile: 3850 Torsional: 150 in-lbs Shear:2850 Pull-out (lbs ult.): 22 ga (.030): 379 24 ga (.024): 304 26 ga (.018): 204

Selection Part No. Part No. Part No. Part No. Length #12 Bond Seal #12 No Washer 1/4-14 Lap w/ Bond Seal 1/4-14 Lap No Washer12-14 x 3/4" SD3 G0325-FBF G0325F — —12-14 x 1" SD3 G0340-FBF G0340F — —12-14 x 1-1/4" SD3 G0801-FBF G0801F — —12-14 x 1-1/2" SD3 G0810-FBF G0810F — —1/4-14 x 7/8" — — G0773-GWF G0773F


Painted



5 6 7 3 2 1 ?4



Options

• 410 SS is a magnetic heat-treatable stainless steel.

• Type 410 self-drilling fasteners provide fair resistance tocorrosion in mild to light industrial environments.

webstore

Typewritten Text




Flat Head Utility Self-Drill Wood to MetalFor attaching plywood to steel


ApplicationPly Metal Self-Drill 10-24 Wafer Head #2 Phillips Drive

Header Self-Drill with Wings 12-24 Flat Head #3 Phillips Drive

1/4-20 Flat Head Header Self-Drill #3 Phillips Drive

NotesDimensions are nominal inches unless noted. The specific job conditions should be considered and appropriate safty factors applied when specifying the proper fasteners.

Head Dia: .445 Thread Major Dia: .186

• Designed for attaching wood substrates to steel.• Phillips drive and head design for counter sinking.

• More threads per inch for optimum holding power.

Drilling capacity: .060 – .175





SelectionLength Wood Thickness Steel Thickness Part No.10-24 x 3/4" 3/8" plywood .060-.175 A150010-24 x 1" 1/2" plywood .060-.175 A156510-24 x 1-7/16" 3/4" plywood .060-.175 A156712-24 x 2" up to 1" .060-.210 A284412-24 x 2-1/2" up to 1-1/2" .060-.210 A28601/4-20 x 2-3/4" up to 1-3/4" .095-.250 A5085


webstore

Typewritten Text




ZAC® Impax™ — 5/16" HWH Alloy Capped

ZAC 5/16" HWHZinc aluminum capped drill screws

For metal to metal


• ZAC: the most widely used zinc aluminum capped fastener in the industry.


• Integral cupped Hex Washer Head can never red rust. • Designed and engineered to have low driving and thread

engagement torque while providing maximum clamp load.

Application12-14 ZAC (5/16")Metal to metalDrilling capacity: .035 – .210Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total. Min projection: 3/16" of threads below substrate

1/4-14 ZAC Lap (5/16")Panel to panel side lapDrilling capacity: .030 – .095Some applications may require attaching light gage (24 – 26 ga) to sub-structural member. Composite thickness should not exceed .095 thickness.

NotesDimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out values are based on 40,000 psi AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing and we believe typical. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners. #12 fasteners 1" and longer have special long pilot lengths to accommodate nested purlins.

Selection Part No. Part No.Length 12-14 ZAC 1/4-14 ZAC Lap

5/16" AF Hex Washer Head ZAC12-14 x 1" S4591-FLF12-14 x 1-1/4" X4646-FLF —12-14 x 1-1/2" X4731-FLF —12-14 x 2" S4761-FLF —1/4-14 x 7/8" — S5031-FMF






5/16" AF Zinc Aluminum Capped Hex Washer Head Thread Major Dia: .215 – .209 Thread Minor Dia: .164 – .157Strength (lbs ult.): Tensile: 2900 Torsional: 92 in-lbs Shear: 2050Pull-out (lbs ult.): 12 ga (.105): 1539 14 ga (.075): 1010 16 ga (.060): 724Pull-over (lbs ult.): 22 ga (.030): 1647 24 ga (.024): 1310 26 ga (.018): 794

5/16" AF Zinc Aluminum Capped Hex Washer Head Thread Major Dia: .246 – .240 Thread Minor Dia: .192 – .185Strength (lbs ult.): Tensile: 3800 Torsional: 150 in-lbs Shear: 2850Pull-out (lbs ult.): 22 ga (.030): 379 24 ga (.024): 304 26 ga (.018): 204

File Name: 304 stainless bimetal.epsCreated by: EWB-11/27/02




Painted



5 6 7 3 2 1 ?4



OptionsVistaCoat™

webstore

Typewritten Text


webstore

Typewritten Text

webstore

Typewritten Text






For metal to metal

Application12-14 ZAC (3/8")Metal to metalDrilling capacity: .035 – .210Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total.Min projection: 3/16" of threads below substrate.

1/4-14 ZAC Lap (3/8")Panel to panel side lapDrilling capacity: .030 – .095Some applications may require attaching light gage (24 – 26 ga) to sub-structural member. Composite thickness should not exceed .095 thickness.

12-14 x 3/4 ZAC Lap (3/8")Sharp point Panel to panelDrilling capacity .030 – .060Self-piercing points are not designed for attaching light gage (24 – 26 ga) to sub-structural member.

NotesDimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out values are based on 40,000 psi AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners #12 fasteners 1" and longer have special long pilot lengths to accommodate nested purlins.





3/8" AF Zinc Aluminum Capped Hex Washer Head Thread Major Dia: .215 – .209 Thread Minor Dia: .164 – .157Strength (lbs ult.): Tensile: 2900 Torsional: 92 in-lbs Shear: 2050Pull-out (lbs ult.): 12 ga (.105): 1539 14 ga (.075): 1010 16 ga (.060): 724Pull-over (lbs ult.): 22 ga (.030): 1647 24 ga (.024): 1310 26 ga (.018): 794


3/8" AF Zinc Aluminum Capped Hex Washer Head Thread Major Dia: .215 – .208 Thread Minor Dia: .164 – .157Strength (lbs ult.): Tensile: 2100 Torsional: 92 in-lbs Shear: 1800Pull-out (lbs ult.) 22 ga (.030): 538 24 ga (.024): 430 26 ga (.018): 330





File Name: WG5.2_A1653.epsCreated by: EWB-11/27/02







• Integral cupped Hex Washer Head can never red rust. • Designed and engineered to have low driving and thread

engagement torque while providing maximum clamp load.

webstore

Typewritten Text







For metal to metal

Selection Part No. Part No..Length 12-14 1/4-14 Lap)

3/8" Hex Washer Head ZAC12-14 x 3/4" A1653-FLF Sharp Point LAP —12-14 x 1" S4576-FLF —12-14 x 1-1/4" S4631-FLF —12-14 x 1-1/2" S4676-FLF —12-14 x 2" S4776-FLF —12-14 x 2-1/2" S4901-FLF —12-14 x 3" S4951-FLF —1/4-14 x 7/8" — S5065-FMF


Painted



5 6 7 3 2 1 ?4



OptionsVistaCoat™

webstore

Typewritten Text




ZAC® Impax™3/8" HWH Alloy Capped

ZAC® self-drill 3/8" HWHZinc aluminum capped drill screws

For metal to metal and insulated panel to metal




• Designed and engineered to have low driving and thread engagement torque to prevent damage to the cap during installation while providing maximum clamp load.

• Integral cupped Hex Washer Head can never red rust.

Application12-24 ZAC (3/8")4.5 point and 5 point Metal to metalImpax 4.5 Drilling capacity: .075 – .375Impax 5 Drilling capacity: .075 – .500Thickness is based on single thickness purlin/girt or multiple material thickness combined for total.Thread length: ZAC 4.5: 12-24 x 1-1/4": .650 ZAC 5: 12-24 x 1-1/4": .520 12-24 x 1-1/2": .770 12-24 x 2": 1.020Min projection: 3/16" of threads below substrate

Notes Dimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out values are based on 40,000 psi AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners #12 fasteners 1" and longer have special long pilot lengths to accommodate nested purlins.

Selection Part No. Part No. PanelLength 12-14 Insulated 12-24 (4.5 ) and 12-24 (5) Thickness12-24 x 1-1/4" (4.5) — S4665-FLF —12-24 x 1-1/4" (5) — S4669-FLF —12-24 x 1-1/2" (5) — S4742-FLF —


3/8" AF Zinc Aluminum Capped Hex Washer Head Thread Major Dia: .216 – .210 Thread Minor Dia: .186 – .181Strength (lbs ult.): Tensile: 3450 Torsional: 100 in-lbs Shear: 2420Pull-out (lbs ult.): 12 ga (.105): 1378 3/16" (.187): Exceeds tensile value 1/4" (.250): Exceeds tensile valuePull-over with assembled Seal washer (lbs ult.): 22 ga (.030): 1647 24 ga (.024): 1310 26 ga (.018): 794





Painted



5 6 7 3 2 1 ?4



Options

webstore

Typewritten Text

webstore

Typewritten Text




MAC™ Impax™ — 5/16" HWH 300 Series Stainless Capped Self-Drill

MAC stainless capped drill screwsFor metal to metal


• MAC has a 300 series stainless steel capped, integral cupped Hex Washer Head configuration that can never red rust.


Application12-14 MAC Assembled with EPDM washer Metal to metalDrilling capacity: .035 – .210Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total, as in overlapped or nested purlin construction. Min projection: 3/16" of threads below substrate

1/4-14 MAC LapAssembled with EPDM washer Panel to panel side lapDrilling capacity: .030 – .095Some applications may require attaching light gage (24 – 26 ga) to sub-structural member. Composite thickness should not exceed .095 thickness.

12-24 MAC 4.5 Assembled with EPDM washer Metal to metalDrilling capacity: .075 – .375Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total. Nominal thread length: 12-24 x 1-1/4": .650Min projection: 3/16" of threads below substrate

NotesDimensions are nominal inches unless noted. Self-drill pull out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull out values are based on 40,000 PSI AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners. #12 fasteners 1" and longer have special long pilot lengths to accommodate nested purlins.

Selection Part No. Part No. Part No.Length 12-14 MAC 1/4-14 MAC 12-24 MAC12-14 x 1" S4530-FAF — —12-14 x 1-1/4" S4650-FAF — — 12-14 x 1-1/2" S4690-FAF — —12-14 x 2" S4770-FAF — — 1/4-14 x 7/8" — S5100-GGF —12-24 x 1-1/4" (4.5) — — S4672-FAF

5/16” AF Stainless Capped Hex Washer Head Thread Major Dia: .215 – .209 Thread Minor Dia: .164 – .157Strength (lbs ult.): Tensile: 2900 Torsional: 92 in-lbs Shear: 2050Pull-out (lbs ult.): 12 ga (.105): 1539 14 ga (.075): 1010 16 ga (.060): 724Pull-over (lbs ult.): 22 ga (.030): 1298 24 ga (.024): 1102 26 ga (.018): 692





5/16” AF Stainless Capped Hex Washer Head Thread Major Dia: .246 – .240 Thread Minor Dia: .192 – .185Strength (lbs ult.): Tensile: 3800 Torsional: 150 in-lbs Shear: 2850Pull-out (lbs ult.): 22 ga (.030): 379 24 ga (.024): 304 26 ga (.018): 204





5/16” AF Stainless Capped Hex Washer HeadThread Major Dia: .216 – .210 Thread Minor Dia: .186 – .181Strength (lbs ult.): Tensile: 3450 Torsional: 100 in-lbs Shear: 2420 Pull-out (lbs ult.): 12 ga (.105): 1378 3/16" (.187): Exceeds tensile value 1/4" (.250): Exceeds tensile valuePull-over (lbs ult.): 22 ga (.030): 1049 24 ga (.024): 861 26 ga (.018): 584






Painted



5 6 7 3 2 1 ?4



OptionsVistaCoat™

webstore

Typewritten Text




ZAC® 3/8" HWH Alloy Capped Tapping Fasteners

ZAC self-tapping fasteners:AB milled point

For metal to metal


• Integral cupped Hex Washer Head configuration can never red rust. • Designed for attaching both metal to wood and metal to metal.

• Milled points do not require a pre-drilled hole when attaching 26 and 24 gage metal to wood.

Application1/4 -14 ZAC Type AB Milled PointMetal to wood Metal to metalSelf-Drilling Metal Thickness: Sheet .018 – .030Thickness is based on normal, single or multiple material thickness combined for totalMin depth penetration into the wood sub structure: 1"

#17 Zac Type AB Strip-out RepairMetal to metalRepair fastener for stripped out #14 Type A or 1/4" ABMin projection: 3/8" of threads below substrate

NotesDimensions are nominal inches unless noted. When using Milled point fasteners for metal to metal see the tapping screw section for performance values. Pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out values are based on 40,000 psi AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners.

Selection Part No. Part No.Length 1/4-14 AB Length #17 AB

3/8" ZAC1" A4395-FMF 17 x 1" A6045-LFF1-1/2" A4485-FMF 17 x 1-1/2" A6066-LFF2" A4513-FMF2-1/2" A4510-FMF

InstallationTools: Metal to metal application: 0 – 600 rpm screwdriver equipped with depth sensing nosepiece. Metal to wood application: 0 – 2500 rpm screwdriver equipped with depth sensing nosepiece.

3/8 AF Hex Head Thread Major Dia: .290 – .284 Thread Minor Dia: .220 – .214










Painted



5 6 7 3 2 1 ?4



Options

webstore

Typewritten Text


webstore

Typewritten Text



Prisma™Nylon headed fasteners:

self-tapping, self-drill and Woodgrip™For metal to metal and metal to wood

Capped Fasteners

• Prisma nylon head is absolutely corrosion proof.• Nylon head can withstand extreme installation

torque without failure.• Requires no special socket for installation.

• Special washer face allows the fastener to be used on sidewall without a sealing washer.

• Nylon heads are available in 90 standard colours.

Application#14 Type ABMetal to metalSelf-Tapping AB: 1/4-14 x 3/4" 1/4-14 x 1-1/2" 1/4-14 x 2"1/4-14 x 2-1/2"1/4-14 x 3"Stainless AB: 1/4-14 x 3/4"Self-Drill: 1/4-14 x 1" 1/4-14 x 1-3/8" 1/4-14 x 2"Drill capacity: .050 – .210

1/4-14 x 7/8 LapMetal to metalPanel to panel side lap drilling capacity: .030 – .095Self-Drilling Metal Thickness:Thickness is based on normal, single or multiple material thickness combined for total.

#10 WoodgripMetal to wood10 x 1" 10 x 1-1/2" 10 x 2" 10 x 2-1/2" 10 x 3"Min depth penetration into the wood sub structure: 1"

NotesDimensions are nominal inches unless noted. For Type AB metal to metal, see tapping screw section for performance values.

OptionsNone

7/16" Nylon Hex Washer Head1/4-14: Thread Major Dia: .246 – .240 Thread Minor Dia: .192 – .185Strength (lbs ult.): Tensile: 3800 Torsional: 142 in-lbs Shear: 25601/4-14 AB Carbon Steel:Pull-out (lbs ult.): 12 ga (.105): 2185 14 ga (.075): 1277 16 ga (.060): 8791/4-14 #3 Point Carbon Steel:Pull-out: (lbs ult.): 12 ga (.105): 1697 14 ga (.075): 1151 16 ga (.060): 687

7/16" Nylon Hex Washer Head1/4-14: Thread Major Dia: .246 – .240 Thread Minor Dia: .192 – .185Strength (lbs ult.): Tensile: 3800 Torsional: 142 in-lbs Shear: 2560

Woodgrip Prisma 3/8" Nylon Hex Washer HeadThread Major Dia: .199 – .191 Thread Minor Dia: .133 – .127Strength (lbs ult.): Tensile: 1500 Torsional: 60 in-lbs min Shear: 933

File Name: WG5.5_prisma2b.epsCreated by: EWB-12/04/02




File Name: EG5.5_prisma4.epsCreated by: EWB-12/4/02




File Name: WG5.5_prisma1.epsCreated by: EWB-12/04/02




Tapping Screws — Carbon Steel Self-tapping — Type A. AB, BFor metal to metal


• Carbon steel zinc-plated self-tapping fasteners are the original metal construction fastener that can be used in metal to metal and metal to wood applications.

• Tapping screws are available in long lengths for specialty applications.

Application#14 Type AMetal to metalAttachment thickness: .044 – .075Metal thickness Drill bit size .021 – .026 1/8 (.125) .027 – .050 3/16 (.187) .051 – .075 #8 (.199)The hole size determines installation performance and pullout strength.Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total. Min projection: 3/8" of threads below substrate

#14 Type A Milled PointCarbon Steel, Silver Sentri Metal to woodSelf-drilling metal thickness: Sheet .018 – .030Thickness is based on normal, single or multiple material thickness combined for total.Min depth penetration into the wood sub structure: 1"

1/4 Type AB and BMetal to metalAttachment thickness: .044 – .500 Metal thickness Drill bit size AB .021 – .026 1/8 (.125) AB .027 – .050 5/32 (.156) AB .051 – .075 #8 (.199) AB .075 – .110 #7 (.201) B .065 – .085 #8 (.199) B .085 – .115 #7 (.201) B .115 – .375 #1 (.228) B .375 – .500 #1 or larger, depending on hardness of steel Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total. Min projection: 3/8" of threads below substrate

NotesDimensions are nominal inches unless noted. Pull-out values (pounds ultimate) are based on 50,000 psi hot rolled steel sheet material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners.

3/8" AF Hex Head Thread Major Dia: .254 – .248 Thread Minor Dia: .185 – .178Strength (lbs ult.): Tensile: 3500 Torsional: 125 in-lbs Shear: 2400Pull-out (lbs ult.): 14 ga (.075): 1318 16 ga (.060): 958 18 ga (.048): 605Pull-over (lbs ult.): 22 ga (.030): 1097 24 ga (.024): 810 26 ga (.018): 564





3/8" AF Hex Head Thread Major Dia: .246 – .240 Thread Minor Dia: .192 – .185Strength (lbs ult.): Tensile: 3800 Torsional:142 in-lbs Shear: 2560Pull-out (lbs ult.): 12 ga (.105): 2185 14 ga (.075): 1277 16 ga (.060): 879Pull-over (lbs ult.): 22 ga (.030): 1094 24 ga (.024): 866 26 ga (.018): 600






5/16" AF Hex Washer Head Thread Major Dia: .254 – .248 Thread Minor Dia: .185 – .178Strength (lbs ult.): Tensile: 3500 Torsional: 125 in-lbs Shear: 2400Pull-out (lbs ult.): 1" SPF wood: 1013Pull-over (lbs ult.): 22 ga (.030): 1097 24 ga (.024): 810 26 ga (.018): 564





Application#17 Type ABStrip out repair Type A or AB Metal to metalAttachment thickness: .036 – .060Min projection: 3/8" of threads below substrate



Tapping Screws — Carbon Steel Self-tapping — Type A. AB, BFor metal to metal

SelectionPart No. Part No. Part No. Part No.

Length* #14 A Bond Seal #14 A Milled Point Bond Seal 1/4 AB & #17 AB Bond Seal 1/4 B Bond Seal3/4" A2980-GB — A4320-GB A3800-GB1" A3240-GB V3321-GBF A4420-GB A3860-GB1-1/4" A3420-GB — A4440-GB —1-1/2" A3460-GB V3438-GBF A4500-GB A3920-GB2 " A3520-GB V3531-GBF — A4000-GB2-1/2" A3580-GB A3597-GBF — A4040-GB3" A3620-GB A3626-GBF — A4080-GB3-1/2" A3640-GB — — A4140-GB4" A3680-GB — — A4220-GB5" A3720-GB — — A4260-GB6" A3740-GB — — A4280-GB#17 x 3/4" — — A6020-KJ —#17 x 1" — — A6040-KJ —#17 x 1-1/2" — — A6060-KJ —

*Longer lengths available upon request

InstallationTools: 0 – 1000 rpm on type B screwdriver equipped with depth sensing nosepiece.

ZAC®



5 6 7 3 2 1 ?4



Painted



5 6 7 3 2 1 ?4



OptionsVistaCoat™

3/8" AF Hex Head Thread Major Dia: .295 – .285 Thread Minor Dia: .220 – .214





(RH2) Product Name: #14 (RH3) Description: #3 Phillips Drive(RH4) Application: Insulation board to roof cover.

Tapping Screws — 300 Series Stainless Steel

Stainless self-tapping — Type A, AB, BFor metal to metal


• Stainless steel zinc-plated self-tapping fasteners are designed for attaching metal to metal and metal to wood.

• Type B have wax surface treatment for added lubricity.

• Stainless tappers are used in high corrosive environments or where corrosions free performance is required to meet the design life of the project.

Application#14 Type A 304 StainlessMetal to metalAttachment thickness: .044 – .075 Metal thickness Drill bit size .021 – . 026 1/8 (.125) .027 – . 050 3/16 (.187) .051 – . 075 #8 (.199)The hole size determines installation performance and pullout strength.Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total. Min projection: 3/8" of threads below substrate

Type AB and B 304 StainlessMetal to metalAttachment thickness: .044 – .500Metal thickness Drill bit size AB .021 – .026 1/8 (.125) AB .027 – .050 5/32 (.156) AB .051 – .075 #8 (.199) AB .075 – .104 #7 (.201)B .065 – .085 #8 (.199) B .085 – .115 #7 (.201) B .115 – .375 #1 (.228) B .375 – .500 #1 or larger, depending on hardness of steel Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total. Min projection: 3/8" of threads below substrate

#17 Type AB 304 StainlessStrip out repair Type A or AB Metal to metalMin projection: 3/8" of threads below substrate


3/8" AF 304 Stainless Hex Head Thread Major Dia: .254 – .248 Thread Minor Dia: .185 – .178Strength (lbs ult.): Tensile: 3370 Torsional: 125 in-lbs Shear: 1520Pull-out (lbs ult.) 14 ga (.075): 1232 16 ga (.060): 1110Pull-over (lbs ult.): 22 ga (.030): 1237 24 ga (.024): 790 26 ga (.018): 647

File Name: WG7.2_E0600.epsCreated by: EWB-11/27/02




3/8" AF 304 Stainless Hex Head Thread Major Dia: .246 – .240 Thread Minor Dia: .192 – .185Strength (lbs ult.): Tensile: 3800 Torsional: 142 in-lbs Shear: 2350Pull-out (lbs ult.): 12 ga (.105): 2310 14 ga (.075): 1394 16 ga (.060): 1250Pull-over (lbs ult.): 22 ga (.030): 1237 24 ga (.024): 790 26 ga (.018): 647

3/8" 304 Stainless AF Hex Head Thread Major Dia: .295 – .285 Thread Minor Dia: .220 – .214











Tapping Screws — 300 Series Stainless Steel

Stainless self-tapping — Type A, AB, BFor metal to metal

Selection Part No. Part No. Part No.Length #14 A Bond Seal 1/4 AB & #17 AB Bond Seal 1/4 B Bond Seal3/4" E0500-HP E1240-HP E0860-HPW1" E0600-HP E1300-HP E0880-HPW1-1/4" E0640-HP E1310-HP —1-1/2" E0660-HP E1320-HP E1000-HPW2" E0700-HP — E1060-HPW2-1/2" E0720-HP — E1080-HPW3" E0740-HP — E1100-HPW3-1/2" E0760-HP — E1120-HPW4" E0780-HP — E1140-HPW5" E0820-HP — E1180-HPW6" E0840-HP — E1200-HPW7" E0850-HP — E1210-HPW8" E0855-HP — E1215-HPW#17 x 3/4" — E1960-KP —#17 x 1" — E1980-KP —#17 x 1-1/2" — E2000-KP —


OptionsPainted



5 6 7 3 2 1 ?4



SX Stainless Self-Drill SX austenitic stainless steelFor metal to metal

ApplicationSX3 Self-Drill5/8" O.D Stainless Bond SealMetal to metalDrill capacity: .035 – .098

SX5 Self-Drill5/8" O.D Stainless Bond SealMetal to metalDrill capacity: .060 – .157

SX14 Self-Drill5/8" O.D Stainless Bond SealMetal to metalDrill capacity: .157 – .550

SL2-S Free Spin Lap Self-Drill1/2" (14mm) O.D. for #125/8" (16mm) O.D. for #14 Stainless Bond SealMetal to metalDrill capacity: .031 – .079

5/16" AF Hex Washer Head Dia: Nominal #12Strength (lbs ult.): Tensile: 2735 Torsional: 70 in-lbs Shear: 2240Pull-out (lbs ult.): 12 ga (.105): 1399 14 ga (.075): 795 16 ga (.060): 582Pull-over (lbs ult.): 24 ga (.024): 1190 26 ga (.018): 665

5/16" AF Hex Washer Head Dia: Nominal #14Strength (lbs ult.): Tensile: 2535 Torsional: 70 in-lbs Shear: 1864Pull-out (lbs ult.): 12 ga (.105): 1125 14 ga (.075): 855 16 ga (.060): 610Pull-over (lbs ult.): 24 ga (.024): 1300 26 ga (.018): 705

5/16" AF Hex Washer HeadDia: Nominal #12Strength (lbs ult.): Tensile: 2695 Torsional: 70 in-lbs Shear: 2695Pull-out (lbs ult.): 12 ga (.105): 1220 3/16" (.187): Exceeds tensile value 1/4" (.250): Exceeds tensile valuePull-over (lbs ult.): 24 ga (.024): 1150 26 ga (.018): 646

5/16" AF Hex Washer Head Dia: Nominal #14Strength (lbs ult.): Tensile: 3740 Torsional: 70 in-lbs Shear: 2790


• SX Austenitic stainless fasteners come with a Bi-metal welded carbon steel point.

• SX Austenitic stainless product line offers fastening solutions for attaching panels from very thin to 1/2" structural steel.

• Provides ultimate corrosion performance for attaching steel, stainless or aluminum panels.

• Designed for secured attachment to both panel and substructures.

• Stainless self-drill fasteners are engineered to have low driving torque and provide maximum clamp load.

• Ultimate drill performance in light, medium, and heavy gage applications.

• Washer O.D designed for both sidewall and roof panel attachment.


Architectural Fasteners

SX Stainless Self-Drill SX austenitic stainless steelFor metal to metal

Application continuedSXC14 Self-Drill Standoff3/4" O.D Stainless Bond SealInsulated panel to metal#5 PointDrill capacity: .157 – .551

SXCW Self-Drill3/4" O.D Stainless Bond SealInsulated panel to woodDrill capacity: .031 – .079


5/16" AF Hex Washer Head Dia: Nominal 1/4"Strength (lbs ult.): Tensile: 3934 Torsional: 95 in-lbs Shear: 2450

OptionsPainted



5 6 7 3 2 1 ?4



irius



5 6 7 3 2 1 ?4



Selection Part No. Part No. Part No. Part No. Length Bond Seal No Washer Length Bond Seal No Washer SX3 Self-Drill Stainless HWH SX14 Self-Drill Stainless HWH 14-11 x 1-1/8 SD 1141978 1141971 12-14 x 1-9/16 SD 5 0770785 0770786 14-11 x 1-1/2 SD 1133237 1142006 12-14 x 1-7/8 SD 5 0773625 0773627 14-11 x 2 SD 1133239 1142057 12-14 x 2-1/2 SD 5 0770805 0770804 SX5 Self-Drill Stainless HWH 12-14 x 3-1/4 SD 5 0523277 0526400 12-14 x 1-1/4 SD 1122767 1134304 12-14 x 4 SD 5 0768379 0777580 12-14 x 1-1/2 SD 1123168 1133976 Part No. Panel 12-14 x 1-5/8 SD 1134477 1134478 Length Bond Seal Thickness 12-14 x 2-1/8 SD 1133684 1154328 SXC14 Self-Drill 12-14 x 3-1/8 SD 1133330 1133309 12-14 x 3-1/8" 0773620 1-1/2" — 1-7/8" 12-14 x 3-3/4 SD 1141958 1141957 12-14 x 3-3/4" 0775732 1-7/8" — 2-1/2" 12-14 x 4-1/4 SD 1141963 1141962 12-14 x 4-5/8" 0776324 2-5/8" — 3-5/16" 12-14 x 5-1/2 SD 1141967 1141966 12-14 x 5-1/2" 0768491 3-5/16" — 4-1/8" SL2 Lap Self-Drill Stainless HWH 12-14 x 6-5/8" 1185167 4-1/8" — 5-5/16" 12-11 x 1 Lap SD 1123164 1133482 SXCW Self-Drill 1/4-14 x 1-1/8 Lap SS 1133512 - 14 x 3-1/2" 0998230 1-1/8" — 1-7/16" 14 x 4-1/8" 0997836 1-1/2" — 2-1/8" 14 x 4-9/16" 0998241 1-7/8" — 2-9/16" 14 x 5-3/8" 0997821 2-5/8" — 3-5/16" 14 x 6-1/4" 0997840 3-1/16" — 4-1/8"



irius® SX Stainless Self-Drill irius SX austenitic stainless steelFor metal to metal

• irius is a patented drive system available on a full range of metal building fasteners.

• irius SX stainless fasteners’ low profile head that has changed the future architectural appearance of sidewall fastening.

• Fastening system drive socket insures positive engagement and prevents damage to a painted fastener head.

• Self-drilling point design assures superior point strength and the excellent drill performance through high strength steel.

• Stainless fasteners provide the ultimate corrosion performance for attaching steel, stainless or aluminum panels.

• SX austenitic stainless self-drill fasteners are engineered to have low driving torque and provide maximum clamp load.

ApplicationSX 3-L12 irius Self-Drill1/2" O.D Aluminum Bond SealMetal to metalDrill capacity: .035 – .098

SX 5-L12 irius Self-Drill1/2" O.D Aluminum Bond SealMetal to metalDrill capacity: .060 – .157

SX 14-L12 irius Self-Drill5/8" O.D Stainless Bond SealMetal to metalDrill capacity: .157 – .550

SL2-S-L12 irius Free Spin Lap Self-Drill1/2" or 5/8" O.D Stainless Bond SealMetal to metalDrill capacity: .031 – .079

irius low profile and drive system Dia: Nominal #14Strength (lbs ult.): Tensile: 2535 Torsional: 70 in-lbs Shear: 1864Pull-out (lbs ult.): 12 ga (.105): 1125 14 ga (.075): 855 16 ga (.060): 610Pull-over (lbs ult.): 24 ga (.024): 1300 26 ga (.018): 705

irius low profile and drive system Dia: Nominal #12Strength (lbs ult.): Tensile: 2735 Torsional: 70 in-lbs Shear: 2240Pull-out (lbs ult.): 12 ga (.105): 1399 14 ga (.075): 795 16 ga (.060): 582Pull-over (lbs ult.): 24 ga (.024): 1190 26 ga (.018): 665

irius low profile and drive system Dia: Nominal #12Strength (lbs ult.): Tensile: 2695 Torsional: 70 in-lbs Shear: 2695Pull-out (lbs ult.): 12 ga (.105): 1220 3/16" (.187): Exceeds tensile value 1/4" (.250): Exceeds tensile valuePull-over (lbs ult.): 24 ga (.024): 1150 26 ga (.018): 646

irius low profile and drive system Dia: Nominal #12Strength (lbs ult.): Tensile: 1670 Torsional: 70 in-lbs Shear: 1370

File Name: WG3_SX14.epsCreated by: EWB-12/19/02



NEGATIVE reduced 00% Continued on following page


irius® SX Stainless Self-Drill irius SX austenitic stainless steelFor metal to metal

OptionsPainted



5 6 7 3 2 1 ?4



Selection Part No. Part No. Length Bond Seal No Washer SX3-L12 irius Self-Drill 14 x 1-1/8 SD 1142002 1142001 14 x 1-1/2 SD 1196328 1142030 SX5-L12 irius Self-Drill 12-14 x 1-1/4 SD 1134345 1134342 12-14 x 1-1/2 SD 1134359 1134355 12-14 x 1-5/8 SD 1135437 1135452 12-14 x 2-1/8 SD 1144693 1241511 SX14-L12 irius Self-Drill 12-14 x 1-9/16 SD 0776328 0776332 SL2-L12 irius Free Spin Lap Self Drill 1/4-14 x 1 Lap SD 14mm SS Bond Seal 1135477 1/4-14 x 1 Lap SD 16mm SS Bond Seal 1147314

InstallationTools: 0 – 2000 rpm screwdriver equipped with depth sensing nosepiece.The E420 irius drive socket (part #0973316) is required.


• SX Austenitic stainless fasteners come with a Bi-metal welded carbon steel point.

• SX Austenitic stainless product line offers fastening solutions for attaching panels from very thin to medium gage applications.

• Provides ultimate corrosion performance for attaching steel, stainless or aluminum panels.

• Low profile TORX drive for aesthetic installed appearance

• Designed for secured attachment to both panel and substructures.

• Stainless self-drill fasteners are engineered to have low driving torque and provide maximum clamp load.

• Ultimate drill performance in light and medium gage applications.

ApplicationSX 3-D10 TORX® Self-DrillMetal to metalDrill capacity: .039 –.118”

SX 5-D12 TORX® Self-Drill1/2" O.D Aluminum Bond SealMetal to metalDrill capacity: .060–.157”

SL2-S-D12 Lap TORX® Self-Drill3/8” O.D. Aluminum Bond SealMetal to metalDrill capacity: .060”

NotesDimensions are nominal unless noted. The specific job conditions should be considered and appropriate safty factors applied when specifying the proper fasteners.

Drive TORX® T20WHead Dia .404-.384”Thread Major Dia .189-.183”Thread Minor Dia .141-.135”Strength (ult.): Tensile: 1960 lbs Shear: 1456 lbsPull-out (ult.): 12 ga (.105): 1189 lbs 14 ga (.075): 854 lbs 16 ga (.060): 696 lbs

Drive TORX® T-25Head Dia .482 - .462”Thread Major Dia .215 - .211”Thread Minor Dia .164 - .157”Strength (ult.): Tensile: 2735 lbs Torsional: 2240 lbs Shear: 70 lb-inPull-out (ult.): 12 ga (.105): 1399 lbs 14 ga (.075): 795 lbs 16 ga (.060): 582 lbs

Drive TORX® T20WHead Dia .482 - .462”Thread Major Dia .216 - .208”Thread Minor Dia .134 - .126”Strength (ult.): Tensile: 1670 lbs Torsional: 70 lb in Shear: 1370 lbsPull-out (ult.): 16 ga (.060): 902 lbs18 ga. (.048): 668 lbs

SX TORX® Self-Drill SX austenitic stainless steelFor metal to metal



SX TORX® Self-Drill SX austenitic stainless steelFor metal to metal

Selection Part No. Part No. Length Bond Seal No Washer

SX3-D10 TORX®

10-16 x 1 SD T20W — 119354712-11 x 1-3/16 SD T25 — 1235148SX5-D12 TORX®

12-11 x 1-1/2 SD 1133806 1133805SL2-S-D12 Lap TORX®

12 x 1 LAP SD 1135881 1137560

InstallationFasteners should provide for a minimum of 3 fully developed threads through the metal substrate.Tools: 0-2000 rpm screwdriver equipped with depth sensing nosepiece.T20W or T25 TORX drive bit.

OptionsPainted



5 6 7 3 2 1 ?4




• Aesthetic fastening system for attaching cladding panels to timber battens, aluminum and steel framework.

• Low profile TORX® drive head can be colored to match any cladding panel.

• 304 Stainless Steel provides maximum resistance to corrosion.

ApplicationTW-S-D12 #10-12 Self-TappingCladding Panel to Wood

Material: 304 Austentic Stainless Steel

TW-S-D13 #12-11 Self-TappingCladding Panel to Metal

Material: 304 Austentic Stainless Steel

Notes: Dimensions are nominal unless noted. The specific job conditions should be considered and appropriate safety factors applied when specifyng the proper fasteners.

Drive: TORX® T20WHead Dia: .492 - .453”Thread Major Dia: .194 - .188”Thread Minor Dia: .134 - .129”Nom. Tensile: 1596 lbsMin. Torsional: 60 lb-inNom. Shear: 1213 lbs

Pull-out Strength - SYP Dimensional Lumber1/4”: 481 lbs

Pull-out Strength - Plywood3/4”: 578 lbs 5/8”: 438 lbs 1/2”: 348 lbs

Pull-out Strength - OSB (Oriented Strand Board) 23/32”: 449 lbs19/32”: 412 lbs7/16”: 228 lbs

Drive: TORX® T20WHead Dia: .531” - .493”Thread Major Dia: .221” - .215”Thread Minor Dia: .162” - .155”

Nom. Tensile: 2144 lbsMin. Torsional: 65 lb-in Nom. Shear: 2200 lbs

Pull-out Strength - Extruded Aluminum1/8”: 800 lbs pre-drill: 13/64 (.203”)1/4”: 1800 lbs pre-drill: 13/64 (.203”)

Pull-out Strength - 55 KSI Yield Sheet Steel 16 ga. (.060”) 637 lbs pre-drill: 3/16 (.187”)

TW-S Stainless Self-Tapping

Selection Description Part No. Global CodeTW-S-D1210-12 x 1 0902988 TW-S-D12-4,8X2510-12 x 1-1/8 0062661 TW-S-D12-4,8X3010-12 x 1-1/2 0625848 TW-S-D12-4,8X3810-12 x 1-3/4 0698813 TW-S-D12-4,8X4410-12 x 2-3/8 0055443 TW-S-D12-4,8X60TW-S-D1312-11 x 1 0705260 TW-S-D13-5,5X2512-11 x 1-1/8 0759330 TW-S-D13-5,5X2912-11 x 1-1/2 0705261 TW-S-D13-5,5X38

InstallationFastener length should provide for a minimum of 1” penetration into wood substrate.Fastener length should provide for a minimum of 3/16” penetration of fully developed threads into metal substrate. Check with cladding panel manufacturer for specific installation guidelines.

Tools: 0-2500 rpm screwdriver with depth sensing nosepiece.T20W TORX drive bit.

Fastening cladding to timber battens, aluminum and steel framework

OptionsPainted



5 6 7 3 2 1 ?4




SLA Self-Drill

• 304 austenitic stainless steel provides the optimum corrosion resistance performance.

• TORX® T20W drive makes installaton fast and easy.

• Resistant to overdrive.

• Resistant to back out.

• Low profile provides for an aesthetically pleasing façade.

• Custom color matching to your panel is available with scratch resistant coating

ApplicationSLA3 Self-Drill Aluminum composite panels to aluminum frameworkDrilling Capacity (Aluminum): .071”-.118”

Material: 304 Austentic Stainless Steel A2,material number 1.4301, AISI 304


Drive: TORX® T20WHead Dia: .470”Dia Nominal: .190”

Tensile: 1765 lbsShear: 1177 lbs

Pull-out StrengthAlMg 1.8 mm (.07l”): 440 lbsAlMg 2 mm (.079”): 517 lbs

Selection Description Part No. Global Code Grip Range10-16 x 3/4" SD2 1025055 SLA3/6 S-D12-4,8X19 0.236"

Installation0-2500 rpm screwdriver equipped with depth sensing nosepiece.T20W TORX® drive bit.

Fastening aluminum compositepanels to aluminum

OptionsPainted



5 6 7 3 2 1 ?4




SA6/TDA Panel Fabrication Fasteners

• 304 austenitic stainless steel• Ensures compatability between fastener, panel and framework

ApplicationSA6 PHL Pan Head#10-16 Self-Drill Panel to Aluminum Aluminum to AluminumDrilling capacity: Max .118”

Material: 304 Austenitic Stainless Steel

SA6 PHL Flat Head #10-16 Self-DrillPanel to Aluminum Aluminum to AluminumDrilling capacity: .196-.035” Material: 304 Austenitic Stainless Steel

TDA PHL Flat Head #10 Self-Tapping Type A Cladding Panel to Metal Metal to Metal

Material: 304 Austenitic Stainless Steel

Notes: Dimensions are nominal unless noted. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners.

Drive: #2 Philips Head Dia: .346” Thread Major Dia: .185” Thread Minor Dia: .132”Strength (ult.): Tensile: 1760 lbs Torsional: 55 in-lbs Shear: 1182 lbsPull-out Strength - Extruded Aluminum: 1/8” (.125”): 823 lbs

Drive: #2 Philips Head Dia: .346” Thread Major Dia: .185” Thread Minor Dia: .132”Strength (ult.): Tensile: 1760 lbs Torsional: 55 in-lbs Shear: 1182 lbsPull-out Strength - Extruded Aluminum: 1/8” (.125"): 920 lbs pre-drill #21 (.159”)

Drive: #2 Philips Head Dia: .365” Thread Major Dia: .182” Thread Minor Dia: .134”Strength (ult.): Tensile: 1420 lbs Torsional: 50 in-lbs Shear: 1270 lbsPull-out Strength - Aluminum .057” Aluminum: 465 lbsAssembled Shear Strength 1/8” Alum. Bracket to .057” Alum 687 lbs

Selection Description Part No. Global CodeSA6 PHL Pan Head #10 x 3/4" 1269126 SA6/6-D9-PH2-4,8X19SA6 PHL Flat Head#10 x 3/4" 1247521 SA6/6-PH2-4,8X19#10 x 1" 1247449 SA6/11-PH2-4,8X25TDA PHL Flat Head#10 x 3/4" Type A 1247525 TDA-S-PH2-4,8X19#10 x 1" Type A 1247523 TDA-S-PH2-4,8X25

InstallationFasteners should provide for a minimum of 3 fully developed threads through the metal substrate.Tools: 0-2000 rpm screw driver equipped with depth sensing nosepiece.


• Can be used in assemblies of dissimilar materials, thick and thin, hard and soft, metal, composites and phenolic panels

• Good installed appearance

• Tamper resistant

• Won’t loosen in high vibration and fatigue applications

• Reliable quality and repeatability of assembly

• No over-driving or under-driving

• Available painted to match any panel color

ApplicationAP16 Rivet Attach high-performance cladding panels to aluminum or steel sub-framesDrilling capacity:

Material:Body: Aluminum AlMg5Mandrel: Stainless Steel A3

Notes: Dimensions are nominal unless noted. The specific job conditions should be considered and appropriate safety factors applied when specifyng the proper fasteners. Pull-out strength values obtained with 5.1 mm (0.201”) pre-drill.

16(0.63”)

2.7(0.11”)

1.5 (0.06”)

5 (0.19”)

Nom. Tensile: 3720 N (836 lbs.) Pull-out Strength - Extruded Aluminum Pull-out Strength - 33 KSI Yield Sheet SteelNom: Shear: 2410 N (542 lbs.) AIMg 1.8mm (.071”): 2410 N (542 lbs) 22 ga. (030”): 1210 N (272 lbs.) 18 ga. (.048”): 2360 N (530 lbs.)

AP Rivet Fastening cladding panels to aluminumor steel framework

Selection Description Part No. Global Code Grip Range5 X 16mm 0914963 AP16-50160-S 8.0-12.0 mm (.314-.472")5 X 18mm 0870920 AP16-50180-S 9.5-13.5 mm (.374-.531")5 X 21 mm 0994642 AP16-50210-S 12.5-16.5 mm (.492-.649")

Installation5.1mm (0.201”) pilot hole required in aluminum framework for fixed point. All other holes depend on material. Check the attachment method instructions provided by the cladding panel manufacturer.

OptionsPainted



5 6 7 3 2 1 ?4




TU-S Blind Fastener Fastening HPL cladding panels

• Enables brackets, straps or clips to be attached quickly and securely to the back of HPL cladding panels

• Cost-effective

• Installation can be performed by one person

• No special tools required

• Can be installed into panels 8mm to 13mm (.31” to .51”) thick

ApplicationTU-S Blind Fastener Fasten brackets, straps or clips to the back of panels

Material:Sleeve: Stainless steel (grade 316, DIN 1.4401)

Mandrel: Carbon steel (is pulled off completely, i.e. no residue remains)


3.3 (0.13”)

6 (0.24”)

8(0.31”)

Selection Description Part No. Global Code Bracket Range Panel Range6 X 11mm 0778444 TU-S-6X11 0.5-5.5 (0.02-0.21") 8-13 mm (0.31-0.51")6 X 13mm 0848724 TU-S-6X13 2.5-7.5 (0.09-0.29") 10-13 mm (.039-0.51")

InstallationPre-drill pilot hole a minimum of 6.5mm deep and 6.0mm diameter. Residual panel thickness must be at a minimum of 1.5mm; check panel manufacturer’s specific requirements. Insert fastener by hand through bracket into pre-drilled pilot hole; remove the mandrel with riveting tool.

Utilize HSS blind hole drill bit, 6mm (0.236”) diameter, with depth stop

Bracket or clips requires a 7 mm (0.276”) clearance hole

An appropriate washer is required with thinner brackets.


GAZ Design Elements Exposed fastening effects forcladding attachment

GAZ Design Elements fasteners are a two-part fastening system. The 304SS anchor secures cladding to timber, steel or aluminum sub-frames. The design element cap is then effortlessly assembled on to the special fastener after installation.

• 300 series stainless steels provides maximum corrosion resistance

• Design elements available in a choice of colors and fascinating effects

• Creates special emphasis on internal or external surfaces

• Secure against unwinding through dynamic loads. Cannot be removed manually after curing.

ApplicationGA #14 Type A Anchor

Material:Fastener: 304SSSealing Washer: SS with vulcanized EPDM

GA #14 Type B Anchor

Material:Fastener: 304SSSealing Washer: SS with vulcanized EPDM

GAZ Design Element Caps Available in 316 Stainless Steel, 303 Stainless Steel or anodized aluminum

Available in the following colors:Stainless Steel: Mill finish, 40 maximum surface roughnessAluminum: red, blue, green, black, gold, silver

8010.865” x 1.26”

8040.865” x 1.26”

8061.24” x 1.50”

8071.24” x 1.26”

8110.865” x 1.26”

SW 9.5 (0.38”)

6.5 (0.26”)

45 (1.77”)

SW 9.5 (0.38”)

6.3 (0.25”)

32 (1.26”)

Selection Part No. Description Global CodeAnchors0006132 14 x 1-1/4 Type A Stainless Steel Anchor GA-AS-S16-6,5X320921058 14 x 1-3/4 Type A Stainless Steel Anchor GA-AS-S16-6,5X450920499 14 x 1-1/4 Type B Stainless Steel Anchor GA-BS-S16-6,3X32GAZ Design Elements0974222 Stainless Steel Cap GAZ-801-S0984140 Stainless Steel Cap GAZ-804-S0920496 Stainless Steel Cap GAZ-806-S0920497 Stainless Steel Cap GAZ-807-S0974609 Stainless Steel Cap GAZ-811-S000000 Anodized Aluminum Cap GAZ-801000000 Anodized Aluminum Cap GAZ-804000000 Anodized Aluminum Cap GAZ-806000000 Anodized Aluminum Cap GAZ-807000000 Anodized Aluminum Cap GAZ-811

InstallationE395 special socket avaiable.


Woodgrip™ FastenersWoodgrip, HiLo Woodgrip, Woodgrip XG,

Woodgrip #14 Type A MP, Low Profile WoodgripFor metal to wood

Metal to Wood

Woodgrip is the original sheet to wood fastener designed to self-drill metal panels:• High Hex Washer Head provides driving stability

and a sharp point for quick installation.• Assembled with a control seal washer for a consistent,

weather tight seal and improved installation appearance.• Extended corrosion resistant coating system.

Woodgrip XG is a sheet to wood fastener designed to self drill metal panels:• Superior performance in OSB, plywood and 1x4 pine.• Superior resistance to stripout• Extra aggresive thread design.• Improved pullout and backout values over other wood screws

by as much as 30%.• Extended corrosion resistant coating system.

Woodgrip # 14 Type A mill point carbon steel self-tapping fasteners are designed for attaching both metal to wood and metal to metal:• These fasteners do not require a pre-drilled hole when

attaching 26 and 24 gage metal to wood.• Corrosion resistant coating system.

HiLo Woodgrip is a sheet to wood fastener designed to self-drill metal panels:• High Hex Washer Head provides driving stability

and a milled point for quick installation.• Assembled with a bond seal washer for a consistent, weather

tight seal and improved installation appearance.• Extended corrosion resistant coating system.

Low Profile Woodgrip is a sheet to wood fastener designed to self-drill metal panels:• Low profile head for pleasing appearance. • Mill point ensures great drill performance.• HiLo thread with added pull-out resistance.• Available with bond seal for exterior sidewall application or no washer for interior applications.• Corrosion resistant coating system.

ApplicationWoodgrip 9–15 HWH Sharp PointAssembled with Control Seal Metal to woodDrilling capacity: 24 ga (.024)Self-drills through the metal panel and taps into wood substrate. Min penetration in wood substrates should be no less than 1"

HiLo Woodgrip 10 –15Assembled Bond Seal washer Metal to woodDrilling capacity: 24 ga (.024)Self-drills through the metal panel and taps into wood substrate. Min penetration in wood substrates should be no less than 1"

Woodgrip XG 12– 8 HWH Sharp Point Assembled with Control Seal Metal to woodDrilling capacity: 24 ga (.024) Self-drills through the metal panel and taps into wood substrate. Large, aggressive thread design provides superior resistance to strip-out, and superior performance in OSB, plywood, and 1x4" pine. Min penetration in wood substrates should be no less than 1"

1/4" Hex Washer Head Thread Major Dia: .181 – .175 Thread Minor Dia: .133 – .127Strength (lbs ult.): Tensile: 1500 Torsional: 60 in-lbs min. Shear: 933

File Name: WG6.1_C0261.epsCreated by: EWB-11/27/02





NotesDimensions are nominal inches unless noted.



ApplicationWoodgrip 12 x 3/4 LapAssembled Bond Seal washerDrilling capacity: 2 x 24 gaPanel to panel side lap, end lap and other stitch applications

Woodgrip™ Fasteners

Metal to Wood

1/4" Hex Washer Head: Thread Major Dia: .215 – .208 Thread Minor Dia: .164 – .157Strength (lbs ult.): Tensile: 2100 Torsional: 92 in-lbs min. Shear: 1800





Woodgrip HiLo 10-15 Low Profile Exterior Sidewall Fastener, Bond SealDrilling capacity: 24 ga. (.024) Self-drills through the metal panel and taps into wood substrate. Min penetration in wood substrates should be no less than 1"

Woodgrip HiLo 10-15 Low ProfileInterior Liner Panel, No WasherDrilling capacity: 24 ga. (.024)Self-drills through the metal panel and taps into wood substrate. Min penetration in wood substrates should be no less than 1"

Available painted white only.

#14 Type A Milled PointCarbon Steel, Silver Sentri Metal to woodSelf-drilling metal thickness: Sheet .018 – .030Thickness is based on normal, single or multiple material thickness combined for total.

Min depth penetration into the wood sub structure: 1"


T25 TORX Pan Head: Thread Major Dia: .199 - .191 Thread Minor Dia: .133 - .127Strength (lbs ult.): Tensile: 1500 Torsional: 60 in-lbs min. Shear: 933

T25 TORX Pan Head: Thread Major Dia: .199 - .191 Thread Minor Dia: .133 - .127Strength (lbs ult.): Tensile: 1500 Torsional: 60 in-lbs min. Shear: 933


5/16" AF Hex Washer HeadThread Major Dia: .254 – .248 Thread Minor Dia: .185 – .178Strength (lbs ult.): Tensile: 3500 Torsional: 125 in-lbs Shear: 2400





Woodgrip, HiLo Woodgrip, Woodgrip XG,Woodgrip #14 Type A MP, Low Profile Woodgrip

For metal to wood

Performance Pounds Ultimate Pull-out (lbs ult.) Wood: Spruce, Pine, Fir

#9 Woodgrip Control Seal Washer1-1/2" Penetration 7481" Penetration 542

#10 HiLo Woodgrip Bond Seal Washer1-1/2" Penetration 8201" Penetration 524

#10 HiLo Torx Pan Head Woodgrip1-1/2" Penetration 8201" Penetration 524

#14 Type A Milled Point1" Penetration 1013

% Increase Strip-out Pull-out (lbs ult.) vs. Woodgrip (in-lbs)

#12 Woodgrip XG Control Seal WasherSPF 1-1/2" Penetration 874 20SPF 1" Penetration 571 201x4" Pine 590 343/4" Plywood 587 255/8" Plywood 446 311/2" Plywood 384 3923/32" OSB 524 2119/32" OSB 456 31

Notes: Woodgrip and HiLo pull-out strength values may vary from tested loads depending upon specific wood density variations. Woodgrip and HiLo pull-over strength values are based on .035" thick, ½" OD Control Seal or Bond Seal washer and have been updated to reflect common tensile strengths of metal panels as a function of panel thicknesses.

TORX® pan head HiLo pull-out strength values may vary from tabulated loads depending upon specific wood density variations. Pull over strength values are based on ½" nominal OD TORX® head and AZ55 Galvalume steel material.

Percent increase strip-out values of the Woodgrip XG over the standard Woodgrip are typical results, as encountered when fasteners are installed at 2500 rpm until full strip-out occurs.

Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fastener.

Metal to Wood

Fasteners installed in less than 1" of solid wood may have an increased potential for sealing or connection failure over time. This may be due to the fasteners being stripped out during installation and/or due to the lack of adequate wood fiber material to hold the fastener in place during thermal movement cycles or other forces which may be exerted upon the connection.

Pull-over

29 ga (110 ksi): 57726 ga (70 ksi): 63724 ga (70 ksi): 800

SelectionSize Woodgrip HiLo Woodgrip Woodgrip XG Exterior Low Profile Interior Liner Panel #14 A Milled Point1" V0161-CCF V1008-CDF V1806-EMF A0408-CFF A0308-001F V3321-GBF1-1/2" V0261-CCF V1012-CDF V1841-EMF A0412-CFF — V3438-GBF2" V0381-CCF V1016-CDF V1851-EMF A0416-CFF — V3531-GBF2-1/2" V0461-CCF V1020-CDF V1856-EMF — — A3597-GBF3" V0485-CCF V1024-CDF V1861-EMF — — A3626-GBF12 x 3/4" (1/4" HWH) V1701-ECF V1707-EAF — — —

InstallationTools: 0 – 2500 rpm screw driver equipped with depth sensing nose piece.

ZAC®



5 6 7 3 2 1 ?4



MAC™



5 6 7 3 2 1 ?4



Painted



5 6 7 3 2 1 ?4



OptionsVistaCoat™

Woodgrip™ Fasteners

Pull-over


29 ga (110 ksi): 57726 ga (70 ksi): 637


22 ga (.030): 109724 ga (.024): 81026 ga (.018): 564

Woodgrip, HiLo Woodgrip, Woodgrip XG,Woodgrip #14 Type A MP, Low Profile Woodgrip

For metal to wood

EVERGRIP® 300 Series Stainless Fasteners

EVERGRIP stainless bi-metalFor metal to wood

Metal to Wood

EVERGRIP stainless wood fastener is designed to self-drill metal panels:• Head and the majority of shank is 300 Series Stainless Steel, with a

welded, hardened carbon steel point for self-drilling performance.• Provides the corrosion protection of stainless with the drill

performance of a carbon steel fastener.

• Designed specifically for superior corrosion resistance in all wood treatments.

• Available with HWH or TORX drive pan head.

ApplicationEVERGRIP 9 – 15 HWH Sharp PointAssembled with stainless Bond SealMetal to woodDrilling capacity: 24 ga (0.024)Self-drills through the metal panel and taps into wood substrate. Min penetration in wood substrates should be no less than 1"

EVERGRIP 9 – 15 T-25 (TORX®) Pan HeadAssembled with stainless Bond SealMetal to woodDrilling capacity: 24 ga. (0.024)Self-drills through the metal panel and taps into wood substrate. Min penetration in wood substrates should be no less than 1"


EVERGRIP Stainless Bond Seal1-1/2" Penetration 7481" Penetration 542

Notes: Dimensions are nominal inches unless noted. Pull out strength values may vary from tabulated loads depending upon specific wood density variations. Pull over strength values are based on AZ55 Galvalume steel material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied.

Selection HWH HWH T-25 Pan HeadLength 250/Bag 100/Box 250/Bag1" E4160-CUF E4160-CUEG 11199341-1/2" E4260-CUF E4260-CUEG 11241802" E4380-CUF E4380-CUEG 11199372-1/2" E4460-CUF E4460-CUEG 11270143" — — 1119938

Description Part No. QuantitySFS Special T-25 Torx drive bit 0514261 1 each





InstallationTools: 0 – 2500 rpm screwdriver equipped with depth sensing nosepiece. The EVERGRIP 9-15 T-25 (TORX) Pan Head requires a T-25 Torx drive bit.Utilizing the special SFS T-25 Torx drive bit manufactured by SFS intec is recommended for superior stability during the installation process.

OptionsPainted



5 6 7 3 2 1 ?4



1/4" Hex Washer Head Thread Major Dia: 0.181 – 0.175 Thread Minor Dia: 0.133 – 0.127Strength (lbs ult.): Tensile: 1657 Torsional: 50 in-lbs min. Shear: 1550

Pull-over

29 ga: 37826 ga: 51924 ga: 704


NEGATIVE reduced 00%File Name: P_1481A_E.eps

Created by:EWB-04/8/08Revised: MPD-00/00/08

T-25 (TORX) Pan Head Head Dia: 0.393–0.374” Thread Major Dia: 0.181 – 0.175 Thread Minor Dia: 0.133 – 0.127Strength (lbs ult.): Tensile: 1657 Torsional: 50 in-lbs min. Shear: 1550Utilizing the special SFS T-25 Torx drive bit manufactured by SFS intec is recommended for superior stability during the installation process.


300 Series Stainless Aluminum Panel Woodgrip™

Woodgrip stainlessFor aluminum panel

Metal to Wood

Stainless, Aluminum Panel Woodgrip is an all stainless wood fastener designed for use with aluminum panels:• Fastener is 304 stainless steel for corrosion protection.• High hex washer head provides driving stability

and a sharp point for quick installation into aluminum. • Will not drill steel panels.

ApplicationStainless Aluminum Panel Woodgrip 9 – 15 HWH Sharp PointAssembled with aluminum Bond SealMetal to woodSelf-drills through aluminum panel and taps into wood substrate. Min penetration in wood substrate should be no less than 1"


#9 Woodgrip Stainless Aluminum Bond Seal1-1/2" Penetration 7481" Penetration 542

Notes: Dimensions are nominal inches unless noted. Pull out strength values may vary from tabulated loads depending upon specific wood density variations. The specific job conditions should be considered and appropriate safety factors applied. Stainless Woodgrips are not designed to self-drill steel panels.


SelectionSize Stainless Woodgrip1" E0225-CKF1-1/2" E0270-CKF2" E0272-CKF2-1/2" E0275-CKF3" E0277-CKF






OptionsPainted



5 6 7 3 2 1 ?4



1/4" Hex Washer head Thread Major Dia: .181 – .175 Thread Minor Dia: .133 – .127Strength (lbs ult.): Tensile: 1657 Torsional: 50 in-lbs min Shear: 1550

Woodgrip™ Capped Fasteners WoodZAC® and WoodMAC™For metal to wood

Metal to Wood

WoodZAC has all the performance features of standard Woodgrip fasteners, plus a zinc alloy cap that can never red rust:• 5/16" AF high Hex Washer Head for driving stability

and a sharp point for quick installation. • Assembled with a aluminum bond seal for weather tight

seal and improved installation appearance.

WoodMAC has all the performance features of standard Woodgrips:• 1/4" AF 300 series stainless capped HWH for a low profile head

appearance that can never rust.

ApplicationHiLo WoodZAC 10–15 HWH Mill PointAssembled with aluminum Bond Seal Metal to woodDrilling capacity: 24 ga (.024)Self-drills through the metal panel and taps into wood substrate. Min penetration in wood substrates should be no less than 1"

WoodZAC XG 12–8 HWH Sharp PointAssembled with EPDM washerMetal to WoodDrilling capacity: 24 ga (.024)Self-drills through the metal panel and taps into wood substrate. Min penetration in wood substrates should be no less than 1"

WoodZAC 12 x 3/4" LAP Sharp PointAssembled with EPDM washerPanel to panel side lap, end lap and other stitch applications

#14 ZAC Type A Milled PointMetal to woodSelf-drilling metal thickness: Sheet .018 – .030Thickness is based on normal, single or multiple material thickness combined for total.Min depth penetration into the wood sub structure: 1"






5/16" Hex Washer Head Zinc Alloy Cap Thread Major Dia: .199 - .191 Thread Minor Dia: .133 – .127Strength (lbs ult.): Tensile: 1500 Torsional: 60 in-lbs min. Shear: 933

5/16" Hex Washer Head Zinc Alloy Cap Thread Major Dia: .215 – .209 Thread Minor Dia: .133 – .127Strength (lbs ult.): Tensile: 2183 Torsional: 60 in-lbs min. Shear: 1946


5/16" Hex Washer Head Zinc Alloy Cap Thread Major Dia: .215 – .208 Thread Minor Dia: .164 – .157Strength (lbs ult.): Tensile: 2100 Torsional: 92 in-lbs min. Shear: 1800

3/8" AF Zinc Alloy Capped Thread Major Dia: .254 – .248 Thread Minor Dia: .185 – .178Strength (lbs ult.): Tensile: 3500 Torsional: 125 in-lbs Shear: 2400





Metal to Wood


Application1/4 ZAC Type AB Milled PointMetal to metal Metal to woodSelf-drilling metal thickness: Sheet .018 – .030Thickness is based on normal, single or multiple material thickness combined for total. Min depth penetration into the wood sub structure: 1"

WoodMAC 9–15 HWH Sharp PointAssembled with EPDM washer Metal to woodDrilling capacity: 24 ga (.024) Self-drills through the metal panel and taps into wood substrate. Min penetration in wood substrates should be no less than 1"

WoodMAC Lap 12 x 3/4" HWH Sharp Point Assembled EPDM washerPanel to panel side lap, end lap and other stitch applications





1/4" Cupped Stainless Capped Thread Major Dia: .215 – .208 Thread Minor Dia: .164 – .157Strength (lbs ult.): Tensile: 2100 Torsional: 92 in-lbs min. Shear: 1800


#10 HiLo Woodgrip 5/16" ZAC Aluminum Bond Seal1-1/2" Penetration 8201" Penetration 524

#9 Woodgrip 1/4" MAC EPDM Washer1-1/2" Penetration 7481" Penetration 542

#14 A Milled Point 3/8" ZAC1" Penetration 1013

1/4" AB Milled Point 3/8" ZAC1" Penetration 1013

Pull-over

29 ga: 57726 ga: 63724 ga: 800

29 ga: 38026 ga: 50024 ga: 710

File Name: WG6.2_C0268.epsCreated by: MPD-12/02/02




1/4" Cupped Stainless Capped Thread Major Dia: .181 – .175 Thread Minor Dia: .133 – .127Strength (lbs ult.): Tensile: 1500 Torsional: 60 in-lbs min. Shear: 933

3/8" AF Zinc Alloy Capped Thread Major Dia: .246 – .240 Thread Minor Dia: .192 – .185Strength (lbs ult.): Tensile: 3800 Torsional: 142 in-lbs Shear: 2500





26 ga: 56424 ga: 81022 ga: 1097

26 ga: 60024 ga: 86622 ga: 1094

Notes: Dimensions are nominal inches unless noted.

Metal to Wood


SelectionSize HiLo WoodZAC WoodZAC XG WoodZAC WoodMAC WoodMAC #14 A Milled Point #14 AB Milled Point Lap Lap 3/8" ZAC 3/8" ZAC1" A1066-DNF A1807-FCF — C0168-CAF — A3325-FMF A4395-FMF1-1/4" — — — — — — A4428-FMF1-1/2" A1071-DNF A1842-FCF — C0268-CAF — — A4485-FMF2" A1076-DNF A1852-FCF — C0388-CAF — — A4513-FMF2-1/2" A1081-DNF A1857-FCF — C0468-CAF — — A4510-FMF3" A1086-DNF A1862-FCF — C0488-CAF — — —12 x 3/4" ZAC (5/16" HWH) — — A1705-FLF — — — —12 x 3/4" MAC (1/4" HWH) — — — — A1708-EYF — —

InstallationTools: Tools: Metal to metal application: 0 – 600 rpm screwdriver equipped with depth sensing nosepiece. Metal to wood application: 0 – 2500 rpm screwdriver equipped with depth sensing nosepiece.

Painted



5 6 7 3 2 1 ?4



OptionsVistaCoat™

Pull-out (lbs ult.) Strip Out* (in lbs) Pull-over

#12 WoodZAC XG EPDM WasherSPF 1-1/2" Penetration 874 79 29 ga (110 ksi): 577SPF 1" Penetration 571 68 26 ga (70 ksi): 637 1 x 4" Pine 590 51 24 ga (70 ksi): 8003/4" Plywood 587 65 5/8" Plywood 446 421/2" Plywood 384 5323/32" OSB 524 7619/32" OSB 456 64

* Strip-out values were determined by the dynamic strip-out test, wherein fasteners were driven though a 24 gage panel into the applicable substrate at 2500 rpm until stripout occured. The strip-out values listed above represent the average maximum strip-out measured by the digital data acquisition system when the fastener was driven into the given substrate.

Notes: Woodgrip and WoodZAC pull out strength values may vary from tabulated loads depending upon specific wood density variations. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners.


(RH2) Product Name: #14 (RH3) Description: #3 Phillips Drive(RH4) Application: Insulation board to roof cover.Panelmaster® Collated belted fasteners

For Post Frame Metal Panel Attachment

Panelmaster® Fastening System

• Increased speed of installation• Improved working ergonomics• Stand-up roof attachment

• Fasteners installed uniformly every time• Special footpieces available for attachment through the panel rib• Installs fasteners 1"– 3" long

ApplicationPanelmaster™ Tool KitStandard tool kit includes: – Panelmaster tool– DeWalt® 18V drive unit – Battery charger and extra battery– One extension piece– Extra drive bits – Corded DeWalt drive unit available– One-year full replacement warranty

Belted Fasteners – SFS intec fasteners 1" through 3" lengths

with sealing washers– Can be painted to match any panel color – All fasteners packaged 500 per carton

Woodgrip™ FastenersItem Length SFS Part #

Woodgrip 9 –15 HWH Control Seal Washer VistaCoat

1" V0161-CCBL

1-1/2" V0261-CCBL

2" V0381-CCBL

2-1/2" V0461-CCBL

3" V0485-CCBL

HiLo Woodgrip 10 –15 HWH Bond Seal Washer VistaCoat

1" V1008-CDBL

1-1/2" V1012-CDBL

2" V1016-CDBL

2-1/2" V1020-CDBL

3" V1024-CDBL

Woodgrip XG 12 –11 HWH Bond Seal Washer VistaCoat

1" V1806-EMBL

1-1/2" V1841-EMBL

2" V1851-EMBL

2-1/2" V1856-EMBL

3" V1861-EMBL

Long-Life FastenersItem Length SFS Part #

WoodMAC 9-15 HWH Seal WasherVistaCoat

1" C0168-CABL

1-1/2" C0268-CABL

2" C0388-CABL

2-1/2" C0468-CABL

3" C0488-CABL

Evergrip 9-15 HWH Stainless Bond Seal Washer

1" E4160-CUBL

1-1/2" E4260-CUBL

2" E4380-CUBL

2-1/2" E4460-CUBL

Evergrip 9-15 Torx Stainless Bond Seal Washer

1" 1110324

2" 1110327

3" 1110329

Selection

1-3/4" Snap Lock (3 hole) ClipG90 Galvanized: 20 ga. Packaged 500 per carton

Standing Seam Clips Engineered panel clipsFor standing seam panel attachments

Panel Clips, Bearing Plates and Fasteners

• Engineered panel clips are custom designed and manufactured for your panel system.

• Clips are supplied in galvanized steel, coated steel, stainless steel and other materials.

• Engineered fixed and float clip designs are available.

• Standard clips are available from stock without tooling cost to you.• Sealant can be pre-applied to the clips to maintain the seal

at the clip attachment.• Clip design options are available for review and evaluation.• All clips also available in stainless steel.

Application - Snap LockSnap Lock Panel DesignConfigurations require very low profile clip bases with a base feature to hold the panel above the low profile fastener heads.

Selection1" Snap Lock ClipG90 Galvanized: 18 ga. Packaged 200 per carton

1-1/2" Snap Lock G90 Galvanized: 18 ga. or 20 ga. Packaged 500 per carton

1-5/8" Snap Lock (3 hole) Clip G90 Galvanized: 18 ga. Packaged 500 per carton


Fixed Clips are primarily used with these panels. Low profile head fasteners should be used with these panels to provide clearance for the panel over the fastener heads. These clips are manufactured from steel, stainless steel and other materials with various finishes to fit the needs of the panel application.

Roof Panel

RoofPanel

Clip

BlanketInsulation

Roof Purlin

Low ProfileHead Fastener

1-1/2" Snap Lock ClipG90 Galvalume: 24 ga. Packaged 1000 per carton

1-1/2" Snap Lock ClipG90 Galvanized: 18 ga. Packaged 125 per carton


Roof Panel

RoofPanel

Clip

BlanketInsulation

Roof Purlin




Application - Snap LockBattenTrim (spider) Clip304SS (1/4 Hard): 22 ga.Packaged 500 per carton

Application - Architectural/MechanicalArchitectural/Mechanical Panel DesignConfigurations require low profile bases with clearance for the fastener head.

Selection1-1/2" Fixed Clip (.38 Hor.)G90 Galvanized: 22 ga. Packaged 250 per carton

2" Fixed Clip (.57 Hor.)G90 Galvanized: 22 ga. Packaged 250 per carton


2-3/8" Fixed Clip (.70 Hor.)G90 Galvanized: 22 ga.Factory applied sealant Packaged 250 per carton

1-1/2" Fixed Clip (.43 Hor.)G90 Galvanized: 24 ga. Packaged 350 per carton

2" Fixed Clip (.70 Hor.)G90 Galvanized: 22 ga.Factory applied sealant Packaged 400 per carton

Fixed and Float Clips are used with these panels. The clips may have pre-applied sealant to maintain the panel seal at the clip attachment point. These clips are manufactured from steel, stainless steel and other materials with various finishes to fit the needs of the panel application.

RoofPanel

Sliding ClipAssembly

BlanketInsulation

Roof Purlin

RoofPanel

RoofPanel

Sliding ClipAssembly

BlanketInsulation

Roof Purlin

RoofPanel





Application - Architectural/Mechanical3" Fixed Clip (.66 Hor.)G90 Galvanized: 22 ga. Packaged 200 per carton

3" Fixed Clip (.935 Hor.)G90 Galvanized: 22 ga. and 24 ga. Packaged 250 per carton

1-1/2" Float Clip (.65 Hor.)G90 Galvanized: 22 ga. TabBase: 16 ga. Factory applied sealant Packaged 100 per carton

1-1/2" Float Clip (.71 Hor.)G90 Galvanized: 22 ga. Tab Base: 16 ga. Packaged 100 per carton

2" Float Clip (.70 Hor.)G90 Galvanized: 22 ga. Tab Base: 16 ga.Factory applied sealant Packaged 100 per carton

2" Float Clip (.70 Hor.)G90 Galvanized: 22 ga. Tab Base: 16 ga. Factory applied sealant Packaged 100 per carton



3" Fixed Clip (.70 Hor.)G90 Galvanized: 22 ga.Factory applied sealant Packaged 250 per carton

1-1/2" Float Clip (.38 Hor.)G90 Galvanized: 22 ga. Tab Base: 16 ga. Packaged 80 per carton

2" Float Clip (.57 Hor.)G90 Galvanized: 22 ga. Tab Base: 16 ga. Packaged 80 per carton




(RH3) Description: #3 Phillips Drive(RH4) Application: Insulation board to roof cover.Standing Seam Clips Engineered panel clips

For standing seam panel attachments

Application - Architectural/Mechanical2" Float Clip (.71 Hor.)G90 Galvanized: 22 ga. Tab Base: 16 ga. Packaged 60 per carton


3-3/8" Float Clip (.71 Hor.) For 2" PanelG90 Galvanized: 22 ga. Tab Base: 16 ga. Packaged 70 per carton

3-3/8" Float Clip (.71 Hor.)For 3" Panel G90 Galvanized: 22 ga. Tab Base: 16 ga. Packaged 80 per carton




4-3/8" Float Clip (.71 Hor.) For 3" PanelG90 Galvanized: 22 ga. Tab Base: 16 ga. Packaged 60 per carton


Application - Architectural/MechanicalButterfly Tab 1-1/2"G90 Galvanized: 22 ga. Packaged 200 per carton

Butterfly Tab 2"G90 Galvanized: 22 ga.Packaged 150 per carton


Continuous Base 1-1/2" or 2"1-1/2"–G90 Galv.: 22 ga. 1-1/2" Packaged 125 10ftpieces per carton2"–G90 Galv.: 18 ga. 2" Packaged 100 10ftpieces per carton


Butterfly Base 1-1/2"G90 Galvanized: 22 ga. Packaged 200 per carton

Butterfly Base 2"G90 Galvanized: 18 ga. Packaged 150 per carton

Application - Bearing Plates

Snap Lock Bearing PlateDimension 4.75" x 6" 24 ga. G-90 Galv. Packaged 125 per carton

• Unique design fits most standing seam clips• Hole spacings can be customized to meet

customer requirements

• Produced in 16-26 ga. materials• Available in various dimensions

Universal Bearing PlateDimension: 4" x 6"or 4" x 5"18, 20, 22 and 24 ga. G-90 Galv. Packaged 125 per carton

Snap Lock and Universal Bearing Plates Bearing PlatesFor standing seam panel attachments


Clip Fasteners Clip attachment fastenersFor metal to metal, metal to wood

• Designed with unique head styles, drill point configurations and material types to meet performance requirements to attach standing seam roof clips.

• Engineered profile features preventing panel damage from fastener head contact.

• Engineered installation torque drive control for uniform installation performance.

Application#10 Type A: Pancake Head 2/2 Quadrex DriveCarbon Steel, Zinc Plated Metal to wood

#10 Type A: Pancake Head Phillips Drive300 Series Stainless SteelMetal to wood

#10 Self-Drill: Pancake Head 2/2 Quadrex DriveCarbon Steel, Zinc PlatedMetal to metalMin projection: 3/8" of threads below substrate

#12–8 XG Sharp Point: Pancake Head 2/2 Quadrex DriveCarbon Steel , Zinc PlatedMetal to wood

#12 Type A: Pancake Head 2/2 Quadrex DriveCarbon Steel , Zinc PlatedMetal to wood

#12 Self-Drill: Pancake Head 2/2 Quadrex DriveCarbon Steel , Zinc PlatedMetal to metalMin projection: 3/8" of threads below substrate .

Head Height: .080 – .068 Head Dia: .447 – .423 Thread Major Dia: .194 – .188 Thread Minor Dia: .133 – .126Strength (lbs ult.): Carbon Stainless Tensile: 1825 1653 Torsional: 48 in-lbs 50 in-lbs Shear: 1535 1587#10 Type A, Pull-out (lbs ult.):SPF wood: 1" penetration: 821#10 Self Drill, Pull-out (lbs ult.): 12 ga (.105): 1782 14 ga (.075): 1072 16 ga (.060): 782

Roof Panel

RoofPanel

Clip

BlanketInsulation

Roof Purlin










Head Height: .080 – .068 Head Dia: .447 – .423 Thread Major Dia: .221 – .215 Thread Minor Dia: .162 – .155Strength (lbs ult.): Tensile: 1940 Torsional: 90 in-lbs Shear: 1805Pull-out (lbs ult.): SPF wood: 1" penetration: 724









Head Height: .080 – .068 Head Dia: .447 – .423 Thread Major Dia: .215 –.209 Thread Minor Dia: .133–.127Strength (lbs ult.): Tensile: 2183 Torsional: 60 in-lbs Shear: 1946Performance (lbs ult.): Pull-out SPF 1-1/2" Penetration 874SPF 1" Penetration 5711x4" Pine 5903/4" Plywood 5875/8" Plywood 4461/2" Plywood 38423/32" OSB 52419/32" OSB 456

Head Height: .090 – .078 Head Dia: .447 – .423 Thread Major Dia: .215 – .209 Thread Minor Dia: .164 – .157Strength (lbs ult.): Tensile: 2900 Torsional: 92 in-lbs Shear: 2050Pull-out (lbs ult.): 12 ga (.105): 1539 14 ga (.075): 1010 16 ga (.060): 724



Panel Clips and Fasteners

Clip Fasteners Clip attachment fastenersFor metal to metal, metal to wood

Application1/4 -14 #2 Point Drilling capacity (#2 point): .050 – .150Attachment thickness: Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total. Min projection: 3/8" of threads below substrate

12-24 #5 Point: Pancake Head 2/2 Quadrex DriveCarbon Steel, Zinc PlatedMetal to metalDrilling capacity: .075 – .500Attachment thickness: Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total.Min projection: 3/8” of threads below substrate

NotesDimensions are nominal inches unless noted. Pull-out values (pounds ultimate) are based on 50,000 psi hot rolled steel sheet material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners.Fasteners installed in less than 1" of solid wood may have an increased potential for a connection failure over time. This may be due to the fasteners being stripped out during installation and/or due to the lack of adequate wood fiber material to hold the fastener in place when forces are exerted upon the connection.

Selection

5/16" AF Hex Washer Head 3/8" AF Hex Washer Head Thread Major Dia: .246 – .240 Thread Minor Dia: .192 – .185Strength (lbs ult.): Tensile: 3800 Torsional: 150 in-lbs Shear: 2850#2 Point, Pull-out (lbs ult.): 12 ga (.105): 2088 14 ga (.075): 1312 16 ga (.060): 903

BlanketInsulation

RoofPanel

Roof Purlin

RoofPanelClip

RoofPanel

File Name: WG(7.2)_S5271_14_14Impax.epsCreated by: EWB-12/12/02




Head Height: .090 – .078 Head Dia: .447 – .423 Thread Major Dia: .216 – .210 Thread Minor Dia: .186 – .181Strength (lbs ult.): Tensile: 3450 Torsional: 100 in-lbs Shear: 2420Pull-out (lbs ult.): 12 ga (.105): 1378 3/16" (.187): Exceeds tensile value 1/4" (.250): Exceeds tensile value

InstallationTools: 2000 – 2500 rpm #10 self drill, 0 – 2000 rpm on 1/4-14 self drill screwdriver equipped with depth sensing nosepiece.

Length

#10 Type A Pancake

Carbon Steel

#10 Type A Pancake

Stainless Steel#10 Self-Drill

Pancake#12–8 XG Pancake

#12 Type A Pancake

#12 Self-Drill Pancake

12–24 #5 Point Pancake

1/4–14 #2 Point 5/16 AF HWH

1/4–14 #2 Point3/8 AF HWH

1" A1191F E0235F S3431F A1900F A1710F S4552F — — S5171F1-1/4" — — — — — — — S5191F —1-1/2" A1351F — S4221F A1940F — — S4750F S5286F S5271F2" A1391F E0271F S4421F A1950F — — — — —

AceClamp® Attachment Solution forStanding Seam Roofs


• Fast - No assembly required• Easy - One top-mount fastener• Secure - Locks in place

Attachment Solution for: • solar • HVAC • snowrails • conduit • windclamps • signs

ApplicationAceClamp® MLFits Mechanical Lock panels

AceClamp® SLFits - Snaplock panels

- Mechanical Lock panels with seam dimension of ≤ .500"

Single Lock Double Lock T-Seam Z-Rib

3.00”

1.437”

0.812”

0.50”

0.625”

2.06”

0.90”

Mechanical Lock(small seam)

Snaplock

0.58”1.91”

2.60”0.97”

0.50”

NotesAceClamp® is not designed for use on batten seam panel systems and is not recommended for nail flange panel systems.AceClamp® is not to be used as any part of a fall protection system.For all applications, determining the suitability of the product and the installation orientation relative to the seam are the responsibility of the professional design engineer.

SelectionModel Part # PackagingAceClamp® ML 1287430 20 per box/5 boxes per caseAceClamp® SL 1287441 20 per box/5 boxes per caseDrive Bit 1287429 -

InstallationTools: 1/4" hex driver (bit #1287429). Finish tightening with calibrated torque wrench.

SOL-R Solar Fastening Systemfor exposed fastener metal roofs


Fast, Easy, Secure• Installs quickly• Rapid adjustment• UV resistant, corrosion-free• Eliminates conductivity

SpecificationsSOL-R

Material

• System components of metal substitute Polyphthalamide (PPA) with 50% glass

fiber reinforcement• A2/AISI 304 stainless steel bolt for height and position adjustment• Aluminum reinforcement plates on the base plate• Pre-assembled butyl sealant on the base plate

NotesAll calculations, measurements, fasteners and design methods have to be verified by a responsible designer or an engineer,regarding the corresponding structure and loads. Please consult local, regional and national codes and approval requirements.

SelectionDescription Part # PackagingSOL-R 1246887 50 units/case

Docking device

Cap

Base plate

4.41"

.3"

1.18

"

1.65

"

min

. hei

ght

2.5"

max

. hei

ght

4.5"

4.8"

fle

xibl

ehe

ight

adj

ustm

ent

2"

.53"1.6"

.7"

Dimensions

Values based on central fasteningsTest result is valid for the whole range of the setting position.

x = arithmetical mean value s = standard deviation

x = 846 lb 3765Ns = 73 lb 327N

F

Compression strength DbTest results refer to the ultimate load required for the component to break when stressed in compression. The force F is applied on the contact surfaces of the component.

x = 505 lb 2248Ns = 15 lb 68N

F

Tensile strength ZbTest results refer to the ultimate load required for the component to break when stressed in tension. The force F is applied on the contact surfaces of the component.

x = 387 lb 1724Ns = 23 lb 104N

F

Shear strength QbTest results refer to the ultimate load required for the component to break when stressed in shear. The force F is applied on the contact surfaces of the component.

If the SOL-R docking device is placed in a vertical position, calculate with the following values:

Db x = 364 lb 1621N s = 29 lb 130N Zb x = 346 lb 1543N s = 20 lb 89N

Qb x = 346 lb 1543N s = 20 lb 89N

(RH2) Product Name: #14 (RH3) Description: #3 Phillips Drive(RH4) Application: Insulation board to roof cover.Blind Rivets Blind rivets attach light gage


Selection BULB-TITE® Rivets BULB-TITE rivets were first developed to solve application requirements in the Pre-Engineered Metal Building industry. Since that time the BULB-TITE product line has been expanded to meet application requirements in a wide range of industries. The BULB-TITE rivet body folds into three seperate legs forming a large blind-side head. This large bearing head evenly distributes the BULB-TITE's clamp force in soft, thin or brittle materials while providing high pull-through resistance. The BULB-TITE's wide grip range enables a single BULB-TITE to work in a greater variation of thicknesses. Aluminum Rivet/Aluminum Mandrel

Part No. Part No. Head Style Rivet Diameter No Washer w/ Washer Grip Range Pre-Drill Hole SizeDome Head Protruding Crown 5/32" 1194602 1194603 .067-.250 #20 (.162-.167)Dome Head Protruding Crown 5/32" 1194604 1194605 .250-.500 #20 (.162-.167)Dome Head Protruding Crown 3/16" 1194606 1194607 .050-.187 #4 (.209-.221)Dome Head Protruding Crown 3/16" 1194608 1194609 .062-.250 #4 (.209-.221)Dome Head Protruding Crown 3/16" 1194620 1194621 .187-.375 #4 (.209-.221)Dome Head Protruding Crown 3/16" 1194622 1194623 .312-.500 #4 (.209-.221)Dome Head Protruding Crown 3/16" 1194624 1194625 .437-.625 #4 (.209-.221)Dome Head Protruding Crown 3/16" 1194626 1194627 .563-.750 #4 (.209-.221)Dome Head Protruding Crown 3/16" 1242652 1242653 .687-.875 #4 (.209-.221)Dome Head Protruding Crown 3/16" 1242654 1242655 .812-1.000 #4 (.209-.221)Dome Head Protruding Crown 3/16" 1242656 1242657 .937-1.125 #4 (.209-.221)Dome Head Protruding Crown 1/4" 1194628 1194629 .062-.250 1/4 (.250-.263)Dome Head Protruding Crown 1/4" 1194630 1194631 .125-.375 1/4 (.250-.263)Dome Head Protruding Crown 1/4" 1194632 1194633 .250-.500 1/4 (.250-.263)Dome Head Protruding Crown 1/4" 1194634 1194635 .375-.625 1/4 (.250-.263)Dome Head Protruding Crown 9/32" 1194718 1194719 .032-.375 5/16 (.304-.3125)Dome Head Protruding Crown 9/32" 1194720 1194721 .250-.625 5/16 (.304-.3125)Dome Head Protruding Crown 9/32" 1194722 1194723 .375-.750 5/16 (.304-.3125)Large Flange Prot. Crown 9/32" 1194724 1194725 .042-.375 5/16 (.308-.327)Large Flange Prot. Crown 9/32" 1194726 1194727 .250-.625 5/16 (.308-.327)Large Flange Prot. Crown 9/32" 1194728 1194730 .375-.750 5/16 (.308-.327)Dome Head Recessed Crown 3/16" 1242668 1242669 .050-.187 #4 (.209-.221)Dome Head Recessed Crown 3/16" 1242670 1242680 .062-.250 #4 (.209-.221)Dome Head Recessed Crown 3/16" 1242692 1242693 .187-.375 #4 (.209-.221)Dome Head Recessed Crown 3/16" 1242694 1242695 .312-.500 #4 (.209-.221)Dome Head Recessed Crown 3/16" 1242697 1242698 .437-.625 #4 (.209-.221)Dome Head Recessed Crown 3/16" 1242733 1242735 .563-.750 #4 (.209-.221)Dome Head Recessed Crown 3/16" 1242767 1242768 .687-.875 #4 (.209-.221)Dome Head Recessed Crown 3/16" 1242770 1242771 .812-1.000 #4 (.209-.221)Dome Head Recessed Crown 3/16" 1242773 1242774 .937-1.125 #4 (.209-.221)Dome Head Recessed Crown 1/4" 1242781 1242792 .040-.250 1/4 (.250-.263)Dome Head Recessed Crown 1/4" 1242795 1242796 .125-.375 1/4 (.250-.263)Dome Head Recessed Crown 1/4" 1242839 1242841 .250-.500 1/4 (.250-.263)Dome Head Recessed Crown 1/4" 1242868 1242870 .375-.625 1/4 (.250-.263)

• Many corrosion resistant options• Tamper resistant• Won't loosen in high vibration or fatigue applications• Quality and repeartability of assembly• No over-driving or under-driving• The installed function of the rivet will be consistent and is independent of the installer's technique• Easy to use, lightweight portable installation tools


Blind Rivets Blind rivets attach light gage


Selection MEGA GRIP® Rivets The MEGA GRIP is a high strength structural blind rivet offering several advantages over conventional blind rivets. MEGA GRIP's wide grip range enables a single MEGA GRIP to replace up to five different lengths of standard rivets. High shear strength is achieved by MEGA GRIP's flush break self plugging mandrel. MEGA GRIP rivets are hole-filling, resulting in tighter joints and improved sealing for weather resistance. MEGA GRIP rivets are installed via standard rivet tools and do not require special nose tips. Aluminum Rivet/Aluminum Mandrel

Head Style Rivet Diameter Part No. Grip Range Pre-Drill Hole SizeDome 3/16" 1194560 .062-.250 #8 (.194-.204)Dome 3/16" 1194561 .062-.437 #8 (.194-.204)Dome 1/4" 1194562 .080-.375 G (.259-.272)Dome 1/4" 1194567 .080-.625 G (.259-.272)Countersunk 3/16" 1242624 .125-.312 #8 (.194-.204)Countersunk 3/16" 1216216 .275-.500 #8 (.194-.204)Countersunk 1/4" 1242625 .125-.437 G (.259-.272)Countersunk 1/4" 1242626 .125-.625 G (.259-.272)Large Flange 3/16" 1242631 .062-.250 #8 (.194-.204)Large Flange 3/16" 1242642 .062-.437 #8 (.194-.204)Large Flange 1/4" 1242628 .080-.375 G (.259-.272)Large Flange 1/4" 1242630 .080-.625 G (.259-.272)


Extra Length Metric Rivets SFS intec supplies a complete line of metric blind rivets according to DIN7337 standards in 3mm, 4mm and 5mm diameters. Standard material is Aluminum/Steel. Stainless Steel 304 and 316 alloys are available upon special request. All dimensions for Metric Series are given in millimeters. Additional diameters of 4.8mm, 6mm and 6.4mm available on special request.

Aluminum Rivet/Steel MandrelHead Style Rivet Diameter Part No. Grip Range Pre-Drill Hole SizeDome 3mm 1194509 13-15 3.1Dome 3mm 1194531 15-17 3.1Dome 3mm 1194532 17-22 3.1Dome 3mm 1194534 22-25 3.1Dome 4mm 1194535 12.5-14.5 4.1Dome 4mm 1194536 14.5-16.5 4.1Dome 4mm 1194537 16.5-21.5 4.1Dome 4mm 1194538 21.5-26 4.1Dome 4mm 1194539 26-30 4.1Dome 4mm 1194540 30-35 4.1Dome 5mm 1194541 25-30 5.1Dome 5mm 1194542 30-35 5.1Dome 5mm 1194543 35-40 5.1Dome 5mm 1194544 40-45 5.1Dome 5mm 1194545 45-48 5.1Dome 5mm 1194546 48-52 5.1Dome 5mm 1194547 52-57 5.1Dome 5mm 1194549 57-62 5.1Dome 5mm 1194550 62-72 5.1



Selection PolyGrip® Multigrip Blind Rivets PolyGrip rivets feature a wide grip range, enabling a single PolyGrip to replace up to three different lengths of standard blind rivets. PolyGrip rivets expand radially, filling the application hole, resulting in tighter joints and improved sealing. The PolyGrip's locked mandrel core creates a weather resistant fastener. Improved material support is provided by the PolyGrip's larger blindside head formation. Large flange head style available upon request.

Stainless Rivet/Stainless MandrelHead Style Rivet Diameter Part No. Grip Range Pre-Drill Hole SizeDome 1/8" 1194553 .020-.192 #30 (.128-.133)Dome 1/8" 1194555 .059-.256 #30 (.128-.133)Dome 1/8" 1194558 .118-.315 #30 (.128-.133)Dome 5/32" 1194559 .020-.256 #20 (.161-.166)Dome 5/32" 1194580 .139-.354 #20 (.161-.166)Dome 5/32" 1194581 .276-.472 #20 (.161-.166)Dome 3/16" 1194582 .039-.236 #10 (.193-.199)Dome 3/16" 1194583 .197-.394 #10 (.193-.199)Dome 3/16" 1194584 .315-.472 #10 (.193-.199)

Head Style Rivet Diameter Part No. Grip Range Pre-Drill Hole SizeDome 1/8" 1194585 .039-.197 #30 (.130-.136)Dome 1/8" 1194586 .059-.256 #30 (.130-.136)Dome 1/8" 1194587 .118-.315 #30 (.130-.136)Dome 5/32" 1194589 .039-.256 #20 (.161-.166)Dome 5/32" 1194610 .138-.375 #20 (.161-.166)Dome 5/32" 1194611 .276-.512 #20 (.161-.166)Dome 3/16" 1194612 .039-.256 #10 (.193-.199)Dome 3/16" 1194613 .177-.433 #10 (.193-.199)Dome 3/16" 1194614 .256-.512 #10 (.193-.199)Dome 3/16" 1194615 .433-.768 #10 (.193-.199)Dome 3/16" 1194616 .630-.945 #10 (.193-.199)

Aluminum Rivet/Stainless Mandrel



Selection American Standard Blind Rivets Standard blind rivets are ideally suited for metal trim applications and other light gauge installations. SFS intec provides a selection of 1/8" diameter rivets painted to match standard industry colors. Other sizes and colors available upon request.

Aluminum Rivet/Aluminum MandrelHead Style Rivet Diameter US Dimension Part No. Grip Range Pre-Drill Hole SizeDome 1/8" 42 L0500 .063-.125 #30 (.129-.133)Dome 1/8" 43 L0520 .126-.187 #30 (.129-.133)Dome 1/8" 44 L0540 .188-.250 #30 (.129-.133)Dome 1/8" 46 1242922 .313-.375 #30 (.129-.133)Dome 1/8" 48 1242926 .376-.500 #30 (.129-.133)Dome 5/32" 52 L0620 .020-.125 #20 (.160-.164)Dome 5/32" 54 L0660 .188-.250 #20 (.160-.164)Dome 5/32" 56 1242929 .251-.375 #20 (.160-.164)Dome 5/32" 58 1242934 .376-.500 #20 (.160-.164)Dome 3/16" 62 1242935 .020-.125 #11 (.192-.196)Dome 3/16" 64 1242937 .126-.250 #11 (.192-.196)Dome 3/16" 66 L0760 .251-.375 #11 (.192-.196)Dome 3/16" 68 1242939 .376-.500 #11 (.192-.196)Dome 3/16" 610 1242940 .501-.625 #11 (.192-.196)Dome 3/16" 612 1242941 .626-.750 #11 (.192-.196)Dome 3/16" 614 1242943 .751-.875 #11 (.192-.196)Dome 3/16" 616 1242944 .876-1.00 #11 (.192-.196)Countersunk 1/8" 42 1242950 .092-.125 #30 (.129-.133)Countersunk 1/8" 43 1242951 .126-.187 #30 (.129-.133)Countersunk 1/8" 44 1242952 .188-.250 #30 (.129-.133)Countersunk 1/8" 45 1242953 .251-.312 #30 (.129-.133)Countersunk 5/32" 54 1242954 .188-.250 #20 (.160-.164)Countersunk 5/32" 56 1242955 .251-.375 #20 (.160-.164)Countersunk 3/16" 64 1242956 .188-.250 #11 (.192-.196)

White 001 White 014 Bright White 330 Warm White 348 Bone White 818 Sierra WhiteTan 020 TanBeige 109 Sand Beige 248 Light Stone 415 Beige 422 Taupe 548 IvoryBrown 110 Brown 230 Desert Brown 374 Dark BrownGreen 052 Teal Green 228 Green 232 Evergreen 385 Patina 660 Hemlock 732 Denali Green 798 Hartford Green 925 Classic GreenRed 074 Colonial Red 102 Crimson Red 393 Burgundy 691 Barn Red 890 Red 928 Terra CottaBronze 042 Burnished Slate 324 Dark Bronze 537 Medium BrownBlue 012 Blue 421 Navy 432 Blue Teal 843 Regal BlueGray 051 Charcoal Gray 091 Zinc Gray 302 Pearl Gray 416 Slate Gray 578 Old Town Gray 696 Pewter Gray 850 Ash GrayBlack 023 Black 507 Matte BlackMetallic 1160 Champagne Metallic 1161 Silver Metallic 1162 Zactique Metallic 1116 Copper Penny Metallic

Head Style Rivet Diameter US Dimension Part No. Grip Range Pre-Drill Hole SizeDome 1/8" 42 L0100 .063-.125 #30 (.129-.133)Dome 1/8" 43 L0120 .126-.187 #30 (.129-.133)Dome 1/8" 44 L0140 .188-.250 #30 (.129-.133)

Head Style Rivet Diameter US Dimension Part No. Grip Range Pre-Drill Hole SizeDome 1/8" 42 L1280 .063-.125 #30 (.129-.133)Dome 1/8" 43 L1290 .126-.187 #30 (.129-.133)Dome 1/8" 44 L1300 .188-.250 #30 (.129-.133)Dome 1/8" 46 L1320 .251-.375 #30 (.129-.133)Dome 1/8" 48 1243078 .376-.500 #30 (.129-.133)Dome 5/32" 52 1243079 .020-.125 #20 (.160-.164)Dome 5/32" 54 1243093 .126-.250 #20 (.160-.164)Dome 5/32" 56 1243097 .251-.375 #20 (.160-.164)Dome 3/16" 62 L1485 .020-.125 #11 (.192-.196)Dome 3/16" 64 1243098 .126-.250 #11 (.192-.196)Dome 3/16" 66 1243100 .251-.375 #11 (.192-.196)Dome 3/16" 68 1243104 .375-.500 #11 (.192-.196)

Steel Rivet/Steel Mandrel

Stainless Rivet/Stainless Mandrel

Blind Rivet Tools Installation Tools for Blind Rivets


ApplicationAccuBird 14.4 Volt Cordless Riveting Tool

PowerBird 14.4 Volt Cordless Riveting Tool

RV74G Electric (AC) Powered BULB-TITE Tool • The RV74G is the newest refinement in GESIPA

Electric Powered BULB-TITE installation tool that is designed for Metal Building Construction applications. This tool is suited to sidewall panel applications. Attaching the optional 74-EXT extension adapts the RV74G for installing BULB-TITE's in roofing applications from a standing position.

RV 74-EXT Pulling Head Extension Unit

• Attachment of the 74 EXT extension unit adapts the RV74G tool for roofing applications. This ergonomic feature enables BULB-TITE installation

while standing.

BULB-TITE Pulling Heads RV8840-X (5,6,8,9 Diameter BULB-TITE Rivets) • RV8840 series pulling heads are designed for use

with 6603, 8604, 8605 series BULB-TITE rivets which feature multi-grip type mandrels. • These heads are equipped with jaws and tips for specific diameter BULB-TITE rivets. The special BULB-TITE crown-swaging nose tip pivots to align the tip onto the BULB-TITE rivet's head crown for improved bore sealing of installed rivets.

RV24RE BULB-TITE Removal Tool

Weight: 4.8 lbs. (2.2 kg) Working Stroke: .79" (20 mm) Traction Power: 1,900 lbs. (6,500 N) Power Pack: 14.4 Volt, rechargeable Li-Ion / 1.3 Ah Part Number: 0836102 Battery Charger: 110V/60Hz, 60 minute charge time

Weight: 4.8 lbs. (2.2 kg) Working Stroke: .79" (20 mm) Traction Power: 2,900 lbs. (13,000 N) Power Pack: 14.4 Volt, rechargeable Li-Ion / 2.6 Ah Part Number: 0835558 Battery Charger: 110V/60Hz, 60 minute charge time

Work Capacity: 5/32", 3/16", 1/4" & 9/32" BULB-TITE Rivets* *Requires appropriate sized RV8840 series BULB-TITE pulling head. Weight: 6.5 lbs. w/ pulling head attached Length: 14" w/o pulling head, 18" w/ pulling head attached Traction Power: 3,000 lbs. Work Stroke: Continuous reciprocating .375" per cycle Part Number: 1195149

Weight: 1.5 lbs. Length: 12-13/16" (Extends tool by 12") Part Number: 1195154

Weight: 0.5 lbs. Length: 6 1/16" Part Number: 1195150 - Pulling Head - 5/32" Dia. 1195151 - Pulling Head - 3/16" Dia. 1195152 - Pulling Head - 1/4" Dia. 1195153 - Pulling Head - 9/32" Dia.

Designed for use with Aluminum BULB-TITE rivets, the tool greatly simplifies rivet removal in repair operations. The specially ground jaws cut rivet heads off cleanly without damage to the application material. Part Number: 1195162

Specify the BULB-TITE rivet diameter when ordering.

Blind Rivet Tools Installation Tools for Blind Rivets


ApplicationTaurus 1 Hydro-pneumatic Power Riveting Tool • Nose tips for each rivet diameter are stored in tool's base. • Same hydraulic section as the Taurus 2 ensures long tool life and reduced maintenance. • Suspension loop retracts into tool body.

Taurus 2 Hydro-pneumatic Power Riveting Tool

• New 3-piece jaw design increases jaw life – reducing service costs.

• Integrated mandrel collection system with grip release shutoff – conserves compressed air resources.

• Padded ergonomic tool grip enhances comfort – lowers operator fatigue.

Taurus 3 Hydro-pneumatic Power Riveting Tool • Taurus 3 is up to 40% lighter than comparable

tools in this power range. • Long working stroke installs multi-grip rivets in a single stroke. • Reliable exhaust-air mandrel ejection with large collector and saftey interlock.

Taurus 4 Hydro-pneumatic Power Riveting Tool

• Taurus 4 offers the high pulling force required for many of today's 1/4" diameter structural blind rivets.

Work Capacity: 1/8" ø in all materials Weight: 2.87 lbs. Pulling Strength: 1,150 lbs. @ 90 psi Working Stroke: .590 in. Part Number: 1167650

Work Capacity: Up to 3/16" ø in all materials Weight: 3.75 lbs. Pulling Strength: 2,500 lbs. @ 90 psi Working Stroke: .709 in. Part Number: 1195689

Work Capacity: Up to 1/4" ø in all materials and 9/32" Alum BT Weight: 4.19 lbs. Pulling Strength: 3,900 lbs. @ 90 psi Working Stroke: .984 in. Part Number: 1195690

Work Capacity: Up to 1/4" ø structural blind rivets and 9/32" Alum BT Weight: 4.4 lbs. Pulling Strength: 5,500 lbs. @ 90 psi Working Stroke: .750 in. Part Number: 1213032

• Allow for one side attachment of fiberglass panels through a pre-drilled hole.• Designed to pull fiberglass panels together without cracking the material.• Come assembled with EPDM washers for a weather tight seal.

Application Grommet FastenersMaterials: Neoprene rubber w/ molded brass nut

Size 3/8" Grommet: Part No. E0260-CSFastener: 10-32 x 1-1/4" stainless 5/16" AF Hex HeadWasher: 15 mm O.D stainless Bond Seal

Size 1/4" Grommet: Part No. E0080-CUFastener: 6-32 x 1-1/4" stainless 1/4" AF Hex HeadWasher: 12 mm O.D stainless Bond Seal


OptionsPainted



5 6 7 3 2 1 ?4



Grommet Fasteners Grommet fasteners attach fiberglass panels


ApplicationWG-7 ClosureMaterial Thickness: 1", 1-1/2", 2"Color: Black

WG-7™ Closure WG-7 closure and WG-7 adhesive closureFor panel opening filler

Closure and Venting Products

• The industry standard for closure material — time tested-millions of feet installed over the last 30-plus years.

• Polyethylene foam for exceptional strength and compressibility.

• Available with adhesive applied to the contact side of thepanel surface assures positive positioning during installation.

• Resist damaging ultra violet rays and ozone deterioration.• Over 1800 panel configurations available.• Manufactured in multiple plants for quick delivery.

Typical Inside Closure Application Typical Outside Closure Application

Technical Properties

Test Test Method Units Values

Density ASTM D3575 lb/ft³ 1.7 - 1.9 194 maxWorking Temperature Range Internal °F -76 min 25% 5.1Compression Deflection 50% ASTM D3575 psi 13.6 25% - 1/2 hr 15Compression Set 25% - 24 hr ASTM D3575 % max 6Tear Strength ASTM D3575 psi 11.5Tensile Strength ASTM D3575 psi 46.8Elongation ASTM D3575 % 165Flammability FMVSS302 4"/min PassShore Hardness ASTM D2240 OO 55

*Data represents typical values measured on 0.4" thick specimen and should be considered as a guidline only.

Pipe Flashing Square and round base pipe flashingFor roof pipe flashing


ApplicationSquare Base

Size Pipe size Base size1 1/4 – 2 -3/4" 4-1/2" Closed Top2 7/8 – 4" 6" 3 1/4 – 5-3/4" 8" Closed Top4 2-3/4 – 7" 10"5 4 – 8-1/4" 11"6 4-3/4 – 10" 12"7 5-1/2 – 11" 14"8 6-3/4 – 13-1/2" 17"9 9-1/2 – 20-1/2" 25"10 12 – 28-1/2" 34"

Round BaseSize Pipe size Base Size1 1/4 – 2-1/2" 4-3/4" Closed Top2 1-3/4 – 3" 6-1/4"3 1/4 – 5" 7-3/4" Closed Top4 3 – 6-1/4" 9-1/4"5 4-1/4 – 7-3/4" 10-3/4"6 5 – 9" 12-1/4"7 6 – 11" 14-1/4"8 7 – 13" 16-1/2"9 9 – 19" 25-1/2"

Retrofit Square BaseSize Pipe size Base Size1 1/2 – 4" 8-3/16"2 4 – 9-1/4" 14-1/4"3 9-1/4 – 16-1/4" 21-1/2"

Retrofit Round Base ZipperSize Pipe size Base Size1 3/4 – 2-3/4" 4-3/4"2 2 – 7-1/4" 10-3/4"3 3-1/4 – 10" 25-1/4"

• Pipe opening can be easily customized on job sight utilizing clearly marked pipe diameters on each flashing.

• EPDM and Silicone are both flexible materials, resistant to ultraviolet rays, cracking or weathering.

• Available in EPDM black or gray and silicone red.

• The aluminum base is corrosion resistant and conforms easily to any panel configuration or roof pitch.

• Retrofit flashing is available for piping with welded caps or cross bars.

• Colors available in standard square and round base pipe flashing.

Pipe Flashing Square and round base pipe flashingFor roof pipe flashing


ApplicationMulti-Flash Square Base

Size Standard Pipe size Retrofit Pipe size3 1/4 – 5 -3/4" 2 – 4-1/2"5 4 – 8-1/4" 3-1/2 – 6-3/4"8 6-3/4 – 13-1/2" 6-1/2 – 12"MAXI 12 – 28-1/2" 13 – 27"

Material SpecificationsTest Type EPDM Silicone (Hi-Temp)Advance ozone resistance 70 Hrs. 70 Hrs.test @ 500 pphm High temperature: Intermittent +275º F +500º F Continuous +212º F +437º FLow temperature: Resistance tested to -65º F -100º F Tensile strength 1450 psi 700 psi

OptionsColors Available

ProfileVent® Metal roofing ridge ventin a roll


• 40 year limited warranty

• Glue spots prevent slipping during installation

• Fits under any ridge cap

• Fits any pitch 2:12 – 20:12

• One person roll-out installation

• Won’t scratch panel finish

• Won’t crack, dent or rust during shipping or installation

• Won’t clog from airborne dust

• Prevents insect infiltration

• Prevents snow infiltration

• Provides proven roof ventilation

• Meets all model building codes

• Packing in English, French and Spanish

• No waste—use leftovers on next job

• Will not support a flame

• Made in U.S.A.

ApplicationProfileVent RollsNew or re-roof on Purlin or wood deck Construction:Use a 2" opening at the ridge to provide ventilation. On new or re-roof wood deck construction, cut a 2" slot at the ridge (1" each side, start cut 6" from gable ends). On purlin construction position panels to leave a 2" opening.

Available in convenient sizes• 20' package• 50' package• 100' package

Current panel profiles

1Allow 2" opening at ridge for ventilation. ProfileVent is rolled

out along the ridge, gable to gable, about 1" up-slope from the ridge cap edge. The positioning adhesive on most profiles will hold ProfileVent in position and allow for repositioning.

3Screw down or pop rivet the ridge cap according to manufacturer’s

instructions (works with any ridge cap).2ProfileVent can be cut with

scissors or utility knife.Inset: When splicing ProfileVent, make the splice at the center top of the high rib and use caulk or sealant along the splice.

3/4" Hi-RibR-PanelProfileVent matches most major OEM profiles.Call for Details.


ProfileVent® Metal roofing ridge ventin a stick

• For 3/4" Hi-Rib roofs

• 1" deep x 2" wide x 3' length

• Installs just like closure

• No release paper

• New improved adhesive

• Cut to fit profile

• Won’t dry out from exposure

• 24 pieces/carton — 72 linear feet

ApplicationProfileVent 3' StickNew or re-roof on Purlin or wood deck Construction:Use a 2" opening at the ridge to provide ventilation. On new or re-roof wood deck construction, cut a 2" slot at the ridge (1" each side, start cut 6" from gable ends). On purlin construction position panels to leave a 2" opening.

Current panel profiles 3/4" Hi Rib

1Allow 2" opening at ridge for ventilation. ProfileVent is

positioned along the ridge, gable to gable, about 1" up-slope from the ridge cap edge. The positioning adhesive on most profiles will hold ProfileVent in position and allow for repositioning.

3Screw down or pop rivet the ridge cap according to manufacturer’s

instructions (works with any ridge cap).2ProfileVent can be cut with

scissors or utility knife.Inset: When splicing ProfileVent, make the splice at the center top of the high rib and use caulk or sealant along the splice.

Ventco™ Ridge Cap Anchor Clip Ridge cap anchor clip


1Install your metal roofing panel according to manufacturer’s

instructions. Apply mastic above and below pre-drilled holes in the clip. Before installing ProfileVent®, insert #14A screw through the large down-slope access hole in top of the Ridge Cap Anchor Clip.

Anchor clips are recommended in high wind areas and on panels with major ribs 16" on center or greater.

Anchor Clip Detail

2Lift the back end of clip. Slip ProfileVent under the clip. Push

clip back down and insert another #14A screw in the up-slope hole.

ApplicationVentco™ Ridge Cap Anchor ClipAn independent engineering corporation tested the performance of the Ventco Ridge Cap Anchor Clip under high wind loading. During testing, a roof/ridge vent/cap system was subjected to wind speeds that follow the Dade County Test protocol.

The following observations were made concerning the performance and structural integrity of the clip and ridge cap:• No lifting of the ridge cap up to 115 mph• No fastener pull out or loosening• The ridge cap remained in contact with ventilation system• No difference in performance when the cap is secured

to the clip with screws or rivets

Specifications• 20 gauge galvanized steel• Visible surface painted black for aesthetic purposes

Packaging• 25 clips per small box• 24 small boxes per master box• 600 clips per master box

M90023/4" Anchor Clip

M90041" Anchor Clip

M90061-1/4" Anchor Clip




OptionsNone

Anchor Clip U.S. Pat. 6418678 (other patents pending)

Butyl Tape Sealant Tape


Meets or exceeds all requirements of:

• Military Spec MIL-C 18969B Type II Class B• Federal Spec TT-C 1796A Type II Class B• N.A.A.M.M. SS-1C-68• A.A.M.A. 804.1 AND 807.1• M.B.M.A. Ice Damming - Five-Inch static water head test• F.D.A. Regulations (#175.125)

• Designed for side and end lap sealing of metal panels, roof vents and pipe flashing

• Exceeds sealing requirements for AC, refrigeration and windows

• Extruded on silicone coated paper for easy application• Greater cohesive strength• Superior adhesion

• Withstands extreme roof temperatures• Superior low temperature compressibility• Cold flow resistant• Resistant to UV light• Contains anti-oxidants, fungicides and anti-bacterial agents• Seal not affected by normal movement of building• Wide service temperature range

Tested Physical Properties

Test Method Test Typical Results GSTM 10* Color Light GreyASTM D-217-68 Cone penetration @ 77°F/25°C, 55 105g/5sec. 1/10mmASTM C-771-74 Non-volatiles, % weight @ 212± 99+ 3°F/100±-2°CASTM D 792-66 Weight/gallon @ 77°F 12.9 lbs Weight/liter @ 25°C 1.50 kgASTM D 792-66 Specific gravity @ 77°F/25°C 1.55GSTM 11* Service temperature - range -60° to +275°F -51° to +135°CGSTM 16* Sag (3 weeks @ 160°F/71°C) NoneASTM C-765-73 Cold temperature flexibility 1/2" (12.7 mm) No cracking or Mandel Bend @ -60°F/-51°C loss of adhesionGSTM 9* Webbing and elongation: 1,050%+ @ 77°F/25°C 3,050%+ @ 32°F/0°CGSTM 1* Adhesive/cohesive failure mode @ 3%/97% 77°F/25°CASTM D-897-72 Tensile strength, p.s.i. @ 77°F/25°C 25ASTM D-750-68 Weatherability - 1,000 hours in Q.U.V. No discoloration weatherometer (Cycle of 8 hours cracking, crazing, or U.V. @ 150°F/65°C; then 4 hours of loss of adhesion condensation @ 104°F/40°C)

* GSTM test methods available upon request.

Application RecommendationSurfaces: All surfaces to be sealed should be free of dust, dirt, oil and moisture before applying sealant.

Temperature: Apply in dry conditions above 40°F (4°C); At temperatures below 40°F (4°C) atmospheric condensation surfaces inhibit adhesion and should be avoided.

Application: Apply MB-10A tape to surface directly from roll. Press sealant through the silicone release paper with a smooth, even hand motion. Note: for metal roofing and siding applications, place sealant under the fastener to prevent wind blown rain from leaking through the fastener holes.

SelectionSFS Part # Size Feet Per Roll Rolls/CartonV8000 3/16" Bead Butyl Sealant 25' Roll 48V8020 3/8" x 3/32" Butyl Sealant 45' Roll 48V8040 1/2" x 3/32" Butyl Sealant 50' Roll 20V8080 3/4" x 3/32" Butyl Sealant 50' Roll 14

Rolls are packed in water-resistant cartons.

Hannoband® BG1 Joint Sealant Tape


• Hannoband® BG1 is a pre-compressed, self-expanding polyurethane foam with acrylate dispersion impregnation

• Provides resistance to rain, wind, sound, draft and dust• Use for sealing joints and seams in metal panels, gaps around door and

window frames, and expansion joints in buildings• Pressure sensitive adhesive for fast and easy installation• Flame retardant

BG1 provides maximum environment protection by:• Greatly reducing air infiltration• Highest levels of resistance to wind driven rain• Superior sound proofing• Extended functional life• Highest fire rating• Smallest thermal change (temperature gradient) inside and outside of

sealed joint

Selection Compressed Expanded Joint Joint Width Roll

Part # Dimension Dimension Depth Max. Min. Length Packaging 1305091 1/4" x 1" 1" x 1" 1" 1/8" 1/4" 26.2 ft. 12 rolls/ctn 1305092 3/8" x 1" 1-1/2" x 1" 1" 1/4" 3/8" 18.4 ft. 12 rolls/ctn

Disposal Residue tape can be disposed of in the household waste. The local regulations are to be adhered to.

SafetyOn the basis of existing data and experience, the product is not hazardous in the meaning of the Hazardous Material Regulations. We recommend however that you take the same care and use the same hygiene as with chemical materials.

CleaningSkin cleansing with soap and water. The impregnate and/or adhesive residues is possible with a

petroleum-based cleaning agent. Please observe the safety regulations.

Technical Data

Property BG1

Color blackAir Tightness ASTM E 283 2,4 l/sm (360 Pa) (1,59 cfm/ft (7,5 psf)) 0,55 l/sm (75 Pa) (0,3 cfm/ft (1,57 psf))Resistance to water penetration ASTM E 331/E 547 ≥ 600 Pa (≥ 12,5 psf)Heat resistance -30°C - 90°C (-40°F - 194°F) Short Term: -40°C - 120°C (-40°F - 248°F)Tensile strength ASTM D3574/ISO 1798 > 100 kPa / > 14 psiElongation ASTM D3574/ISO 1798 > 200%Compression force ASTM D3574/ISO 3386 3,4 kPa / 0,49 psi, 40% compressionDensity ISO 845 65 kg/m³ ± 10% (4 lb/ft³)Thermal Conductance DIN EN 12667 λ = 0,0429 W/mkShelf Life 18 months from date of production

Novaflex® Metal Roof Sealant


Novaflex® metal roof sealant provides unbeatable adhesion to mostcommon construction materials, including Kynar®

• Non-corrosive, single component, oxime cured silicone sealant and/or adhesive• Applications include metal roofs and siding, wood, galvanized steel, flashing, aluminum, PVC, windows and masonry• Tack free in 10 minutes; completely cured in 2 days• Permanently flexible; will not shrink, crack, sag or slump• Provides a waterproof, weather tight seal• Extrudes down to 0°F• Will not freeze

* The values outlined reflect testing that was conducted on laboratory prepared specimens, actual results may vary.The information provided in the above table is not intended for use in preparing specifications. Please consultmanufacturer for additional information.

Product Specifications

Physical Property Test Method Performance Range

Appearance Colored pasteExtrusion Rate 1/8" Orifice @ 50 psi 30 - 80 gramsSkin Over Time 3/8" @ 50%RH & 77° F 5 - 10 minutesThrough Cure 3/8" @ 50%RH & 77° F 24 hours

Technical Properties*

Physical Property Test Method Typical Value

Specific Gravity 1.00 - 1.25Tensile Strength ASTM D412 140 - 200 psiElongation ASTM D412 500 - 650%Tear Resistance ASTM D 624 30 - 35 pli Shore Hardness ASTM D 2240 22 ± 8Service Temperature -40° C - 205° C (-40°F - 400° F) Type SJoin Sealant Designation ASTM C920 Grade NS Class 25 Use NT, M, G, A, OAdhesion Glass 12 - 15 pli Aluminum ASTM D 903 10 - 14 pli Vinyl 12 - 15 pli


Novaflex® Metal Roof Sealant


Selection Novaflex Novaflex

Part # Sealant Color Part # Sealant Color 1305155 White 1305164 Sandstone

1305156 Almond 1305165 Red

1305157 Dark Bronze 1305166 Brown

1305158 Black 1305167 Green

1305159 Sierra Tan 1305168 Antique White

1305161 Medium Bronze 1305169 Translucent

1305162 Light Gray 1305170 Charcoal Gray

1305163 Hemlock Green 1305171 Gutter Gray

Packaging• Tube size and dimension: 10.3 fl. oz. (304 ml); 9" x 2" x 2"• Case size: 12 tubes per case; weight - 20 lbs.• Sold in case quantity only

Installation• Cures times of materials listed on this sheet are dependent upon environmental conditions

such as temperature, humidity and application thickness• Adhesion should be checked on small samples prior to full-scale application• Can be used on interior and exterior• Removable tips - no wasted sealant left in fixed tips• No waste; ability to use entire tube, or can save with end cap• Not paintable

Safety Advantages and Precautions• Low odor• Solvent free• VOC Compliant in all 50 states• Not recommended for surfaces that are to be painted• Not recommended for joints submerged under water• Do not install if surface temperature is below 0° F or exceeds 120° F• Obey all local, state and federal regulations for proper disposal of solvent and silicone waste

StorageShelf life of 18 months from date of manufacture when stored in the original, unopened containerat 75° F or less

ApplicationDI 600 Power ScrewdriverFor installing self-drilling fastenersFeature: Versa clutch system

CF 50 Setting Nose PieceInstallation tool with depth locator for long SX composite panel fastenersFeatures:ZA 1/4"/80 drive shaftE 380 drive socket

irius® Drive SocketThe E-420 setting tool is required for installing the irius drive systemThe fasteners are clamped firmly via the teeth under the fastener head

Hex and Torx® Drive Bits

0973316 irius Drive Bit (E420)J0865 1/4" x 2-9/16" x 1/4" Lobular Hex Drive Mag SocketJ0984 1/4" x 1" x 1/4" Lobular Hex Drive Mag SocketJ0875 5/16" x 2-9/16" x 1/4" Lobular Hex Drive Mag SocketJ0925 3/8" x 2-9/16" x 1/4" Lobular Hex Drive Mag SocketJ0945 No. 3 Sq. Recess Drive Bit J0955 2/2 Quadrex x 3" x 1/4" Hex DriveJ6900 1/4 Hex Magnetic Bit Holder0895280 T20W TORX Drive Bit J6800 T25 TORX Drive Bit 1"J2020 T25 TORX Drive Bit 1-5/16"0514261 SFS T-25 TORX Special For Evergrip0761878 T30 TORX Drive Bit

(RH2) Product Name: #14 (RH3) Description: #3 Phillips Drive(RH4) Application: Insulation board to roof cover.Installation Screw Guns Installation screw guns and drive sockets

Installation tools

Tools and Accessories

• Screw guns and noise pieces are matched for individual products to insure consistent installation performance.

• Screw gun manufactures and individual tools are tested and pre-qualified for reliable field performance before recommendation.

Volts: 110Amps: 6.5Speed: 0 – 2000 rpm variable speed

Socket E-420E-420 parts kitSpare jaws

webstore

Typewritten Text

Distributed by: BEST MATERIALS ® LLC Ph: 800-474-7570, 602-272-8128 Fax: 602-272-8014 www.BestMaterials.com Email: [email protected]

http://www.bestmaterials.com/


Documents

Best · PDF fileexceeding the life of the proposed project. Fastener Materials. ... Fastener Design. BEST MATERIALS ® | Email: [email protected] |