Upload
hirdesh-daswani
View
225
Download
0
Embed Size (px)
Citation preview
8/3/2019 Bel Sample Soln
1/23
1. The noise figure of a receiver is a measure of:1. Excess noise generated2. Bandwidth of the receiver3. Gain of the receiver4. Operating frequency
2. The ratio receiver is:1. Direct detection type2. Super regenerative type3. Super heterodyne type4. None of these
3. In an amplitude modulation system, the modulationindex is dependent upon:
1. Modulating frequency only2. Carrier amplitude only3. Modulating signal amplitude only4. Modulating and carrier amplitudes only
4. Image rejection mixer is generally used:1. To reject the unwanted signal2. To improve signal amplitude3. To improve noise figure4. To improve conversion loss
5. The value of a resistor creating thermal noise isdoubled. The noise power generated is therefore:
1. Halved2. Quadrapuled3. Doubled4. Unchanged
6. Indicated the false statement:1. HF mixer are generally noisier than HF amplifier2. Impulse noise voltage is independent of
bandwidth3. Thermal noise is independent of the frequency at
8/3/2019 Bel Sample Soln
2/23
which it is measured4. Industrial noise is usually of the impulse type
7. If the carrier of a 100 percent modulated AM wave issuppressed the percentage power saving will be:
1. 50 b. 70 c. 100 d. 66.6
8. A balanced modulator produces:1. The carrier and Two side bands2. The carrier and one side band3. Two side bands alone
4. Carrier and a number of side bands9. The frequency deviation in FM system is proportionalto:
1. Modulating frequency2. Carrier amplitude3. Modulating signal amplitude4. None of these
10. In FM, the total transmitted power is:1. Dependent on modulating signal amplitude2. Dependent on modulating frequency3. Dependent on modulating index4. Independent of the above
11. The carrier in an FM system disappears for the
lowest modulation index of:1. 0.5 b. 1.0 c. 2.4 d. 3.5
12. The difference between phase and frequencymodulation:
1. Is purely theoretical because they are the samein practice
2. Is too great to make the two systems compatible
3. Lies in the poorer audio response of phasemodulation
8/3/2019 Bel Sample Soln
3/23
4. Lies in the different definition of the modulationindex
13. The overall noise figure of two cascaded amplifiers isequal to
1. The algebraic sum of the two2. The sum of the squares of the two3. The square root of the product of the two4. None of these
14. The noise power output of an amplifier is equal to:
1. KTo BFG2. KTo FG3. KTo F/G4. KTo / FG
15. The effective noise temperature of an amplifier isequal to
1. (F + 1) To
2. FTo3. (F " 1) To4. None of these
16. The noise figure of an amplifier depends upon1. Its bandwidth2. Its gain3. Its operating frequency
4. None of these
17. The velocity of electromagnetic wave in a coaxialcable is
1. Equal to the velocity in free space2. Less than the velocity in free space3. Greater than the velocity in free space4. None of these
18. The standing wave ratio [SWR] in a transmission line:
8/3/2019 Bel Sample Soln
4/23
1. Is proportional to the load impedance2. Is dependent on the source impedance3. Is a mis-match between the load and line4. Is a measure of its power handling capability
19. The standing wave ratio (SWR) is unity in atransmission line if
1. The load impedance is equal to the characteristicimpedance of the line
2. The load impedance is twice that of thecharacteristic impedance
3. The load impedance is half of the characteristicimpedance of the line4. None of these
20. The standing wave voltage node along a line repeatsat the rate of if L is the wave length
1. L/4 b.L/2 c.L d.2L
21. A quarter wave line when short circuited at the farend behaves like1. Pure inductor2. Pure capacitor3. Parallel tuned circuit4. Series tuned circuit
22. The stub line used to match transmission line with a
given load impedance is generally1. Another open circuited line2. Another short circuited line3. Quarter wave transmission line4. Half wave transmission line
23. The smith chart generally covers a distance of1. Quarter wavelength
2. Half wavelength3. One wavelength
8/3/2019 Bel Sample Soln
5/23
4. Twice the wavelength
24. The component generally used to sample a portion ofthe energy transmitted in a line is
1. Isolator2. Circulator3. Directional coupler4. None of these
25. The return loss in a transmission line is a measure of1. Loss of the line
2. Standing wave ratio3. Characteristic impedance of the line4. None of these
26. The antenna can be considered as1. Matching the source and free space2. Matching the source to the line3. Matching the line and free space
4. None of these
27. The free space impedance is approximately equal to1. 177 W2. 277 W3. 377 W4. 50 W
28. The polarization refers to1. The physical orientation of the radiated wave2. The directional of propagation of the wave3. Direction perpendicular to the propagation of the
wave4. None of these
29. If u & e are the permeability and permittivity
respectively the characteristic impedance of the mediumis given by
8/3/2019 Bel Sample Soln
6/23
1. ue b. -u/e c. -e/u d. -eu
30. The power density at distance 'r' from an isotropicradiator with transmitted power P is:
1. P/r22. P/2 p r23. P/4 p r24. None of these
31. Frequencies in the UHF range is normally propagatedby means of
1. Ground waves2. Sky waves3. Surface waves4. Space waves
32. As electromagnetic waves travel in free space, onlyone of the following can happen to them
1. Absorption
2. Attenuation3. Reflection4. Refraction
33. High frequency waves are1. Absorbed by the F2 layer2. Reflected by the D layer3. Affected by the solar cycle
4. Capable of use for long distancecommunications on the moon
34. Indicate which one of following terms applies totroposcatter propagation
1. SIDS2. Fading3. Fraday rotation
4. Atmospheric storms
8/3/2019 Bel Sample Soln
7/23
35. When microwave signals follow the curvature of theearth, this in known as
1. Faraday effect2. Ducting3. Ionospheric reflection4. Tropospheric scattering
36. An ungrounded antenna near the ground:1. Is unlikely to need an earth mat2. Acts as a single antenna of twice the height3. Must be horizontally polarized
4. Acts as an antenna array37. One of the following consists of non-resonantantenna:
1. The folded dipole2. The rhombic antenna3. The end fire array4. The broad side array
38. Balun is:1. A circuit element to connect balance line to
unbalanced antenna or line:2. A circuit element to connect balance line to
balanced line3. A circuit element to connect unbalance line to
unbalanced line
4. None of these
39. The slotted line is used to measure:1. Standing wave ratio2. Load impedance3. Source impedance4. None of these
40. In amplitude modulation Ec ( 1 + m Sin Wmt) SinWot, each side band amplitude will be:
8/3/2019 Bel Sample Soln
8/23
1. Ecm/22. Ecm3. Ec/m4. 2Ec/m
41. FM modulation becomes equivalent to AMmodulation if
1. FM index is greater than 12. FM index is equal to 13. FM index is very much less than 14. FM index less than or equal to 1
42. S/N improvement of FM over AM, B is the FMmodulation index
1. 3B2 b.B c.2B d.B/2
43. Picture transmission in TV employs1. Suppressed carrier modulation2. Vestigial side band
3. Single side band4. None of these
44. Sound transmission in TV employ1. Amplitude modulation2. Phase modulation3. Frequency modulation4. Pulse amplitude modulation
45. One of the following is an indirect way of generatingFM this is the:
1. Reactance FET modulator2. Varacter divide modulator3. Amstrong modulator4. Reactance bipole transistor modulator
46. The modulation index of AM wave is changed from 0to 1. The transmitted power is
8/3/2019 Bel Sample Soln
9/23
1. Un-changed2. Halved3. Doubled4. Increased by 50%
47. The isotropic antenna is represented by1. Dipole antenna2. Rhombic antenna3. Yagi uda antenna4. No such antenna exists in practice
48. The gain of parabolic reflector antenna isproportional to1. The diameter of the reflector2. Square of the diameter of the reflector3. Aperture area of the feed4. None of these
49. The parabolic reflector antenna are generally used to
1. Provide high gain2. Provide pencil beam3. Increase bandwidth of operation4. None of these
50. Cassegrain feed is used with a parabolic reflector to1. Increase gain of the system2. Increase the bandwidth of the system
3. Reduce the size of the main reflector4. Allow the feed to be placed at a convenient point
51. A helical antenna is used for satellite trackingbecause of its
1. Circular polarization2. Maneuverability3. Broad bandwidth
4. Good front " to " back ratio
8/3/2019 Bel Sample Soln
10/23
52. The discone antenna is1. A useful direction finding antenna2. Used as a radar receiving antenna3. Circularly polarized like other circular antenna4. Useful as a VHF receiving antenna
53. Waveguides are used mainly for microwave signalsbecause
1. They depend on straight line propagation whichapplies to microwaves only
2. Losses would be too heavy at lower frequencies
3. There are no generators powerful enough toexcite them at lower frequencies4. They would be too bulky at lower frequencies
54. The wavelength in a waveguide1. Is greater than in free space2. Depends only on the waveguide dimensions and
the free-space wavelength
3. Less than the free space wavelength4. Equal to the free space wavelength
55. The dominant mode of propagation is preferres withrectangular waveguide because(indicate false statement)
1. It leads to the smallest waveguide dimensions2. The resulting impedance can be matched
directly to coaxial lines
3. It is easier to excite than the other modes4. Propagation of it without any spuriousgeneration can be ensured
56. The velocity of propagation (group velocity) in awaveguide is
1. Less than the free space velocity2. Greater than the free space velocity
3. Equal to be free space velocity4. None of these
8/3/2019 Bel Sample Soln
11/23
57. A wave can propagate in a waveguide if its cut offwavelength is
1. Greater than the free space wavelength2. Less than the free space wavelength3. Equal to be free space wavelength4. None of these
58. The dominant mode in a rectangular waveguide is1. TE11 b. TE10 c.TE20 d.TM11
59. The characteristic wave impedance of a waveguide1. Depends on the mode of propagation2. Does not depend on the mode of propagation3. Is same as the free space impedance4. None of these
60. A choke flange may be used to couple twowaveguides
1. To help in the alignment of the waveguides2. Because it is simpler than any other joint3. To compensate the discontinuities at the joint4. To increase the bandwidth of the system
61. The dominant mode in a circular waveguide is1. TE01 b.TE11 c.TM01 d.TM11
62. A ferrite is1. A non-conductor with magnetic properties2. An inter metallic compound with particularly
good conductivity3. An insulator which heavily attenuates magnetic
fields4. A microwave semiconductor invented by farady
63. The maximum power that may be handled by aferrite component is limited by the
8/3/2019 Bel Sample Soln
12/23
1. Curie temperature2. Saturation magnetization3. Line width4. Gyro magnetic resonance
64. The isolator is1. Bidirectional2. Unidirectional3. Used to tap the power in a waveguide
transmission line4. Used for None of these of the above
65. Isolator is generally used:1. To protect the high power transmitter2. To protect receiver3. To protect the antenna4. To avoid arcing in waveguides
66. A TR tube is used
1. To protect the high power transmitter2. To protect receiver3. To avoid arcing in waveguides4. For None of these of the above
67. Rieke diagrams are used to select best operatingconditions for
1. TWT amplifier
2. Klystron oscillator3. Magnetron oscillator4. Cross field amplifiers
68. The gain bandwidth product of a microwavetransistor FT, is the frequency at which the
1. Alpha of the transistor falls by 3 dB2. Beta of the transistor falls by 3 dB
3. Beta of the transistor falls to unity4. Power gain of the transistor falls to unity
8/3/2019 Bel Sample Soln
13/23
69. The cavity magnetron uses strapping to
1. Prevent mode jumping2. Prevent cathode-back heating3. Ensure bunching4. Improve the phase-focussing effect
70. The transferred " electron bulk effect occurs in1. Germanium2. Gallium arsenide3. Silicon
4. Metal semiconductor junction71. One of the following is not used as a microwave mixeror detector
1. Crystal diode2. Schottky " barrier diode3. Backward diode4. PIN diode
72. SAW devices may be used as:1. transmission media like stripline2. filters3. UHF amplifiers4. Oscillators at millimeter frequencies
73. Surface acoustic waves propagate in:
1. Gallium arsenide2. Indium phosphide3. Stripline4. Quartz crystal
74. A parametric amplifier has an input and outputfrequency of 2.25 GHz, and is pumped at 4.5 GHz is a
1. Traveling wave amplifier
2. Degenerate amplifier3. Lower-side band up converter
8/3/2019 Bel Sample Soln
14/23
4. Upper-side band up converter
75. The negative resistance in a tunnel diode1. Is maximum at the peak point of the
characteristic2. Is available between the peak and valley points3. Is maximum at the valley point4. May be improved by the reverse bias
76. Microwave links repeaters are typically 50KM apart1. Because of atmospheric attenuation
2. Because of output tube power limitations3. Because of Earth's curvature4. To ensure that the applied voltage is not
excessive
77. Microwave links are generally preferred to coaxial fortelevision transmission because
1. They have less overall phase distortion
2. They are cheaper3. Of their greater bandwidths4. Of their relative immunity to impulse noise
78. A geostationary satellite1. Is motionless in space(except for its spin)2. Is not really stationary at all, but orbits the earth
with a 24 hour period
3. Appears stationary over Earth's magnetic pole4. Is located at a height of 35800KM to ensureglobal coverage
79. The geostationary satellite launched by India arecalled
1. INTELSAT2. INSAT
3. COMSAT4. MARISAT
8/3/2019 Bel Sample Soln
15/23
80. A parametric amplifier must be cooled
1. Because parametric amplification generates a lotof hest
2. To increase bandwidth3. Because it cannot operate at room temperature4. To improve the noise performance
81. If the peak transmitted power in a Radar system isincreased by a factor of 16, the maximum range will beincreased by a factor of
1. 2 b. 4 c.8 d. 1682. Telephone traffic is measured
1. With echo2. By relative congestion3. In terms of the grade of service4. In erlangs
83. If the antenna diameter in a radar system isincreased by a factor of 4, the maximum range will beincreased by a factor of:
1. -2 b. 2 c. 4 d. 8
84. A high PRF will (indicate the false statement)1. Make the returned echoes easier to distinguish
from noise
2. Make target tracking easier with conicalscanning3. Increase the maximum range4. Have no effect on the range resolution
85. The bandwidth of a radar receiver is inverselyproportional to the
1. Pulse width
2. Pulse repetition frequency3. Pulse interval
8/3/2019 Bel Sample Soln
16/23
4. Square root of the peak transmitted power
86. If d is the pulse width, T is pulse repetition periodand P is the peak power, the duty ratio is
1. T/d b.P/T c.P/d d.d/T
87. If d is the duty ratio and P is the peak power in apulsed transmitter, then the average power is
1. P.d b. P.2d c.P/d d. P/2d
88. If the return echo arrives after the allocated pulse
interval1. It will interfere with operation of the transmitter2. The receive might be overloaded3. It will not be received4. The target will appear closer than it really is
89. If the target cross section is changing, the bestsystem for accurate angle traking is
1. Lobe switching2. Sequential lobing3. Conical scanning4. Monopulse
90. After a target has been acquired the best scanningsystem for tracking is
1. Nodding
2. Spiral3. Conical4. Helical
91. The Doppler frequency increases as the target1. Approaches the radar2. Recedes the radar3. Moves perpendicular to the beam
4. Does not depend on the target velocity
8/3/2019 Bel Sample Soln
17/23
92. The Doppler effect is used in (indicate the falsestatement)
1. Moving target plotting on the PPI2. MTI system3. FM Radar4. CW Radar
93. Solution to the blind speed problem is to1. Change the Doppler frequency2. Vary the PRF3. Use monopulse
4. Use MTI94. The A-scope displays
1. Target position and range2. Target range but not position3. Target position but not range4. Neither range nor position but only velocity
95. In the colour television system the sub carrierfrequency in MHz is approximately1. 3.58 b.4.5 c. 45.75 d. 5.58
96. In television 4: 3 : represents1. The interlace ratio2. The maximum horizontal deflection3. Aspect ratio
4. The ratio of the two diagonals of picture tube
97. Equalizing pulses in TV are sent during the:1. Horizontal blanking2. Vertical blanking3. The serrations4. Horizontal retrace
98. The number of lines per field in Indian televisionsystem is:
8/3/2019 Bel Sample Soln
18/23
1. 625 b. 312.5 c. 525 d. 262.5
99. The number of frames in Indian TV system is:1. 50 b. 60 c. 25 d.30
100. In a TV receiver the colour killer:1. Cuts off the chromastages during monochrome
reception2. Ensures that no colour is transmitted to
monochrome receivers3. Prevents colour overloading
4. Makes sure that the colour burst is notmistaken for sync pulses
Answer:-
1. a
2. c
3. b
4. c
5. b
6. b
7. d
8. c
9. c
10. d
11. c
8/3/2019 Bel Sample Soln
19/23
12. d
13. d
14. a
15. c
16. d
17. b18. c
19. a
20. b
21. c
22. b
23. b
24. c
25. b
26. c
27. c
28. c
29. b
8/3/2019 Bel Sample Soln
20/23
30. c
31. d
32. b
33. c
34. b
35. b
36. d
37. b
38. a
39. a
40. a
41. c
42. a
43. b
44. c
45. c
46. d
47. d
48. b
8/3/2019 Bel Sample Soln
21/23
49. b
50. d
51. a
52. d
53. d
54. a55. b
56. a
57. c
58. b
59. a
60. b
61. c
62. a
63. a
64. b
65. a
66. b
8/3/2019 Bel Sample Soln
22/23
67. c
68. a
69. d
70. b
71. d
72. b
73. d
74. b
75. b
76. c
77. a
78. b
79. b
80. d
81. d
82. a
83. c
84. c
85. a
8/3/2019 Bel Sample Soln
23/23
86. d
87. a
88. d
89. d
90. c
91. a92. a
93. b
94. b
95. a
96. c
97. b
98. b
99. a
100.a