Before using for the first time Operation Drying Changing the programme sequence Fragrance flacon

This dryer has 2 places for inserting fra-grance flacons. Use one or both when-ever you want to add a pleasant fra-grance to your laundry.

ɔ Close the unused socket.

ɔ Before using a fragrance fla-con, please read "Warning and Safety instructions - Using a fragrance flacon (optional accessory)" and "Fragrance flacon" in the operating instructions.

Inserting a fragrance flacon1. 2.

3. 4.

Markers and must line up with each another.

5. 6.

ĺ Turn the outer ring clockwise a little.

Markers and must line up with each other.

Before drying ĺ Turn the outer

ring clockwise a little.

The further you open the flacon, the more intense the fragrance.

After dryingTo avoid the fragrance escaping need-lessly:

ĺ Turn the outer ring anti-clock-wise until marker is in position .

If you want to dry laundry without add-ing fragrance: Remove the fragrance fla-con and store it in its original packaging.

Before cleaning the fluff filters

ĺ Remove the fragrance flacon. ĺ Only store the fragrance flacon in its original packaging

ɔ Never lay the fragrance flacon down. Otherwise, the fragrance will leak out.

M.-

Nr.

11 0

15 6

90/0

0TC

J 69

0 W

Pen

- A

U, N

Z

ɔ Before using the tumble dryer for the first time, ensure that it is correctly installed and connected.

After installation, a downtime of 1 hour is required before connecting the tumble dryer to the electricity supply. Otherwise the heat pump can be damaged.

It is essential to read the operating instruc-tions.

Energy saving tips

To avoid unnecessarily long drying times and high consumption of energy: – Make sure your laundry is spun at the maximum spin speed before drying.

– Clean the fluff filters in the door and in the door opening after every drying cycle.

– Load according to the optimum amount of laundry recommended for the programme being used. This will mean that the energy consumption for the amount of laundry is at its most economical.

– Make sure the room temperature is not too high.

– If there are other heat producing appli-ances in the room in which the tumble dryer is located, make sure the room is well-ventilated and switch the other appliances off, if possible.

1. Notes on correct laundry care ɔ Ensure that any foreign objects, e.g. detergent dis-

pensing balls, lighters, etc. have been removed from the laundry. Such items could melt or explode and cause damage to the dryer or the laundry.

ĺ Sort the laundry according to the type of fibre and weave, size, garment care label symbol and the drying level required.

ĺ Disentangle the laundry. ĺ Check seams and stitching to ensure that padding and linings are intact.

ĺ Fasten duvet covers and pillow cases to prevent small items from being rolled up inside them.

ĺ Fasten hooks and eyes. ĺ Tie together textile belts and apron ties. ĺ Sew in or remove loosened underwiring from bras.

OP

ER

ATIO

N

DR

YIN

G

CH

AN

GIN

G T

HE

PR

OG

RA

MM

E S

EQ

UE

NC

E

1 Control panel The control panel consists of a display and various sensor controls.

2 Display Different values are displayed and/or selected in the display.

3 Sensors The values in the display can be changed with the sensors.

4 OK sensor The OK sensor is used to confirm selected values.

5 Perfect Dry indicator With programmes with a selectable drying level, the Perfect Dry system calculates the residual moisture present in the laundry to ensure a precise dry-ing result. The display flashes at the beginning of the programme and lights up towards the end of the programme.

6 Optical interface For service technicians.

7 Sensor controls for Extras You can supplement the drying pro-grammes with Extras.

8 Sensor You can use the sensor to call up an energy consumption forecast for the selected drying programme.

9 Sensor The sensor starts the Delay start func-tion.

10 Start/Stop sensor Touching the Start/Stop sensor starts the selected programme or cancels a pro-gramme that has already started.

11 Programme selector For selecting programmes and switch-ing the washing machine off. The dryer is switched on by selecting a programme, and switched off by turning the pro-gramme selector to the position.

Operating the sensor controlsThe sensor controls react to fingertip con-tact. Selection is possible as long as the respective sensor is illuminated.If a sensor is brightly lit this means: currently selectedIf a sensor is dimly lit this means: selection possible

Switching on the tumble dryer ĺ Turn the programme selector to a pro-gramme.

The welcome tone will sound and the wel-come screen will light up. The display will guide you through the initial commissioning process, which is divided into several steps.For further information, please refer to the separate operating instructions.

2. Selecting a programme ĺ Turn the programme selector to a programme.

The interior drum lighting will come on.

Programme selectionThere are three possible ways to select a programme:

1. Selecting standard programmes via the programme selector ĺ Turn the programme selector to the required pro-gramme. The selected programme will appear in the display. This will then be replaced by the standard display.

2. Selecting further programmes via the "Further programmes/" setting and the display: ĺ Turn the programme selector to the Further program-mes/ position. The following will appear in the display: Warm air

ĺ Touch the sensors until the programme you want appears in the display.

ĺ Confirm the programme with the OK sensor.

3. Selecting programmes via the MobileControl  and the Miele@mobile App ĺ Turn the programme selector to the MobileControl posi-tion.

ĺ Follow the instructions in the display. ĺ Touch the Start/Stop sensor.

The dryer can now be operated via a mobile device together with the Miele@mobile App.

EcoFeedbackYou can use the sensor to call up an energy consumption forecast for the selected drying programme. ĺ Touch the sensor.

The estimated energy consumption will be displayed as a bar chart.

Delay start/SmartStartDelay startWith Delay start you can delay the start of a programme. The start of the programme can be delayed from 15 minutes up to a maximum of 24 hours.SmartStart (available in selected countries)The SmartStart function lets you define a time period during which your dryer will start automatically. The dryer will start on receipt of a signal, e.g. from your energy supplier, that indicates that the electricity rate is particularly economical.

5. Starting the programme ĺ Touch the flashing Start/Stop sensor.

The Start/Stop sensor will light up and the programme will start.

Emptying the condensed water container

Empty the condensed water container after every drying programme.

Empty container See will light up in the display if the maximum level of the con-densed water container is reached To turn the message off: Open and close the door while the dryer is switched on.

ĺ Pull out the condensed water container.

ĺ To prevent water running out, keep it in a horizontal position when carrying it. Hold it at the front and towards the back.

ĺ Empty the container.

ĺ Replace the con-tainer in the dryer.

ɔ Do not drink condensed water. It can cause health problems in people and ani-mals.

You cannot change to another programme once a programme has started (this pre-vents unintentional alterations). If you move the programme selector, Cannot be changed will light up in the display until you move the programme selector back to the original programme.Exception: The dryer can be switched off by turning the programme selector to the position.You will need to cancel the current pro-gramme before you can select a new one.

Cancelling a programme ĺ Touch the Start/Stop sensor. Cancel programme will light up in the dis-play.

ĺ Confirm with the OK sensor.As soon as Program cancelled lights up: ĺ Turn the programme selector to .

The current programme can also be cancelled in this way ĺ Turn the programme selector to . ĺ Select a programme. ĺ Touch the Start/Stop sensor.

The drying cycle starts.

Adding or removing laundry

ɔ Bear in mind that hot steam may escape when the door is opened.

ĺ Pull open the door. ĺ Add or remove items. ĺ Close the door. ĺ Touch the Start/Stop sensor.

The programme will start.

Programme durationAltering the programme sequence can cause the programme duration shown in the time display to be adjusted.

6. End of programme - unloading the drum

The program is finished when Finish/ Anti-crease or Finished appears. The Start/Stop sensor light goes out. – To save energy, 10 minutes after the end of the programme the Start/Stop sensor will begin to flash slowly and the display will go out.

– The tumble dryer switches off automati-cally.

ɔ Do not open the door before the end of the programme.

ĺ Open the door.

ĺ Remove the laundry.

ɔ Check that all items have been removed from the drum. If items are left in the dryer, they could be damaged by overdrying when the dryer is used the next time.

If the dryer is switched on at the mains and the door is opened, the drum lighting will come on. It will go out after a few minutes to save energy. ĺ Turn the programme selector to . ĺ Clean the fluff filters. ĺ Close the drum door. ĺ Empty the condensed water container.

4. Selecting programme settings

Programmes with drying levelsCottons, Minimum iron, Delicates, Pre-ironing, Shirts, Express, Denim, Outerwear, Sportswear, Steam care, Bed linen, Automatic plusThe pre-set drying level for the programme can be changed if required. ĺ Touch the or sensors to change the drying level.

Timed drying programmes and other programmesWarm air, Cool air, Basket programmeYou can change the duration in ten-minute increments. ĺ Touch the or sensors to change the duration.

Cottons, Woollens handcare, Pillows, Proofing, Silks handcareThe drying result is preset by the dryer and cannot be altered.

Selecting Extras ĺ Touch the sensor for the Extra you want. It then lights up brightly.

Freshen upFor removing or reducing odours in clean (dry or damp) clothing.Gentle tumbleLow temperature drying for delicate fabrics with the symbol on the care label, e.g. acrylic garments. Anti-creaseThis helps prevent creasing if the laundry is not removed immediately after the end of the programme.BuzzerAcoustic signal at the end of a programme.

3. Loading the tumble dryer ĺ Open the door. ĺ Unfold the laundry and load

loosely into the drum.

ɔ Do not overload the drum. Overloading can cause unnec-essary wear and tear of the laun-dry, give a disappointing drying result and cause more creasing.

ɔ If you are not using a fra-grance flacon: the tabs must be pushed down completely (see arrow) to ensure both sockets are closed.

ɔ When closing the door, make sure that laundry does not get trapped in the door opening.

ĺ Shut the door with a gentle swing.

1 Condensed water container – empty after each drying programme – Steam care programme: Note –min– marker

2 Door3 Control panel4 Access panel for the heat exchanger and plinth filter

– do not open during drying5 Cool air intake grille

– do not obstruct with a laundry basket or other objects

en - AU, NZ M.-Nr. 11 015 690

Quick Start GuideHeat pump tumble dryer

These short instructions are not a substitute for the operating instructions supplied with the appliance. Please read the operating instructions supplied with your tumble dryer before using it for the first time and take note of the Warning and Safety instructions, as well as the full descriptions on how to use your appliance.

Cleaning and care Problem solving guide

Fluff filters

Removing visible fluff

Clean the fluff filters in the door opening after every drying cycle.

ɔ Remove the fragrance flacon (if fitted).

ĺ Pull the upper fluff filter forwards to remove it.

ĺ Use your fin-gers or a vac-uum cleaner to remove the fluff from the surface of the filter.

ĺ Push the upper fluff filter back into posi-tion until it clicks.

ĺ Close the door.

Cleaning the fluff filters and air flow openings thoroughly

If the drying duration has become longer or the surface of the filters is visibly com-pacted with fluff, you should carry out the following cleaning procedure.

ĺ Pull the upper fluff filter forwards to remove it.

ĺ Turn the yellow dial on the lower fluff filter in the direction of the arrow (until you hear it click).

ĺ Hold the dial and pull the fluff filter forwards to remove it.

ĺ Use a vacuum cleaner with a long crevice nozzle attached to remove any visible fluff from the upper air flow openings.

ĺ Flush the fluff filters through with warm running water.

ĺ Shake the fluff filters thoroughly and then dry them carefully.

ɔ Ensure the filters are dry before replac-ing them. Wet filters could cause opera-tional faults.

ĺ Refit all of the fluff filters and close the door.

CLE

AN

ING

AN

D C

AR

E

PR

OB

LEM

SO

LVIN

G G

UID

E

Programme chart

PR

OG

RA

MM

E C

HA

RT

Gar

men

t ca

re la

bel

sym

bo

lsD

ryin

g

Nor

mal

/hig

her t

empe

ratu

re

R

educ

ed te

mpe

ratu

re: s

elec

t Gen

tle

tum

ble

(for d

elic

ate

fabr

ics)

.

D

o no

t tum

ble

dry

Iro

ning

Ve

ry h

ot

H

ot

W

arm

D

o no

t iro

n

Tip

s o

n d

ryin

g –A

lway

s ob

serv

e th

e m

axim

um re

com

men

ded

load

s gi

ven

in th

e "P

rogr

amm

e ch

art"

.

ɔ

Ove

rload

ing

can

caus

e un

nece

ssar

y w

ear a

nd te

ar o

f the

laun

dry,

giv

e a

dis-

appo

intin

g dr

ying

resu

lt an

d ca

use

mor

e cr

easi

ng.

–D

o no

t loa

d th

e dr

um w

ith it

ems

that

are

stil

l soa

king

wet

. Mak

e su

re y

our l

aund

ry is

spu

n at

the

max

imum

spi

n sp

eed

befo

re

dryi

ng.

–M

inim

um ir

on fa

bric

tend

s to

cre

ase

mor

e, th

e la

rger

the

load

. Th

is is

par

ticul

arly

the

case

for g

arm

ents

mad

e fro

m v

ery

fine

wea

ve fa

bric

, suc

h as

shi

rts

or b

lous

es.

Some of the messages in the display are more than one line long. Touch the or sensor to read them in full.

Problem/Fault message Possible cause and remedy

000 lights up after the tumble dryer is switched on and a pro-gramme cannot be selected.

Access via a code has been activated.You must enter the correct code to use the tumble dryer. See "Settings menu - PIN Code" in the operating instruc-tions.

The programme is can-celled and the following lights up: Empty container. See

The condensed water container is full or there is a kink in the drain hose. ĺ Empty the condensed water container. ĺ Check the drain hose.

To switch off the message: ĺ Open and close the door while the dryer is switched on.

Fill condensate container This is to remind you that water is taken from the condensed water container when the Steam care programme is being used. The condensed water container must be filled with water to at least the –min– marker. ĺ Confirm with OK.

Open & close door After selecting the Steam care programme, you are alerted to load laundry. ĺ Load the laundry in the drum.

At the end of the pro-gramme:

Clean the plinth filter. See

There is a build-up of fluff in the airways. See "Cleaning and care" in the operating instructions. ĺ Clean the fluff filters. ĺ Clean the plinth filter.

To switch off the message: ĺ Confirm with OK.

Programme cancella-tion:

Clean the plinth filter. See

There is a blockage due to fluff. See "Cleaning and care" in the operating instructions. ĺ Clean the fluff filters. ĺ Clean the plinth filter. ĺ Clean the area underneath the plinth filter. ĺ Clean the heat exchanger.

To switch off the message: ĺ Switch the dryer off and then on again.

Finish/Cooling down The programme has finished but the laundry has not yet cooled down. ĺ Either remove the laundry and spread it out to cool down or leave it in the tumble dryer to cool down during the cooling phase.

Problem/Fault message Possible cause and remedy

The display is in a dif-ferent language.

A different language has been selected in "Settings - Lan-guage ". ĺ Set the language you want. The flag symbol serves as a guide.

The display remains dark and the Start/Stop sensor does not light up or flash.

There is no power to the tumble dryer. ĺ Check whether the mains plug is plugged in and switched on.

ĺ Check whether the circuit breaker has tripped.The tumble dryer has switched off automatically to save energy. ĺ Turn the programme selector to switch the tumble dryer back on again.

The laundry is not suffi-ciently dry.

The load consisted of different types of fabric. ĺ Finish drying using the Warm air timed drying programme. ĺ Select a more suitable programme next time.

Tip: You can alter the residual moisture level for some pro-grammes. See "Settings menu - Drying levels" in the operat-ing instructions.

Items made of synthetic fibres are charged with static electricity after drying.

Synthetic fibres tend to attract static charge.Static charge can be reduced by adding a fabric softener to the final rinse in the washing programme.

There is a build-up of fluff.

Fluff is principally the result of friction when garments are being worn and to some extent when they are being washed. Machine drying hardly causes any fluff to form.Fluff is collected by the fluff filters and the plinth filter and can be removed easily.See "Cleaning and care".

There are humming noises.

This is not a fault. The compressor (heat pump) is operating.No action is required. These noises are quite normal and do not indicate a fault.

Pro

gram

me

Lo

ad

(wei

ght o

f dry

la

undr

y)

Item

s

Extra dry

Normal plus

Normal

Slightly dry

Hand iron

Hand iron

Machine iron

Extra

s

Co

tto

ns

9 kg

Cot

ton

item

s su

ch a

s th

ose

desc

ribed

und

er C

otto

ns N

orm

al

with

nor

mal

resi

dual

moi

stur

e.X

Co

tto

ns9

kgTo

wel

ling,

jers

eyw

ear,

T-sh

irts,

und

erw

ear,

baby

clo

thes

, wor

k-w

ear,

cove

rs, j

acke

ts, b

athr

obes

, and

flan

nele

tte b

ed li

nen.

Do

not u

se E

xtra

dry

for j

erse

y fa

bric

s (e

.g. T

-shi

rts,

und

erw

ear,

baby

clo

thes

), as

they

hav

e a

tend

ency

to s

hrin

k.

XX

XX

XX

X

, ,

,

Min

imum

iro

n4

kgW

orkw

ear,

over

alls

, pul

love

rs, d

ress

es, t

rous

ers,

legg

ings

and

ta

ble

linen

.–

XX

XX

X–

,

, ,

Del

icat

es2.

5 kg

Shi

rts,

blo

uses

, lin

gerie

, app

liqué

d ga

rmen

ts.

–X

XX

XX

–

, ,

Wo

olle

ns h

and

-ca

re2

kgP

ullo

vers

, car

diga

ns, s

ocks

, sto

ckin

gs.

––

––

––

–

Shi

rts

2 kg

Shi

rts

and

blou

ses.

–X

XX

XX

–

, ,

,

Mo

bile

Co

ntro

l Th

e M

iele

@m

obile

App

is u

sed

for s

elec

ting

prog

ram

mes

and

ope

ratin

g th

e m

achi

ne.

Ste

am c

are

1 kg

Min

imum

iron

item

s m

ade

of c

otto

n, s

ynth

etic

or m

ixed

fibr

e, e

.g.

trous

ers,

jack

ets,

shi

rts.

––

X–

X–

–

,

Bed

line

n4

kgB

ed li

nen,

pillo

w c

ases

.X

XX

XX

XX

,

Pro

ofin

g2.

5 kg

Mic

rofib

re fa

bric

, ski

wea

r, ou

terw

ear,

fine

clos

e w

eave

cot

ton

garm

ents

(pop

lin),

tabl

eclo

ths.

Fire

haz

ard

! Do

no

t us

e p

roo

fing

ag

ents

co

ntai

ning

par

af-

fin.

––

X–

––

–

,

Pre

-iro

ning

1 kg

Min

imum

iron

item

s m

ade

of c

otto

n, s

ynth

etic

or m

ixed

fibr

e, e

.g.

trous

ers,

jack

ets,

shi

rts.

––

X–

X–

–

, ,

Den

im3

kgJe

ans,

jack

ets,

ski

rts,

shi

rts.

–X

XX

XX

–

, ,

, W

arm

air

8 kg

Thic

k an

d m

ulti-

laye

red

jack

ets,

pillo

ws,

sle

epin

g ba

gs, b

lank

ets.

––

––

––

–

, ,

Out

erw

ear

2.5

kgO

uter

wea

r whi

ch is

sui

tabl

e fo

r dry

ing

in a

tum

ble

drye

r.–

–X

–X

––

,

, E

xpre

ss4

kgG

arm

ents

sui

tabl

e fo

r the

Cot

tons

pro

gram

me.

XX

XX

XX

X

, S

po

rtsw

ear

3 kg

Spo

rtsw

ear w

hich

is s

uita

ble

for d

ryin

g in

a tu

mbl

e dr

yer.

–X

XX

XX

–

, A

uto

mat

ic p

lus

5 kg

Mix

ed lo

ads

of g

arm

ents

sui

tabl

e fo

r the

Cot

tons

and

Min

imum

iro

n pr

ogra

mm

es.

–X

XX

XX

–

,

Pill

ow

s–

Pillo

ws

(2 s

mal

l 40 

x 80

or 1

larg

e 80

 x 8

0).

––

X–

––

–

, C

oo

l air

8 kg

Any

gar

men

ts w

hich

nee

d to

be

aera

ted.

––

––

––

–

, B

aske

t p

ro-

gra

mm

e3.

5 kg

ba

sket

load

Bag

s, s

hoes

, sof

t toy

s, b

eani

es, s

carv

es, g

love

s, s

equi

ned

tops

.O

nly

to b

e us

ed w

ith d

ryin

g b

aske

t (o

ptio

nal a

cces

sory

).–

––

––

––

Silk

s ha

ndca

re1

kgB

lous

es, s

hirt

s.–

––

––

––

,

=

Fre

shen

up;

=

Gen

tle tu

mbl

e;

= A

nti-c

reas

e;

= B

uzze

rX

= Ye

s, –

= N

o

Plinth filterClean the plinth filter when Clean the plinth filter. See light ups.

To delete the message: confirm with OK. ĺ Press the round,

indented area on the heat exchanger access panel to open it. The panel will spring open.

ĺ Pull the plinth filter out by the handle.

Removing the plinth filter will cause the right-hand guide pin in the dryer to come out. This pin ensures that the heat exchanger access panel can only be closed if the plinth filter is inserted the right way round.

ĺ Pull the handle out of the plinth filter.

ĺ Clean the filter thoroughly under running water.

ĺ Squeeze the water out of the plinth filter thoroughly.

ɔ The plinth filter must not be replaced dripping wet.

ĺ Use a damp cloth to remove any fluff from the access panel.

Checking the heat exchanger unit

ɔ Danger of injury! Do not touch the cooling fins. You could cut yourself.

ĺ Carefully vacuum up any visible fluff or dirt.

Refitting the plinth filter ĺ Fit the filter back

on the handle.

ĺ Insert the handle with the plinth filter attached over the two guide pins.

The word Miele on the handle must be the correct way up.

ĺ Close the heat exchanger access panel.