Upload
others
View
0
Download
0
Embed Size (px)
Citation preview
JOLJN LAB
BATÀ build guide v1.0
∞ Hi fellow! Just a quick intro before starting, Materials to have near you: 1. Soldering Iron - better with temperature control 2. Solder wire 3. A pair of tweezers 4. Multimeter 5. Cutter 6. Solder sucker / wick (optional) 7. Silicone soldering mat (optional) 8. Helping hands (optional) 9. Flux (optional) If you want to refresh yourself a bit about soldering stuff you can watch this video by GreatScott! A useful tool that can help you find the components on the boards is the interactive BOM linked here:
tinyurl.com/bata-bom Download it and open the .html file with a browser. You can use it to check where a component is located on the board. It works also offline.
now let’s begin!
resistors: They are placed in vertical position. The body of the resistor goes on top of the white circle marked on the PCB. If two resistors are placed mirrored one in front of the other and both their legs don’t fit into the hole don’t worry: cut the bent leg of one of the two resistors and solder it from the top.
tip: they don’t have a polarity; this precaution is due to avoid them touching while soldered. 2 R19, R20 33r 3 R7, R8, R9 100r 1 R18 649r 8 R2, R5, R6, R11, R14, R15, R17, R22 1k 8 R1, R3, R4, R10, R12, R13, R16, R21 2.2k 8 R23, R24, R25, R26, R27, R28, R29, R30 100k
film capacitors: Snap them in. Don’t mind their polarity. The value is written on top of the component.
8 C1, C2, C3, C4, C5, C8, C9, C10 100n 2 C6, C7 220n 1 C12 470n 1 C11 680n
vactrols: Match the short leg of the vactrol with the squared solder pad on the PCB. Look at the picture if you have any doubts.
tip: it’s easier to bend at 90° degree all the four legs before trying to fit the vactrol in place. 8 U1, U2, U3, U4, U5, U6, U7, U8 VTL5C1
ok, flip the board. we are almost done
jack sockets: Wait to solder them: just place all of them in the right place and move to the next step.
24 J1, J2, J3, J4, J5, J6, J7, J8, J9, J10, J11, J12, J13, J14, J15, J16, J17, J18, J19, J20, J21, J22, J23, J24 PJ398SM
LEDs: Short leg goes into the square pin. Don’t solder them yet
2 D1, D4 Green_3mm 2 D7, D8 Yellow_3mm 2 D3, D5 Orange_3mm 2 D2, D6 Red_3mm
At last put the panel on - check its direction - tighten the nuts and then solder all the jacks and LEDs -the closer to the panel, the more they will be evident on the panel’s hollow line. tip: we are soldering them now to ensure that all the jack sockets and LEDs are aligned with the panel
check if everything is in place
done! enjoy your new
BATÀ
find us: web ⇒ www.jolinlab.com
e-mail ⇒ [email protected] Instagram ⇒ @jolinlab
They are placed in vertical position.The body of the resistor goes on top of the white circle marked on the PCB.If two resistors are placed mirrored one in front of the other and both their legs don’t fit into the hole don’t worry: cut the bent leg of one of the two resistors and solder it from the top.tip: they don’t have a polarity; this precaution is due to avoid them touching while soldered.Snap them in. Don’t mind their polarity.The value is written on top of the component.Match the short leg of the vactrol with the squared solder pad on the PCB.Look at the picture if you have any doubts.tip: it’s easier to bend at 90 degree all the four legs before trying to fit the vactrol in place.Wait to solder them: just place all of them in the right place and move to the next step.done! enjoy your new