Water Efficiency

SINK MIXER

CLEANING RECOMMENDATIONS

Tech Page Version 2

SPECIFICATIONSRecommended use Domestic, hotel and commercial

Colour availability Chrome

Pressure rating

Temperature rating Maximum continuous working temperature 80°

4 Stars Flow Rate 7.5 L/min.

6 Stars. Flow Rate 4.5L/min

Suitable Hot Water Units

Standards AS/NZS 3718

page 1 of 2

We recommend the use of soapy water or approved cleaners. This product should not be cleaned with abrasive materials. Damage caused by any improper treatment is not covered by the product warranty - refer to Warranty Conditions on the last page.

258220

129

157

53M

AX

38

Maximim continuous operating pressure 1000 kPa.

Note: For best performance and longer life werecommend 150-500 kPa.

Hot and cold water inlet pressure should be equal.

Disclaimer: Products in this specification manual must by regulation be installed by licensed and registeredtrade people. The manufacturer/distributor reserves the right to vary specifications or delete models fromtheir range without prior notification. Dimensions and set-outs listed are correct at time of publicationhowever the manufacturer/distributor takes no responsibility for printing errors. Dimensions are nominal measurements only.

Storage Tank: Yes

Continuous Flow: Yes

Gravity Feed: Not suitable

BASE MK2

SINK MIXER

Plumbers, please ensu re a copy of the installation instructions is left with the end user for futu re reference

INSTALLATION

NoteThe installation must comply with requirements AS/NZS 3500. Mixer must be installed by a licenced plumber.

ImportantYour mixer comes to you already factory assembled and tested. We do not recommend the dismantling of any internal part of the mixer. The mixers are factory tested and sealed so as to give the best performace.

1. Please flush out new pipe work prior to connecting the newmixer.

2. All mixers should be installed with isolating stop cocks (Arcobrand recommended).

3. This tap is suitable for high pressure applications where bothhot and cold water supply pressures are at 150kPa or above.

4. Place the washer into position.

5. Fit the tap body (10) into the sink hole making sure first that theflexible connectors (19,20) are firmly tightened into the base of thebody.

6. Do not use teflon tap on threads.

7. From underneath apply your washer (15) prior to positioning thehorse shoe plate (16).

8. Lock the mixer onto the sink or benchtop by tightening the locknut s(18).

Servicing - Replacement of Cartridge1. Remove cap (3) and unscrew the grub screw (2) using allenkey.

2. Lift off handle and remove the cartridge dome (4), unscrewbrass locking nut (5) and lift out cartridge (6).

3. Replace the cartridge (6), replace the brass locking nut (5),cartridge dome (4) and replace handle (1). Tighten grub screw (3)and push in indicator cap (2).

2

3

103370003RECE Sink Mixer

103370003RECE

2Theory External Area[cm ]

1:4Scale

mmDrawing Unit

Theory Area[cm ]

Theory Weight [g]

EditionASMMaterial

Item Code

Description

MAIN PLAN LIMITED

Page 1;Total Pages 1

Authorized

Verify

Proofread

Designer

2

DateDesignRevised ContentMarking

Drawing Angle

Useful Measurement

Key Measurement

Measurement Tolerance Value (Not Marked) Angle Tolerance Value (Not Marked)

Basic Measurement 0＜a≤6 6＜a≤30 30＜a≤120 120＜a≤400±0.5 ~

Tolerance Value ±0.1 ±0.2 ±0.3 ±0.5

4

3

2

1

A B C D

DCBA

1

5

4

6

10

9

8

7

12

13

14

15

16

17

1

2

3

4

5

6

7

8

9

10

11

12

13

14

202020330226 ZINC 1

205010641601 SS304 1

202030380701 ABS 1

206023310726 ABS 1

204011099901 ASM 1

205021350102 H59 1

206091220126 H59 1

1

EPDM 2207041830601

1203122740126

POM 2207041820701

H59 1206061410126

NBR 1208001600601

207010730601 NBR 1

207020270505 Q235 1

205030121602 SS304 1

205021240102 H59 1

206012059901 ASM

1203100939901 ASM

16

17

18

19

20

1

206091210102-DR

H59+H62

Handle

Set screw

Plug

Cap

15

Neoperl aerator

O ring D40*D3.55

Rubber ring

Base

Cartridge

bushing

V Ring

Spout

Bonnet

Bonnet

206012049901 Flexible Hose (Single Groove Blue)

Flexible Hose (Single Groove Red)

Body DR

Series QuantityMaterialDescriptionComponent Code

LLQ 2013.3.15

LLQ 2013.3.15

TF 2013.3.15

JGJ 2013.3.15

ASM 1

Screw Stud

Fixing Plate

Washer

18

19

1120

Exploded View

Item Description Product Code

1-3 Sink Mixer Handle Complete 9502420

4 Cartridge Dome

5 Cartridge Lock Nut

6 Cartridge 9502422

7-13 Mixer Body

14-17 Sink Mixer Fixing Kit 9502427

18 Flexible Hose (Hot) 9502424

19 Flexible Hose (Cold) 9502425

20 Aerator Complete 9502423

page 2 of 2

BASE MK2

9.

10. Check for leaks.

Connect the flexible hoses to the hot and cold isolating stops, hand tighten plus half a turn of the nut to provide a watertight joint. Ensure that hoses are not under tension, twisted or kinked and if bent have a minimum radius of 30mm.