Upload
lamdat
View
216
Download
0
Embed Size (px)
Citation preview
1
2.
3.
4.
5.
6.
7.
1.
2.
3.
4.a) The Tenderer shall furnish copies of :
i) IT Registration Certificate with No.
ii) Sales Tax Registration Certificate with No.
iii) Service Tax Registration Certificate with No.
iv) Electrical Contractor's License with No.
v) Electrical Supervisor’s License with No.
5.
a)
b)
c)
d)
e)
1.
2.
Part 'B' of the tenders will be opened for those only who fulfils the qualifying criteria given in the tender document.
The unopened part 'B' along with Earnest Money deposit for those not fulfilling qualifying criteria will be
returned.Alternation/change in tender documents is to be authenticated.
Clarifications, if any, required on drawings, schedules, specifications, etc. can be obtained from our Consultant
M/s.Alinda 33,Santoshpur Main Road,Kolkata 700 075 Phone No -033-2425 0569,94337 98849
The Tenderer should also submit the following documents along with the Tender.
List of technical persons available on hand, years of their association with the firm & proposed to be engaged for the
subject work, if selected (marked Annexure-IX) ;
The bank will not be bound to accept the lowest tender and reserves the right to accept or reject any or all tenders
without assgming any reason whatsoever.
marked Annexure - VI
marked Annexure - VII
marked Annexure - VIII
List of works in hand indicating description of work, contract value, approximate value of balance work yet to be
done and date of award (marked Annexure-XII)
Contractors will be required to arrange for their own storing. Dismantled materials are to be carted away from site at
their own cost and disposed of in conformity with Municipal regulations.
Tenderer who will quote the rate must have a local office at Kolkata. This is absolutely essential for day to day
supervision & coordination of the work at site.
All informations are to be fully authenticated & documented failing which the documents submitted will not be accepted.
GENERAL TERMS & CONDITIONS
The tenderer are to visit the site and acquaint themselves with site conditions before quoting rates.
Bank of Baroda
Bank of Baroda, West Bengal, Sikkim & A & N Island invites sealed tenders in two bid system for the proposed
Civil,interior & electrical work of Jalpaiguri, Kadamtala Main Road,1st Floor,Ukilpara Jalpaiguri Dt Jalpaiguri Pin-
735101 The work is to be completed within 21 days.
List of important plant & machinery available on hand (own) and proposed to be inducted (own & hired to be given
separately) for carpentry & electrical work (marked Annexure-X)
List of works completed in the last (three) financial years under Bank / Govt., Semi - Govt,Govt. undertaking /
Corporate Sectors giving description of work, organisation for whom executed, approximate value of contract at the
time of award, date of award and date of scheduled completion of work, date of actual completion and final value
of contract should also be given (marked Annexure-XI)
marked Annexure - V
(Government of India Undertaking)
NOTICE INVITING TENDER
Interested agencies having experience in work of similar nature & magnitude and fulfilling the eligibility criteria given
below may download detailed tender document from Bank's Website http:bankofbaroda.com/tenders.asp
marked Annexure - IV
The tenderer should have completed in last three Financial years (i.e. current year & two previous financial year) in
Bank, Govt. or Govt. undertaking and Financial Institutions, Corporate Sectors, etc. minimum 3 (three) similar
composite work (Interior Furnishing & Electrical) costing not less than Rs. 15.00 lacs in single contract. (Work order &
completion Report in support must be submitted & marked as Annexure-I)
The total contract amount received by the Tenderer during the last 3 financial years should be minimum as 40.00 lacs
per year in contract work. In support of this the Tenderer should submit audited sheet duly Certified by the Chartered
Accountant & marked Annexure-II.
The Tenderer should produce Solvency Certificate from any Nationalised / Scheduled Bank for an amount of 200% of
the advertised Tender value marked Annexure-III.
Part 'A' envelope (Technical Bid) shall contain : Earnest Money, the documents for satisfying eligibility criteria & the
technical & financial stipulation, if any, of the tenderer & Part 'B' shall contain : financial bid along with a copy of the
tender document, duly signed in all pages both shall be separately sealed & submitted in another sealed envelope
to the Deputy General Manager, Bank of Baroda, West Bengal, Sikkim & A & N Island, BARODA TOWER, Plot No. 38/2,
Block GN, Sector-V, Salt Lake City, Kolkata : 700 091, before 2.30 P.M. on 06.02.2012 along with Earnest money
amounting to Rs. 10,000/- by Bank Draft / Pay order in favour of Bank of Baroda shall be submitted in Part 'A'.
MINIMUM ELIGIBILITY CRITERIA (Shall be submitted with Part A of the Offer)
Part 'A' will be opened at 3.30 p.m. on 06.02.2012.
1
3.
4.
5.
6.
7
8.
9.
10.
11.
The quoted rates, are to include cost of all materials, labour and or any other material, all statutory taxes, transport,
handling delivery at site and installation, complete in all respect, as per drawing, directions or instructions of
Employer/Consultant. The quoted rates are also to include dismantling of partitions, counters, old electrical wirings
etc. and stacking serviceable materials and disposal of debris, etc.
Prior approval of the Employer/ Consultant shall be obtained for colour and thickness of laminates to be used in the
work.
The arrangement for “ Wire Management " is to have prior approval of the Client.
The quoted rates shall remain firm during the entire currency of contract. No price variation for any causes
whatsoever, shall be entertained.
The time of completion shall be 21 days from the date of placement of order.
The offer shall remain valid for acceptance for a period of 30 days from the date of submission of offer.
The bank will not be bound to accept the lowest tender and reserves the right to accept or reject any or all tenders
without assgming any reason whatsoever.
Payments will be made once on completion by the Employer within 15 days after certification of bill by the
Consultant 10% of the total payable amount is to be retained as retention money and will become due for release
after expiry of six months from the date of completion of the installation & subject to satisfactory maintenance of the
executed work.
Tenders addressed to Deputy General Manager, Bank of Baroda, West Bengal & Sikkim Region and submitted at his
office at BARODA TOWER, Plot No. 38/2, Block GN, Sector-V, Salt lake City, Kolkata : 700 091, before 2.30 P.M. on
06.02.2012, accompanied by Earnest Money amounting to Rs.10,000/- by Bank draft payable to Bank of Baroda and
other documents as mentioned in NIT. Part 'A' of the tenders will be opened at 3.30 P.M. on the same date.Part 'B' will
be opened immediately after opening of Part 'A'.
2
SPECIFICATION OF MATERIALS FOR INTERIOR WORK
Sl.No. Description
1. Laminate
2. Ply & Block Board
3. Glass
4. False Ceiling & Accessories
5. Veneer
6.Textured Wall Paint
7. Glue
8. Locks
9. Aluminium Hardware Fittings
10. Brass Hardware
11.
Floor Spring
12. Screws
13. Casters
14. Sliding Drawers / Channels
15. Furnishing Fabric
16. Leather Foam
17. PVC Flooring
18. Carpet
Earl Behari / Efficient Gadjets
Make (s)
Metako / Allen / Crown with ISI Mark
India Gypsum Ltd.
Marino / Greenlam / Century / Archid
Green / Century / Archid / Austin
Modi / Indo Ashahi / Float Glass India Ltd.
Glamour or Favourite (Balla Industries)
Woven type "Harmony" range from "Vimal"
or equivalent
Bhor Industries or equivalent
Armstrong / Krishna / Premier
Durian / Century / Archid
ICI, Jenson & Nicholson / Asian paint /
Berger
Efficient Gadjets
Evrite Agencies Pvt. Ltd. / Nita Floor Spring
Nettle Fold
ICI, Spectrum, Heritage
Godrej / Secur / Yale
Brass Arts / Vijoy
3
SPECIFICATIONS OF MATERIALS FOR ELECTRICAL WORK
Sl.No. Description
1. Switch fuse / fuse switch units (HRC) (32A TPN & above)
2. Timer (TSQ 100)
3. Voltmeter & Ammeter
4. Voltmeter & Ammeter selector switches
5. Phase indicating lamp
6.
7. Capacitor
8. HRC fuses
9. Power Cable : XLPE
10.
11. HRC fuse base & carriers.
12. PVC terminals
13. 1.1 KV grade PVC insulated armoured aluminium cable (ISI marked)
14. 1.1KV 660V grade PVC insulated & sheathed / insulated copper wire &
flexible cords (ISI marked).
15. Moulded case circuit breaker
16. RCCB / ELCB
17. Switch fuse with rewirable fuses. (6A & 32A TPN)
18. Isolator
19. Changeover switch (on load type)
20. MCB distribution board
21. Distribution fuse board with rewireable fuses
22. Miniature circuit breaker / MCB type isolator
23. Contractors
24. Auxiliary contractor
25. 1/16 Amp Piano key type switch / flushed type plug socket
26. 6/16 Amp modular switch / socket, module plate & mounting M.S. /
PVC box.
27. 300W, 2 module electronic regulator
Make (s)
HAVELL’S / STANDARD
Vaishno / SIEMENS / ROSS controls
L & T
GE power / SIEMENS / L&T / Schneider
A. E. / IMP
ELMEX / ESSEN
SIEMENS / L & T/BCH
SIEMENS / L & T
KAYCEE / L & T
UNIVERSAL / GLOSTER / NATIONAL / NICCO
/
L & T / SCHNEIDER/LEGRAND
CPL (Genius) / ANCHOR (Roma) / CRABTREE
/
MK
ANCHOR (Roma) / CRABTREE / MK
ANCHOR / PRECISION / SSK & RIDER
HAVELL’S / STANDARD
NATIONAL/FINOLEX/ HAVELLS
LEGRAND / SIEMENS
HAVELL’S / BPC / BOSMA
KENBAR / HAVELLL’S / ELCON / HPL /
CONTROL & SWITCHGEAR.
LEGRAND/ SIEMENS
A E / KAPPA SEGC & CONTROLS / CONTROL
CROMPTON/SIEMENS
TATA LEVERT/NEUMERIC/ KIRLOSKAR
GLOSTER/INCAB/POLYCAB/CINOLEX
GE power / SIEMENS / L & T / SCHNEIDER
SWITCHGEAR
GE Power/SIEMENS/L&T/SCHNEIDEV
LEGRAND/ SIEMENS / L&T
4
Sl.No. Description
28. Ceiling rose
29. Holder
31. Luminous indicating type buzzer with cancellation push.
32. Alarm bell.
33. G.I. pipe
34. Steel conduits (conforming to IS in all respects)
35. Black enamelled
36. Galvanised
37. Non-metallic PVC conduit pipe
38. Compression type brass gland
39. Cable termination socket
40. Light fitting & lamps
41. Decorative/Ornamental /Chandelier / Light Fittings
42. Ceiling Fan
43. Exhaust fan
44. Industrial type socket & top
45. Telephone wire
46. Telephone Socket
47. Network Cable
48. Contractors
49. STARTERS
Make (s)
KAY / EPP / ANCHOR / JJ
Good local make with minimum wall
thickness of 3 mm. for 19 / 20 mm. and 25mm
sizes & 2.5 mm. for 12mm. sizes
BEC / SUPREME / AKG
BEC / SUPREME / AKG
BST / BANSAL
KHERAJ / GETCO
KAY / EPP / ANCHOR / JJ
NATIONAL / HOMA / EQUIVALENT
DOWELL'S
WIPRO or equivalent
DOWELLS / JOHNSON / COMET
PLAZA / KALINGA/ PRECISION/AKG or
equivalent
FINOLEX or equivalent
L & T / SIEMENS
CROMPTON / POLAR / KHAITAN
NORTH WEST / CABTREE
CROMPTON / POLAR / KHAITAN
HAVELL’S / CROMPTON / LEGRAND
FINOLEX / RRK/NATIONAL
CRABTREE/MK
CROMPTON / POLAR / KHAITAN / EPC
5
SL. UNIT QNTY. RATE AMOUNT
NO. Rs. P. Rs. P.
1.00 Supplying and laying true to line and level vitrified tiles of approved brand
size not less than 600mm x 600mm x 10mm thick in floor , skirting etc.
using polymerised adhesive (as per manual of the applicator ) over
existing floor finish , after preparing the same by means of cleaning ,
scrapping as necessary for existing floor, joints grouted with admixture of
white cement and colouring pigment to match with colour of tiles
complete finishing in all respect as per instruction sqm. 40
2.00 Striping of worn out plaster, renewing with new plaster work (1:6)
of sand cement morter of 15mm/20mm ( making level as per site condition)
mixing with water proofing agent ( Sika Latex or similar make) mixing
as per applicator's manual matching with old plastered surface and
complete in all respect sqm. 40
4.00 Removal of rubbish, earth etc. from the working site
and disposal of the same, beyond the compound, in
conformity with the Municipal/Corporation Rules for
such disposal, loading into truck and cleaning the site
in all respect as per direction of Engineer-In-Charge Cum. 10
5.00 Removing old tiles and fitting and fixing 1st quality ceramic tiles of
approved size, shade and brand in wall and floor including borders
to match with existing work where applicable, set in sand cement
mortar (4:1) including backing concrete(1:2:4)and 4nos.
key stone (10mm) fixed with areldite at the back
of each tile and finishing the joints with white cement
mix with colouring oxide (if requested) to match the
colour of tile
i) FLOOR sqm. 45
ii) DADO (TOILET) sqm. 20
ii) DADO (KITCHEN) sqm. 6
6.00 BLACK STONE PANTRY COUNTER (2'-0" WIDE)
Providing and laying platform of 3/4" thk. & 2' width (clear) and at
2'-8" height (top) above fl. of approved Kota stone with champhered and
machine polished edge. It shall be supported on wall on 11/2" thk
horizontal kota stone. Rate shall include the profile cutting and
fixing of below counter wash basin/kitchen sink & polishing the
exposed edges. A 2" kota stone shall be provided
below the champhered edge. sqm. 7.6
7.00 Stainless steel sink
P/F/F Stainles Steel sink with single bowl of Nirali make, integrated
waste size-over all 600 x 450 mm. with a pair of C.I. bracket, fitted with
15mm dia. Brass C.P. Pillar tap & 32 mm. dia white pvc waste pipe No. 1
with brass coupling etc. complete.
9.00 Spot application for insecticides using aqua base sprey for pest ( for
bugs, cockroaches, silverfish, termites etc ) to walls and ceiling etc.
INTERIOR WORKS OF OF BANK OF BARODA
JALPAIGURI BRANCH
PRICED BILL OF QUANTITIES FOR CIVIL WORKS
DESCRIPTION OF ITEMS
Civil works of Jalpaiguri Branch, BOB. Consultant : ALINDA
SL. UNIT QNTY. RATE AMOUNT
NO. Rs. P. Rs. P.
DESCRIPTION OF ITEMS
with chemical emulsion by admixing chloropyrofos emulsifiable
concentrates (1% concentration ) with water by weight including
spraying the emulsified chemical @0.5 ltr. Per sqm. on wall surfaces ,
ceiling , electrical lines including drilling holes in places where source of
termite is detected squirting chemical solution into the holes and sealing
with cement grout , finish in all respect. sqm. 650
11.00 Rendaring the surface of walls and ceiling with plaster of paris
( thickness not less than 1.5 mm) matching with old pop surface. sqm. 45
12.00 Painting of doors and windows with synthetic enamel paint(02 coats) of
approved make and shade after applying 02 coats of oil bound primer
of approved make including smoothening of surfaces with putty as
necessary , complete in all respect. sqm. 190
13.00 Applying two or more coats of Acrylic Emulsion paint of
approved shade and brand, over a coat of primer to give
a even shade on wall / ceiling surface including preparation
of surface complete with labour and material. sqm. 425
14.00 Supplying fitting and fixing of 2100 high PVC door
of approved make and thickness along with PVC
door frame , clamp, hinges, bolts and
all other necessary fittings complete in all respect set 2
SANITARY & PLUMBING FITTINGS AND FIXTURES
Supplying fittings and fixing of following s&p fittings
and fixtures of Jaquar /Cera or similar make where
applicable as per approval of the authority
15.00 Swan-neck piller cock for sink no. 1
16.00 EPWC with cistern & fittings copmlete of approved make no. 2
17.00 350x550 wash basin with fittings copmlete of approved make no. 2
18.00 Chromium plated pillar cock of approved make no. 2
19.00 Chromium plated bib cock of approved make no. 2
20.00 Chromium plated Towel ring 150 dia no. 2
21.00 Chromium plated soap tray no. 2
22.00 Comprehensive sanitary and plumbing works for 02 nos. toilets
& 1 no. pantry along with supplying , fitting and fixing of
necessary waste pipes and plumbing pipe , loft tanks
lines of required dia , stop cocks of approved make,
complete as per direction of engineer in charge. L.S.
0.00
NOTE All debries are to be removed from site in conformity with local regulations. Rates to include this.
TOTAL COST FOR CIVIL AND SANITARY & PLUMBING WORKS
Civil works of Jalpaiguri Branch, BOB. Consultant : ALINDA
SL. UNIT QNTY. RATE AMOUNT
NO. Rs. P. Rs. P.
1.00 FALSE CEILING
Providing and fixing in position dropped ceilling in two levels
including vertical surfaces in between two level of ceiling surface
with 12.5mm thick tapered edge gypsum board conforming to
IS 2095 including providing and fixing of framework made of
special sections power pressed from MS Sheet and galvanised
in accordance with Zinc coating 600 as per IS 277 and costing
of angle cleats of size 25mm wide x 16mm thick with flanges
of 22 mm and 37 mm at 1200mm center to center one flange
fixed to the ceiling with dash fastner 12.5mm dia x 40mm long
6mm dia bolts to the angle hangers of 25x25x5 mm of required
length and other end of angle hanger being fixed with nut and
bolts to g.I Channels 45mm x 15 mm x 0.9 mm running at the
rate of 12 mm centre to centre to which the ceiling section
0.5mm thick botton wedge of 08mm with tapered flanges of
26mm each having clips of 10.5mm at 450mm center to centre
shall be fixed in a direction perpendicular to G.I. Channel with
connecting clips made out of 2.64 mm dia x 230mm long G.I.
Wire at every junction including fixing the gypsum board with
ceiling section and perimeter channel.
The perimeter of ceiling fixed to wall/partition with the help of
rawl plugs at 450mm center with 25mm long drive all screws
@ 230mm interval including jointing and fixing to a flush finish of
tapered and square edges of the gypsum board with
recommended filter, paper tapes, finisher and two coats of
primer suitable for gypsum board as per manufactures
specification and also include the cost of making openings for
light fittings grills, diffusers, cutouts made with frame of
perimeter channels of the Engineer-in-Charge but excluding the.
cost of painting.
Rates to include cost of making openings for ceiling mounted
electrical/air-conditioning accessories as per instructions.
(The work to be carried out through authorized applications of
M/s. India Gypsum Ltd.) sqm. 110
2.00 DOUBLE SKIN PARTLY GLAZED FULL HEIGHT PARTITION
Supplying and erecting Full Height Partly Glazed partitions
up to 8' 6" high) as per drawing and conforming to the
following specifications :
Basic Framework : Well seasoned Malayasian sal wood
sections, treated with two coats of wood preservations, 50mm
x 50 mm (minimum) at maximum 600 mm horizontal or
vertical spacing as per site conditions. Vertical Members shall
be suitably anchored and at ceiling level to ensure rigidly.
Exposed frame members in the glazed portions shall have
wider spacing (approx. 1800 mm clear) as per instructions.
Exposed members shall be finished with 1.0mm thick laminate
sheet of same or combination shades, 2 x 6 mm BWR
grade plywood facing including 4x4 mm grooves at locations
as per instruction.
Skin Membrane : (Opaque portion upto 900 mm from floor
level with 2 x 6 mm thick BWR grade plywood on each face
with 4x4mm grooves formed at the top layer as per drawings /
instructions.
Finishing : 1.0mm thick laminate sheet of same or
combination shades as per instructions.
Skirting : 100mm high x 12mm thick polished white or steam
beech wood skirting on both faces with NC lacquer in Matt finish.
Glazing : 6mm thick clear float glass fixed with continuous
White or Steam Beech wood glazing beads of approved shape
(finished 35x25mm) all around, polished & coated with NC
lacquer finish. The rate should also include cost of decorative
etching on one side of the glass.
Quoted rates shall include all necessary materials, accessories
and also allow provisions for electrical/telephone/computer
wiring conduits and switch boxes, etc (Materials of wiring sqm. 35
INTERIOR WORKS OF BANK OF BARODA
JALPAIGURI BRANCH
PRICED BILL OF QUANTITIES FOR INTERIOR & FURNISHING WORKS
DESCRIPTION OF ITEMS
Interior works of Jalpaiguri Branch,BOB Consultant : ALINDA
SL. UNIT QNTY. RATE AMOUNT
NO. Rs. P. Rs. P.
DESCRIPTION OF ITEMS
3.00 FULL HEIGHT SOLID PARTITION
Supplying and erecting full height opaque partitions (from 8'6"
10ft. High) as per drawing and conforming to the following
specifications:
Basic Framework : Well seasoned Malayasian sal wood
sections, treated with two coats of wood preservatives, 50mm
x 50mm (minimum) at maximum 600 mm horizontal or
vertical spacing as per site conditions. Vertical Members shall
be suitably anchored and at ceiling level to ensure rigidity.
Skin Membrane : 2x6 mm thick BWR grade plywood as per
drawings/instructions.
Finishing : 1.0mm thick laminate sheet of same or
combinations shades as per instructions.
Skirting : 100mm high x 12 mm thick polished white or steam
beech wood skirting on both faces with NC lacquer in Matt finish.
Other specs same as item no.2
Skirting : 100mm high x 12 mm thick polished white or steam
beech wood skirting on both faces with NC lacquer in Matt finish.
Other specs same as item no.2 sqm. 25
4.00 MAIN ENTRANCE DOOR
Providing & fixing in position Twin stile door made of 40 mm
thk well seasoned teak wood of top & bottom stiles, fixed
portion with 8 mm thk. Clear float glass & openable portion
with double shutter made of 12 mm thk clear float glass with
necessary hardware fixtures of approved make & design,
viz. double action ISI marked floor springs, on which the
shutters are pivoted at the top & bottom, brass flushbolt,
satin finish stainless steel decorative tubular handles on
both the faces, (Dorset or equivalent approx. 300 mm long)
complete as per direction. Rate should include etching of the
Bank's logo & emblem on the Glass in the size & design as
approved by the architect. Wooden surface should be
polished in approved shade N.C. Lacquer in matt satin finish.
a) Openable Shutter sqm. 2.5
5.00 SOLID FLUSH DOOR
Supplying and fixing in position overall 37mm thick solid core
hot pressed phenol formaldehyde bonded approved flush door
shutter finished with 1.0mm thick laminate sheet of approved
shade and quality on both sides of the door shutter including cost
of hardware fittings e.g. mortic locks, brass hinges, door handles
etc. of approved make
a) Average size of shutter (D2) : 0.75m x 2.1m nos. 4
b) Average size of shutter (D1) : 0.90m x 2.1m nos. 1
6.00 PARTLY GLAZED DOOR SHUTTER
, Providing, fixing & fitting in position Door shutters made of
specification similar to that of item (5) hinged on 3 nos.
brass hinges as required with the exception that the wooden
frame is of section 2" x 1.5". The cost of all fittings: handle
locks, aldrop handles door closer, night latch all of approved
make to be included. The glazed portion will be between
3'-0" to 6'-8" of 5mm thk. Glasspanes of approved quality.
Average size of shutter (D3) : 0.9m x 2.1m nos. 2
Average size of shutter (D4) : 0.75m x 2.1m nos. 2
7.00 WOODEN PANELLING ON WALL AND PILLARS
Wall Panelling / column encasing (upto 2700 mm high) works
as per drawing and conforming to the following specifications :
Basic frame work
Well seasoned Malayasian Sal Wood sections, treated with two
coats of wood preservatives, minimum 50x25mm, at suitable
horizontal / vertical spacing not exceeding 600 mm c/c.
Skin Membrane
2x4 mm thick BWR grade plywood with 4x4mm grooves formed
at top layer as per drawing/instructions.
Finishing
1mm thick laminate sheet of same or combination shades as per
instructions.
Skirting
100mm high x 12mm thick polished white or steam beech wood
skirting with NC lacquer finish.
Quoted rates shall include all necessary materials, accessories
and labour and also allow provisions for electrical/telephone/
computer wiring conduits and switch boxes etc. complete with
necessary jacking/thickening of panels to accommodate
Interior works of Jalpaiguri Branch,BOB Consultant : ALINDA
SL. UNIT QNTY. RATE AMOUNT
NO. Rs. P. Rs. P.
DESCRIPTION OF ITEMS
conduits/switch boxes. (Materials for wiring conduits and switch
boxes shall be separately paid for). sqm. 35
Interior works of Jalpaiguri Branch,BOB Consultant : ALINDA
SL. UNIT QNTY. RATE AMOUNT
NO. Rs. P. Rs. P.
DESCRIPTION OF ITEMS
8.00 Writing Ledge
P/F/Fcheque writing tables made of 1 no. 19mm plywood shelf 3' (w) x
1' (d) x 3'(h) which is finished with 1mm thick Laminate on all exposed
surface. The shelf is fixed with two intermediate 8mm thk glass
partition fixed with D brackets for keeping withdrawal/deposit forms.
The table top shall be of 12mm thick plain glass fixed with SS studs
on the shelf.
Item is to be completed in all respects as per direction of Architect no. 1
9.00 PLASTER OF PARIS CORNICE
Providing and fixing Plaster of Paris Conice (out of 65x65mm sections)
at junctions of false ceiling, walls and at other locations. RMT. 85
10.00 FULL HEIGHT FILING CABINET/ALMIRAHS
Full height Filing cabinet/Almirahs 1'-4" deep & upto false ceiling height
of 8'-6" made of 18mm BWP blockboard with intermediate shelves. The
back of the cabinet to be made of 6mm thk. BWP ply with a ply skirt-
ing/base of 100mm high. There will be three sets of shutters above 3'-6"
height below 3'-6" height & above 7ft. Height. There will be vertical divi-
ders of same block board at approx. 3ft. Apart on which the shutters are
hinged. All exposed surfaces are finished with 1.5mm thk. Decorative
laminet of approved make & shade. All exposed edges of the commercial
ply & the block board are to be finished with 1/4" thk. Rubber wood
lipping which are to be melamine polished as directed. Cost of all fitting
like brass hinges, Godrej locks, magnetic catches, powder coated "D"
type steel matt finish metal handles shall be inclusive. sqm. 18
11.00 Low height Filling cabinet 1'4" deep & upto height of 2'-8"
made of 18mm BWP blockboard with intermediate shelves
The back of the cabinet to be made of 6mm thk. BWP ply with a
BWP ply with a ply skirting /base of 100mm high.
There will be one horizontal division and vertical dividers of
same block board at approx. 3ft apart with sliding shutters.
All exposed surfaces & the shutters are finished with
1.0 mm thk decorative laminate of approved make & shade
Cost of all fittings like brass hinges, godrej locks, magnetic
hinges, godrej locks, magnetic catches, steel matt finish "D"
type handles shall be inclusive.
Skirting
100mm high x 12mm thick polished white or steam beech wood
skirting with NC lacquer finish. sqm. 5.5
12.00 WINDOW SCREEN
Providing, fitting in position 100mm vertical blinds made of
best quality PVC coated polyester fabric of approved make
& shade & to be tailored to the size of the window. sqm. 20
13.00 Display Panels
Providing & fixing in position frameless double acrlyic trans-
parent sheet 2600X1200 (w) mounted with mirror screws
/nuts on the wall along with all accessories complete for
display of bank's schemes/posters/notices inserted on it. nos. 1
14.00 PIN-UP NOTICE BOARD
Providing, fitting in position pin-up board made of soft
cork board finished with the fabric as approved, matching
with the colour scheme of the banking hall with a R.W.
moulding all around the edges.(1200x750) sqm. 1
NOTE All debries are to be removed from site in conformity with local regulations. Rates to include this.
TOTAL OF INTERIOR AND FURNISHING WORKS
Interior works of Jalpaiguri Branch,BOB Consultant : ALINDA
ELECTRICAL WORKS OF BOB , JALPAIGURI BRANCH
Item no. Description Unit Quantity Unit Rate Total
(Rs.) (Rs.)
A. CONCEALED WIRING (Supply and Installation)
(Including supply of materials, groove cutting in wall
and makig good damage to original finish)
A1) Point wiring for Light/Fan/Exhust through concealed
conduit. These include:
a) 2 nos. 1.5 Sq.mm PVC insulated (FRLS) stranded
copper wire 1100V grade. (Make- Polycab, Finolex
& Mescab)
b) 1 no. 1.5 Sq.mm PVC insulated (FRLS)stranded
copper wire 1100V grade for earthing.
c) 16 SWG G.I. Junction Box (100x100x62 mm) with 5
mm thick acrylic cover and fixing accessories.
d) 1.6mm(16 SWG) thick painted MS switch box
e) 6A, 240V Moduler switch to be mounted on
switchboard .(Make- MK,& ABB)
f) Required module number of mounting frame with
sheet cover
g) A two/three way circular box to be provided for each
light point in brick wall.
i) - Length upto 6 metre Nos. 90
Note :
i) Min 2 nos. PVC conduit of 20mm dia to be laid
between switchboard and junction box which is
vertically in the same line with the switch board, if
required.
ii) All junction boxes shall be mounted in the same
level in their respective room.
iii) Vertical position of junction box shall be fixed in the
same line with the switchboard.
Item no. Description Unit Quantity Unit Rate Total
(Rs.) (Rs.)
A2) 6A receptacle (RA Type) wiring from nearest
JB/Switch Board to independent 6A, 5 pin, 240V
receptacle by supplying & laying of 1100V grade 2-
1/Cx1.5 Sq.mm + 1-1/Cx1.5 Sq.mm for earthing
PVC insulated (FRLS) copper wire through PVC
concealed conduit in wall/floor with groove cutting
and making good damage to original finish including
supply of necessary sheet metal pull box/ circular
box with 5mm thick acrylic sheet cover(Make-
Polycab,Finolex, & Mescab)
Meter 190
A3) 16/6A (RB Type) receptacle wiring from Distribution
Board/nearest JB to independent 16/6A, 6 pin, 240V
receptacle by supplying & laying of 1100V grade 2-
1/Cx2.5 Sq.mm + 1-1/Cx1.5 Sq.mm for earthing
PVC insulated copper wire through PVC concealed
conduit in wall with groove cutting and making good
damage to original finish including supply of
necessary sheet metal pull box/ circular box with
5mm thick acrylic sheet cover (Make-
Polycab,Finolex, & Mescab)
Metre 90
A4) Circuit wiring from Distribution Board/nearest JB to
Switch Board/Work stations by supplying & laying of
1100V grade 2-1/Cx4 Sq.mm + 1-1/Cx2.5 Sq.mm
for earthing PVC insulated (FRLS) copper wire
through PVC concealed conduit in RCC slab/wall
with groove cutting and making good damage to
original finish including supply of necessary sheet
metal pull box/ circular box with 5mm thick acrylic
sheet cover (Make- Polycab,Finolex, & Mescab)
Metre 50
A5) Power unit for A.C wiring by supplying & laying of
1100V grade 2-1/Cx6 Sq.mm + 1-1/Cx2.5Sq.mm for
earthing PVC insulated (FRLS) copper wire through
prelaid PVC concealed conduit in wall with groove
cutting and making good damage to original finish
including supply of necessary sheet metal pull box/
circular box with 5mm thick acrylic sheet cover
(Make- Polycab,Finolex, & Mescab)
Meter 55
Item no. Description Unit Quantity Unit Rate Total
(Rs.) (Rs.)
A6) Sub Main wiring by supplying & laying of 1100V
grade 3-1/Cx10 Sq.mm + 2-1/Cx6 Sq.mm for
earthing PVC insulated (FRLS) copper wire through
prelaid PVC concealed conduit in wall with groove
cutting and making good damage to original finish
including supply of necessary sheet metal pull box/
circular box with 5mm thick acrylic sheet cover
(Make- Polycab,Finolex, & Mescab)
Meter 20
A7) Main wiring by supplying & laying of 1100V grade 4
core 25 Sq.mm AL /A cable+ 2 nos 8 SWG GI wire
for earthing through in wall with necessary
termination and clamping or groove cutting and
making good damage to original finish .(Make-
Laser, crystal & Hevell's)
Metre 20
B. DISTRIBUTION BOARDS
[As per Dwg. and Specification]
LIGHTING/ POWER TPN/SPN DISTRIBUTION
BOARD
Supply and Installation of sheet steel (1.2 mm thick)
enclosed, double door, wall mounted Distribution
Boards complete with necessary mounting, internal
wiring and conduiting .(Make- L&T , ABB &.
Hevell"s)
B1) a) Incomer with for (Lights and Raw power ) Nos 1
63A, 415V, 4P, RCCB (100mA) - 1 No.
b) Busbar
415V, 63A, 3 PH, 4W, 50 Hz, 10 KA busbar - 1 No.
c) Outgoing with
6A - 32A, SP MCB (C curve) - 18 Nos.
B2) a) Incomer with for (AC power) Nos 1
63A, 415V, 4P, RCCB - 1 No.
b) Busbar415V, 63A, 3 PH, 4W, 50 Hz, 10 KA busbar - 1 No.
c) Outgoing with
20A - 32A, SP MCB (C curve) - 12 Nos.
B3) a) Incomer with for (UPS power) Nos 1
63A, 240V, DP, MCB - 1 No.
b) Busbar
240V, 63A, 1 PH, 3W, 50 Hz, 10 KA busbar - 1 No.
c) Outgoing with
Item no. Description Unit Quantity Unit Rate Total
(Rs.) (Rs.)
10A - 32A, SP MCB (C curve) - 18 Nos.
C) RECEPTACLES
C1) Supply and Instalation of 16A 240V international
socket (Similer to MK make DW426WHI) with safety
shutter and 16A moduler type switch complete with
M.S. Box and mounting frame with cover
plate.(Make- MK,ABB& similer reputed make)
No. 16
C2) Supply and Instalation of 6A, 5 Pin, 240V
receptacle (RA Type) with safety shutter and One
6A moduler type switch for complete with M.S. Box
and mounting frame with cover plate (Make- MK,&
ABB)
No. 31
C3) Supply and Instalation of 3 no.(Three) 6A, 5 Pin,
240V receptacle (RA Type) with safety shutter and
controlling 6A moduler type switch to be mounted in
board complete with wiring by 1Cx1.5 sqmm PVC
insulated wire (Make- MK,& ABB,similer reputed
make)
No. 11
C4) Supply and Instalation of RJ 12 telephone socket
complete with M.S. Box and mounting frame with
cover plate.(Make- MK,& similer reputed make)
No. 11
C5) Supply and Instalation of RJ 45 computer socket
complete with M.S. Box and mounting frame with
cover plate.(Make- MK ,& ABB )
No. 11
D. CONDUIT
Supplying & laying of PVC conduit to be fixed in wall
/ floor after proper chasing. The wall/floor to be
finished as it was before, after embedding the
conduit. (Make- AKG , PICISION)
D1) i) The following sizes of conduits
a) 20 mm dia Metre 380
b) 25 mm dia Metre 55
D2) Supply and Installation of flexible PVC Conduit of
following sizes :
a) 20 mm dia Metre 25
b) 25 mm dia Metre 15
D3) Supply and installation of medium duty G.I.
Conduit/Pipe of following sizes including all
necessary accessories required for fixing the conduit
on brick wall.(Make- TATA, AKG or other similer
make)
Item no. Description Unit Quantity Unit Rate Total
(Rs.) (Rs.)
a) 25 mm dia conduit/pipe Metre 5
E) MISCELLENEOUS ITEMS
E1) Supply and drawing of DIA 0.5 mm, three pair
Telephone Cable with necessary conection as
required (Make- Polycab,Finolex, or other similer
make)
Meter 50
E2) Supply and fixing TPN 125A SFU with sheet steel
encloser in iron fream with necessary connection
as required (Make- L&T , ABB &.Hevell's)
No 1
E3) Supply and fixing one set of LED/NEON indicator
engage light (yellow, red and green) at out side of
Maneger room with necessary mounting and
connection as required ( Make- Anchor or
other similer make)
No 1
E4) Supply and fixing flush-type power unit complete of
DP MCB,SP starter ( 7A-11.50A), socket & plug with
indicating light with necessary mounting and
connection as required for 1.5 Ton A.C Unit ( Make-
Northwest or other similer make)
No 9
E5) Supply and fixing flush-type power unit complete of
DP MCB,SP starter ( 4.75A-7.50A), socket & plug
with indicating light with necessary mounting and
connection as required for 1 Ton A.C Unit ( Make-
Northwest or other similer make)
No 2
E6) Supply and fixing of 300 mm sweep wall fan with all
necessary mounting and connection as required
(Make- USHA , ORIENT,& similer reputed make)
No 20
E7) Supply and fixing of 300 mm dia exhust fan with
louver and all necessary mounting and connection
as required (Make- USHA , ORIENT,& similer
reputed make)
No 3
E8) Supply and fixing of 1200 mm sweep ceiling fan
with louver and all necessary mounting and
connection as required (Make- USHA , ORIENT, &
CG)
No 2
E9) Supply and fixing of luminaires like Philips make
FBS 470/236 D6 HF (AG) ,2XPL-L 36W lamp with
all necessary mounting & connection as required
(Make- Philips ,Wipro,& CG)
No 32
Item no. Description Unit Quantity Unit Rate Total
(Rs.) (Rs.)
E10) Supply and fixing of luminaires like Philips make
FCS 518/218, 2XPL-L 18W lamp with all necessary
accessaries like ballast ,mounting arrangment &
connection as required (Make- Philips ,Wipro,& CG)
No 22
E11) Supply and fixing TPN 32A MCB (C curve) with
sheet steel encloser(Industrial type) with socket
necessary connection as required ( Make- L&T, ABB
or other similer make)
No 3
E12) Supply and Installation of Earthing System including
cutting, welding as required of following sizes :
A 25 x 6 mm GS flat Mtr. 20
B 8 SWG GI wire Mtr. 20
E13) Supply and laying of 32 mm dia, 3000 mm long G.I
pipe buried vertically in earth below 1000 mm
ground with earth pite as per IS 3043.
Set 2
E14) Supply and fixing telephone Crone 25 pair with
encloser with necessary connection as required
Set 1
E15) Supply and fixing one set of adopter box with sheet
steel encloser, 125A rated AL bus bar (TPN) at
electrical room with necessary mounting and
connection as required (If required).
Set 1
E16) Supply and fixing one set of 125A,4P,change over
switch with necessary mounting and connection as
required.
Set 1
E17) Supply and fixing one set of call bell at out side of
Maneger room with necessary mounting and
connection as required( Make- Anchor or other
similer make)
No 1
TOTAL
GRAND TOTAL
SL. NO. ITEM OF WORKS AMOUNT(RS.)
1 CIVIL WORKS
2 INTERIOR & FURNISHING WORKS
3 ELECTRICAL WORKS
GRAND TOTAL OF ALL ITEMS
SUMMERY OF ALL ITEMS FOR
INTERIOR WORKS OF BANK OF BARODA ,
JALPAIGURI BRANCH.
Estimate for BOB Jalpaiguri Branch Consultant : ALINDA