Ballostar KHI eng PRINT...8 Component test acc. to EN 488 – KHSVI 300/250 fully welded FFI-Hannover 9 Determination of flow resistance KHSVI 300/250 weld ends Arsenal Research 10

Fluid Control

Edition 2007

Tel. +43 (0)2252 600-0Fax +43 (0)2252 600-359Web: www.klinger.kfc.at

2

3

FunctionOperational principleThe sealing system04.–.05

KLINGER Ballostar –the strong heart Safety through

experience in thesealing and valvemanufacturingMounting options

06sizes and torques

Automation /Torques07

gear with handwheelgear with automaticactuator

Approvals and Tests08

approved quality

Material codesFlow coefficients09

choice of material andsize

Pressure-temperaturelimits10.–.11

how to select theoptimal ball valve

Ballostar range12

summary of types

KLINGER BallostarData sheets13.–.23

ball valves from DN 150to 800 for nominalpressure of 25 or 40 bar

Ball valves withflanges or buttwelding endsBall valves with

flanges – full bore13.–.16

Ball valves with buttwelding ends – full bore17.–.18

Ball valves withflanges – reduced bore19.–.21

Ball valves with buttwelding ends reducedbore22.–.23

Flange dimensions24

Special design25.–.27

for special applications

Ballostar M28

Table of chemicalresistance29.–.33

safety for all fluids

Applications world wide34.–.35

world wide experience

4

Standard internal sealing system

Operational principle of the

Due to the elastic system in the ballvalve, leak-tightness is guaranteed athigh as well as at low pressures. Thesetwo independently working sealing ele-ments are preloaded during assembly.Furthermore they are driven against theball by the differential pressure of themedia. As it is a trunnion mountedball valve, the pressure is not transmit -ted onto the seat rings. The valve can be used bidirectionally.

Expansion caused by heat is compen-sated by the elasticity of the sealingelements.

This elasticity provides continuouslytwo main-sealing areas in the bore upto a certain pressure rate. With the fluidpressing onto the differential surfacesof the sealing element the seat ringis squeezed to the ball surface.As soons as pressure from the clear-ance volume is admitted to the ball andexeeds the nominal pressure, the ball

pushes against the sealing ring on the outlet and keeps it tight to the

atmosphere as well.

Operational principle of KLINGER Ballostar sealing system

Standard sealing system of the operating stem

O-ring (AF)

Supporting disc

Sealing element KFC

Ball

Cover disc

Supporting ring

Locking disc

Hexagon headed bolt

Body

Circlip

U-section sleeve

Bearing bush

O-ring (AF) The usage of other

materials is possible

Bearing bush

O-ring (AF)

Cushion joint

O-ring (AF)Cushion joint

Retaining screw

5

Internal sealing system for superheated water- and steam-applications: KHSVWI/KHWI

Function

When assembling the body and theconnection piece the sealing systemelastically preloads the ball. Two resil -ient sealing elements made of acid re-sistant steel with sealing ring and asealing at the periphery of the support-ing cushions joint, together with theball, form a sealing system that worksin both flow directions. A supportingring protects the resilient sealing ele-ment from overstress. The sealing unitis held by a circlip.

Because of the special sealing systemthe clearance volume of the ball valvecan be drained, ventilated or relievedfrom pressure through a bleeding con-nection. This allows to check if bothsealing rings are tight, after the pres-sure has been relieved (Block & Bleed).

It additionally allows repairs in a de-pressurised pipe section between

The Ballostar ball valve is acknowl-edged by TÜV as double actingshut-off valve in compliance to

Bearing of the ball

Operating-stem sealing for superheated water- and steam-application: Types KHSVWI/KHWI

O-ring(Fluoraz) 799G

Spiral wound gasket 1.4541/graphite/graphite

O-ring (Fluoraz) 799 G

Bearing bush

O-ring (Fluoraz) 799 G

Bearing bush

Cushion joint

Cushion joint

Bush insert

Bush insert

O-ring

Soft-nickel sealing

Hexagon bolt Soft-nickel sealing

Bearing trunnion

Bearing bush

Disc

Locking ring

two ball valves.

TRD and UVV (technical guidelinesfor steam boilers).

O-ring (DN 700, 800)

Hexagon headed boltLocking disc

Supporting ring

Cover disc

Ball

Sealing element KFC

Supporting disc

BodyCirclip

U-section sleeve

Ød1

Ød3

l1 Ød2 (n1)

L4L5

6 In the interest of technical progress, design and dimensions are subject to modification

Ball valve DN 150, DN 200, flange connection acc. to ISO 5211 (F12, F14)

Mounting with bracket Mounting with bare shaft DN 150 200D1 112 150D2 M12 M16D3 69 93,5D4 25 30L1 15 18L2 52 67,5L3 32,8 42,8SW 32 41

F12

Ball valves DN 250 - DN 800, flange connection acc. to ISO 5211Mounting-flange according to ISO 5211.is also dimensioned

Mounting with distance plate

F12, F14 F12, F14

D4

d3

L4

L6

d1

d2

L5

l1

L3

L2

D2 (4x)

D3

L1

F14 F12 L4 76 71 80 86 L5 15 15 14 20 L6 24 19 12,5 18,5

d2 14 18 14 18 d3 85 100 85 100 l1 4 5 4 5

d1 125 140 125 140

L3L1

ØD1

ØD2 (n1)

ØD4

ØD3

s

L2

Mounting with bare shaftDN 250/300 350/400 500/600 700/800

D1 240 280 350 500

D2 18 22 22 33

D3 110 140 140 260

D4 60 80 100 140

L1 13,5 19,5 19,5 19

L2 3 3 3 5

L3 108 128 155 193

n1 4 4 4 4

s 18 18 18 18

ISO 5211 F16 F16 F25 F25 F30 F35

L4 77 97 124 148

L5 9,5 13,5 13,5 13,5 10,5 13

d1 165 254 254 254 298 356

d2 22 18 18 18 22 33

d3 130 200 200 200 230 260

l1 6 6 6 6

n2 4 8 8 8 8 8

F14

7noitacifidomottcejbuserasnoisnemiddnangised,ssergorplacinhcetfotseretniehtnI

Automation of valvesWith automation continuously rising,different types of actuators are beingapplied for which extreme reliability isindispensable.Different kinds of demands can easilybe met with the help of actuators. Mod-ular mounting and a wide range of ac-cessory units which can be updated,make it possible to satisfy individualcustomer requests and adaptions tospecific applications.

Two types of automatic actuators areavailable:

Directly operated – the actuator isdirectly connected with the operatingstem via coupling.

Indirectly operated – the actuatoracts via intermediate gearing.

RecommendationIf the manual force for operating is

higher than 500 Nm we advise you to use a mechanical gear.

Torques for actuator dimensioning

Standard design, KFC seat rings Operating pressure 25 bar:

150 651200 1069250 2083300 3710350 5068400 6251500 8701600 13020700 19320800 31395

Standard design, metal seat Operating pressure 16 bar

DN150 882200 1372250 2646300 4998350 6958400 8526500 10668

Standard design, KFC seat rings Operating pressure 40 bar:

150 1260200 1757250 2905300 5733350 7063400 7987500 11655600 15540700 27510800 36960

Standard design, metal seat Operating pressure 25 bar:

DN150 1176200 1764250 3528300 6272350 8624400 10192500 14063

Suitable actuators Due to the flange connection acc. to

ISO 5211 lots of different gears and actuators from various manufacturers

can be easily attached to Klinger Ballostar KHI ball valves.

Please note that: Generally the above specified values accord to the maximum breakaway (static) torques. At difficult operating conditions (pressure, temperature, media) and if the

valve is operated less than 4-times a year we recommend to contact our technical department. In such cases the corresponding torque value (Mt) has to be multiplied by a safety factor to choose the best suitable actuator.

noitacifidomottcejbuserasnoisnemiddnangised,ssergorplacinhcetfotseretniehtnI8

Product approvals and component tests for KLINGER Ballostar KHI

ynapmocgnitseT:otdragerhtiW

1 Type approval KHI 150-600 application on ships retsigeRs'dyolL

2 Fire-safe test KHI 150.–.600 acc.to API 607/4. Ed TÜV Austria

3 Approval of double shut-off with KHI (meets TRD 601-requirements) TÜV Bavaria

4 Product approval ball valves and valves in Ukraina OC Ketz

5 Product approval ball valves for tanks transboreing hazardous goods inCzech Republic Drazni Urad . .

TGM ViennaRelease for drinking water6

TÜV AustriaCompliance with requirements of PED 97/23/EC is certified7

8 Component test acc. to EN 488 – KHSVI 300/250 fully welded FFI-Hannover

9 Determination of flow resistance KHSVI 300/250 weld ends Arsenal Research

airtsuAVÜTType approval acc. to EN 16101

Quality certificate: TÜV-Bayern confirms that KLINGER Ballostar canbe used as a double acting shut off-device with intermediate relax-ation.The two independent sealing elements,one on each side of the ball with theirpreloaded springforce, keep leaktightat any time – bidirectional and in all

operating conditions – even with vacuum!KLINGER Ballostar makes up for twovalves of any kind! This means bothcost and space savings.

Ballostar KHI: Test acc. to EN 488 Ballostar KHI: Test acc. to EN 488

KLINGER Ballostar: Test acc. toEN 488 at FFIThe district heating-research institute inHannover (FFI) tested theKLINGER Ballostar ball valves acc. toEN 488. During this test the valves areexposed to different kinds of axial ten--sions and pressure loads at a tempera-ture of 140.°C. The leak tighness of body, shaft and seat is tested and the operating torques are determined.

11 Gasapproval GK(SV)HI ÖGVW

12 GOST-Approval for Ballostar ball valves VNIIIMASH

9noitacifidomottcejbuserasnoisnemiddnangised,ssergorplacinhcetfotseretniehtnI

Material codeMaterial code Body End piece Internals Colour of body

yergstrapyollareppoctuohtiWnoritsaCnoritsaCIII

VII Cast steel Cast steel Copper alloy parts included blue

VIII Cast steel Cast steel Without copper alloy parts blue

leetstnatsiserdicAleetstnatsiserdicAX Acid resistant steel, nuts andscrews steel galvanized unpainted

Xc Acid resistant steel Acid resistant steel Acid resistant steel unpainted

Primery criterion for the material code is the basic material of the body and end piece.

Flow coefficients and zeta-values, full boreDN 150 200 250 300 350 400 500 600 700 800

kV 4203 8131 13630 20590 29540 38582 59978 95695 118940 154245

0,045 0,038 0,033 0,030 0,027 0,027 0,025 0,025 0,025 0,025

Flow coefficients and zeta-values, casted version with reduced boreDN 150/125 200/150 250/200 300/250 350/300 400/350 500/400 600/500 700/600 800/700

kV 1642 2920 4640 6682 9256 12090 19604 28230 39186 51182

0,3 0,3 0,29 0,29 0,28 0,28 0,26 0,26 0,25 0,25

= Zeta-valuekV = flow coefficient (m 3/h)Graphs and exact flow calculations for all KLINGER valves are available on request.

The kV-value represents a characteristicsize for shut-off and control devices.This shows the flow rate of H2O in m 3/hfrom 5.–.30.°C with a pressure differ-ence

p = 1 bar at the valve.

Countries which use the inch as mea-suring unit the cV-value replaces thekV-value. This value indicates howmany US gal. of water, at the tempera-ture of 60°F and a loss of pressure of1 psi, pass the valve every minute.

cV = 1,1558 KVkV = 0,8652 CV

Variation 1: ball valve with reduced bore

Dimension: 800/700 cast version

-value: 0,25kV-value: 51 182 m 3/h

Variation 2: ball valve reduced with welding cones

Dimension: DN 800/700

kV-value: 58 919 m 3/h-value 0,189

Observe the relation:

kv

kvfull port

redued port

full port

redued port

=


Pressure-temperature limitsThe PT-diagram clearly shows what im-pact the material of body, sealing, bear-ings and screws has on the applicationrange of the ball valve.Place your operating point in the diagramfield to see if the safety margins meetyour requirements.A decreasing operating pressure in thenominal pressure range increases thefield of applications in the temperurerangeIf you choose your ball valve in this wayyou optimize the economy of the valve.

Indicated temperatures are limiting valueswhich have always to be considered in connec-tion with the medium and the respective opera-tional pressure. Admitted continuous tempera-tures are always within these limiting values:

1) Temperatures for studs 8.8, A4-70, A2-70 and below -60°C for balls only austenitic

materials here to be used

2) Pressure/temperature ratings acc. to EN 12516-1.

3) According to customer request, with specialgaskets

O-rings 799G, spiral wound gasketO-ring compound: AF3)

Stud bolt A4-70 1)Stud bolt 8.8 1)

Stud bolt A2-70 1)

m.c. VII: non-ferrous parts possible

m.c. VIII: free of non-ferrous parts

Spec

ial t

ypes

: KHW

I and

KHS

VWI

Stan

dard

type

s: K

HI a

nd K

HSVI

11

Indicated temperatures are limiting values whichhave always to be considered in combination with themedium and the respective operational pressure. Ad-mitted continuous temperatures are always withinthese limiting values.

1) Application limits acc. to EN 12516-1 (14 E0)

Indicated temperatures are limiting values whichhave always to be considered in connection with themedium and the respective operational pressure. Ad-mitted continuous temperatures are always withinthese limiting values:

O-rings: AF, VitonStud bolt A4Stud bolt 8.8

O-rings: AFStud bolt A4

O-rings: Fluoraz 799G, spiral wound gasket

200

Stud bolt 8.8 2)

2)

2) M.c. X = acid resistant, stainless steel: Connection screws 8.8 Fe/Ni 5P (or E2P)

M.c. Xc all components made of stainless steel!

1) Application limits acc. to ISO 7005-2M

. c. I

II (fr

ee o

f non

-ferro

us m

etal

par

ts)

M. c

. III

(non

-ferro

us m

etal

par

ts p

ossi

ble)

Stan

dard

type

s: K

HI a

nd K

HSVI

Spec

ial t

ypes

: KHW

I and

KHS

VWI

12

snoitcennoCevlavllaB

Page Type DN PN Material Type Standard 1) Dimensions 2)

Ball valves with flange – full bore

13 KHI 150.–. 200 25, 40 cast steel flange EN 1092-1 EN 558-1/GR 12

. .14 KHI 150

.

–

.

350 25, 40 cast steel flange EN 1092-1 EN 558-1/GR 12

.

15 KHI 150 – 400 25, 40 acid resistant stee l flange EN 1092-1 EN 558-1/GR 12

16 KHI 400 – 800 25, 40 cast steel flange EN 1092-1 EN 558-1/GR 12

Ball valves with welding ends – full bore

17 KHSVI 150.–.200 40 cast steel butt weld end EN 12627 EN 12982/GR 63 3)

18 KHSVI 150.–.800 40 cast steel butt weld end EN 12627 EN 12982/GR 63 3)

Ball valves with flanges – reduced bore

19 KHI 200/150 16 cast iron flange EN 1092-2 EN 558-1/GR 27 4)

20 KHI 150/125.–.250/200 25 cast steel flange EN 1092-1 EN 558-1/GR 27 4)

20 KHI 150/125.–.250/200 25 acid resistant steel flange EN 1092-1 EN 558-1/GR 27 4)

21 KHI 150/125.–.300/250 25 cast steel flange EN 1092-1 EN 558-1/GR 27 4)

21 KHI 150/125.–.300/250 25 acid resistant steel flange EN 1092-1 EN 558-1/GR 27 4)

Ball valves with welding ends – reduced bore

22 KHSVI Cones in all sizes andreductions 40 cast steel butt weld end EN 12627

23 KHSVI 300/250.–.800/700 40 cast steel butt weld end EN 12627 EN 12982/GR 63 3)

Note:1) Flange dimensions see page 242) Face-to-face dimensions acc. to EN 558-1/GR 12 identical to ISO 5752-R123) End-to-end dimensions acc. to EN 12982/GR 63 identical to ANSI B 16.104) Face-to-face dimensions acc. to EN 558-1/GR 27 identical to DIN 3202-F5

Assembly of big sized Klinger Ballostar KHSVI ball valves

31noitacifidomottcejbuserasnoisnemiddnangised,ssergorplacinhcetfotseretniehtnImmnidetacidnierasnoisnemidllA

Pressure- and temperature limits see page 10.–.11

actuators see page 7

Suggested order specification

Ball valve PN 25 or PN 40Split body, full bore with supported ball,two independent sealing elements, mainsealing element KFC is metallically en-closed on three sides, operating stemmade of acid resistant steel, mainte-nance-free operating-stem seal made ofAF, pressure possible on both sides,body and end piece made of cast steelGP 240 GH, overall length acc. to EN558.–.1/GR12, operated with hand lever.

Make: KLINGERType: KHI-VII, VIII,for DN 150.–.200

Ordering example:KHI 150-VII – KFC/AF, PN 25KHI 150-VII – KFC/AF, PN 40

KHI150.–.200PN 25material-code VII, VIII

PN 40material-code VII, VIII

Face-to-face dimensionsacc. to EN 558-1/GR 12

Part name Material code VII1 Body GP 240 GH2 Flanged end GP 240 GH3 Operating stem 1.4104

4 Ball EN-JS 1030 Fe/Cr30.f,mt

5 Trunnion 1.41047 Flange GP 240 GH8 Bush insert OT 1.05539 Valve lever St / polyamid

10 Bush insert UT 1.055312 Washer 1.440113 Gasket soft nickel14 Gasket soft nickel15 Cushions joint KFC-2516 Cushions joint K-SIL17 O-ring AF 3)18 O-ring AF 3)19 O-ring AF 3)

Part name Material code VII20 O-ring AF 3)21 U-section sleeve KFC-2522 Sealing element VII-KFC23 Circlip 1.4401.0724 Supporting ring 0.602025 Washer St29 Locking ring 1.4122 1)30 Hexagon bolt 5.631 Hexagon bolt 5.632 Hexagon nut 833 Stud bolt 8.835 Hexagon bolt 1.054036 Feather key 1.0052.0738 Bearing bush St/Bz/Flon 2)39 Bearing bush St/Bz/Flon 2)

1) not applicable for DN 1502) material code VIII: AISI 316L P90

PN 25, PN 40Overall dimension in mmDNd

L1 H H1 Gweightin kg

150 394 263 166 800 85200 457 340 218 1000 150

Flange dimensions see page 24

Leak tightness through the bore tested acc. to EN ISO 12266-1 P12.

External leak tightness testet acc to EN ISO 12266-1 P11.

Strength determined acc. to EN ISO 12266-1 P10.

3) O-ring compound of standard version

noitacifidomottcejbuserasnoisnemiddnangised,ssergorplacinhcetfotseretniehtnImmnidetacidnierasnoisnemidllA41



KHI150.–.350




Suggested order specificaton

Ball valve PN 25 or PN 40Split body, full bore with supported balltwo independent sealing elements, mainsealing element KFC is metallically en-closed on three sides, operating stemmade of acid resistant steel, mainte-nance-free operating stem-sealingmade of AF, pressure possible on bothsides, body and end piece made of caststeel GP 240 GH, overall dimensionacc. to EN 558.–.1/GR 12, operated viaworm gear.

Make: KLINGERType: KHI-VII, VIII, for DN 150.–.350

Ordering example:KHI 150-VII – KFC/AF, PN 25KHI 150-VII – KFC/AF, PN 40with mechanical gear

Part names Material code VII1 Body GP 240 GH2 Flanged end- piece GP 240 GH3 Operating stem 1.4104


5 Trunnion 1.41047 Flange GP 240 GH8 Bush insert OT 1.055310 Bush insert UT 1.055312 Washer 1.4401 1)13 Gasket soft nickel14 Gasket soft nickel15 Cushions joint KFC-2516 Cushions joint K-SIL17 O-ring AF 3)18 O-ring AF 3)19 O-ring AF 3)20 O-ring AF 3)21 U-section sleeve KFC-2522 Sealing element VII-KFC

Part names Material code VII23 Circlip 1.4401.0724 Supporting ring 0.602029 Locking ring 1.4122 1)31 Hex. head cap screw 10.932 Hexagon nut 833 Stud bolt 8.834 Slotted cheese headscrew A4

35 Hexagon bolt 1.054036 Feather key 1.0052.0737 Feather key 1.0052.0738 Bearing bush St/Bz/Flon 2)39 Bearing bush St/Bz/Flon 2)43 Hex. head cap screw A444 Flange St . .45 Gear drive

1) not applicable for DN 1502) material code VIII: AISI316L P90

PN 25Overall dimension in mm

DN L1 H1 H 4) A 4) weightin kg 5) in kg 6)

150 394 166 509 315 85 115200 457 218 584 315 150 190250 533 260 651 400 220 260300 610 290 859 800 380 420350 686 353 750 400 580 620


DN L1 H1 H 4) A 4) weightin kg 5) in kg 6)

150 394 166 475 315 85 125200 457 218 606 400 160 200250 533 260 599 315 240 280300 610 290 676 400 410 450350 686 353 767 400 620 660

5) without gear6) complete with AUMA-gear

Dimension A, H: depending on geartype Torques see summary page 7Flange dimensions see page 24Mounting eyelet for DN 350 andDN 400

4) measurements relate to AUMA-gear








KHI150.–.400PN 25material-code Xc

PN 40material-code X



Ball valve PN 25Split body, full bore with supported ball,two independent sealing elements, mainsealing element KFC is metallically en-closed on three sides, operating stemmade of stainless, acid resistant steel1.4401 maintenance-free operatingstem sealing made of AF, pressurepossible on both sides, body andend piece made of acid resistant steel1.4408, overall length to EN 558-1/GR12,operated via worm gear.

Make: KLINGERType: KHI-Xc, for DN 150.–.400.

Ordering example:KHI 150-Xc – KFC/AF, PN 25with mechanical gear

Part name Material code Xc1 Body 1.44082 Flanged end 1.44083 Operating stem 1.44014 Ball 1.44085 Trunnion 1.44017 Flange 1.44088 Bush insert OT 1.4401

10 Bush insert UT 1.4401 soft nitriding12 Washer 1.4401 1)13 Gasket soft nickel14 Gasket soft nickel15 Cushions joint KFC-2516 Cushions joint K-SIL17 O-ring AF18 O-ring AF19 O-ring AF20 O-ring AF21 U-section sleeve KFC-25

Part name Material code Xc22 Sealing element X-KFC23 Circlip 1.4401.0724 Supporting ring 1.440829 Locking ring 1.4122 1)31 Hex. head cap screw A432 Hexagon nut A4 2)33 Stud bolt A4.–.70 2)34 Slotted cheese hd screw 1.440135 Hexagon bolt 1.457136 Feather key 1.440137 Feather key 1.440138 Bearing bush AISI316L P9039 Bearing bush AISI316L P9043 Hex. head cap screw A444 Flange 1.440145 Gear drive

1) Not applicable for DN 1502) Material 8.8 Fe/Ni 5P (or E2P)


DN L1 H1 H 4) A 4)weight

in kg 5) in kg 6)150 394 166 475 315 85 115200 457 218 606 400 150 190250 533 260 599 315 220 260300 610 290 676 400 380 420350 686 353 767 400 580 620400 762 370 769 400 800 891

4) measurements relate to Auma-gear



in kg 5) in kg 6)150 394 166 475 315 85 125200 457 218 606 400 160 200250 533 260 599 315 240 280300 610 290 676 400 410 450350 686 353 767 400 620 660400 762 370 769 400 856 947

5) without gear 6) complete with AUMA-gear

Dimension A, H: depending on gear typeTorques see summary page 7Flange dimensions see page 24Mounting eyelet for DN 350 only





3)3)3)3)




KHI400.–.800





Ball valve PN 25Split body, full bore with supported balltwo independent sealing elements, mainsealing element KFC is metallically en-closed on three sides, operating stemmade of acid resistant steel, mainte-nance-free operating stem seal made ofAF, pressure possible on both sides,body and end piece made of cast steelGP 240 GH, overall dimension acc. toEN 558.–.1/GR 12, operated via wormgear.Make: KLINGERType: KHI-VII, VIII,for DN 400.–.800

Ordering example:KHSVI 400-VII – KFC/AF, PN 25with mechanical gear

Part names Material code VII1 Body GP 240 GH2 Flanged end GP 240 GH3 Operating stem 1.4104

4 Ball EN-JS 1030Fe/Cr30.f, mt

5 Trunnion 1.41047 Flange St8 Bush insert OT 1.055310 Bush insert UT 1.055312 Washer 1.4401 1)13 Gasket Weichnickel14 Gasket Weichnickel15 Cushions joint KFC-2516 Cushions joint K-SIL17 O-ring AF18 O-ring AF19 O-ring AF20 O-ring AF21 U-section sleeve KFC-2522 Sealing element VII-KFC

Part names Material code VII23 Circlip 1.4401.0724 Supporting ring 0.6020

1)30 Cheese headed screw A431 Hex. head cap screw 10.932 Hexagon nut 833 Stud bolt 8.834 Slotted cheese head screw A435 Hexagon bolt 1.054036 Feather key 1.0052.0737 Feather key 1.0052.0738 Bearing bush St/Bz/Flon 2)39 Bearing bush St/Bz/Flon 2)43 Hex. head cap screw 10.944 Flange St .45 Gear drive

1) not applicable for DN 1502) material VIII: AISI316L P90



in kg 5) in kg 6)400 762 370 769 400 800 891500 914 465 870 400 1200 1291600 1067 528 1114 630 1750 1910700 1245 640 1368 800 3100 3260800 1372 710 1464 800 4850 5146

3) measurements relate to Auma-gear



in kg 5) in kg 6)400 762 370 769 400 856 947500 914 465 870 400 1330 1490600 1067 528 1114 630 1863 2023700 1245 640 1368 800 3350 2646800 1372 710 1464 800 5055 5351


Dimension A, H: depending on gear typeTorques see summary page 7Flange dimensions see page 24Mounting eyelet for all sizes





3)3)3)3)

29 Locking ring 1.4122




KHSVI150.–.200PN 40material-code VII, VIII

End-to-end dimensionsacc. to EN 12982/GR 63resp ANSI B16.10


Ball valve PN 40Split body, full bore with supported ball,two independent elements, mainsealing element KFC is metallically en-closed on three sides, operating stemmade of acid resistant steel,mainte-nance-free operating-stem seal made ofAF, pressure possible on both sides,body and end piece made of steel GP240 GH, overall length acc. to ANSIB16.10 class 300 and EN 12982/GR 63,butt welding ends acc. to customer re-quest.Make: KLINGERType: KHSVI-VII, VIII, for DN 150.–.200

Ordering example:KHSVI 150-VII – KFC/AF, PN 40

Part name Material code VII1 Body GP 240 GH2 End piece GP 240 GH3 Operating stem 1.4104


5 Trunnion 1.41047 Flange GP 240 GH8 Bush insert OT 1.05539 Lever St/PA yellow

10 Bush insert UT 1.055312 Washer 1.440113 Gasket soft-nickel14 Gasket soft-nickel15 Cushions joint KFC-2516 Cushions joint K-SIL17.O-ring AF18.O-ring AF19.O-ring AF

Part name Material code VII20. O-ring AF21 U-section sleeve KFC-2522 Sealing element VII-KFC23 Circlip 1.4401 K24 Supporting ring 0.602025 Washer St29 Locking ring 1.4122 1)30 Hexagon bolt 5.631 Hexagon bolt 5.632 hexagon nut 833 stud bolt 8.835 Hexagon bolt 1.054036 Feather key 1.0052.0738 Bearing bush St/Bz/Flon 2)39 Bearing bush St/Bz/Flon 2)

1) Not applicable for DN 1502) Materialf VIII: 38 AISI316L/P90 39 AISI316L/P90


DN L H H1 Gweightca. kg

150 457 263 166 800 68200 521 340 218 1000 130

PN 40Connection dimensions in mm „ Standard“

DN d d1 s b150 150 168,3 6,65 20200 200 219,1 8,05 20





3)3)3)

3)





Ball valve PN 40Split body, full bore with supported ball,two independent sealing elements, mainsealing element KFC is metallically en-closed on three sides, operating stemmade of acid resistant steel, mainte-nance-free operating-stem seal made ofAF, pressure possible on both sides,body and end piece made from caststeel, overall length acc. to ANSIB16.10 class 300 and EN 12982/GR 63,butt welding ends acc. to customer re-quest, operated via worm gear.Make: KLINGERType: KHSVI-VII, VIII, for DN 150.–

.

800

Ordering example:KHSVI 350-VII – KFC/AF, PN 40with mechanical gear

Part names Material code VII1 Body GP 240 GH2 End piece GP 240 GH3 Operating stem 1.4104


5 Trunnion 1.41047 Flange St8 Bush insert OT 1.0553

10 Bush insert UT 1.055312 Washer 1.440113 Gasket soft nickel14 Gasket soft nickel15 Cushions joint KFC-2516 Cushions joint K-SIL17 O-ring AF18 O-ring AF19 O-ring AF20 O-ring AF21 U-section sleeve KFC-25

Part names Material code VII22 Sealing element VII-KFC23 Circlip 1.4401 K24 Supporting ring 0.602029 Locking ring 1.4122 1)31 Hex-s. head cap screw 10.932 Hexagon nut 833 Stud bolt 8.834 Cheese head bolt A435 Hexagon bolt 1.054036 and 37 feather key 1.0052.0738 Bearing bush St/Bz/Flon 2)39 Bearing bush St/Bz/Flon 2)43 Hex-s. head cap screw A444 Flange St . .45 Gear

1) Not applicable for DN 1502) Material VIII: 38 AISI316L/P90 39 AISI316L/P90

DN Overall dimension in mm Connection dimensions in mm Stan -dard”

weight

L H1 H A d d1 s b in kg 4) in kg 5)150 457 166 509 315 150 168,3 6,65 20 68 108200 521 218 584 315 200 219,1 8,05 20 130 170250 559 260 651 400 250 273 8,50 20 200 240300 635 290 676350 762 353 750 400 334 355,6 10,80 20 555 595400 838 370 769 400 386 406.4 10,20 25 760 851500 991 465 1010 630 476 508 16,00 25 1150 1310600 1143 528 1114 630 575 610 17,5 25 1700 1860700 1346 640 1368 800 676 711 17,5 25 3000 3296800 1524 710 1464 800 775 813 19 25 4700 4996


KHSVI150.–.800


End-to-end dimensionsacc. to EN 12982/GR 63

resp ANSI B16.10

Dimension A, H: depending on gear typeTorques see summary page 7Mounting eyelet for DN 350 to DN 800





3)3)3)3)

400 300 323,9 9,45 20 355 395




KHI200/150PN 16material-code III


PN 16

Overall dimension in mm

d1 d L1 H G H1 D c3 k L no g fweightca. kg

200 150 400 263 650 166 340 30 295 22 12 268 3 90

Part names Material code III

1 Body EN-JL 1040

2 Flanged end EN-JL 1040

3 Operating stem 1.4104

4 Ball EN-JS 1030 Fe/Cr30.f, mt

5 Trunnion 1.4104

7 Flange GP 240 GH

8 Bush insert OT 1.0553

9 Lever St/PA rot

10 Bush insert UT 1.0553

12 Washer 1.4401

13 Gasket Soft nickel

14 Gasket Soft nickel

15 Cushions joint KFC-25

16 Cushions joint K-SIL

17 O-ring AF

18 O-ring AF

Part names Material code III

19 O-ring AF

20 O-ring AF

21 U-section sleeve KFC 25

22 Sealing element VII-KFC

23 Circlip 1.4401 K

24 Supporting ring 0.6020

25 Washer St

29 Locking ring 1.4122 1)

30 Hexagon bolt 5.6

31 Hexagon bolt 5.6

32 Hexagon nut 5

33 Stud bolt 5.6

35 Hexagon bolt 8.8

36 Feather key 1.0052.07

38 Bearing bush AISI 316 L / P 90

39 Bearing bush AISI 316 L / P 90


Ball valve PN 16Split body, reduced bore with sup-ported ball, two independent sealingelements, main sealing element KFC ismetallically enclosed on three sides,operating stem made of acid resistantsteel, maintenance-free operating stemseal made of AF, pressure possible onboth sides, body and flanged end madeof cast iron EN-JL 1040, overall lengthacc. to EN 558.–.1/GR 27.Make: KLINGERType: KHI-III, for DN 200/150

Ordering example:KHI 200/150-III – KFC/AF, PN 16





1) Not applicable for DN 1502) O-ring compound of standard version

2)2)

2)2)




KHI150/125.–

250/200PN 25

material-code VII,VIII, Xc



Ball valve PN 25Split body, reduced bore with suppor-ted ball, two independent sealing ele-ments, main sealing element KFC ismetallically enclosed on three sides,operating stem made of acid resistantsteel 1.4408, maintenance-free operatingstem made of AF, pressure possible onboth sides, body and end piece made ofcast steel GP 240 GH or stainless,acid-resistant steel 1.4408, overalllength acc. to EN 558.–.1/GR 27.Make: KLINGERType: KHI-VII, VIII, Xcfor DN 150/125.–.250/200

Ordering example:KHI 150/125-VII – KFC/AF, PN 25KHI 150/125-Xc – KFC/AF, PN 25

Part nameMaterial codeVII Xc

1 Body GP 240 GH 1.44082 Flanged end GP 240 GH 1.44083 Operating stem 1.4104 1.4401

4 Ball EN-JS 1030Fe/Cr30.f, mt 1.4408

5 Trunnion 1.4104 1.44017 Flange GP 240 GH 1.4401

8 Bush insert OT 1.0553 1.4401 softnitriding

9 Lever St/polyamid St/poly-amid

10 Bush insert UT 1.0553 1.4401 softnitriding

12 Washer 1.4401 1.440113 Gasket soft nickel soft nickel14 Gasket soft nickel soft nickel15 Cushions joint KFC-25 KFC-2516 Cushions joint K-SIL K-SIL17 O-ring AF AF18 O-ring AF AF19 O-ring AF AF

Part nameMaterial codeVII Xc

20 O-ring AF AF21 U-section sleeve KFC-25 KFC-2522 Sealing element VII-KFC X-KFC23 Circlip 1.4401.07 1.4401.0724 Supporting ring 0.6020 1.440825 Washer St 1.457129 Locking ring 1.4122 1) 1.4122 1)30 Hexagon bolt 5.6 A431 Hexagon bolt 5.6 A432 Hexagon nut 8 A433 Stud bolt 8.8 A435 Hexagon bolt 1.0540 1.457136 Feather key 1.0052.07 1.4401

38 Bearing bush St/Bz/Flon 2) AISI316LP90

39 Bearing bush St/Bz/Flon 2) AISI316LP90

1) Not applicable for DN 150/125.+.200/1502) Material VIII: AISI316L P90

PN 25Overall dimension in mmDN d/d1 L1 H H1 G weight in kg150/125 350 155 251 650 76200/150 400 167 263 800 105250/200 450 217 340 1000 177






1) 1)

3)3)3)

3)3)3)

3) 3)


KHI 150/125.–300/250PN 25material-code VII, VIII, Xc



Ball valve PN 25Split body, reduced bore with suppor-ted ball, two independent sealing ele-ments, main sealing element KFC ismetallically enclosed on three sides,operating stem made of acid resistantsteel 1.4401, maintenance-free operat-ing stem made of AF, pressure possiblefrom both sides, body and end piecemade of cast steel GP 240 GH or acidresistant steel 1.4408, overall lengthacc. to EN 558.–.1/GR 27, operated viaworm gear.Make: KLINGERType: KHI-VII, VIII, Xc, for DN150/125.–.300/250

Ordering example:KHI 150/125-VII – KFC/AF, PN 25KHI 150/125-XcI – KFC/AF, PN 25with mechanical gear

Part namesMaterial codeVII Xc

1 Body GP 240 GH 1.44082 Flanged end GP 240 GH 1.44083 Operating stem 1.4104 1.4401

4 BallEN-JS 1030 Fe/Cr30.f,mt

1.4408

5 Trunnion 1.4104 1.44017 Flange GP 240 GH 1.4408

8 Bush insert OT 1.0553 1.4401 softnitrited

10 Bush insert UT 1.0553 1.4401 softnitrited

12 Washer 1.4401 1.440113 Gasket soft-nickel soft-nickel14 Gasket soft-nickel soft-nickel15 Cushions joint KFC-25 KFC-2516 Cushions joint K-SIL K-SIL17 O-ring AF AF18 O-ring AF AF19 O-ring AF AF20 O-ring AF AF

Part namesMaterial codeVII Xc

21 U-section sleeve KFC-25 KFC-2522 Sealing element VII-KFC X-KFC23 Circlip 1.4401.07 1.4401.0724 Supporting ring 0.6020 1.440829 Locking ring 1.4122 1) 1.431031 Hexagon bolt 5.6 A432 Hexagon nut 5 A433 Stud bolt 5.6 A435 Hexagon bolt 1.0540 A436 Feather key 1.0052.07 1.4401

38 Bearing bush St/Bz/Flon2)

AISI316LP90

39 Bearing bush St/Bz/Flon2)

AISI316LP90

42 Coupling St St/FeNi43 Hexagong headedbolt 10.9 A4

44 Flange St 1.440145 Gear drive

1) Not applicable for DN 150/125.+.200/150

PN 25DN d/d1 L1 H1 H A weight in kg 3) weight in kg 4)150/125 350 155 475 315 76 106200/150 400 167 606 400 105 135250/200 450 217 599 315 177 217300/250 500 268 676 400 254 294


Dimension A, H: depending on gear typeTorques see summary page 7Flange dimensions see page 24




1)1)

2) 2)2)2)2)

2)2)2) 2) O-ring compound of standard version


KHSVIPN 40

material-code VII, VIII

Suggested order specificationBall valve PN 40Split body, full bore with diffusor/con-

fusor and supported ball, twoindependent sealing elements, the mainsealing element KFC is metallically en-closed on three sides, operating stemmade of acid resistant steel, mainte-nance-free operation stem made of AF,pressure possible on both sides, bodyand end piece made of cast steel, buttweld end acc. to customer request, op-erated via worm gear.Make : KLINGERType: KHSVI-VII, VIII




10 Bush insert UT 1.055312 Washer 1.440113 Gasket Soft-nickel14 Gasket Soft-nickel15 Cushions joint KFC-2516 Cushions joint K-SIL17 O-ring AF18 O-ring AF19 O-ring AF20 O-ring AF21 U-section sleeve KFC-25

Part names Material code VII22 Sealing element VII-KFC23 Circlip 1.4401.0724 Supporting ring 0.602029 Locking ring 1.412230 Hex. head cap screw A431 Hex. head cap screw 10.932 Hexagon nut 833 Stud bolt 8.834 Slotted cheese headscrew A4

35 Hexagon bolt 1.054036 Feather key 1.0052.0737 Feather key 1.0052.0738 Bearing bush St/Bz/Flon 1)39 Bearing bush St/Bz/Flon 1)44 Flange St45 Gear drive46 Reducing cone St

1) Material VIII, AISI316L P90

Ball valves with extended buttweld-ends are available in all sizes. Uponcustomer request also available with re-duced piece acc. to DIN 2616 T2 or inspecial sizes.




2)2)2)2)


23

KHSVI300/250.–800/700PN 40material-code VII, VIII

End-to-end dimensionsacc. to EN 12982/GR 63


Ball valve PN 40Split body, full bore with supported ball,two independent sealing elements, mainsealing element KFC is metallically en-closed on three sides, operating stemmade of acid resistant steel, mainte-nance-free operating-stem sealingmade of AF, pressure possible on bothsides, body and end piece made of caststeel, overall length acc. to ANSIB16.10 Class 300 and EN12982/GR 63,butt-weld ends acc. to customer re-quest, operated via worm gear.

Make : KLINGERType: KHSVI-VII, VIII, for DN700/600.–.1100/800

Ordering example:KHSVI 300/250-VII – KFC/AF,PN 40with mechanical gear


4 Ball EN-JS 1030Fe/Cr30.f, mt


10 Bush insert UT 1.055312 Washer 1.440113 Gasket soft nickel14 Gasket soft nickel15 Cushions joint KFC-2516 Cushions joint K-SIL17 O-ring AF18 O-ring AF19 O-ring AF20 O-ring AF21 U-section sleeve KFC-25

Part names Material code VII22 Sealing element VII-KFC23 Circlip 1.4401.0724 Supporting ring 0.602029 Locking ring 1.412230 Cheese headed screw A431 Cheese headed screw 10.932 Hexagon nut 833 Stud bolt 8.834 Cheese headed screw A435 Hexagon bolt 1.054036 Feather key 1.0052.0737 Feather key 1.0052.0738 Bearing bush St/Bz/Flon 1)39 Bearing bush St/Bz/Flon 1)44 Flange St45 Gear drive

1) Material VIII: AISI316L P90

Dimension A, H: depending on gear typeTorques see summary page 7Mounting eyelet from DN 350


DN d d1 b s L H1 H A weightin kg 3) in kg 4)

300/250 250 323,9 20 9,45 635 260 651 400 232 272350/300 300 355,6 20 10,8 762 290 859 400 405 445400/350 350 406,4 25 10,2 838 353 750 400 610 650500/400 475 610 25 17,5 1143 465 1010 630 1280 1371

700/600 585 711 25 17,5 1346 528 1114 630 1390 1550800/700 676 813 25 19 1524 640 1368 800 3350 3510






2)2)2)2)

600/500 475 610 25 17,5 1143 465 1010 630 1280 1371

24

Flange dimensions for PN 25gnicafegnalFnoitcennoCeziS

DN D c3 k l Nr. g f

150 300 28 250 26 8 218 3

200 360 30 310 26 12 278 3

250 425 32 370 30 12 335 3

300 485 34 430 30 16 395 4

350 555 38 490 33 16 450 4

400 620 40 550 36 16 505 4

500*) 730 44 660 36 20 615 4

600*) 845 46 770 39 20 720 5

700*) 960 50 875 42 24 820 5

800*) 1085 54 990 48 24 930 5

*) Dimensions acc. to DIN 2544

Flange dimensions for PN 40gnicafegnalFnoitcennoCeziS

DN D c3 k l Nr. g f

150 300 28 250 26 8 218 3

200 375 34 320 30 12 285 3

250 450 38 385 33 12 345 3

300 515 42 450 33 16 410 4

350 580 46 510 36 16 465 4

400 660 50 585 39 16 535 4

500*) 755 52 670 42 20 615 4

600*) 890 60 795 48 20 735 5

700*) 995 64 900 48 24 840 5

800*) 1140 72 1030 56 24 960 5

*) Dimensions acc. to DIN 2545

No.Number of

bolt holes

ZturningRz 12,5 - Rz 50

Z

25

Special designOur main concern is the customer andhis needs. In close cooperation we cre-ate innovative and individual solutionsin order to satisfy every individual de-mand. Among other things we offerspecial designs and accessories as fol-lows:• Regulation blind (equal percentage,

linear, u.a.)

• Vacuum application up to10. .-6 mbar l/s

• Steam application

• Valves for Benton’Air® pressurisedslurry tunnel drilling machines

• Oxygen application• Metal seated valves for abrasive

medium

• Heating jacket• Bypass design• Drain-, air-relief- and flushing-

connections• Underground installation

(extended operating stem)

Table of measurements (in mm)

150 50 407 382 355 26.9 2.3 KHA-SL 20 VIII PN100

200 75 444 420 381 26.9 2.3 KHA-SL 20 VIII PN100

250 80 509 484 429 33.7 2.6 KHA-SL 25 VIII PN63

300 90 545 520 455 33.7 2.6 KHA-SL 25 VIII PN63

350 110 575 550 475 33.7 2.6 KHA-SL 25 VIII PN63

400 115 608 583 499 33.7 2.6 KHA-SL 25 VIII PN63

450 130 870 663 706 60.3 2.9 KHA-SL 50 VIII PN40

500 130 870 663 706 60.3 2.9 KHA-SL 50 VIII PN40

600 140 950 743 763 60.3 2.9 KHA-SL 50 VIII PN40

700 140 1031 824 820 60.3 2.9 KHA-SL 50 VIII PN40

800 250 1071 864 848 60.3 2.9 KHA-SL 50 VIII PN40

• The drain cock should only beopened if the ball valve is closed.

• To avoid injury it is recommended toconnect the drain cock to a drainpipe.

• Applied for superheated water it hasto be considered that, depending onthe valve size, the draining procedurelasts for some time.

• With the drain cock it is possibleto check the “block & bleed” func-tion, i..e. the ball valve can be testedwhether it is leaktight.

• Fully welded design

• GKHI for gas application (ÖVGW approved): DN 150-800

26

These ball valves are approved acc. to EN 488 (underground installa-tion), upon request even pre-insulated – see adjoining pictures. If re-quired equipped with telescopic stem extension.

Ballostar ball valves pre-insulated, shown before andduring the installation into a district heating network

Surface

Square protection cap 27/32

Position indicator ECL3

Telescope extension H=1,2 m ... 150 mm

27

Ball valves KHSVI 150. –. 800 with insulating stem extension and buried fitting “RIGID”or “TELESCOPE” and mechanical gear plus position indicator

Option 3Mechanical gear with rigid operation-stem extension with angular gear andhand-wheel operation or square 27/32

Option 4Mechanical gear with angular gear,hand-wheel operation resp. square27/32

Option 2Mechanical gear with rigid or telescopeextensionsquare 27/32 operated with T-keyDIN3223 type C (alternatively hexagonsquare 32)

Option 1Mechanical gear with angular gear andposition indicator rigid or telescope ex-tensionsquare27/32 operated with T-keyDIN3223 type C (alternatively hexagonsquare 32)

Option 1 Option 2 Option 3

Option 4

acco

rdin

g to

cus

tom

ers

wish

H

Top flange acc. to ISO 5211

protection cap for square end 27/32(alternative hexagonal end 32 resp. 50

Ball valve

Ball valve

Ball valve Ball valve

28

Economically optimised and future-proofed because of modular design

Due to the trunnion mounted ball, single sided loads, which are actingon sealing elements, are avoided. This guarantees high leak tightnessand increases the service life.Worn sealing elements can be substi-tuted on the spot, economically,without a specialist or KLINGER techni-cian. Regarding stock keeping it meansthat you only have to store sealing ele-ments or sealing kits and not completeball valves.Ballostar ball valves which are alreadyon stock can be fitted supplimentarywith metal sealing elements. This en-sures consistency of design throughoutthe plant.

Special surface coatings of the ball• Hard-chrome• Chemical nickel• Wolframcarbid

Special surface coatings should be choosed acc. to requirements of the operating media.

29

The recommendations contained in the table should help youto choose suitable materials and types. We cannot assume aguarantee since function and durability of the products arelargely dependent on factors over which the manufacturer has noinfluence.In the event of specific conditions of approval, these must be ob-served. Please contact us for any support. Whenever solids are named in the list, what is meant are their aqueous suspensions.

Names of metallic materials,codes and code numbers accordingsolutions or to DIN-standard.

EN-JL1040 grey cast iron acc. to EN 1561GP 240 GH heat resisted cast steel acc. to EN 102131.4401 nickel-chromium molybdenum steel1.4408 nickel-chromium molybdenum steel1.4571 stabilized nickel-chromium molybdenum steel

Names of materials for seals:AF AFLASK-Flon Klingerflon®PTFEKFC Klingerflon®carbon-reinforcedMetal 1.4436 sealing ring coated with STELLITE

Explanation of symbols:

for metallic materials:0 = practically resistant, removal up to 2,4.g/ m2/day1 = fairly resistant, removal 2,4.–.24.g/m2/day2 = hardly resistant, removal 24.–.72.g/ m2/day3 = not resistant, removal over 72.g/m2//day– = not tested or not common

for sealing material:• = suitable– = not suitable

Abbreviations:Kp. = boiling pointsat. sol. = saturated solutionaq. Sol.. = aqueous solutionconc. = concentrated

Fluid Chemical formular ConcentrationAnd temperature

Materials for seals Metallic materials Material code

% °C

AF KFC

K-Fl

on

Met

all

EN-J

L10

40

StGP

240

GH

1.44

01/1

.440

8/1.

4571

HCnotecA 3COCH3 20 – • • • 0 0 0 allCnelytecA 2H2 • • • • III, VIII, X, Xc

Air, dry • • • • 0 0 0 allAlumAlum

KAI(SO4)2

KAI(SO4)2

1010

20100

••

••

••

••

––

––

00

X, XcX, Xc

Aluminium acetateAluminium ethylateAluminium chlorateAluminium fluorideAluminium oxyde

(CH3COO)3AlAl(OC2H5)2

Al(CIO3)3

AIF3

Al2 O3

––••–

•••••

•••••

•••–•

30–00

30–00

00030

X, Xcalle

X, XcIII, VIII

alleAmmonium bicarbonateAmmonium chlorideAmmonium chlorideAmmonium chlorideAmmonium chlorideAmmonium diphosphateAmmonium carbonateAmmonium nitrateAmmonium sulphate

(NH4)HCO3

NH4CINH4CINH4CINH4CI

(NH2)2HPO4

(NH4)2CO3

NH4NO3

(NH4)2SO4

5101050

2020

10020

Kp2020

–•–––––––

•••••••••

•••••••••

•••••••••

011311223

011311223

000000000

III, VIII, X, Xcallall

X, Xcall

III, VIII, X, XcX, XcX, XcX, Xc

Ammonium hydroxydeAmmonium hydroxyde

NH4 OHNH4OH

1010

20100

••

••

••

••

00

00

00

III, VIII, X, XcIII, VIII, X, Xc

CenilinA 6H5NH2 • • • • 0 0 0 allHdicacinesrA 3As04 • • • • 2 2 0 X, Xc

Asphalt (tar) • • • • – – 0 X, XcBeer • • • • 0 0 0 all

30

Fluid Chemical formular Concentrationand temperature


% °C

AF KFC

K-Fl

on

Met

all

EN-J

L10

40

StGP

240

GH

1.44

01/1

.440

8/1.

4571

CenezneB 6H6 – • • • 0 0 0 allBenzine • • • • 3 3 0 X, XcBleaching liquor (chloride of lime) • • • • – – 1 X, Xc

aNxaroB 2B407 10 H20 • • • • – – 0 X, XcBoric acidBoric acidBoric acid

H3BO3

H3BO3

H3BO3

44

100

20100100

•••

•••

•••

•••

222

222

000

X, XcX, XcX, Xc

CenatuB 4H10 • • • • 0 0 0 all2klimrettuB 0 • • • • – – 0 X, Xc

Butyl acetateButyl alcohol

CH3C00C4H9

C4H9OH––

••

••

••

00

00

00

allall

Calcium bisulphiteCalcium bisulphiteCalcium chlorideCalcium chlorideCalcium hydroxide (milk of lime)Calcium hypochloriteCalcium sulphate

Ca(HS 03)2

Ca(HS 03)2

CaCl2CaCl2

Ca(OH)2

Ca(CIO)2

CaSO4

2020020

100

•–••••–

•••••••

•••••••

•••••••

2212020

3312020

0001010

X, XcX, XcX, XcX, Xc

allX, Xc

allCarbon dioxyde, dryCarbon dioxyde, dry

CO2

CO2

bis 150400

––

•–

••

••

00

00

00

allVII, X, Xc

SCediflusidnobraC 2 20 – • • • 0 0 0 III, VIII, X, XclCCedirolhcartetnobraC 4 – • • • 1 1 0 all

ChloroformChloroformChlor sulphonic acid

CHCl3CHCl3

HOSO2Cl

Kp – • • • 1 1 3 all

Chromic acidChromic acidChromic acid

H2CroO4

H2CroO4

H2CroO4

101050

20Kp20

•••

••

•••

•••

1–0

0–0

000

III, VIII, X, XcX, Xc

III, VIII, X, XcCitric acid

Citric acid

(CH2COOH)2C(OH)COOH

CH2COOH)2C(OH)COOH

20

Kp

•

•

•

•

•

•

•

•

3

3

3

3

0

0

X, Xc

X, Xc

Clophen T 64 – • • • 0 0 0 allCopper acetate wat. sol.Copper acetate wat. sol

(CH3COOO)2Cu(CH3COOO)2Cu

20Kp

––

••

••

••

02

02

00

allX, Xc

Copper sulphateCopper sulphate

CuSO4

CuSO4

20Kp

••

••

••

••

33

22

00

X, XcX, Xc

Diazotation bath,(weakly acid)Diazotation bath,(weakly acid)

2080

––

••

••

••

22

22

11

X, XcX, Xc

2lioleseiD 0 • • • • 0 0 0 allDiphyl – • • • 0 0 0Dowtherm A – • • • 0 0 0 Dye liquor, alkaline or neutralDye liquor, alkaline or neutralDye liquor, organic acidDye liquor, organic acidDye liquor,weakly sulphuric acid

Dye liquor, strongly sulphuric acidDye liquor, strongly sulphuric acid

H2SO4 under0,3%

H2SO4 above 0,3%H2SO4 above 0,3%

20Kp20KpKp

20Kp

•••••

••

•••••

••

•••••

••

•••••

••

–––––

––

–––––

––

–0000

01

X, XcX, XcX, XcX, XcX, Xc

X, XcX, Xc

CenahtE 2H6 • • • • 0 0 0 allClonahtE 2H5OH • • • • 0 0 0 all

allall

31



% °C

AF KFC

K-Fl

on

Met

all

EN-J

L10

40

StGP

240

GH

1.44

01/1

.440

8/1.

4571

Ethyl etherEthyl acetateEthyleneEthylen chloride (Dichlorethan)

C2H5OC2H6

CH3COOC2H5

C2H4

(CH2Cl)2 20

Kp––•–

••••

••••

••••

1000

1000

0000

allallallall

Fatty acids from C6 – • • • 1 1 0 allFormaldehydeFormaldehyde

HCHOHCHO

4040

20Kp

••

••

••

••

33

33

00

X, XcX, Xc

Formic acidFormic acidFormic acidFormic acid

HCOOHHCOOHHCOOHHCOOH

1010

100100

2010020

100

––––

••••

••••

••••

3333

3333

0101


Freon – • • • 0 0 0 allGlacial acetic acidGlacial acetic acidGlacial acetic acidGlacial acetic acidGlacial acetic acidGlacial acetic acid

CH3COOHCH3COOHCH3COOHCH3COOHCH3COOHCH3COOH

101050508080

20Kp20Kp20Kp

––––––

••••••

••••••

••••••

223333

222222

000111

X, XcX, XcX, XcX, XcX, XcX, Xc

Glacial acetic acid CH3COOH 20 – • • • 2 2 0 X, XcGlycerineGlycerine

(CH2OH)2CHOH(CH2OH)2CHOH

20100

••

••

••

••

22

22

00

X, XcX, Xc

2rageniveparG 0 • • • • – – 0 X, XcHeat transfer oils – • • • 0 0 0Hydrochloric acid, dryHydrochloric acid, dry

HCIHCI

20100

––

••

••

••

11

11

12

allall

Hydrochloric acidHydrochloric acidHydrochloric acid

HCIHCIHCI

0,20,2

1

205020

•••

•••

•••

•••

333

333

011

X, XcX, XcX, Xc

HnegordyH 2 • • • • 0 0 0Hydrogen peroxideHydrogen peroxide

H2O2

H2O2

2050

––

••

••

••

33

33

00

X, XcX, Xc

Hydrogen sulphide, gas, dryHydrogen sulphide, gas,wet

H2SH2S

2020

––

••

• ••

––

––

00

X, XcX, Xc

Hydroxylamine sulphateHydroxylamine sulphate

(NH2OH)H2SO4

(NH2OH)H2SO4

1010

20Kp

••

••

••

••

––

––

00

X, XcX, Xc

Illuminating gas • • • • 0 0 0 allKreosoteKreosote

20Kp

––

••

••

••

––

––

00

X, XcX, Xc

Lead acetate (lead sugar)Lead arsenate

Pb(CH3C00)2

Pb(As04)2

100 Kp •–

••

••

••

3–

3–

20

X, XcX, Xc

Linseed oilLinseed oil

20100

••

••

••

••

––

––

00

X, XcX, Xc

Magnesium sulphateMagnesium sulphate

MgSO4

MgSO4

20Kp

••

••

••

••

11

11

00

allall

Manganous chlorideManganous chloride

MnCl2MnCl2

20Kp

––

••

••

••

22

22

00

X, XcX, Xc

MercuryMercury (II) chlorideMercury (II) nitrate

HgHgCl2

Hg(NO3)2

202020

••–

•••

•••

•••

133

133

000

III, VIII, X, XcX, XcX, Xc

Methyl alcoholMethyl alcoholMethylene chlorideMethylene chlorideM.E.K (Butanone)

CH3OHCH3OHCH2Cl2CH2Cl2

CH3COC2H5

20Kp20KpKp

••

••

••

••

allall

all

all

32



% °C

AF KFC

K-Fl

on

Met

all

EN-J

L10

40

StGP

240

GH

1.44

01/1

.440

8/1.

4571

Milk of limeMilk of lime

Ca(OH)2

Ca(OH)2

20Kp

––

••

••

••

00

00

00

allall

Milk • • • • 2 2 0 X, XcNatrium acetate CH3COONa 20 20 – • • • 1 1 0 allNatural gas • • • • 1 0 0 allNitric acidNitric acidNitric acidNitric acidNitric acidNitric acid

HNO3

HNO3

HNO3

HNO3

HNO3

HNO3

10104040

konz.konz.

20Kp20Kp20Kp

••••••

••••••

•••

•

••••••

333333

333332

000001


NnegortiN 2 • • • • 0 0 0 allOils (lubricating oils, mineral)Oils (vegetable)

2020

••

••

••

••

00

00

00

allall

CdicacielO 17H33COOH • • • • 0 0 0 allHOOCHOOCdicacilaxO • • • • 2 2 8 X, Xc0negyxO 2 20 • • • • 0 0 0 all

Penthyl acetate CH3COOC5H11 – • • • 0 0 0 all02rehtemuelorteP – • • • 0 0 0 all

ClonehP 6H5OH • • • • 2 2 0 X, XcPhosphoric acidPhosphoric acidPhosphoric acidPhosphoric acidPhosphoric acidPhosphoric acid

H3PO4

H3PO4

H3PO4

H3PO4

H3PO4

H3PO4

101050508080

20Kp20Kp20Kp

••••••

••••••

••••••

••••••

232333

232333

000102


Potassium acetatePotassium dichromatePotassium dichromatePotassium hydrogenartrate

Potassium hydrogenartrate (at 100°,sat.sol.)

CH3COOKK2Cr2O7

K2Cr2O7

COOH(CHOH)2COOK

COOH(CHOH)2COOK

25Kp20Kp20

Kp

–•••

•

••••

•

••••

•

••••

•

002–

–

002–

–

0000

1

allall

X, XCX, Xc

X, Xc

Potassium carbonatePotassium carbonate (potash)Potassium chlorate(at 100°, sat.sol.)

K2CO3

K2CO3

KCIO3

50 20KpKp

•••

•••

•••

•••

112

002

000

allall

X, Xc

Potassium chromium sulphatePotassium chromium sulphate(chromic alum)Potassium hydroxydePotassium hydroxydePotassium hydroxydePotassium hydroxydePotassium hydrochloritePotassium hydrochlorite up to 20.gakt. Cl2/l

KCr(SO4)212H2OKCr(SO4)212H2O

KOHKOHKOHKOH

KOCIKOCI

25255050

20Kp

20Kp20Kp2040

••

••••

–

••

••••••

••

••••••

••

••••••

––

0–0322

––

0–0322

03

000011

X, Xc

allX, Xc

allX, XcX, XcX. Xc

Xc

Potassium iodidePotassium iodidePotassium nitratePotassium nitratePotassium permanganatePotassium permanganate

KJKJ

KNO3

KNO3

KMnO4

KMnO4

Kp

20Kp20Kp

––•••

••

••

••

210203

210203

000000

III, VIII, X, Xc

allX, Xc

allX, Xc

Potassium cyanide solution KCN 5 20 • • • 1 1 0 III, VIII, X, XcCenaporP 3H8 20 • • • • 0 0 0 all

–

–

•

–

33



% °C

AF KFC

K-Fl

on

Met

all

EN-J

L10

40

StGP

240

GH

1.44

01/1

.440

8/1.

4571

Salicylic acid C6H4OHCOOH 20 – • • • 2 2 0 X, XcSalpeter • • • • 0 0 0 allSea waterSea water

20Kp

••

••

••

••

33

33

00

X, XcX, Xc

Silicone oil • • • • 0 0 0 allSoap • • • • 0 0 0 allSodium carbonateSodium carbonate

Na2CO3

Na2CO3

20Kp

••

••

••

••

01

01

00

allall

Sodium hydroxideSodium hydroxideSodium hydroxideSodium hydroxide

NaOHNaOHNaOHNaOH

203535

Kp20Kp

••••

••••

••••

••••

0–03

0–03

0000

allX, Xc

allX, Xc

aNetahplusmuidoS 2SO4 • • • • 0 0 0 all2lCaNeloS 0 • • • • 3 3 1 X, Xc

Spinbath (up to 10% H2SO4 •••08) • 3 3 0 X, XcStarch solution • • • • 2 2 0 X, Xc

•••)ruopavretaw(maetS • 0 0 0 all

CdicaciraetS 17H35 COOH • • • • 2 2 0 X, XcSugarSugar

2080

••

••

••

••

11

11

00

allall

Sulphite lye (fresh cooking liquor,spent liquor)Sulphite lye (fresh cooking liquor,spent liquor)

Ca(HSO3)2

Ca(HSO3)2

20

80

–

–

•

•

•

•

•

•

–

–

–

–

0

0

X, Xc

X, Xc

Sulphur dioxideSulphurous acid (cold) sat.sol.Sulfphuric acidSulfphuric acidSulfphuric acidSulfphuric acid

SO2

H2SO3

H2SO4

H2SO4

H2SO4

H2SO4

11090

konz.

20202020

••••••

••••••

•••••

••••••

333310

333310

000000


allTannic acidTannic acidTannic acid

C76H52O46

C76H52O46

C76H52O46

101050

20Kp20

•••

•••

•••

•••

232

232

000

X, XcX, XcX, Xc

081)lartuen(raT – • • • 1 1 0 III, VII, X, XcTartaric acid (CHOHCOOH)2 20 • • • • 2 2 0 X, Xc

ClouloT 6H5CH3 20 – • • • 0 0 0 allCenelyhterolhcirT 2HCI3 – • • • 1 1 0 all

02lioenitnepruT – • • • 0 0 0 allHN(aerU 2)2CO 20 • • • • 1 1 0 all

Water (fresh-a.drinking water)Water vapour <.140 °CWater vapour >.140 °CWater glass (K- and Na-silicate)

H2O

K2SiO3Na2HCI3

•••–

••••

••••

••••

0000

0000

0000

allVII, VIIIVII, VIII

allCenelyX 6H4(CH3)2 20 – • • • 0 0 0 all

•

34

KHI ball valves in district heating system KHI ball valves in district heating system

14.9 m in diameter is one of the big- gest drills in the world, that is used to build the largest railway tunnel in the Netherlands. In this application

KLINGER Ballostar ball valves areapplied for Betonit injection and forthe transport of mud. Our productsmeet the highest requested require-ments under difficult conditions.

35

Installation of KLINGER Ballostar KHSVI in the North of Poland

Final expection (pressure testing) of a KLINGER Ballostar KHSVI ball valve

acc. to DIN 3230

Application example: Valves for oxygen in steel mills

Oxygen requires high demands for allcomponents of a plant. Therefore all partsmust be without any traces of oil or fatat any time in order to avoid self-in-flammation.

KLINGER Ballostar ball KHI and KHA ball valves (for oxygen acc. to KLN 840) consis-ting of both steel casting and stainlesssteel, are famous for their high safety andthe small space that is needed for installation.

KHI DN 400 equipped with pneumatic actuator

Installation site of Stadtwerke Kiel (Kiel’s municipal utility): Klinger Ballostar KHSVI and Monoball ball valves

Product range Ballostar® KHA3-piece ball valve made ofgrey cast iron, steel and stainlesssteel

Ballostar® KHI2-piece ball valve with trunnionmounted ball, made of cast steel, steeland stainless steel

Ballostar® KHE2-piece ball valve with floating ball,made of steel and stainless steel

Monolith KHOOne-piece fully welded ball valvemade of steel

KLINGER Monoball®

One-piece ball valve made of steeland stainless steel

KLINGER Ball-o-topBrass ball valves

Piston valves KVNmade of grey cast iron, spheroidalcast iron, steel and stainless cast steel

KLINGERMATIC®

Actuator for piston valves and ballvalves

Circular sight-glasses

AB cocksPacking-sleeve cocks and pressure-gauge cocks in brass, steel and stain-less steel

KLINGER Fluid Control GmbHA-2352 Gumpoldskirchen, AustriaAm Kanal 8-10 . .Tel. +.43 (0)2252-600-0Fax +.43 (0)2252-600-359e-mail: [email protected]

Reflex- and transparent glasses

Documents

Ballostar KHI eng PRINT...8 Component test acc. to EN 488 – KHSVI 300/250 fully welded FFI-Hannover 9 Determination of flow resistance KHSVI 300/250 weld ends Arsenal Research 10