Balflex Hydraulic Hoses - Deutsche Messe AGdonar.messe.de/exhibitor/hannovermesse/2017/S... · Balflex Hydraulic Hoses Balflex® Hydraulic Hoses Balflex® hydraulic hoses are produced

Balflex Hydraulic Hoses

Balflex® Hydraulic Hoses

Balflex® hydraulic hoses are produced to Balflex

® specifications and according to ISO 1436, ISO 3869, ISO 3949,

SAE J517 and EN 853 to EN 857 standards. They cover a wide variety of low to very high pressure applications, in rubber, thermoplastic or P.T.F.E, with textile and steel reinforcement, for petroleum and water base hydraulic fluids.

Balflex® optimised the production of these hoses and their compatibility with a wide range of connectors, in order to

assure the highest performance and the most extensive range of applications. The Balflex

® hydraulic hose program includes:

> Textile Braid Hydraulic Hoses > Wire Braid Hydraulic Hoses > 4 and 6 Spiral Hydraulic Hoses > Thermoplastic Hoses General Guidelines Balflex

® hydraulic hoses are designed with a safety factor of 4: 1 relating minimum burst pressure and recommended

working pressure (except 2-MAX hose which is 2.3: 1). Working pressure and nominal diameter are always branded on the hose, except on hoses with external steel braid. Hydraulic hoses are designed for petroleum base hydraulic fluids applications with a temperature range of – 40ºC (- 40ºF) to + 100ºC (+ 212ºF). Special rubber compounds and other lining materials allow to exceed these limits. Hydraulic hoses may also be used for water base hydraulic fluids if the working temperature does not exceed + 70ºC (+ 158ºF). With the presence of air in the fluid working temperature should be reduced to + 60ºC (+ 140ºF).

Selection, assembly and installation of hydraulic hoses should follow Balflex

® recommendations and SAE J1273 and

DIN 20066 standards. Hydraulic hose assemblies should always be inspected and hydraulically tested before installation. All hydraulics systems should be tested against leakage and malfunction in an appropriate area after any intervention. Installations that do not comply with an adequate geometry of the hose assembly may reduce significantly the lifetime of the hose. Likewise, the use of wrongly dimensioned hoses or application in a system where working characteristics exceed the hose specifications may shorten drastically the hose lifetime. The failure of an hydraulic hose assembly may be dangerous and expose people and property to irreversible damage. Among other occurrences that must be prevented are the high velocity and high temperature projections of hydraulic fluid, the projection of couplings and it’s parts, the whipping of unrestrained hose, spillage of combustion of the fluid, electrical shocks through contact with electrical sources, immovability, fall or sudden movement of masses controlled by the hydraulic system. Construction characteristics and dimensions may be changed at any time without prior notice.

The data contained herein is information purposes only and does not enlarge, amend or imply any warranty other than provided by the manufacturer with the product. Any use of the product not in conformance with the manufacturer’s instructions may be dangerous.

Only items in this catalogue are carried in stock. Some items are subjected to minimum quantities or sold only in multiples of standard quantities. Please refer to the price list or contact our commercial department.

Balflex® – The European Technology Balflex 2010 (I) HYDR-2010 - 21


Hydraulic Hose – General Safety Guidelines Maintenance technicians, fabricators, end-users and installers need to be aware of the potential safety hazards when handling or even when in proximity to hydraulic hose assemblies. The following conditions can lead to personal injury and property damage: 1) Always use hose in well-ventilated areas; some fluids may permeate the hose cover and create fume and/or fire hazards. 2) Hydraulic systems typically operate at very high pressures. Any leak of pressurized fluid can penetrate the skin, causing severe tissue damage and burns. One good approach is to use guards or shields around the hose assembly to reduce the risk of injury. 3) Whipping – under high operating pressures, the hose and/or fitting can come loose or blow, causing the end of the hose to whip with great force. Again, the hose assembly should be shielded, guarded and, whenever possible, secured to avoid injury or damage from whipping. 4) Hydraulic fluids are flammable and can explode with a source of ignition. To avoid possible injury or property damage, care should be taken to eliminate ignition sources and to properly route the hose assembly to minimize the chance of combustion. 5) Most hose is conductive. Some applications require use of non-conductive hose to avoid electrocution. 6) When hydraulic hose assemblies fail, the equipment it powers will fail, too, sometimes abruptly and without warning. Never work directly beneath hydraulically powered booms, shovels or other large, heavy pieces of equipment. 7) When air or gaseous materials are being conveyed, the correct hose should be used. A pin-perforated cover may be required. Perforations in the cover will prevent permeated gases from accumulating and blistering the cover. Check with your supplier for the correct hose specification. 8) Extreme care should be used when operating hand-held hydraulic tools where the operator is in proximity to the hydraulic hose assembly. The following steps should be taken to avoid injury: a. Use strain relievers on each end of the hose to prevent kinking, excessive bending or stress on the hose at the coupling. b. Never use the hose assembly to pull or carry the tool. c. Exposed hose near the operator should be guarded in case hose assembly fails to prevent injury from high pressure or high temperature fluid. d. Operators should be protected with the required safety clothing for the job and fluids being used. e. The hose should be protected against any external damage. 9) Hose assemblies should be properly routed to avoid strain and the possibility of the hose bursting. Proper routing will also protect the assembly against flex fatigue, excessive heat or abrasion. 10) When selecting a hose style and assembly, check for hose compliance to all relevant government, industry, and safety standards or regulations. Construction characteristics and dimensions may be changed at any time without prior notice.



Balflex® – The European Technology (I) HYDR-2010 - 22 Balflex 2010


HIGH-PRESSURE INJECTION HAZARDS

High-pressure injection injuries (also known as grease gun injuries), are caused by the accidental injection of a foreign material, such as grease, oil, or solvent under pressure, through the skin and into the underlying tissue. This is analogous to medical techniques used to administer immunization shots without a needle.

A grease gun injury can cause serious delayed soft tissue damage and should be treated as a surgical emergency.

Any person sustaining an injury of this sort should seek immediate medical attention, regardless of the appearance of the wound or its size.

Accidents involving injection injuries can occur when using any type of pressurized equipment. Two common cases

in which petroleum products may be involved are accidents with pressurized grease guns or with hydraulic systems. Pressurized grease guns are commonly used in service stations, garages and industrial plants. Typically, most

service stations have grease guns operating at 500-1.000 kPa (90-150 psi) air pressure. Most modern industrial hydraulic systems operate in the range of 13 to 35 MPa (2,000 to 5,000 psi). A stream of oil ejected from a nozzle or leak under pressure of this magnitude has a velocity comparable to the muzzle velocity of a rifle bullet.

The most common sites of injury are the fingers or hand. However, any part of the body can be involved. With

grease guns, especially, accidents usually occur when the injured person wipes the tip of the nozzle with his finger or the nozzle slips off the grease fitting while being held in place.

Grease may also be injected into the body from a leak in the grease line. In hydraulic system accidents, a leak in

a hydraulic line can emit a high-velocity stream of oil and cause injury if it strikes a person. Workers are commonly injured when they try to stop the leak by covering it with their hand or finger.

Chemical irritation is not a major problem with most petroleum products because hydraulic oils and greases are

generally non-irritating and low toxicity to skin. However, the resulting bacterial infection can be a problem because of the damaged tissue and circulation in the wound, even though it has been surgically opened and the foreign material removed. One of the dangers from this type of injury is that it is not recognized quickly by the injured person as being serious. Often the initial wound may be very small and essentially painless. The injured person may even continue working. However, in every case in which a person receives this type of injury, he or she should stop work and get immediate medical treatment.

The following are some basic rules that must be observed: DON’T

Play around with or use a grease gun for practical jokes; Touch the end of a grease gun; Use any part of the body to test a grease gun for grease flow; Use any part of the body to stop a leak in a hydraulic line. DO Routinely check all hoses for wear and possible weak spots; Handle a grease gun with respect for its power; Take special care when starting up a new hydraulic system to be sure that every part of the system can

withstand the operating pressure. IN CASE OF A GREASE GUN ACCIDENT, SEEK IMMEDIATE MEDICAL TREATMENT. Identify the grease or oil involved in the accident. Contact the supplier or the manufacturer to obtain the product’s Material Safety Data Sheet (MSDS) about possible toxicity if a physician or hospital needs more information. Construction characteristics and dimensions may be changed at any time without prior notice.





HYDRAULIC HOSE AND ELECTROCUTION

Although it is a mercifully infrequent occurrence, workers have been burned or electrocuted when using metal-reinforced hoses on aerial bucket trucks near energized power lines. Hydraulic hose, fluid and power lines are a deadly combination. Electrical contact between two power line phases through a metal-reinforced hydraulic hose can generate sufficient heat to rupture the hose and cause a fire. In addition, an electrocution hazard can be created if a metal-reinforced hose on the boom of a truck contacts an energized power line and allows current to flow through the truck chassis. Either scenario can quickly result in serious injury or death.

OSHA standards require that all hydraulic tools used on or near energized power lines or equipment be supplied

with non-conducting hoses with sufficient strength for normal operating pressures. NIOSH recommends that the following precautions be taken to control the hazards associated with hydraulic hoses used on aerial bucket trucks:

Employers should not install metal-reinforced hydraulic hoses on any part of the boom, aerial bucket or hydraulic attachments of aerial bucket trucks used near energized power lines;

Employers should remove any metal-reinforced hoses currently installed on any part of the boom, aerial bucket or hydraulic attachments of aerial bucket trucks used to work near energized power lines. Before work begins, employers should require a competent person to conduct an initial and daily job site survey and inspect all equipment to identify hazards and implement appropriate controls;

Employers should stress the importance of adherence to established safe work procedures. These include covering energized power lines in the immediate work area with insulating hoses or blankets, or de-energizing and grounding the lines before work begins. Workers should test de-energized power lines to verify that they have actually been de-energized;

Employers should provide all workers with task-specific training that shows how each step controls the identified hazard;

Employers should install all hydraulic hoses used in aerial buckets so that the flow of hydraulic fluid can be stopped immediately by the worker in the bucket. This objective can be achieved by incorporating a control valve into the hydraulic system in the aerial bucket. Manufacturers should continue research into the development of hydraulic fluids that are non-flammable and non-conducting.

Employers should encourage equipment and tool manufacturers to design an independent coupling system to prevent the use of unsuitable hydraulic hoses on booms, aerial buckets or aerial bucket attachments. Labelling or colour coding hoses may also help workers who service this equipment.

These Guidelines reflect common practice procedures to be held for a Safe use of Hydraulic Fluid Power. In no event shall Balflex

® have any liability whatsoever to any person for any special, punitive,

incidental or consequential damages been caused by mishandling of Hydraulic Fluid Power systems.

Construction characteristics and dimensions may be changed at any time without prior notice.





Cross-reference for Hydraulic Hoses

Showing Balflex hose type with corresponding competitor’s hose type

Balflex

Hydraulic Hose

10 Serie type

R6 1TE

1216

R3 3TE

1220

R1AT 1SN

1002

R2AT 2SN

1004

R17

1017

R5

1007

R12

1012

4SP

1008

4SH

1009

R13

1014

R15

1016

Aeroquip Eaton

2583

GH663

GH793

FC639

1503 GH493 FC659

GH506 FC254

FC606

Dayco A6 D1 MX BXX D6 Y9 M7/CZ N3 NH/N6 N2 Gates C6 C3 C1T C2AT M3K C5C C12 C13 G6K GoodYear 9060 9015 9025 9291 9050 9120 9130 Imperial Eastman

E7

J4 HR1C HFS

Y9A M6 M7

N5 N6

Parker

7517

601 422 481

381

451TC 201 261

77C

701

731 78C 792

791

Weatherhead H009 H017 H104 H425 H300 H066 H430 H470

Balflex

Hydraulic Hose

10 Serie type

R4

1219

R7

1030

R7 NON CONDUCTIVE

1030L

R8

1032

PREMIUM 2SC – R16

1019

2-MAX JACK

1029

R14 BALFLON

2000 / 3

Aeroquip Eaton

FC318 FC619

FC372

FC373

FC374

FC310

FC579

2807

Dayco C S7 S7E S8 TS Gates GMV C7S C7SNC C8S M2T J2AT C14 GoodYear 9040 9070 9075 9080 Imperial Eastman

HR7 D5A

HR70 D4A

HR8

T1

Parker 881 540N 510A / 518A 520N 431 JK 919 Weatherhead H039 H436 H435 H336 H243

The information provided by this Cross-reference chart is intended as a reference guide only. These hoses are similar but not exactly equal in all technical data and performances. Refer to hydraulic hose specifications to assure that the suggested hydraulic hose will attend the required application.






Table 1a: Nominal working pressure at 20ºC (+ 68ºF) of Balflex® hydraulic hoses MPa / PSI

3/16” - 3

1/4" - 4

5/16” - 5

3/8” - 6

1/2" - 8

5/8” - 10

3/4" - 12

1” - 16

1.1/4” - 20

1.1/2” - 24

2” - 32

Balflex®

Standards

2TE

ISO 4079 - 2

EN 854 2TE

_ 8.0 1160

_7.5 1087

6.8 985

6.3 913

5.8 840

5.0 725

4.5 650

4.0 580

R3 / 3TE

ISO 4079 - 3 EN 854 3TE SAE 100R3

16.0 2320

14.5 2100

13.0 1885

11.0 1595

_ 9.3 1350

_ 8.0 1160

_ 7.0 1015

5.5 797

4.5 650

(b)

4.0 580

(b)

3.3 480

R1T / 1SN

ISO 1436 EN 853 type 1 SAE 100R1

25.0 3625

22.5 3260

21.5 3115

18.0 2610

16.0 2320

13.0 1885

10.5 1520

8.8 1275

6.3 910

5.0 725

4.0 580

R2T / 2SN

ISO 1436 EN 853 type 2 SAE 100R2

41.5 6015

40.0 5800

35.0 5075

33.0 4785

27.5 3985

25.0 3625

21.5 3120

16.5 2390

12.5 1810

_ 9.0 1300

_ 8.0 1160

BALPAC PREMIUM 2SC–R16

ISO 11237 EN 857 – 2SC SAE 100R16

40.0 5800

35.0 5075

33.0 4785

27.6 4000

25.0 3625

21.5 3118

16.5 2393

BALPAC 3000 R17

ISO 11237 EN 857 SAE 100R17

22.5 3260

21.0 3000

21.0 3000

21.0 3000

25.0 3625

21.5 3120

21.0 3000

R12

ISO 3862 EN 856 R12 SAE 100R12

27.6 4000

27.6 4000

27.6 4000

27.6 4000

27.6 4000

20.7 3000

17.2 2500

17.2 2500

4SP

ISO 3862 EN 856 4SP

50.0 7250

44.5 6453

41.5 6018

35.0 5075

35.0 5075

28.0 4060

21.0 3045

18.5 2683

16.5 2393

4SH

ISO 3862

EN 856 4SH

42.0 6090

38.0 5510

32.5 4713

29.0 4205

25.0 3625

R13

ISO 3862 EN 856 R13 SAE 100R13

42.0 6090

38.0 5510

34.5 5000

34.5 5000

34.5 5000

R15

ISO 3862

SAE 100R15

41.4 6000

41.4 6000

41.4 6000

41.4 6000

41.4 6000

41.4 6000

2-MAX JACK

a)

_ 70.0 10000

_ 70.0 10000

_ 55.2

8000

3-MAX

a)

50.0 7200

47.0 6800

a) according to Balflex® specifications

b) not included in the standards






Table 1b: Nominal working pressure at 20ºC (+ 68ºF) of Balflex

® hydraulic hoses MPa / PSI

3/16” - 4

1/4" - 5

5/16” - 6

13/32” - 8

1/2" - 10

5/8” - 12

7/8" - 16

1.1/8” - 20

1.3/8” - 24

1.13/16” - 32

2.3/8” - 40

3” - 48

Balflex®

Standards

R5

SAE 100R5 SAE J1402 AII

20.7 3000

20.7 3000

15.5 2250

13.8 2000

12.1 1755

10.3 1495

5.5 800

4.3 625

3.4 500

2.4 350

2.4 350

1.4 200

Table 1c: Nominal working pressure at 20ºC (+ 68ºF) of Balflex

® hydraulic hoses MPa / PSI

1/8” - 2

3/16” - 3

1/4" - 4

5/16” - 5

3/8” - 6

1/2" - 8

5/8” - 10

3/4" - 12

1” - 16

Balflex®

Standards

R7

ISO 3949 EN 855 R7 SAE 100R7

(b)

28.0 4060

21.0 3045

19.0 2755

19.0 2755

16.0 2320

14.0 2030

10.5 1523

9.0 1305

7.0 1015

R7 NON CONDUCTIVE

ISO 3949 EN 855 R7 SAE 100R7

(b)

28.0 4060

21.0 3045

19.0 2755

19.0 2755

16.0 2320

14.0 2030

10.5 1523

9.0 1305

7.0 1015

R7 STEELFLEX

a)

35.0 5075

30.0 4350

27.5 3988

24.0 3480

22.0 3190

17.5 2538

14.0 2030

11.5 1668

10.0 1450

R8 (10.1032.)

ISO 3949 EN 855 R8 SAE 100R8

35.0 5075

35.0 5075

29.0 4205

28.0 4060

24.5 3553

19.0 2755

15.5 2250

14.0 2030

R8 (10.1033.)

ISO 3949 EN 855 R8 SAE 100R8

35.0 5075

35.0 5075

30.0 4350

28.0 4060

24.5 3553

20.0 2900

16.5 2393

14.0 2030

ULTRAFLEX R9

a)

38.0 5510

34.5 5000

a) according to Balflex® specifications

b) not included in the standards

Table 1d: Nominal working pressure at 20ºC (+ 68ºF) of Balflex® hydraulic hoses MPa / PSI

3/16” - 3

1/4" - 4

5/16” - 5

3/8” - 6

1/2" - 8

5/8” - 10

3/4" - 12

7/8" - 14

1” - 16

Balflex®

Standards

R6 / 1TE

ISO 4079 - 1 EN 854 1TE SAE 100R6

3.4 500

2.8 400

2.8 400

2.8 400

2.8 400

2.4 350

2.1 300

2.2 310

1.7 250






Table 2: Pressure Conversion

bar

0,00134

0,0025

0,0339

0,069

0,098

1,00

1,01

10,0

100

PSI

0,0194

0,036

0,492

1,001

1,421

14,504

14,69

145,04

1450,38

MPa

-

-

0,003

0,007

0,0098

0,10

0,101

1,00

10,00

1 atm

0,001

0,0025

0,0335

0,068

0,097

0,987

1,00

9,87

98,69

m H20 (20ºC)

0,014

0,026

0,346

0,704

1,000

10,207

10,34

102,074

1020,736

in Hg (20ºC)

0,0396

0,074

1,001

2,04

2,89

29,53

29,91

295,30

2953

in H20 (20ºC)

0,538

1,005

13,623

27,73

39,38

401,86

407,09

4018,65

40186,47

mm Hg (20ºC)

1,005

1,88

25,43

51,75

73,51

750,06

759,81

7500,62

75006,17

Example: 1 MPa = 14,51 PSI ; 1Mpa = 10,0bar

Table 3: Conversion Factors

Unit

Factor

Converted Unit

1 m (meter)

1000

mm (millimeter)

1 m (meter)

1,09362

yard

1 m (meter)

3,28084

foot

1 mm (millimeter)

0,001

m (meter)

1 mm (millimeter)

0,03937

Inch

1 inch

25,4

mm (millimeter)

1 inch

0,0254

m (meter)

1 foot

0,3048

m (meter)

1 yard

0,9144

m (meter)

F

C x 1,8 + 32

F (Fahrenheit)

C

(F - 32): 1,8

C (Celsius)

Example: 1 m = 3,28084 feet ; 1 inch = 25,4mm Example: + 100ºC = + 212ºF Construction characteristics and dimensions may be changed at any time without prior notice.





Selection of hydraulic hoses

Working pressure:

When selecting a hose it should be considered that it’s working pressure should be higher than the maximum operating pressure of the system. For determination of the maximum operating pressure the system engineer should always consider possible pressure peaks during start up and inversion. Pressure peaks may be so short that they are only measurable with electronic devices. In suction applications, the capacity of the hose to withstand negative pressure is a decisive factor. Working pressures are given for working temperature of + 20ºC (+ 68ºF). For increased temperatures a de-rating factor should be considered. The rated working pressures of Balflex

® hydraulic hoses are

summarized in table 1.

Note: Only an accurate knowledge of the pressure history of the service cycles of the equipment should lead to a sub-dimensioning of the hose by the engineer, bearing in mind the recommendations of SAE J 1927 standards. Temperature:

Excessive temperature is one of the main limitations of rubber and induces accelerated aging. Fluid temperature, either in motion or with the equipment stopped, should not exceed the maximum working temperature recommended for each hose. Likewise, surrounding temperature should be considered, specially when resulting from heat sources in the proximity of the hose assembly. Fluid compatibility:

Fluid compatibility with the hose and the coupling should be verified. Fluids that chemically attack the hose can lead to the contamination and obstruction of the hydraulic system and to premature failure of the hose. Handling gases requires special attention. As an orientation, the Balflex

® Hydraulic Hose Fluid Compatibility Chart gives a

classification of compatibility with some fluids. Consult Balflex® for compatibility of other fluids and rubber

compounds. Whenever in doubt test before application.

Dimensioning:

Dimensioning of all components should guarantee that pressure loss is kept at a minimum, in order not to reduce power transmission and to avoid overheating or turbulence of the fluid that might lead to deterioration of the lining. Assembly geometry:

Installation should guarantee that the minimum bend radius of the hose is respected and that bending occurs only in one plane. Hose length may suffer a variation between – 4% and + 2%, when submitted to pressure. The assembly length should provide enough margin for this change in length. Torsion and traction of the assembly must be avoided and protection and restrain of the assembly should be considered if there are obstacles to avoid. Mechanical loads acting on the assembly, including vibration, should be kept at a minimum. Free swivelling connectors should be used whenever torsion is present. Whenever hose failure may result in whipping (for example in gas applications) restraint through a steel cable to the connecting parts should be considered. When connecting a moving part, the free movement of the assembly without touching any surface should be assured. Positioning of the assembly should consider that risks of bodily injure and equipment damage through spillage or fluid ejection are minimized. Table 4 shows some correct and incorrect installation situations. Environmental compatibility:

The hose and couplings compatibility with the working environment factors, as temperature, fire hazard, UV light, ozone, chemicals and electrical charges should be considered. External protection sleeves require an adequate assembly. Air and Gaseous applications:

Hose assemblies that are to be used in air and other gaseous applications shoud be pin-pricked, through the cover, prior to use. These micro perforations allow gas that has permeated the inner tube of the hose to escape into the atmosphere. This prevents gases from accumulating and blistering the hose cover. Construction characteristics and dimensions may be changed at any time without prior notice.





Electrical conductivity:

Electrical conductivity, to avoid static electricity build up, or non-conductivity, to avoid electrical discharge through the assembly, may be decisive requirement to avoid explosion or electrical shocks. Whenever the hose is not unequivocally branded either non-conductive or anti-static, its electrical characteristics should always be considered as not controlled. Permeability:

All hoses present a certain degree of permeability, especially with gases and highly volatile liquids. The designer should consider the possibility that this permeability results in system or environment contamination. Abrasion:

Accelerated external abrasion, through contact in motion or exposure to projected particles reduces drastically hose life and leads to premature failure through exposure of the reinforcement. For special applications Balflex

®

recommends hoses with special abrasion resistant rubber compounds or protection through adequate sleeves. Couplings selection:

Couplings are a fundamental part of the geometry of hose assemblies. The compatibility of sealing and securement of the couplings to the system ports should be verified. The recommended coupling series for each hose should be used and the assembly instructions carefully followed. Inadequate couplings may damage the hose and lead to a premature failure.

Table 4: Examples of installation of hoses assemblies

Incorrect Correct Incorrect Correct

Incorrect Correct Incorrect Correct

Incorrect Correct






Balflex® Hose Selection Chart

This graphic helps finding the Nominal Hose Diameter-DN (mm) or the Dash Size. Firstly, one must know the Flow Rate and Fluid Velocity values that are being used. These two pieces of information must be found in the outer graphic lines. Then by linking these two values with a straight line, one should obtain the Nominal Hose Diameter-DN (mm) or the Gauge Diameter-A (cm²). The example below shows that for a fluid velocity of 4 meters per second and a flow rate of 70 liters per minute or 19 gallons per minute, one should choose a hose with DN of 19mm it means 3/4" hose or a dash hose -12.





Balflex DIN 1TE / SAE 100R6 – DIN 2TE

Balflex® DIN EN 854 1TE / SAE 100R6 – 10.1216.

According to ISO 4079 type 1 / DIN EN 854 type 1TE / SAE J517 type SAE 100R6

Medium pressure, single textile braid reinforced hydraulic hose

Inner tube: Reinforcement:

Outer tube: Safety factor:

Application: Temperature range:

Couplings:

seamless oil resistant synthetic rubber 1 high resistance synthetic fiber braid black, oil, weather and abrasion resistant synthetic rubber 4: 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF) Max. temperature recommended for water base hydraulic fluids: + 70ºC (+ 158ºF) Max. temperature recommended for air: + 50ºC (+ 122ºF) Balflex

® crimped fittings 23 serie with ferrules 20.107. serie

part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight

mm inch mm inch MPa PSI MPa PSI mm inch kg/m

10.1216.03 3/16” - 3 4,8 0.19 11,1 0.44 3.4 500 13.8 2000 51 2.0 0,10 10.1216.04 1/4" - 4 6,3 0.25 12,5 0.49 2.8 400 11.0 1600 64 2.5 0,12 10.1216.05 5/16” - 5 8,0 0.31 14,0 0.55 2.8 400 11.0 1600 76 3.0 0,15 10.1216.06 3/8” - 6 9,5 0.38 16,0 0.63 2.8 400 11.0 1600 76 3.0 0,16 10.1216.08 1/2" - 8 12,7 0.50 19,8 0.78 2.8 400 11.0 1600 102 4.0 0,24 10.1216.10 5/8” - 10 16,0 0.63 23,0 0.91 2.4 350 9.7 1400 127 5.0 0,28 10.1216.12 3/4" - 12 19,0 0.75 26,2 1.03 2.1 300 8.3 1200 152 7.0 0,41 10.1216.14 7/8’ - 14 22,0 0.87 31,3 1.23 2.2 310 8.8 1240 200 7.9 0,56 10.1216.16 1” - 16 25,4 1.00 32,5 1.28 1.7 250 6.8 1000 203 8.0 0,58

Note: Sizes - 14 (DN 22) 7/8” and - 16 (DN 25) 1” not included in the standards.

COVER: U.S. MSHA APPROVED

Balflex® DIN EN 854 2TE – 10.1217.

According to ISO 4079 type 2 / DIN EN 854 type 2TE

Medium pressure, single textile braid reinforced hydraulic hose

part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1217.03 3/16” - 3 4,8 0.19 11,8 0.46 8.0 1160 32.0 4640 25 1.0 0,11 10.1217.04 1/4" - 4 6,3 0.25 13,4 0.53 7.5 1087 30.0 4350 40 1.5 0,13 10.1217.05 5/16” - 5 8,0 0.31 14,9 0.59 6.8 985 27.2 3940 50 2.0 0,17 10.1217.06 3/8” - 6 9,5 0.38 16,5 0.65 6.3 913 25.2 3650 60 2.4 0,18 10.1217.08 1/2" - 8 12,7 0.50 19,7 0.78 5.8 840 23.2 3360 70 2.8 0,26 10.1217.10 5/8” - 10 16,0 0.63 23,9 0.94 5.0 725 20.0 2900 90 3.6 0,30 10.1217.12 3/4" - 12 19,0 0.75 27,0 1.06 4.5 650 18.0 2610 110 4.4 0,43 10.1217.16 1” - 16 25,4 1.00 34,4 1.35 4.0 580 16.0 2320 150 5.9 0,60

COVER: U.S. MSHA APPROVED Construction characteristics and dimensions may be changed at any time without prior notice.




Balflex DIN EN 854 3TE / SAE 100R3

Balflex® DIN EN 854 3TE / SAE 100R3 – 10.1220.

According to ISO 4079 type 3 / DIN EN 854 type 3TE / SAE J517 type SAE 100R3

Medium pressure, double textile braid reinforced hydraulic hose




Couplings:

seamless oil resistant synthetic rubber 2 high resistance synthetic fiber braids black, oil, weather and abrasion resistant synthetic rubber 4: 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF). Max. temperature recommended for water base hydraulic fluids: + 70ºC (+ 158ºF) Max. temperature recommended for air: + 50ºC (+ 122ºF) Balflex

® crimped fittings 23 serie with ferrules 20.201. serie on sizes 1/4", 5/16”, 3/8”, 1”,

1.1/4”, 1.1/2” and 2”, and 20.202. series on sizes 1/2", 5/8” and 3/4".

part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1220.03 3/16” - 3 4,8 0.19 12,8 0.50 16.0 2320 64.0 9280 40 1.57 0,13 10.1220.04 1/4" - 4 6,3 0.25 14,5 0.57 14.5 2100 58.0 8400 45 1.77 0,18 10.1220.05 5/16” - 5 8,0 0.31 17,0 0.67 13.0 1885 52.0 7540 55 2.17 0,25 10.1220.06 3/8” - 6 9,5 0.38 18,5 0.73 11.0 1595 44.0 6380 70 2.76 0,28 10.1220.08 1/2" - 8 12,7 0.50 21,8 0.86 9.3 1350 37.2 5400 85 3.35 0,44 10.1220.10 5/8” - 10 16,0 0.63 26,0 1.02 8.0 1160 32.0 4640 105 4.13 0,49 10.1220.12 3/4" - 12 19,0 0.75 29,0 1.14 7.0 1015 28.0 4060 130 5.12 0,68 10.1220.16 1” - 16 25,4 1.00 36,0 1.42 5.5 797 22.0 3188 150 5.91 0,69 10.1220.20 1.1/4” - 20 32,0 1.25 42,0 1.65 4.5 650 18.0 2600 190 7.48 0,88 10.1220.24 1.1/2” - 24 38,0 1.50 49,5 1.95 4.0 580 16.0 2320 240 9.45 1,27 10.1220.32 2” - 32 50,8 2.00 62,2 2.45 3.3 480 13.2 1920 300 11.81 1,35

Note: Sizes - 24 (1.1/2”) and - 32 (2”) not included in the standards.






Balflex SAE 100R4

Balflex® SAE 100R4 – 10.1219.

According to SAE J517 type SAE 100R4

Suction & Delivery hydraulic hose

Inner tube:

Reinforcement: Outer tube:

Safety factor: Application:

Temperature range:

Couplings:

seamless oil resistant synthetic rubber textile braids and 1 high strength steel wire helix black, oil, weather and abrasion resistant synthetic rubber 4: 1 suction, delivery, return & discharge of petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF); Intermittent service: + 120ºC (+ 248ºF) Max. temperature recommended for water base hydraulic fluids: + 70ºC (+ 158ºF) Max. temperature recommended for air: + 60ºC (+ 140ºF) Balflex

® fittings 23 serie up to 2” and 44 serie from 3” up to 4” with clamps

part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1219.12 3/4" - 12 19,0 0.75 34,9 1.38 2.1 315 8.4 1260 127 5.0 0,75 10.1219.16 1” - 16 25,4 1.00 41,3 1.63 1.7 255 6.8 1020 152 6.0 0,93 10.1219.20 1.1/4” - 20 31,8 1.25 50,8 2.00 1.4 210 5.6 840 203 8.0 1,25 10.1219.24 1.1/2” - 24 38,1 1.50 57,2 2.25 1.05 157.5 4.2 630 254 10.0 1,54 10.1219.32 2” - 32 50,8 2.00 69,9 2.75 0.7 105 2.8 420 305 12.0 2,00 10.1219.40 2.1/2” - 40 63,5 2.50 82,6 3.25 0.4 60 1.6 240 356 14.0 2,50 10.1219.48 3” - 48 76,2 3.00 95,3 3.75 0.4 60 1.6 240 457 18.0 3,20 10.1219.56 3.1/2” - 56 88,9 3.50 108 4.25 0.3 45 1.2 180 533 21.0 4,03 10.1219.64 4” - 64 101,6 4.00 121 4.75 0.25 37.5 1.0 150 610 24.0 5,04





Balflex DIN EN 853 1SN / SAE 100R1AT

Balflex® DIN EN 853 1SN / SAE 100R1AT – 10.1002.

According to ISO 1436 / DIN EN 853 type 1SN / SAE J517 type SAE 100R1 AT

High pressure, single steel braid reinforced hydraulic hose

Inner tube:



Temperature range:

Couplings:

seamless oil resistant synthetic rubber 1 high tensile steel wire braid black, oil, weather and abrasion resistant synthetic rubber 4: 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF); Intermittent service: + 120ºC (+ 248ºF) Max. temperature recommended for water base hydraulic fluids: + 70ºC (+ 158ºF) Max. temperature recommended for air: + 60ºC (+ 140ºF) Balflex

® crimped fittings 23 serie with ferrules 20 serie. Multicrimp P23 serie

part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1002.03 3/16” - 3 4,8 0.19 11,8 0.47 25.0 3625 100.0 14500 89 3.5 0,23 10.1002.04 1/4" - 4 6,3 0.25 13,4 0.53 22.5 3260 90.0 13040 100 3.9 0,26 10.1002.05 5/16” - 5 8,0 0.31 15,0 0.59 21.5 3115 85.0 12460 114 4.5 0,30 10.1002.06 3/8” - 6 9,5 0.38 17,4 0.69 18.0 2610 72.0 10440 127 5.0 0,36 10.1002.08 1/2" - 8 12,7 0.50 20,7 0.81 16.0 2320 64.0 9280 178 7.0 0,46 10.1002.10 5/8” - 10 16,0 0.63 23,8 0.93 13.0 1885 52.0 7540 200 7.9 0,56 10.1002.12 3/4" - 12 19,0 0.75 27,8 1.09 10.5 1520 42.0 6080 240 9.4 0,74 10.1002.16 1” - 16 25,4 1.00 35,9 1.40 8.8 1275 35.0 5100 300 11.8 1,06 10.1002.20 1.1/4” - 20 32,0 1.25 43,8 1.71 6.3 910 25.0 3640 419 16.5 1,36 10.1002.24 1.1/2” - 24 38,0 1.50 51,1 1.99 5.0 725 20.0 2900 500 19.7 1,65 10.1002.32 2” - 32 50,8 2.00 64,5 2.52 4.0 580 16.0 2320 630 24.8 2,05 10.1002.40 2.1/2” - 40 63,5 2.50 79,0 3.11 5.0 725 20.0 2900 760 30.4 2,89 10.1002.48 3 “ - 48 76,2 3.00 92,0 3.62 3.5 508 14.0 2030 900 36.0 3,43


Balflex® hydraulic hose DIN EN 853 1SN / SAE 100R1AT has a very superior working and burst pressure compared

with only SAE 100R1AT







Balflex® DIN EN 853 2SN / SAE 100R2AT – 10.1004.


High pressure, double steel braid reinforced hydraulic hose

Inner tube:



Temperature range:

Couplings:

seamless oil resistant synthetic rubber 2 high tensile steel wire braids black, oil, weather and abrasion resistant synthetic rubber 4: 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF); Intermittent service: + 120ºC (+ 248ºF) Max. temperature recommended for water base hydraulic fluids: + 70ºC (+ 158ºF) Max. temperature recommended for air: + 60ºC (+ 140ºF) Balflex


part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1004.03 3/16” - 3 4,8 0.19 13,4 0.53 41.5 6015 165.0 24060 89 3.5 0,32 10.1004.04 1/4" - 4 6,3 0.25 15,0 0.59 40.0 5800 160.0 23200 100 3.9 0,38 10.1004.05 5/16” - 5 8,0 0.31 16,6 0.65 35.0 5075 140.0 20300 114 4.5 0,45 10.1004.06 3/8” - 6 9,5 0.38 19,0 0.75 33.0 4785 132.0 19140 127 5.0 0,53 10.1004.08 1/2" - 8 12,7 0.50 22,2 0.87 27.5 3985 110.0 15940 178 7.0 0,65 10.1004.10 5/8” - 10 16,0 0.63 25,5 1.00 25.0 3625 100.0 14500 200 7.9 0,76 10.1004.12 3/4" - 12 19,0 0.75 29,4 1.15 21.5 3120 86.0 12480 240 9.4 1,00 10.1004.16 1” - 16 25,4 1.00 37,9 1.50 16.5 2390 65.0 9560 300 11.8 1,48 10.1004.20 1.1/4” - 20 32,0 1.25 48,5 1.90 12.5 1810 50.0 7240 419 16.5 2,14 10.1004.24 1.1/2” - 24 38,0 1.50 54,7 2.15 9.0 1300 36.0 5200 500 19.7 2,55 10.1004.32 2” - 32 50,8 2.00 67,4 2.65 8.0 1160 32.0 4640 630 24.8 3,30 10.1004.40 2.1/2” - 40 63,5 2.50 83,0 3.27 7.0 1015 28.0 4060 760 30.4 3,96 10.1004.48 3 “ - 48 76,2 3.00 96,0 3.78 5.5 798 22.0 3192 900 36.0 4,96

Note: Size - 48 (3”) not included in the standards.








Balflex DIN EN 853 1ST / SAE 100R1A

Balflex® DIN EN 853 1ST / SAE 100R1A – 10.1001.

According to ISO 1436 / DIN EN 853 type 1ST / SAE J517 type SAE 100R1 A

THICK COVER - High pressure, single steel braid reinforced hydraulic hose

Inner tube:



Temperature range:

Couplings:

seamless oil resistant synthetic rubber 1 high tensile steel wire braid black, oil, weather and abrasion resistant synthetic rubber 4: 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF); Intermittent service: + 120ºC (+ 248ºF) Max. temperature recommended for water base hydraulic fluids: + 70ºC (+ 158ºF) Max. temperature recommended for air: + 60ºC (+ 140ºF) Balflex


part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1001.04 1/4" - 4 6,3 0.25 15,5 0.61 22.5 3260 90.0 13040 100 3.94 0,29 10.1001.05 5/16” - 5 8,0 0.31 17,1 0.67 21.5 3115 85.0 12460 115 4.53 0,34 10.1001.06 3/8” - 6 9,5 0.38 19,4 0.76 18.0 2610 72.0 10440 130 5.12 0,42 10.1001.08 1/2" - 8 12,7 0.50 22,6 0.89 16.0 2320 64.0 9280 180 7.09 0,51 10.1001.10 5/8” - 10 16,0 0.63 25,8 1.02 13.0 1885 52.0 7540 200 7.87 0,59 10.1001.12 3/4" - 12 19,0 0.75 29,8 1.17 10.5 1520 42.0 6080 240 9.45 0,73 10.1001.16 1” - 16 25,4 1.00 37,6 1.48 8.8 1275 35.0 5100 300 11.81 1,05 10.1001.20 1.1/4” - 20 32,0 1.25 45,0 1.77 6.3 910 25.0 3640 420 16.54 1,36 10.1001.24 1.1/2” - 24 38,0 1.50 51,4 2.02 5.0 725 20.0 2900 500 19.68 1,56 10.1001.32 2” - 32 50,8 2.00 66,4 2.61 4.0 580 16.0 2320 630 24.80 2,30

Note: usually not avaiable in stock, only by order.

Balflex

® hydraulic hose DIN EN 853 1ST / SAE 100R1A has a very superior working and burst pressure compared with only SAE 100R1A






Balflex® DIN EN 853 2ST / SAE 100R2A – 10.1003.


THICK COVER - High pressure, double steel braid reinforced hydraulic hose

Inner tube:



Temperature range:

Couplings:



part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1003.04 1/4" - 4 6,3 0.25 17,1 0.67 40.0 5800 160.0 23200 100 3.94 0,45 10.1003.05 5/16” - 5 8,0 0.31 18,7 0.74 35.0 5075 140.0 20300 115 4.53 0,52 10.1003.06 3/8” - 6 9,5 0.38 21,0 0.83 33.0 4785 132.0 19140 130 5.12 0,64 10.1003.08 1/2" - 8 12,7 0.50 24,2 0.95 27.5 3985 110.0 15940 180 7.09 0,75 10.1003.10 5/8” - 10 16,0 0.63 27,4 1.08 25.0 3625 100.0 14500 200 7.87 0,88 10.1003.12 3/4" - 12 19,0 0.75 31,4 1.24 21.5 3120 86.0 12480 240 9.45 1,08 10.1003.16 1” - 16 25,4 1.00 39,0 1.54 16.5 2390 65.0 9560 300 11.81 1,46 10.1003.20 1.1/4” - 20 32,0 1.25 49,8 1.96 12.5 1810 50.0 7240 420 16.54 2,17 10.1003.24 1.1/2” - 24 38,0 1.50 56,2 2.21 9.0 1300 36.0 5200 500 19.69 2,43 10.1003.32 2” - 32 50,8 2.00 68,8 2.71 8.0 1160 32.0 4640 630 24.80 3,09


Balflex® hydraulic hose DIN EN 853 2ST / SAE 100R2A has a very superior working and burst pressure compared

with only SAE 100R2A







Balflex® DIN EN 853 1SN / SAE 100R1AT SMOOTH COVER – 10.10S2.


SMOOTH COVER High pressure, smooth cover, single steel braid reinforced hydraulic hose

Inner tube:



Temperature range:

Couplings:

seamless oil resistant synthetic rubber 1 high tensile steel wire braid black, oil, weather and abrasion smooth resistant synthetic rubber 4: 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF); Intermittent service: + 120ºC (+ 248ºF) Max. temperature recommended for water base hydraulic fluids: + 70ºC (+ 158ºF) Max. temperature recommended for air: + 60ºC (+ 140ºF) Balflex


part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.10S2.04 1/4" - 4 6,3 0.25 13,4 0.53 22.5 3260 90.0 13040 100 3.9 0,26 10.10S2.05 5/16” - 5 8,0 0.31 15,0 0.59 21.5 3115 85.0 12460 114 4.5 0,30 10.10S2.06 3/8” - 6 9,5 0.38 17,4 0.69 18.0 2610 72.0 10440 127 5.0 0,36 10.10S2.08 1/2" - 8 12,7 0.50 20,7 0.81 16.0 2320 64.0 9280 178 7.0 0,46 10.10S2.10 5/8” - 10 16,0 0.63 23,8 0.93 13.0 1885 52.0 7540 200 7.9 0,56 10.10S2.12 3/4" - 12 19,0 0.75 27,8 1.09 10.5 1520 42.0 6080 240 9.4 0,74 10.10S2.16 1” - 16 25,4 1.00 35,9 1.40 8.8 1275 35.0 5100 300 11.8 1,06

Note: usually not available in stock, only by order.

Balflex

® hydraulic hose DIN EN 853 1SN / SAE 100R1AT has a very superior working and burst pressure compared with only SAE 100R1AT






Balflex® DIN EN 853 2SN / SAE 100R2AT SMOOTH COVER – 10.10S4.


SMOOTH COVER High pressure, smooth cover, double steel braid reinforced hydraulic hose

Inner tube:



Temperature range:

Couplings:

seamless oil resistant synthetic rubber 2 high tensile steel wire braids black, oil, weather and abrasion smooth resistant synthetic rubber 4: 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF); Intermittent service: + 120ºC (+ 248ºF) Max. temperature recommended for water base hydraulic fluids: + 70ºC (+ 158ºF) Max. temperature recommended for air: + 60ºC (+ 140ºF) Balflex


part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.10S4.04 1/4" - 4 6,3 0.25 15,0 0.59 40.0 5800 160.0 23200 100 3.9 0,38 10.10S4.05 5/16” - 5 8,0 0.31 16,6 0.65 35.0 5075 140.0 20300 114 4.5 0,45 10.10S4.06 3/8” - 6 9,5 0.38 19,0 0.75 33.0 4785 132.0 19140 127 5.0 0,53 10.10S4.08 1/2" - 8 12,7 0.50 22,2 0.87 27.5 3985 110.0 15940 178 7.0 0,65 10.10S4.10 5/8” - 10 16,0 0.63 25,5 1.00 25.0 3625 100.0 14500 200 7.9 0,76 10.10S4.12 3/4" - 12 19,0 0.75 29,4 1.15 21.5 3120 86.0 12480 240 9.4 1,00 10.10S4.16 1” - 16 25,4 1.00 37,9 1.50 16.5 2390 65.0 9560 300 11.8 1,48

Note: usually not available in stock, only by order.








Balflex ARTIC 1 LOW TEMPERATURE

Balflex® ARTIC 1 DIN EN 853 1SN / SAE 100R1AT – 10.1002.--LT



LOW TEMPERATURE - 60ºC (- 76ºF)

Inner tube:



Temperature range:

Couplings:

seamless oil resistant synthetic rubber resistant to low temperature 1 high tensile steel wire braid black, oil, weather and abrasion resistant synthetic rubber 4: 1 petroleum base hydraulic fluids - 60ºC (- 76ºF) + 100ºC (+ 212ºF) Max. temperature recommended for water base hydraulic fluids: + 70ºC (+ 158ºF) Max. temperature recommended for air: + 60ºC (+ 140ºF) Balflex


part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1002.03LT 3/16” - 3 4,8 0.19 11,8 0.47 25.0 3625 100.0 14500 89 3.5 0,23 10.1002.04LT 1/4" - 4 6,3 0.25 13,4 0.53 22.5 3260 90.0 13040 100 3.9 0,26 10.1002.05LT 5/16” - 5 8,0 0.31 15,0 0.59 21.5 3115 85.0 12460 114 4.5 0,30 10.1002.06LT 3/8” - 6 9,5 0.38 17,4 0.69 18.0 2610 72.0 10440 127 5.0 0,36 10.1002.08LT 1/2" - 8 12,7 0.50 20,7 0.81 16.0 2320 64.0 9280 178 7.0 0,46 10.1002.10LT 5/8” - 10 16,0 0.63 23,8 0.93 13.0 1885 52.0 7540 200 7.9 0,56 10.1002.12LT 3/4" - 12 19,0 0.75 27,8 1.09 10.5 1520 42.0 6080 240 9.4 0,74 10.1002.16LT 1” - 16 25,4 1.00 35,9 1.40 8.8 1275 35.0 5100 300 11.8 1,06 10.1002.20LT 1.1/4” - 20 32,0 1.25 43,8 1.71 6.3 910 25.0 3640 419 16.5 1,36 10.1002.24LT 1.1/2” - 24 38,0 1.50 51,1 1.99 5.0 725 20.0 2900 500 19.7 1,65 10.1002.32LT 2” - 32 50,8 2.00 64,5 2.52 4.0 580 16.0 2320 630 24.8 2,05

Balflex






Balflex ARTIC 2 LOW TEMPERATURE

Balflex® ARTIC 2 DIN EN 853 2SN / SAE 100R2AT – 10.1004.--LT



LOW TEMPERATURE - 60ºC (- 76ºF)

Inner tube:



Temperature range:

Couplings:

seamless oil resistant synthetic rubber resistant to low temperature 2 high tensile steel wire braids black, oil, weather and abrasion resistant synthetic rubber 4: 1 petroleum base hydraulic fluids - 60ºC (- 76ºF) + 100ºC (+ 212ºF) Max. temperature recommended for water base hydraulic fluids: + 70ºC (+ 158ºF) Max. temperature recommended for air: + 60ºC (+ 140ºF) Balflex


part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1004.03LT 3/16” - 3 4,8 0.19 13,4 0.53 41.5 6015 165.0 24060 89 3.5 0,32 10.1004.04LT 1/4" - 4 6,3 0.25 15,0 0.59 40.0 5800 160.0 23200 100 3.9 0,38 10.1004.05LT 5/16” - 5 8,0 0.31 16,6 0.65 35.0 5075 140.0 20300 114 4.5 0,45 10.1004.06LT 3/8” - 6 9,5 0.38 19,0 0.75 33.0 4785 132.0 19140 127 5.0 0,53 10.1004.08LT 1/2" - 8 12,7 0.50 22,2 0.87 27.5 3985 110.0 15940 178 7.0 0,65 10.1004.10LT 5/8” - 10 16,0 0.63 25,5 1.00 25.0 3625 100.0 14500 200 7.9 0,76 10.1004.12LT 3/4" - 12 19,0 0.75 29,4 1.15 21.5 3120 86.0 12480 240 9.4 1,00 10.1004.16LT 1” - 16 25,4 1.00 37,9 1.50 16.5 2390 65.0 9560 300 11.8 1,48 10.1004.20LT 1.1/4” - 20 32,0 1.25 48,5 1.90 12.5 1810 50.0 7240 419 16.5 2,14 10.1004.24LT 1.1/2” - 24 38,0 1.50 54,7 2.15 9.0 1300 36.0 5200 500 19.7 2,55 10.1004.32LT 2” - 32 50,8 2.00 67,4 2.65 8.0 1160 32.0 4640 630 24.8 3,30







Balflex TROPIC 1 HIGH TEMPERATURE

Balflex® TROPIC 1 DIN EN 853 1SN / SAE 100R1AT – 10.1002.--HT



HIGH TEMPERATURE

+ 150ºC (+ 302ºF) intermittent service + 135ºC (+ 275ºF) continuous service

Inner tube:



Temperature range:

Couplings:

seamless oil resistant synthetic rubber resistant to high temperature 1 high tensile steel wire braid black, oil, weather and abrasion resistant synthetic rubber 4: 1 petroleum base hydraulic fluids intermittent: - 40ºC (- 40ºF) + 150ºC (+ 302ºF); continuous service: + 135ºC (+ 275ºF) Max. temperature recommended for water base hydraulic fluids: + 120ºC (+ 248ºF) Max. temperature recommended for air: + 60ºC (+ 140ºF) Balflex


part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1002.03HT 3/16” - 3 4,8 0.19 11,8 0.47 25.0 3625 100.0 14500 89 3.5 0,23 10.1002.04HT 1/4" - 4 6,3 0.25 13,4 0.53 22.5 3260 90.0 13040 100 3.9 0,26 10.1002.05HT 5/16” - 5 8,0 0.31 15,0 0.59 21.5 3115 85.0 12460 114 4.5 0,30 10.1002.06HT 3/8” - 6 9,5 0.38 17,4 0.69 18.0 2610 72.0 10440 127 5.0 0,36 10.1002.08HT 1/2" - 8 12,7 0.50 20,7 0.81 16.0 2320 64.0 9280 178 7.0 0,46 10.1002.10HT 5/8” - 10 16,0 0.63 23,8 0.93 13.0 1885 52.0 7540 200 7.9 0,56 10.1002.12HT 3/4" - 12 19,0 0.75 27,8 1.09 10.5 1520 42.0 6080 240 9.4 0,74 10.1002.16HT 1” - 16 25,4 1.00 35,9 1.40 8.8 1275 35.0 5100 300 11.8 1,06 10.1002.20HT 1.1/4” - 20 32,0 1.25 43,8 1.71 6.3 910 25.0 3640 419 16.5 1,36 10.1002.24HT 1.1/2” - 24 38,0 1.50 51,1 1.99 5.0 725 20.0 2900 500 19.7 1,65 10.1002.32HT 2” - 32 50,8 2.00 64,5 2.52 4.0 580 16.0 2320 630 24.8 2,05

Balflex






Balflex TROPIC 2 HIGH TEMPERATURE

Balflex® TROPIC 2 DIN EN 853 2SN / SAE 100R2AT – 10.1004.--HT



HIGH TEMPERATURE


Inner tube:



Temperature range:

Couplings:

seamless oil resistant synthetic rubber resistant to high temperature 2 high tensile steel wire braids black, oil, weather and abrasion resistant synthetic rubber 4: 1 petroleum base hydraulic fluids intermittent: - 40ºC (- 40ºF) + 150ºC (+ 302ºF); continuous service: + 135ºC (+ 275ºF) Max. temperature recommended for water base hydraulic fluids: + 120ºC (+ 248ºF) Max. temperature recommended for air: + 60ºC (+ 140ºF) Balflex


part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1004.03HT 3/16” - 3 4,8 0.19 13,4 0.53 41.5 6015 165.0 24060 89 3.5 0,32 10.1004.04HT 1/4" - 4 6,3 0.25 15,0 0.59 40.0 5800 160.0 23200 100 3.9 0,38 10.1004.05HT 5/16” - 5 8,0 0.31 16,6 0.65 35.0 5075 140.0 20300 114 4.5 0,45 10.1004.06HT 3/8” - 6 9,5 0.38 19,0 0.75 33.0 4785 132.0 19140 127 5.0 0,53 10.1004.08HT 1/2" - 8 12,7 0.50 22,2 0.87 27.5 3985 110.0 15940 178 7.0 0,65 10.1004.10HT 5/8” - 10 16,0 0.63 25,5 1.00 25.0 3625 100.0 14500 200 7.9 0,76 10.1004.12HT 3/4" - 12 19,0 0.75 29,4 1.15 21.5 3120 86.0 12480 240 9.4 1,00 10.1004.16HT 1” - 16 25,4 1.00 37,9 1.50 16.5 2390 65.0 9560 300 11.8 1,48 10.1004.20HT 1.1/4” - 20 32,0 1.25 48,5 1.90 12.5 1810 50.0 7240 419 16.5 2,14 10.1004.24HT 1.1/2” - 24 38,0 1.50 54,7 2.15 9.0 1300 36.0 5200 500 19.7 2,55 10.1004.32HT 2” - 32 50,8 2.00 67,4 2.65 8.0 1160 32.0 4640 630 24.8 3,30







Balflex BALPAC PREMIUM SAE 100R16

Balflex® BALPAC PREMIUM SAE 100R16 – 10.1019.

According to SAE J517 Norm type / SAE 100R16 / ISO 11237 –1 Norm type R16

Exceeds SAE 100R16 Very High pressure, double steel wire braid reinforced hydraulic hose

Inner tube:



Temperature range:

Couplings:



part number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1019.04 1/4" - 4 6,3 0.25 13,3 0.52 40.0 5800 160.0 23200 50 2.0 0,27 10.1019.05 5/16” - 5 8,0 0.31 15,0 0.59 35.0 5075 140.0 20300 57 2,2 0,30 10.1019.06 3/8” - 6 9,5 0.38 17,1 0.67 33.0 4785 132.0 19140 65 2.6 0,42 10.1019.08 1/2" - 8 12,7 0.50 20,6 0.81 27.6 4000 110.4 16000 90 3.5 0,52 10.1019.10 5/8” - 10 16,0 0.63 23,7 0.93 25.0 3625 100.0 14500 100 3.9 0,63 10.1019.12 3/4" - 12 19,0 0.75 27,7 1.09 21.5 3118 86.0 12472 120 4.7 0,80 10.1019.16 1” - 16 25,4 1.00 35,8 1.41 16.5 2393 66.0 9572 150 5.9 1,22





Balflex BALPAC 3000 SAE 100R17

Balflex® BALPAC 3000 SAE 100R17 – 10.1017.


High pressure, single or double steel braid reinforced hydraulic hose


Outer tube:


Temperature range:

Couplings:

seamless oil resistant synthetic rubber 1 high tensile steel wire braid on sizes 1/4", 5/16”, 3/8” and 1/2" and 2 braids on sizes 5/8”, 3/4" and 1” black, oil, weather and abrasion resistant synthetic rubber 4: 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF); Intermittent service: + 120ºC (+ 248ºF) Max. temperature recommended for water base hydraulic fluids: + 70ºC (+ 158ºF) Max. temperature recommended for air: + 60ºC (+ 140ºF) Balflex

® crimped fittings series 23 with ferrules series 20.204 (2 wires) & 20.205 (1 wire).

Multicrimp P23 serie

part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight

mm inch mm inch MPa PSI MPa PSI mm inch Kg./m

1 Wire Braid

10.1017.04 1/4" - 4 6,3 0.25 12,7 0.50 22.5 3260 90.0 13040 51 2.0 0.22 10.1017.05 5/16” - 5 8,0 0.31 15,0 0.59 21.0 3000 84.0 12000 60 2.4 0,27 10.1017.06 3/8” - 6 9,5 0.38 16,5 0.65 21.0 3000 84.0 12000 64 2.5 0.34 10.1017.08 1/2" - 8 12,7 0.50 20,8 0.82 21.0 3000 84.0 12000 89 3.5 0.42

2 Wire Braid

10.1017.10 5/8” - 10 15,9 0.63 24,7 0.97 25.0 3625 100.0 14500 102 4.0 0.51 10.1017.12 3/4" - 12 19,0 0.75 28,6 1.13 21.5 3120 86.0 12480 122 4.8 0.63 10.1017.16 1” - 16 25,4 1.00 36,6 1.48 20.7 3000 82.8 12000 152 6.0 1.00





Balflex – The European Technology (I) HYDR-2010 - 46 Balflex 2010

Balflex BALPAC DIN EN 1SC

Balflex® BALPAC DIN EN 857 1SC – 10.1017. / 10.1018.

According to ISO 11237 –1 Norm type 1SC / DIN EN 857 Norm type 1SC


Inner tube:



Temperature range:

Couplings:

seamless oil resistant synthetic rubber 1 high tensile steel wire braid black, oil, weather and abrasion resistant synthetic rubber 4 : 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF); Intermittent service: + 120ºC (+ 248ºF) Max. temperature recommended for water base hydraulic fluids: + 70ºC (+ 158ºF) Max. temperature recommended for air: + 60ºC (+ 140ºF) Balflex

® crimped fittings series 23 with ferrules series 20

part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1017.

10.1017.04 1/4" - 4 6,3 0.25 12,7 0.50 22.5 3260 90.0 13040 51 2.0 0.22 10.1017.05 5/16” - 5 8,0 0.31 15,0 0.59 21.0 3000 84.0 12000 60 2.4 0,27 10.1017.06 3/8” - 6 9,5 0.38 16,5 0.65 21.0 3000 84.0 12000 64 2.5 0.34 10.1017.08 1/2" - 8 12,7 0.50 20,8 0.82 21.0 3000 84.0 12000 89 3.5 0.42

10.1018.

10.1018.10 5/8” - 10 15,9 0.63 23.0 0.90 13.0 1885 52.0 7540 102 4.0 0.51 10.1018.12 3/4" - 12 19,0 0.75 26.7 1.05 10.5 1523 42.0 6090 122 4.8 0.63 10.1018.16 1” - 16 25,4 1.00 34.9 1.37 8.8 1276 35.2 5104 152 6.0 1.00





Balflex – The European Technology Balflex 2010 (I) HYDR-2010 - 47

Balflex BALPAC PREMIUM DIN EN 2SC

Balflex® BALPAC PREMIUM DIN EN 857 2SC – 10.1019.



Inner tube :

Reinforcement : Outer tube :

Safety factor : Application :

Temperature range :

Couplings :

seamless oil resistant synthetic rubber 2 high tensile steel wire braid black, oil, weather and abrasion resistant synthetic rubber 4 : 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF); Intermittent service: + 120ºC (+ 248ºF) Max. temperature recommended for water base hydraulic fluids: + 70ºC (+ 158ºF) Max. temperature recommended for air: + 60ºC (+ 140ºF) Balflex


part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1019.04 1/4" - 4 6,3 0.25 13,3 0.52 40.0 5800 160.0 23200 50 2.0 0.27 10.1019.05 5/16” - 5 8,0 0.31 15,0 0.59 35.0 5075 140.0 20300 57 2.2 0,30 10.1019.06 3/8” - 6 9,5 0.38 17,1 0.67 33.0 4785 132.0 19140 65 2.6 0.42 10.1019.08 1/2" - 8 12,7 0.50 20,6 0.81 27.6 4000 110.4 16000 90 3.5 0.52 10.1019.10 5/8” - 10 15,9 0.63 23,7 0.93 25.0 3625 100.0 14500 100 3.9 0.63 10.1019.12 3/4" - 12 19,0 0.75 27,7 1.09 21.5 3118 86.0 12472 120 4.7 0.80 10.1019.16 1” - 16 25,4 1.00 35,8 1.41 16.5 2393 66.0 9572 150 5.9 1.22






Balflex SAE 100R5 / SAE J 1402 AII

Balflex® SAE 100R5 / SAE J 1402 AII – 10.1007.

According to SAE J517 type SAE 100R5 / SAE J 1402 type AII

High pressure hydraulic hose with steel and textile braids reinforcement with rubber impregnated textile cover

Inner tube:


Safety factor:


Couplings:

seamless oil resistant synthetic rubber 2 high resistance synthetic textile braids with an intermediate high tensile steel wire braid impregnation of the outer textile braid with black, oil, weather and abrasion resistant synthetic rubber 4: 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF); Intermittent service: + 120ºC (+ 248ºF) Max. temperature recommended for water base hydraulic fluids: + 70ºC (+ 158ºF) Max. temperature recommended for air: + 60ºC (+ 140ºF) Balflex

® crimped fittings P25 serie

part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1007.04 3/16” - 4 4,8 0.19 13,2 0.52 20.7 3000 82.8 12000 76 3.00 0,19 10.1007.05 1/4" - 5 6,3 0.25 14,8 0.60 20.7 3000 82.8 12000 86 3.38 0,27 10.1007.06 5/16” - 6 8,0 0.31 17,2 0.68 15.5 2250 62.0 9000 102 4.00 0,29 10.1007.08 13/32” - 8 10,4 0.41 19,5 0.77 13.8 2000 55.2 8000 117 4.62 0,36 10.1007.10 1/2" - 10 12,7 0.50 23,4 0.92 12.1 1755 48.3 7020 140 5.50 0,45 10.1007.12 5/8” - 12 16,0 0.63 27,4 1.08 10.3 1495 41.4 5980 165 6.50 0,56 10.1007.16 7/8” - 16 22,2 0.88 31,4 1.24 5.5 800 22.1 3200 187 7.38 0,78 10.1007.20 1.1/8” - 20 28,6 1.13 38,1 1.50 4.3 625 17.2 2500 229 9.00 1,06 10.1007.24 1.3/8” - 24 34,9 1.38 44,5 1.75 3.4 500 13.8 2000 267 10.50 1,45 10.1007.32 1.13/16” - 32 46,0 1.81 56,4 2.22 2.4 350 9.7 1400 337 13.20 1,70 10.1007.40 2.3/8” - 40 60,3 2.38 73,0 2.87 2.4 350 9.7 1400 610 24.00 2,15 10.1007.48 3” - 48 76,2 3.00 90,5 3.56 1.4 200 5.5 800 838 33.00 3,08

High pressure hydraulic hose with steel and textile braids reinforcement with rubber cover

Balflex® SAE 100R5R – 10.1006.

SAE 100R5 hydraulic hose with rubber cover





Balflex SAE 100R5 HEATMASTER

Balflex® SAE 100R5 HEATMASTER 150oC / 302oF – 10.1007.--HT

According to SAE J517 type SAE 100R5

High pressure HIGH TEMPERATURE hydraulic hose with steel and textile braids reinforcement with blue rubber impregnated textile cover

HIGH TEMPERATURE


Inner tube:


Safety factor:


Couplings:

seamless oil resistant synthetic rubber 2 high resistance synthetic textile braids with an intermediate high tensile steel wire braid impregnation of the outer textile blue braid with oil, weather and abrasion resistant synthetic rubber 4: 1 petroleum base hydraulic fluids and hot air in compressors intermittent: - 40ºC (- 40ºF) + 150ºC (+ 302ºF); continuous service + 135ºC (+ 275ºF) Max. temperature recommended for water base hydraulic fluids: + 70ºC (+ 158ºF) Max. temperature recommended for air: + 60ºC (+ 140ºF) Balflex

® crimped fittings P25 serie

part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1007.04HT 3/16” - 4 4,8 0.19 13,2 0.52 20.7 3000 82.8 12000 76 3.00 0,19 10.1007.05HT 1/4" - 5 6,3 0.25 14,8 0.60 20.7 3000 82.8 12000 86 3.38 0,27 10.1007.06HT 5/16” - 6 8,0 0.31 17,2 0.68 15.5 2250 62.0 9000 102 4.00 0,29 10.1007.08HT 13/32” - 8 10,4 0.41 19,5 0.77 13.8 2000 55.2 8000 117 4.62 0,36 10.1007.10HT 1/2" - 10 12,7 0.50 23,4 0.92 12.1 1755 48.3 7020 140 5.50 0,45 10.1007.12HT 5/8” - 12 16,0 0.63 27,4 1.08 10.3 1495 41.4 5980 165 6.50 0,56 10.1007.16HT 7/8” - 16 22,2 0.88 31,4 1.24 5.5 800 22.1 3200 187 7.38 0,78 10.1007.20HT 1.1/8” - 20 28,6 1.13 38,1 1.50 4.3 625 17.2 2500 229 9.00 1,06 10.1007.24HT 1.3/8” - 24 34,9 1.38 44,5 1.75 3.4 500 13.8 2000 267 10.50 1,45 10.1007.32HT 1.13/16” - 32 46,0 1.81 56,4 2.22 2.4 350 9.7 1400 337 13.20 1,70 10.1007.40HT 2.3/8” - 40 60,3 2.38 73,0 2.87 2.4 350 9.7 1400 610 24.00 2,15 10.1007.48HT 3” - 48 76,2 3.00 90,5 3.56 1.4 200 5.5 800 838 33.00 3,08





Balflex 2 – MAX JACK

Balflex® 2 – MAX JACK 1/4" 3/8” 10.000PSI and 1/2" 8000PSI – 10.1029.





Couplings:

seamless oil resistant synthetic rubber 2 high tensile steel wire braids black, oil, weather and abrasion resistant synthetic rubber 2.3: 1 (1/4”) and 2: 1 (3/8” and 1/2”) hydraulic jacks - 40ºC (- 40ºF) + 100ºC (+ 212ºF); Intermittent service: + 120ºC (+ 248ºF) Max. temperature recommended for water base hydraulic fluids: + 70ºC (+ 158ºF) Max. temperature recommended for air: + 60ºC (+ 140ºF) Balflex


part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1029.04 1/4" - 4 6,3 0.25 15,0 0.59 70.0 10000 160.0 23200 100 3.9 0,38 10.1029.06 3/8” - 6 9,5 0.38 19,0 0.75 70.0 10000 140.0 20000 127 5.0 0,53 10.1029.08 1/2" - 8 12,7 0.50 22,2 0.87 55.2 8000 110.4 16000 178 7.0 0,65


Balflex 3 – MAX

Balflex® 3 - MAX – 10.1005.

Very high pressure, triple steel braid reinforced hydraulic hose




Couplings:


® crimped fittings 23 serie or 24 with ferrules 20 serie

part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1005.06 3/8” - 6 9,5 0.38 21,4 0.84 50.0 7200 200.0 28800 150 5.9 0,70 10.1005.08 1/2" - 8 12,7 0.50 24,6 0.97 47.0 6800 188.0 27200 200 7.9 0,80

The Balflex® 3 – MAX hydraulic hose is a hose developed by Balflex

® with special technical specification to attend higher working pressures.






Balflex BALMASTER SAE 100R12

Balflex® BALMASTER EN 856 R12 / SAE 100R12 – 10.1012.

According to ISO 3862 / EN 856 type R12 / SAE J517 type SAE 100R12

High pressure, four steel wire spirals reinforced hydraulic hose

Inner tube:



Temperature range:

Couplings:

seamless oil resistant synthetic rubber 4 spirals of high tensile steel wire black, oil, weather and abrasion resistant synthetic rubber 4: 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF); Intermittent service: + 120ºC (+ 248ºF) Max. temperature recommended for water base hydraulic fluids: + 70ºC (+ 158ºF) Max. temperature recommended for air: + 60ºC (+ 140ºF) Balflex

® crimped fittings 23 or 24 series with ferrules 20 serie

part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1012.06 3/8” - 6 9,5 0.38 20,3 0.80 27.6 4000 110.0 16000 125 5.0 0,80 10.1012.08 1/2" - 8 12,7 0.50 23,6 0.93 27.6 4000 110.0 16000 180 7.0 1,15 10.1012.10 5/8” - 10 16,0 0.63 27,4 1.08 27.6 4000 110.0 16000 205 8.0 1,26 10.1012.12 3/4" - 12 19,0 0.75 30,7 1.21 27.6 4000 110.0 16000 240 9.5 1,44 10.1012.16 1” - 16 25,4 1.00 38,1 1.50 27.6 4000 110.0 16000 305 12.0 2,15 10.1012.20 1.1/4” - 20 32,0 1.25 47,0 1.85 20.7 3000 82.7 12000 420 16.5 2,75 10.1012.24 1.1/2” - 24 38,0 1.50 53,6 2.11 17.2 2500 69.0 10000 510 20.0 3,35 10.1012.32 2” - 32 50,8 2.00 66,8 2.63 17.2 2500 69.0 10000 635 25.0 4,60






Balflex BALMASTER DIN EN 856 4SP

Balflex® BALMASTER EN 856 4SP – 10.1008.

According to ISO 3862 / EN 856 type 4SP

Very high pressure, four steel wire spirals reinforced hydraulic hose

Inner tube:



Temperature range:

Couplings:

seamless oil resistant synthetic rubber 4 spirals of high tensile steel wire black, oil, weather and abrasion resistant synthetic rubber 4: 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF); Intermittent service: + 120ºC (+ 248ºF) Max. temperature recommended for water base hydraulic fluids: + 70ºC (+ 158ºF) Max. temperature recommended for air: + 60ºC (+ 140ºF) Balflex

® crimped fittings series 24 with ferrules 20 serie

part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1008.04 1/4" - 4 6,6 0.26 17,9 0.70 50.0 7250 200.0 29000 120 4.7 0,70 10.1008.06 3/8” - 6 9,5 0.38 21,4 0.84 44.5 6453 178.0 25812 130 5.1 0,80 10.1008.08 1/2" - 8 12,7 0.50 24,6 0.97 41.5 6018 166.0 24072 180 7.1 1,15 10.1008.10 5/8” - 10 16,0 0.63 28,2 1.11 35.0 5075 140.0 20300 225 8.9 1,26 10.1008.12 3/4" - 12 19,0 0.75 32,2 1.27 35.0 5075 140.0 20300 280 11.0 1,44 10.1008.16 1” - 16 25,4 1.00 39,7 1.56 28.0 4060 112.0 16240 355 14.0 2,15 10.1008.20 1.1/4” - 20 32,0 1.25 50,8 2.00 21.0 3045 84.0 12180 460 18.1 2,75 10.1008.24 1.1/2” - 24 38,0 1.50 57,2 2.25 18.5 2683 74.0 10732 560 22.0 3,35 10.1008.32 2” - 32 50,8 2.00 69,8 2.75 16.5 2393 66.0 9572 710 28.0 4,60






Balflex POWERSPIR DIN EN 856 4SH

Balflex® POWERSPIR EN 856 4SH – 10.1009.

According to ISO 3862 / EN 856 type 4SH


Inner tube:



Temperature range:

Couplings:

seamless oil resistant synthetic rubber 4 spirals of very high tensile steel wire black, oil, weather and abrasion resistant synthetic rubber 4: 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF); Intermittent service: + 120ºC (+ 248ºF) Max. temperature recommended for water base hydraulic fluids: + 70ºC (+ 158ºF) Max. temperature recommended for air: + 60ºC (+ 140ºF) Balflex

® crimped fittings series 26 with ferrules 20.406. (3/4” and 1”) and 20.405. (1.1/4”,

1.1/2” and 2”) series

part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1009.12 3/4" - 12 19,0 0.75 32,2 1.27 42.0 6090 168.0 24360 280 11.0 1,56 10.1009.16 1” - 16 25,4 1.00 38,7 1.52 38.0 5510 152.0 22040 340 13.4 2,09 10.1009.20 1.1/4” - 20 32,0 1.25 45,5 1.79 32.5 4713 130.0 18852 460 18.1 2,57 10.1009.24 1.1/2” - 24 38,0 1.50 53,5 2.11 29.0 4205 116.0 16820 560 22.0 3,44 10.1009.32 2” - 32 50,8 2.00 68,1 2.68 25.0 3625 100.0 14500 700 27.6 4,90

* On sizes – 12 (3/4”) and – 16 (1”) the Balflex

® POWERSPIR DIN EN 856 4SH and SAE 100R13 hoses

are the same. The working pressure of Balflex® POWERSPIR DIN EN 856 4SH SAE 100R13 3/4" and

Balflex® POWERSPIR DIN EN 856 4SH SAE 100R13 1” are higher than standard SAE 100R13.

* On size – 12 (3/4”) the Balflex

® POWERSPIR DIN EN 856 4SH, SAE 100R13 and SAE 100R15 hoses

are the same






Balflex POWERSPIR SAE 100R13

Balflex® POWERSPIR SAE 100R13 – 5000PSI – 10.1009. * - 10.1014.

According to ISO 3862 / EN 856 type R13 / SAE J517 type R13

Very high pressure, four or six steel wire spirals reinforced hydraulic hose

Inner tube:



Temperature range:

Couplings:

seamless oil resistant synthetic rubber 4 or 6 spirals of high tensile steel wire black, oil, weather and abrasion resistant synthetic rubber 4: 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF); Intermittent service: + 120ºC (+ 248ºF) Max. temperature recommended for water base hydraulic fluids: + 70ºC (+ 158ºF) Max. temperature recommended for air: + 60ºC (+ 140ºF) Balflex

® crimped fittings series 26 with ferrules 20.406 serie

part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1009.12 * 3/4" - 12 19,0 0.75 32,2 1.27 42.0 6090 168.0 24360 280 11.0 1,56 10.1009.16 * 1” - 16 25,4 1.00 38,7 1.52 38.0 5510 152.0 22040 340 13.4 2,09 10.1014.20 1.1/4” - 20 32,0 1.25 49,8 1.96 34.5 5000 138.0 20000 420 16.5 3,90 10.1014.24 1.1/2” - 24 38,0 1.50 57,4 2.26 34.5 5000 138.0 20000 500 20.0 4,96 10.1014.32 2” - 32 50,8 2.00 71,1 2.80 34.5 5000 138.0 20000 635 25.0 7,09

Note: According to ISO 3862 / EN 856 type R13 / SAE J517 type R13, the Balflex® POWERSPIR SAE

100R13 hose is of 4 steel wire spirals on sizes – 12 (3/4”) and – 16 (1”) and of 6 steel wire spirals on sizes – 20 (1.1/4”), – 24 (1.1/2”) and – 32 (2”). * On sizes – 12 (3/4”) and – 16 (1”) the Balflex










Balflex® POWERSPIR SAE 100R15 – 6000PSI – 10.1016.



Inner tube:



Temperature range:

Couplings:

seamless oil resistant synthetic rubber 4 or 6 spirals of high tensile steel wire black, oil, weather and abrasion resistant synthetic rubber 4: 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF); Intermittent service: + 120ºC (+ 248ºF) Max. temperature recommended for water base hydraulic fluids: + 70ºC (+ 158ºF) Max. temperature recommended for air: + 60ºC (+ 140ºF) Balflex


part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1016.06 3/8” - 6 9,5 0.38 23,3 0.92 41.4 6000 165.5 24000 153 6.0 0,75 10.1016.08 1/2" - 8 12,7 0.50 26,8 1.06 41.4 6000 165.5 24000 203 8.0 0,89 10.1009.12* 3/4" - 12 19,0 0.75 36,1 1.42 41.4 6000 165.5 24000 267 10.5 1,56 10.1016.16 1” - 16 25,4 1.00 42,9 1.69 41.4 6000 165.5 24000 330 13.0 2,10 10.1016.20 1.1/4” - 20 32,0 1.25 51,5 2.03 41.4 6000 165.5 24000 445 17.5 3,65 10.1016.24 1.1/2” - 24 38,0 1.50 59,6 2.32 41.4 6000 165.5 24000 533 21.0 5,00


100R15 hose is of 4 steel wire spirals on sizes – 6 (3/8”), 8 (1/2”), – 12 (3/4”) and – 16 (1”) and of 6 steel wire spirals on sizes – 20 (1.1/4”) and – 24 (1.1/2”).

According to ISO 3862 / SAE J517 type R15 doesn’t exist the size – 32 (2”).


® POWERSPIR DIN EN 856 4SH and SAE 100R15 hoses are the same







Balflex® ARMORGUARD DIN EN 853 1SN / SAE 100R1AT – 10.1002.--A


Balflex ARMORGUARD VERY HIGH ABRASION RESISTANCE High pressure, single steel braid reinforced hydraulic hose

Inner tube:



Temperature range:

Couplings:

seamless oil resistant synthetic rubber 1 high tensile steel wire braid black, oil, weather and VERY HIGH abrasion resistant synthetic rubber 4: 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF); Intermittent service: + 120ºC (+ 248ºF) Max. temperature recommended for water base hydraulic fluids: + 70ºC (+ 158ºF) Max. temperature recommended for air: + 60ºC (+ 140ºF) Balflex


part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1002.03A 3/16” - 3 4,8 0.19 11,8 0.47 25.0 3625 100.0 14500 89 3.5 0,23 10.1002.04A 1/4" - 4 6,3 0.25 13,4 0.53 22.5 3260 90.0 13040 100 3.9 0,26 10.1002.05A 5/16” - 5 8,0 0.31 15,0 0.59 21.5 3115 85.0 12460 114 4.5 0,30 10.1002.06A 3/8” - 6 9,5 0.38 17,4 0.69 18.0 2610 72.0 10440 127 5.0 0,36 10.1002.08A 1/2" - 8 12,7 0.50 20,7 0.81 16.0 2320 64.0 9280 178 7.0 0,46 10.1002.10A 5/8” - 10 16,0 0.63 23,8 0.93 13.0 1885 52.0 7540 200 7.9 0,56 10.1002.12A 3/4" - 12 19,0 0.75 27,8 1.09 10.5 1520 42.0 6080 240 9.4 0,74 10.1002.16A 1” - 16 25,4 1.00 35,9 1.40 8.8 1275 35.0 5100 300 11.8 1,06 10.1002.20A 1.1/4” - 20 32,0 1.25 43,8 1.71 6.3 910 25.0 3640 419 16.5 1,36 10.1002.24A 1.1/2” - 24 38,0 1.50 51,1 1.99 5.0 725 20.0 2900 500 19.7 1,65 10.1002.32A 2” - 32 50,8 2.00 64,5 2.52 4.0 580 16.0 2320 630 24.8 2,05 10.1002.40A 2.1/2” - 40 63,5 2.50 79,0 3.11 5.0 725 20.0 2900 760 30.4 2,89 10.1002.48A 3 “ - 48 76,2 3.00 92,0 3.62 3.5 508 14.0 2030 900 36.0 3,43










Balflex® ARMORGUARD DIN EN 853 2SN / SAE 100R2AT – 10.1004.--A


Balflex ARMORGUARD VERY HIGH ABRASION RESISTANCE


Inner tube:



Temperature range:

Couplings:

seamless oil resistant synthetic rubber 2 high tensile steel wire braids black, oil, weather and VERY HIGH abrasion resistant synthetic rubber 4: 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF); Intermittent service: + 120ºC (+ 248ºF) Max. temperature recommended for water base hydraulic fluids: + 70ºC (+ 158ºF) Max. temperature recommended for air: + 60ºC (+ 140ºF) Balflex


part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1004.03A 3/16” - 3 4,8 0.19 13,4 0.53 41.5 6015 165.0 24060 89 3.5 0,32 10.1004.04A 1/4" - 4 6,3 0.25 15,0 0.59 40.0 5800 160.0 23200 100 3.9 0,38 10.1004.05A 5/16” - 5 8,0 0.31 16,6 0.65 35.0 5075 140.0 20300 114 4.5 0,45 10.1004.06A 3/8” - 6 9,5 0.38 19,0 0.75 33.0 4785 132.0 19140 127 5.0 0,53 10.1004.08A 1/2" - 8 12,7 0.50 22,2 0.87 27.5 3985 110.0 15940 178 7.0 0,65 10.1004.10A 5/8” - 10 16,0 0.63 25,5 1.00 25.0 3625 100.0 14500 200 7.9 0,76 10.1004.12A 3/4" - 12 19,0 0.75 29,4 1.15 21.5 3120 86.0 12480 240 9.4 1,00 10.1004.16A 1” - 16 25,4 1.00 37,9 1.50 16.5 2390 65.0 9560 300 11.8 1,48 10.1004.20A 1.1/4” - 20 32,0 1.25 48,5 1.90 12.5 1810 50.0 7240 419 16.5 2,14 10.1004.24A 1.1/2” - 24 38,0 1.50 54,7 2.15 9.0 1300 36.0 5200 500 19.7 2,55 10.1004.32A 2” - 32 50,8 2.00 67,4 2.65 8.0 1160 32.0 4640 630 24.8 3,30 10.1004.40A 2.1/2” - 40 63,5 2.50 83,0 3.27 7.0 1015 28.0 4060 760 30.4 3,96 10.1004.48A 3 “ - 48 76,2 3.00 96,0 3.78 5.5 798 22.0 3192 900 36.0 4,96

Note: Size - 48 (3”) not included in the standards.









Balflex® ARMORGUARD DIN EN 853 1ST / SAE 100R1A – 10.1001.--A



THICK COVER - High pressure, single steel braid reinforced hydraulic hose

Inner tube:



Temperature range:

Couplings:

seamless oil resistant synthetic rubber 1 high tensile steel wire braid black, oil, weather and VERY HIGH abrasion resistant synthetic rubber 4: 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF); Intermittent service: + 120ºC (+ 248ºF) Max. temperature recommended for water base hydraulic fluids: + 70ºC (+ 158ºF) Max. temperature recommended for air: + 60ºC (+ 140ºF) Balflex


part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1001.04A 1/4" - 4 6,3 0.25 15,5 0.61 22.5 3260 90.0 13040 100 3.94 0,29 10.1001.05A 5/16” - 5 8,0 0.31 17,1 0.67 21.5 3115 85.0 12460 115 4.53 0,34 10.1001.06A 3/8” - 6 9,5 0.38 19,4 0.76 18.0 2610 72.0 10440 130 5.12 0,42 10.1001.08A 1/2" - 8 12,7 0.50 22,6 0.89 16.0 2320 64.0 9280 180 7.09 0,51 10.1001.10A 5/8” - 10 16,0 0.63 25,8 1.02 13.0 1885 52.0 7540 200 7.87 0,59 10.1001.12A 3/4" - 12 19,0 0.75 29,8 1.17 10.5 1520 42.0 6080 240 9.45 0,73 10.1001.16A 1” - 16 25,4 1.00 37,6 1.48 8.8 1275 35.0 5100 300 11.81 1,05 10.1001.20A 1.1/4” - 20 32,0 1.25 45,0 1.77 6.3 910 25.0 3640 420 16.54 1,36 10.1001.24A 1.1/2” - 24 38,0 1.50 51,4 2.02 5.0 725 20.0 2900 500 19.68 1,56 10.1001.32A 2” - 32 50,8 2.00 66,4 2.61 4.0 580 16.0 2320 630 24.80 2,30


Balflex

® hydraulic hose DIN EN 853 1ST / SAE 100R1A has a very superior working and burst pressure compared with only SAE 100R1A






Balflex® ARMORGUARD DIN EN 853 2ST / SAE 100R2A – 10.1003.--A



THICK COVER - High pressure, double steel braid reinforced hydraulic hose

Inner tube:



Temperature range:

Couplings:



part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1003.04A 1/4" - 4 6,3 0.25 17,1 0.67 40.0 5800 160.0 23200 100 3.94 0,45 10.1003.05A 5/16” - 5 8,0 0.31 18,7 0.74 35.0 5075 140.0 20300 115 4.53 0,52 10.1003.06A 3/8” - 6 9,5 0.38 21,0 0.83 33.0 4785 132.0 19140 130 5.12 0,64 10.1003.08A 1/2" - 8 12,7 0.50 24,2 0.95 27.5 3985 110.0 15940 180 7.09 0,75 10.1003.10A 5/8” - 10 16,0 0.63 27,4 1.08 25.0 3625 100.0 14500 200 7.87 0,88 10.1003.12A 3/4" - 12 19,0 0.75 31,4 1.24 21.5 3120 86.0 12480 240 9.45 1,08 10.1003.16A 1” - 16 25,4 1.00 39,0 1.54 16.5 2390 65.0 9560 300 11.81 1,46 10.1003.20A 1.1/4” - 20 32,0 1.25 49,8 1.96 12.5 1810 50.0 7240 420 16.54 2,17 10.1003.24A 1.1/2” - 24 38,0 1.50 56,2 2.21 9.0 1300 36.0 5200 500 19.69 2,43 10.1003.32A 2” - 32 50,8 2.00 68,8 2.71 8.0 1160 32.0 4640 630 24.80 3,09


Balflex

® hydraulic hose DIN EN 853 2ST / SAE 100R2A has a very superior working and burst pressure compared with only SAE 100R2A COVER: U.S. MSHA APPROVED Construction characteristics and dimensions may be changed at any time without prior notice.




Balflex BALPAC PREMIUM SAE 100R16

Balflex® ARMORGUARD BALPAC PREMIUM SAE 100R16 – 10.1019.--A



Exceeds SAE 100R16 Very High pressure, double steel wire braid reinforced hydraulic hose

Inner tube:



Temperature range:

Couplings:



part number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1019.04A 1/4" - 4 6,3 0.25 13,3 0.52 40.0 5800 160.0 23200 50 2.0 0,27 10.1019.05A 5/16” - 5 8,0 0.31 15,0 0.59 35.0 5075 140.0 20300 57 2,2 0,30 10.1019.06A 3/8” - 6 9,5 0.38 17,1 0.67 33.0 4785 132.0 19140 65 2.6 0,42 10.1019.08A 1/2" - 8 12,7 0.50 20,6 0.81 27.6 4000 110.4 16000 90 3.5 0,52 10.1019.10A 5/8” - 10 16,0 0.63 23,7 0.93 25.0 3625 100.0 14500 100 3.9 0,63 10.1019.12A 3/4" - 12 19,0 0.75 27,7 1.09 21.5 3118 86.0 12472 120 4.7 0,80 10.1019.16A 1” - 16 25,4 1.00 35,8 1.41 16.5 2393 66.0 9572 150 5.9 1,22





Balflex BALPAC 3000 SAE 100R17

Balflex® ARMORGUARD BALPAC 3000 SAE 100R17 – 10.1017.--A



High pressure, single or double steel braid reinforced hydraulic hose


Outer tube:


Temperature range:

Couplings:

seamless oil resistant synthetic rubber 1 high tensile steel wire braid on sizes 1/4", 5/16”, 3/8” and 1/2" and 2 braids on sizes 5/8”, 3/4" and 1” black, oil, weather and VERY HIGH abrasion resistant synthetic rubber 4: 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF); Intermittent service: + 120ºC (+ 248ºF) Max. temperature recommended for water base hydraulic fluids: + 70ºC (+ 158ºF) Max. temperature recommended for air: + 60ºC (+ 140ºF) Balflex

® crimped fittings series 23 with ferrules series 20.204 (2 wires) & 20.205 (1 wire).

Multicrimp P23 serie

part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


1 Wire Braid

10.1017.04A 1/4" - 4 6,3 0.25 12,7 0.50 22.5 3260 90.0 13040 51 2.0 0.22 10.1017.05A 5/16” - 5 8,0 0.31 15,0 0.59 21.0 3000 84.0 12000 60 2.4 0,27 10.1017.06A 3/8” - 6 9,5 0.38 16,5 0.65 21.0 3000 84.0 12000 64 2.5 0.34 10.1017.08A 1/2" - 8 12,7 0.50 20,8 0.82 21.0 3000 84.0 12000 89 3.5 0.42

2 Wire Braid

10.1017.10A 5/8” - 10 15,9 0.63 24,7 0.97 25.0 3625 100.0 14500 102 4.0 0.51 10.1017.12A 3/4" - 12 19,0 0.75 28,6 1.13 21.5 3120 86.0 12480 122 4.8 0.63 10.1017.16A 1” - 16 25,4 1.00 36,6 1.48 20.7 3000 82.8 12000 152 6.0 1.00






Balflex BALPAC DIN EN 1SC

Balflex® ARMORGUARD BALPAC DIN EN 857 1SC 10.1017.--A / 10.1018.--A




Inner tube:



Temperature range:

Couplings:

seamless oil resistant synthetic rubber 1 high tensile steel wire braid black, oil, weather and VERY HIGH abrasion resistant synthetic rubber 4 : 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF); Intermittent service: + 120ºC (+ 248ºF) Max. temperature recommended for water base hydraulic fluids: + 70ºC (+ 158ºF) Max. temperature recommended for air: + 60ºC (+ 140ºF) Balflex


part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1017.

10.1017.04A 1/4" - 4 6,3 0.25 12,7 0.50 22.5 3260 90.0 13040 51 2.0 0.22 10.1017.05A 5/16” - 5 8,0 0.31 15,0 0.59 21.0 3000 84.0 12000 60 2.4 0,27 10.1017.06A 3/8” - 6 9,5 0.38 16,5 0.65 21.0 3000 84.0 12000 64 2.5 0.34 10.1017.08A 1/2" - 8 12,7 0.50 20,8 0.82 21.0 3000 84.0 12000 89 3.5 0.42

10.1018.

10.1018.10A 5/8” - 10 15,9 0.63 23.0 0.90 13.0 1885 52.0 7540 102 4.0 0.51 10.1018.12A 3/4" - 12 19,0 0.75 26.7 1.05 10.5 1523 42.0 6090 122 4.8 0.63 10.1018.16A 1” - 16 25,4 1.00 34.9 1.37 8.8 1276 35.2 5104 152 6.0 1.00






Balflex BALPAC PREMIUM DIN EN 2SC

Balflex® ARMORGUARD BALPAC PREMIUM DIN EN 857 2SC 10.1019.--A




Inner tube :

Reinforcement : Outer tube :

Safety factor : Application :

Temperature range :

Couplings :

seamless oil resistant synthetic rubber 2 high tensile steel wire braid black, oil, weather and VERY HIGH abrasion resistant synthetic rubber 4 : 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF); Intermittent service: + 120ºC (+ 248ºF) Max. temperature recommended for water base hydraulic fluids: + 70ºC (+ 158ºF) Max. temperature recommended for air: + 60ºC (+ 140ºF) Balflex


part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1019.04A 1/4" - 4 6,3 0.25 13,3 0.52 40.0 5800 160.0 23200 50 2.0 0.27 10.1019.05A 5/16” - 5 8,0 0.31 15,0 0.59 35.0 5075 140.0 20300 57 2.2 0,30 10.1019.06A 3/8” - 6 9,5 0.38 17,1 0.67 33.0 4785 132.0 19140 65 2.6 0.42 10.1019.08A 1/2" - 8 12,7 0.50 20,6 0.81 27.6 4000 110.4 16000 90 3.5 0.52 10.1019.10A 5/8” - 10 15,9 0.63 23,7 0.93 25.0 3625 100.0 14500 100 3.9 0.63 10.1019.12A 3/4" - 12 19,0 0.75 27,7 1.09 21.5 3118 86.0 12472 120 4.7 0.80 10.1019.16A 1” - 16 25,4 1.00 35,8 1.41 16.5 2393 66.0 9572 150 5.9 1.22






Balflex BALMASTER SAE 100R12

Balflex® ARMORGUARD BALMASTER EN 856 R12 / SAE 100R12 10.1012.--A



High pressure, four steel wire spirals reinforced hydraulic hose

Inner tube:



Temperature range:

Couplings:

seamless oil resistant synthetic rubber 4 spirals of high tensile steel wire black, oil, weather and VERY HIGH abrasion resistant synthetic rubber 4: 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF); Intermittent service: + 120ºC (+ 248ºF) Max. temperature recommended for water base hydraulic fluids: + 70ºC (+ 158ºF) Max. temperature recommended for air: + 60ºC (+ 140ºF) Balflex

® crimped fittings 23 or 24 series with ferrules 20 serie

part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1012.06A 3/8” - 6 9,5 0.38 20,3 0.80 27.6 4000 110.0 16000 125 5.0 0,80 10.1012.08A 1/2" - 8 12,7 0.50 23,6 0.93 27.6 4000 110.0 16000 180 7.0 1,15 10.1012.10A 5/8” - 10 16,0 0.63 27,4 1.08 27.6 4000 110.0 16000 205 8.0 1,26 10.1012.12A 3/4" - 12 19,0 0.75 30,7 1.21 27.6 4000 110.0 16000 240 9.5 1,44 10.1012.16A 1” - 16 25,4 1.00 38,1 1.50 27.6 4000 110.0 16000 305 12.0 2,15 10.1012.20A 1.1/4” - 20 32,0 1.25 47,0 1.85 20.7 3000 82.7 12000 420 16.5 2,75 10.1012.24A 1.1/2” - 24 38,0 1.50 53,6 2.11 17.2 2500 69.0 10000 510 20.0 3,35 10.1012.32A 2” - 32 50,8 2.00 66,8 2.63 17.2 2500 69.0 10000 635 25.0 4,60






Balflex BALMASTER DIN EN 856 4SP

Balflex® ARMORGUARD BALMASTER EN 856 4SP – 10.1008.--A

According to ISO 3862 / EN 856 type 4SP



Inner tube:



Temperature range:

Couplings:

seamless oil resistant synthetic rubber 4 spirals of high tensile steel wire black, oil, weather and VERY HIGH abrasion resistant synthetic rubber 4: 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF); Intermittent service: + 120ºC (+ 248ºF) Max. temperature recommended for water base hydraulic fluids: + 70ºC (+ 158ºF) Max. temperature recommended for air: + 60ºC (+ 140ºF) Balflex


part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1008.04A 1/4" - 4 6,6 0.26 17,9 0.70 50.0 7250 200.0 29000 120 4.7 0,70 10.1008.06A 3/8” - 6 9,5 0.38 21,4 0.84 44.5 6453 178.0 25812 130 5.1 0,80 10.1008.08A 1/2" - 8 12,7 0.50 24,6 0.97 41.5 6018 166.0 24072 180 7.1 1,15 10.1008.10A 5/8” - 10 16,0 0.63 28,2 1.11 35.0 5075 140.0 20300 225 8.9 1,26 10.1008.12A 3/4" - 12 19,0 0.75 32,2 1.27 35.0 5075 140.0 20300 280 11.0 1,44 10.1008.16A 1” - 16 25,4 1.00 39,7 1.56 28.0 4060 112.0 16240 355 14.0 2,15 10.1008.20A 1.1/4” - 20 32,0 1.25 50,8 2.00 21.0 3045 84.0 12180 460 18.1 2,75 10.1008.24A 1.1/2” - 24 38,0 1.50 57,2 2.25 18.5 2683 74.0 10732 560 22.0 3,35 10.1008.32A 2” - 32 50,8 2.00 69,8 2.75 16.5 2393 66.0 9572 710 28.0 4,60






Balflex POWERSPIR DIN EN 856 4SH

Balflex® ARMORGUARD POWERSPIR EN 856 4SH – 10.1009.--A

According to ISO 3862 / EN 856 type 4SH



Inner tube:



Temperature range:

Couplings:

seamless oil resistant synthetic rubber 4 spirals of very high tensile steel wire black, oil, weather and VERY HIGH abrasion resistant synthetic rubber 4: 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF); Intermittent service: + 120ºC (+ 248ºF) Max. temperature recommended for water base hydraulic fluids: + 70ºC (+ 158ºF) Max. temperature recommended for air: + 60ºC (+ 140ºF) Balflex

® crimped fittings series 26 with ferrules 20.406. (3/4” and 1”) and 20.405. (1.1/4”,

1.1/2” and 2”) series

part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1009.12A 3/4" - 12 19,0 0.75 32,2 1.27 42.0 6090 168.0 24360 280 11.0 1,56 10.1009.16A 1” - 16 25,4 1.00 38,7 1.52 38.0 5510 152.0 22040 340 13.4 2,09 10.1009.20A 1.1/4” - 20 32,0 1.25 45,5 1.79 32.5 4713 130.0 18852 460 18.1 2,57 10.1009.24A 1.1/2” - 24 38,0 1.50 53,5 2.11 29.0 4205 116.0 16820 560 22.0 3,44 10.1009.32A 2” - 32 50,8 2.00 68,1 2.68 25.0 3625 100.0 14500 700 27.6 4,90

* On sizes – 12 (3/4”) and – 16 (1”) the Balflex





® POWERSPIR DIN EN 856 4SH and SAE 100R13 hose are the same







Balflex® ARMORGUARD POWERSPIR SAE 100R13 – 5000PSI 10.1009.--A * - 10.1014.--A




Inner tube:



Temperature range:

Couplings:

seamless oil resistant synthetic rubber 4 or 6 spirals of high tensile steel wire black, oil, weather and VERY HIGH abrasion resistant synthetic rubber 4: 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF); Intermittent service: + 120ºC (+ 248ºF) Max. temperature recommended for water base hydraulic fluids: + 70ºC (+ 158ºF) Max. temperature recommended for air: + 60ºC (+ 140ºF) Balflex

® crimped fittings series 26 with ferrules 20.406 serie

part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1009.12A * 3/4" - 12 19,0 0.75 32,2 1.27 42.0 6090 168.0 24360 280 11.0 1,56 10.1009.16A * 1” - 16 25,4 1.00 38,7 1.52 38.0 5510 152.0 22040 340 13.4 2,09 10.1014.20A 1.1/4” - 20 32,0 1.25 49,8 1.96 34.5 5000 138.0 20000 420 16.5 3,90 10.1014.24A 1.1/2” - 24 38,0 1.50 57,4 2.26 34.5 5000 138.0 20000 500 20.0 4,96 10.1014.32A 2” - 32 50,8 2.00 71,1 2.80 34.5 5000 138.0 20000 635 25.0 7,09


100R13 hose is of 4 steel wire spirals on sizes – 12 (3/4”) and – 16 (1”) and of 6 steel wire spirals on sizes – 20 (1.1/4”), – 24 (1.1/2”) and – 32 (2”). * On sizes – 12 (3/4”) and – 16 (1”) the Balflex










Balflex® ARMORGUARD POWERSPIR SAE 100R15 – 6000PSI 10.1016.--A




Inner tube:



Temperature range:

Couplings:

seamless oil resistant synthetic rubber 4 or 6 spirals of high tensile steel wire black, oil, weather and VERY HIGH abrasion resistant synthetic rubber 4: 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF); Intermittent service: + 120ºC (+ 248ºF) Max. temperature recommended for water base hydraulic fluids: + 70ºC (+ 158ºF) Max. temperature recommended for air: + 60ºC (+ 140ºF) Balflex


part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1016.06A 3/8” - 6 9,5 0.38 23,3 0.92 41.4 6000 165.5 24000 153 6.0 0,75 10.1016.08A 1/2" - 8 12,7 0.50 26,8 1.06 41.4 6000 165.5 24000 203 8.0 0,89 10.1009.12A* 3/4" - 12 19,0 0.75 36,1 1.42 41.4 6000 165.5 24000 267 10.5 1,56 10.1016.16A 1” - 16 25,4 1.00 42,9 1.69 41.4 6000 165.5 24000 330 13.0 2,10 10.1016.20A 1.1/4” - 20 32,0 1.25 51,5 2.03 41.4 6000 165.5 24000 445 17.5 3,65 10.1016.24A 1.1/2” - 24 38,0 1.50 59,6 2.32 41.4 6000 165.5 24000 533 21.0 5,00


100R15 hose is of 4 steel wire spirals on sizes – 6 (3/8”), 8 (1/2”), – 12 (3/4”) and – 16 (1”) and of 6 steel wire spirals on sizes – 20 (1.1/4”) and – 24 (1.1/2”).

According to ISO 3862 / SAE J517 type R15 doesn’t exist the size – 32 (2”). * On size – 12 (3/4”) the Balflex

® POWERSPIR DIN EN 856 4SH and SAE 100R15 hoses are the same






Balflex EN 855 R7 / SAE 100R7

Balflex® EN 855 R7 / SAE 100R7 – 10.1030.


High pressure, synthetic polyester braid reinforced thermoplastic hydraulic hose




Couplings:

seamless oil resistant thermoplastic 1 high tensile polyester braid black, oil and weather resistant thermoplastic 4: 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF) Max. temperature recommended for water base hydraulic fluids: + 65ºC (+ 149ºF) Balflex


part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1030.02 1/8” - 2 3,0 0.12 8,1 0.32 28.0 4060 112.0 16240 50 2.00 0,05 10.1030.03 3/16” - 3 4,8 0.19 10,3 0.41 21.0 3045 84.0 12180 75 2.95 0,07 10.1030.04 1/4" - 4 6,3 0.25 12,4 0.49 19.0 2755 76.0 11020 100 3.94 0,09 10.1030.05 5/16” - 5 8,0 0.31 14,2 0.56 19.0 2755 76.0 11020 114 4.49 0,13 10.1030.06 3/8” - 6 9,5 0.38 15,7 0.62 16.0 2320 64.0 9280 127 5.00 0,16 10.1030.08 1/2" - 8 12,7 0.50 19,3 0.76 14.0 2030 56.0 8120 178 7.00 0,22 10.1030.10 5/8” - 10 16,0 0.63 23,1 0.91 10.5 1523 42.0 6092 203 7.99 0,28 10.1030.12 3/4" - 12 19,0 0.75 26,4 1.04 9.0 1305 36.0 5220 254 10.00 0,33 10.1030.16 1” - 16 25,4 1.00 33,3 1.31 7.0 1015 28.0 4060 305 12.00 0,40

Note: Size - 2 (1/8”) not included in the standards.





Balflex EN 855 R7 / SAE 100R7 TWIN

Balflex® EN 855 R7 / SAE 100R7 TWIN – 10.1034.


High pressure, synthetic polyester braid reinforced thermoplastic hydraulic twin line hose

Inner tube:



Temperature range:

Couplings:

seamless oil resistant thermoplastic 1 high tensile polyester braid black, oil and weather resistant thermoplastic 4: 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF) Max. temperature recommended for water base hydraulic fluids: + 65ºC (+ 149ºF) Balflex


part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1034.03 3/16” - 3 4,8 0.19 10,3 0.41 21.0 3045 84.0 12180 75 2.95 0,07 10.1034.04 1/4" - 4 6,3 0.25 12,4 0.49 19.0 2755 76.0 11020 100 3.94 0,09 10.1034.05 5/16” - 5 8,0 0.31 14,2 0.56 19.0 2755 76.0 11020 114 4.49 0,13 10.1034.06 3/8” - 6 9,5 0.38 15,7 0.62 16.0 2320 64.0 9280 127 5.00 0,16 10.1034.08 1/2" - 8 12,7 0.50 19,3 0.76 14.0 2030 56.0 8120 178 7.00 0,22 10.1034.10 5/8” - 10 16,0 0.63 23,1 0.91 10.5 1523 42.0 6092 203 7.99 0,28 10.1034.12 3/4" - 12 19,0 0.75 26,4 1.04 9.0 1305 36.0 5220 254 10.00 0,33 10.1034.16 1” - 16 25,4 1.00 33,3 1.31 7.0 1015 28.0 4060 305 12.00 0,40





Balflex EN 855 R7/SAE 100R7NONCONDUCTIVE

Balflex® EN 855 R7 / SAE 100R7 NON CONDUCTIVE – 10.1030.L

According to ISO 3949 / EN 855 type R7 / SAE J517 type SAE 100R7 High pressure, synthetic fiber braid reinforced thermoplastic NON CONDUCTIVE hydraulic hose

Inner tube:



Temperature range:

Couplings:

seamless oil resistant thermoplastic 1 high tensile polyester braid orange, oil and weather resistant polyurethane 4: 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF) Max. temperature recommended for water base hydraulic fluids: + 65ºC (+ 149ºF) Balflex


part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1030.02L 1/8” - 2 3,0 0.12 8,1 0.32 28.0 4060 112.0 16240 50 2.00 0,05 10.1030.03L 3/16” - 3 4,8 0.19 10,3 0.41 21.0 3045 84.0 12180 75 2.95 0,07 10.1030.04L 1/4" - 4 6,3 0.25 12,4 0.49 19.0 2755 76.0 11020 100 3.94 0,09 10.1030.05L 5/16” - 5 8,0 0.31 14,2 0.56 19.0 2755 76.0 11020 114 4.49 0,13 10.1030.06L 3/8” - 6 9,5 0.38 15,7 0.62 16.0 2320 64.0 9280 127 5.00 0,16 10.1030.08L 1/2" - 8 12,7 0.50 19,3 0.76 14.0 2030 56.0 8120 178 7.00 0,22 10.1030.10L 5/8” - 10 16,0 0.63 23,1 0.91 10.5 1523 42.0 6092 203 7.99 0,28 10.1030.12L 3/4" - 12 19,0 0.75 26,4 1.04 9.0 1305 36.0 5220 254 10.00 0,33 10.1030.16L 1” - 16 25,4 1.00 33,3 1.31 7.0 1015 28.0 4060 305 12.00 0,40

Note: Size - 2 (1/8”) not included in the standards.





Balflex EN 855 R7/SAE 100R7NONCONDUCTIVE TWIN

Balflex® EN 855 R7 / SAE 100R7 NON CONDUCTIVE TWIN – 10.1034.L


High pressure, synthetic fiber braid reinforced thermoplastic NON CONDUCTIVE hydraulic twin line hose

Inner tube:



Temperature range:

Couplings:

seamless oil resistant thermoplastic 1 high tensile polyester braid orange, oil and weather resistant polyurethane 4: 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF) Max. temperature recommended for water base hydraulic fluids: + 65ºC (+ 149ºF) Balflex


part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1034.03L 3/16” - 3 4,8 0.19 10,3 0.41 21.0 3045 84.0 12180 75 2.95 0,07 10.1034.04L 1/4" - 4 6,3 0.25 12,4 0.49 19.0 2755 76.0 11020 100 3.94 0,09 10.1034.05L 5/16” - 5 8,0 0.31 14,2 0.56 19.0 2755 76.0 11020 114 4.49 0,13 10.1034.06L 3/8” - 6 9,5 0.38 15,7 0.62 16.0 2320 64.0 9280 127 5.00 0,16 10.1034.08L 1/2" - 8 12,7 0.50 19,3 0.76 14.0 2030 56.0 8120 178 7.00 0,22 10.1034.10L 5/8” - 10 16,0 0.63 23,1 0.91 10.5 1523 42.0 6092 203 7.99 0,28 10.1034.12L 3/4" - 12 19,0 0.75 26,4 1.04 9.0 1305 36.0 5220 254 10.00 0,33 10.1034.16L 1” - 16 25,4 1.00 33,3 1.31 7.0 1015 28.0 4060 305 12.00 0,40





Balflex R7 SteelFlex

Balflex® R7 SteelFlex – 10.1031.

High pressure, wire steel braid reinforced thermoplastic hydraulic hose




Couplings:

seamless oil resistant thermoplastic 1 high tensile steel wire braid black, oil and weather resistant thermoplastic 4: 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF) Max. temperature recommended for water base hydraulic fluids: + 65ºC (+ 149ºF) Balflex


part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1031.02 1/8” - 2 3,0 0.12 6,9 0.27 35.0 5075 140.0 20300 25 1.00 0,10 10.1031.03 3/16” - 3 4,8 0.19 10,0 0.39 30.0 4350 120.0 17400 30 1.18 0,13 10.1031.04 1/4" - 4 6,3 0.25 11,9 0.47 27.5 3988 110.0 15952 40 1.57 0,17 10.1031.05 5/16” - 5 8,0 0.31 14,0 0.55 24.0 3480 96.0 13920 50 1.96 0,22 10.1031.06 3/8” - 6 9,5 0.38 16,0 0.63 22.0 3190 88.0 12790 60 2.36 0,26 10.1031.08 1/2" - 8 12,7 0.50 20,5 0.81 17.5 2538 70.0 10152 75 2.95 0,39 10.1031.10 5/8” - 10 16,0 0.63 23,3 0.92 14.0 2030 56.0 8120 110 4.33 0,41 10.1031.12 3/4" - 12 19,0 0.75 25,0 0.98 11.5 1668 46.0 6672 150 5.90 0,45 10.1031.16 1” - 16 25,4 1.00 32,5 1.28 10.0 1450 40.0 5800 230 9.06 0,62





Balflex R7 SteelFlex Twin

Balflex® R7 SteelFlex TWIN – 10.1035.

High pressure, wire steel braid reinforced thermoplastic hydraulic twin line hose

Inner tube:



Temperature range:

Couplings:

seamless oil resistant thermoplastic 1 high tensile steel wire braid black, oil and weather resistant thermoplastic 4: 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF) Max. temperature recommended for water base hydraulic fluids: + 65ºC (+ 149ºF) Balflex


part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1035.03 3/16” - 3 4,8 0.19 10,0 0.39 30.0 4350 120.0 17400 30 1.18 0,13 10.1035.04 1/4" - 4 6,3 0.25 11,9 0.47 27.5 3988 110.0 15952 40 1.57 0,17 10.1035.05 5/16” - 5 8,0 0.31 14,0 0.55 24.0 3480 96.0 13920 50 1.96 0,22 10.1035.06 3/8” - 6 9,5 0.38 16,0 0.63 22.0 3190 88.0 12790 60 2.36 0,26 10.1035.08 1/2" - 8 12,7 0.50 20,5 0.81 17.5 2538 70.0 10152 75 2.95 0,39 10.1035.10 5/8” - 10 16,0 0.63 23,3 0.92 14.0 2030 56.0 8120 110 4.33 0,41 10.1035.12 3/4" - 12 19,0 0.75 25,0 0.98 11.5 1668 46.0 6672 150 5.90 0,45 10.1035.16 1” - 16 25,4 1.00 32,5 1.28 10.0 1450 40.0 5800 230 9.06 0,62






Balflex® EN 855 R8 / SAE 100R8 – 10.1032.


High pressure, double polyester braid reinforced thermoplastic hydraulic hose




Couplings:

seamless oil resistant thermoplastic 2 high tensile polyester braids black, oil and weather resistant thermoplastic 4: 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF) Max. temperature recommended for water base hydraulic fluids: + 65ºC (+ 149ºF) Balflex

® crimped fittings 23 serie with ferrules 20 serie

part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1032.03 3/16” - 3 4,8 0.19 12,4 0.49 35.0 5075 140.0 20300 35 1.38 0,09 10.1032.04 1/4" - 4 6,3 0.25 16,1 0.63 35.0 5075 140.0 20300 50 1.96 0,10 10.1032.05 5/16” - 5 8,0 0.31 16,7 0.66 29.0 4205 116.0 16820 60 2.36 0,13 10.1032.06 3/8” - 6 9,5 0.38 18,5 0.73 28.0 4060 112.0 16240 80 3.15 0,18 10.1032.08 1/2" - 8 12,7 0.50 22,6 0.89 24.5 3553 98.0 14212 95 3.74 0,22 10.1032.10 5/8” - 10 16,0 0.63 25,6 1.01 19.0 2755 76.0 11020 125 4.92 0,31 10.1032.12 3/4" - 12 19,0 0.75 28,9 1.14 15.5 2250 62.0 9000 150 5.90 0,36 10.1032.16 1” - 16 25,4 1.00 36,1 1.42 14.0 2030 56.0 8120 200 7.87 0,51






Balflex® EN 855 R8 / SAE 100R8 – 10.1033.


High pressure, single aramidic braid reinforced thermoplastic hydraulic hose




Couplings:

seamless oil resistant thermoplastic 1 high tensile aramidic fiber braid black, oil and weather resistant thermoplastic 4: 1 petroleum base hydraulic fluids - 40ºC (- 40ºF) + 100ºC (+ 212ºF) Max. temperature recommended for water base hydraulic fluids: + 65ºC (+ 149ºF) Balflex


part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1033.03 3/16” - 3 4,8 0.19 10,3 0.41 35.0 5075 140.0 20300 35 1.38 0,09 10.1033.04 1/4" - 4 6,3 0.25 11,7 0.46 35.0 5075 140.0 20300 50 1.96 0,10 10.1033.05 5/16” - 5 8,0 0.31 14,2 0.55 30.0 4350 120.0 17400 60 2.36 0,13 10.1033.06 3/8” - 6 9,5 0.38 15,7 0.62 28.0 4060 112.0 16240 80 3.15 0,18 10.1033.08 1/2" - 8 12,7 0.50 19,3 0.76 24.5 3553 98.0 14212 95 3.74 0,22 10.1033.10 5/8” - 10 16,0 0.63 23,1 0.91 20.0 2900 80.0 11600 125 4.92 0,31 10.1033.12 3/4" - 12 19,0 0.75 26,4 1.04 16.5 2393 66.0 9572 150 5.90 0,36 10.1033.16 1” - 16 25,4 1.00 33,3 1.31 14.0 2030 56.0 8120 200 7.87 0,51

Balflex® Ultraflex R9 – 10.1038.

High pressure, single aramidic braid reinforced thermoplastic hydraulic hose




Couplings:



part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1038.06 3/8” - 6 9,5 0.38 16,0 0.63 38.0 5510 152.0 22040 80 3.15 0,18 10.1038.08 1/2" - 8 12,7 0.50 20,3 0.80 34.5 5000 138.0 20000 95 3.74 0,22





Balflex EN 855 R8 / SAE 100R8 TWIN

Balflex® EN 855 R8 / SAE 100R8 TWIN – 10.1036.


High pressure, single aramidic braid reinforced thermoplastic hydraulic twin line hose




Couplings:



part

number

Ø nom.

dash size

Ø internal

Ø external

working pressure

min. burst pressure

min. bend

radius

weight


10.1036.03 3/16” - 3 4,8 0.19 10,3 0.41 35.0 5075 140.0 20300 35 1.38 0,18 10.1036.04 1/4" - 4 6,3 0.25 12,4 0.49 35.0 5075 140.0 20300 50 1.96 0,20 10.1036.05 5/16” - 5 8,0 0.31 14,2 0.55 30.0 4350 120.0 17400 60 2.36 0,26 10.1036.06 3/8” - 6 9,5 0.38 15,7 0.62 28.0 4060 112.0 16240 80 3.15 0,36 10.1036.08 1/2" - 8 12,7 0.50 19,3 0.76 24.5 3553 98.0 14212 95 3.74 0,44 10.1036.10 5/8” - 10 16,0 0.63 23,1 0.91 20.0 2900 80.0 11600 125 4.92 0,62 10.1036.12 3/4" - 12 19,0 0.75 26,4 1.04 16.5 2393 66.0 9572 150 5.90 0,72 10.1036.16 1” - 16 25,4 1.00 33,3 1.31 14.0 2030 56.0 8120 200 7.87 1,02





Balflex Flat HDPE Spring Guard

Balflex® HYDRAULIC AND INDUSTRIAL HOSE FLAT GUARD – 11.103.

High Density Polyethylene Protection Spring Guard

Raw Material : Color :

Temperature range : Application :

high density polyethylene resistant to abrasion and UV rays black or yellow - 20ºC (- 4ºF) + 95ºC (- 203ºF) protection of external rubber layer of hydraulic and industrial hoses, against the early wearing due to abrasion

Part number

Ø nom

mm

11.103.012 12

11.103.013 13

11.103.016 16

11.103.020 20

11.103.024 24

11.103.025 25

11.103.027 27

11.103.030 30

11.103.032 32

11.103.035 35

11.103.044 44

11.103.050 50

11.103.055 55

11.103.070 70

11.103.100 100





Balflex Nylon Protective Guard

Balflex® Nylon Protective Guard

Textile Hose Protection Guard

Easy-to-install, textile protection guard

When used in hoses, protective guard protects people nearby a breaking hose and meets the requirements of standards EN 12999 and EN ISO 3457.

The recommended temperature range is - 40ºC (- 40ºF) + 80°C(+ 176ºF) UV-protected and has a very low conductivity of electricity.

Abrasion resistance very good.

Balflex

® Part Number Flat I.D. (mm) Round I.D. (mm)

11.400.027 27 17 11.400.031 31 20 11.400.036 36 23 11.400.039 39 25 11.400.042 42 27 11.400.049 49 31 11.400.050 52 33 11.400.054 54 36 11.400.063 63 40 11.400.069 69 44 11.400.074 74 47 11.400.083 83 53 11.400.086 86 55 11.400.094 94 60 11.400.104 104 66 11.400.115 115 73 11.400.146 146 93 11.400.176 176 112 11.400.202 202 127





Documents

Balflex Hydraulic Hoses - Deutsche Messe AGdonar.messe.de/exhibitor/hannovermesse/2017/S... · Balflex Hydraulic Hoses Balflex® Hydraulic Hoses Balflex® hydraulic hoses are produced