2
Bag Box w/Mini Notecards Chiaki Haverstick, Stampin’ Up! demonstrator (714) 550-9342 e-mail: [email protected] www.chiaki.stampinup.net www.stampingpro.com Artwork © Stampin’ Up!® 1990-2009 Supplies: 1/2 sheet Designer Series Paper (6” x 12”) 1-2 sheets of coordinating cardstock for bag trim and lay- ering on notecards 6 3” x 6” pieces of cardstock for Mini Notecards 6 SU! Mini Envelopes (3-1/8” square) 1 3” x 4-1/2” piece of cardstock for bottom of bag 12” Paper Cutter w/ both cutting and scoring blades Sticky Strip, Snail Adhesive, Dimensionals SU! Eyelet Border punch, Tab punch Assorted Stamps, Stamp Pads and additional punches Mini Brads, Ribbons, and other embellishments 1-1/23” 3” 1” 11-1/21” 2-1/21-1/22-1/22-1/23-1/2Directions: Step 1: Cut the 6” x 12” piece of Designer Series Paper as shown in the diagram below and set the pieces aside. Step 2: Score the 3” x 4-1/2” square piece of cardstock at 1/2” on all four sides. Make a cut from the outside edge to the inner score mark on the 2 opposite sides. Fold the flaps up and use sticky strip to assemble the base of bag. Step 3: Place Sticky Strip along the bottom (11-1/2”) edge as well as the right edge of the 3-1/2” x 11-1/2” piece of DSP. Step 4: Cut s 1” x 11-1/2” strip of coordinating cardstock and use Eyelet Border punch along the strip for purse trim. Place Place Sticky Strip along entire length of the trim and adhere the bottom of the 4” x 8” 3-1/2” x 11-1/2” piece of DSP as shown. Step 5: Take the 3-1/2” x 11-1/2” piece of DSP and begin adhering it to the boxbase starting in the middle of one of the longer sides. The DSP will overlap to complete the bag. Step 6: Punch 2 pieces of coordinating cardstock using the Tab punch. Adhere tabs to each side of the bagbox using Sticky Strip. Punch holes through each tab so you can close with ribbon later. Step 6: Fold the 3” x 6” pieces of cardstock in half and embellish these mini notecards using the other cut pieces of DSP, additional cardstock for layering, ribbon, stamps and punches as desired (see sample photos for ideas). Place the completed cards and envelopes in the bagbox, tie tabs together with a ribbon and you’re done! Example for scoring and cutting of the bottom of bag (this is a 3” x 4-1/2” piece of cardstock) dotted line = score solid line = cut

Bag Box w/Mini Notecards - StampingPro.comstampingpro.com/wp-content/uploads/bagboxwithmininotecards.pdf · Bag Box w/Mini Notecards Chiaki Haverstick, Stampin’ Up! demonstrator

  • Upload
    buidieu

  • View
    217

  • Download
    0

Embed Size (px)

Citation preview

Bag Box w/Mini Notecards

Chiaki Haverstick, Stampin’ Up! demonstrator(714) 550-9342 e-mail: [email protected] www.stampingpro.com

Artwork © Stampin’ Up!® 1990-2009

Supplies:

1/2 sheet Designer Series Paper (6” x 12”)1-2 sheets of coordinating cardstock for bag trim and lay-ering on notecards6 3” x 6” pieces of cardstock for Mini Notecards6 SU! Mini Envelopes (3-1/8” square)1 3” x 4-1/2” piece of cardstock for bottom of bag12” Paper Cutter w/ both cutting and scoring bladesSticky Strip, Snail Adhesive, DimensionalsSU! Eyelet Border punch, Tab punchAssorted Stamps, Stamp Pads and additional punchesMini Brads, Ribbons, and other embellishments

1-1/2”

3” 3”1”

11-1/2”

1”

2-1/2”

1-1/2”

2-1/2”

2-1/2”

3-1/2”

Directions:

Step 1: Cut the 6” x 12” piece of Designer Series Paper as shown in the diagram below and set the pieces aside. Step 2: Score the 3” x 4-1/2” square piece of cardstock at 1/2” on all four sides. Make a cut from the outside edge to the inner score mark on the 2 opposite sides. Fold the flaps up and use sticky strip to assemble the base of bag. Step 3: Place Sticky Strip along the bottom (11-1/2”) edge as well as the right edge of the 3-1/2” x 11-1/2” piece of DSP. Step 4: Cut s 1” x 11-1/2” strip of coordinating cardstock and use Eyelet Border punch along the strip for purse trim. Place Place Sticky Strip along entire length of the trim and adhere the bottom of the 4” x 8” 3-1/2” x 11-1/2” piece of DSP as shown. Step 5: Take the 3-1/2” x 11-1/2” piece of DSP and begin adhering it to the boxbase starting in the middle of one of the longer sides. The DSP will overlap to complete the bag. Step 6: Punch 2 pieces of coordinating cardstock using the Tab punch. Adhere tabs to each side of the bagbox using Sticky Strip. Punch holes through each tab so you can close with ribbon later. Step 6: Fold the 3” x 6” pieces of cardstock in half and embellish these mini notecards using the other cut pieces of DSP, additional cardstock for layering, ribbon, stamps and punches as desired (see sample photos for ideas). Place the completed cards and envelopes in the bagbox, tie tabs together with a ribbon and you’re done!

Example for scoring and

cutting of the bottom of bag

(this is a 3” x 4-1/2” piece of cardstock)

dotted line = scoresolid line = cut

Artwork © Stampin’ Up!® 1990-2009