Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
B870P PLUS
ENGLISH
- 1 -
Plastic Cover
(H1)BottleHolder
(J1)Screw (J2)Washer (J3)Spring washer
(H2)Water Bottle
(G)
ASSEMBLY FOR FRONT STABILIZERAttach the front stabilizer(C) to the bracket at the front
of the main frame(A). Insert 2pcs bolt(J1) and 2pcs
washer(J2) ,2pcs spring washer(J3) through the front
stabilizer(C) to attach with the main frame(A).
Then, fix the bolts tightly.
ASSEMBLY FOR REAR STABILIZERAttach the rear stabilizer(B) to the
bracket at the front of the
main frame(A). Insert 2pcs bolt(J1)
and 2pcs washer(J2), 2pcs spring
washer(J3) through the rear
stabilizer(B) to attach with the
main frame(A). Then, fix the
bolts tightly.
- 2 -
A
C
J1J3 J2
J1J3
J2
B
A
ASSEMBLY FOR CENTRALSUPPORT TUBE
STEP 1.TAKE OFF THE BOLT(A5),
SPRING WASHERS(A34) AND WASHERS(A4) FORM THE MAIN FRAME(A) BEFORE
ASSEMBLY.
STEP 2.PUT THE UPPER CENTRAL TUBE
(L) THROUGH DECORATION
COVER(M) FIRST AND AFTER
THE CABLE CONNECTED WELL
POSITION THE COVER(M) UNTILL
THE BUTTON.
STEP 4.ASSEMBLE SUPPORT TUBE(L) WITH
THE MAIN FRAME(A) BY BOLTS(A5),
SPRING WASHERS(A34) AND WASHERS(A4).
ATTENTION:TAKE CARE WHEN PUSHING THE TUBES TOGETHER THAT THE CABLES AND WIRES ARE NOT PINCHED.
STEP 3.CONNECT THE SENSOR
WIRE(A7) AND THE
COMPUTER CABLE(L1).
- 3 -
L1
A7
A34
- 4 -
ASSEMBLY FOR HANDLE BAR First,remove the nut(L2) from the handle bar housing.
Put the handle bar(E) into the handle bar housing and secure it by nut(L2).Then Slide the sensor wires(L1 & E3) as shown on (view A).
L
L2
ASSEMBLY THE COMPUTERRemove the nut (K1) from the back side of computer(K).Connect the sensor wires(E3 & L1) with computer wires and put the computer on the computer housing(H).Then secure the computer on the computerhousing by nut(K1).
K
E3
L1
E3
L1
H
K1
A
D2
A22
ASSEMBLY SADDLE SUPPORT TUBE & SADDLE WITH MAIN FRAMESTEP 1:Loosen the knob(A22) and keep on pulling it. Then, insert the saddle
support tube(D) into the main frame(A).Release the knob(A22) after
the saddle support tube is equipped appropriately.
Attention:
Please make sure the knob has been equipped exactly into the adjusting hole
of the saddle support tube(D).
Loosen the saddle adjustment
Handle(D2) and move the saddle until
it is at a comfortable distance.
Tighten the saddle adjustment knob
to lock the saddle basement.
ADJUST THE SADDLE
STEP 2:
Equip the saddle(G) with the seat basement(D1) by the preinstallednuts(G1) and washer(G2) on the bottom of the saddle(G).
- 5 -
6
6
6
6
H1
H3
ASSEMBLY FOR BOTTLE HOLDER
Release the screw(H3) from thesupport tube(L) first, then assembly the water bottle holder(H1) on thesupport tube(L) and secure it byscrew(H3).Then put the water bottle (H2) into the bottle holder(H1).
G1
G2
D1
ASSEMBLY PEDAL WITH MAIN FRAMEStep 1.Equip the left pedal(F1-L) with the crank by anti-clockwise direction.
Step 2.Equip the right pedal(F2-R) with the crank by clockwise direction.
HOW TO MOVE THE MACHINEStep1. Hold the handle bar and push down the handle bar.
Step2. You can move the machine easily by the transportation wheel on the
front stabilizer.
- 6 -
- 7 -
A Main Frame Chain Cover(L) 1
A1 Sensor Housing 10
A3 Screw 1
A2 Sensor
Chain Cover(R) 1A4 Washer
1A5 Screw 4
4
4
Rear Stabilizer 1
A6 Motor 1
End Cap
Adjusting Screw M8* 29*42.5
Adjusting End
2
4
4
A7 Sensor Wire
Front Stabilizer 1
A8 Driving Wheel
End Cap 2
A8-1 Magnet
Transportation Wheel 2
A9 Axle
Screw 4
A9-1 Screw
Saddle Support Tube 1
A9-2
A9-3
Seat Basement 1
1
A10 Driving Belt
Knob
A11 Magnetic Wheel
Gap Block 1
A11-1 Nut(3t)
Screw M4
End cap
1
A11-2 Nut(9t)
A11-3 Magnetic Housing
Handle Bar 1
A11-4 Bolt 1
E1 End Cap 2
2
2
A11-5
A11-6
A11-7
A11-8
A11-9
A11-10
A11-11
A11-12
A11-13
Nut
Axle Center
Bearing(6000)
Pulley
Bearing(6003)
Bearing
Washer
Bearing(6300)
C Type Buckle
1
1
1
1
1
1
1
E2 Screw 4
A12 Spring 1
E3
Hand Pulse Sensor 2 E4 Spaced Ring 2
A13 Pressing Plate 1
A13-1 Plastics Washer
Washer
2
A13-2 Nut 1
F1 Pedal(L) 1
A13-3 Pressing Wheel 1
F1-1 Screw
1
A13-4 C Type Buckle 1
F1-2
Crank Cap 1
F2 Pedal(R) 1
F2-1
Screw 1
F2-2
Crank Cap 1
G
G1
G2
H1
H2
Saddle
Nut
Washer
Bottle Holder
Water Bottle
1
1
1 A18 Bearing 2
A20 Spring Screw
Washer
Spring Washer
4
4
4
A21
A22
A23
Knob
Gap Block
Spring
Computer 1A24 Plastic Pipe
Screw
Screw
4A26 Crank(L) 1
L Central 1 A27 Crank(R)
A28
A6-1
Upper Cover
A29
Computer Cable 1
A29-1 Screw
Screw
A30
A30-1
4
1
1
1
1
A31
A32
A33
A34
B
B1
B2
B3
C
1
C1
1
1
C2
1
C3
D
D1
1
D2
1
D3
3
2
2
2
D
D5
End capD6
4
11
E
1 J1
J2
J3
Screw 4J4
1
1
1
TENSION CABLE
A6-2 DC LINE
K1
K1
6
1
1
1
L1 L2
Upper Side Cover(R)
Rear Side Cover
A13-5
A13-6
Screw 1
1
A30-2 Screw 6
Nut 2M
H3
Plastic Cover 1
Upper Side Cover(L)
Nut
C Type Buckle
Spring Washer 4
P/N DESCRIPTION Q’TY P/N DESCRIPTION Q’TY
3
3
BUTTON FUNCTIONS
DISPLAY FUNCTIONS TIME Time will count up from 00:00 to maximum 99:00 with each increment
is 1 minute. SPEED Displays current training speed. Maximum speed is 99.9 KM/H or
ML/H. RPM Displays the Rotation Per Minute. Display range 0~100 RPM DISTANCE Accumulates total distance from 00:0 up to 99.9 KM or ML. The user
may preset target distance data by turning the UP/DOWN joggle wheel. Each incensement is 0.1KM or ML.
UP To make upward adjustment to each function data or increase training resistance.
DOWN To make downward adjustment to each function data or decrease training resistance.
ENTER To confirm all settings.
START/ STOP
RESET To reset current setting and have the monitor switch to initial training mode for selection. Press the RESET button for 2 seconds under standby mode for a Total Reset.
RECOVERY To active RECOVERY function.
To start or stop workout. Turn the START/ STOP joggle wheel under standby mode, it can be a quick start key to the Manual Program.
CALORIES Accumulates calories consumption during training from 0 to maximum 990 calories. Each unit for increase or decrease is 10 KCL. (This data is a rough guide for comparison of different exercise sessions which can not be used in medical treatment.)
PULSE User may set up target pulse from 0 - 30 to 230 WATTS Display current workout watts. Display range 0~999.
POWER ON 1. Connect power supply to the monitor or press the RESET button for 2 seconds, the LCD will display all segment with a long- beep sound for 2 seconds and display 78.0 in below (FIGURE 1 & 2). 2. User may turn the UP/DOWN joggle wheel to select User 1~4 and press ENTER for confirmation (FIGURE 3~4). And then preset user information for SEX, AGE, HEIGHT and WEIGHT. (FIGURE 4~7)
FIGURE 1 FIGURE 2 FIGURE 3 FIGURE 4
FIGURE 5 FIGURE 6 FIGURE 7 FIGURE 7 PROGRAMMING MODE
1. Program selections are MANUAL PROGRAM USER PROGRAM H.R.C. WATT (FIGURE 8~12)
2. Use UP/DOWN joggle wheel to select the program you want and press ENTER to confirm. Or press START/STOP button to start MANUAL mode immediately.
FIGURE 8 FIGURE 9 FIGURE 10 FIGURE 11
FIGURE 12 QUICK START IN MANUAL 1. Press ENTER to enter MANUAL program, and the screen is blinking (FIGURE 13). 2. Press START/STOP to start exercising. The resist level is adjustable during exercising
(FIGURE 14). 3. User can press START/ STOP to stop exercising
FIGURE 13 FIGURE 14
MANUAL MODE
1. After selecting MANUAL mode (FIGURE 13), user can use UP/DOWN joggle wheel to increase or decrease level (from 1 to 16) and press ENTER to confirm.
2. User may preset exercise data (TIME, DISTANCE, CALORIES, PULSE), and press START/STOP to start exercise. User can press RESET to return to the MANUAL setting
3. Level is adjustable during training.
FIGURE 13 FIGURE 14 FIGURE 15 FIGURE 16
FIGURE 17 FIGURE 18 FIGURE 19 FIGURE 20
USER SELECT U1-U4
PRESSRESET 3 SEC TO RESET
CLOCKWISE ORANTI-CLOCKWISE
MANUAL mode
PRESSENTER
CLOCKWISE ORANTI-CLOCKWISE
CLOCKWISE ORANTI-CLOCKWISE
PRESSENTER
PRESSENTER
CLOCKWISE ORANTI-CLOCKWISE
CLOCKWISE ORANTI-CLOCKWISE
PRESSENTER CLOCKWISE OR
ANTI-CLOCKWISECLOCKWISE OR
ANTI-CLOCKWISEPRESSENTER
PRESSENTER
FUNCTION SELECT
TIME
PULS
CALORIESDISTAN
CE
E
CLOCKWISE ORANTI-CLOCKWISE
PRESSENTER
START/STOP
FIGURE 21 FIGURE 22 FIGURE 23 FIGURE 24
PROGRAM MODE
1. After enter PROGRAM mode, user and turn the UP/DOWN joggle wheel to select program profile from P1 to P12, then press ENTER to confirm.
2. User can preset the TIME data then press START/STOP to start exercise. 3. After start training, TIME will be counted down. When the TIME is counted to 0, the
screen is flashing and the alarm is ringing. User can press any button to stop the alarm.
USER SELECT U1-U4
PRESSRESET 3 SEC TO RESET
CLOCKWISE ORANTI-CLOCKWISE
PROGRAM mode
PRESSENTER
CLOCKWISE ORANTI-CLOCKWISE
CLOCKWISE ORANTI-CLOCKWISE
PRESSENTER
PRESSENTER
CLOCKWISE ORANTI-CLOCKWISE
CLOCKWISE ORANTI-CLOCKWISE
PRESSENTER CLOCKWISE OR
ANTI-CLOCKWISEPRESSENTER
PRESSENTER
FUNCTION SELECT
TIME
CLOCKWISE ORANTI-CLOCKWISE
PRESSENTER
PROGRAM SELECT P1 to P12
P1P2
P3
P4
P5
P7P6P8
P9
P10
P11
P12
CLOCKWISE ORANTI-CLOCKWISE
to 0, the screen is flashing and the alarm is ringing. User can press any button to stop the alarm.
FIGURE 25 FIGURE 26 FIGURE 27 FIGURE 28
FIGURE 29
USER PROGRAM 1. After enter USER PROGRAM mode, the first column of the profile is blinking (FIGURE 25).
User may turn the joggle wheel to adjust the resistance level (FIGURE 26) to create his / her own profile.
2. After setting (from column 1 to column 20), user may hold on pressing MODE button for 2 seconds to quit profile setting and enter TIME setting.
3. While making the profile setting, user can press RESET and return to the menu. 4. After start training (FIGURE 27~29), TIME will be counted down. When TIME is counted
USER SELECT U1-U4
PRESSRESET 3 SEC TO RESET
CLOCKWISE ORANTI-CLOCKWISE
USER mode
PRESSENTER
CLOCKWISE ORANTI-CLOCKWISE
CLOCKWISE ORANTI-CLOCKWISE
PRESSENTER
PRESSENTER
CLOCKWISE ORANTI-CLOCKWISE
CLOCKWISE ORANTI-CLOCKWISE
PRESSENTER
CLOCKWISE ORANTI-CLOCKWISE
PRESSENTER
PRESSENTER
FUNCTION SELECT
TIME
CLOCKWISE ORANTI-CLOCKWISE
PRESSENTER
Repeating these opeartion till completing the setting of 20 ranges
CLOCKWISE ORANTI-CLOCKWISE
Hold on pressing for 2 seconds
FIGURE 29 FIGURE 30 FIGURE 31 FIGURE 32
FIGURE 33 FIGURE 34 FIGURE 35 FIGURE 36
USER SELECT U1-U4
PRESSRESET 3 SEC TO RESET
CLOCKWISE ORANTI-CLOCKWISE
H.R.C. mode
PRESSENTER
CLOCKWISE ORANTI-CLOCKWISE
CLOCKWISE ORANTI-CLOCKWISE
PRESSENTER
PRESSENTER
CLOCKWISE ORANTI-CLOCKWISE
CLOCKWISE ORANTI-CLOCKWISE
PRESSENTER CLOCKWISE OR
ANTI-CLOCKWISEPRESSENTER
PRESSENTER
FUNCTION SELECT
TIME
CLOCKWISE ORANTI-CLOCKWISE
PRESSENTER
TRAINING MODE SELECT
. RC
GAT
%05
%57
%09
CLOCKWISE ORANTI-CLOCKWISE
HEART RATE CONTROL
1. After enter HEART RATE CONTROL mode, the screen will show heart rate percentage 55%, 75%, 90% and TARGET. User may select heart rate percentage by turning UP/ DOWN joggle wheel for training.
2. User can preset the TIME data then press START/ STOP to start exercise. 3. After start training, TIME will be counted down. When the TIME is counted to 0, the
screen is flashing and the alarm is ringing. User can press any button to stop the alarm. If there is no HR input for 5 seconds, LCD will display until HR signal input.
FIGURE 37 FIGURE 38
RECOVERY After exercising for a period of time, keep holding on handgrips and press “RECOVERY” button. All function display will stop except “TIME” starts counting down from 00:60 to 00:00. Screen will display your heart rate recovery status with the F1, F2….to F6. F1 is the best, F6 is the worst. User may keep exercising to improve the heart rate recovery status. (Press the RECOVERY button again to return the main display.)
WATT CONSTANT 1. In standby mode, select WATT and press ENTER to enter. 2. The preset watt value 120 is flashing on screen, use UP/ DOWN joggle wheel to set target
value from 10 to 350. Pressing START button to start training. 3. User can preset the TIME data then press START/STOP to start exercise. 4. After start training, TIME will be counted down. When the TIME is counted to 0, the
screen is flashing and the alarm is ringing. User can press any button to stop the alarm. 5. Watt value is adjustable during training. User can turn the joggle wheel to adjust the Watt
according to the instruction: : Watt value > Setting value 25% --- User should show down
: Watt value in the Setting value 25% ---User should keep the same speed : Watt value < Setting value 25% --- User should ride faster
USER SELECT U1-U4
PRESSRESET 3 SEC TO RESET
CLOCKWISE ORANTI-CLOCKWISE
WATT mode
PRESSENTER
CLOCKWISE ORANTI-CLOCKWISE
CLOCKWISE ORANTI-CLOCKWISE
PRESSENTER
PRESSENTER
CLOCKWISE ORANTI-CLOCKWISE
CLOCKWISE ORANTI-CLOCKWISE
PRESSENTER CLOCKWISE OR
ANTI-CLOCKWISE
PRESSENTER PRESS
ENTER
FUNCTION SELECT
TIME
CLOCKWISE ORANTI-CLOCKWISE
PRESSENTER
WATT INSTALLED 120
3 5 0 +
10-
CLOCKWISE ORANTI-CLOCKWISE
FIGURE 39 FIGURE 40
NOTE:
1. When user stop pedaling for 4 minutes, computer will enter into power save mode, all setting and exercise data will stored until user start exercise again.
2. This computer requires 9V, 1A adaptor. 3. When computer act abnormal, please plug out the adaptor and plug in again.