B19 Canada:B05 - philips.encompass.com An isolation transformer should always be used during ... especially in the high voltage ... Chip diodes have a two letter identification code

MTNC050426A1 B19 Canada:B05

Color Television

CT-27HL15N CT-27HL15UN GN1M Please file and use this manual together with Simplified manual for model CT-32HL15N , Order No. MTNC050309A1 and the main

service manual for Model CT-32HL44J, Order No. MTNC040418C1. A complete parts list and schematics difference from Order No.

MTNC050309A1 are included in this simplified service manual.

© 2005 Panasonic Corporation of North America. All rights reserved. Unauthorized copying and distribution is a violation of law.

Page 1 of 32

7/7/2008http://tsn.pstc.panasonic.com/viewing/NA/CT-27HL15N/SIMP/MTNC050426A1/doc/MTN...

1 Safety precautions

General guidelines

An isolation transformer should always be used during the servicing of a receiver whose chassis is not isolated from AC power line.

Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical

shocks. It will also protect the receiver from being damaged by accidental shorting that may occur during servicing.

When servicing, observe the original lead dress, especially in the high voltage circuit. Replace all damaged parts (also parts that show

signs of overheating.)

Always replace protective devices, such as fish paper, isolation resistors and capacitors, and shields after servicing the receiver. Use

only manufacturer’s recommended rating for fuses, circuits breakers, etc.

High potentials are present when this receiver is operating. Operation of the receiver without the rear cover introduces danger for

electrical shock. Servicing should not be performed by anyone who is not thoroughly familiar with the necessary precautions when

servicing high voltage equipment.

Extreme care should be practiced when handling the picture tube. Rough handling may cause it to implode due to atmospheric

pressure. (14.7 lbs per sq. in.). Do not nick or scratch the glass or subject it to any undue pressure. When handling, use safety goggles

and heavy gloves for protection. Discharge the picture tube by shorting the anode to chassis ground (not to the cabinet or to other

mounting hardware). When discharging connect cold ground (i.e. dag ground lead) to the anode with a well insulated wire or use a

grounding probe.Avoid prolonged exposure at close range to unshielded areas of the picture tube to prevent exposure to x ray

radiation.

The test picture tube used for servicing the chassis at the bench should incorporate safety glass and magnetic shielding. The safety

glass provide shielding for the tube viewing area against x ray radiation as well as implosion. The magnetic shield limits the x ray

radiation around the bell of the picture tube in addition to the restricting magnetic effects. When using a picture tube test jig for service,

ensure that the jig is capable of handling 50kV without causing x ray radiation.

Before returning a serviced receiver to the owner, the service technician must thoroughly test the unit to ensure that is completely safe

to operate. Do not use a line isolation transformer when testing.

Leakage current cold check

Unplug the A.C. cord and connect a jumper between the two plug prongs.Measure the resistance between the jumpered AC plug and

expose metallic parts such as screwheads, antenna terminals, control shafts, etc. If the exposed metallic part has a return path to the

chassis, the reading should be between 240kΩ and 5.2MΩ. If the exposed metallic part does not have a return path to the chassis, the

reading should be infinite.

Leakage current hot check

Plug the AC cord directly into the AC outlet. Do not use an isolation transformer during the check.

Connect a 1.5kΩ 10 watt resistor in parallel with a 0.15µF capacitor between an exposed metallic part and ground. Use earth ground,

for example a water pipe.

Using a DVM with a 1000 ohms/volt sensitivity or higher, measure the AC potential across the resistor.

Repeat the procedure and measure the voltage present with all other exposed metallic parts.

Verify that any potential does not exceed 0.75 volt RMS. A leakage current tester (such a Simpson model 229, Sencore model PR57

or equivalent) may be used in the above procedure, in which case any current measure must not exceed 0.5 milliamp. If any

measurement is out of the specified limits, there is a possibility of a shock hazard and the receiver must be repaired and rechecked

before it is returned to the customer.

Hot check circuit

Insulation test

Connect an insulation tester between an exposed metallic part and A.C. line. Apply 2500VAC/60Hz for 1 second. Confirm that the

current measurement is lower than 4.0mA. Repeat test with other metallic exposed parts.

X ray radiation

Page 2 of 32


WARNING

The potential source of x ray radiation in the TV set is in the high voltage section and the picture tube.

NOTE

It is important to use an accurate, calibrated high voltage meter.

Set the brightness, picture, sharpness and color controls to minimum.

Measure the high voltage. With a 480i or 1080i signal the high voltage should be 29.5kV ± 0.3kV. If the upper limit is out of tolerance,

immediate service and correction is required to insure safe operation and to prevent the possibility of premature component failure.

Horizontal oscillator disable circuit test

This test must be performed as a final check before the receiver is returned to the customer. See horizontal oscillator disable circuit

procedure check in this manual.‘

2 Service notes

NOTE

These components are affixed with glue. Be careful not to break or damage any foil under the component or at the pins of the ICs

when removing. Usually applying heat to the component for a short time while twisting with tweezers will break the component loose.

Leadless chip component (surface mount)

Chip components must be replaced with identical chips due to critical foil track spacing. There are no holes in the board to mount

standard transistors or diodes. Some chips capacitor or resistor board solder pads may have holes through the board, however the

hole diameter limits standard resistor replacement to 1/8 watt. Standard capacitor may also be limited for the same reason. It is

recommended that identical components be used.

Chip resistor have a three digit numerical resistance code, 1st and 2nd significant digits and a multiplier. Example: 162 = 1600 or

1.6kΩ resistor, 0 = 0Ω (jumper).

Chip capacitors generally do not have the value indicated on the capacitor. The color of the component indicates the general range of

the capacitance.

Chip transistors are identified by a two letter code. The first letter indicates the type and the second letter, the grade of transistor.

Chip diodes have a two letter identification code as per the code chart and are a dual diode pack with either common anode or

common cathode. Check the parts list for correct diode number.

Component removal

1. Use solder wick to remove solder from component end caps or terminal.

2. Without pulling up, carefully twist the component with tweezers to break the adhesive.

3. Do not reuse removed leadless or chip components since they are subject to stress fracture during removal.

Chip component installation

1. Put a small amount of solder on the board soldering pads.

2. Hold the chip component against the soldering pads with tweezers or with a miniature alligator clip and apply heat to the pad area

with a 30 watt iron until solder flows. Do not apply heat for more than 3 seconds.

How to replace flat ic (required tools)

1. Remove the solder from all of the pins of a Flat IC by using a desolder braid

Page 3 of 32


2. Put the iron wire under the pins of the Flat IC and pull it in the direction indicated while heating the pins using a soldering iron. A

small awl can be used instead of the iron wire.

3. Remove the solder from all the pads of the Flat IC by using a de solder braid

4. Position the new Flat IC in place (apply the pins of the Flat IC to the soldering pads where the pins need to be soldered). Properly

determine the positions of the soldering pads and pins by correctly aligning the polarity symbol

5. Solder all pins to the soldering pads using a fine tipped soldering iron

6. Check with a magnifier for solder bridge between the pins or for dry joint between pins and soldering pads. To remove a solder

bridge, use a de solder braid as shown in the figure below

IMPORTANT

To protect against possible damage to the solid state devices due to arching or static discharge, make certain that all ground wires and

CRT DAG wire are securely connected.

CAUTION

The power supply circuit is above earth ground and the chassis cannot be polarized. Use an isolation transformer when servicing the

receiver to avoid damage to the test equipment or to the chassis. Connect the test equipment to the proper ground (hot) or (cold) when

servicing, or incorrect voltages will be measured.

WARNING

This receiver has been designed to meet or exceed applicable safety and x-ray radiation protection as specified by government

agencies and independent testing laboratories.

To maintain original product safety design standards relative to x-ray radiation and shock and fire hazard, parts indicated with the

symbol on the schematic must be replaced with identical parts. Order parts from the manufacturer’s parts center using the parts

numbers shown in this service manual, or provide the chassis number and the part reference number.

For optimum performance and reliability, all other parts should be replaced with components of identical specification.

Page 4 of 32


HORIZONTAL OSCILLATOR DISABLE CIRCUIT

This chassis employs a special circuit to protect against excessive high voltage and beam current. If, for any reason, the high voltage

and beam current exceed a predetermined level this protective circuit activates and detunes the horizontal oscillator that limits the high

voltage. The over-voltage protection circuit is not adjustable. However, if components indicated by the symbol on the schematic in

either the horizontal sweep system or the over-voltage protection circuit itself are changed, the operation of the circuit should be

checked using the following procedure:

Equipment needed to check the disabled circuit:

1. High voltage meter (0 ~ 50kV)

2. Variac or isolation transformer

3. D.C. current meter

4. Digital voltmeter

PREPARATION

1. Connect receiver to A.C. 120 Volts. Do not turn ON.

2. Connect HIGH VOLTAGE meter to 2nd anode (H.V. button).

NOTE

Use cold ground for negative lead.

3. Connect the ammeter serial from the flyback anode lead to the picture tube anode socket.

PROCEDURE

1. Apply a monoscope or white pattern.

2. Confirm that beam current is 2.0mA.

3. Adjust VR524 so that high voltage is 29.5kV ± 0.3kV.

4. Adjust VR538 so that digital meter reads 2.3 ± 0.05V

5. Confirm that high voltage protector (SOS) operates at 34.0kV or less by adjusting VR524.

6. Turn VR524 counter clockwise, turn tv on and apply a monoscope or white pattern.

7. Adjust VR524 so that high voltage meter reads 29.5 ± 0.3kV.

8. Once the adjustment is completed, apply a bond on VR524 and VR538. Confirm B+ 142V ± 6.0V with 120V A.C. applied.

NOTE

If high voltage is not within the specified limit the cause must be determined before the receiver is returned to the owner.

3 Receiver feature table

FEATURE/MODEL CT-27HL15N/UN

CHASSIS DP435

MICRO 256K

MENU LANGUAGE ENG/SPAN/FR

CLOSE CAPTION X

V-CHIP (USA/CANADA) X

VIDEO INPUT SKIP X

CHANNEL COUNT 181

REMOTE CONTROL (W/LIGHT) EUR7613ZC0

CRT SUPPLIER SAMSUNG

FAMILY GN1M

COMB FILTER 3D-Y/C

HEC/VEC (X=BOTH) X

VM X (SELECTABLE)

V/A NORM (X=BOTH) X

COLOR TEMP X

AI PICTURE X

PRESET/INPUT LABELING X

VIDEO PICTURE MEMORY X

HDTV MONITOR 1080i

PROGRESSIVE SCAN DOUBLER X

EDTV MONITOR 480p

STEREO/SAP WITH dbx NR X

Page 5 of 32


Note:

Specifications are subject to change without notice or obligation. Dimensions and weights are approximate.

4 Board description table

NOTE

When ordering a replacement board assembly, append an “S” to the board number.

EXAMPLE

To order the A Board, the replacement board is TNP2AH071ACS.

NOTE:

The DG-Board is non-serviceable. If this board is defective, replace it with a new board.

5 TV Location of controls

5.1 CT-27HL15N/UN

STEREO WATTS PER CHANNEL 10W

No. OF SPEAKERS 2

BASS/BALANCE/TREBLE CONTROL X

AI SOUND X

SURROUND X

SPATIALIZER/BBE BBE

A/V IN (REAR/FRONT) 4(3/1)

PROGRAM OUT X

AUDIO OUT (FAO / VAO) BOTH

COMPONENT INPUT (Y, Pb, Pr) 2

S-VIDEO INPUT (REAR/FRONT) 2/1

DIGITAL INTERFACE HDMI

WEIGHT (KG/LB) 43.0 KG/ 94.8LBS

DIMENSIONS (W/D/H) mm / in 780x508x572

BOARD CT-27HL15N/UN DESCRIPTION

A-BOARD TNP2AH071AC MAIN CHASSIS

D-BOARD TNP2AH073AF HIGH VOLTAGE AND DEFLECTION

DG-BOARD TNP2AA216 DIGITAL VIDEO

G-BOARD TNP2AA222 FRONT A/V

H-BOARD TNP2AA174AB REAR A/V

L-BOARD TNP2AA232AC CRT BOARD

Page 6 of 32


6 Back cover removal

CT-27HL15N/UN

7 Chassis service adjustment

Page 7 of 32


procedures

All service adjustments are factory preset and should not require change unless controls and/or associated components are replaced.

140.0_V B+ voltage check

1. Set the BRIGHT and PICTURE to minimum by using the PICTURE menu.

2. Connect the DVM on TPD50 (D-Board by and cold ground

3. Confirm that B+ voltage is 142V ± 6.0V. This voltage supplies B+ to the horizontal output and flyback circuits.

Source voltage chart

120V AC line input. Set the BRIGHT and the PICTURE to minimum by using the PICTURE menu. Use cold or hot ground for the (-) lead

of the DVM as needed

High voltage check

A-BOARD VOLTAGE

STBY 7V (BY IC006) A-Board TPA9 7.5V ± 0.75V

MAIN 9V (BY IC006) A-Board TPA90 9.0V ± 0.5V

MAIN 5V (BY IC2856) A-Board TPA15 5.2V ± 0.3V

GC 2.5V (BY IC2856) A-Board TPA25 2.6V ± 0.2V

STBY 3.3V (BY A13 CONNECTOR) A-Board TPA16 3.3V ± 0.2V

MAIN 3.3V (BY IC 2856) A-Board TPA33 3.3V ± 0.2V

D-BOARD VOLTAGE

+B2 (BY D14 CONNECTOR) D-Board TPD50 142.0 ± 6.0V

30V (BY IC805) D-Board TPD19 33.5 ± 2.0V

15V (BY IC802) D-Board TPD7 14.5 + 1.5V -1.0

-15V (BY IC805) D-Board TPD6 -15.5V ± 1.5V

SOUND+ (BY D6 CONNECTOR) D-Board TPD4 17.2V + 1.5V -1.0

SOUND- (BY D6 CONNECTOR) D-Board TPD53 -18.0V ± 1.5V

210V (BY IC503) D-Board TPD34 211.0V ± 4.0V

MAIN 12V (BY D14 CONNECTOR) D-Board TPD22 12V ± 0.5V

Page 8 of 32


1. Select an active TV channel and confirm that horizontal is in sync.

2. Adjust BRIGHTNESS and PICTURE using PICTURE icon menu so video just disappears.

3. Confirm B+ 142 ± 6.0V is within limit.

4. Using a high voltage meter confirm that the high voltage is 29.5kV ± 0.3kV.

7.1 Service adjustment default values for service items

NOTE:

The above table shows the default values for the service items, this values may vary depending on the serviced TV.

Important Note:

When changing “ID” register, message “Unplug AC to activate” will appear on the screen and the set must be unplugged.

REGISTER DESCRIPTION FORMAT

4:3 16:9

MTSIN INPUT LEVEL 22 N/A

SEPAL LOW LEVEL SEPARATION 07 N/A

SEPAH HIGH LEVEL SEPARATION 22 N/A

CLOCK CLOCK 131 N/A

COLOR COLOR 1F N/A

TINT TINT 7D N/A

BRIGH SUB-BRIGHTNESS 09 53 N/A

CONT SUB-CONTRAST 02 A0 N/A

B-Y_G MAGENTA TINT ADJ 3D N/A

CUT G GREEN CUT-OFF 01 15 N/A

CUT R RED CUT-OFF 01 1A N/A

CUT B BLUE CUT-OFF 01 17 N/A

BRT BRIGHT 09 53 N/A

R DR RED DRIVE 90 N/A

B DR BLUE DRIVE 95 N/A

R-Y_A R-Y_A 80 N/A

HLIN HORIZONTAL LINEARITY 80 N/A

HPOS HORIZONTAL POSITIONING 03 42 N/A

HWID HORIZONTAL WIDTH 95 N/A

PCC PINCUSHION CORRECTION D3 BD

PCCHG PINCUSHION HIGH 38 43

PCCLG PINCUSHION LOW 39 3F

PCCHS PINCUSHION HIGH 05 05

PCCLS PINCUSHION LOW 05 05

TOPG TOP CORNER PINCUSHION 58 58

BTMG BOTTOM CORNER PINCUSHION 58 58

TOPSL TOP CORNER PINCUSHION SLICE LEVEL 03 03

BTMSL BOTTOM CORNER PINCUSHION SLICE LEVEL 03 03

TRAP TRAPEZOID 80 80

PARA PARALLELOGRAM 10 10

SIDE E-W PINCUSHION ADJUSTMENT 16 16

HTRAP HORIZONTAL TRAPEZOID 20 20

VRAS VERTICAL POSITION CA D6

VEAMP VERTICAL SIZE 01 0F 00 56

V-C VERTICAL LINEARITY 70 72

V-S VERTICAL S CORRECTION 56 58

HDAFS HORIZONTAL DAF PHASE 00 A4 N/A

VTOP VTOP 00 C4 00 B0

BDAC BDAC 73 N/A

INPIN INPIN 20 20

MOIRE MOIRE 80 80

ID ID 32 32

Page 9 of 32


8 Identification of components

8.1 TV with back cover removed

TV View with back cover removed.

8.2 G Board

G-Board View

9 Reference of PDF links color

10 Conductors View

Page 10 of 32


10.1 G-Board Printed Circuit

11 Schematic Diagrams

11.1 Schematic notes in english

Page 11 of 32


11.2 Schematic notes in spanish

11.3 A-Board Schematic 1 of 3


Page 12 of 32



11.6 D-Board Schematic 1 of 4




11.10 G-Board Schematic

11.11 L-Board Schematic

12 Location Parts

CT-27HL15N/UN

Page 13 of 32


13 Parts list

13.1 Description of abbreviations guide

13.2 Parts list

Page 14 of 32


Ref. No. Part No. Part Name & Description Remarks

CAPACITORS

C037 ECA0JM222B CAP E 2200UF-6.3V

C038 ECJ2VF1H103Z CAP C .01UF-Z-50V

C047 ECA1HM330B CAP E 33UF-50V

C054 ECA1HM4R7B CAP E 4.7UF-50V


C056 ECA1VM471B CAP E 470UF-35V

C059 ECJ2VC1H101J CAP C 100PF-J-50V


C061 ECA1HMR22B CAP E .22UF-50V




C451 ECA1EM102E CAP E 1000UF-25V



C454 ECQV1H224JL3 CAP P .22UF-J-50V

C455 ECA1CM221B CAP E 10UF-16V

C457 ECQB1H471JF3 CAP P 470PF-J-50V

C458 ECQV1H105JL3 CAP P 1.0UF-J-50V

C460 ECQE2224KF3 CAP P .22UF-K-200V






C507 ECEA2CNR47SB CAP E .47UF-160V

C508 ECQB1H104JF3 CAP P .10UF-J-50V

C509 ECKR3A222KBP CAP C .0022UF-K-1KV

C510 ECWH20332JVY CAP P 3300PF-J-2KV

C511 ECWH20472JVB CAP P 4700PF-J-2KV

C512 ECA1HMR47B CAP E .47UF-50V

C514 ECQM4472JZW CAP P 4700PF-J-400V



C517 ECJ2VG1H151J CAP C 150-J-50V

C518 ECKW3D681KBR CAP C 680PF-K-2KV

C519 ECKW3D681KBP CAP C 680PF-K-2KV

C520 ECKW3D222KBP CAP C 2200UF-K-2KV

C521 ECWF2334JSR CAP M .33UF-J-200V

C522 ECWF4393RJB CAP P .039UF-J-400V



C525 EEUNA1E220B CAP E 22UF-25V







C536 ECEA1EN100UB CAP E 10UF-25V




C561 ECA2EHG470E CAP E 47UF-250V

C562 ECKR3A561KBP CAP C 560PF-K-1KV

C563 EEUEB2E330E CAP E 33UF-100V


Page 15 of 32



C567 EEUED2C101E CAP E 100UF-100V

C571 ECKRHT332KB CAP C 3300PF-K-




C577 ECQE6473RKF CAP P .047UF-K-600V

C578 ECKW3D681KBR CAP C 680PF-K-2KV



C589 ECQE6184JFB CAP P .18UF-J-600V

C590 ECJ2VB1H471K CAP C 470PF-K-50V



C801 ECQU2A224MLA CAP P .22UF-M-250V





C807 ECKCNA222MEB CAP C 2200PF-M-125V

C808 ECKCNA222MEB CAP C 2200PF-M-125V


C810 EETHC2D102J CAP E 1000UF-200V




C815 EEUFC1E222E CAP E 2200UF-25V





C825 ECA1HHG470B CAP E 47UF-50V


C827 ECA1HHG010B CAP E 1UF-50V

C828 ECKR3A331KBP CAP C 330PF-K-1KVDC

C830 EC0S2DA471BB CAP E 470UF-200V


C834 EEUFC1H222E CAP E 2200UF-50V




C841 ECA1VHG222E CAP E 2200UF-35V

C842 ECKR3A331KBP CAP C 330PF-K-1KVDC



C846 ECEA1CN101UB CAP E 100UF-16V


C855 EEUFC1A471B CAP E 470UF-10V

C857 ECA1HM471E CAP E 470UF-50V



C867 ECQM4103RJZ CAP P .01UF-J-400V







Page 16 of 32










C1052 ECEA1CKA470B CAP E 47UF-16V


C1402 ECJ2VF1C104Z CAP C .1UF-Z-16V
















C2202 ECEA1HKA2R2B CAP E 2.2UF-50V

C2203 ECEA1HKA4R7B CAP E 4.7UF-50V

C2204 TAP106K016CF CAP T 10MF-16V

C2205 ECEA1HKA010B CAP E 1.0UF-50V


C2207 TAP335K016CF CAP T 3.3 MF-16V

C2208 ECJ2VB1C104K CAP C .1UF-K-16V



C2211 ECEA1HKA100B CAP E 1UF-50V


C2215 ECEA1CKA101B CAP E 100UF-16V

C2218 ECEA1HKAR47B CAP E .47UF-50V



C2303 ECJ2VB1H332K CAP C .0033UF-K-50V















C2328 ECA1EM101B CAP E 100UF-25V



Page 17 of 32






















C2375 ECJ2VF1C105Z CAP C 1.0UF-Z-16V












C2455 ECJ2FB1C684K CAP C .68UF-Z-16C











C2466 ECJ2FB1C684K CAP C .68UF-Z-16C









C2857 EEUFC1C471B CAP E 470UF-16V



C2862 ECA1HM471E CAP E 470UF-50V




Page 18 of 32

















C3340 ECJ2YB1A105K CAP C 1.0UF-K-125V

































C3801 ECQE2104KFW CAP P .10UF-K-200V







C3811 ECKC3D332KBN CAP C 3300PF-K-2KV

C456A ECJ2VB1H472K CAP C .0047UF-K-50V

C468A ECJ2VB1H331K CAP C 330PF-K-50V

C469A ECJ2FB1H104K CAP C .1UF-K-50V

Page 19 of 32


C502A ECJ2VF1H104Z CAP C .1UF-Z-50V

C503A ECJ2VB1H102K CAP C .001UF-K-50V

CF803 D4DDF1R50001 DIODE

DIODES

D005 MA3X152K0L DIODE

D009 MA2C165001VT DIODE

D012 MAZ40360MF DIODE ZENER












D503 B0HALP000007 DIODE FAST RECOVERY

D506 B0JAME000058 DIODE SCHOTTKY BARR


D508 B0HAGV000004 DIODE FAST RECOVERY



D511 B0EALV000001 DIODE RECTIFIER




D522 B0AAGR000002 DIODE SWITCHING

D523 B0HASV000002 DIODE




D533 MA2C700A0F DIODE






D701 MA2C029TAF DIODE

D702 MA2C029TAF DIODE

D801 B0FBAT000006 DIODE RECTIFIER

D804 B0EBKM000023 DIODE RECTIFIER


D809 ERZV10D391 VARISTOR SURGE ABSORBER

D811 B0EAKL000008 DIODE RECTIFIER




D817 MAZ42200LF DIODE ZENER


D820 B0HAGM000005 DIODE FAST RECOVERY

D822 B0HAMM000036 DIODE FAST RECOVERY

D823 MAZ406800F DIODE ZENER

D824 B0BA01000070 DIODE VOLTAGE REGULATOR

D825 B0HANR000003 DIODE FAST RECOVERY

D827 B0HANM000038 DIODE FAST RECOVERY

D828 MA3D690 DIODE

D829 B0HAMM000124 DIODE

Page 20 of 32


D830 MA3D690 DIODE


D832 MAZ41100HF DIODE ZENER





D837 B0HAGV000004 DIODE FAST RECOVERY






D861 B0HAKM000005 DIODE FAST RECOVERY



D866 B0EAKT000018 DIODE RECTIFIER


D874 D4EAB3610002 DIODE ZENER

D875 MA3D690 DIODE

D876 B0JCME000037 DIODE SCHOTTKY BARR

D1001 LN81RPH DIODE



D1401 MA3X152E0L DIODE


D1550 MA2C700A0F DIODE

D1555 B0EAKL000008 DIODE RECTIFIER











D2312 MAZ41000LF DIODE ZENER




D2852 B0JCME000037 DIODE SCHOTTKY BARRIER



D2861 B0JAME000058 DIODE SCHOTTKY BARRIER





D3301 MAZ31100ML DIODE ZENER









Page 21 of 32

















D3332 CVS20A120MTA DIODE

D3334 CVS20A120MTA DIODE




















D3811 D4EAB3610002 DIODE

D3813 B0HALP000007 DIODE

RM001 B3RAC0000013 REMOTE CTRL RECEPTOR

FUSES

F801 XBA2A00101F FUSE

INTEGRATED CIRCUITS

IC002 TVR2AJ218S IC (EEPROM)

IC006 C1AB00000441 IC (FOR VIDEO EQUIPMENT)

IC451 C1AA00000680 IC (FOR VIDEO EQUIPMENT)

IC501 AN1431T-TA INT CKT

IC502 AN5751N INT CKT

IC801 C5HABZZ00126 INT CKT

IC802 C0EAS0000024 IC (VOLTAGE DETECTING)

IC805 C0DAAZG00014 IC (FOR POWER SUPPLY)

IC811 CNC1S171R INT CKT

IC901 C5AA00000212 INT CKT

IC1101 MN102H75KND INT CKT

IC1401 C0BBBA000022 IC (COMPARATOR)


IC1502 C0ABBA000168 IC (OPERATIONAL AMPLIFIER)


IC2201 AN5829S-E1V INT CKT

IC2301 TDA8925J AUDIO AMP IC

Page 22 of 32


IC2303 AN6914S-E1V INT CKT

IC2305 C0ABBA000168 IC (OPERATIONAL AMPLIFIER)

IC2451 NJW1164MPTE1 INT. CKT.

IC2851 C0CACKG00003 IC (VOLTAGE REGULATOR)





IC3001 C1AB00001991 INT CKT

IC3002 C1AB00001875 INT CKT

IC3801 TDA6118JF-N2 INT CKT (VIDEO OUTPUT)



IC5007 BA15218FDXE2 INT CKT

COILS

L002 TALV35VB330J COIL

L009 G0A330GA0024 COIL LINE CHOKE


L452 EXCELDR35V FERRITE BEAD

L453 ELC18B152L COIL CHOKE

L454 EXCELSA35T FERRITE BEAD





L509 ELC09D100F COIL CHOKE 10UH




L522 ELC18E121L COIL CHOKE 120UH


L554 ELH5L8115 COIL LINEARITY

L812 EXCELSA39E FERRITE BEAD

L813 EXCELSA39E FERRITE BEAD

L816 EXCELSA39V FERRITE BEAD




L821 EXCELSA39V FERRITE BEAD

L823 TLUADTB820K COIL


L825 ELC09D470DF COIL CHOKE 47UH





L845 G0A101ZA0041 COIL LINE CHOKE






L2855 G0A220GA0002 COIL LINE CHOKE





L3023 G0BYYYY00016 TRANSFORMER


Page 23 of 32




L3804 G0C1R0JA0021 DIODE



L3809 G0B250D00001 TRANSFORMER

L3810 G0B250D00001 TRANSFORMER

L552A ELH5L7740 COIL LINEARITY

LF801 G0B650H00002 COIL

LF802 HF2836622Y3R LINE FILTER

LF803 HF2836622Y3R LINE FILTER

LF904 G0B800H00001 COIL

LF2501 G0B800H00001 COIL

LF2502 G0B800H00001 COIL

LF3401 TF0402B04P03 LINE FILTER

TRANSISTORS

Q002 B1ABCF000115 TRANSISTOR

Q003 B1ADCE000009 TRANSISTOR







Q501 B1CEML000002 TRANSISTOR








Q551 2SC5686000LK TRANSISTOR

Q556 B1DAFU000003 TRANSISTOR

Q560 B1DGDN000001 TRANSISTOR

Q802 2SC3311A0A TRANSISTOR

Q803 2SC3311A0A TRANSISTOR



Q820 2SD21770RA TRANSISTOR

Q821 2SB14340RA TRANSISTOR

Q822 2SA1309A0A TRANSISTOR





Q827 2SB1011001TV TRANSISTOR













Page 24 of 32


















RELAYS

RL801 K6B1AGA00043 RELAY




RESISTORS

R032 ERJ6GEYJ333V RES M 33K-J-1/10W




R041 ERJ6GEYJ332V RES M 3.3K-J-1/10W

R075 ERJ6GEYJ101V RES M 100-J-1/10W


















R119 ERDS2TJ680T RES C 68-J-1/4W







R451 EROS2THF1001 RES M 1K-F-1/4W

R452 EROS2THF2201 RES M 2.2K-F-1/4W


R454 ERJ6ENF2202V RES M 22K-F-1/10W

R455 ERG2FJ331H RES M 330-J-2W


R457 ERDS1FJ560T RES C 56-J-1/2W

Page 25 of 32


R458 ERDS1FJ4R7P RES C 4.7-J-1/2W





R464 ERDS2TJ102T RES C 1K-J-1/4W








R472 ERJ6ENF1501V RES M 1.5K-F-1/10W









R505 ERG1SJ102P RES M 1K-J-1W

R507 ERX2FJR22H RES M .22-J-2W






R517 ERC14GK103V RES M 10K-J-1W












R534 ERDS2TJ152T RES C 1.5K-J-1/4W










R573 ERC14GK101V RES C 100-K-1/4W








Page 26 of 32















R597 ERF5AJ680 RES W 68-J-5W

R598 ERX12SJR22P RES M .22-J-1/2W

R599 ERX12SZJR15P RES M .15-J-1/2W

R718 ERG2FJ223H RESM 22K-J-2W



R734 EROS2THF1542 RES M 15.4KF-1/4W

R735 ERDS1FJ220P RES C 22-F-1/2W


R800 ERU5TCK1R5T RES F 1.5-K-5W

R801 ERC14GK824V RES C 820K-K-1/4W












R816 ERD75TAJ825 RES C 8.2MEG-J-3/4W













R841 ERQ12HKR22P RES F .22-K-1/2W

R842 ERQ12HKR22P RES F .22-K-1/2W









R852 ER050PHF2702 RES M 27-F-1/2W

Page 27 of 32





R857 ERX1SJ1R0P RES M 1.0-J-1W





























R893 ERDS1FJ332T RES C 3.3K-F-1/2W


R896 ERC14GK334V RES C 330K-K-1/4W




R902 ERJ6ENF56R0V RES M 56.0-F-1/10W


R905 ERQ1CJP331S RES F 330-J-1W



















Page 28 of 32



R1407 ERJ6ENF8200V RES M 820-F-1/10W




































R2305 ERG1SJ220P RES M 22-J-1W

R2306 ERG1SJ220P RES M 22-J-1W





















Page 29 of 32



























R2384 ERJ6ENF1100V RES M 110-F-1/10W






R2390 ERJ6ENF1100V RES M 110-F-1/10W























R2851 ERX2SJS1R3H RES M 1.3-J-2W

R2852 ERJ6ENF1202V RES.M 1.2K-F-1/10W




Page 30 of 32







































R3801 ERJ6ENF1000V RES M 100-F-1/10W

R3802 ERJ6ENF1000V RES M 100-F-1/10W

R3803 ERJ6ENF1000V RES M 100-F-1/10W




R3807 ERC12GK821D RES C 820-K-1/2W

R3808 ERC12GK821D RES C 820-K-1/2W

R3809 ERC12GK821D RES C 820-K-1/2W




SWITCHES

S801 N9ZZ00000284 SPARK GAP




SW001 TSE2AD002 SWITCH PUSH

SW002 EVQPBD05R SERVICE SWITCH




Page 31 of 32




TRANSFORMERS

T501 ETH19K207AZ TRANSFORMER

T550 G4E1A0000011 TRANSFORMER

T551 ZTFN95005A TRANSFORMER FLYBACK

T553 ETS28AU319AD CHOKE COIL

T801 ETS42AU185AD TRANSFORMER

T802 ETP28KBZA1ZG TRANSFORMER

OTHERS

TU001 ENG36A10GLF TUNER

M001 0FMK014ZZ MAGNET PERMALLOY

1 A68QCP693X CRT

2 EAS15S14B 6 OHM SPEAKER

M002 TBMA163 PANASONIC BADGE

M003 TKP2AA1551 LED BRACKET

M004 TKP2AA1581 SAFETY COVER

3 TKP2AA1591 GUIDE IR

4 TLY2AA046 DEFLECTION YOKE

M005 TMM2A30702 WEDGE YOKE

M006 TP-13000PX11 CONVERGENCE YOKE

M007 TSN63115-4 MAGNET PURITY

5 TSP2AA031 COIL DEGAUSSING

M008 TSX2AA0411 LINE CORD

M009 TXF3A01EA4 ASSY GROUND CABLE

M010 TXFKP05NSER ASSY SPEAKER BRACKET

M011 TXFKP22JSER ASSY AV BRACKET

6 TXFKU02NSER ASSY CABINET BACK

7 TXFKY11NSER ASSY CABINET FRONT

8 TKP2AA1562S ASSY FRONT DOOR

M012 TXFBX01NSER ASSY BUTTON POWER

JK3301 TJB2AA0521 TERMINAL A/V

JK3401 TJB2AA0571 TERMINAL A/V

JK3302A TJB2AA0532 TERMINAL A/V

SC3802 TJS2AC00401 SOCKET CRT

DG1 TJSF17350 CONNECTOR

DG3 TJSF17435 CONNECTOR

DG4 K1KA65B00003 CONNECTOR

DG5 K1KA08A00179 CONNECTOR

JK5001 K1FA119E0001 CONNECTOR

ACCESSORIES

M013 TQB2AA0531 OWNERS MANUAL

M014 EUR7613ZC0 TRANSMITTER REMOTE

M015 UR76EC0303E BATTERY COVER REMOTE CTRL

Page 32 of 32


Documents

B19 Canada:B05 - philips.encompass.com An isolation transformer should always be used during ... especially in the high voltage ... Chip diodes have a two letter identification code