Ideal crop marks

Below, listed by category and designation, are Standards published by the American Water Works Association and in e ect on December1, 2013. See the December 2013 and subsequent issues of Journal - American Water Works Association for o cial notice of any changes in the status of existing standards. The designations two-digit extension indicates the year of approval by the AWWA board of directors. denotes a rst-edition standard.

AWWA Standards

December 2013

Designation AWWA Standard

SOURCEGroundwater and WellsA100-06 Water Wells

TREATMENTFiltrationB100-09 Granular Filter MaterialB101-12 Precoat Filter MediaB102-10 Manganese Greensand for FiltersB110-09 Membrane SystemsB130-13 Membrane Bioreactor Systems SofteningB200-12 Sodium ChlorideB201-13 Soda AshB202-13 Quicklime and Hydrated LimeDisinfection ChemicalsB300-10 HypochloritesB301-10 Liquid ChlorineB302-10 Ammonium SulfateB303-10 Sodium ChloriteB304-13 Liquid Oxygen for Ozone Generation

for Water, Wastewater, and Reclaimed Water Systems

B305-06 Anhydrous AmmoniaB306-07 Aqua Ammonia (Liquid Ammonium

Hydroxide)CoagulationB402-12 Ferrous SulfateB403-09 Aluminum SulfateLiquid, Ground,

or LumpB404-08 Liquid Sodium SilicateB405-06 Sodium AluminateB406-06 Ferric SulfateB407-12 Liquid Ferric Chloride

Designation AWWA Standard

B408-10 Liquid Polyaluminum ChlorideB451-10 Poly (Diallyldimethylammonium

Chloride)B452-06 EPI-DMA PolyaminesB453-13 PolyacrylamideScale and Corrosion ControlB501-13 Sodium Hydroxide (Caustic Soda)B502-11 Sodium Polyphosphate, Glassy

(Sodium Hexametaphosphate)B503-11 Sodium TripolyphosphateB504-12 Monosodium Phosphate, Anhydrous

and LiquidB505-12 Disodium Phosphate, AnhydrousB506-13 Zinc OrthophosphateB510-12 Carbon DioxideB511-10 Potassium HydroxideB512-08 Sulfur DioxideB550-10 Calcium ChlorideTaste and Odor ControlB600-10 Powdered Activated CarbonB601-11 Sodium Metabisulfi teB602-08 Copper SulfateB603-10 PermanganatesB604-12 Granular Activated CarbonB605-13 Reactivation of Granular

Activated CarbonFluoridesB701-11 Sodium FluorideB702-11 Sodium FluorosilicateB703-11 Fluorosilicic Acid

Designation AWWA Standard

PIPE AND ACCESSORIESDuctile-Iron Pipe and FittingsC104/

A21.4-13CementMortar Lining for Ductile-Iron

Pipe and FittingsC105/

A21.5-10Polyethylene Encasement for Ductile-

Iron Pipe SystemsC110/

A21.10-12Ductile-Iron and Gray-Iron Fittings

C111/ A21.11-12

Rubber-Gasket Joints for Ductile-Iron Pressure Pipe and Fittings

C115/ A21.15-11

Flanged Ductile-Iron Pipe With Ductile-Iron or Gray-Iron Threaded Flanges

C116/ A21.16-09

Protective Fusion-Bonded Epoxy Coatings for the Interior and Exterior Surfaces of Ductile-Iron and Gray-Iron Fittings

C150/ A21.50-08

Thickness Design of Ductile-Iron Pipe

C151/ A21.51-09

Ductile-Iron Pipe, Centrifugally Cast

C153/ A21.53-11

Ductile-Iron Compact Fittings

Steel PipeC200-12 Steel Water Pipe, 6In. (150mm)

and LargerC203-08 Coal-Tar Protective Coatings and

Linings for Steel Water PipelinesEnamel and TapeHot-Applied

C205-12 CementMortar Protective Lining and Coating for Steel Water Pipe4In. (100mm) and LargerShop Applied

C206-11 Field Welding of Steel Water PipeC207-13 Steel Pipe Flanges for Waterworks

Service, Sizes 4In. Through 144In. (100mm Through 3,600mm)

C208-12 Dimensions for Fabricated Steel Water Pipe Fittings

C209-13 Cold-Applied Tape Coatings for Steel Water Pipe, Special Sections, Connections, and Fittings

C210-07 Liquid-Epoxy Coating Systems for the Interior and Exterior of Steel Water Pipelines

C213-07 Fusion-Bonded Epoxy Coating for the Interior and Exterior of Steel Water Pipelines

C214-07 Tape Coating Systems for the Exterior of Steel Water Pipelines

C215-10 Extruded Polyolefin Coatings for the Exterior of Steel Water Pipelines

Designation AWWA Standard

C216-07 Heat-Shrinkable Cross-Linked Polyolefin Coatings for the Exterior of Special Sections, Connections, and Fittings for Steel Water Pipelines

C217-09 Petrolatum and Petroleum Wax Tape Coatings for the Exterior of Connections and Fittings for Steel Water Pipelines

C218-08 Liquid Coating Systems for the Exterior of Aboveground Steel Water Pipelines and Fittings

C219-11 Bolted, Sleeve-Type Couplings for Plain-End Pipe

C220-12 Stainless-Steel Pipe, In. (13mm) and Larger

C221-12 Fabricated Steel Mechanical Slip-Type Expansion Joints

C222-08 Polyurethane Coatings for the Interior and Exterior of Steel Water Pipe and Fittings

C223-13 Fabricated Steel and Stainless Steel Tapping Sleeves

C224-11 Nylon-11-Based Polyamide Coating System for the Interior and Exterior of Steel Water Pipe, Connections, Fittings, and Special Sections

C225-07 Fused Polyolefin Coating Systems for the Exterior of Steel Water Pipelines

C226-13 Stainless-Steel Fittings for Waterworks Service, Sizes In. Through 72In. (13mm Through 1,800mm)

C227-11 Bolted, Split-Sleeve Restrained and Nonrestrained Couplings for Plain-End Pipe

C228-08 Stainless-Steel Pipe Flanges for Water ServiceSizes 2In. Through 72In. (50mm Through 1,800mm)

C229-08 Fusion-Bonded Polyethylene Coating for the Exterior of Steel Water Pipelines

C230-11 Stainless-Steel Full-Encirclement Repair and Service Connection Clamps

Concrete PipeC300-11 Reinforced Concrete Pressure Pipe,

Steel-Cylinder TypeC301-07 Prestressed Concrete Pressure Pipe,

Steel-Cylinder TypeC302-11 Reinforced Concrete Pressure Pipe,

Noncylinder TypeC303-08 Concrete Pressure Pipe, Bar-Wrapped,

Steel-Cylinder Type C304-07 Design of Prestressed Concrete

Cylinder Pipe

Designation AWWA Standard

Valves and HydrantsC500-09 Metal-Seated Gate Valves for Water

Supply Service C502-05 Dry-Barrel Fire HydrantsC503-05 Wet-Barrel Fire HydrantsC504-10 Rubber-Seated Butterfly Valves, 3In.

(75mm) Through 72In. (1,800mm)C507-11 Ball Valves, 6In. Through 60In.

(150mm Through 1,500mm)C508-09 Swing-Check Valves for Waterworks

Service, 2-In. Through 24-In. (50-mm Through 600-mm) NPS

C509-09 Resilient-Seated Gate Valves for Water Supply Service

C510-07 Double Check Valve Backflow Prevention Assembly

C511-07 Reduced-Pressure Principle Backflow Prevention Assembly

C512-07 Air-Release, Air/Vacuum, and Combination Air Valves for Waterworks Service

C515-09 Reduced-Wall, Resilient-Seated Gate Valves for Water Supply Service

C516-10 Large-Diameter Rubber-Seated Butterfly Valves, Sizes 78In. (2,000mm) and Larger

C517-09 Resilient-Seated Cast-Iron Eccentric Plug Valves

C518-13 Dual-Disc Swing-Check Valves for Waterworks Service

C520-10 Knife Gate Valves, Sizes 2In. (50mm) Through 96In. (2,400mm)

C530-12 Pilot-Operated Control ValvesC541-08 Hydraulic and Pneumatic Cylinder and

Vane-Type Actuators for Valves and Slide Gates

C542-09 Electric Motor Actuators for Valves and Slide Gates

C550-13 Protective Interior Coatings for Valves and Hydrants

C560-07 Cast-Iron Slide GatesC561-12 Fabricated Stainless-Steel Slide GatesC562-12 Fabricated Aluminum Slide GatesC563-12 Fabricated Composite Slide Gates

Designation AWWA Standard

PIPE INSTALLATIONC600-10 Installation of Ductile-Iron Mains and

Their AppurtenancesC602-11 CementMortar Lining of Water

Pipelines in Place4 In. (100 mm) and Larger

C604-11 Installation of Buried Steel Water Pipe4In. (100mm) and Larger

C605-05 Underground Installation of Polyvinyl Chloride (PVC) Pressure Pipe and Fittings for Water

C606-11 Grooved and Shouldered JointsC620-07 Spray-Applied In-Place Epoxy Lining

of Water Pipelines, 3In. (75mm) and Larger

DISINFECTION OF FACILITIESC651-05 Disinfecting Water MainsC652-11 Disinfection of Water-Storage FacilitiesC653-13 Disinfection of Water Treatment PlantsC654-13 Disinfection of WellsC655-09 Field DechlorinationC670-09 Online Chlorine Analyzer Operation

and Maintenance

METERSC700-09 Cold-Water MetersDisplacement

Type, Bronze Main CaseC701-12 Cold-Water MetersTurbine Type, for

Customer ServiceC702-10 Cold-Water MetersCompound TypeC703-11 Cold-Water MetersFire-Service TypeC704-12 Propeller-Type Meters for Waterworks

ApplicationsC706-10 Direct-Reading, Remote-Registration

Systems for Cold-Water MetersC707-10 Encoder-Type Remote-Registration

Systems for Cold-Water MetersC708-11 Cold-Water MetersMultijet TypeC710-09 Cold-Water MetersDisplacement

Type, Plastic Main CaseC712-10 Cold-Water MetersSinglejet TypeC713-10 Cold-Water MetersFluidic-Oscillator

TypeC714-13 ColdWater Meters for Residential Fire

Sprinkler Systems in One- and Two-Family Dwellings and Manufactured Homes

C750-10 Transit-Time Flowmeters in Full Closed Conduits

Designation AWWA Standard

SERVICE LINESC800-12 Underground Service Line Valves

and Fittings

PLASTIC PIPEC900-07 Polyvinyl Chloride (PVC) Pressure Pipe

and Fabricated Fittings, 4In. Through 12In. (100mm Through 300mm), for Water Transmission and Distribution

C901-08 Polyethylene (PE) Pressure Pipe and Tubing, In. (13mm) Through 3In. (76mm), for Water Service

C903-05 PolyethyleneAluminumPolyethylene & Cross-linked PolyethyleneAluminumCross-linked Polyethylene Composite Pressure Pipes, In. (12mm) Through 2In. (50mm), for Water Service

C904-06 Cross-Linked Polyethylene (PEX) Pressure Pipe, In. (12mm) Through 3In. (76mm), for Water Service

C905-10 Polyvinyl Chloride (PVC) Pressure Pipe and Fabricated Fittings, 14In. Through 48In. (350mm Through 1,200mm)

C906-07 Polyethylene (PE) Pressure Pipe and Fittings, 4In. (100mm) Through 63In. (1,600mm), for Water Distribution and Transmission

C907-12 Injection-Molded Polyvinyl Chloride (PVC) Pressure Fittings, 4In. Through 12In. (100mm Through 300mm), for Water, Wastewater, and Reclaimed Water Service

C909-09 Molecularly Oriented Polyvinyl Chloride (PVCO) Pressure Pipe, 4In. Through 24In. (100mm Through 600mm), for Water, Wastewater, and Reclaimed Water Service

C950-13 Fiberglass Pressure Pipe

STORAGED100-11 Welded Carbon Steel Tanks for

Water StorageD102-11 Coating Steel Water-Storage TanksD103-09 Factory-Coated Bolted Carbon Steel

Tanks for Water StorageD104-11 Automatically Controlled, Impressed-

Current Cathodic Protection for the Interior Submerged Surfaces of Steel Water Storage Tanks

Designation AWWA Standard

D106-10 Sacrificial Anode Cathodic Protection Systems for the Interior Submerged Surfaces of Steel Water Storage Tank

D107-10 Composite Elevated Tanks for Water Storage

D108-10 Aluminum Dome Roofs for Water Storage Facilities

D110-13 Wire- and Strand-Wound, Circular, Prestressed Concrete Water Tanks

D115-06 Tendon-Prestressed Concrete Water TanksD120-09 Thermosetting Fiberglass-Reinforced

Plastic TanksD121-12 Bolted Aboveground Thermosetting

Fiberglass-Reinforced Plastic Panel-Type Tanks for Water Storage

D130-11 Geomembrane Materials for Potable Water Applications

PUMPSE102-06 Submersible Vertical Turbine PumpsE103-07 Horizontal and Vertical Line-Shaft

Pumps

PLANT EQUIPMENTF101-13 Contact-Molded, Fiberglass-Reinforced

Plastic Wash-Water Troughs and Launders

F102-13 Matched-Die-Molded, Fiberglass-Reinforced Plastic Weir Plates, Scum Baffles, and Mounting Brackets

F110-12 Ultraviolet Disinfection Systems for Drinking Water

UTILITY MANAGEMENTG100-11 Water Treatment Plant Operation

and ManagementG200-09 Distribution Systems Operation

and ManagementG300-07 Source Water ProtectionG400-09 Utility Management SystemG410-09 Business Practices for Operation

and ManagementG420-09 Communications and Customer

RelationsG430-09 Security Practices for Operation

and ManagementG440-11 Emergency Preparedness PracticeG480-13

J100-10 (R13)

Water Conservation Program Operation and Management

Risk and Resilience Management of Water and Wastewater Systems