AWK-4630 Workstation...ACS-2907 User Manual 7 1.3 Brief Description of ACS-2907 ACS-2907 is a Fan-less wall mounting and ultra-compact standalone Box PC, powered by an Intel Atom D525

ACS-2907 User Manual 1

ACS-2907

Box PC User Manual

Revision

Date Version Remark

Jan. 2013 V1.0

® 2012 Aplex Technology, Inc. All Rights Reserved. Published in Taiwan

Aplex Technology, Inc.

15F-1, No.186, Jian Yi Road, Zhonghe District, New Taipei City 235, Taiwan

Tel: 886-2-82262881 Fax: 886-2-82262883 E-mail: [email protected] URL: www.aplex.com.tw

mailto:[email protected]

http://www.aplex.com.tw/


Warning!___________________________________

This equipment generates, uses and can radiate radio frequency energy and if not installed and

used in accordance with the instructions manual, it may cause interference to radio communications.

It has been tested and found to comply with the limits for a Class A computing device pursuant to

FCC Rules, which are designed to provide reasonable protection against such interference when

operated in a commercial environment. Operation of this equipment in a residential area is likely

to cause interference in which case the user at his own expense will be required to take whatever

measures may be required to correct the interference.

Disclaimer

This information in this document is subject to change without notice. In no event shall Aplex Technology

Inc. be liable for damages of any kind, whether incidental or consequential, arising from either the use or

misuse of information in this document or in any related materials.

Electric Shock Hazard – Do not operate the machine with its back cover removed. There are

dangerous high voltages inside.


Table of Contents______________________

Warning!…………………………………………………………………………….……..….2

Disclaimer………………………………………………………………….…………………2

Chapter 1 Getting Started

1.1 Specifications……………………………………….……………………..5

1.2 Dimensions………………………………...………………………….......6

1.3 Brief Description…………………………………………………….……7

Chapter 2 Hardware

2.1 Mainboard………………..…….……………………………………..…..8

2.2 Jumpers and Connectors Location……………………………………...11

2.3 Jumpers Setting and Connectors……………...………………………12

Chapter 3 BIOS Setup

3.1 Operations after POST Screen..........................................................21

3.2 BIOS SETUP UTILITY..........................................................................22

3.3 System Overview..................................................................................23

3.4 Advanced Settings............................................................................... 24

3.5 Advanced PCI/PnP Settings................................................................ 32

3.6 Boot Settings....................................................................................... 34

3.7 Security Settings.................................................................................. 36

3.8 Advanced Chipset Settings.................................................................. 38

3.9 Exit Options…………………………………...…………………………….43

Chapter 4 Installation of Drivers

4.1 Intel Chipset Driver.…………………………...…………………………46

4.2 Intel Graphics Media Accelerator Driver...…………………..…………..49

4.3 Intel 8257L Network Adapter………………………………………….….52

4.4 Realtek HD Audio Driver Installation…….…………..…………………55

4.5 Capture Driver……………………........................................................58

Figures

Figure 1.1:Dimensions of ACS-2907…………………………………..…....6

Figure 1.2: Rear view of ACS-2907…………………………………………7

Figure 1.3: Front view of ACS-2907………………………….……………….7

Figure 2.1: Mainboard Overview………………………………………….....8


Figure 2.2: Jumpers and Connectors Location Board Top………………..11

Figure 2.3: Jumpers and Connectors Location Board Bottom…………….11


Chapter 1 System

1.1 Specifications

Specs ACS-2907

CPU Intel (R) Atom D525

Chipset ICH8M

System Memory 2GB DDR3 800 MHz on board

External I/O Port 2 x USB

1 x RJ45 GbE LAN

1 x D-SUB VGA

4 x BNC connectors

1 x DC 12V terminal block connector

1 x 6 pins T/B connector for GPO

1 x Ground Screw

1 XCOM DB9 RS-232

1 X Power Switch (rocker switch)

1 X Audio Line out

Storage 1 x 2.5" SATA HDD Space

Power Supply DC 12V

OS Support Windows XP Pro, XP Embedded

Mounting Wall Mount Kit

Construction and Color Aluminum sink & Heavy-duty steel chassis

(Black)

Dimensions (WxHxD) 232.5 X 200 X 47 mm

269.5 X 200 X 53 mm(wall mount)

Operating Temperature 0~50℃

Storage Temperature -20~60℃

Relative Humidity 10%~90%@ 40 ﾟ C, (non-condensing)

Certificate CE/FCC Class A


1.2 Dimensions

Figure 1.1: Dimensions of ACS-2907


1.3 Brief Description of ACS-2907

ACS-2907 is a Fan-less wall mounting and ultra-compact standalone Box PC, powered by an Intel

Atom D525 1.8Ghz and supporting 2 x USB, 4 x BNC connectors, 1 x D-SUB VGA, 1 x SATA HDD

space, DC 12V power input etc. ACS-2907 works very well along with any of our Display Monitor

series and it absolutely can provide an easy way to perform control and field maintenance.

Figure 1.2: Rear view of ACS-2907

Figure 1.3:Front view of ACS-2907


Chapter 2 Hardware

2.1 Mainboard

Figure 2.1 Mainboard Overview


ASB-D525GT is a 3.5" industrial Embedded motherboard developed on the basis of Intel Atom D525

and ICH8M, onboard 2GB DDR3 SDRAM,which provides abundant peripheral interfaces to meet the

needs of different customers. Also, it features one 1000M LAN ports, four BNC (two TV in ports, two

TV out ports), one mSATA, one Mini PCIE configuration. Due to its compact size, the product is widely

used in various sectors of industrial decoding and encoding control.

Specifications

Board Size 152mm x 105mm

CPU Support onboard Intel Atom dual core D525 /1.8GHz (ASB-D525GT)

onboard Intel Atom N455 /1.66GHz (option） (ASB-N455GT)

Chipset Intel ICH8M

Memory

Support

Onboard 2GB DDR3 800 MHz FSB

Graphics Integrated by D525 / N455 GMA 3150

Super I/O Winbond W83627UHG

BIOS AMIBIOS

Storage 2 x SATA Connector

1 x mSATA Slot

Network 1 x RJ-45 1000Mbps LAN Intel 82574L

USB 2 x USB 2.0 stack port for external

2 x USB 2.0 Pin header for internal

Serial 1 x RS-232 header for internal , pin 10 w/5V (COM1)

1 x RS-485 for internal (COM2)

Digital I/O 3-bit digital I/O by Connector

1-bit digital Input

2-bit digital output

Battery Support CR2477 Li battery by 2-pin header

Audio Support Audio via Realtek ALC662 HD audio decoder

Support Line-in, Line-out, MIC by 2x6-pin header

Keyboard 1x PS2 keyboard by pin header for COM2

Power

Management

DC12V input

1 x 2-pin power input connector

Front I/O by 2x5-pin header

Power on/off switch

Reset switch


Power LED status

HDD LED status

WAN LED status

Watchdog

Timer

Software programmable 1 – 255 second by Super I/O

External I/O

port

2 x BNC Ports (TV_IN1,TV_IN2)

2 x BNC Ports (TV_OUT1,TV_OUT2)

1 x SIM Socket

2 x USB 2.0 Ports (stack)

1 x RJ45 GbE Port (10/100/1000Mbps)

1 x VGA Port

1 x GPI by Connector

2 x GPO by Connector

Temperature Operating: -10℃–60℃

Storage: -20℃–80℃

Humidity 5% - 95%, non-condensing, operating

Power

Consumption

12V /1.20A (Intel Atom D525 processor with 2GB DDR3

DRAM)

12V /0.90A (Intel Atom N455 processor with 2GB DDR3

DRAM)

EMI/EMS Meet CE/FCC class A

mailto:@1.45A

mailto:@1.45A


2.2 Jumpers and Connectors Location

Figure 2.2: Board Top

Figure 2.3: Board Bottom


2.3 Jumpers Setting and Connectors

1. JP5:

(2.0mm Pitch 1X2 Pin Header), ATX Power and auto Power on setting jumper.

JP5 Mode

Open ATX Power Mode

Close Auto Power on

(Default)

2. BAT1:

(1.25mm Pitch 1X2 box Pin Header) 3.0V Li battery is embedded to provide power for

CMOS.

Pin# Signal

Name

Pin1 VBAT

Pin2 Ground

3. DC_IN:

(3.5mm 1x2 Pin Connector),DC12V System power input connector.

【Power input “+”and “-” reverse connection protection, but can not boot】.

Pin# Signal Name

1 +12V

(+)

2 Ground

(-)

Note:

Make sure that the voltage of power supply is DC(12±5%)V before power on, or

it may cause boot up failure and even system damage.


4. PWR_SW:

ATX Power Mode POWER on/off Button.

(Note: JP5 setting open).

5. RST_SW:

RESET Switch Button.

6. FP1:

(2.0mm Pitch 2X5 Pin Header), Front panel connector.

Signal Name Pin# Pin# Signal Name

HDD LED+ 1 2 POWER

LED+

Ground 3 4 Ground

Ground 5 6 PWR_ON

RESET+ 7 8 Ground

WAN LED- 9 10 WAN LED+

Pin1-3: HDD LED, They are used to connect hard disk activity LED. The LED blinks

when the hard disk is reading or writing data.

Pin2-4: POWER LED, They are used to connect power LED. When the system is

powered on or under S0/S1 state, the LED is normally on; when the

system is under S4/S5 state, the LED is off.

Pin5-6: POWER on/off Button , They are used to connect power switch button.

The two pins are disconnected under normal condition. You may short

them temporarily to realize system startup & shutdown or awaken the

system from sleep state.

Pin7-8: RESET Button, They are used to connect reset button. The two pins are

dis-

connected under normal condition. You may short them temporarily to

realize

system reset.

Pin9-10: WAN LED, They are used to connect WAN activity LED.

Note:

When connecting LEDs and buttons, pay special attention to the signal

pola-

rity. Make sure that the connector pins have a one-to-one correspondence


with chassis wiring, or it may cause boot up failure.

7. TV_IN1:

(BNC Port), Analog Video Input, CVBS Signal. TV_OUT1 is TV_IN1 monitor Video output.

8. TV_IN2:

(BNC Port), Analog Video Input, CVBS Signal. TV_OUT2 is TV_IN2 monitor Video output.

9. TV_OUT1:

(BNC Port), Analog Video output, CVBS Signal. TV_IN1 is TV_OUT1 video input.

10. TV_OUT2:

(BNC Port), Analog Video output, CVBS Signal. TV_IN2 is TV_OUT2 video input.

Video Input monitor output

TV_IN1 TV_OUT1

TV_IN2 TV_OUT2

11. LAN1:

(RJ45 Connector), Rear LAN port, one standard 10/100/1000M RJ-45 Ethernet port are

provided. Used Intel 82574L chipset ,LINK LED (green) and ACTIVE LED (yellow)

respectively located at the left-hand and right-hand side of the Ethernet port indicate

the activity and transmission state of LAN.

12. GPIO:

(3.0mm Pitch 1x6 Pin Connector),General-purpose input/output port, it provides a


group of self-programming interfaces to customers for flexible use.

Pin# Signal Name

1 GPI, 5V Level Signal.

2 Ground

3 GPO1_A

GPO1 Relay control switch A Port, (Relay Default

Close)

4 GPO1_B

GPO1 Relay control switch B Port, (Relay Default

Close)

5 GPO2_A

GPO2 Relay control switch A Port, (Relay Default

Close)

6 GPO2_B

GPO2 Relay control switch B Port, (Relay Default

Close)

13. CPU_FAN1:

(2.54mm Pitch 1x3 Pin Header),Fan connector, cooling fans can be connected directly

for use. You may set the rotation condition of cooling fan in menu of BIOS CMOS

Setup.Fan speed control with CPU temperature, Boot OS after the start of temperature

control.

- CPU temperature less than 50℃: FAN not rotate.

- CPU temperature 50℃~60℃: FAN low speed rotate.

- CPU temperature 60℃~70℃: FAN high speed rotate.

- CPU temperature high than 70℃: FAN full speed rotate.

Pin# Signal Name

1 Ground

2 VCC

3 Rotation

detection


Note:

Output power of cooling fan must be limited under 5W.

14. LVDS1:

For 18 bit LVDS output connector, Fully supported by Intel D525(N455) chipset, the

interface features single channel 18-bit output. Model name of the interface connector

is Hirose DF13-20DP-1.25V.Support LVDS Backlight Control.


VCC_LVDS 2 1 VCC_LVDS

Ground 4 3 Ground

LA_DATAP0 6 5 LA_DATAN0



NC 12 11 NC

LA_CLKP 14 13 LA_CLKN

Ground 16 15 Ground

BKLT_EN_OUT 18 17 BKLT_CTRL

12V 20 19 12V

15. BZ:

Onboard buzzer.

16. COM1:

(2.0mm Pitch 2x5 Pin Header), COM1 Port, standard RS232 ports are provided. They

can be used directly via COM cable connection.


DCD# (Data Carrier

Detect)

1 2 RXD (Received Data)

TXD (Transmit Data) 3 4 DTR (Data Terminal

Ready)

Ground 5 6 DSR (Data Set Ready)

RTS (Request To Send) 7 8 CTS (Clear To Send)

RI 9 10 5V


17. COM2:

(2.0mm Pitch 1x6 box Pin Header),it provides selectable RS485 and PS2 keyboard by

signal output.

PS/2 keyboard Pin# RS485

PS2_KB_DATA 1 (NC)

(NC) 2 RS485+

Ground 3 Ground

5V 4 (NC)

PS2_KB_CLK 5 (NC)

(NC) 6 RS485-

18. CRT2:

(CRT Connector DB15),Video Graphic Array Port, provide high-quality video output.

19. USB23 (Default):

(Double stack USB type A), USB2 and USB3 connector, it provides up to two USB2.0

ports, speed up to 480Mb/s. they can not work at the same time for USB23 and

USB23A.

USB23A (option):

(2.0mm Pitch 2x5 Pin Header) , USB2 and USB3 connector, it provides two USB ports

via a dedicated USB cable, speed up to 480Mb/s.


VCC(+5V) 1 2 VCC(+5V)

USB3_N 3 4 USB2_N

USB3_P 5 6 USB2_P

Ground 7 8 Ground


NC 9 10 Ground

20. USB4/USB5:

(2.0mm Pitch 2x5 Pin Header),USB4 and USB5 connector, it provides two USB ports

via a dedicated USB cable, speed up to 480Mb/s.


VCC(+5V) 1 2 VCC(+5V)

USB5_N 3 4 USB4_N

USB5_P 5 6 USB4_P

Ground 7 8 Ground

NC 9 10 Ground

Note:

Before connection, make sure that pinout of the USB Cable is in accordance with that

of the said tables. Any inconformity may cause system down and even hardware

damages.

21. SIM1:

SIM Socket, SIM card and wireless network card used together.

SIM Socket：Insert SIM card.

MPCIE1 Socket：Insert wireless network card.

22. F_AUDIO:

(2.0mm Pitch 2X6 Pin Header), Front Audio, An onboard Realtek ALC662 codec is

used to provide high-quality audio I/O ports. Line Out can be connected to a

headphone or amplifier. Line In is used for the connection of external audio source via

a Line in cable. MIC is the port for microphone input audio.


VCC(+5V) 1 2 Ground

LINE_OUT_L 3 4 LINE_OUT_

R

FRONT_JD 5 6 LINE1_JD

LINE_IN_L 7 8 LINE_IN_R

MIC_IN_L 9 10 MIC_IN_R

Ground 11 12 MIC1_JD


23. SATA_P:

(2.5mm Pitch 1x2 box Pin Header),an onboard 5V output connector is reserved to

provide power for SATA devices.

Pin# Signal

Name

1 +DC5V

2 Ground

Note:

Output current of the connector must not be above 1A.

24. SATA1/SATA2:

(SATA 7P),SATA1,SATA2 SATA Connectors, Two SATA connectors are

provided, with transfer speed up to 3.0Gb/s.

25. LED1/LED2/LED3/LED4:

Onboard LED status.

LED1: Standby Power Good status.

LED2: Power on status.

LED3: HDD Read /write status.

LED4: Video Capture Card status.

26. MPCIE1:

(30mmx30mm /50.95x30mm Socket 52Pin ),mini PCIE socket, it is located at the top, it

supports mini PCI-E devices with USB2.0, SMBUS ,SIM,and PCI-E signal.

27. H3/H4/H5/H6:

D525(N455) and ICH8M Heat Sink SCREW HOLES, Four screw holes for intel D525

(N455) and ICH8M Heat Sink assemble.

28. H7/H8:

MPCIE1 SCREW HOLES,


H7 for mini PCIE card (50.95mmx30mm Socket 52 Pin) assemble.

H8 for mini PCIE card (30mmx30mm Socket 52 Pin) assemble.

29. H9/H10:

U53 and U54 Heat Sink SCREW HOLES, two screw holes for U53 and U54 Heat Sink

assemble.

30. M_SATA:

(50.95mmx30mm Socket 52Pin), mSATA socket, it is located at the bottom, it supports

mini PCI-E devices with USB2.0, B2 mSATA bus for flash disk signal.

31. H1/H2:

M_SATA SCREW HOLES,

H1 and H2 for mini M_SATA card (50.95mmx30mm Socket 52 Pin) assemble.


Chapter 3 BIOS Setup

3.1 Operations after POST Screen

After CMOS discharge or BIOS flashing operation, the system will display the

following screen for your further operation. Press F2 key to continue or F1 key to

enter CMOS Setup.

AMIBIOS© 2009 American Mega trends , Inc. BIOS Date: 08/03/11 11:01:23 Ver: 08.00.16

CPU : Intel(R) Atom(TM) CPU D525 @ 1.80GHz

Speed : 1.80 GHz Press F11 for BBS POPUP Initializing USB Controllers. . Done. 2039MB OK Press delete to Run SETUP

After optimizing and exiting CMOS Setup, the POST screen displayed for the first time is

as follows and includes basic information on BIOS, CPU, memory, and storage devices.

AMIBIOS© 2009 American Mega trends , Inc. BIOS Date: 08/03/11 11:01:23 Ver: 08.00.16

CPU : Intel(R) Atom(TM) CPU D525 @ 1.80GHz

Speed : 1.80 GHz Press F11 for BBS POPUP Initializing USB Controllers. . Done. 2039MB OK Press delete to Run SETUP

Press F11 to load default values and continue 0085

Press F11 key to enter Boot Menu during POST, as shown by the following figure.


Please select boot device：

USB: USB Hotplug FDD

Network: IBA GE Slot 0300 v1353

SATA:4M-CSS HAK40-004G

↑and ↓ to move selection

ENTER to select Boot device

ESC to boot using defaults

3.2 BIOS SETUP UTILITY

Press [Del] key to enter BIOS Setup utility during POST, and then a main menu

containing system summary information will appear.

BIOS SETUP UTILITY

Main Advanced PCIPnP Boot Security Chipset Exit

System Overview User [ENTER]，[TAB]

or [SHIFT-TAB] to

Select a field

Use[+] or [-] to

configure system Time.

← Select Screen

↑↓ Select Item

+- Charge Field

Tab Select Field

F1 General Help

F10 Save and Exit

ESC Exit

AMIBIOS

Version : 08.00.16

Build Date : 08/03/11

ID : D525G009

Processor

Intel(R) Atom(TM) CPU D525 @ 1.80GHz

Speed :1800MHz

Count : 2

System Memory

Size :2039MB

System Time [00:01:18]

System Date [Tue 08/03/2011]

V02.68 © Copyright 1985-2009 American Megatrends , Inc.


3.3 System Overview

BIOS SETUP UTILITY


System Overview User [ENTER]，[TAB]

or [SHIFT-TAB] to

Select a field

Use[+] or [-] to

configure system Time.

← Select Screen

↑↓ Select Item

+- Charge Field

Tab Select Field

F1 General Help

F10 Save and Exit

ESC Exit

AMIBIOS

Version : 08.00.16

Build Date : 08/03/11

ID : D525G009

Processor


Speed :1800MHz

Count : 2

System Memory

Size :2039MB

System Time [00:02:28]

System Date [Tue 08/03/2011]


System Time:

Set the system time, the time format is:

Hour : 0 to 23

Minute : 0 to 59

Second : 0 to 59

System Date:

Set the system date, the date format is:

Day: Note that the „Day‟ automatically changes when you set the date.

Month: 01 to 12

Date: 01 to 31

Year: 2009 to 2099


3.4 Advanced Settings

BIOS SETUP UTILITY


Advanced Settings Configure CPU

← Select Screen

↑↓ Select Item

Enter Charge Field

F1 General Help

F10 Save and Exit

ESC Exit

WARNING: Setting wrong values In below

sections

may cause system to malfunction.

► CPU Configuration

► IDE Configuration

► Super IO Configuration

► Hardware Health Configuration

► ACPI Configuration

► AHCI Configuration

► MPS Configuration

► PCI Express Configuration

► Smbios Configuration

► USB Configuration


3.4.1 CPU Configuration

BIOS SETUP UTILITY

Advanced

Configure advanced CPU settings

Module Version: 3F.1C

For UP platforms,

Leave it enabled.

For DP/MP serves,

It may use to tune

Performance to the

Specific application.

Manufacturer : Intel


Frequency :1.80GHz

FSB Speed : 800MHz

Cache L1 : 48 KB

Cache L2 :1024 KB

Max CPUID Value Limit [Disabled]


Execute-Disable Bit Capability [Enabled]

Hyper Threading Technology [Disabled]

← Select Screen

↑↓ Select Item

+- Charge Field

F1 General Help

F10 Save and Exit

ESC Exit


Max CPUID Value Limit:

[Enabled]

[Disabled]

Execute-Disable Bit Capability:

[Disabled]

[Enabled]

Hyper Threading Technology:

[Disabled]

[Enabled]

3.4.2 IDE Configuration

BIOS SETUP UTILITY

Advanced

IDE Configuration Disabled

Enhanced

← Select Screen

↑↓ Select Item

+- Charge Field

F1 General Help

F10 Save and Exit

ESC Exit

SATA#1 Configuration [Enhanced]

Configure SATA as [IDE]

► Primary IDE Master : [Not

Detected]

► Primary IDE Slaver : [Not

Detected]

► Secondary IDE Master : [Not

Detected]

► Secondary IDE Slaver : [Not

Detected]

► Third IDE Master : [Not

Detected]

► Third IDE Slaver : [Not

Detected]


► Fourth IDE Master : [Not

Detected]

► Fourth IDE Slaver : [Not

Detected]

Hard Disk Write Protect [Disabled]

IDE Detect Time Out (Sec) [35]

ATA(PI) 80Pin Cable Detection [Host &

Device]


SATA#1 Configuration:

[Disabled]

[Enhanced]

Configure SATA as:

[IDE]

[AHCI]

Hard Disk Write Protect:

[Disabled]

[Enabled]

IDE Detect Time Out :

[35]

[0]

[5]

[10]

[15]

[20]

[25]

[30]

ATA(PI) 80Pin Cable Detection:

[Host & Device]

[Host]

[Device]

3.4.3 Super IO Configuration


BIOS SETUP UTILITY

Advanced

Configure Win627UHG Super IO Chipset Allow BIOS to Enable

Or Disable Floppy

Controller.

← Select Screen

↑↓ Select Item

+- Charge Field

F1 General Help

F10 Save and Exit

ESC Exit

Onboard Floppy controller [Enabled]

Floppy Drive Swap [Disabled]

Serial Port1 Address [3F8/IRQ4]

Serial Port2 Address [2F8/IRO3]

Serial Port2 Mode [Normal]

Serial Port Address [378]

Serial Port Mode [Normal]]

Serial Port IRQ [IRQ7]

Keyboard PowerOn [Disabled]

Specific Key PowerOn

Mouse PowerOn [Disabled]


3.4.4 Hardware Health Configuration

BIOS SETUP UTILITY

Advanced

Hardware Health Configuration

Enables Hardware

Health Monitoring

Device.

H/W Health Function [Enabled]

Hardware Health Event Monitoring

---------------------------------------------------------------

-----------------


System Temperature :25℃/77℉

CPU Temperature :32℃/91℉

CPU Fan Speed :4000 RPM

VcoreA :1.161V

← Select Screen

↑↓ Select Item

+- Charge Field

F1 General Help

F10 Save and Exit

ESC Exit

+1.5Vin :1.569 V

+3.3Vin :3.360V

+5.0Vin :5.187 V


System Temperature:

Show you the current system temperature.

CPU Temperature:

Show you the current CPU temperature.

CPUFAN Speed:

Show you the current CPU Fan operating speed.

3.4.6 AHCI Configuration

BIOS SETUP UTILITY

Advanced

AHCI Setting

General ACPI

Configuration

settings

← Select Screen

↑↓ Select Item

Enter Go to sub screen

F1 General Help

F10 Save and Exit

ESC Exit

► General ACPI Configuration

► Advanced ACPI Configuration

► Chipset ACPI Configuration


3.4.7 MPS Configuration

BIOS SETUP UTILITY


Advanced

MPS Configuration Select MPS

Revision

← Select Screen

↑↓ Select Item

+- Charge Field

F1 General Help

F10 Save and Exit

ECS Exit

MPS Revision [1.4]


MPS Revision:

[1.4]

[1.1]

3.4.8 PCI Express Configuration

BIOS SETUP UTILITY

Advanced

PCI Express Configuration Enables/Disables

PCI Express Device

Relaxed Ordering

← Select Screen

↑↓ Select Item

+- Charge Field

F1 General Help

F10 Save and Exit

ESC Exit

Relaxed Ordering [Auto]

Maximum Payload Size [Auto]

Extended Tag Field [Auto]

No Snoop [Auto]

Maximum Read Request Size [Auto]

Active State Power Management [Disabled]

Extended Synch [Auto]


Relaxed Ordering:

[Auto]

[Disabled]


[Enabled]

Maximum Payload Size:

[Auto]

[128 Bytes]

[256 Bytes]

[512 Bytes]

[1024 Bytes]

[2048 Bytes]

[4096 Bytes]

Extended Tag Field:

[Auto]

[Disabled]

[Enabled]

No Snoop:

[Auto]

[Disabled]

[Enabled]

Maximum Read Request Size:

[Auto]

[Disabled]

[Enabled]

Active State Power Management:

[Disabled]

[Enabled]

Extended Synch:

[Auto]

[Disabled]

[Enabled]

3.4.9 Smbios Configuration

BIOS SETUP UTILITY

Advanced

Smbios Configuration SMBIOS SMI Wrapper

Support for PnP Func

50h-54h

← Select Screen

Smbios Smi Support [Enabled]


↑↓ Select Item

+- Charge Field

F1 General Help

F10 Save and Exit

ESC Exit


Smbios Smi Support:

[Enabled]

[Disabled]

3.4.10 USB Configuration

BIOS SETUP UTILITY

Advanced

USB Configuration Enables support for

legacy USB.ATUO

option disables

legacy support if

no USB devices are

connected

← Select Screen

↑↓ Select Item

+- Charge Field

F1 General Help

F10 Save and Exit

ESC Exit

Module Version – 2.24.5-14.4

USB Devices Enabled :

1Keyboard

Legacy USB Support [Enabled]

USB2.0 Controller Mode [Fullspeed]

BIOS EHCI Hand-Off [Enabled]

USB 3.0 Controller Mode [Enabled]

BIOS XHCI Hand-off [Enabled]

Hotplug USB FDD Support [Auto]

►USB Mass Storage Device Configuration


Legacy USB Support:

[Enabled]

[Disabled]

USB2.0 Controller Mode:

[FullSpeed]

[HiSpeed]


BIOS EHCI Hand-Off:

[Enabled]

[Disabled]

USB 3.0 Controller Mode:

[Enabled]

[Disabled]

BIOS XHCI Hand-off:

[Enabled]

[Disabled]

Hotplug USB FDD Support:

[Auto]

[Enabled]

[Disabled]

USB Mass Storage Device Configuration:

USB Mass Storage Reset Delay [20 Sec]

[10 Sec]

[30 Sec]

[40 Sec]

Device #1 USB Hotplug FDD

Emulation Type [Auto]

3.5 Advanced PCI/PnP Settings

This part describes configurations to be made on PCI bus system. PCI, namely

Personal Computer Interconnect, is a computer bus that allows I/O device to operate

nearly as fast as CPU in its own way. Some technical terms will be mentioned here. We

recommend that non-professional users not make changes from factory default

settings.

BIOS SETUP UTILITY

Main Advanced PCIPNP Boot Security Chipset Exit

Advanced PCI/PnP Settings Clear NVRAM during

System Boot.

WARNING: Setting wrong values In below

sections

may cause system to malfunction.

Clear NVRAM [No]

Plug & Play O/S [No]

PCI Latency Timer [64]

Allocate IRQ to PCI VGA [Yes]

Palette Snooping [Disabled]


PCI IDE BusMaster [Disabled]

← Select Screen

↑↓ Select Item

+- Charge Field

F1 General Help

F10 Save and Exit

ESC Exit

OffBoard PCI/ISA IDE Card [Auto]

IRQ3

[Available]

IRQ4

[Available]

IRQ5

[Available]

IRQ7

[Available]

IRQ9

[Available]

IRQ10

[Available]

IRQ11

[Available]


Clear NVRAM:

[No]

[Yes]

Plug & Play OS:

[No]

[Yes]

PCI Latency Timer:

[64]

[32] [96] [128] [160] [192] [224] [248]

Allocate IRQ to PCI VGA:

[Yes]

[No]

Palette Snooping:

[Disabled]

[Enabled]

PCI IDE BusMaster:

[Disabled]


[Enabled]

OffBoard PCI/ISA IDE Card:

Some PCI IDE cards may require this to be set to the PCI slot number that is

holding the card. Auto:Works for most PCI IDE Cards.

[Auto]

[PCI Slot1]

[PCI Slot2]

[PCI Slot3]

[PCI Slot4]

[PCI Slot5]

[PCI Slot6]

IRQ3/4/5/7/9/10/11/14/15:

[Available]

[Reserved]

Available: Specified IRQ is available to be used by PCI/PnP devices.

Reserved: Specified IRQ is reserved for use by legacy ISA devices.

DMA Channel 0/1/3/5/6/7:

[Available]

[Reserved]

Available: Specified DMA is available to be used by PCI/PnP devices.

Reserved: Specified DMA is reserved for use by legacy ISA devices.

Reserved Memory Size:

Size of memory block to reserve for legacy ISA devices.

[Disabled]

[16k]

[32k]

[64k]

3.6 Boot Settings

BIOS SETUP UTILITY


Boot Settings Configure Settings

During System Boot.

► Boot Setting Configuration

► Boot Device Priority

► Hard Disk Drives


← Select Screen

↑↓ Select Item


F1 General Help

F10 Save and Exit

ESC Exit


Boot Setting Configuration：

Quick Boot:

[Enabled]

[Disabled]

Allows BIOS to skip certain tests while booting .This will decrease the time

needed to boot the system.

Quiet Boot:

[Disabled]

[Enabled]

Disabled: Displays normal POST messages.

Enabled: Displays OEM logo instead of POST messages.

AddOn ROM Display Mode:

Set display mode for Option ROM.

[Force BIOS]

[Keep Current]

Bootup Num－Lock:

Select Power-on state for Numlock.

[On]

[Off]

PS/2 Mouse Support:

Select support for PS/2 Mouse.

[Auto]

[Enabled]

[Disabled]

Wait For „F1‟ If Error:

Wait for F1 key to be pressed if error occurs.

[Enabled]


[Disabled]

Hit „DEL‟Messgae Display :

Displays “press” DEL to run Setup in POST.

[Enabled]

[Disabled]

Interrupt 19 Capture:

Enabled: Allows option ROMs to trap interrupt 19.

[Disabled]

[Enabled]

Boot Device Priority:

Specifies the Boot Device Priority sequence.

Hard Disk Devices :

Specifies the Boot Device Priority sequence from available Hard Drives.

3.7 Security Settings

BIOS SETUP UTILITY


Security Settings Install or Change the

password.

← Select Screen

↑↓ Select Item

Enter Charge

F1 General Help

F10 Save and Exit

ESC Exit

Supervisor Password :Not Installed

User Password :Not Installed

Change Supervisor Password

Change User Password

Boot Sector Virus Protection [Disabled]


Change Supervisor Password:


Install or Change the password.

Change User Password:

Install or Change the password.

Password Check:

[Setup]

[Always]

Setup: Check password while invoking setup.

Always: Check password while invoking setup a well as on each boot.

Boot Sector Virus Protection:

[Disabled]

[Enabled]

Enabled / Disabled Boot Sector Virus Protection.

Type the password with up to 6 characters and then press Enter key. This will

clear all previously typed CMOS passwords. You will be requested to confirm the

password. Type the password again and press Enter key. You may press Esc

key to abandon password entry operation.

To clear the password, just press Enter key when password input window pops up.

A confirmation message will be shown on the screen as to whether the password will

be disabled. You will have direct access to BIOS setup without typing any password

after system reboot once the password is disabled.

Once the password feature is used, you will be requested to type the password each

time you enter BIOS setup. This will prevent unauthorized persons from changing

your system configurations.

Also, the feature is capable of requesting users to enter the password prior to system

boot to control unauthorized access to your computer. Users may enable the feature

in Security Option of Advanced BIOS Features. If Security Option is set to System,

you will be requested to enter the password before system boot and when entering

BIOS setup; if Security Option is set to Setup, you will be requested for password for

entering BIOS setup.


3.8 Advanced Chipset Settings

BIOS SETUP UTILITY


Advanced Chipset Settings Configure North Bridge

feature

← Select Screen

↑↓ Select Item


F1 General Help

F10 Save and Exit

ESC Exit

WARNING: Setting wrong values in below

sections

may cause system to malfunction

► North Bridge Configuration

► South Bridge Configuration


Note: Due to limited address length of BIOS, only a portion of panel parameters are listed in

BIOS Setup. If the connected panel is not included in the parameter list, display

problem will occur. In this case, Please do not change BIOS setup.

3.8.1 North Bridge Configuration

BIOS SETUP UTILITY

Chipset

North Bridge Chipset Configuration Options

Auto

Max MHz

← Select Screen

↑↓ Select Item

+- Charge Field

PCI MMIO Allocation: 4GB To 3072MB

DRAM Frequency [Auto]

Gongigure DRAM Timing by SPD [Enabled]

Initate Graphic Adapter [IGD]

Initate Graphic Mode Select [Enabled,

8MB]

PEG Port Configuration


► Video Function Configuration F1 General Help

F10 Save and Exit

ESC Exit


DRAM Frequency:

[Auto]

[Max Mhz]

Gongigure DRAM Timing by SPD:

[Enabled]

[Disabled]

Initate Graphic Adapter:

Select which graphics controller to use as the primary boot device.

[IGD]

[PCI/IGD]

[PCI/PEG]

[PEG/IGD]

[PEG/PCI]

Initate Graphic Mode Select:

[Enabled, 8MB]

Video Function Configuration:

BIOS SETUP UTILITY

Chipset

Video Function Configuration Options

Fixed Mode

DVMT Mode

← Select Screen

↑↓ Select Item

DVMT Mode Select [DVMT

Mode]

DVMT/FIXED Memory

[256MB]

Boot Display Device

[VBIOS-Default]

Flat Panel Type [1024x768

LVDS]

Backlight Control Support

[VBIOS-Default]


Panel Backlight Control [Level 9] +- Charge option

F1 General Help

F10 Save and Exit

ESC Exit


DVMT Mode Select:

[DVMT Mode]

[FIXED Mode]

DVMT/FIXED Memory Size:

[256MB]

[128MB]

[Maximum DVMT]

Boot Display Device:

[VBIOS-Default]

[CRT]

[LVDS]

[CRT + LVDS]

Flat Panel Type:

[1024x 768 LVDS]

[640x480 LVDS]

[800x600 LVDS]

[1280x1024 LVDS]

[1400x1050 LVDS]

[1600x 1200 LVDS]

Panel Backlight Control :

[Level9]

[Level0]

[Level1]

[Level2]

[Level3]

[Level4]

[Level6]

[Level7]


[Level8]

[Level9]

[Level10]

[Level11]

[Level12]

[Level13]

[Level14]

[Level15]

Note: Panel support PWM Function.

3.8.2 South Bridge Configuration:

BIOS SETUP UTILITY

Chipset

South Bridge Chipset Configuration Options

Disabled

2 USB Ports

4 USB Ports

6 USB Ports

8 USB Ports

← Select Screen

↑↓ Select Item

+- Charge Field

F1 General Help

F10 Save and Exit

ESC Exit

USB Functions [8 USB

Ports]

USB2.0 Controller [Enabled]

82574lan1 boot [Disabled]

Lan Wakeup [Disabled]

HAD Controller [Enabled]

SMBUS Controller [Enabled]

SLP_S4# Min. Assertion Width [1 to 2

Seconds]

Restore on AC Power loss [Power off]

PCIE Ports Configuration

PCIE Port 1 [Auto]

82574LAN1 [Auto]

Capture Card [Auto]

Mini-PCIE [Auto]

PCIE Port 5 [Auto]

PCIE Port 6 [Auto]



USB Functions:

[8 USB Ports]

[Disabled]，

[2 USB Ports]

[4 USB Ports]

[6 USB Ports]

USB 2.0 Controller:

[Enabled]

[Disabled]

82574lan1 boot:

[Enabled]

[Disabled]

Lan Wakeup:

[Disabled]

[Enabled]

HDA Controller:

[Enabled]

[Disabled]

SMBUS Controller:

[Enabled]

[Disabled]

SLP_S4# Min. Assertion Width:

[1 to 2 Seconds]

[4 to 5 Seconds]

[3 to 4 Seconds]

[2 to 3 Seconds]

Restore on AC Power Loss:

[Power Off]

[Power On]

[Last Status]

PCIE Ports Configuration:

PCIE Port 1:


[Auto]

[Enabled]

[Disabled]

82574LAN1:

[Auto]

[Enabled]

[Disabled]

Capture Card:

[Auto]

[Enabled]

[Disabled]

Mini-PCIE:

[Auto]

[Enabled]

[Disabled]

PCIE Port 5:

[Auto]

[Enabled]

[Disabled]

PCIE Port 6:

[Auto]

[Enabled]

[Disabled]

3.9 Exit Options

BIOS SETUP UTILITY


Exit Options Exit system setup

after saving the

changes

F10 key can be used

For this operation

Save Changes and Exit

Discard Changes and Exit

Discard Changes

Load Optimal Defaults

Load Failsafe Defaults


← Select Screen

↑↓ Select Item


F1 General Help

F10 Save and Exit

ESC Exit

V02.61 © Copyright 1985-2006 American Mega trends , Inc.

Save Changes and Exit:

Save configuration changes and exit setup?

(F10 key can be used for this operation)

[OK]

[Cancel]

Discard Changes and Exit:

Discard Changes and Exit setup?

(ESC key can be used for this operation)

[OK]

[Cancel]

Discard Changes:

Discard changes?


[OK]

[Cancel]

Load Optimized Defaults:

Load Optimized Defaults?


[OK]

[Cancel]

Load Fail-Safe Defaults:

Load Fail-Safe Defaults?


[OK]

[Cancel]


Chapter 4 Installation of Drivers

This chapter describes the installation procedures for software and drivers under the windows XP. The

software and drivers are included with the motherboard. The contents include Intel chipset driver,

VGA driver, LAN drivers, Audio driver, Capture driver.

Installation instructions are given below.

I

Important Note:

After installing your Windows operating system (Windows XP), you must install

first the Intel Chipset Software Installation Utility before proceeding with the

installation of drivers.


4.1 Intel Chipset Driver

To install the Intel chipset driver, please follow the steps below.

Step 1. Select Intel(R) Chipset Atom D525 + Intel ICH8M from the list

Step 2. Click Next to setup program.


Step 3. Read the license agreement. Click Yes to accept the terms of the license agreement.

Step 4. Click Next to continue.


Step 5. Click Next.

Step 6. Select Yes, I want to restart this computer now. Click Finish then remove any installation

media from the drivers.


4.2 Intel Graphics Media Accelerator Driver

To install the VGA drivers, follow the steps below to proceed with the installation.

Step 1. Select Intel (R) GMA 3150 VGA Chipset.



Step 3. Click Next.

Step 4. Read the license agreement. Click Yes to accept license agreement.


Step 5. Click Next.



Step 7. Select Yes, I want to restart this computer now. Click Finish then remove any installation

media from the drives.

4.3 Intel(R) 82574L Network Adapter

To install the Intel (R) 82574L Network Adapter connect device driver, please follow the steps below.

Step 1. Select Intel (R) 82574L Network Adapter from the list



Step 3. Read the license agreement. Select I accept the terms in the license agreement then click

Next to continue.


Step 4. Select Drivers, Intel(R) PROSet for Windows* Device Manager, Advanced Network

Services. Click Next to continue.

Step 5. Click Install to begin installation.


Step 6. Click Finish to complete the installation.

4.4 Realtek HD Audio Driver Installation

To install the Realtek High Definition (HD) Audio driver, please follow the steps below.

Step 1. Select Realtek ALC662 HD Audio Driver from the list


Step 2. Click Next to continue the installation.

Step 3. Click Yes.


Step 4. Wait for installation.

Step 5. Select Yes, I want to restart my computer now. Then click OK.


4.5 Capture Driver Installation

To install Capture driver, please follow the steps below.

Step 1. Select Capture Driver.

Step 2. Click Properties.


Step 3. Under Hardware, click Device Manager.

Step 4. Select Mutimedia video controller, click update driver.


Step 5. Select No, not this time. Click Next.

Step 6. Select Install from a list or specific location(Advanced).


Step 7. Select Don’t search. I will choose the driver to install. Then click Next.

Step 8. Select Show All Devices. Click Next.


Step 9. Select Standard CD-ROM drives. CD-ROM Drive(force CDDA accurate)

Step 10. Install From Disk screen appears.

Step 11. Click Browse. Select D:\Driver CD\AthenaWdfDrv_7.0.101.0


Step 12. Select Conexant CX25821 WDF Video Capture (Athena). Click Next.

Step 13. Click Yes to continue.

Step 14. Click Finish.


Step 15. Conexant CX25821 WDF Video Capture(Athena) has been installed.

Documents

AWK-4630 Workstation...ACS-2907 User Manual 7 1.3 Brief Description of ACS-2907 ACS-2907 is a Fan-less wall mounting and ultra-compact standalone Box PC, powered by an Intel Atom D525