AW DRIVE FASTENERSExclusive Fasteners Featuring The Unique Wurth AW Drive

2 WURTH AUSTRALIA PTY. LTD.

The unique Wurth AW Drive System gives you more power whilst maximising efficiency. Thanks to the 5 sizes, you can be assured of a tight and secure fit to the fastener each and every time.

+Advantages of Phillips:• Good centring• Location• Good positioning

Advantages of TX:• Power transmission• No come-out effect

The AW® drivecombines the advantages of both systems

=

DRIVE SYSTEM

MORE POWER• Optimum transmission of power• Firm fit that does not require magnets• Fast location• Secure settling of the screw• Almost no unscrewing of the bit• No wobbling• Does not damage the surface coating of

the screw• Only five bit sizes for the diameters

3.0 to 12.0 mm

3WURTH AUSTRALIA PTY. LTD.

1/4" & 5/16” AW Drive Bits

Example - Actual Size

Drive Type SizeArt. No.25/32mm

Art. No.50mm

Art. No.70/73mm

Art. No.100/110mm

Art. No.176mm

1/4"

AW® 10 0614 511 0 0614 521 0 0614 571 0 0614 581 0 -

AW® 20 0614 512 0 0614 522 0 0614 572 0 0614 582 0 0614 100 420

AW® 25 0614 512 5 0614 522 5 - 0614 582 5 -

AW® 30 0614 513 0 0614 523 0 0614 573 0 0614 583 0 -

AW® 40 0614 514 0 0614 524 0 0614 574 0 - -

32mm

73mm

110mm

AW Drive Bits • Improved power transmission.• Longer life of recess and drive due to optimal fit.• Multiple sprockets allow improved alignment.• Fasteners can be held in place using no magnetism.• Ability to work with one hand with AW drive.

Catalogue Page 12 1681/2

50mm

176mm

4 WURTH AUSTRALIA PTY. LTD.

AMO III Screw

Cat. Page 06 2063-4/6

Blue Zinc Passivated, A2KType 1 with AW30 Head dia. 12.0 mm

Type 2 with AW30/AW40 Head dia. 8.0 mm/11.5mm

Type 3 with AW30 Head dia. 12.5 mm

Type 4 with washer Head AW40 7.5 x 102 mm, head dia. 21 mm

Flush Head, 8.0 mm - A2KWasher Head, 12.5 mm - A2K

Anchor DimensionsTotal Length

Head Dia. Art. No.A2K Blue Zinc Passivated

P. Qty

52 Type 1 with AW®3012.0Suitable application: Light countersinking with wood and plastic profiles

0234 730 5272 0234 730 72

200

102 0234 730 102152 0234 730 15272 Type 2 with AW®30

Head diameter 8.0 mm

Suitable application: Preferably for use in concrete surface with the frame materials wood and plastic

0234 830 7282 0234 830 82

102 0234 830 102

72 Type 3 with AW®30Head diameter 12.5 mm

Suitable application: Thanks to the large flat head, the head makes clean contact on window profiles, providing advantages when using cover capsSuitable cover caps: Art. No. 0590 790 …

0234 930 72102 0234 930 102

152 0234 930 152

102

7.5mm Screw Diameter with AW40Head diameter 21.0mm

5936 000 001 50l

Performance Data

Anchor type Type 1 - 7.5 mm Type 2 - 7.5 mm Type 3 - 7.5 mm Type 2 - 11.5 mm

Fire resistance durationConcrete strength class at least 20MPa and maximum 50MPa

Centered tensile load

F30 [in kN] 0.80 – 0.80 –

F60 [in kN] 0.55 – 0.55 –

F90 [in kN] 0.45 – 0.45 –

F120 [in kN] 0.40 – 0.40 –

Shear or oblique pull up to 30°

F30 [in kN] 0.50 0.50 0.50 0.50

F60 [in kN] 0.50 0.50 0.50 0.50

F90 [in kN] 0.50 0.50 0.50 0.50

F120 [in kN] 0.50 0.50 0.50 0.50

Drill bit nominal diameter

Concrete d0 [mm] 6.5 10.0

Chalky sandstone, solid brick, vertically perforated brick (at least 2 walls), pumice, light con-crete

6.0 10.0

Aerated concrete No pre-drilling necessary

5WURTH AUSTRALIA PTY. LTD.

Zebra Pias Countersunk Head

Nominal Ø d 4.2 4.8Head Ø dk 8.1 9.5k 3.4 4.0 lp 3.7 4.5 Drive Size AW® 20 AW® 25

Drilling Area 1.75–3.0 1.75–4.0Standard values for working 1,700–2,500 min-¹ 1,200–1,800 min-¹

* Contact pressure: 10 N; if necessary use a depth stop

Nominal ømm

Length lmm

Drive Size ZN Pack Qty.Art. No.

4.2

13

AW20

0205 42 13

100/100016 0205 42 1619 0205 42 1925 0205 42 25

4.8

16

AW 25

0205 48 16

100/50019 0205 48 1922 0205 48 2225 0205 48 2532 0205 48 32

Cat. Page 06 3681

Quicker than any twist drill. Reduces assembly costs by 50%.With Zebra Pias Screws you can work in the same way as with common twist drills. You form the thread and simply screw in. All in one operation. This gives you considerable advantages.

Zebra Pias Pan Head – Assortment

Zebra Pias Pan Head AW Drive Zinc (A3K)Contents: 16 Sizes from 3.5 x 9.5 - 4.8 x 25mm = 1,603 pieces

Art. No. 5964 020 600 Cat. Page 10 2008

Caps For Zebra PiasNominal Ømm

dmm

Grey Black White Pack Qty. Art. No. Art. No. Art. No.

4.2 16 0202 001 42 0202 001 421 0202 001 42250

4.8 19 0202 001 48 0202 001 481 0202 001 482

Cat. Page 06 3642

6 WURTH AUSTRALIA PTY. LTD.

Zebra Pias Pan Head Zinc & A2

Nominal Ø d 3.5 3.9 4.2 4.8

Head Ø dk 6.6 7.3 8.0 9.5

k 3.0 3.75 3.75 3.85

lp 3.0 3.1 3.7 4.5

Drive AW® 10 AW® 20 AW® 20 AW® 25Drilling Area 0.7–2.25 0.7–2.4 1.75–3.0 1.75–4.0

Standard Values for working

Speed (without load)*1,700–2,500 min-¹ 1,200–1,800 min-¹

* Contact Pressure: 10 N; if necessary use a depth stop

Cat. Page 06 3641

Nominal ømm

Length Lmm

DriveSize

ZINC A2 Pack Qty.Art. No. Art. No.

3.5

9.5

AW 10

0206 35 95 -

100/1000

13 0206 35 13 0206 135 1316 0206 35 16 0206 135 1619 0206 35 19 0206 135 1925 0206 35 25 0206 135 2516

AW 20

- 0206 139 1619 - 0206 139 1925 - 0206 139 25

3.9

13 0206 39 13 -16 0206 39 16 -19 0206 39 19 -25 0206 39 25 -

4.2

13 0206 42 13 0206 142 1316 0206 42 16 0206 142 1619 0206 42 19 0206 142 1922 0206 42 22 0206 142 2225 0206 42 25 0206 142 2532 0206 42 32 -

4.8

13

AW 25

0206 48 13 0206 148 1316 0206 48 16 0206 148 1619 0206 48 19 0206 148 1922 0206 48 22 0206 148 2225 0206 48 25 0206 148 25

100/50032 0206 48 32 0206 148 3238 0206 48 38 0206 148 3845 0206 48 45 -50 0206 48 50 0206 148 50

Quicker than any twist drill. Reduces assembly costs by 50%.

With Zebra Pias Screws you can work in the same way as with common twist drills. You form the thread and simply screw in. All in one operation. This gives you considerable advantages.

7WURTH AUSTRALIA PTY. LTD.

Wing Pias® Self Drilling Screws

Nominal dia. d in mm 6.3Head dia. dk max. in mm 12Drive AW® 30

Drilling and attachment thickness lU (steel) in mm 2.0 – 6.0

The self-drilling screw that offers up to a 50% time saving when fastening wood to metal sub-structures.

• Steel, LAFRE® silver grey-coated.• Cr(6)-free corrosion protection, ap-

prox. 500 h no base-metal corrosion (salt-spray mist test as per DIN EN ISO 9227 – NSS).

• Countersunk milling head for process-ing hard and soft woods.

Cat. Page 06 3689

Nominal dia. d

Lengthl

Max. woodthickness* lH

Head dia. dk

12mmPack Qty.

in mm in mm in mm Art. No.

6.3

55 35 0219 864 55

250/50065 45 0219 864 6580 60 0219 864 80100 80 0219 864 100

*The recommendation for the maximum wood thickness lH was calculated based on the maximum attachment thickness lU of the substructure!

The powerful, self-drilling range of screws offer customers up to 50% time saving when fastening wood to metal sub-structures.

Wurth Wing Pias Screws feature:• The specially designed ‘wings’ cut the thread in wood and break-off upon contact with the metal.• The first few turns of the screw cuts the thread, then the remainder of the screw fastens into the substrate.• Enhanced power with force feeding of the screw, achieved by the wings drilling out the wood for a smooth

process.

INTRODUCING WURTH WING PIAS...

Advanced drilling tip for clean drilling of both metal and timber.

Especially designed wings break-off upon contact with the metal.

Special tapping screw thread. Countersunk head with milling ribs.

8 WURTH AUSTRALIA PTY. LTD.

Wing Pias® Countersunk Head

Nominal dia. d in mm 3.9 4.8 5.5

Head dia. dk max. in mm 7.5 9.5 10.8

Drilling tip length lp in mm 8 9 11

Drive AW® 20 AW® 25 AW® 25Drilling range (steel) in mm 1.5 - 2.4 2.0 - 4.0 2.0 - 5.0

Nominaldia. d mm

Lengthl mm

Max. attachment length*lB mm

Art. No. Pack Qty.

3.9 28 14 0215 883 928

50038 24 0215 883 938

4.838 21 0215 884 83844 27 0215 884 844

5.555 35 0215 885 555

25065 45 0215 885 56590 70 0215 885 590

Non-rusting A2 drilling screw with a case hardened drilling tip.

• Drilling out of the wood by the wing prevents forced advancement of the screw.

• Drilling of the core hole in the sub-structure. Breakage of the wing upon contact with the metal.

• First few threads of the screw cut the thread, into which the screw then turns.

Cat. Page 06 3690* Wood thickness lH and sub-structure thickness lU = max. attachment length lB

Wing Pias® Countersunk Head

Nominal dia. d in mm 3.9 4.2 4.8 5.5 6.3

Head dia. dk max. in mm 7.5 8 9.5 10.8 12.4

Drive AW20 AW20 AW25 AW25 AW30Drilling and attachment thickness lU (steel) in mm 1.5–2.4 1.75–3.0 2.0–4.0 2.0–5.0 2.0–6.0

The self-drilling screw with up to 50% time savings when fastening wood to metal sub-structures. Steel, yellow galvanised.

• With tapping screw thread.• Countersunk milling head for

processing hard and soft woods.• AW® drive for optimum force

transmission and care of the corrosion protection.

Nominal dia. d in mm

Length l in mm

Max. wood thickness* lH in mm Art. No.

P. Qty.

3.925 13 0219 113 925

500

32 20 0219 113 93238 26 0219 113 938

4.232 20 0219 114 23238 26 0219 114 23850 38 0219 114 250

4.832 19 0219 114 83238 25 0219 114 83850 37 0219 114 850

5.538 23 0219 115 53845 30 0219 115 54550 35 0219 115 550

6.3 65 49 0219 116 365*The recommendation for the maximum wood thickness lH was calculated based on the maximum attachment thickness lU of the substructure!Storable in ORSY®

Cat. Page 06 3693

9WURTH AUSTRALIA PTY. LTD.

Wing Pias® Countersunk Head

Wing Pias® Plate Countersunk Head

Nominaldia. din mm

Lengthlin mm

Max. fasteninglength lB

in mm

Art. No. Pack. Qty.

6.355 33 0219 063 55

25065 43 0219 063 65

Nominal dia. d in mm 6.3Head dia. max. dk in mm 20Drilling tip length lp in mm 15Drive AW 30Drilling range (steel) in mm 2.0 - 6.0

Nominaldia. din mm

Lengthlin mm

Max. fasteninglength lB

in mm

Art. No. Pack. Qty.

8

65 33 0219 008 6525080 48 0219 008 80

100 68 0219 008 100

Nominal dia. d in mm 8Head dia. max. dk in mm 15Drilling tip length lp in mm 18Drive AW 40Drilling range (steel) in mm 3.0 - 12.0

Note: Wing pias® have to be appropriately tested for usability before each application.Use only application equipment with depth stop and claw clutch.

Note: Wing pias® have to be appropriately tested for usability before each application.Use only application equipment with depth stop and claw clutch.

With milling ribs and drive

Steel, Ruspert®-coated (grey)Tapping screw thread.

With milling ribs for soft and hard wood on steel substructures.

The self-tapping screw for fastening wood to steel substructures.

Advantage: Corrosion protection Ruspert® - coated approx. 500 h no base metal corrosion as per DIN EN ISO 9227 – NSS (electro-galv. - approx. 48 h)

Galvanized drilling screws may only be used where dampness is not to be expected.

With milling ribs and drive

Steel, Ruspert®-coated (grey)

With milling ribs for soft and hard wood on steel substructures.

The self-tapping screw for fastening wood to steel substructures.

Advantage: Corrosion protection Ruspert® - coated approx. 500 h no base metal corrosion as per DIN EN ISO 9227 – NSS (electro-galv. - approx. 48 h)

Galvanized drilling screws may only be used where dampness is not to be expected.

Cat. Page 06 3693

Cat. Page 06 3693

10 WURTH AUSTRALIA PTY. LTD.

Connects the wood instead of splitting it!

• Reduce the splitting effect! • Ring thread, double-threaded (D = 3.0–4.5 mm)• Counter thread, coarse thread (D = 5.0–12.0 mm)• Minimal splitting forces, especially when screw in at edges• Reduction of screw-in torque• Blow-outs are avoided to a high degree thanks to punching effect of ring thread

Countersink cleanly anywhere!• Suitable for wood and fittings• No damaging of coated wood surfaces• Chips that occur due to screwing into the surface are picked up

Make screwing in easier!• Minimal screw-in torque thanks to asymmetrical thread• High over-turning force (more force must be used to turn

screw excessively)• Faster screwing in than with conventional particle board screws thanks to

asymmetrical thread

ASSY® 3.0 Standard particle board screw

ASSY® 3.0 Standard particle board screw

ASSY® 3.0 Standard particle board screw

Z-9.1-361

With general

construction permit

Z-9.1-514

With general

construction permit

ASSY® 3.0dia. 4.0-4.5 mm

ASSY® 3.0dia. 5.0-12.0 mm

AW® drive – offering more power• 5 bit sizes for the diameters

3.0 to 12.0 mm

Milling pockets – can be countersunk anywhere!Fewer chips • Suitable for wood and fittings• Minimal damage to coated wood surfaces• Fewer chips on surface

Asymmetric thread – faster speed• Low screw-in torque• High over-turning force • Faster screwing in than conventional

particle board screws• Double-threaded: 3.0–4.5 mm,

Coarse thread: 5.0–12.0 mm

Ring/Counter thread – less tendency of the wood to split, very few blow-outs(Ring thread = 3.0–4.5 mm, Counter thread = 5.0–12.0 mm)• Minimal splitting forces, especially when screw in at edges • Reduction of the screw-in torque • Blow-outs are avoided to a high degree thanks to punching effect of ring thread

End millThe "auxiliary motor" for low force (from dia. = 5 mm, L = 70 mm)• Minimizing of the screw-in and head countersinking torque,

especially with long screws • Protection of screw-in tools

ETA-11/0190

INTRODUCING WURTH

11WURTH AUSTRALIA PTY. LTD.

Asymmetric thread – faster speed• Low screw-in torque• High over-turning force • Faster screwing in than conventional

particle board screws• Double-threaded: 3.0–4.5 mm,

Coarse thread: 5.0–12.0 mm

ASSY® PLUS A2 Performance Decking Construction Screw

ASSY® PLUS A2/A4 Decking Construction Screw

dmm

L mm

lgmm

dhmm

Drive A2/304 Pack Qty.Art. No.

5.550 18

6.8 AW 200166 215 550

25070 23 0166 215 570 Cat. Page 06 3721

ETA-11/0190

Visually clean look

Under head thread

The screw for fastening decking boards. The under-head thread permanently secures the decking board to the supporting construction. Many types of wood can be processed without pre-drilling thanks to the drill tip. Pre-drilling is recommended for hardwoods.

• Permanent screw coupling, clean look.

• Precise positioning and no splitting.

• Clean and easy countersinking.

dmm

L mm

bmm

dkmm

Drive A2/304 P. Qty. A4/316 P. Qty.Art. No. Art. No.

5.550 27

7.5AW 20

0166 115 550 1,000 0169 015 550250

70 37 0166 115 570 250 0169 015 570

Container for 50mm A2/304 Decking Screw. Holds 1,000 screws.

Cat. Page 06 3722

The screw for fastening decking boards. Many types of wood can be processed without pre-drilling thanks to the drilling tip.

ETA-11/0190

12 WURTH AUSTRALIA PTY. LTD.

ASSY® Plus Special / ASSY® Plus Special A2

The self-drilling screw designed for timber.• Maximum power transmission.• No wobbling effect.• Countersunk head with milling pockets.• Single-flight asymmetrical thread.• Spade drilling tip.

dh

l

b

lg

d

dmm

lmm

lgmm

bmm

dhmm

Drive Zinc A2/304

Pack Qty.

Art. No. Art. No.

4.0

30 18 21

7.9A

W® 2

0

0165 914 030 -

500

35 23 26 0165 914 035 -40 23 26 0165 914 040 -45 25 28 0165 914 045 -50 30 33 0165 914 050 -

4.540 22 26

9.0- 0166 914 540

50 29 33 - 0166 914 55070 44 48 - 0166 914 570 200Cat. Page 06 3711

ETA-11/0190

ASSY® Plus A2 Cladding Screw

The ASSY Plus Cladding screw is ideal for most timber facades.

Material: Stainless Steel A2/304.

Optimised Head shape• Top Head.• 60o counter sunk head with milling pockets.• Small head diameter.

Geometrical optimised drill tip• Quick and safe setting.• No cracking.• No damage to coated wood materials.• No pre-drilling required in most hard woods.

Cat. Page 06 3712

Ømm

lmm

lgmm

bmm

dkmm

Drive A2/304 Pack Qty.Art. No.

3.5 50 26 30 5.5 AW® 10 0166 533 550 500

l

lg

b

ø

13WURTH AUSTRALIA PTY. LTD.

ASSY® 3.0 SK A2 Partial Thread

Application: The ASSY® 3.0 SK A2 with a large disk head especially suited for photovoltaic/woodworking/carpentry trades for screw connections outdoors, for humid rooms and salty atmospheres.

Tip: The 30° tip enables precise starting. Screw with ring thread in tip area, which greatly reduces the splitting forces of the wood, especially in the edge area. The screw-in torque is considerably less than with conventional particle board screws and extends the service life of the processing machine and the bit insert.

Thread: Easy screwing in thanks to asymmetrical entry thread.

End mill: The end mill after the thread reduces the screw-in torque by 20 %.

Head: Large disk head with AW® drive.• Optimum power transmission.• Optimum centering.• Long service life.• Even distribution of power prevents the surface

coating from being damaged.

Material: Corrosion-resistant, austenitic stainless steel A2 (1.4301, 1.4567).

d in mm

l in mm

lg in mm

dh Drive Art. No. A2/304

P. Qty.

8.0160

80 18.9 AW®40 0181 808 16050

200 0181 808 200

Storable in ®ORSY

Steel Type Short Name

EnvironmentRural Urban Industry Near sea

Material No. N M H N M H N M H N M H

X1NiCrMoCu25-20-5 1.4539 Würth HCR (0159 9..) x x x x x x x x + x x +X5CrNiMo17-12-2 1.4401/1.4578 Würth A4 (0169 005 …) x x x x + + + + (+) + + (+)X5Cr-Ni18-10 1.4301/1.4567 Würth A2 (0166 105 …) + + + + + (+) (+) (+) – + (+) –X6Cr17 1.4016 Many competitors (+) (+) (+) (+) – – (+) – – – – –

The range of applications of the various stainless steels is contained in the following table of the ISER (German Information Office for Rustproof Stainless Steel, Information Leaflet 828). Rustproof stainless steels (e.g. Material No. 1.4016) are recommended there for use in the atmospheric area only for use in a rural environment, and here as well only with great restrictions.

We therefore recommend only using austenitic stainless steels for outdoor applications while taking the environmental conditions into account. The stainless steel A4 (0169 005 …) is especially suitable for use in an industrial atmosphere and for use near the sea.

Stainless steels for various ambient conditions(www.edelstahl-rostfrei.de, Information Leaflet 828)N = Lowest corrosion loading within the respective environment,

characterized, for example, by low temperatures and low humidityM = Medium corrosion loading within the respective environmentH = Higher corrosion loading within the respective environment, e.g. due

to continuously high humidity, high ambient temperatures, especially aggressive air pollution

x = Basically meets the requirements, however less expensive steels could also be sufficient

+ = Probably the best choice of materials with regard to corrosion resistance and costs

(+) = Sufficient colour, provided certain precautionary measures are taken. Smooth surface finishes and regular cleaning are especially important

– = Probably heavy corrosion

Note: Austenitic stainless steel is characterized by a high corrosion-resistance to aggressive industrial air, ocean climate, line, river, sewer and salt water and wood containing tannic acid. It is conditionally resistant to acid and not suitable for atmospheres containing chlorine gas.

Cat. Page 06 3732

14 WURTH AUSTRALIA PTY. LTD.

ASSY® 3.0 A2 Screw

The ASSY® 3.0 A2 of corrosion-resistant, austenitic stainless steel is designed especially for applications outdoors, in damp rooms and in salty atmospheres.

Tip: Ring thread → Minimal splitting effect, especially when screwing in near the edge

Thread: Asymmetrical coarse thread for short screw-in times.

Head: Milling pockets for clean countersinking.

Material: Corrosion-resistant, austenitic stainless steel A2

Driv

e

Countersunk head* w/shaft

d inmm

l inmm

dk inmm

b inmm

A2/304 Pack Qty.Art. No.

6.0

60

12.0

37

AW

® 3

0

0180 106 60

10080 50 0180 106 80100 60 0180 106 100120

700180 106 120

140 0180 106 140 Cat. Page 06 3731

JAMO Plus Screws

Dia. d in mm

l in mm

lg in mm

b in mm

dh in mm

Drive

Art. No. Zinc, Blue Passivated

P. Qty.

6.0 70 33 38

12.0 AW® 300234 465 70

100 90 55 60 0234 465 90110 65 70 0234 465 110

The screw for adjustable changes to spacing after installation. For mounting wood substructures to wood substrates without pre-drilling.

• Drive.• Precise positioning, no rupturing.• Milling pockets for easy and clean

countersinking.• 25% reduction in adjustment time.

Cat. Page 06 3801

Position Jamo screw

Screw down wood lath

1

3

2

Adjust spacing

15WURTH AUSTRALIA PTY. LTD.

ASSY® 3.0 Zinc-Nickel

The Wurth Zinc Nickel surface is highly corrosion resistant and is in line with the Australian Corrosion resistance class 2. (AS. 3566-2).

Attention: Screws may not be used for:• Wood containing large amounts of tannic acid,• Boiler-pressure impregnated wood (treated wood)

ISO 9223 is in accordance with AS 3566-2 (Australian Corrosion Categories)

dia.in mm

Lin mm

bin mm

dkin mm

Drive Endmill

Art. No. PackQty.

6.0

50 32

12.00

AW

® 3

0

with

0170 860 50

100 80 50 0170 860 80100 60 0170 860 100120

700170 860 120

150 0170 860 150

ETA-11/0190

Cat. Page 06 3733

ASSY® 3.0 Combi Screw

dmm

lmm

lgmm

dhdrive

Art. No.Zinc, Blue Passivated

P. Qty.

8.0

80 50

Hexagon Holder SW12 or AW® 40

0184 208 80

75

100 60 0184 208 100

120

80

0184 208 120

140 0184 208 140

160 0184 208 160

200 0184 208 200

240 100 0184 208 240

10.0

80 50

Hexagon Holder SW15 orAW® 40

0184 210 80

50

100 60 0184 210 100

120 80 0184 210 120

160

100

0184 210 160

200 0184 210 200

240 0184 210 240

12.0

100 60

Hexagon Holder17mm orAW® 40

0184 212 100

120 80 0184 212 120

160

100

0184 212 160

180 0184 212 180

200 0184 212 200

240 120 0184 212 240

ASSY® 3.0 combi with hexago-nal head and integrated AW®40 drive is ideal for screw connec-tions in timber substrates includ-ing house fixtures, wood con-struction and carpentry.

• Drive.• 30% saving in time and less tendency

to split during use.

Cat. Page 06 3734

16 WURTH AUSTRALIA PTY. LTD.

ASSY® 3.0 Screw

CountersunkFull thread

Countersunk head With MillingPockets& Shank

Pan head Full Thread

Pack Qty.

Ø L Drive dhmm

lgmm

dhmmmm mm Art. No. Art. No. Art. No.

3.5

16

AW20

6.9

0170 035 16 - - - -

100

25 0170 035 25 - - 7 0153 035 02535 0170 035 35 - - - -40 0170 035 40 - - - -

4.0

12

7.9

0170 040 12 - - - -17 0170 040 17 - - 8 0153 040 01720 0170 040 20 - - - -25 0170 040 25 - - 8 0153 040 02530 0170 040 30 - - - -35 0170 040 35 - - 8 0153 040 03540 0170 040 40 - - - -45 - 29 0170 140 45 8 0153 040 04550 - 29 0170 140 50 - -

4.5

17

8.8

0170 045 17 - - - -20 0170 045 20 - - - -25 0170 045 25 - - 9 0153 045 02530 0170 045 30 - - - -35 - - - 9 0153 045 03540 0170 045 40 - - - -50 - 28 0170 145 50 - -60 - 33 0170 145 60 9 0153 045 060

5.0

20

9.5

- - - 10 0153 050 02040 0170 050 40 - - - -45 0170 050 45 - - 10 0153 050 04550 - 30 0170 150 50 - -60 - 37 0170 150 60 - -70 - 42 0170 150 70* - -100 - 52 0170 150 100* - -

6.0 50 AW30 - - - - 12 0153 060 050

Special asymmetrical thread de-sign for faster screw insertion.

• Finish: Zinc Plated.• Suitable for: All types of hard and

soft woods, MDF, laminated and waterproof chipboards, plywood and other wood based materials.

• Up to 40% higher fracture torque. • 50% time saving over conventional

screw types.

Cat. Page 06 3741

L

17WURTH AUSTRALIA PTY. LTD.

Self drilling tip.

Steel, galvanised (thick-film passivation), Deltacoll-coated.

• Drive: PH2/AW20.• Special thread with needle tip.• Head dia.: 7.0 mm• Increased corrosion protection due to thick-film passivation and

Deltacoll-coating. In the salt-spray mist test according to DIN EN ISO 9227-NSS, 240 hours was achieved without red rust on base metal corrosion.

• Heat-resistance of the corrosion-protection coating: 150°C. Cr(VI)-free corrosion-protection coating.

Drive Nominal dia. in mm

Length L in mm

Art. No. Steel, galv. & Deltacoll-coated

Pack Qty.

PH2

4.1

19 0185 244 119

1,00022 0185 244 12225 0185 244 12530 0185 244 13035 0185 244 13538 0185 244 138 500

AW20

16 0188 144 116 6,00019 0188 144 119 5,00025 0188 144 125 4,00030 0188 144 130 2,50035 0188 144 135 2,000

Can be stored in ORSY® System.

FBS 1, roller-sorted – For use in automatic ma-chinesDrive Nominal

dia. in mm

Length L in mm

Art. No. Steel, galv. & Deltacoll-coated

Pack Qty.

PH2 4.125 0185 294 125 4,00035 0185 294 135 2,000

Can be stored in ORSY® System.Cat. Page 06 3851

FBS Window Construction Screw

WG-Fix Screw Anchor

For fastening curtain rails, baseboards, picture frames, bathroom and kitchen accessories, etc.

• Finish: Zinc Plated (A2K).• Fast, simple installation.• Two head versions – raised countersunk head

for easy, clean countersinking and panhead for large-area contact.

• Universal anchorless screw connection – even on various surfaces, e.g. solid sand-lime brick, clay brick and gypsum plasterboard.

• HiLo thread provides for increased over-turning torque.

• High thread pitch enables fast screw-in speed.

Anchor dimensionsTotal length l [mm] 30 45Max. attachment height tfix [mm] 2.5 16Raised countersunk head Art. No. – 0189 306 345Panhead Art. No. 0189 363 30 –Drive AW20Pack Qty. 250

Characteristic valuesNom. drill dia. d0 [mm] 4.0Drilled hole depth h1 ≥ [mm] 35Through-hole in the component being connected df ≤ [mm] 6.5

Performance dataAnchor diameter 6.3

Recommended working load

Clay brick MzFrec [kN]

0.23Solid sand-lime brick KSV 0.43Gypsum plasterboard d ≥ 9.5 mm 0.01

70

Cat. Page 06 2185

18 WURTH AUSTRALIA PTY. LTD.

Countersink With Depth Stop

DescriptionDia. in mm

Total length in mm

Countersink dia. in mm

Art. No.Pack Qty.

4 78 13 0650 700 400 16 96 13 0650 700 600 1

For timber. Excellent for countersinking in decking construction. With 1/4" E-type bit mount.

Thanks to the depth stop with a lockable countersink depth, you can achieve a visually consistent screw connection appearance.

Applications:Tropical woods, such as bangkirai, hard woods, soft woods, wood fiberboard and plastic-coated wood fiberboard.

Note: Not to be used with impacting driver.

Quadro Longlife Hammer Drill - Suitable for SDS-PLUS

Cat. Page 02 1121

Cat. Page 02 0691

Replacement Drill BitsDia. in mm Art. No. Pack Qty.4 0650 700 401 16 0650 700 601 1

The perfect solution when faced with reinforcements and hard materials with optimised, symmetrical, one-piece head with up to four cutting edges and Vario spiral conveyor.

Significantly improved compatibility with reinforcements.The symmetrical 4 x 90° cutting edge geometry (up to Ø 10 mm with solid carbide head) prevents the drill bit from hooking in or running off centre when striking reinforcements or hard pebbles in concrete.

Noticeably quicker drilling.The advanced tip geometry and asymmetrically placed elevations on the cutting edges ensure improved traction.

Perfect drilling properties over the entire service life.• Thanks to head geometry that is tailored to the drill bit

diameter.• Ø 4–16 mm: One-piece carbide element for high stability

thanks to the maximised attachment surface with the steel body.

• Ø 18–32 mm: Multi-piece carbide element for faster drilling progress and improved buffering of the torsional forces thanks to the trisection.

• Considerably improved drilling speed and dust removal while at the same time offering increased protection against breakage.

• Optimum guidance in drilled hole.• Precise spot drilling.

1 piece each dia. 5x110/50, 6x110/50, 8x110/50, 6x160/100, 8x160/100, 10x165/100 and 12x160/100 = 7 pieces Art. No. 0648 050 001

NoteSteel reinforcements may only be drilled through with permission from a structural engineer. With long drill bit lengths, pre-drill using a short drill bit of the same diameter.

19WURTH AUSTRALIA PTY. LTD.

Decking Construction Clamp & Decking Spacer

The perfect companion for any decking application.

• Designed for versatility across several applications.• Ideal for clamping either wood or metal.• The custom design and easy-to-use trigger mechanism allows the user

to quickly and effectively apply the maximum clamping force where it is required.

• Clamping width max 450 mm.

Includes: 1 decking construction clamp (incl. decking clamping jaws).2 universal clamping jaws – for use as a versatile single-handed clamp.

Together with the decking construction clamp, these spacers are the ideal tool combination for the easy and precise alignment and assembly of decking boards.

Cat. Page 12 3031

Description Art. No. P. Qty.Decking Construction Clamp 0714 662 451 1Decking Spacer 0907 000 101 10

Replacement Clamping Jaws

Art. No. 0714 662 452Pack Qty: 2

PUB04. Photographs are for illustrative purposes only and may not represent actual products. We reserve the right to correct printing errors. Wurth is a registered trademark of Wurth International AG. ABN 48 002 487 096. All information, images and content is copyright of Wurth Australia Pty. Ltd.

Wurth Australia Pty. Ltd. Head Office2/1 Healey Road, Dandenong South, VIC. 3175 T: 1300 65 77 65 (Local Call) F: 1800 03 23 96Info@wurth.com.au www.wurth.com.au