Avtron IR Bullet Camera AA-4544-6044P-FSR2-manual

8/22/2019 Avtron IR Bullet Camera AA-4544-6044P-FSR2-manual

1/16

Model : AA-4544P-FSR2Model : AA-6044P-FSR2


2/16

CAUTION : TO REDUCE THE RISK OF

ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS

INSIDE REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

02

This lighting flash with arrowhead symbol within an equilateral triangle isintended to alert the user to the presence of uninsulated dangerous voltage withinthe products enclosure that may be of sufficient magnitude to constitute a riskof electric shock to persons.

The exclamation point within an equilateral triangle is intend to alert the user tothe presence of important operating and maintenance instruction in the literatureaccompanying the product.

FCC WARNING : This equipment may generate or use radio frequency energy. Changesor modifications to this equipment may cause harmful interference unless the

modifications are expressly approved in the user manual. The user could lose the authorityto operate this equipment if an unauthorized change or modification is made

This equipment has been tested and found to comply with the limits for a class A digitaldevice, pursuant to part 15 of the FCC Rules. These limits are designed to providereasonable protection against harmful interference when the equipment is operated in acommercial environment

CAUTIONRISK OF ELECTRIC SHOCK

DO NOT OPEN


3/16

03

This equipment generates, uses, and can radiate radio frequency energy and, if notinstalled and use in accordance with the instruction manual, may cause harmfulinterference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in

which cause the user will be required to correct the interference at his own expenses.

A suitable conduit entries, knock-outs or glands shall be provided in the cable entries of thisproduct in the end user.

Caution:Danger of explosion if battery is incorrectly replaced. Replaced only with thesame or equivalent type recommended by the manufacturer. Dispose of used batteries

according to the manufacturers instructions.

Holes in meta, through which insulated wires pass, shall have smooth well roundedsurfaces or shall be provided with brushing.

WARNING:Do not install this equipment in a confined space such as a bookcase orsimilar unit.

WARNING: Wiring methods shall be in accordance with the National Electric Code,ANSI/NFPA 70.

WARNING:This is a class A product. In a domestic environment this product may causeradio interference in which case the user may be required to take adequate measures.

WARNING:To reduce a risk of fire or electric shock, do not expose this product to rain ormoisture.

Caution:This installation should be made by a qualified service person and should confirmto all local codes.

Caution:To avoid electrical shock, do not open the cabinet. Refer servicing to qualifiedpersonnel only.


4/16

To disconnect power from the mains, pull out the mains cord plug.When install the product, ensure that the plug is easily accessible.

04

Caution: The apparatus should not be exposed to water and no objects filled with liquids, such asvases, should be placed on the apparatus.

Disposal of your old appliance

1. When this crossed-out wheeled bin symbol is attached to a product it means theproduct is covered by the European Directive 2002/96/EC

2. All electrical and electronic products should be disposed of separately from themunicipal waste stream via designated collection facilities appointed by thegovernment or the local authorities.

3. The correct disposal of your old appliance will help prevent potential negative

consequences for the environment and human health.

4. For more detailed information about disposal of your old appliance, please contactyour city office, waste disposal service or the shop where you purchased theproduct.


5/16

Important Safety Instructions

1. Read this instructions.-All these safety and user instructions should be read before the productis operated.

2. Keep these instructions:- The safety, operating and user instructions should be retained forfuture references.

3. Heed all warnings :- All warnings on the product and in the operating instructions should beadhered to.

4. Follow all instructions:- All operating and user instructions should be followed.

5. Do not use this apparatus near water :- e.g near swimming pool ,Bathroom, wet walls.

6. Clean Only with dry cloth:- Unplug the power supply and then clean with dry cloth.

7. Do not block any ventilation openings, install in accordance with the mfg instructions:- Kindlyprovide some air ventilation in any form. The opening should never be blocked by placing theproduct on a bed, sofa, fug or other similar surface.

8. Do not install near any heat sources such as radiators, heat registers, stoves or otherapparatus that produce heat.

9. Protect the power cord from being walked on or pinched particularly at plugs, conveniencereceptacles, and the pint where they exit from the apparatus.

10.Only use attachments/accessories specified by the manufacturer.

11. Use only with the cart, stand, tripod, bracket, or table specified by themanufacturer, or sold with the apparatus. When a cart is used use cautionwhen moving the cart/apparatus combination to avoid injury from tip over.

12.Unplug this apparatus during lighting storms or when unused for long periodsof time.

13.Refer all servicing to qualified service personal. Servicing is required when the apparatus hasbeen damaged in any way, such as power supply cord or plug is damaged.

05


6/16

Safety Precautions

Do not attempt to disassemble the camera.

To Prevent electric shock, do not remove screws or covers. There are no user serviceable parts

inside. Ask a qualified service personnel for servicing.

Do not use strong solvents or detergents.

Use a dry cloth to the camera when it is dirty. If it is hard to remove the dirt on the camera, Use amild detergent and wipe it gently.

Before operating, please check proper temperature, humidity and power sourceratings.

Use the camera under conditions where temperature is between -10C ~+50C.

Do not expose the camera in such conditions as shown below.

User in a room or area filled with cigarettes smoke, dust or gas.

Avoid the camera with direct sunlight

Do not aim the camera at bright objects. Never face it with direct sunlight or other extremelybright objects.

Otherwise blooming or smear may be caused.

Handle the camera with care

Do not abuse the camera .Avoid striking, shaking, etc. The camera could be damaged byimproper handling or storage.

Do not expose the camera to rain or moisture

This product is designed for indoor use or location where it is protected from rain and moisture.

06


7/16

Contents

Cautions for Safe Operation ........................................................ 07

Box contains ............................................................................... 08

Construction ............................................................................... 09

Installation .................................................................................. 11

Troubleshooting .......................................................................... 13

Specification ............................................................................... 14

07


8/16

Cautions for Safe Operation

Power Supply

This camera must always be operated a DC 12V only.

Handling of the unit

Be careful not to spill water or other liquids on the unit. Be cautions not toget combustible or metallic material inside the body. If used with foreign

Matter inside, the camera is liable to fail or to get a cause of fire or electricshock.

Operating and storage location

Avoid viewing a very bright object during an extended period. Avoidoperating or storing the unit in the following locations.

Extremely hot or cold places( -10C ~+50C We recommended to use unitin between 0C ~+45C)

Damp or dust place

Places exposed to rain

Places subject to strong vibration

Close to generators of powerful electromagnetic radiation such as radioor TV transmitters.

08


9/16

Box contains

1

2

Camera

Cable

DC Power Plug

Video BNC Plug

Screws3

09


10/16

Construction

Camera Body

Sun Shield

Lens

Front View

IRIR Sensor

10


11/16

Construction

11

Sun ShieldUp & Down

Control Screw

Left & Right

Control

Side View


12/16

Installation

1) Locate Installation Area. Select areawhere it would hold the camera forlong time.

2) 3-Axis Bracket on the wall or ceilingwith "L" Wrench and screw given and

select the area you would like tomonitor.

3) Adjust Sunshield Top Cover to protectagainst directly sunlight.

4) Connect Power DC12V and Video Or

in to Video Input of DVR.

5) Using a screw driver open or changethe camera Mounting & Bracket forsuitable Position.

6) Always install the camera on RightPosition with Wall or Ceiling Mount.

Power

Video

12

Sunshield


13/16

Installation

13

Cable

Video

Power


14/16

Troubleshooting

If you are not able to view anything from the screen

- Check power, video, strength of signal. Check monitor input/output. Check camera connectionnumber with monitor.

For Fuzzy Screen.

- Check camera lens for dust or dirt. If so wipe them off with dry towel or brush.- Check cover to see if it's clean. If so wipe them off with dry towel or brush.

- Check for direct sunlight exposure towards camera.- Check and see if protection film from camera cover is removed.- Check for camera focus.

For Dark Screen

- Check for Monitor Brightness. Unbalanced Black & White on the Monitor.

- Check Monitor -Adjust the cameras position or angle of lens.

When screen is not clear with IR LED functioning

- Check glass cover for dust : If there is dust clean them with dry towel or brush

If problem still remains please contact our Technical Support Department.

14


15/16

Specification

15

Model

Image Sensor Sony 1/3 Super HAD CCD II 1/3 Prop. Image Sensor

Picture elements(Effective Pixels) PAL -500(H) * 582(V) PAL -752(H) * 582(V)NTSC - 510(H) * 494(V) NTSC - 768(H) * 494(V)

Scanning System 2:1 Interlace

Scanning Frequency PAL H: 15.625 KHz V:50HzNTSC H:15.734Khz V:60Hz

Horizontal Resolution 450 TVL 600 TVL

S/N Ratio >48 db >65 db

Shutter Speed 1/50(60) -1/20000s 1/50(60) -1/1000000s

Back Light Compensation(BLC) Auto

Auto Gain Control (AGC) Auto

White Balance ATW

Min. Illumination 0.01Lux @ Day 0.05Lux @ Day0 Lux @Night with IR Led ON 0 Lux @Night with IR Led

ON, IR Cut Filter

IR LED 24 Pcs

IR Effect Distance 22 Mtr approx

Focal Length 3.6 mm IR Enable Lens

AA-4544P-FSR2 AA-6044P-FSR2


16/16

Specification

16 www.avtrontech.com

Aperture f/1.2Input voltage 12 V DC 10%

Video Output Level 1V p-p,75BNC connectors

Power Consumption

Documents

Avtron IR Bullet Camera AA-4544-6044P-FSR2-manual