Avaya ERS 3500 quick setup guide for IP Office Terminal emulation settings Property Value Baud Rate 9600 bps Data Bits 8 Stop Bits 1 Parity None Flow Control None Introduction This guide provides instructions for quick installation of an Avaya Ethernet Routing Switch (ERS) 3500 series switch with an Avaya IP Office 500 system. The ERS 3500 (from release v5.0.1) supports a CLI command that provides fast setup of a 3500 series PoE switch to best practices configuration in a Unified Communications solution incorporating Avaya IP Office and Avaya IP Phones on an ERS 3500 switch. The ERS 3500 supports a fully automated or user prompted command script. Step 1. Prepare hardware Unpack IP Office hardware and setup Unpack Avaya Ethernet Routing Switch using IP office installation guides. 3500 series PoE switch. Step 2. Connect PC to Console port on the Switch Connect PC with serial cable to switch RJ-45 console port using Windows Hyperterm or other terminal emulator. Set the terminal protocol on the terminal or terminal emulation program to VT100 & VT100/ANSI. (Use DB9 Female to RJ-45 integrated console cable: AL2011022-E6 or Avaya RED DB9 Female to RJ-45 adaptor: AL2011020-E6 with Cat5E straight cable to RJ-45 console port.) NOTE: RJ-45 Console ports on Avaya switches have a BLUE line aound the port. Step 3. Configure Ethernet Switch parameters Use the CLI command run ipoffice fully automated script if Avaya IP Office is being installed with system default settings. Use the CLI command user input prompted script if Avaya IP Office is being installed with customized (non-default) configuration. The ERS 3500 run ipoffice verbose script will allow configuration settings to be customized to integrate with IP Office settings. At AVAYA banner, press CTRL+Y then type enable at the “35xx-PWR+>” prompt. At “35xx-PWR+#” prompt, type the required CLI command: • run ipoffice (Fully automated setup script) • run ipoffice verbose (User prompted setup script) (These commands will configure the switch to optimally run with Avaya IP Office) Step 4. Automated script settings for Avaya Ethernet Routing Switch • Voice VLAN ID = 42 • Voice VLAN 42 gateway IP = 192.168.42.254 • Data VLAN ID = 44 • Data VLAN 44 gateway IP = 192.168.44.254 • Switch Management IP = 192.168.44.254 • Default route 0.0.0.0 to 192.168.44.2 Step 5. Connect Avaya IP Office, Avaya IP Phones & other devices Following the port assignments indicated, use the illustration below to connect your Avaya IP Office, WAN Router, IP Phones and devices to the Avaya Ethernet Routing Switch. RJ-45 Jack Name Requirement RJ-45 8-Pin Female Jack 1 RTS (Ready To Send) Optional - can swap or link with pin 8 optional 2 DTR (Data Terminal Ready) Optional 3 TXD (Transmit Data) Mandatory 4 DCD (Carrier Detect) Optional 5 GND (Ground) Mandatory 6 RXD (Receive Data) Mandatory 7 DSR (Data Set Ready) Optional 8 CTS (Clear To Send) Optional - can swap or link with pin 1 • IP Office Call server address = 192.168.42.1 • IP Office File server address = 192.168.42.1 • Switch port 1 – IP Office • Switch port 2 – WAN / ADSL Router • Switch port 3 & above – IP Phones, PCs, printers and other data devices.
Avaya ERS 3500 quick setup guide for IP Office; ERS version 5.0.1 available. incorporates easy setup script for ERS 3500 in Avaya IP Office environments!!!
Citation preview
1. Avaya ERS 3500 quick setupguide for IP
OfficeIntroductionStep 3. Configure Ethernet Switch parametersThis
guide provides instructions for quick installation of an Avaya
Ethernet Routing Switch Use the CLI command run ipoffice fully
automated script if Avaya IP Office is being installed(ERS) 3500
series switch with an Avaya IP Office 500 system. The ERS 3500
(from release with system default settings. Use the CLI command
user input prompted script if Avaya IPv5.0.1) supports a CLI
command that provides fast setup of a 3500 series PoE switch
toOffice is being installed with customized (non-default)
configuration. The ERS 3500 runbest practices configuration in a
Unified Communications solution incorporating Avaya IPipoffice
verbose script will allow configuration settings to be customized
to integrate withOffice and Avaya IP Phones on an ERS 3500 switch.
The ERS 3500 supports a fully IP Office settings.automated or user
prompted command script.At AVAYA banner, press CTRL+Y then type
enable at the 35xx-PWR+> prompt.At 35xx-PWR+# prompt, type the
required CLI command:Step 1. Prepare hardware run ipoffice (Fully
automated setup script) run ipoffice verbose (User prompted setup
script)Unpack IP Office hardware and setup Unpack Avaya Ethernet
Routing Switch (These commands will configure the switch to
optimally run with Avaya IP Office) using IP office installation
guides.3500 series PoE switch.Step 4. Automated script settings for
Avaya Ethernet Routing Switch Voice VLAN ID = 42 IP Office Call
server address = 192.168.42.1 Voice VLAN 42 gateway IP =
192.168.42.254 IP Office File server address = 192.168.42.1 Data
VLAN ID = 44 Switch port 1 IP Office Data VLAN 44 gateway IP =
192.168.44.254 Switch port 2 WAN / ADSL Router Switch Management IP
= 192.168.44.254 Switch port 3 & above IP Phones, PCs, Default
route 0.0.0.0 to 192.168.44.2 printers and other data devices.Step
2. Connect PC to Console port on the SwitchConnect PC with serial
cable to switch RJ-45 console port using Windows Hyperterm orStep
5. Connect Avaya IP Office, Avaya IP Phones & other
devicesother terminal emulator. Set the terminal protocol on the
terminal or terminal emulationprogram to VT100 &
VT100/ANSI.Following the port assignments indicated, use the
illustration below to connect your Avaya(Use DB9 Female to RJ-45
integrated console cable: AL2011022-E6 or Avaya RED DB9 Female to
RJ-45IP Office, WAN Router, IP Phones and devices to the Avaya
Ethernet Routing Switch.adaptor: AL2011020-E6 with Cat5E straight
cable to RJ-45 console port.)Terminal emulation settings Property
ValueRJ-45 NameRequirementJackBaud Rate 9600 bps1 RTS (Ready To
Send) Optional - can swapData Bits8or link with pin 8RJ-45
8-PinoptionalFemale JackStop Bits1 2DTR (Data Terminal Ready)
OptionalParity None 3TXD (Transmit Data) Mandatory Flow ControlNone
4DCD (Carrier Detect)Optional 5GND (Ground)Mandatory 6RXD (Receive
Data)Mandatory 7DSR (Data Set Ready)Optional 8CTS (Clear To Send)
Optional - can swapor link with pin 1NOTE: RJ-45 Console ports on
Avaya switches have a BLUE line aound the port.
2. Avaya ERS 3500 and IP Office solution reference diagramsAvaya
IP Office 500 + ERS 3500 for 2-22 usersAvaya IP Office 500 + ERS
3500 for 2-22 users Physical solution reference architecture
Logical solution reference architectureAvaya IP Office 500(standard
or premier version) Voice VLAN (VLAN 42)WAN port LAN port
(rear)(Not connected) (to ERS 3500 Port 1)Avaya IP Office 500
Supported on: Avaya ERS 3500 ERS 3526T-PWR+ (PoE Switch)ERS
3510GT-PWR+ ERS 3524GT-PWR+Avaya 16xx/96xx IP Phones (PoE) WAN
Router or ADSL ModemWAN /Office Avaya ERS 3500 server WAN /(PoE
Switch) Internet Internet Data VLAN (VLAN 44) Office Avaya IP
Phones (PoE) printerWAN Router or Wired & Wireless Devices
Office ADSL ModemOffice serverLaptop/desktopPCs(DHCP Server)
(connected to IP Phone data port) Wireless AP(802.11b/g/n)