AtlonA8X82 HDMI with IR Matrix Switcher

over CAT5AT-PROHD88M-SR

User Manual

AT-PROHD88M-SFRONT VIEW

AT-PROHD88M-RFRONT VIEW

AT-PROHD88M-SREAR VIEW

AT-PROHD88M-RREAR VIEW

TABLE OF CONTENTS

1. Introduction .................................................. 1

2. Features .................................................. 1

3. Specification .................................................. 2

4. Package Contents .................................................. 2

5. Panel Descriptions .................................................. 3

5.1. Front Panel .................................................. 3

5.2. Rear Panel .................................................. 3

6. Connection and Operation .................................................. 5

6.1. Operation on front panel .................................................. 5

6.2. Control via RS232 .................................................. 6

6.2.1. The Interface of AT-PROHD88M-SR .................................................. 6

6.2.2. The Message Window .................................................. 7

6.2.3. The Com Status ................................................. 8

6.2.4. Control Command Format .................................................. 9

6.2.5. Control Code .................................................. 9

6.2.6. Read Status Command .................................................. 10

6.2.7. Web Password Reset .................................................. 10

6.2.8. AT-PROHD88M-SR RS-232 Remote

Control Protocol .................................................. 11

6.3. LAN Control .................................................. 14

7. IR Call-back from Remote Locations to Control the AT-PROHD88M-SR .................................................. 16

8. Instruction of TX IR .................................................. 16

9. IR Cqdes .................................................. 17

10. Details on the EDID .................................................. 18

11. Maintenance .................................................. 20

12. Product Service .................................................. 20

13. Connection Diagram .................................................. 21

14. Safety Information .................................................. 22

15. Warranty .................................................. 23

16. Atlona Product Registration .................................................. 24

INTRODUCTION

1

Atlona’s AT-PROHD88M-SR is a true 8x8 HDMI matrix switcher. This unit allows any of the eight HD source’s (i.e. Blue-Ray player, HD DVD player, satellite receiver, PS3, AppleTV etc.) to be routed to any of the eight HD displays simultaneously. Users can choose several differ-ent ways of controlling the matrix: IR Back Channel, RS232, RS485, LAN and supplied remote control. The Atlona AT-PROHD88M-SR comes with 8 x IR emitters for controlling sources next to the switch as well as 1 x IR emitter for each one of the Twisted Pair Receiver units for con-trolling sources from other locations.

The AT-PROHD88M-SR has the ability of equalization, amplification and re-clocking the sig-nal to ensure HDMI accurate signal transmission through long cables without quality loss. The transmission distance of Twister Pair (Cat5/6) outputs can reach up to 100ft @ 1080P with infrared control signal. Distance can be extended for additional 165ft with an optional Atlona repeater unit AT-PROHD-RP. It is recommended to use CAT6 (568B terminated) wire to get the longer distance.

The AT-PROHD88M-SR offers the perfect solutions for any digital entertainment center, digital media show sites, retail show-rooms, Trade-Shows, High-End residential or commercial in-stalls, education and medical environments or any other.

• Allows up to eight HDMI devices to be independently switched to eight HDMI displays.

• High-resolutions support up to 1920x1200 or 1080p

• HDCP compliant.

• HDMI version 1.3.

• DVI Compatible

• Switcher outputs signal on both Twister Pair lines and direct HDMI output simultaneously, therefore two displays could be active at the same time out of one output.

• The eight outputs are capable of displaying the same or different sources simultaneously. Each output includes one HDMI A type connecter and a set of dual RJ-45 connecters as the second mirrored HDMI output. The two outputs work simultaneously.

• EDID Memory function, which already includes most common displays EDID information

• Discrete IR back channel.

• Six switching modes: panel buttons, local IR, IR call back from remote locations, RS232, RS485 and Ethernet.

• Eight IR emitters to control the HDMI sources.

FEATURES:

SPECIFICATIONS

Operating Temperature Range -5 to +35°C (-41 to +95 °F)Operating Humidity Range 5 to 90 % RH (no condensation)Input Video Signal 0.5-1.0 volts p-pInput DDC Signal 5 volts p-p (TTL)Format Supported DTV/HDTV:1080P/1080i/720P/576P/480P/576i/480i

PC: VGA, SVGA, XGA, SXGA, UXGA, WXGA, WSXGA, WUXGA

Audio Format Supported DTS-HD, Dolby tureHD, 7.1ch and othersHDMI Standard HDMI 1.3 (compatible with previous versions)Maximum Transmission Distance <50ft on the direct HDMI outputUTP cable Transmission Distance <130ft with Twister Pair Receivers, if longer distance is

required, we offer optional UTP RepeatersIR wave-length & frequency Wave-length: 940nm IR frequency: 38KHZPower Consumption 35wtts (Max)Dimensions (Inch) 17.3L×7.9W×1.7HWeight (Main Unit) 7.6 LB

Note: Specifications are subject to change without notice.

Master Unit

1. 1 x AT-PROHD88M-SR

2. 8 x IR emitter cables (marked IR TX),

3. 1x IR receiver cables (marked IR RX)

4. 1 x USB to RS232 cable

5. 1 x 12VDC Universal Power Supply. (UL Listed)

6. 1 x Rack Mounting ears.

7. 1 x IR Remote.

Slave Unit

1. 8 x Receiver Units AT-PROHD88M-R

2. 8 x IR receiver cables (marked IR RX),

3. 8X 5VDC power supply,

4. 8x Rack Mounting ears.

1. 1 x Operating Instructions.

2. 1 x CD with RS232 commands and control software.

2

PACKAGE CONTENTS

2

AT-PROHD88M-SFront Panel

1. Power switch.

2. Output selection push-buttons (Use it to choose the preferred output channel).

3. LED indicator of input for output port 1 to 8.

4. Action Confirmation Button (Push the ‘Enter’ button to confirm the changing of input channel to the output).

5. Input selection knob. (Turn to select the proper input to the output)

6. IR window.

Rear Panel

1. IR extension. 7. Input ports 1 to 4.

2. RS485 port. 8. Power input.

3. LAN port. 9. Output 5 and 8 with HDMI and CAT5E.

4. IR emitter, corresponding to the Input port from 1 to 8 10. Input ports 5 to 8.

5. RS232 port. 11. DIP switch setting.

6. Output 1 to 4 with HDMI and CAT5E.

Note: The RS232 port and LAN port are for matrix control. The LAN port is connected to the computer via cross UTP (568A+568B) and connected to the router or switcher via direct UTP.

3

PANEL DESCRIPTIONS

1 2 3 4 5 6 7 8 109

AT-PROHD-RP

1. HDMI output.

2. CAT-5e/6 input1 and input2.

3. Power input, 5VDC. (power supply is not required if used within suggested distance)

4. IR Receiver INPUT

Note: IR emitter should be placed as near to the IR eye as possible.

4

43

1 2

5

1. Connect the HDMI input sources (such as HD-DVD, PS3, STB, AppleTV etc) into the AT-PROHD88M-SR.

2. Connect the standard HDMI outputs (such as LCD or DLP) into AT-PROHD88M-SR.

3. Connect two CAT-5E or CAT-6 cables to both Twisted Pair outputs of the unit and receiver Twister Pair inputs. Please pay attention to the sequence of the two cables, CAT5/6-1->CAT5/6-1, CAT5/6-2->CAT5/6-2. (The cable termination must follow the standard of EIA/TIA 568B for the longest distance;

4. Connect the HDMI output (such as: LCD or DLP) into the Twister Pair inputs on the receiver.

5. Connect the IR receiving cable into HDMI receiver IR RX and connect the IR TX cable into the main switcher IR emitter.

6. Power on the input source you want to view. (Keep the unused input powered off, otherwise it may interfere.)

7. Connect the power supply into AT-PROHD88M-SR

8. Turn on the power. When the LED panel stops flashing, the initialization of the unit is ready.

9. Turn on the displays you want to watch.

10. Use the remote supplied or manually push the button on the front panel to choose input source. Also use infrared extension receiver, RS232, RS485 or LAN port to do the control.

6.1. Operation on front panel.1. Press the output select button for the output channel which you want to change. Corresponding LED of the

output channel will blink slowly.

2. Rotate the input Knob to choose the desired input channel.

CONNECTION and OPERATION

the LED Flash

press the output select push button

Rotate the input select knob to choose the desired input channel

4

6

3. Press the ‘Enter’ button to confirm the action. LED will stops blinking.

6.2. Control via RS232 6.2.1. The Interface of AT-PROHD88M-SR

the LED stops flashing

press the enter push button to confirm the action

6 7

6.2.2. The Message Window

Receive WindowThe “receive window” will show the message received from Switcher. When you click the Control Buttons (see step 4) or send Control Command (see 2.3) to the matrix switch, it will send out the message about “operation results” such as below

Status ButtonClick this button to read the status of AT-PROHD88M-SR. The status is about which input is selected by the output.

Send WindowInput the control command in this window. The control command use ASCII.

8

Mode button Click this button to set the switch mode: Quick switch or Normal switch. When you click this button it will read the current mode of AT-PROHD88M-SR; if you want to change the mode, select the mode you want and click OK.

Set IP button Click this button to set IP address for NETCTL.

6.2.3. The Com Status

Connect state Connect state shows whether the com is open or not. If it is open, the state is green. Otherwise, the state is red.

Com select Select which com you will use.

Connect button The word on this button will change when the connection state changes. If the word is “Disconnect”, then click this button; the com will be closed. If the word is “Connect”, then click this button; the com will be opened.

8

6.2.4. Control command formatIf users want to write their own control software, below are data formats and baud rate set-tings. Com port setting:Baud Rate: 9600 bpsData bits: 8 bitsParity: NoneStop bits: 1 bitFlow control: None

The command format is as follow:

cir + ‘_’ + code + ‘ ’

“cir” is the key word, ‘_’ is Space, “Code” is the Control code , ‘ ’ is carriage return.

for example: “ cir 39 ”(hex: 63 69 72 20 33 39 0D 0A), when the unit receives this command ,it will change the Outport4 status to the next input port. ( “c”-0x63, ”I”-0x69, ”r”-0x72, ” “-0x20, ”3”-0x33, ”9”-0x39, ‘ ’-0x0d0a)

6.2.5. Control codeAT-PROHD88M-SR:

Ouput1 <“08” >“09”1“00” 2“01” 3“02” 4“03” 5“04” 6“05” 7“06” 8“07”

Ouput2 <“18” >“19”1“10” 2“11” 3“12” 4“13” 5“14” 6“15” 7“16” 8“17”

Ouput3 <“28” >“29”1“20” 2“21” 3“22” 4“23” 5“24” 6“25” 7“26” 8“27”

Ouput4 <“38” >“39”1“30” 2“31” 3“32” 4“33” 5“34” 6“35” 7“36” 8“37”

Ouput5 <“48” >“49”1“40” 2“41” 3“42” 4“43” 5“44” 6“45” 7“46” 8“47”

Ouput6 <“58” >“59”1“50” 2“51” 3“52” 4“53” 5“54” 6“55” 7“56” 8“57”

Ouput7 <“68” >“69”1“60” 2“61” 3“62” 4“63” 5“64” 6“65” 7“66” 8“67”

Ouput8 <“78” >“79”1“70” 2“71” 3“72” 4“73” 5“74” 6“75” 7“76” 8“77”

9

10

When you succeed in sending a control command to this unit, it will feedback current output port status to show which input port is selected. The return status format is as follows:

“s” Output port Input port

1st byte 2nd byte 3rd byte

For example, if you send “cir 44 ” to Switcher if succeeds, it will feedback “s55”, meaning OutPut5 selects InPut5.

6.2.6. Read Status CommandThe command length is 4 bytes.

bc + ‘_’ + ‘ ’

“bc” is the key word, ‘_’ is Space, ‘ ’ is carriage return.

When you succeed in sending the read status command to the AT-PROHD88M-SR, it will feed-back the status of all outputs. When you send “Bc” to unit, it will feedback the current status of the switcher. The feedback status format is as below,

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16‘\r’ ‘\n’ s X1 X2 s X3 X4 s X5 X6 s X7 X8 ‘\r’ ‘\n’

The status has 16 bytes. X1,X2.X3,X4,X5,X6,X7,X8 separately stands for the related input chosen by the output. X1 stands for the output 1, X2 stands for the output 2 and so on. For example, if the status is “\r\ns12s22s53s45\r\n”, it means that the output 1 select the input 1, the output 2 selects the input 2, output 3 selects the input 2, output 4 selects the input 2, output 5 selects input 5, the output 6 selects the input 3, the output 7 selects the input 4, the output 8 selects the input 5.

6.2.7. Web password resetThe command length is 4 bytes.

rpw+ ‘ ’

“rpw” is the key word , ‘ ’ is carriage return.

When you send the Web password reset command to the unit, it will feedback “rpw”, and the web password will be set as “0000000000”.

10

6.2.8. AT-PROHD88M-SR RS-232 Remote Control ProtocolThe connection between AT-PROHD88M-SR and remote controller with RS-232 modem cable

AT-PROHD88M-SR Remote ControllerPIN Definition PIN Definition1 NC 1 NC2 Tx 2 Rx

3 Rx 3 Tx4 NC 4 NC5 GND 5 GND6 NC 6 NC7 NC 7 NC8 NC 8 NC9 NC 9 NC

RS-232 transmission format: Baud Rate : 9600 bps Data Bit : 8 bits Parity : None Stop Bit : 1 bit

Command:

OUTPUT COMMAND ACTION

Output 1cir 00 Output 1 select Input1cir 01 Output 1 select Input2cir 02 Output 1 select Input3cir 03 Output 1 select Input4cir 04 Output 1 select Input5cir 05 Output 1 select Input6cir 06 Output 1 select Input7cir 07 Output 1 select Input8

< cir 08 Output 1 select Input previous> cir 09 Output 1 select Input next

Output 2cir 10 Output 2 select Input1cir 11 Output 2 select Input2cir 12 Output 2 select Input3cir 13 Output 2 select Input4cir 14 Output 2 select Input5cir 15 Output 2 select Input6cir 16 Output 2 select Input7cir 17 Output 2 select Input8

< cir 18 Output 2 select Input previous> cir 19 Output 2 select Input next

11

12

Output 3cir 20 Output 3 select Input1cir 21 Output 3 select Input2cir 22 Output 3 select Input3cir 23 Output 3 select Input4cir 24 Output 3 select Input5cir 25 Output 3 select Input6cir 26 Output 3 select Input7cir 27 Output 3 select Input8

< cir 28 Output 3 select Input previous> cir 29 Output 3 select Input next

Output 4cir 30 Output 4 select Input1cir 31 Output 4 select Input2cir 32 Output 4 select Input3cir 33 Output 4 select Input4cir 34 Output 4 select Input5cir 35 Output 4 select Input6cir 36 Output 4 select Input7cir 37 Output 4 select Input8

< cir 38 Output 4 select Input previous> cir 39 Output 4 select Input nex

Output 5cir 40 Output 5 select Input1cir 41 Output 5 select Input2cir 42 Output 5 select Input3cir 43 Output 5 select Input4cir 44 Output 5 select Input5cir 45 Output 5 select Input6cir 46 Output 5 select Input7cir 47 Output 5 select Input8

< cir 48 Output 5 select Input previous> cir 49 Output 5 select Input nex

Output 6cir 50 Output 6 select Input1cir 51 Output 6 select Input2cir 52 Output 6 select Input3cir 53 Output 6 select Input4cir 54 Output 6 select Input5cir 55 Output 6 select Input6cir 56 Output 6 select Input7cir 57 Output 6 select Input8

< cir 58 Output 6 select Input previous> cir 59 Output 6 select Input nex

Output 7cir 60 Output 7 select Input1cir 61 Output 7 select Input2cir 62 Output 7 select Input3

12

Output 7cir 63 Output 7 select Input4cir 64 Output 7 select Input5cir 65 Output 7 select Input6cir 66 Output 7 select Input7cir 67 Output 7 select Input8

< cir 68 Output 7 select Input previous> cir 69 Output 7 select Input next

Output 8cir 70 Output 8 select Input1cir 71 Output 8 select Input2cir 72 Output 8 select Input3cir 73 Output 8 select Input4cir 74 Output 8 select Input5cir 75 Output 8 select Input6cir 76 Output 8 select Input7cir 77 Output 8 select Input8

< cir 78 Output 8 select Input previous> cir 79 Output 8 select Input next

13

6.3. LAN controlNote:Use the direct UTP cable to connect with PC, or use cross cable to connect to the Ethernet switcher

1) When NETCTL runs on PC for the first time, it will create a file ‘NETCTL.TXT’. This file is for device’s information backup. This information includes MAC address of unit, IP address, device name etc.

Double click NETCTL.exe to run NETCTL. It will search for the device. If the device is a new one, NETCTL will list it‘s IP address. If IP address appears,please click the button

NETCTL will change the IP address to device’s name

If you want to change the device name, Right-click the device name. A pull down menu will be displayed. Click the item ‘Rename’ to rename.

2) Double click the device name, or click right button and click ‘open’. A web browser will be shown. The default password is “0000000000”; input the password and login. The device controller page will be displayed.

14

14

The right area is for device controlling. Click these buttons to control the device. It is the same as using the remote controller. The left area shows which inputs are being chosen by the outputs. 3) When ‘Assign IP’ is displayed, it means that the device has not been assigned an IP au-tomatically. Double click this item, or click right button and click ‘Assign IP’ on the pull down menu. You can assign the IP address in the Assign IP dialog.

Click OK after assigning the new IP and to return to the previous dialog.

Click and . The device can be displayed correctly. ATTENTION:Here, assign IP is different from Set-IP in COMCTL. Set-IP in COMCTL to save the IP address in flash. When the unit is powered on, it will read the IP from flash and set it as static IP. Assign IP the function when automatically obtained IP address fails. This assigned IP address is not saved in flash.

15

16

You can use the unit’s remote through the IR RX of the HDMI receiver to change the input channel for the UTP out of the switcher, just by changing this UTP output.

This function can be set on or off: press the output1 button and the output8 button at the same time for about 3 seconds. The LEDs will display ‘IR ON’ or ‘IR OFF’.

1. UTP receiver

2. IR RX

The sequence of “TX IR1, TX IR2, TX IR3, TX IR4, TX IR5, TX IR6, TX IR7, TX IR8” one-to-one corresponds with “HDMI INPUT1, HDMI INPUT2, HDMI INPUT3, HDMI INPUT4, HDMI INPUT5, HDMI INPUT6, HDMI INPUT7, HDMI INPUT8”. When an output chooses a certain input, the call-back IR signal of RJ45 on this output will choose the corresponding “TX IR” port to send the signal out. For example, OUTPUT1 chooses INPUT3, then the call-back IR signal of RJ45 on OUT-PUT1 will choose “TX IR3” to send the signal out.

1. UTP receiver

2. IR RX

3. IR TX

IR Call-back from Remote Locations to Control the AT-PROHD88M-SR

INSTRUCTION of TX IR

16

More advanced users can program the following codes into the IR control systems or universal/learning remote controls.

input 1 input 2 input 3 input 4 input 5 input 6 input 7 input 8output 1 80 81 82 83 84 85 86 87output 2 90 91 92 93 94 95 96 97output 3 A0 A1 A2 A3 A4 A5 A6 A7output 4 B0 B1 B2 B3 B4 B5 B6 B7output 5 C0 C1 C2 C3 C4 C5 C6 C7output 6 D0 D1 D2 D3 D4 D5 D6 D7output 7 E0 E1 E2 E3 E4 E5 E6 E7output 8 F0 F1 F2 F3 F4 F5 F6 F7

17

IR CODES

Position ID EDID Operational Mode1 2 3 40 1 0 0 Fully COPY (STANDARD MODE)0 1 1 0 limited TMDS CLK COPY EDID1 0 0 0 Fixed HMDI12_2CH EDID1 0 1 0 Fixed HMDI12_6CH EDID1 1 0 0 Fixed HMDI13_2CH EDID1 1 1 0 Fixed HMDI13_6CH EDID

Other conditions Limited TMDS CLK COPY EDIDLimited TMDS CLK COPY EDID - Copy the EDID from the sink device to the matrix. But will limit the bit-rate below 2.25GHz.

Fully COPY (STANDARD MODE) - Just copy the EDID from the sink device to the matrix. The matrix has some embedded EDID. We call them fixed EDID.

Fixed HMDI12_2CH EDID - Only support 2 channel audio. No deep-color support.

Fixed HMDI12_6CH EDID - Can support 6ch audio (for example DTS5.1, Dolby 5.1). No deep-color support.

Fixed HMDI13_2CH EDID - Only support 2 channel audio. Support deep-color video.

Fixed HMDI13_6CH EDID - Can support 6ch audio (for example DTS5.1, Dolby 5.1). Supports deep-color video.

Reading and saving EDID data from displayBefore reading and saving EDID data from display, please make sure which output the EDID is from and which input is the destination in which the EDID will be copied to. The detailed proce-dures are as below:

1. Choose the output where the EDID will be copied from (Assumed as OUTPUT_N), and input where the EDID will be copied to (Assumed as INPUT_N). Control the matrix to connect them.

2. Under AT-PROHD88M-SR’s normal working condition, push ‘ENTER’ and ‘OUTPUT_N’ simultaneously. Within two seconds the LEDs will light the character ‘-‘ circularly (This means the EDID COPY is auto running). Simply release the buttons and wait for the matrix to finish the operation.

3. If the EDID COPY succeeded, then the LED will show MIX OK. Otherwise the LEDs will dis-play MIX FL. Push the ‘ENTER’ button. Unit will go into normal working condition.

For example: Copy the EDID from the display connected to OUTPUT1 to INPUT8.

1. Connect the display to OUTPUT1 of the Switcher. Power-on the switcher and the display.

2. Switch the matrix to connect OUTPUT1 to INPUT8.

18

DETAILS ON THE EDID

18 19

3. Press down ‘ENTER’ and ‘OUTPUT_1’ simultaneously; after two seconds LED light show ‘-‘ circularly. (This means the matrix is performing EDID COPY). Release the buttons and wait for the machine to finish the remaining work.

4. If the EDID COPY succeeded, the LEDs will show ‘MIX OK’, otherwise the LEDs will display ‘MIX FL’. Then push the ‘ENTER’ button; the unit will go back to normal working condition.

Succeed, LED shows MIX OK

select input 8 channel for output 1

press output 1 button and enter button at the same time

20

Check the working status.Press “ENTER” button for 4 seconds, then the LED will show the working status one by one. For Example: switch mode---Debug mode---IR status---DIP setting status. Then push the ‘ENTER’ button or wait for 3 seconds, PRO-HD88M-SR goes back to normal working condition.

Switch mode: FAST SW fast swich mode/ NORM SW norm switch mode.

Debug mode: DBG OFF debug mode off / DBG ON debug mode on.

IR status: IR ON (the function of IR call back from remote locations to control the HDMI Matrix PROHD88M-SR is on/ IR OFF the function of IR call back from remote locations to control the HDMI Matrix PROHD88M-SR is off).

DIP setting status: FIX (fixed EDID)/ FULL CPY (full copy EDID) /LIM CPY (limited TMDS clock copy EDID); H12 2CH (HDMI 1.2 stereo)/ H12 6CH (HDMI 1.2 6channel)/ H13 2CH(HDMI 1.3 stereo) / H13 6CH(HDMI 1.3 6chan-nel)

Failed, LED shows MIX FL

Attention: 1. When the DIP switch is set to fixed EDID (1000---1111), the EDID COPY operation will fail. The LED will show MIX FD. 2. Please insert or extract cables gently.

Clean switcher with a soft, dry cloth. Never use alcohol, paint thinner or other chemicals to clean this unit.

Damage requiring service: The unit should be serviced by qualified Atlona service personnel if:

1. The DC power supply cord or AC adaptor has been damaged;

2. Liquids have been spilled into the switcher or HDMI receiver modules;

3. The unit does not operate normally (exceeds standard temperatures)

4. The unit has been dropped and the case has been damaged.

MAINTENANCE

PRODUCT SERVICE

CONNECTION DIAGRAM

21

DVD

STB

SOURCES 1 to 8

X-Box PS 3

LCD LCD

HDTV HDTV

AT-PROHD88M-R AT-PROHD88M-R

AT-PROHD-RP(optional accessory)

HDMI cable

HDMI cable HDMI cable

HDMI cable

2xCAT5e cable

2xCAT5e cable

20

SAFETY INFORMATION

22

Safeguards

To reduce the risk of electric shock, do notexpose this product to rain or moisture.

If the wall plug does not fit into your localpower socket, hire an electrician to replaceyour obsolete socket.

Do not modify the wall plug.Doing so will void the warranty and safetyfeatures.

This equipment should be installed nearthe socket outlet and the device shouldbe easily accessible in case it requiresdisconnection.

Precautions

FCC Regulations state that anyunauthorized changes or modifications tothis equipment not expressly approved bythe manufacturer could void theuser’s authority to operate thisequipment.

Operate this product using only theincluded external power supply. Use ofother power supplies could impairperformance, damage the product or causefires.

In the event of an electrostatic discharge,this device may automatically turn off. If thisoccurs, unplug the device, and plug it backin.

Protect and route power cords so they willnot be stepped on or pinched by anythingplaced on or against them. Be especiallycareful of plug-ins, or cord exit points fromthis product.

Avoid excessive humidity, suddentemperature changes or temperatureextremes.

Keep this product away from wet locationssuch as bathtubs, sinks, laundries, wetbasements and swimming pools.

Use only accessories recommended byATLONA to avoid fire, shock or otherhazards.

Unplug the product before cleaning. Usea damp cloth for cleaning. Do not usecleaning fluid or aerosols, which couldenter the unit and cause damage, fire orelectrical shock. Some substances mayalso mar the finish of the product.

Never open or remove unit panels or makeany adjustments not described in thismanual. Attempting to do so could exposeyou to dangerous electrical shock or otherhazards. It may also cause damage to yourAT-PROHD88M-SR. Opening the product will void the warranty.

Do not attempt to service the unit. Insteaddisconnect it and contact your AuthorizedATLONA reseller or contact ATLONAdirectly.

23

WARRANTY

1. LIMITED WARRANTY Atlona Technologies warrants that (a) its products (the “Product”) will perform substantially in accordance with the

accompanying written materials for a period of 3 YEARS from the date of receipt and (b) that the Product will be free from defects in materials and workmanship under normal use and service for a period of 3 years. In the event applicable law imposes any implied warranties, the implied warranty period is limited to 3 years from the date of receipt. Some jurisdictions do not allow such limitations on duration of an implied warranty, so the above limitation may not apply to Customer.

2. CUSTOMER REMEDIES Atlona Technologies and its suppliers’ entire liability and Customer’s exclusive remedy shall be, at Atlona Technolo-

gies’ option, either return of the price paid for the Product, or repair or replacement of the Product that does not meet this Limited Warranty and which is returned to Atlona Technologies with a copy of Customer’s receipt. This Limited Warranty is void if failure of the Product has resulted from accident, abuse, or misapplication. Any replacement Prod-uct will be warranted for the remainder of the original warranty period or 3 year, whichever is longer.

3. NO OTHER WARRANTIES TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, ATLONA TECHNOLOGIES AND ITS SUPPLI-

ERS DISCLAIM ALL OTHER WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH REGARD TO THE PRODUCT AND ANY RELATED WRITTEN MATERIALS. THIS LIMITED WARRANTY GIVES CUSTOMER SPECIFIC LEGAL RIGHTS. CUSTOMER MAY HAVE OTHER RIGHTS DEPENDING ON THE JU-RISDICTION.

4. NO LIABILITY FOR DAMAGES TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL ATLONA TECHNOLO-

GIES OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING WITHOUT LIMITA-TION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR INDIRECT DAMAGES FOR PERSONAL INJURY, LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE USE OF OR INABILITY TO USE THIS PRODUCT, EVEN IF ATLONA TECHNOLOGIES HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN ANY CASE, ATLONA TECHNOLOGIES’ AND ITS SUPPLIERS’ ENTIRE LIABILITY UNDER ANY PROVISION OF THIS AGREEMENT SHALL BE LIMITED TO THE AMOUNT ACTUALLY PAID BY YOU FOR THE PRODUCT. BECAUSE SOME JU-RISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

ATLONA2151 O’toole Ave, Ste D

San Jose CA 95131Toll Free: 1-877-536-3976

International: 408-954-8782FAX: 408-954-8792

Website: www.atlona.comE-MAIL: info@atlona.com

22

24

ATLONA PRODUCT REGISTRATION

Thank you for purchasing this Atlona product — we hope you’ll enjoy it.

We also hope that you’ll take a few moments to register your new purchase. Registration creates an ownership record if your product is lost or stolen and helps ensure you’ll receive notification of performance issues and firm-ware updates.At Atlona, we respect and protect your privacy and assure you that your registration information is completely secure. Of course, Atlona product registration is totally voluntary and failure to register will not diminish your limited warranty rights.

To register go to www.atlona.com/registration