ASSESSMENT METHODOLOGY GUIDE - MPAC · PDF fileASSESSMENT METHODOLOGY GUIDE . ... City of Guelph Fiat Chrysler Automobiles Cushman ... alignment of the wood particles to provide strength

ASSESSMENT

METHODOLOGY GUIDE ASSESSING VALUE-ADDED WOOD PRODUCTS

MANUFACTURING PLANTS IN ONTARIO

2016 BASE YEAR

JUNE 2015

© Municipal Property Assessment Corporation 2015 All rights reserved

This document describes the assessment methodology that MPAC currently expects

to use for the 2016 Assessment Update for properties for which the current use is as

a value-added wood products manufacturing plant and for which the current use has

been determined by MPAC to be the highest and best use. Assessors exercise

judgment and discretion when assessing properties and may depart from MPAC’s

preferred assessment methodology when assessing a particular property, however,

any deviation from these guidelines must be thoroughly documented.

This document has been prepared by MPAC to help assessed persons review how the

current value of the property likely will be determined, illustrate the uniform

application of valuation parameters to the property type and consider whether

MPAC’s subsequent assessed value is correct and equitable in comparison to the

assessed value of similar real property so as to ensure the fair distribution of the

property tax burden. The information in this document will help property owners to

meet the requirements of subsection 39.1(4) of the Assessment Act and Rule 16 of

the Assessment Review Board when providing reasons for making a Request for

Reconsideration or filing an Appeal to the Assessment Review Board.


April 30, 2015

In accordance with the direction issued by the Minister of Finance on April 18, 2015,

pursuant to subsection 10(1) of the Municipal Property Assessment Corporation Act, the

Municipal Property Assessment Corporation (MPAC) has published Assessment

Methodology Guides for the following industries:

Pulp and Paper Mills;

Saw Mills;

Value-Added Wood Products Manufacturing Plants;

Steel Manufacturing Plants;

Automotive Assembly Plants;

Automotive Parts Manufacturing Plants.

These Assessment Methodology Guides represent MPAC’s preferred assessment

methodologies in Ontario and are intended to provide clarity and transparency as to how

property types in the above mentioned industries typically will be assessed.

Antoni Wisniowski President and Chief Administrative Officer

Larry Hummel, M.I.M.A, FRICS Chief Assessor

http://www.ontario.ca/laws/statute/97o43


Acknowledgements

As part of the preparation of Assessment Methodology Guides, MPAC consulted with

affected property taxpayers, municipalities, and representatives. MPAC engaged the

International Property Tax Institute as an independent facilitator to undertake consultation

sessions which included the following industries:

Pulp & Paper Mills

Saw Mills;

Value-Added Wood Manufacturing Plants;

Steel Manufacturing Plants;

Automotive Assembly Plants;

Automotive Parts Manufacturing Plants.

MPAC would like to acknowledge and thank the following parties who participated in the

consultation process (September 2014 – March 2015).

City of Hamilton Essar Steel Algoma Inc. DuCharme, McMillen & City of Sault Ste. Marie ArcelorMittal Associates, Inc. Haldimand County Magna International Inc. Nixon Fleet & Poole LLP City of Ottawa General Motors of Canada Limited Altus Group Limited The Corporation of the City of North Honda Canada Inc. Equitable Value Inc. Bay Canadian Vehicle Manufacturers’ AEC Property Tax Solutions City of Brampton Association Prestige Property Tax Specialists City of St.Catharines Ford Motor Company of Canada Municipal Tax Equity (MTE) Corporation of the City of St. Thomas Limited Consultants Inc. City of Guelph Fiat Chrysler Automobiles Cushman & Wakefield Property City of Oshawa Resolute Forest Products Tax Services City of Vaughan Domtar Ryan Township of Southwest Oxford Tembec Boreal Appraisal Services City of Cambridge AV Terrace Bay Inc. Municipal Tax Advisory Group Town of Ingersoll Walker West Longo Town of Milton James Petrin Property Town of Oakville Assessment Services City of Greater Sudbury City of Thunder Bay Town of Espanola Township of Dubreuilville City of Thorold City of Mississauga Township of James/Elk Lake

Questions about the consultation process can be directed to [email protected].

mailto:[email protected]

© Municipal Property Assessment Corporation 2015 All rights reserved i

Table of Contents

PART 1 - INTRODUCTION ............................................................................................... 1

1.1 PROPERTIES COVERED BY THIS METHODOLOGY GUIDE ..............................................................3

1.2 LEGISLATION .....................................................................................................................8

1.3 VALUATIONS - GENERAL ......................................................................................................8

1.4 THE USE OF THIS METHODOLOGY GUIDE ..............................................................................11

1.5 CONSULTATION AND DISCLOSURE .......................................................................................11

PART 2 - THE VALUATION PROCESS - PREPARATION .................................................... 13

2.1 SIX MAIN STEPS ..............................................................................................................13

2.2 IDENTIFY WHAT NEEDS TO BE VALUED .................................................................................13

2.3 DEFINE THE BASIS OF VALUE AND DATE OF VALUATION ...........................................................13

2.4 RESEARCH - DATA COLLECTION ...........................................................................................14

2.5 ANALYSIS OF DATA COLLECTED ...........................................................................................17

2.6 THE VALUATION ..............................................................................................................18

2.7 VALIDATING THE RESULTS ..................................................................................................18

PART 3 - THE VALUATION - APPLICATION .................................................................... 19

3.1 SUMMARY OF COST APPROACH ..........................................................................................19

3.2 RECOMMENDED PROCEDURE .............................................................................................19

3.3 DEFINITION OF TERMS ......................................................................................................23

3.4 DETAILED PROCEDURE ......................................................................................................23

1. Property Evaluation ...............................................................................................23

2. Determination of Cost New ..................................................................................31

3. Identification of Depreciation ...............................................................................34

4. Quantifying Depreciation ......................................................................................44

5. Value the Land.......................................................................................................59

6. Validate the Results ..............................................................................................62

APPENDICES ................................................................................................................ 69

APPENDIX A - LIST OF PROPERTIES COVERED BY THIS METHODOLOGY GUIDE ....................................69

APPENDIX B – GLOSSARY OF TERMS ..........................................................................................71

© Municipal Property Assessment Corporation 2015 All rights reserved 1

Part 1 - Introduction

The Municipal Property Assessment Corporation (MPAC) – www.mpac.ca – is responsible for

accurately assessing and classifying property in Ontario for the purposes of municipal and

education taxation.

In Ontario, property assessments are updated on the basis of a four-year assessment cycle.

The next province-wide Assessment Update will take place in 2016 when MPAC will update

the assessments of Ontario’s more than five million properties to reflect the legislated

valuation date of January 1, 2016. Assessments updated for the 2016 base year are in effect

for the 2017-2020 property tax years. Ontario’s assessment phase-in program prescribes that

assessment increases are phased in over a four-year period. Any decreases in assessment are

applied immediately.

The accurate valuation of large special purpose industrial properties such as value-added

wood products manufacturing plants for property tax purposes presents a number of

challenges due to the size and specialized nature of the properties concerned and the fact

that very few, if any, of them are bought, sold or leased in the market on a regular basis.

For that reason, it is important to ensure that the valuation methodology applied is capable of

providing a realistic estimate of current value at the relevant valuation date which, in turn,

enables all stakeholders to understand the valuation process and have confidence in the

fairness and consistency of its outcome.

This Methodology Guide has been prepared for the benefit of MPAC assessors, property

owners and their representatives, municipalities and their representatives, Assessment

Review Board members, provincial officials, and the general public.

It should be noted that “large” in the context of industrial properties means a property that

falls within the definition of the “Large Industrial Property Class” contained in Section 14 (1) of

Ontario Regulation 282/98. In general, this refers to an industrial property in excess of

125,000 square feet in terms of “exterior measured area.”

http://www.mpac.ca/


The following definitions may be helpful in reviewing this Methodology Guide:

Special Purpose Properties:

“A limited market property with a unique physical design, special construction

materials, or layout that restricts its utility to the use for which it was built.”

[Appraisal Institute]

“Specialized property is property that is rarely, if ever, sold in the market except by way

of sale of the business or entity of which it is part, due to the uniqueness arising from

its specialized nature and design, its configuration, size, location, or otherwise.”

[International Valuation Standards Committee]

The characteristics of special purpose properties are likely to include:

Unique improvements, design, layout, size, construction materials and/or building

services that facilitate one or a limited number of uses.

Generally contains machines and machine fittings that are designed to facilitate one

purpose.

Adaptation to other uses is typically challenging requiring significant alterations and

rarely finding economically viable uses for all of the improvements.

Limited market possibilities, except as a going concern business.

Typically has specialized building services.

They tend to serve large market areas that are more regional, national or international

in scope.

The expansive geographic scope of these properties typically requires research of

regional, national or international data to support a market value analysis.

Understanding the “market” for special purpose properties also requires

understanding of the industry in which it operates, i.e., what is the nature, condition

and financial health of the potential buyers and sellers.


1.1 Properties Covered by this Methodology Guide

This Methodology Guide relates to value-added wood products manufacturing plants which

include many different types of property with a variety of processes taking place within them.

The list of properties within Ontario that are covered by this Methodology Guide change from

time to time. A current list of the properties covered by this Methodology Guide can be found

in Appendix A.

Brief Introduction to the Industry

Definition

"Value-added" is a term globally used to describe materials that have been remanufactured

from rough lumber or logs into a higher grade of finished product.

Two types of remanufactured products are generally recognized:

1. semi-finished and finished products

2. remanufactured lumber

Semi-Finished and Finished Products

Semi-finished and finished products are manufactured from commodity wood products and

may include:

engineered wood products (laminated beams, trusses, wood I-beams, etc.)

millwork (doors, windows, architectural woodwork, turnings, etc.)

cabinets (kitchen and vanity cabinets, cabinet doors, countertops, etc.)

furniture (household furniture, ready-to-assemble furniture,

commercial and institutional furniture, patio furniture, etc.)

pallets and containers

other wood products (chopsticks, ladders, toys, etc.)

Remanufactured Lumber Products

Remanufactured lumber products include all lumber or wood product outputs from a

remanufacturing process performed on sawn lumber input stock. The remanufactured process

includes subjecting lumber input stock to one or more of the following processes: change in

thickness, width, length, profile, or joining together by finger joint or otherwise. The list of

products includes:


Lumber: Sawmills produce a wide variety of grades and dimensions of lumber. Most

lumber is produced for structural purposes, when resistance to working stresses is

required. The rapidly expanding lumber industry in Eastern Canada has tended to con-

centrate on the production of "studs" - wood structural members used as supporting

elements in walls and partitions; the common stud is usually 2 in. x 4 in., 8 ft. long.

Plywood: Plywood is divided into two major categories, sheathing and sanded, although

a third segment, specialties, has become increasingly visible in recent years. Sheathing is

un-sanded structural plywood typically used for wall, floor and roof under-cladding - a

market that is shifting gradually toward oriented strand board. Sanded plywood, as the

name indicates, has a smooth surface composed of higher-grade veneers. Typical

specialties are textured exterior siding products, concrete form and marine plywood.

Oriented Strand Board (OSB): OSB is a structural panel that consists of wood strands

glued with a waterproof resin. The physical properties of the board are enhanced by

alignment of the wood particles to provide strength similar to sheathing plywood.

Producers focus on the same end-use markets as do the producers of sheathing ply-

wood. OSB's key economic advantage over plywood is that it utilizes low-cost/low-qual-

ity wood fibre.

Fibreboard (e.g., Medium Density Fibreboard/Particleboard): Fibreboard is a family of

non-structural panels manufactured from wood particles bonded with resins and

consolidated with heat and pressure. Medium Density Fibreboard (MDF) is the category of

fibreboard experiencing by far the greatest increase in capacity and demand within the

group. The manufacturing process for MDF is the same as that for the lower-quality

particleboard, except in the former the chips and other particles are reduced to individual

fibres. MDF is a high-quality product which costs more than particleboard to manufacture.

It lends itself to high-end furniture applications where machine edge and surface patterns

are employed. Finishes and overlays can be used effectively to provide a grain pattern

typical of dear lumber. Some MDF is machined into molding and other millwork products.

Laminated Veneer Lumber (LVL): LVL is an engineered wood product manufactured in

sheets of veneer which are laid up with their grains parallel and ends overlapping and

laminated with resin adhesive under heat and pressure. Typical end uses are door

headers, structural beams and wood I-joist flanges; LVL serves as a substitute for

traditional high-quality lumber.

Wood I-joists: I-joists are constructed of top and bottom flanges (or chords) of

laminated veneer lumber or sawn lumber which are separated by a web of plywood or


OSB. They are typically used to support floor and roof spans in residential and light

commercial construction, and serve as a substitute for wide-dimension lumber.

The Industry in Ontario

Ontario’s wood products industry produces a broad range of primary and secondary forest

products and is one of the most important and substantial contributors to the provincial

economy, in both northern and southern Ontario. The value of Ontario exports of softwood

lumber alone averages $1 billion annually. The wood products industry in Ontario is more

than capable of supplying high quality value-added wood products for the export market.

Ontario has 53 million hectares of productive forest area, the second largest productive forest

in Canada. The forest inventory reveals that Ontario forests are majority softwood (57%); the

rest is mixed wood and hardwood. Of Ontario’s roughly 85 million trees, the main species are

black spruce (37%), poplar (21%) and jack pine (11%). Ontario’s managed forest is 16% old

growth; 20% of the forest in parks and protected areas is old growth.

Ontario exports many of its forestry industry products; exports are affected by:

trade regulations and agreements

global economic factors

housing industry

technological change

competition

In general, the three most important categories for manufacturing costs are:

1. cost of materials and supplies

cost of energy, water and vehicle fuel

production worker wages

2.

3.

Manufacturing costs in the wood product manufacturing subsector are traditionally

dominated by the costs of materials and supplies. Considering these costs are the major factor

in its manufacturing activities, this subsector is vulnerable to any fluctuation in the prices of

materials and supplies.

There are over 2,000 manufacturers in Ontario producing value-added wood products.

Furthermore, there are more than 1,000 businesses associated with the value-added wood

products. Out of all the Canadian provinces which produce value-added wood products,

Ontario ranks first in terms of revenue.


The forests of Northern Ontario are managed to internationally recognized standards of

sustainability, and the quality of the wood fibre produced is excellent. The region is

strategically located, providing access to major world markets. The United States, especially

the Great Lakes States, is a key market for Ontario wood and paper products. Emerging

markets in Mexico and Chile also offer unique opportunities for Ontario-based forest product

companies.

The forest products industry in Northern Ontario is continuously adapting to maintain its

competitive position in the global marketplace. Companies are looking toward value-added

products such as engineered wood, speciality papers, and pre-fabricated buildings and

components.

Forest research centres in Northern Ontario, such as the Great Lakes Forestry Centre, the

Ontario Forest Research Institute, and the Centre for Northern Forest Ecosystem Research,

complement the many academic institutions offering forestry-related programs.

The majority of the Ontario’s manufactured wood-related merchandise is exported to the

United States. The northernmost states account for the greatest amount of revenue from

Ontario wood exports.

Supply and Demand Issues

The supply of value-added wood products is not easily measurable as it consists of more than

one type of product. Generally these products consist of:

semi-finished and finished wood products

remanufactured lumber

Many different technologies are employed in the manufacturing process, but they have one

common element in terms of the inputs. The main one is wood residue from sawmills. The

price of wood residue is correlated to the prices of the main inputs to the pulp and lumber

industry, softwood (and hardwood) logs. The bulk of the logs are turned into either lumber or

chips for pulp. The residue is available for input into the value-added wood products industry.

In addition some lumber is remanufactured into other wood products.

One of the major demand factors for value-added wood products is the housing industry.

Engineered wood is one of the major value-added wood products.

Engineered wood, also known as composite wood, comprises of a number of wood products

made by binding veneers, particles, fibres and strands of wood, together with adhesives to

form composite materials. They are modeled to design requirements as per the client’s


specifications and tested to meet international and national standards. They include a variety

of products ranging from plywoods to roof trusses.

There is increasing demand for cost-effective wood products for building applications such as

load bearings, structure panels and flooring. With the rising trend of green technology, certain

smart products are being encouraged which aid in reducing greenhouse gas emissions. North

American countries have initiated the establishment of green building standards in several

states and provinces. They provide momentum for certified wood products that are linked

with low emission levels.

Other Industry Issues

The value of the Canadian dollar, changes in offshore imports, the availability of skilled labour,

the cost of raw material costs and interest rates are all significant issues for the industry.

Technical issues also affect the rate of development in the industry and may impact on

product quality, product design, new product development, production costs and the

adoption rate of new technology. Using technical information to make a difference can

include:

reducing materials usage and handling activities

removing production bottlenecks

improving quality and reducing rework

increasing equipment utilization

designing products for ease of manufacturing

Knowledge and technology drive innovation that allows successful businesses to offer their

clients better, and more competitive, products or services. For the secondary manufacturing

industry, the Value to Wood program in Canada provides the direct transfer of practical,

relevant technical knowledge and assistance to help them reduce costs and improve

productivity. S

Machinery and Equipment

Value-added wood products manufacturing plants may contain large amounts of, often very

specialized, machinery and equipment.


1.2 Legislation

The main legislation governing the assessment of properties in Ontario for property tax

purposes is contained in the Assessment Act 1990 (as amended).

The Act contains important definitions, including what property is taxable and how it should

be valued.

The Act (section 1(1) Definitions) states that property must be assessed at its "current value"

which means, in relation to land:

"… the amount of money the fee simple, if unencumbered, would realize if sold at arm's

length by a willing seller to a willing buyer.”

It should be noted that, in accordance with section 3(1) 17 of the Act, all items of machinery

and equipment, and the foundations upon which they rest, used for manufacturing, though

assessable, are exempt from property taxation.

Other relevant legislation will be referred to as necessary in this Methodology Guide.

1.3 Valuations - General

Valuations of property are carried out for a variety of purposes. This Methodology Guide is

provided specifically for assessors involved in the valuation of value-added wood products

manufacturing plants for property tax purposes in Ontario and other stakeholders who have

an interest in the valuation.

The legislation governing the assessment of properties for property tax purposes in Ontario is

set out above. It requires an assessment of the current value of all relevant properties as of a

specific valuation date.

The valuation process follows a number of systematic steps intended to ensure that all

relevant data is obtained and analyzed before being used in the provision of an estimate of

the market value of the property concerned as of the relevant date.

Many professional bodies provide guidance on how the valuation process should be

undertaken and this Methodology Guide reflects the accepted guidance on the valuation of

large special purpose properties such as value-added wood products manufacturing plants.

In broad terms, the valuation process involves the following key steps:


Ensuring a clear understanding of the purpose for which the valuation is being

provided.

Researching the legal framework concerning the valuation.

Determining what needs to be valued.

Identifying the date of the valuation.

Analyzing the relevant market (local, regional and/or international depending upon the

type of property to be valued).

Considering the highest and best use of the subject property (as explained later, it is

assumed that the use of the property as a value-added wood products manufacturing

plant is the highest and best use of the property being valued for the purposes of this

Methodology Guide).

Obtaining pre-inspection data about the property to be valued.

Carrying out a site inspection of the property to be valued.

Taking appropriate measurements and recording details of other relevant information.

Carrying out an inspection of any comparable properties that may be of assistance in

ascertaining the value of the subject property.

Determining the appropriate method, or methods, of valuation to be used.

Carrying out the valuation.

Reviewing the valuation.

Finalizing and reporting the valuation.

In general, it is appropriate to consider the value of a property by three different perspectives

or approaches to value:

the direct (sales) comparison approach

the income approach

or the cost approach


As suggested by the title, in the direct (sales) comparison approach, value is indicated by

recent sales of comparable properties in the market. In the case of large special purpose

industrial properties such as value-added wood products manufacturing plants, there are

generally very few, if any, sales or other market transactions which can be relied upon to

provide an indication of market value; for this reason, the sales comparison approach is not

used in the valuation of value-added wood products manufacturing plants.

“The sales comparison approach is applicable to all types of real property interests when

there are sufficient recent, reliable transactions to indicate value patterns or trends in

the market …. When data is available, this is the most straightforward and simple way to

explain and support a value opinion …. When the market is weak and few market

transactions are available, the applicability of the sales comparison approach may be

limited. For example, the sales comparison approach is usually not applied to special-

purpose properties because few similar properties may be sold in a given market, even

one that is geographically broad. To value special-purpose properties, the cost approach

may be more appropriate and reliable.”

[The Appraisal of Real Estate, 12th edition, page 419]

In considering any sales evidence, it is critical to ensure that the property sold falls within the

same use class as the property to be valued; in the case of special purpose properties, the sale

should relate to a property that has the same highest and best use as the subject property

otherwise it is unlikely to be a reliable indicator of value.

However, if a sale of such a property does take place, it is important for the transaction to be

analyzed to see if it may provide useful information that may assist when reviewing a

valuation prepared by the application of another approach.

In the income approach or, more accurately, the income capitalization approach, value is

indicated by a property’s revenue-earning power, based on the capitalization of income. This

method requires a detailed analysis of both income and expenditure, both for the property

being valued and other similar properties that may have been sold, in order to ascertain the

anticipated revenue and expenses, along with the relevant capitalization rate. As already

indicated, in the case of large special purpose industrial properties such as value-added wood

products manufacturing plants, there are unlikely to be any sales or rents of comparable

properties from which relevant data can be obtained, so this approach is not used.

However, it may be necessary to consider both the income and expenses of value-added

wood products manufacturing plants when looking at depreciation within the cost approach;

in particular, in considering the issue of obsolescence.


In the cost approach, value is estimated as the current cost of reproducing or replacing the

improvements on the land (including buildings, structures and other taxable components),

less any loss in value resulting from depreciation, and then adding the market value of the

land.

The cost approach is the most appropriate method of valuing large special purpose industrial

properties such as value-added wood products manufacturing plants and will therefore be the

subject of detailed guidance in the following parts of this Methodology Guide.

Using the cost approach also helps to exclude the value of the business being carried out

within the property and is one of the reasons why this method of valuation is used for value-

added wood products manufacturing plants.

1.4 The Use of this Methodology Guide

This Methodology Guide is intended to:

Ensure that value-added wood products manufacturing plants are assessed at their

correct current values.

Ensure the assessments of value-added wood products manufacturing plants are fair,

accurate, predictable, and transparent.

Provide direction to assessors to ensure that MPAC takes a consistent approach to

valuing value-added wood products manufacturing plants.

Ensure that MPAC’s methodology for valuing these properties is well documented and

aligns with industry standards for market valuation in a mass appraisal environment.

Explain MPAC’s valuation methodology to municipalities, taxpayers, ARB members and

other stakeholders.

MPAC assessors are expected to follow the procedures in the Guide. However, this Guide is

not intended to be a substitute for an assessor’s judgment in arriving at the current value for a

particular property.

1.5 Consultation and Disclosure

MPAC is committed to providing municipalities, taxpayers and all its stakeholders with the

best possible service through transparency, predictability and accuracy. In support of this


commitment, MPAC has defined three levels of Disclosure as part of its delivery of the 2016

province-wide Assessment Update.

Three Levels of Disclosure (2016 Assessment Update)

Level 1 – Methodology Guides explaining how MPAC approached the valuation of particular

types of property; in this case, value-added wood products manufacturing plants.

Level 2 – Market Valuation Reports explaining how the methodology outlined in Level 1 has

been applied at the sector level for the purposes of each assessment.

Level 3 – Property Specific Valuation Information, available to property taxpayers, their

representatives and municipalities.


Part 2 - The Valuation Process - Preparation

2.1 Six Main Steps

2.2 Identify What Needs to be Valued

The assessor needs to identify the extent of the property to be valued. The definition of land

is all encompassing. Land includes not only the land itself (“terra firma”) but also buildings,

structures, machinery and fixtures, or any part of such items.

2.3 Define the Basis of Value and Date of Valuation

The definition of value was identified previously and is the "current value" of the property

which, in accordance with the Act, is:

"… the amount of money the fee simple, if unencumbered, would realize if sold at arm's

length by a willing seller to a willing buyer.”

This means that the assessor is concerned with the “market value” of the property and

therefore needs to consider what data is required to enable an assessment of market value to


be prepared as of the relevant valuation date. It should be noted that, for the purposes of this

Methodology Guide, “market value” and “current value” have the same meaning.

The relevant valuation date will differ for each four-year reassessment. The assessor should

be clear about what valuation date is to be used for the particular reassessment.

In preparing a valuation, the assessor will need to take into account all relevant, value-

significant evidence available that may assist in determining the value of the particular value-

added wood products manufacturing plant as of the valuation date. The market conditions,

i.e., the economic circumstances that underlie supply and demand, that give rise to value are

likely to change between reassessments, so it is important to ensure that only those factors

that are relevant as of the specified valuation date are taken into account.

However, the assessor should have regard to the physical circumstances at roll return and

value the land and improvements as they exist at that time, assuming a sale on the valuation

date or at a later date if there have been changes to the property after the reassessment date.

2.4 Research - Data Collection

Data collection involves two main activities:

1. Collection of data relating to the value-added wood products manufacturing plant to

be valued.

2. Collection of market evidence or other data that will assist in the valuation.

Collection of Data Relating to the Value-Added Wood Products Manufacturing Plant

to be Valued

The assessor should start by considering what information is available from current MPAC

records concerning the property and then checking to ensure it is accurate and up to date.

The following types of data relating to the property to be valued need to be collected:

If recent, purchase price/date, and/or construction costs, relating to the property.

Layout plans, building plans, elevations, cross-sections, specifications, etc., relating to

the property.

A description of the process (or processes) undertaken at the property.


Specific and detailed information concerning:

o the use of each part of the property

o the functionality (what it does and how well it does it) of the property

o the utility (i.e., the usefulness) of the property

o the productive capacity of the property

o recent/projected trends in production

o recent/projected trends in the cost of inputs

o recent/projected trends in the value of outputs

o recent/projected trends in profitability

Any particular aspects of the value-added wood products manufacturing plant that

create inefficiencies.

Any repairs or other remedial works that are required or planned.

Any plans to change the existing manufacturing operation.

Any plans to alter, extend or demolish any parts of the property (and why).

How the existing property compares with a modern equivalent facility (and the

location and other details concerning a modern equivalent value-added wood

products manufacturing plant).

Information with regard to the zoning of the property.

Information about the locality in which the property is situated.

Any other relevant information that may be available from other sources concerning

the property (e.g., company accounts, the municipality, the Internet, etc.).

Information available about competition from other value-added wood products

manufacturing plants.

Property Inspection

The assessor should take steps to collect the above information either in advance of a

property inspection or during a property inspection. A property inspection will provide the

following data:

Confirmation of the data (size, layout, etc.) contained in plans, drawings, etc.


Confirmation of the use of the various buildings, structures, etc.

Details of the age/condition of the buildings, structures and other improvements.

Confirmation of the information provided in respect of necessary repairs, etc.

Details of any cost estimates provided in respect of necessary repairs, etc.

Photographic record of the site, building, structures, other improvements, etc.

Details of any other matters noted - positive or negative - with regard to the property.

Commentary on the location of the property, transport links and access to the site.

The above factors should be used as a check-list by the assessor to ensure that all relevant

information is obtained prior to the valuation being undertaken.

How the information obtained may be used in the valuation is shown and discussed in Part 3

of this Methodology Guide.

Collection of Market Evidence or Other Data that will Assist in the Valuation.

In the case of many types of property, market value can be derived from the evidence of sales

or leases (rentals) of similar properties in the same locality as the property to be valued.

However, in the case of large specialized properties such as value-added wood products

manufacturing plants, such market data is unlikely to be available in sufficient volume to

provide a reliable indication of value.

Nevertheless, the assessor should seek whatever data may be available in terms of sales,

leases, etc., of similar large industrial properties and consider whether or not such data may

provide evidence that could assist in the valuation of a value-added wood products

manufacturing plant.

In addition to collecting data about the value-added wood products manufacturing plant to be

valued, and any market evidence that may exist, the assessor needs to carry out wider

research that will assist in determining the value of the subject property. Such research is

likely to include:

The state of the value-added wood products manufacturing industry. For example,

the economic situation, supply and demand factors, etc., in Ontario, Canada, North

America, and possibly worldwide.


Trends in the value-added wood products manufacturing industry. For example,

whether it is growing, shrinking, or there have been any changes in manufacturing

techniques, etc., in Ontario, Canada, North America, and possibly worldwide.

Any evidence available to indicate the value of the properties used in the value-added

wood products manufacturing industry. For example, sales, leases, construction costs,

etc., in the municipality, Ontario, Canada, and North America.

Much of the information required about the state of the industry, economic trends, etc., will

be contained in the Market Valuation Reports that form part of MPAC’s Level 2 Disclosure (see

section 1.5). The assessor should ensure that the information contained in that report is

properly reflected in the valuation to the extent that it has an impact on the value of the

individual value-added wood products manufacturing plant.

Confidentiality

As outlined above, it is important to be aware that, in order to enable MPAC to produce an

accurate valuation of the property concerned, information needs to be obtained from a

variety of sources.

This will include information from MPAC’s records, from the owner or operator of the

property, from the municipality in which the property is located, from the assessor’s visit to

the property, and from other sources.

All stakeholders in the property tax system have an interest in ensuring that the current value

provided by MPAC is correct; in order to achieve this, it is necessary for all parties to

cooperate in the provision of information.

It is appreciated that some of the information outlined above may be of a commercially

sensitive nature. MPAC recognizes the need to ensure that any information provided to them

is properly safeguarded and only used for the purpose for which it is supplied. Assessors

should appreciate the nature of this undertaking and ensure data is treated accordingly.

If after an appeal has been filed, MPAC receives a request for the release of actual income and

expense information, or other sensitive commercial proprietary information, the usual

practice is to require the person seeking the information to bring a motion before the

Assessment Review Board, with notice to the third parties, requesting that the Assessment

Review Board order production of the requested information. The release of such information

is at the discretion of the Assessment Review Board.


Exception

S. 53 (2) This section does not prevent disclosure of that information, (a) to the assessment corporation or any authorized employee of the corporation; or

(b) by any person being examined as a witness in an assessment appeal or in a proceeding in court involving an assessment matter. 1996, c. 4, s. 43; 1997, c. 43, Sched. G, s. 18 (34).

2.5 Analysis of Data Collected

Having carried out the data collection outlined previously, the assessor needs to analyze it and

reach a conclusion regarding the appropriate valuation method to use and how it should be

applied.

As already indicated, for the purposes of this Methodology Guide, it is assumed that the

assessor will conclude that there is insufficient evidence available to enable either the direct

comparison approach or income approach to be adopted. For that reason, the assessor will be

adopting the cost approach and using the data collected to ensure that the cost approach is

properly applied.

2.6 The Valuation

Having undertaken the necessary steps outlined above, the assessor should now be in a

position to apply the appropriate valuation model. In the case of large value-added wood

products manufacturing plants, the assessor will be using the cost approach and detail on how

that model should be applied is contained in Part 3 of this Methodology Guide.

2.7 Validating the Results

Once the assessor has completed the valuation, it is necessary to validate the results by

carrying out a series of checks to ensure that all relevant parts of the property have been

included in the valuation, that there has been no double-counting of any adjustments made

for depreciation, that the resulting valuation has been compared with any market evidence

that may be available in relation to value-added wood products manufacturing plants or

similar properties, and that the final valuation is in line with the valuation of other similar

properties in Ontario.


Part 3 - The Valuation - Application

3.1 Summary of Cost Approach

As already indicated, the primary valuation approach to be used for the valuation of value-

added wood products manufacturing plants is the cost approach.

Using the cost approach derives a value by estimating the cost to replace the functionality and

utility of a property. In broad terms, this requires six main steps:

This Methodology Guide is designed to assist the assessor to navigate through the valuation

approach and produce an accurate estimate of current value of value-added wood products

manufacturing plants utilizing the recognized cost approach methodology.

3.2 Recommended Procedure

The Methodology Guide recommends a valuation process with the six main steps outlined

above. Additional detail about each of those steps is set out below:


1. Property Evaluation

Evaluate the property’s functionality (what it can do).

Evaluate the utility of the property (the expected benefits to be derived).

2. Determine Reproduction Cost New

Establish the value of the subject property by using a cost manual (i.e., MPAC’s

Automated Cost System - ACS) to determine reproduction cost as new.

3. Identify Depreciation

Evaluate the physical state and condition of the property.

Consider how the functionality and utility of the subject property compares to a

modern and efficient property.

4. Quantify Depreciation

Apply a breakdown approach to depreciation whereby each separate element of

depreciation is identified and applied, as follows:

o Apply physical depreciation due to age from the typical depreciation tables

found in the cost manual.

o Make adjustments as required to age-related depreciation due to the actual

state and condition of the property.

o Apply functional obsolescence as required.

o Apply external obsolescence as required.

5. Value the Land

Estimate the market value of the land and add it to the value of the improvements.

6. Validate the Results

Apply checks - age-life and market extraction (if market data available) - to ensure that

there has been no double-counting of adjustments and the final valuation is consistent

and accurate.


This Guide is designed to assist the assessor in the application of the cost approach to

establish the current value assessment of value-added wood products manufacturing plants. It

does not replace the assessor’s judgment.

The chart on the following page summarizes and outlines the six main steps in the valuation

approach.


Outline of the Cost Approach Process


3.3 Definition of Terms

Each of the steps outlined in the chart above will be considered in detail in this Methodology

Guide. Where appropriate, terms are defined as they are encountered in the text but, in

addition, there is a Glossary of Terms in Appendix B.

3.4 Detailed Procedure

The following steps should be followed when valuing a value-added wood products

manufacturing plant. The assessor should always bear in mind that it is the actual property

that is being valued, even though consideration may be given to how the actual property may

be replaced by a different type of property (in terms of size, layout, etc.) when considering

valuation issues such as functional obsolescence.

1. Property Evaluation

The first step in the process is to determine the type of property being valued and whether it

falls within the property types, i.e., value-added wood products manufacturing plants,

covered in this Methodology Guide. Once satisfied that it does, the assessor needs to collect

the information required to establish the current value of the property.

Part 2 of this Methodology Guide outlined the nature of the information to be collected prior

to the valuation being carried out. The notes below add more detail about this process.

Review Assessment Records

Typically, there is some historical information on file in the assessment records, or available

from assessment databases. The assessor will need to check this information carefully and

ensure it is accurate and up to date.

In particular, the assessor should check MPAC’s applications, i.e., the Integrated Property

System (IPS) and the Source of Uniform Records for Cost Evaluation (SOURCE).

Information from the Municipality

The municipality should have provided MPAC with plans, etc., but the assessor needs to check

to ensure they are the latest plans, drawings, etc. The drawings required include the

following:

plot plan(s)


floor plan(s) - including horizontal measurements

elevations - including vertical measurements

cross-sections of the buildings

Ideally, these drawings, plans, etc., should be in electronic (e.g., CAD) format. The assessor

should also check with the municipality to see whether it holds any other relevant information

about the property that may be useful in the valuation process.

Information from the Owner

It is important to set up an appointment with the owner or operator to inspect the property

and to discuss the operations that take place at the property. Part 2 of this Methodology

Guide outlines the type of information that should be sought from the owner or operator of

the property either before or during the inspection.

Review Municipal Plans

Municipalities have zoning and planning information available for all properties, especially

areas in transition where there are often special studies or Secondary Planning documents.

This type of information will be helpful in confirming that use as a value-added wood products

manufacturing plant is the highest and best use of the property and may assist in gaining a

wider appreciation of value-significant features of the locality.

Internet

Along with maps and photographic records, the Internet has general information on most

properties. Some of this information may be out of date, but a search of the Internet can

often provide useful information about the nature of the area and the market. Articles about

value-added wood products manufacturing plants selling or being re-developed, information

and statistics on value-added wood products manufacturing and related manufacturing

sectors, and general economic information can all be found on the Internet.

Property Inspection

The value of any large industrial property relates to its utility; how well/efficiently it serves as

a base for the process for which it is used, i.e., in this case, a value-added wood products

manufacturing plant. Understanding a property and its utility requires a property inspection to

gain insights into the condition and utility of the property and the nature of the locality and

surrounding properties.


Before inspecting the property, the following steps are recommended:

Prepare a list of questions that need to be asked (see Part 2 of this Methodology

Guide).

Arrange with the owner/operator to see the interior of the plant.

Check with the owner to see if there are any safety requirements for the tour (hard

hat, special shoes, safety glasses, high-visibility vest, etc.).

If possible, review the site plans, building plans, floor plans, elevations and cross-

sections.

Take a camera (ensure owner has provided permission for interior photos).

Take a notebook, recording device or inspection sheet to note the nature, state and

condition of the plant and any other properties inspected.

If the plant requires measurement, take a measuring device.

Let the owner know how long the inspection should take.

Inspecting the Property

Take notes about the location of the plant.

Note the access and egress to the plant.

Review the use and condition of the parking lot.

Ask questions about how the plant functions.

Ask questions about other value-added wood products manufacturing plants which

may be used as benchmarks.

Make notes of conversations as well as items seen during the inspection.

Note the condition of the improvements (buildings, structures, etc.).

Take photographs as required (with permission).

The inspection should establish all relevant details about the site improvements, their

construction, condition, use, function and utility. Also, the property inspection provides an


opportunity to ensure that the record includes all the items that should be assessed, and that

all items previously captured are still present in their stated form.

Details should be confirmed and notes made about the quality and type of construction

materials and finishes used for the following:

landscaping

site preparation

foundations

framing

walls

floors

ceiling structures

roof coverings

plumbing

lighting/electrical

heating, ventilation, air conditioning (HVAC)

doors

elevators

stairs

fire systems and sprinklers

finishes

paving

yard improvements

other assessable items


availability of municipal services

The state and condition of these improvements should also be noted and comments made

about whether a possible variance should be applied to the effective age of any improvement.

The assessor should take photographic records to supplement notes.

Assembly and Verification of Data

Once the property has been inspected, the assessor should use the observations to refine the

data available and consider the application of the valuation process:

Are there any valuation issues to be taken into account with respect to the subject

property or its location?

Are there any comparable properties that need to be considered?

Is there any other new information to be considered?

Is any additional research needed?

The assessor should now take steps to verify the data, to ensure that the records about the

property are accurate, and that the data concerning any transactions relating to other

comparable properties properly reflect market conditions.

Check Record of Improvements against Inspection Notes

The assessor needs to check to ensure existing records are up to date. Upgrades to building

components such as roofing, lighting, and HVAC systems (those components with a shorter

lifespan) often occur; small additions are also made. The building records need to be updated

to reflect the current state and condition of the property.

Evaluate Functionality and Utility

Utility reflects the use or usefulness of a property. The amount of utility is a measure of the

benefits likely to be generated in the foreseeable future. Functionality concerns what a

property can do and how efficiently it can perform those tasks. The more efficient and

functional a property is, the greater the benefits that can be generated, the higher the utility,

and the higher the value. The assessor needs to have a clear understanding of both the

functionality and the utility of the value-added wood products manufacturing plant to enable

an accurate valuation to be prepared. Due to the specialized nature of the value-added wood


products manufacturing operation, the assessor will need to discuss both functionality and

utility with the owner or operator of the plant.

Functionality

Evaluating the functionality and utility of a property requires points of comparison. Some

points are general in nature; for example, a value-added wood products manufacturing plant

with a lot of excess space tends not to be as efficient in terms of operating costs when

compared to a plant of a more appropriate size. Some points are specific to current

operations; for example, a disjointed production flow. In both instances, the assessor has to

understand the most appropriate replacements for the existing improvements and whether

existing functionality and utility conditions affect the value of the property in comparison to a

more efficient value-added wood products manufacturing plant.

Establishing how well a property fulfills its desired functions requires knowledge of both the

property and the processes being carried out there. An inspection may provide visual clues

about how well the property works. The assessor should take note of any unused areas,

excess or insufficient space or heights, or any process that seems inefficient, disjointed or out

of place. Such occurrences may indicate the presence of functional obsolescence. However, a

more complete determination of functionality and utility requires input from the operator of

the property.

Functionality Questions

There are a number of questions that may help to build up a picture of the functionality of a

value-added wood products manufacturing plant; these include:

Are there any areas where the building layout or design makes the process difficult or

inefficient?

Are there any unused areas?

Are there excess heights?

Is the clear height sufficient?

Is access to the site adequate?

Is the site large enough/laid out for current operations?

Is the process disjointed?


Are the property services adequate?

How well do the building services work?

Are the improvements in good condition?

Has the intended use of any of the improvements changed?

Is the property working one, two or three shifts?

How easy would it be to adapt the process to incorporate recent technological

developments? (i.e., how flexible is the layout?)

What is the cost of production compared to a modern, efficient value-added wood

products manufacturing plant?

What components of the plant meet modern standards?

This Methodology Guide is concerned with the valuation of value-added wood products

manufacturing plants; the primary concern therefore is to assess how well the property meets

the needs of a value-added wood products manufacturing operation. However, if the property

could be used for other similar purposes, possibly a different type of value-added wood

products manufacturing, consideration will need to be given to evaluating the functionality

and utility of the property in relation to other possible uses.

Evaluate Property Utility

Utility is the ability of a property to satisfy a particular want, need or desire.

Functional utility is represented by the ability of a property or building to be useful and to

perform the function for which it is intended, according to current market needs and

standards; in other words, the efficiency of a building in terms of architectural style, design

and layout.

Utility in the valuation process is addressed in the highest and best use analysis through

consideration of the use of the property that produces the most profitable return.

Highest and Best Use

Determining the highest and best use is fundamental to establishing the current value of a

property. It requires that the value determined be the highest amount that could be obtained


for the reasonable use of that property under the current zoning environment. The market

value of a property is predicated on a determination of highest and best use as defined below:

“The reasonably probable and legal use of vacant land or an improved property

that is physically possible, appropriately supported, financially feasible, and that

results in the highest value.”

[The Appraisal of Real Estate, third Canadian edition, page 12.1]

This definition is further qualified as follows:

Legal uses are those that qualify under existing government regulations – especially

zoning by-laws.

Uses that are physically possible on the subject site are uses that could be

accommodated within the site configuration, location, size, or soil conditions.

Appropriately supported uses restrict the potential options to uses that would be

reasonably and probably considered by the market.

Financial feasibility means the need for probable economic success of a potential

use.

The highest and best use must be the most profitable use for the entire property

collectively – land, buildings, and other improvements.

The process of establishing highest and best use considers each of these points; eliminating

uses that do not qualify under the various criteria and evaluating the feasibility and value of

uses that meet the criteria.

A review of the state and condition of the improvements, the functionality of the property,

and the expected utility allows for a more informed judgment on the highest and best use of

the property.

In general, it is assumed that the highest and best use of a value-added wood products

manufacturing plant is likely to be the existing use. However, the question of highest and best

use should still be examined to confirm this assumption.

When considering an alternative highest and best use, it is important to remember the

principle of consistent use; this means the existing improvements have to be valued according

to how well they may serve that alternative use.


For the purposes of this Methodology Guide, it is assumed that the highest and best use of the

property to be valued is as a value-added wood products manufacturing plant.

2. Determination of Cost New

The application of the cost approach to determine the current or market value of a property is

based on the concept that it is possible to establish what it would cost a notional purchaser to

replace the property with another of equal utility. When a property is new, or has very little

life remaining, it is relatively easy to rationalize the amount such a purchaser would pay. It is

the value during the period in between those two extremes that present challenges; this is

where the task of ascertaining replacement costs, and identifying and quantifying

depreciation, is necessary to enable the determination of current value.

The cost approach derives a value by estimating the cost to replace the functionality and

utility of a property. As a reminder, in broad terms, this requires six steps:

1. Determine the functionality and utility of the property (what the property can do and

how well it does it).

2. Establish the costs as new to construct the improvements that can complete these

functions.

3. Identify all forms of depreciation.

4. Quantify all forms of depreciation (the difference between the cost as new and the

market value of the improvements, i.e., the amount the improvements would sell for

as of the valuation date).

5. Add the market (i.e., current) value of the land to the depreciated value of the

improvements.

6. Validate the results of the above process.

Given the means to establish the cost new, i.e., using MPAC’s costing system (ACS), the cost

approach can be applied to value value-added wood products manufacturing plants. This

Methodology Guide is designed to assist the assessor to navigate through the valuation

process and produce an accurate estimate of current value utilizing the recognized cost

approach methodology.


Reproduction Cost New

Having assembled all the data needed to complete the cost analysis, including an inspection of

the property, the next step is to derive a reproduction cost new.

Reproduction cost is defined by the Appraisal Institute as follows:

“The estimated cost to construct, as of the effective appraisal date, an exact duplicate

or replica of the building being appraised, insofar as possible, using the same materials,

construction standards, design, layout, and quality of workmanship, and embodying all

the deficiencies, super-adequacies, and obsolescence of the subject improvements.”


The assessor should be aware that it is sometimes advocated that the cost approach should

start by using the replacement cost rather than reproduction cost. However, there are risks of

inconsistency and double-counting within the valuation if replacement cost is used as the

starting point. It should always be remembered that it is the actual value-added wood

products manufacturing plant which has to be valued, not a different property. That is why it

is important to start the valuation processing by ascertaining the reproduction cost new of the

actual plant.

Replacement cost is defined by the Appraisal Institute as follows:

“The estimated cost to construct, as of the effective appraisal date, a substitute for the

building being appraised using contemporary materials, standards, design, and

layout.”


In general, the assessor should start the cost analysis with reproduction cost new, although

the use of replacement cost may be used at a later point in the valuation when considering

the impact of depreciation.

Developing Cost New

After collecting the data, the assessor should evaluate the existing improvements and select

the components from the information found in the ACS system that best reflects the existing

materials and construction styles according to the quality and functionality of those

improvements. Adjustments for replacement materials are discussed below.


Cost estimates of other structures and improvements such as yard improvements, fences,

paving, lighting, etc. are then added.

Once the cost parameters are entered, the ACS system will provide a summary of

reproduction costs new for the value-added wood products manufacturing plant. It is then a

matter of determining any adjustments to reflect depreciation.

The ACS system produces cost estimates that reflect a “whole building”, i.e., foundations,

floor structure, frame and span, exterior base walls and additives, roof finishes, interior

finishes, building services (including electrical, plumbing, HVAC, fire protection, etc.) and other

built-ins.

The assessor should be aware that ACS component costs include labour, material and

equipment prevailing at the relevant valuation date; costs also reflect geographical variations

within Ontario.

An example of the output from the ACS system is shown in Table 1.

Table 1


3. Identification of Depreciation

Depreciation has been defined as:

"The loss in utility and hence value from any cause."

[Basics of Real Estate Appraising, Appraisal Institute of Canada, 1991, page 284]

Depreciation is the difference between costs new and the market value of the property

improvements. There are three classes of depreciation to consider:

1. Physical Depreciation

2. Functional Obsolescence

3. External Obsolescence

Both physical and functional depreciation can be sub-divided into two types:

1. Curable (where it is cost-effective to fix).

2. Incurable (where it is not cost-effective, or impossible, to fix).

All elements of depreciation affect the value of a property.

Physical depreciation - deterioration due to age - is a relatively simple and straightforward

concept and is therefore widely understood, but functional and external obsolescence are

more complex. Various definitions of functional and external obsolescence exist, but the

following are used by the Appraisal Institute:

“Functional obsolescence is caused by a flaw in the structure, materials, or design of

an improvement when the improvement is compared with the highest and best use and

the most cost-effective functional design requirements at the time of the appraisal. A

building that was functionally adequate at the time of construction can become

inadequate or less appealing as design standards, mechanical systems, and

construction materials evolve.

Functional obsolescence is attributable to defects within the property lines, in contrast

to external obsolescence, which involves conditions outside the property lines and

therefore outside the control of the owner and occupants. Functional obsolescence,

which may be curable or incurable, can be caused by a deficiency - that is, some aspect

of the subject property is below standard in respect to market norms. It can also be


caused by a super-adequacy - that is, some aspect of the subject property exceeds

market norms.”


“External obsolescence is a loss in value caused by negative externalities, i.e., factors

outside a property. It is almost always incurable. External obsolescence can be

temporary or permanent. For example, value loss due to an oversupplied market may

be regained when the excess supply is absorbed and the market works its way back to

equilibrium. In contrast, the value loss due to proximity to an environmental disaster

may be permanent.

In the aftermath of the financial crisis of 2008, external obsolescence in oversupplied

real estate markets was significant, but those losses in value were not expected to be

permanent in areas where the economic base was sufficiently diverse to eventually

recover. External obsolescence is sometimes called economic obsolescence because

economic factors outside the control of property owners, like mortgage interest rates

and changing employment levels, can have large effects on the value of real estate.

External obsolescence usually has a market-wide effect and influences a whole class of

properties, rather than just a single property. However, external obsolescence may

affect only one property when its cause is location, e.g., proximity to negative

environmental factors or the absence of zoning and land use controls. In fact, the

causes of external obsolescence can be broadly characterized as either market

obsolescence or locational obsolescence. Most properties experience market

obsolescence from time to time as a result of the natural expansion and contraction of

the real estate market. In contrast, locational obsolescence is caused by proximity to

some detrimental influence on value such as heavy traffic, a landfill, or other

undesirable land use outside the property being appraised. For both market and

locational obsolescence, the value-influencing factor is outside the property and

outside the control of the property owner and occupant.”

[The Appraisal of Real Estate, 14th edition, pages 632-633]

Depreciation can be quantified in a number of ways (see step 4 below), but in order to help

with the quantification process, it is first important to identify all the forms of depreciation

that are present at the value-added wood products manufacturing plant.


Identifying Depreciation due to Age

All properties suffer physical decline as they age. The amount of depreciation applied

depends on three factors:

1. The expected life assigned to the building or structure.

2. The quality of the construction.

3. Whether any variance to the effective age has been identified by the assessor.

Improvements - Life Expectancies

The life of an improvement can be characterized in three different ways:

1. Economic life – the period where the utility of the improvement is positive, i.e., it

contributes to the value of the operation. An improvement can have more than one

economic life under different uses.

2. Useful life – the period of time over which the components of the improvement may

reasonably be expected to perform the functions for which they are designed1.

3. Physical life – the period until an improvement deteriorates to the point where it

becomes unusable.

Age-related depreciation is generally applied on the basis of the effective age of a structure2.

A brand new value-added wood products manufacturing plant has very little depreciation (if

any), whereas a value-added wood products manufacturing approaching the end of its

economic life is likely to have a significant amount of depreciation.

The ACS system reflects physical depreciation from normal wear and tear by reference to

useful life tables. However, where necessary, the assessor can override the age-related useful

life table by using an effective age input. It should be noted that overriding the ACS age-

related table can lead to difficulties and inconsistencies within the valuation, so it should be

done with caution and only where it is clearly warranted.

1 The Appraisal of Real Estate – Third Canadian Edition, Sauder School of Business, page 19.6

2 Effective age should relate to the state and condition of the improvements taking into account when the

improvements were built and their remaining economic life; however, the average actual build date of the

improvements (weighted by size or costs new) is often used as a proxy for effective age.


Quality of Construction

There are typical life expectancies for all types of industrial improvements depending on their

construction and use. For example, typical metal frame construction tends to have a 50 year

life expectancy. In general, the more robust the improvements, the longer the life expectancy.

Most buildings found at a value-added wood products manufacturing plant would be assigned

a typical expected useful life based on construction styles. However, there are/may be some

more intensive or specialized uses at a particular value-added wood products manufacturing

that tend to shorten the life of a property due to greater physical wear and tear.

Variances in Effective Age

If additional depreciation is required to adequately capture the difference in value between

cost new and current value, it can be accomplished by adjusting the effective age or adjusting

the expected useful life. However, the assessor should note the concerns about making such

adjustments stated previously.

A determination of effective age is completed by evaluation of the physical state and

condition of the improvements. If the condition of the improvements is typical for the age of

the structure, then no adjustments are required. If the improvements are worse than typical,

then an age variance can be applied (assigning an older effective age increases the

depreciation). If the improvements have recently been upgraded or renovated, then the

effective age can be raised; this lowers the amount of age-related depreciation applied by the

ACS cost system.

Evaluating Physical State and Condition

During the inspection, items that were in poor repair should have been noted. Items in poor

repair should be addressed as follows:

Does the item requiring repair or replacement change the remaining useful life of

the property or that part of the property that is affected? The assessor should

attempt to determine from the owner or operations personnel if there are any

excess operating costs associated with the condition.

If repair or replacement is required in the immediate future, the assessor should

request any information or studies completed on the estimated costs.


If the condition of the improvement changes the effective age of the component, the

physical depreciation of that component should be adjusted to reflect its change in

value.

If the repair or replacement is a matter of deferred maintenance, the assessor

should determine if the condition changes the amount that a purchaser would pay

for the property.

The assessor should make a note of the improvements/items requiring additional

consideration.

If the improvement is in poor condition, has suffered from unusual environmental conditions

(for example, flooding), or has been poorly maintained, then the effective age should be

adjusted to indicate an older building; this will result in higher rates of depreciation.

Deferred Maintenance and Cost to Cure

In addition to general depreciation due to age, there may be specific elements in the value-

added wood products manufacturing plant that require more detailed analysis: for example,

the property, or part of it, may be in need of a new roof in order to continue operations.

Deferred maintenance occurs when the property has not been properly maintained and the

item (e.g., a leaky roof) suffers from premature loss in value. Cost to cure issues arise when, in

the normal life of the property, a particular item (e.g., the roof) has to be replaced.

In both instances, i.e., the need to repair or replace, the potential purchaser of the value-

added wood products manufacturing plant would be out of pocket by the amount it would

cost to fix the issue. In both instances, after the problem is fixed, the value of the property will

increase. However, until the money is spent on remedial works, the property is affected by

depreciation.

Clearly the typical purchaser would pay more for a value-added wood products manufacturing

plant with a fully effective roof than a plant with a leaky one (all other factors being equal). If

the replacement of the building component would be done by a purchaser as of the valuation

date, then any value remaining in the component being replaced should be deducted from the

property value. If the condition exists, but only calls for remedial action over time, then only a

portion of the existing value should be deducted.

However, there is typically an additional element of depreciation involved as well: the

difference in the cost of repair versus the cost to install the building component as if it were

being constructed when new.


The amount of this depreciation is often difficult to quantify. Whereas ACS will be able to

provide an estimate of how much it costs to build a roof as new, the cost to fix/rebuild an

existing roof can be more challenging to estimate. For example, assume a value-added wood

products manufacturing company does not want (or cannot afford) to stop normal production

and, as a result, the roof work has to be undertaken at night during the time when a third shift

would be in place. In such a case, all construction materials and equipment would have to be

put away before production resumed in the morning. The cost of completing the repair work

in this way would be much higher than building a new roof in a new value-added wood

products manufacturing plant. Typically, the estimates for such cost to cure projects are not

readily available, so an estimate has to be made.

Despite these limitations on calculating an accurate depreciation amount for cost to cure, it

remains important to identify situations where such depreciation exists and to make some

form of deduction from value. Such adjustments may best be done by increasing the effective

age of the structure to increase the amount of physical deterioration applied.

Table 2 shows a simple example of the difference between the cost of a roof component at

the time of constructing a new value-added wood products manufacturing plant and the cost

to replace one in situ, i.e., the cost to cure to be deducted from the reproduction cost new.

Table 2

Item Cost (as part of RCN – ACS) Cost to Cure (separate cost)

Roof $150,000 $200,000

Ancillary works $25,000 $50,000

Total $175,000 $250,000

Curable physical

deterioration

$250,000

Table 3 shows a more detailed example of excess costs and their impact on value.


Table 3

Obsolescence

Annual Excess

Costs

Costs of

Correction

Capitalization

of Costs @

Affect on

Value

6.4176

1. Heating $1,128,518 $3,954,100 $7,242,377 $3,954,100

2. Security $500,698 n/a $3,213,279 $3,213,279

3. Clear Heights $1,126,100 n/a $7,226,859 $7,226,859

4. Material Flow $1,274,000 n/a $8,176,022 $8,176,022

5. Roof Conditions n/a $809,905 $809,905

6. Paving Conditions n/a $662,101 $662,101

Totals $4,029,316 $5,426,106 $24,042,267

Note: Assumes a discount rate of 10% and a life expectancy of 10 years.

Functional Obsolescence

The two main questions in relation to functional obsolescence that need to be considered by

the assessor are:

1. Identification - does it exist and, if so, what type of functional obsolescence is it?

2. Quantification - what method should be used and how should it be applied?

Identifying Functional Obsolescence

The existence of functional obsolescence can often be identified by addressing several

questions:

1. Are there excess operating costs inherent in the operation of the existing

improvements?

2. Are there any inefficiencies in the improvements - excess space, excess height, or

disjointed layout/construction?

3. Could the existing improvement be replaced with a more modern, efficient

substitute, and, if so, what would the modern replacement building consist of?

4. How would a potential vendor or purchaser view this property?


These questions should be discussed with the value-added wood products manufacturing plant

operations or facility manager. The assessor should attempt to get a sense of the seriousness

of the problems encountered (if any) in the operation of the property. It is also necessary to

determine whether these problems relate to the real estate alone or a combination of real

estate, machinery and equipment and/or other business factors.

A value-added wood products manufacturing plant that is inefficient or costs more to produce

an item than its modern counterpart may be suffering from functional obsolescence and may

have lost some value. One way to measure this impact is to establish the amount of the excess

operating cost and convert it into a present value. For example, an older, inefficient HVAC

system in a particular building may cost $25,000 more per year to operate than a more

modern system.

It is sometimes difficult for the assessor alone to make such a determination. Assistance is

often required from the value-added wood products manufacturing plant owner or operator.

Typical examples of excess operating costs include:

Excess costs of heating or other services.

Excess costs of internal goods movement due to inefficient layout.

Excess maintenance costs.

Costs of carrying excess space.

By addressing these and similar questions, it becomes possible to identify the presence of

functional obsolescence. Methods of quantifying this obsolescence are discussed in the next

section of this Methodology Guide.

External Obsolescence

As with functional obsolescence, the two main questions in relation to external obsolescence

that need to be considered by the assessor are:

1. Identification - does it exist and, if so, what has given rise to the external

obsolescence?

2. Quantification - what method should be used and how should it be applied?


Identifying External Obsolescence

There are a number of factors that may produce external obsolescence including:

1. A change in market demand for the products or services. In such cases the value-

added wood products manufacturing operation may have lost some ability to generate

revenue and therefore the value of the plant may have gone down. For example, the

supply of low-cost plywood from overseas has increased and/or the consumption of

plywood for use in housing has dropped, causing an over-capacity situation in the

industry.

2. A change in the attractiveness of the location. Commonly referred to as locational

obsolescence, this decline in value is caused by a variety of factors that change the

attractiveness, and therefore value, of a location. For example, the closure of an

existing highway may adversely affect the value of properties in a particular locality.

3. A change in government restrictions or regulations. For example, a new regulation that

means additional environmental remediation measures have to be taken at value-

added wood products manufacturing plants may result in a requirement to spend

money and a corresponding reduction in value.

4. Physical site restrictions. The demand for a service may be such that expansion is

desired. However, due to zoning or physical restrictions, this may not be possible on

the existing site. Anything from the unfulfilled need for more parking spaces to a

desired building expansion may cause this form of external depreciation.

5. A decline in general economic conditions. A recession can cause a drastic and long-

term fall in the demand for value-added wood products. This may result in creating

oversupply situations for value-added wood products and a corresponding drop in

demand and value for the properties used for producing such items.

6. Changes in the value of the Canadian dollar. Value-added wood products

manufacturing plants which export most of their products can be affected by

significant changes in the value of the dollar which may impact on the value of the

business and, possibly, on the value of properties used by those businesses.

7. Changes in the availability of services. Municipal restrictions on waste disposal, the

closing of a rail spur line, and other similar changes in services can cause a decline in

value due to this type of external obsolescence factor.


In the case of more specialized properties such as value-added wood products manufacturing

plants, it may be necessary to undertake a review of information obtained from the property

owner and the industry which will help to:

• Determine past, current and expected production levels.

• Establish capacity utilization.

• Research the industry, establish the profitability of the industry.

More detailed factors to consider in this connection are shown in Part 2 of this Methodology

Guide. Many of these factors will be included in MPAC’s Market Valuation Report which forms

part of MPAC’s Level 2 Disclosure.

If it is necessary to seek this type of information, assistance from the property owner or

operations manager is helpful. Other resources include:

• trade publications

• Statistics Canada data

• industry studies

• reports on similar properties

The objective is to determine whether the cost analysis should incorporate an external

obsolescence allowance and/or whether a replacement cost based on a modern facility is

warranted.

It follows that, in order to identify the presence of external obsolescence, the assessor needs

to study:

changes in product demand

changes in the financial performance of companies in the industry

changes in competition – locational factors

It is also important to gain some understanding of the reason for these changes, (e.g., general

economic recession; development of a more efficient manufacturing process elsewhere; etc.)

in order to understand the nature (extent and longevity) of the obsolescence condition.


The value-added wood products manufacturing industry is particularly susceptible to changes

in consumer tastes which may have an impact on the value of these plants, particularly if they

are not flexible enough to be able to change their operations to match changes in demand for

their products.

To establish external obsolescence, the assessor has to be satisfied that the causes for any

reductions in revenue and profits stem from factors outside the control of the property owner

or operator, e.g., general economic recession, or increased competition. Poor business

performance does not always imply obsolescence. There are a number of reasons why

particular companies may experience reduced revenue and/or profit apart from the impact of

external factors.

4. Quantifying Depreciation

Depreciation in total is the reduction in value of the existing improvements in comparison

with costs new. There are various aspects of depreciation:

“Loss in value of an object, relative to its replacement cost, reproduction cost, or

original cost, whatever the cause of the loss in value. Depreciation is sometimes

subdivided into three types: physical deterioration (wear and tear), functional

obsolescence (sub-optimal design in light of current technologies or tastes), and

economic obsolescence (poor location or radically diminished demand for the

product).”

[Property Appraisal and Assessment Administration, IAAO, 1990, page 641]

There are a number of ways to quantify depreciation including:

Market extraction - determining the typical global amount of depreciation from costs

new based on the evidence of properties that have sold.

Age-life approach - where total depreciation is estimated (usually on a straight line

basis) by determining the current life of the property as a ratio of the expected total

economic life.

Both these methods are based on the demonstrated sales values of similar properties.

Knowing how long a property is expected to last (economic life), and its value at the end and

other points of that life, enables the prediction of value from cost new to a point in its life.

These two methods are reasonably simplistic in approach and work well with groups of

properties that have common characteristics under typical conditions. They rely on the


appropriate sales and life data being available. Examples of how they may be applied are

shown in step 6 where they are used for checking the quantum of depreciation deducted

rather than as a method of calculating the amount to be deducted.

As already indicated, there are very few, if any, sales of large value-added wood products

manufacturing plants that might allow either of the above approaches to be used. For that

reason, a different approach - the breakdown approach - should be used (see below).

Breakdown Approach

The breakdown approach involves each component of depreciation being identified and

quantified separately. The breakdown approach is the most comprehensive and detailed way

to measure depreciation as it segregates total depreciation into the three individual parts, i.e.,

physical deterioration, functional obsolescence and economic obsolescence. It is also

cumulative with each step building on the results of the previous step until all forms of

depreciation have been considered. In this way the assessor can gain a better understanding

of the impact of all forms of depreciation on the value-added wood products manufacturing

plant that is being valued.

The steps in the breakdown approach are as follows:

Estimate Replacement Cost New - adjust reproduction costs new for excess capital

costs, over-building and excess space; this produces replacement cost new.

Estimate Physical Deterioration - apply depreciation rates from ACS then, if

appropriate, calculate the effects of any deferred maintenance and costs to cure to

further revise the replacement cost new.

Estimate Functional Obsolescence - calculate and apply functional obsolescence.

Estimate External Obsolescence - estimate and apply external obsolescence.

Determine the Depreciated Value - of buildings and other improvements.

As already indicated, the breakdown approach has the advantage of being able to look at, and

quantify, the impact of each aspect of depreciation affecting the property. This allows for the

quantification of depreciation in abnormal or non-typical situations.

Quantifying the various components of depreciation in the breakdown approach is explained

below.


Replacement Cost Analysis

Replacing Construction Materials during Cost New Analysis

There are a number of techniques and materials that can be used to construct the type of large

industrial buildings used in value-added wood products manufacturing plants. There may be a

functional reason why one material was chosen over another for the existing property. For

example, operations that run fork-lift trucks tend to be built with concrete block or concrete

walls to a height of at least 6 feet. While metal siding is generally a less expensive building

material, fork-lift trucks tend to put holes in those types of walls. In such instances, the more

expensive concrete building material is there for a reason and would not be replaced by a less

expensive option.

On the other hand, some properties may be over-built and would not be rebuilt as they stand.

For example, a value-added wood products manufacturing plant may have once required

extensive materials storage facilities on-site. A move to “just in time” operations may have

rendered such storage facilities no longer necessary and therefore they may not add value to

the property.

It should be noted that, although replacing existing construction materials might be

considered in connection with replacement cost new, this approach should not be taken at

the earlier stage of the valuation when considering reproduction cost new.

The following is a list of some of the issues that should be considered by the assessor when

evaluating construction materials, techniques and costs.

Layout of Buildings

A value-added wood products manufacturing operation that has evolved and expanded over

time may have a tendency to have disjointed production flows. Evaluating the functionality of

such a plant may involve recognizing any inefficiencies caused by the layout of the existing

buildings. The assessor should consult the owner or operator of the value-added wood

products manufacturing plant to obtain reliable information about this issue.

Used and Unused Areas

During the property inspection, the assessor should have been able to identify any areas of

buildings that are not being used. The assessor should have queried the reason why the space

is unused with the owner or operator of the value-added wood products manufacturing plant

and reached a conclusion whether or not the lack of use is likely to be permanent.


Another issue may be any excess height and the unused vertical space in a building. Before

the existence of excess height can be determined, the assessor should address the question of

why the structure was constructed to its current height and determine if that height or the

“extra” area adds value to the property. It should be noted that the critical factor for most large

specialized industrial properties is not the actual height of the building but the clear height, i.e.,

the distance from the floor to the bottom of the roof trusses. However, the assessor also

needs to consider whether any unused space, height, land, etc., only relates to the way in

which the current operator uses the property and whether another operator within the value-

added wood products manufacturing industry might fully utilize the space available.

Determining whether there is excess land within the site may be more difficult, but it is usually

possible to identify the potential for excess land. This may need to be reflected when the

value of the land is being considered later.

Modern Replacement Plant

Designing and costing a modern replacement value-added wood products manufacturing

plant addresses the “buy existing or build new” issue facing a potential purchaser of the

subject property. In other words, the decision whether to:

Build a new value-added wood products manufacturing plant that satisfies all the

functional needs and expectations, or

Purchase an older existing value-added wood products manufacturing plant with less

functionality and lower utility, but at a lower price.

Choice Facing Purchaser - Utility / Price Scale

Utility

$0

$ P

rice

Older, Larger Less

Efficient Property

New Modern Plant


A reproduction cost new determines the cost to replicate the existing improvements with a

new value-added wood products manufacturing plant of similar functionality.

The “model replacement” plant approach may be used in situations where the existing

improvements are significantly over-built in relation to current needs.

The model or "green field" approach starts by replicating all the functions and utility present in

the existing property, while taking advantage of the advances and technological changes in the

field to produce a fully functioning, modern, efficient value-added wood products

manufacturing facility. The analysis should be considered on the basis of a realistic evaluation

of the requirements and capabilities of the existing property, and what would be required to

replace it. Constraints such as current location, site size and zoning by-laws should be taken

into consideration.

If completed properly, the difference between the cost new of this modern facility and the cost

new of the existing property represents the excess capital costs - or functional obsolescence -

due to the overbuilt nature of the existing property.

By comparing the subject property to a modern facility, it becomes possible to identify and

evaluate the following aspects of the existing property:

functionality

excess operating costs

excess construction costs

A replacement model approach takes a significant amount of design expertise to provide

realistic detail about the improvements sufficient to enable the completion of a cost analysis

and to ensure that all the necessary functionality is present.

The assessor should take into account the views of the owner or operator of the value-added

wood products manufacturing plant when considering whether or not the existing facility

would be replaced by a significantly different design and, if so, where information about that

type of facility (and the cost to build it) may be found.

Replacement of Building Components

In addition to the overall replacement concept, there will be situations when only part of the

property would be replaced. Under this approach, it is possible to go through the value-added

wood products manufacturing plant, component by component, and make evaluations as to


the utility of each element. In this instance, the deduction for depreciation due to super-

adequacies would be the summation of the individual calculations.

For example, a value-added wood products manufacturing plant may have a warehouse that

is only 50% used because the operation now uses “just in time” supplies so no longer needs as

much storage space as it had when originally constructed. In such instances, the analysis of

cost new would be the same as normal apart from the deletion of the old warehouse section

and the addition of a warehouse that is 50% smaller (assuming that the “surplus” space in the

existing property is permanent and there is no alternative use for it).

Quantifying Depreciation Due to Age and Condition

As already indicated, the ACS system has built-in tables that account for the typical amount of

depreciation due to age. Under typical conditions, each building component (office area,

receiving area, processing area, storage area, etc.,) is assigned a depreciation rate (% Good)

according to the effective build date and the life expectancy.

The assessor should refer to the ACS example (Table 1) to see how the depreciation rate

(% Good) is used.

Quantifying Functional Obsolescence

In broad terms, the quantification of incurable physical deterioration and incurable functional

obsolescence can be found by deducting replacement cost new from reproduction cost new.

However, it is helpful to consider the issues in more detail as set out below.

There are different methods used to quantify the various aspects of obsolescence. Difficulties

in quantifying obsolescence arise where there is no established market place which can be used

to form comparative judgments either in terms of income potential, market sales values or

efficiency benchmarks. In these situations, the losses in value due to obsolescence can

generally be identified, but the estimation of the extent of the impact on value is sometimes

more difficult.

Another way to consider physical depreciation and functional obsolescence is to examine the

excess operating costs that might be incurred from operating a sub-optimal value-added wood

products manufacturing plant.

Capitalization of Excess Operating Costs Analysis

A prudent purchaser will take into account all cash outlays (expenses) when considering the

price of a property. If the property creates inefficiencies or increased production costs due to


its layout or building services, then the purchaser will factor these costs into a purchase

decision.

Excess operating costs are those costs that arise as a result of the inefficiencies inherent in the

real estate used by the existing value-added wood products manufacturing operation in

comparison to a more efficient operation. They negatively impact the value and can be

measured by capitalizing the amount of excess costs. Excess operating costs will affect value

even after the replacement model approach is considered.

For example, an office building at a value-added wood products manufacturing plant may

have an old HVAC system that results in an additional $25,000 per annum to the operating cost

in comparison with a more efficient, modern system. This extra cost makes the subject property

less attractive and therefore less valuable than an office building with an efficient system. This

additional annual cost can be capitalized and the capital sum deducted as part of the

functional obsolescence calculation.

There is a risk of confusion when using replacement costs and it is important that the

valuation approach is consistent. If a modern replacement value-added wood products

manufacturing plant is being considered for the purposes of calculating the amount of

depreciation impacting the existing plant, the replacement office building will be assumed to

have a modern HVAC system. However, that does not alter the fact that the existing office

building at the value-added wood products manufacturing plant being valued has a less

efficient HVAC system and the excess operating costs associated with the HVAC system at the

existing plant will still therefore need to be deducted.

What Constitutes Excess Operating Costs?

Any excess operating costs or inefficiencies attributable to the real estate (improvements or

site) should be considered as a form of depreciation. Costs that relate to the business (labour,

management, machinery, etc.), while they may have long-term impacts on the economic

viability of the property, should not be considered as part of functional obsolescence in the

property valuation process.

Typically, the following factors give rise to excess operating costs:

Inefficient heating, air conditioning and/or ventilation systems.

Poor property design or layout causing excess materials handling costs, including extra

costs for personnel and equipment.


Poor property design and/or excess space causing extra maintenance and other

operating costs.

Capitalizing Excess Operating Costs

To complete the analysis of the impact of excess operating costs requires knowledge of three

elements:

1. The remaining economic life of the property, i.e., how long these excess costs are

going to continue to be incurred.

2. An appropriate capitalization rate (generally the cost of funds for that industry).

3. The effective corporate tax rate and whether the property is expected to make

profits.

The remaining economic life of the property impacts on how long these excess operating costs

are expected to last. The capitalization rate converts the annual cost into a present value and

the annual costs are reduced by the effective tax rate because these extra costs reduce profit

and, as a result, the company will pay less tax.

There are several ways to rationalize a capitalization rate. Some inference can be drawn from

the capitalization rates found in sales transactions in the market for other types of investment

such as long-term interest rates for various types of financial instruments; however, a more

rational approach is to develop the cost of funds for a typical purchaser (see example below).

Impact of Excess Operating Costs

When studies done during the depreciation identification stage result in confirmation of

excess operating costs, their impact is estimated by capitalizing the future costs into a present

value. For example, a value-added wood products manufacturing plant is overbuilt and, as a

result, it has two extra employees to perform maintenance work with a total annual cost of

$150,000 per year. The owner of a new value-added wood products manufacturing plant does

not have this cost. Noting that the economic life of the value-added wood products

manufacturing plant is expected to last another 5 years, and that the current corporate tax

rate is 25%, the impact on value of the excess operating costs at $150,000 per annum may be

calculated as shown in Table 4 below:


Table 4

Element Annual Cost Tax

adjustment

Period

(years)

Factor at 8% Functional

obsolescence

Additional

cost relating

to excess

area

$150,000 -25% 5 3.9927 $449,180

Rounded $449,200

Note: Rates are for illustrative purposes only.

To explain how the above table works, it has been determined that there are excess operating

costs as a result of additional employees related to the value-added wood products

manufacturing plant which amount to $150,000 in extra expenses per annum. What needs to

be determined is what the discount to the overall value this additional expense would have,

since the facility was measured on the cost method and we cannot simply deduct it from an

income stream.

If the resulting excess costs are considered to be an income stream, it would be necessary to

determine the after-tax cost to the company for hiring those additional workers. If the pre-tax

expense is $150,000, and the corporate tax rate (which varies by jurisdiction and company

type) is 25%, then the after-tax cost to the company would be (1-.25)*150,000 = $112,500.

This is, effectively, the annual amount which an owner would have to pay to maintain an

older, inefficient facility in comparison with a more modern facility.

It is then necessary to consider what discount a potential purchaser looking to buy the facility

would attribute to this additional expense. A purchaser would effectively reduce the purchase

price by the present value of the future outflows of cash; it can be calculated like an annuity.

In calculating the present value, two items have to be considered along with the cash flow

amount; the life of the asset (how many periods to assume the payment needs to be made

for) and the discount rate. The economic life of the facility/asset has been determined to be 5

years, so it is necessary to expect a purchaser to have to pay out 5 additional expense

payments. The discount rate has been reviewed by analysis of interest rates, bond rates and

sales of similar assets and has been set at 8%.


There are a number of places to find the factor which is used to multiply the cash flow

payment in order to determine the present value. This includes present value tables, excel

functions and/or scientific calculators. When the present value tables using 5 years and 8%

discount rate is used, a factor of 3.9927 is determined. This factor is multiplied by $112,500 to

find that the present value of 5 years of expected cash outflows would be $449,180

(rounded).

It will be seen from Table 4 that the impact on the current value as a result of excessive

building area and two extra employees at $150,000 (salary and benefits) has been taken to be

$449,200.

As a dollar amount deduction, it becomes important at what point in the process this

functional obsolescence depreciation is applied. When a potential purchaser compares two

properties with similar functionality, one with excess operating costs and one without, the

impact of $449,200 comes after the physical deterioration and replacement issues have been

considered, but before any external obsolescence impacts which are beyond the control of

the property owner, and which may or may not change in the future. Therefore, it is at that

stage in the valuation that an adjustment needs to be made by the assessor for this factor.

Functional Obsolescence when no Excess Cost Information is Available

As is often the case, the detailed cost information needed to calculate the impact of functional

obsolescence may not be readily available. In these situations, the functional obsolescence

should be recognized by the assessor and a judgment made as to the percentage impact it is

likely to have on the purchase price of the property. This type of deduction can be applied as a

percentage deduction on a component by component basis, or by a property-wide deduction.

Quantifying External Obsolescence

“External obsolescence is a loss in value caused by factors outside the property. It is

often incurable. External obsolescence can either be temporary (e.g., an oversupplied

market) or permanent (e.g., proximity to an environmental disaster). External factors

frequently affect both the land and building components of a property’s value. External

obsolescence usually carries a market-wide effect and influences a whole class of

properties, rather than just a single property. External obsolescence may only affect the

subject property when its cause is location - e.g., proximity to negative environmental

factors or the absence of zoning and land use controls.”

[The Appraisal of Real Estate, 12th edition, Appraisal Institute, page 412]


The key issues producing external obsolescence are:

Significant change in demand for product.

Plant not working to capacity.

Costs of production no longer competitive.

To understand external obsolescence, the assessor needs to understand why these things

have happened and if they are happening to other producers. It is important to consider

whether the external conditions affecting the property would normally translate into a

physical change in the property (e.g., size, configuration, etc.). Alternatively, if property

changes do not address the issue, what is the loss in value as a result of this type of

obsolescence?

As with the application of the other forms of depreciation, external obsolescence is usually

expressed as a percentage of cost new and deducted from the replacement cost value less

physical and functional obsolescence.

Methods of Quantifying External Obsolescence

Studying changes in factors like capacity usage ratios and gross margins can assist in

quantifying this type of obsolescence, but external obsolescence tends to be industry and

property specific in nature. Establishing market (i.e., current) value is best achieved by the

assessor assuming the role of a potential purchaser, i.e., a “knowledgeable” purchaser. For

properties with a specific highest and best use such as value-added wood products

manufacturing plants, this study will involve research into the industry and recent changes in

that industry, a view to the future of that industry, and specific knowledge about the location

and other “local” factors affecting the specific property.

Part 2 of this Methodology Guide contains more detailed information about the factors to

consider in connection with ascertaining whether there is external obsolescence and, if so,

how it may be quantified. It should be noted that MPAC produce Market Valuation Reports for

each reassessment as part of its Level 2 Disclosure process; these reports will assist the

assessor in reaching a conclusion about whether or not an adjustment needs to be made for

external obsolescence and, if so, what the quantum of that adjustment should be.

Where the presence of external obsolescence has been identified, the impact can be

quantified using the following steps:


1. Complete a detailed study of the industry - in this case, the value-added wood

products manufacturing industry - and the economic factors that are affecting it and

establish the degree (or range) of the changes taking place in the industry.

2. With the assistance of the owner or operator, analyze the performance of the value-

added wood products manufacturing plant being valued (i.e., units produced, profits

or losses, cost per unit, etc.) and compare it to the industry standards. This can

identify whether there are more issues concerning the subject property (e.g.,

operating cost issues, locational issues, etc.) than at other similar value-added wood

products manufacturing plants.

The degree of value loss should reflect the magnitude of the changes in the property.

Quantifying external obsolescence in respect of the real estate is sometimes challenging

because the conditions invariably also impact on the business value of the operation.

The three traditional methods of quantifying external obsolescence are:

1. Establish total depreciation using market-extraction or other approaches to value

then use a “residual” approach to determine how much obsolescence remains after

quantification of the other forms of depreciation.

2. By considering stock or other financial measures, determine the magnitude of the

loss for the business due to external obsolescence, then “translate” the finding to

apply to the real estate component.

3. Find comparative value data for similar properties not affected by the obsolescence

and determine the differences in value. This could also be an analysis of “paired

sales” data where a property was sold before and after the obsolescence condition,

or paired income data where lease rates have changed before and after the

obsolescence condition. Where valuation dates are in the past, such “pairing” of data

could be forward or backward looking.

More sophisticated approaches may involve a “utilization analysis,” a “return on capital

analysis,” an “equity to book ratio analysis,” and/or a “gross margin analysis”; however, these

approaches usually require specialist expertise and the assessor may not be expected to

undertake these forms of analysis without expert assistance.

An attempt should be made to use one or more methods to quantify the obsolescence. If,

because of the lack of comparable sales/value data, this is not possible, the assessor should

make a judgment and attempt to support the rationalization. The important point is that the


presence of external obsolescence, assuming it exists, has been properly identified and that a

reasonable allowance needs to be made for this factor.

The appropriate adjustment for external obsolescence in respect of value-added wood

products manufacturing plants, along with an explanation of the rationale for the guidance,

will be contained in the Market Valuation Report prepared by MPAC for the value-added

wood products manufacturing industry as part of its Level 2 Disclosure process.

An example of the adjustment that might be made for external obsolescence, and the reasons

for it, is shown in Box 1 below. The figures used are illustrative only and do not relate to any

particular industry.

Box 1

To determine if economic obsolescence is present, the assessor should review the

economic indices or ratios of the subject property and the industry in which it

competes as of the effective date of value.

The review should involve a comparison of the economic indices and ratios as of

the effective date against those realized during a period when the subject

property and the industry in which it competes were performing as intended.

For publicly traded companies, the economic indices and ratios realized in the

past ten years are readily available for review. The only way to obtain economic

information that is applicable to the subject property is via the owner of the

subject property.

Example

Year Economic Ratio

2006 24

2007 22

2008 20

2009 20


2010 23

2011 19

2012 18

2013 15

2014 17

2015 17

The observations from the data contained in the table are as follows:

The peak ratio in the past 10 years is 24.

The mean ratio of the past 10 years is 19.5.

The mean ratio of the best three years is 23.

The ratio as of the effective date (i.e., January 1, 2016) is 17.

The assessor must compare the ratio realized as of the effective date (i.e., 17) to

the ratio(s) realized when the industry or subject property was performing as

intended.

If the assessor concludes that the mean ratio of the best three years (i.e., 23)

reflects an era when the industry or subject property was performing as intended

the allotment for economic obsolescence would be:

EO = 3 Year Mean – Ratio as of Effective Date

3 Year Mean

EO = 23 – 17

23


EO = 6

23

EO = 0.26 or 26 percent

The assessor should make best efforts to analyze many economic indices and

ratios to obtain multiple indicators of economic obsolescence. Each of the

indicators should be considered by the assessor before reaching a conclusion as

to what the appropriate allotment for economic obsolescence should be.

Judgment

In some instances, obsolescence is easily recognized, but is difficult to quantify. Given a

thorough understanding of the property, the nature and condition of its business, the nature

and condition of the industry, sometimes the only available method of quantifying the

obsolescence is through making a judgment. This judgment should be made with respect to

current competitive standards and/or typical operating conditions for that type of property.

However, the determination of obsolescence should be based on facts and as many

observations from the market as possible.

Once all forms of depreciation have been identified, quantified and deducted from reproduction

cost new, the end result is the current value of the improvements determined through the use of

the cost approach.

Adding in the net values of other improvements such as vehicle parking and the value of the land

(see step 5 below) produces an estimate of value using the cost approach.

Table 5 provides an example of a typical ACS cost approach valuation summary (including the land

value).


Table 5

5. Value the Land

At this stage of the valuation, the value of the land on which the value-added wood products

manufacturing plant has been developed needs to be considered. Land is valued using the

market sales comparison process.

It is recognized that there may be very few sales of land to be used for value-added wood

products manufacturing plants in the immediate locality of the property to be valued. For this

reason, the assessor may need to look across a wider geographical area and/or look for sales

of sites to be used for other large manufacturing plants.

Land Sales Analysis Process

The assessor should collect data on all land sales within the relevant time period in each

region, tabulated by property type and zoning. Sales data collected includes:

property address and legal description

size of the lot

infringements (wetlands, etc.)

type of services to the site


sales price

date of transfer

instrument number

name and address of vendor and purchaser

interest(s) transferred

financing conditions

zoning information

Sales data should also include improved properties that were bought and subsequently

demolished in favour of a new development.

It is necessary to inspect the properties to determine if the sale was of a vacant parcel. Also,

the nature of any new development on properties that have been re-developed should be

noted.

Land Sales Analysis

More than any other factor, the type and quality of information gathered governs the quality

of the final analysis.

Sales data on properties most similar to the subject property in terms of size, zoning, location

and time of sale will have the most relevance to the valuation of land relating to the subject

property.

Land sales should be verified with the vendor and purchaser to ensure that they are arms-

length, open market transactions and that the cash equivalent value is discerned. Ideally,

these sales should have taken place as close as possible to the date of valuation. Once

comparable sales data has been obtained, land values should be established on the basis of a

price per unit of site area.

Issues in the Valuation of Land

Some issues particular to valuation of land may arise as indicated below.


Sales Search Parameters – Location

Location is usually an important factor for value-added wood products manufacturing plants

and is likely to reflect needs in terms of sources of supply (e.g., materials, labour, etc.),

transport links, and customer base.

Principle of Consistent Use

The valuation of land is guided by the principle of consistent use, i.e., building values should

be complementary and in accordance with the underlying premise used to value the land.

Sales Search Parameters

When searching for comparable land sales, the assessor should set up search criteria as

follows:

1. Properties with the same or similar zoning. When reviewing zoning for large industrial

properties such as value-added wood products manufacturing plants, the assessor

should look to the uses allowed to ensure comparability.

2. Properties of similar size. If there is an insufficient number of sales for properties of

similar size, the assessor should attempt to cover a range of property sizes - some

larger and some smaller - so that the value of the subject site can be interpolated from

the data.

3. Land within the same locality. The assessor should look first to sales of sites in close

proximity to the subject. It may be necessary to expand the search area if an

insufficient number of sales are found.

4. Time of sale. Land values change over time, but given enough sales, or some paired

sales (i.e., the same property selling more than once), it is possible to determine the

change in land value over time.

Time of Sale and Size of Site

It is generally easier to adjust the sale price of land for time of sale and size of site as opposed

to location and zoning. However, if an industrial operation such as a value-added wood

products manufacturing plant requires a site of substantial size, it is probably of greater

assistance to consider similarly zoned and similarly sized sites located in a larger geographic

area, rather than smaller sites located in the immediate vicinity.


Level of Services

The more services there are to a site, the higher its value, all other factors being equal.

Sometimes, land sales reflect unserviced land prices (e.g., farmland, bush, etc.). It is

challenging to establish the value of a serviced parcel when considering unserviced prices.

However, by combining the cost of servicing (sometimes available from published municipal

studies) with the unserviced price (plus time adjustment, plus developer’s profit), it is possible

to arrive at reasonable land value conclusions.

Land Value - Conclusion

The assessor will need to make judgements about the value of the land which has been

developed for use as a value-added wood products manufacturing plant based on whatever

sales there may have been for broadly similar use.

Inevitably, the more specialized the use, the greater care has to be taken in the collection of

data and the valuation of land.

Finalize Current Value

The final stage in this part of the process is to add the value of the land to the depreciated

value of the improvements determined at step 4 to arrive at the overall current value of the

value-added wood products manufacturing plant as of the relevant valuation date.

6. Validate the Results

Checking the Results of the Cost Analysis

The final step in the cost approach is to review all the previous steps and ensure that the

approach taken is justifiable, consistent and accurate.

In particular, the results of the breakdown approach to depreciation need to be checked for

two issues:

1. That the value derived relates to the expected value of the property if it were to sell on

the valuation date.

2. That the depreciation applied does not “double-count” the impact on value and, as a

result, overstate the overall depreciation.

There are a number of steps that can be undertaken to confirm that the estimate of value

completed by the cost approach is a “market” (i.e., current) value.


1. Complete an estimate of value using a market sales comparison approach.

2. Complete an estimate of value using an income approach.

3. Complete an age-life study.

4. Complete a market extraction depreciation study.

5. Where sales and other information is limited, check the value against the available sales information.

All these approaches require at least some information on real estate transactions (sales, rents, etc.). In markets such as large value-added wood products manufacturing plants, the lack of such information makes this checking process challenging.

The assessor should look carefully to see if there are any transactions that can be found which may be of assistance in applying these validations.

The most straightforward forms of depreciation analysis that can be used to check the overall level of depreciation applied to derive the value of the improvements at value-added wood products manufacturing plants are the “age-life approach” and the “market extraction method.”

Age-Life Approach

This approach seeks to establish the typical remaining value of the property at the end of its economic life (if any). For example, if a property sold for 5% of its value at the end of its 50 year economic life, then the total depreciation at the end of its life would be 95% and the depreciation to be applied to a 10 year old structure would be:

95% x 10 / 50 = 19.0% depreciation

The Appraisal of Real Estate (Third Canadian Edition) suggests that either reproduction costs or replacement cost could be used with the proviso that the basis for analysis should be internally consistent throughout the valuation.

The accuracy of the age-life methods rests on four conditions:

1. That the expected total economic life of the property can be established.

2. That the effective age and the expected remaining life of the property can be determined.


3. That a “straight-line” depreciation rate best reflects the depreciation occurring at the

property.

4. That some further accommodations be made when the property is suffering from

abnormal conditions.

Several issues arise in the application of the age-life approach:

The calculation of expected life can be completed on the basis of chronological age or

effective age, but not both. Effective age is a more refined measure, but it requires

that the assessor know all the effective ages of the properties studied to create a life

expectancy benchmark.

The simple ratio adopted by the age-life approach describes a straight-line

depreciation curve which is not a very sophisticated application of depreciation.

The age-life method does not do well in predicting depreciation during abnormal

economic times. The prediction of overall depreciation would be the same by using

this method whether there was a recession or not.

The age-life approach does best where properties have very similar functionality and

comparable size, the effective ages are known, and there are no external obsolescence

considerations.

The process requires some adjustment if the conditions are abnormal, or if the property itself

is suffering from abnormal depreciation impacts.

The point of the analysis here is to determine whether the depreciation applied in total as a

result of the breakdown analysis agrees with the factor arising from the age-life analysis. If

there is a large discrepancy, then some further analysis of depreciation should be considered.

A simple example of how the age-life method may be used is shown in Table 6 below:

Table 6

Line Number Subject Property Details Formula Amounts

1 Total economic life of

improvements

55 years


2 Effective age of improvements 20 years

3 Age-life ratio Line 2/Line 1 36%

4 Cost new of improvements $5,400,000

5 Depreciation amount Line 4 x Line 3 $1,944,000

6 Depreciated value of

improvements

Line 4 – Line 5 $3,456,000

In this example, the depreciated value of the improvements resulting from the application of

the breakdown method applied at step 4 should be compared with the figure of $3,456,000

derived from the age-life approach to see if it is broadly similar. If it is not, the assessor will

need to review the calculation of depreciation to see if it contains any errors.

Market Extraction Method

An alternative approach to the calculation of overall depreciation is the market extraction

method. Like the age-life approach, the method does not differentiate between the various

types of depreciation, but uses available market sales data to establish the difference

between costs new and market value.

The basis of market extraction is a study of the overall depreciation for a property type as set

by the market. Knowing the value of a property as new, and the value and the age of the

property when it sells, provides an indication of the overall depreciation.

The process requires sales of similar properties and establishes the improvement value at sale

by subtracting the land value from the sale price. The difference between the cost new of the

improvements (either replacement or reproduction) and the sale price is the total amount of

depreciation attributable to improvements. If the sales take place at different dates, then the

typical global amount of depreciation per year can be calculated and applied to the subject.

A simple example of how the market extraction analysis works is shown in Table 7 below.


Table 7

Sale 1 Sale 2 Sale 3

Sale price $1,900,000 $2,370,000 $1,880,000

Less land value -$1,234,000 -$1,409,000 -$934,000

Market value of

improvements

666,001 961,002 946,003

Cost (new) of

improvements

$1,340,000 $1,658,000 $1,145,000

Total depreciation ($) $637,200 $697,000 $199,000

Total depreciation

(%)

50.2% 42.0% 17.4%

Age (years) 33 27 12

Depreciation per year 1.52% 1.55% 1.45%

From this study, the market extraction method concludes that the total amount of

depreciation should be 1.51% per year. Given a 10 year old building at a value-added wood

products manufacturing plant, the total depreciation calculated from the market extraction

method should be 15.1%.

By combining a number of such sales information for similar properties it becomes possible to

build up a picture of the expected depreciation at a given age.

As a general approach, the market extraction method suffers the same kind of benchmarking

issues as the age-life approach. With enough sales, it may be possible to develop overall

depreciation curves for various sizes and types of large industrial properties. But the

application works best when comparable sales data of similar properties is available, and the

results can be adjusted according to differences in the properties.


As already indicated, there may not be sufficient evidence of transactions concerning value-

added wood products manufacturing plants that will enable the assessor to use this method.

However, whatever evidence is available should be examined carefully to see whether this

type of analysis can be undertaken.

Sales Benchmarks

Another way to check a cost approach result is to find some sales of like properties and

determine if the sales results of these properties show the same kind of results as the cost

analysis on the subject, e.g., a similar $ per square foot results. This is different from a “full-

blown” market sales comparison analysis where the sales values are adjusted to produce a

value conclusion for the subject.

This approach may be used where there is limited sales data or where the comparability

between properties requires large adjustments. It is not designed to provide a valuation

answer, but rather provide a point of comparison to allow the assessor to determine the cost

approach result for a value-added wood products manufacturing plant is in line with the

market evidence for other similar large industrial properties.

Comparison with other Value-Added Wood Products Manufacturing Plants

Having completed the valuation and carried out the validation checks outlined above, the

assessor should compare the result with the current values of other value-added wood

products manufacturing plants within Ontario.

If the result of the valuation process for the particular value-added wood products

manufacturing plant being valued appears to be out of line with the current values of other

similar value-added wood products manufacturing plants, the assessor should investigate the

differences to see whether they indicate that an error may have been made at any of the

earlier steps in the valuation.

Ideally, the outcome of the validation and comparison checks will show that the current value

of the subject value-added wood products manufacturing plant derived from the cost

approach is correct.

For a simple example of what the completed valuation may look like, along with a reminder of

the key steps in the valuation process, see Table 8 below.


Table 8

Reproduction cost new $1,400,000

Deduct excess capital costs (cost of overbuilt areas) -$110,000

Replacement cost new $1,290,000

Deduct cost-to-cure deferred maintenance $30,000

Sub-total $1,260,000

Deduct physical depreciation - 30% -$378,000

Replacement cost new less depreciation (RCNLD) $882,000

Deduct additional functional obsolescence -$72,000

Sub-total $810,000

Deduct external obsolescence - 10% -$81,000

Depreciated value of improvements $739,000

Add land value $486,000

Market value estimate $1,225,000


Appendices

Appendix A - List of Properties Covered by this Methodology Guide

Company Name Location Address 1 Location City Roll Number Total Floor Area Closed/Idle

Weyerhaeuser Company Limited 1000 Jones Rd Kenora 6016-140-004-11302 490,009

Panolam Industries Ltd. 61 Domtar Rd Huntsville 4442-040-019-09300 423,686

Danzer 402725 Grey Road 4 Durham 4205-280-003-04600 408,589

Temple Pembroke Inc 777 Fibreboard Dr Pembroke 4766-062-040-00400 387,735

Ainsworth Engineered Canada Lp Nighswander Rd Barwick 5924-020-001-02700 349,323

Gp North Woods Lp 327022 Hwy 11 N Englehart 5452-000-001-01300 341,038

Levesque Plywood Limited 201 Edward Street Hearst 5676-010-003-18800 291,497

Rtk Wp Canada Ulc Highway 101 Province of Ontario 5799-162-000-00600 291,292

Flakeboard (Ssm) Company 657 Base Line Sault Ste. Marie 5761-060-001-05500 290,347

1560177 Ontario Inc 79 Y Rd Bancroft 1290-278-015-05800 267,603 Yes

Kenogami Industries Inc 102 Katamaki Road Greenstone 5876-710-001-14200 259,465 Yes

Alexandria Moulding Inc. 20352 Power Dam Rd Alexandria 0111-018-000-61005 240,710

Satin Finish Hardwood Flooring 15 Fenmar Dr North York 1908-013-300-00700 211,259

Rtk Wp2 Canada Ulc 106 Goodwin St Atikokan 5901-000-008-17501 182,169

Tembec Fpg-Hearst Inc. 67 Fontaine Dr Hearst 5676-010-006-08169 157,185

True North Harwood Plywood 4 Boisvert Cres Cochrane 5639-010-005-27500 144,436 Yes

Barco Materials Handling Ltd. 24 Kerr Cres Puslinch 2301-000-006-11640 123,654

Columbia Forest Products Hwy 17 E Rutherglen 4822-000-001-41701 104,985 Yes

Anthony-Domtar Inc 1195 Peoples Rd Sault Ste. Marie 5761-050-043-08701 94,659

Niska North 303 Martel Road Province of Ontario 5289-570-006-00950 91,960 Yes

Cutler Group Inc. 1265 Aerowood Dr Mississauga 2105-050-116-01610 88,228

Olon Industries Inc. 42 Armstrong Ave Georgetown 2415-020-003-03700 81,311


Rockland Flooring Ltd. 139 Elm St West Lorne 3434-036-002-39200 77,147

Weston Forest Products 7600 Torbram Rd Mississauga 2105-050-115-16300 76,076

Sault Ste Marie Economic Dev 16 Wood Park Crt Sault Ste. Marie 5761-060-001-00620 75,959

Kirkland Lake Engineered Wood Grenfell Kirkland Lake 5480-100-000-01900 75,192 Yes

Tekwood Inc. 607 Canarctic Dr North York 1908-033-350-02000 68,410

Lake Scugog Lumber & Coal Co 11 Vanedward Dr Port Perry 1820-010-008-08710 62,857

Watford Roof Truss Ltd. 330 Front St Watford 3841-042-001-02500 61,107

Tamarack Lumber Inc. 3269 North Service Rd Burlington 2402-090-903-02800 52,960

Interior Manufacturing Group 974 Lakeshore Rd E Mississauga 2105-070-156-14800 48,623

K.D. Quality Pellets 999562 Highway 11 New Liskeard 5426-000-001-17503 26,980

Northern Pressure Treated Wood Ltd Gauthier MC L27334 Kirkland Lake 5466-000-002-32100 18,705

Note: Inventory listing is effective as of April 8, 2015. Listings continue to be reviewed and are subject to change throughout the consultation process.


Appendix B – Glossary of Terms

These definitions are from a variety of sources including Property Appraisal and Assessment

Administration, Joseph Eckert, ed. IAAO and The Appraisal of Real Estate, Appraisal Institute,

12th Edition.

Accrued

depreciation

The amount of depreciation from any and all sources that affects

the value of the property in question.

Actual Age Sometimes called “historical age” or “chronological age.” It is the

number of years that has elapsed since building construction was

completed.

Age/life method A method of estimating accrued depreciation founded on the

premise that, in the aggregate, a neat mathematical function can

be used to infer accrued depreciation from the age of a property

and its economic life.

Approaches to

value

One or more of three approaches to value, namely (a) cost (b)

sales comparison (c) income capitalization. The approaches

employed will allow the assessor to determine the value of the

property.

Assessment equity The degree to which assessments bear a consistent relationship to

market value.

Assessed value Assessed value applies in ad valorem taxation and refers to the

value of the property according to the tax rolls.

Breakdown

method

A method for estimating total depreciation by specifying the

amount of each kind of depreciation, often for each major building

component, (including physical, functional and external).

Chronological age The number of years elapsed since an original structure was built.

Synonymous are actual age and historical age. Contrast with

effective age.


Comparables,

Comparable Sales

Recently sold properties that are similar in important respects to a

property being appraised. The sale price and the physical,

functional, and locational characteristics of each of the properties

are compared to the property being appraised in order to arrive at

an estimate of value. By extension, the term comparables is

sometimes used to refer to properties with rent or income

patterns comparable to the property being appraised.

Cost The total dollar expenditure for an improvement (structure).

Cost Approach Value as estimated as the current cost of reproducing or replacing

the improvements (including the appropriate entrepreneurial

incentive or profit) minus the loss in value from depreciation, plus

land or site value.

Current value

assessment (CVA)

As defined in the Assessment Act section 1: Current value means,

in relation to land, the amount of money the fee simple, if

unencumbered, would realize if sold at arm’s length by a willing

seller to a willing buyer.

Deferred

maintenance

Repairs and similar improvements that normally would have been

made to a property but were not made to the property in

question, thus increasing the amount of its depreciation.

Depreciation The loss in value of an object, relative to its replacement cost,

reproduction cost, or original cost whatever the cause of the loss

in value. Depreciation is sometimes subdivided into three types:

physical deterioration (wear and tear), functional obsolescence

(sub-optimal design in light of current technologies or tastes), and

economic obsolescence (poor location or radically diminished

demand for the product).

Economic life The period of time during which a given building or other

improvement to a property is expected to contribute (positively) to

the value of the total property. This period is typically shorter than

the period during which the improvement could be left on the


property, that is, its physical life.

Economic/External

obsolescence

Loss in value to the improvements (relative to the cost of replacing

the improvements with one of equal utility) that stems from

factors external to the property.

Effective age The typical age of a structure equivalent to the one in question

with respect to its utility and condition. Knowing the effective age

of an old rehabilitated structure of a building with substantial

deferred maintenance is generally more informative than knowing

its chronological age.

Equity (1) The degree to which assessments bear a constant relationship

to market value. Measures include the coefficient of dispersion

and the coefficient of variation. (2) The net value of a property

after liens and other charges have been subtracted. See also

horizontal inequity and vertical inequity.

Fixed costs Costs of fixed resources used by a firm that do not vary with

production levels and cannot be changed in the short run.

Functional

obsolescence

A flaw in the structure, materials or design that diminishes the

function, utility and value of the improvement.

Functional utility The ability of the property or building to be useful and to perform

the function for which it is intended according to current market

tastes and standards, the efficiency of building’s use in terms of

architectural style, design and layout, traffic patterns and size and

type of buildings.

Highest and Best

Use

The reasonably probable and legal use of vacant land on improved

property that is physically possible, appropriately supported, and

financially feasible that results in the highest value.

Long-lived items Building components with an expected remaining economic life

that is the same as the remaining economic life of the entire

structure.


Marginal utility The change in total utility to a customer that results from a one-unit

change in the consumption level of an item.

Market extraction

method

Method of estimating depreciation which relies on the availability of

comparable sales from which depreciation can be extracted.

Market value The most probable sale price of a property in terms of money in a

competitive and open market, assuming that the buyer and seller

are acting prudently and knowledgeably, allowing sufficient time for

the sale, and assuming that the transaction is not affected by undue

pressures. See Current Value Assessment.

Obsolescence One cause of depreciation, an impairment of desirability and

usefulness caused by new inventions, changes in design, improved

processes for production or external factors that make a property

less desirable and valuable for continuing use. It may be either

functional or external.

Remaining

economic life

The number of years remaining in the economic life of a building or

other improvement as of the date of the appraisal. This period is

influenced by the attitudes of market participants and by market

reactions to competitive properties on the market.

Replacement cost The cost, including material, labour, and overhead, that would be

incurred in constructing an improvement having the same utility to

its owner as the improvement in question, without necessarily

reproducing any particular characteristic of the property.

Reproduction

costs

The cost, including material, labor, and overhead, that would be

incurred in constructing an improvement having exactly the same

characteristics as the improvements in question.

Short-lived items A building component with an expected remaining economic life

that is shorter than the remaining economic life of the entire

structure.


Special purpose

property

A limited market property with a unique physical design, special

construction materials, or a layout that restricts it utility to the use

for which it was built, also called special design property.

Documents

ASSESSMENT METHODOLOGY GUIDE - MPAC · PDF fileASSESSMENT METHODOLOGY GUIDE . ... City of Guelph Fiat Chrysler Automobiles Cushman ... alignment of the wood particles to provide strength