Vendor: S000238

Page 1 of 12

ASSEMBLY INSTRUCTIONS

CORONA 2 DOOR WARDROBE

IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING OR USING YOUR CORONA 2 DOOR

WARDROBE.

PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.

ASSEMBLY INSTRUCTIONS:

Please check contents and read instructions carefully before commencing assembly.

To avoid damages assemble the item on a soft, clean surface.

Assemble in the room of use.

HEALTH & SAFETY:

DO NOT use this item if any parts are missing, damaged or worn.

DO NOT use this item unless all fixings are secured.

Always use on a level, even surface.

It is recommended that two people handle and assemble the item.

Keep small parts out of the reach of children.

CARE & MAINTENANCE:

This product is manufactured in pine which is a wood with natural characteristics including knots, grains,

clusters or indentations.

On unpacking the item you may notice an odour due to the production process, however, this will disappear

after a period of time.

DO NOT place the item next to a radiator or direct sunlight as this item is susceptible to temperature

change. It is recommended to maintain an even room temperature with no sudden fluctuations.

For general cleaning use a duster or damp cloth (almost dry) not wet – do not use soap and water,

detergents, aerosol sprays or any polish as the use of these materials would invalidate any claims.

You may wish to re-treat the surface to maintain the original finish. This can be done using block wax (un-

perfumed). Please follow the manufacturer’s instructions carefully.

DO NOT place the item onto wet or damp flooring as staining may occur to the floor.

Periodically check all screws & fixings to ensure they are secure.

DO NOT push the item as this will damage the base.

Keep any sharp objects away from the item.

www.birlea.com

Vendor: S000238

Page 2 of 12

Vendor: S000238

Page 3 of 12

Parts List Hardware List

Part Description Qty Part Description Qty

1 Right Panel 1 A Wooden Dowel 12

2 Left Panel 1 B 14 mm Screw

50

3 Back Panel 2 C 25 mm Screw 10

4 Right Front Frame 1 D 30 mm screw

19

5 Left Front Frame 1 E 35 mm Screw

36

6 Right Door 1 F 50 mm Screw

3

7 Left Door 1 G 19 mm Bolt

2

8 Door Divider 1 H

Handle 2

9 Large Spine 1 J Hinge

6

10 Top Panel 1 K

Clip

2

11 Base/Shelf Panel 2 L

Plug

2

12 Outer Top Plinth 1 M

Hanging Rail Support

2

13 Inner Top Plinth 1 N

Stud

2

14 Bottom Front Frame 1 O Tack 40

15 Front Plinth 1 ** You will need a small mallet and a screwdriver. 16 Bottom Side Plinth 2

17 Top Side Plinth 2

18 Hanging Rail 1

19 Small Spine 1

20 Cleat 7

Vendor: S000238

Page 4 of 12

Step 1: Insert the right panel (1) into the right front frame (4) ensuring parts are fully pushed together and

correctly lined up. Place the cleats (20) between the marks shown and secure using hardware part E and a

screwdriver (not provided).

DO NOT use any power tools as this may damage the frame and will invalidate any claim.

Vendor: S000238

Page 5 of 12

Step 2: Insert the left panel (2) into the left front frame (5) ensuring parts are fully pushed together and

correctly lined up. Place the cleats (20) between the marks shown and secure using hardware part E and a

screwdriver (not provided).

DO NOT use any power tools as this may damage the frame and will invalidate any claim.

Vendor: S000238

Page 6 of 12

Step 3: Insert hardware part A using a small mallet (not provided). Secure hardware part M to the right

panel (1) and left panel (2) using hardware part B and a screwdriver (not provided).

DO NOT use any power tools as this may damage the frame and will invalidate any claim.

Step 4: Attach the base/shelf panels (11) to the left panel (2) using hardware part E and a screwdriver (not

provided). Insert the bottom front frame (14).

DO NOT use any power tools as this may damage the frame and will invalidate any claim.

Vendor: S000238

Page 7 of 12

Step 5: Attach the right panel (1) and a cleat (20) using hardware part E and a screwdriver (not provided).

DO NOT use any power tools as this may damage the frame and will invalidate any claim.

Step 6: Attach the inner top plinth (13) using hardware part C and a screwdriver (not provided).

DO NOT use any power tools as this may damage the frame and will invalidate any claim.

Vendor: S000238

Page 8 of 12

Step 7: Attach the outer top plinth (12) using hardware part F. Attach the top side plinths (17) using

hardware part D. You will need to use a screwdriver (not provided).

DO NOT use any power tools as this may damage the frame and will invalidate any claim.

Step 8: Attach the top panel (10) using hardware part C and a screwdriver (not provided).

DO NOT use any power tools as this may damage the frame and will invalidate any claim.

Vendor: S000238

Page 9 of 12

Step 9: Attach the bottom side plinths (16) and front plinth (15) using hardware part D and a screwdriver

(not provided).

DO NOT use any power tools as this may damage the frame and will invalidate any claim.

Step 10: Insert hardware part N using a small mallet (not provided).

DO NOT use any power tools as this may damage the frame and will invalidate any claim.

Vendor: S000238

Page 10 of 12

Step 11: Insert the hanging rail (18).

DO NOT use any power tools as this may damage the frame and will invalidate any claim.

Step 12: Attach hardware part J to the right door (6) and left door (7) using hardware part B. Attach the door

divider (8) using hardware part D. You will need to use a screwdriver (not provided).

DO NOT use any power tools as this may damage the frame and will invalidate any claim.

Vendor: S000238

Page 11 of 12

Step 13: Position the doors and secure using hardware part B and a screwdriver (not provided).

DO NOT use any power tools as this may damage the frame and will invalidate any claim.

Step 14: Attach hardware part H using hardware part G and a screwdriver (not provided).

DO NOT use any power tools as this may damage the frame and will invalidate any claim.

Vendor: S000238

Page 12 of 12

Step 15: Attach hardware part K using hardware part B, ensuring the small wheels are flush with the base

edge. Insert hardware part L ensuring they are level, then push the door against the hardware to make two

small marks on the door. Secure hardware part L using hardware part B. You will need to use a screwdriver

(not provided).

DO NOT use any power tools as this may damage the frame and will invalidate any claim.

Step 16: Join the back panels (3) using the large spine (9) and small spine (19) and secure using hardware

part O and a small mallet (not provided).

DO NOT use any power tools as this may damage the frame and will invalidate any claim.

Additional Information:

• For complete product information, images and dimension diagrams please visit the website

www.birlea.com

• If you have any issues with your item please contact the retailer directly you purchased it from who

will be able to resolve any issues with Birlea.

• Why don’t you send us photos of your assembled furniture to info@birlea.com to be shared in our

#birleahome feature on Instagram.