Watch your fingers when adjusting clamps. They may become pinched resulting in injury.Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. May injure your fingers.

Before assembly, please make sure that all the items listed below are present.

Snare Pad x 1

Drum Key

Drumstick x 2

ASSEMBLY INSTRUCTIONS

Caution !

Inside This Package

[CYMBAL PADS] box

[DRUM PADS] box

[ACCESSORIES] box

Cymbal Pad x 2 [Hi-Hat Crash (Crash with choke) ]

Tom Pad x 3

Hexagon Key x4

Cymbal Holder (S)

Instruction Manual Assembly Instructions

AC Adaptor

Cymbal Pad x 1( Ride)

Cymbal Holder(L) _Left Cymbal Holder(L) _Right

[HI-HAT PEDAL] box

HI-Hat Control Pedal

Connection Cable X 9[DRUM MODULE] box

Drum Module

[PEDAL] box

Kick Pad

[BASS DRUM PEDAL] box

Foot Pedal

Beater

Assembly

Pillar(L1) Pillar(L2)

Side Arm(L1)Side Arm(L2)

Center Pipe( 2) Center Pipe(1)

Side Arm(R)

Pillar(R1)

Pillar(R2)

Clamp Clamp Clamp

Clamp Holder clamp

Cymbal holder clamp Holder clamp Holder clampHolder clamp

Cymbal holder clampCymbal holder clamp

Setting up the frame of the digital drum set [1] Loosen wing nut on the clamp. [2] Attach Center Pipe (1) to the clamp on the Pillar(L1). [3] Tighten wing nut on the clamp. [4] Loosen wing nut on the clamp. [5] Attach Center Pipe (2) to the clamp on the Pillar(L1). [6] Tighten wing nut on the clamp. [7] Loosen wing nut on the clamp. [8] Attach the Pillar(R1) to the Center Pipe (1) and Center Piper (2). [9] Tighten wing nut on the clamp.

Pillar (L1)

[1] [3]

[2] Center Pipe (1)

[5] Center Pipe (2)

[4] [6]

[10] Loosen wing nut on the clamp. [11] Attach the Side Arm (L1) to the clamp on the Pillar (L1) . [12] Tighten wing nut on the clamp.

[13] Loosen wing nut on the clamp. [14] Attach the Pillar (L2) to the Side Arm (L1) . [15] Tighten wing nut on the clamp.

[16] Loosen wing nut on the clamp. [17] Attach the Side Arm (R) to the clamp on the Pillar (R1) [18] Tighten wing nut on the clamp.

[19] Loosen wing nut on the clamp. [20] Attach the Pillar (R2) to the clamp on the Side Arm(R) . [21] Tighten wing nut on the clamp.

[22] Loosen wing nut on the screw on the clamp. [23] Attach the Side Arm (L2) to the clamp on the Pillar (L1). [24] Tighten wing nut on the clamp.

[7] [9]

[8]

Pillar (R1)Center Pipe (1)

Center Pipe (2)

[7] [9]

Pillar (L2)

[14]

[13] [15]

Pillar (L1)

[23]

[22] [24]

Side Arm(R)

[17]

[16] [18]

Pillar (R1)

Pillar (L1)

[11]

[10] [12]

Side Arm (L1)

Pillar (L1)

Side Arm(L1)

Pillar (R2)

[19],[21]

Side Arm(R)

Side Arm(L2)

[8]

[20]

Center Pipe(1)

Side Arm(R)

[1] Loosen wing nut on the holder clamp which is on the

center pipe(1) side arm(L2)and side arm(R) .

[2] Attach hexagon Key to the holder clamp on center pipe(1)

side arm(L2) side arm(R) .

[3] Tighten wing nuts.Repeat for each hexagon Key.

Attaching hexagon Key to rack

Wing Nut

Felt Washer

2 Attaching cymbals

[1] Remove wing nut and felt washer from cymbal tilter.

[2] Place cymbal pad on tilter assembly.

Re-attach the felt washer and wing nut. Tighten wing nut.

Cymbal Pad

Move Out

Wing Nut

Felt Washer

Side Arm(L1)

Pillar(L1)

Pillar(R1)

Ride

Hi-Hat

Crash[1]

[1]

[2]

[1] Loosen wing nuts on the drum pads.

[2] Attach drum pads to the hexagon Key on center pipe(1)

side arm(L2) side arm(R) and tighten wing nuts.

Repeat for each pad.

Attaching pads to rack

Holder Clamp Holder Clamp

Holder Clamp

Holder Clamp

Side Arm(L2)

[2]

[1],[3]

[1],[3]

[1],[3]

[1],[3]

[2]

[2]

[2]

Side Arm(R)

Center Pipe(1)

Side Arm(L2)

[2] [2]

[2][2]

Center Pipe(1)

Side Arm(R)

Side Arm(L2)

hexagon Key

hexagon Key

Attaching cymbals

[1] Loosen wing nut on the holder clamp on pillar(L1) pillar(R1) and side arm(L1) .[2] Insert each cymbal holder into pillar(L1) pillar(R1) side arm(L1) and tighten wing nuts.

1 Attaching cymbal holders

Side Arm(L1)

Pillar(L1)

Pillar(R1)

Cymbal Holder (S)

Cymbal Holder(L) _Left

[2][2]

[2]

[1] Loosen wing nut on the clamp which is on side arm(L1).

[2] Insert the drum module to the clamp .

[3] Tighten wing nut on the clamp .

Attaching module

Side Arm(L1)

[2]

[1],[3]

[1][1]

[1]

Cymbal Holder(L) _Right

Cymbal Holder(L) _Left Cymbal Holder(L) _Right

Wing Nut

Felt Washer

Cymbal Tilter

Cymbal Holder (S)

Wing Nut

Felt Washer

Move Out

[1]

Move Out

[1]

Cymbal Tilter

Cymbal Tilter

[1]

[1]

[2]

Beater

[5]

[6]

[3]

DD512_G02

Attaching the Kick Trigger

[1] Attach the Rod to the holders.

[2] Attach the Kick Pedal to the Kick Pad.

[3] Tighten the wing screw on the Kick Pedal.

[4] Loosen the screw.

[5] Attach the Beater to the Kick Pedal.

[6] Position the Beater from the center of the pedal, tighten the screw.

Attaching the Kick Trigger

Pedal /Bass drum pedal

Drum Pad

Bass drum pedal

[1] Place the pedal on the floor on your left side.

[2] Place the bass drum pedal on the floor in the center of rack.

[3] Please connect the clearly marked cables from the pads to

the correct inputs on the drum module, and you are ready to

play!

To Kick

Tom 3To

Tom 1To

Cymbal Pad

To Crash

Hi-HatTo

Drum Module

RideTo

Tom 2To

SnareTo

To Hi-Hatcontrol

Hi-Hat Pedal

[2][1]

Attaching the Drum Throne ___(Optional)

[1] Attach the standard-gauge tubing to the round seat.

[2] Tighten the wing nut on the round seat.

[3] Open the legs.

[4] Remove the wing nut and screw attached to the

Double-Braced Legs.

[5] Attach the standard-gauge tubing to the

Double-Braced Legs.

[6] Reattach the wing nut and screw.

[7] Tighten the wing nut and screw.

,

Attaching the Drum Throne

Round Seat

[Stool box] (Optional)

Standard-gauge tubing

Double-Braced Legs

[1]

[2]

[3] [3]

[3]

[4]

[5]

[6] [7]

Headphones

[HEADPHONES] (Optional)

[4]