Upload
ivan-nikolic
View
70
Download
2
Embed Size (px)
DESCRIPTION
ARC
Citation preview
5/28/2018 ArtCAM Tutorijal 10
1/5
ArtCAM Tutorials J.C.Lee 2007
1
2 Rail Sweep : Torch Casing
Use Snap Grid Settingsin 2D Viewpull
down menu make sure Snap to Guidlinesis ticked.
In Snap Grid SettingsSet a 1mm grid and make sure Snap to Grid
and Draw Snap Gridare selected.
Drag a guideline into the model centre from the rulerat the LH side of the screen
Use the Create Polyinetool in the Vectortoolbar tocreate a vector shape as shown below
Use the Fillet Vectortool to create a 6mm radius ateach corner
This task uses the Two Rail Sweep wizardto create a complex 'organic' form based onthe Polaroid Polar Plus torch.
The Two Rail Sweep uses at least two edgeprofiles and one cross section. This can bedone simply by using the vector drawing andediting tools.
Create a new ArtCAM model say 150 mmx 120mm
5/28/2018 ArtCAM Tutorijal 10
2/5
ArtCAM Tutorials J.C.Lee 2007
2
Use the Node Editingtool toselect the vector
Right clickon the top line and
choose Convert span toBezier
Use the white grab handles tocreate a curved line as shownon right
Repeat the process for the lower line
until your shape looks like the oneshown on the left
Now select the vector and use the
Mirror Vectorstool to copy it asshown below
Choose Mirror type > Right(andremember to check the box that says
Copy the original vector)
You now need to create another vector that willrepresent the cross section of your casing. ( this canbe drawn anyw here on the screen)
Use the Create Polyline Vectorand Node editing
> Convert span to bezieragain to create a crosssection looking like the one shown below(Note
how two guidelines have been used to helpconstruct the vector.)
5/28/2018 ArtCAM Tutorijal 10
3/5
ArtCAM Tutorials J.C.Lee 2007
3
You are now ready to create the Two
Rail Sweep
Open the Two Rail Sweepwizard
Select the LH vector and in the
Select Control Vectors section
click on Top Drive Rail > Select
Repeat the process for the RH vector
but this time click on Bottom Drive
Rail > Select
Now scroll down the Two Rail Sweeppanel until
you can see Add Cross Section
Select your cross section vector and click on Add
Cross Section
Scroll to the bottom of the panel and click
Calculate
Look in the 3D view to see the result which shouldlook something like the model shown below
The next task is to add the raised area for the lens. This is done using the Merge Highcommand as
follows.
5/28/2018 ArtCAM Tutorijal 10
4/5
ArtCAM Tutorials J.C.Lee 2007
4
First go back to the 2D view and convert the model
to Greyscale from Relief
Nextuse theCreate Ellipse tool to sketch anellipse for the raised area as shown below.
Now double click on the ellipse to open the Shape
Editor
Choose the rounded raiseuse the slider tocreate a deeply rounded profile
Click onMerge High > Apply > Close
To see the effect, go to the 3D view, which shouldlook something like the one below
The lens can now be trimmed back to matchthe body shape by zeroing everything that is
coloured black using the Shape Editor
To do thisdouble click on the black square at the bottom of the screen to
open the Shape Editor (Note: This will not be the first black that appearsbut the one further along as shown below)
5/28/2018 ArtCAM Tutorijal 10
5/5
ArtCAM Tutorials J.C.Lee 2007
5
Things to try: The membrane switch is simple enough to addit just requires two concentric ellipses.
The Polaroid text can also be added.
In the Shape Editor, click Zero.
This will return everything black back to the zeroplane
Your model show now look like the one below with
the front of the lens trimmed to match the body
To see the effect, go to the 3D view, which shouldlook something like the one below