Arrow Straightening

Embed Size (px)

Citation preview

  • 7/29/2019 Arrow Straightening

    1/4

    Arrow Straightening

    by Dick Baugh

    The use of heat for manipulating the shape of wood is a fundamental Stone Age woodworking technique. Heat is and was used initially to straigh

    spear and arrow shafts and also for periodic maintenance of straightness.

    Typically, the shaft material is gathered in the green state, straightened with heat while still green and then tied into a bundle to dry. Some shaft

    materials will check if they are dried too quickly. To prevent this put wax or pitch on the ends and don't peel the bark until the shafts are dry.

    Patience! The contemporary primitive technologist can speed up the drying process by placing the bundle of shafts in the interior of a car in summ

    time.

    One can apply heat to the shaft in several ways. For taking out long curves you can apply the heat of a small fire. For removing kinks you need a

    heat source which is concentrated in a small region of the shaft. The best way to do that is to use a piece of soapstone (steatite) with a semicircular

    groove. Heat the soapstone until it will fry spit (same criterion used by grandma for the pancake griddle). Use a pair of tongs to remove the

    straightener from the fire and place it on a slightly raised platform.

    The smaller one was recently made from soapstone. The larger is an authentic artifact, provenance unknown. It would be excellent for removing

    sharp kinks.

    Two arrow straighteners

    Place the part of the shaft to be straightened in the groove and rotate it. Rotating the shaft accomplishes two tasks. It applies the heat to the entire

    circumference of the region being straightened and it gives you a "feel" for where the high spot is. When the wood is hot then push down on both

    sides of the shaft to remove the bend. If you have never done this before then practice with something you don't care about. It's done by feel. This

    technique is especially valuable for bamboo, river cane, and phragmites which tend to collapse or buckle when bent with too much vigor. Anotherthing to do with shaft material which tend to buckle is to apply tension. Pulling on the ends of the shaft will reduce the tendency to buckle.

    4/28/05 4:rrow Straightening

    Pagettp://primitiveways.com/arrow_straightening.html

  • 7/29/2019 Arrow Straightening

    2/4

    The process of straightening a shaft with a heated arrow straightener.

    How hot is too hot? Ishi, a Native Californian and consummate craftsman who lived during the late nineteenth and early twentieth centuries, was

    disgusted with himself if he scorched an arrow shaft while straightening it. The wood should be heated hot enough to be uncomfortable to the tou

    but not hot enough to discolor.

    Straightening the middle of a shaft is relatively easy because you have a "handle" on both sides but what about the ends of a shaft? Push down on

    the short end of the shaft with a small stick.

    Arrow shafts before and after straightening.

    Soapstone is a superior material for arrow straighteners because it possesses three important properties. It doesn't crack or explode when heated, i

    easily shaped and it is very soft and smooth so it won't scratch the wooden shaft being straightened. If you don't have soapstone then try the local

    materials. The first test you should do, even before you cut a groove in the stone, is to see if the stone retains its structural integrity while being

    heated.

    4/28/05 4:rrow Straightening

    Pagettp://primitiveways.com/arrow_straightening.html

  • 7/29/2019 Arrow Straightening

    3/4

    Soapstone arrow straightener Dino Labiste 2000

    I also use heat to straighten a lot of spindles for starting hand drill fires. The materials I use, in order of preference are mare's tail (Conyza

    canadensis), mule fat (Baccharus virrinea) and elderberry (Sambuca spp). Several skeptics have asked me, "If you use heat from a fire to straighte

    the spindle you use to start a hand-drill fire, isn't that cheating?"

    Yes, it is cheating but there is a way around it. One can heat straighten hand-drill spindles by using the heat of friction. Lay the crooked spindle o

    log or flat surface with the convex side up. Then take a piece of dry, low density wood (like a hearthboard) and rub vigorously back and forth on

    part which needs straightening.

    Straightening a hand-drill spindle using friction heat.

    Another tool which is useful in heat straightening is the so called "arrow wrench". The arrow wrench is a 1ever about 10 inches (25 cm) long wit

    hole in one end. The wrench allows you to apply leverage to a small portion of the shaft. It can be made of wood or antler. The sides of the hole

    should be rounded in order to prevent denting the side of the shaft being straightened.

    4/28/05 4:rrow Straightening

    Pagettp://primitiveways.com/arrow_straightening.html

  • 7/29/2019 Arrow Straightening

    4/4

    Antler arrow straightener Dino Labiste 2000

    This article was first published in (Fall, 2001, #22)

    E-mail your comments to "Richard A. Baugh" at

    The Bulletin of Primitive Technology

    [email protected]

    The PrimitiveWays Book

    The PrimitiveWays CD

    PrimitiveWays Home Page

    1998 - 2003PrimitiveWays

    4/28/05 4:rrow Straightening

    Pagettp://primitiveways.com/arrow_straightening.html