Upload
dinhdung
View
235
Download
1
Embed Size (px)
Citation preview
AR822-II
AR861-2II
AR861-3II
INSTALLATION, OPERATION & MAINTENANCE MANUAL
Information and specifications outlined in this manual in effect at the time of printing of this manual. ECR International, Inc. reserves the right to discontinue, change specifications or system design at any time without notice and without incurring any obligation, whatsoever.
ARGO AR SERIES CONTROLS
AR822-II, AR861-2II, AR861-3II
Manufactured by:
ECR International, Inc.2201 Dwyer Avenue, Utica NY 13501
web site: www.ecrinternational.comwww.argocontrols.com
P/N 24005122 Rev. B [07/30/2016]
Safety Symbols ���������������������������������������������������������������������������������������������������������������������������������3
Introduction ��������������������������������������������������������������������������������������������������������������������������������������3
Mounting Instructions ������������������������������������������������������������������������������������������������������������������������3
Electrical Specifications & Wiring ���������������������������������������������������������������������������������������������������������4
AR822-II Single Zone Relay
AR822-II Control Features �����������������������������������������������������������������������������������������������������������4
AR822-II Sequence Of Operation ��������������������������������������������������������������������������������������������������4
AR822-II Control Board���������������������������������������������������������������������������������������������������������������5
AR822-II Wiring Schematic ���������������������������������������������������������������������������������������������������������5
AR822-II Applications �����������������������������������������������������������������������������������������������������������������6
AR822-II With Zone Valve Priority ������������������������������������������������������������������������������������������������7
AR861-2II & AR 861-3II
AR861-2II & AR 861-3II Control Features �������������������������������������������������������������������������������������8
AR861-2II & AR 861-3II Sequence of Operation������������������������������������������������������������������������������8
AR861-2II Control Board & Wiring Schematic................................................................................9
AR861-3II Control Board & Wiring Schematic��������������������������������������������������������������������������������10
AR861-2II & AR 861-3II Applications ������������������������������������������������������������������������������������������ 11
AR861-2II & AR 861-3II Expansion Control���������������������������������������������������������������������������������� 15
AR Series With DPM-2 Outdoor Reset Control................................................................................16
Replacement Parts ��������������������������������������������������������������������������������������������������������������������������� 16
Technical Support ���������������������������������������������������������������������������������������������������������������������������� 16
DANIMPORTANT: Read and understand the following instructions COMPLETELY before installing!!
TABLE OF CONTENTS
Keep this manual near boilerRetain for future reference
2 P/N 240005122, Rev. B [07/15/2016]
INSTALLATION MANUAL AND OPERATING INSTRUCTIONS
NOTICEUsed to address practices not related to personal injury�
CAUTIONIndicates a hazardous situation which, if not avoided, could result in minor or moderate injury�
!
WARNINGIndicates a hazardous situation which, if not avoided, could result in death or serious injury�
!
DANGERIndicates a hazardous situation which, if not avoided, WILL result in death or serious injury
!
This is the safety alert symbol� Symbol alerts you to potential personal injury hazards� Obey all safety messages following this symbol to avoid possible injury or death�
Become familiar with symbols identifying potential hazards�
WARNINGFire, explosion, asphyxiation and electrical shock hazard� Improper installation could result in death or serious injury� Read this manual and understand all requirements before beginning installation�
! Introduction
This manual is intended to familiarize the installer and user of the Argo AR Series of controls with their installation and operation to assure normal trouble-free operation�
Argo controls are designed and manufactured with quality components for maximum life and durability and require minimal service� To insure a satisfactory installation, it is imperative that the instructions be followed carefully before operating the control� Failure to do so may result in breach of warranty�
Mounting InstructionsMount the Argo AR Series Control vertically on a solid wall or partition� For your convenience it is recommended that the control be mounted as close as possible to the device to be controlled� The control should never be mounted more than 75 feet away� Select a location that is easily accessible for installation and service�
NOTE: To reduce the possible transformer hum and relay noise that is sometimes amplified by mounting surfaces such as sheet metal, plasterboard, and similar materials, place rubber or felt washers between the case and the mounting surface�
1. Position the control and mark the mounting holes.
2. Start screws (not provided) for the keyhole type mounting holes in the upper corner(s)� Tighten the screws down to about ⅛” (3mm) from the surface. The AR822-II will require a screw to be installed in the lower left hand corner after the control is hung and leveled�
3. Hang the control on the screw(s), position the case, and start the bottom screws�
4. Tighten all screws�
3 P/N 240005122, Rev. B [07/15/2016]
The following describes the function of each terminal.
• L1: Hot leg of 120VAC power input
• L2: Common leg of 120VAC power input
• 3: Input to one pole of relay contacts
• 4 NO: Normally open output, between 3 and 4 NO
• 4 NC: Normally closed output, between 3 and 4 NC
• 5: Input to one pole of relay contacts
• 6 NO: Normally open output, between 5 and 6NO
• 6 NC: Normally closed output, between 5 and 6NC
T/R and T/W are thermostat connections� When Thermostat calls completing the circuit the relay is activated�
AR822-II Sequence of Operation
1. When the thermostat connection to TR/TW calls for heat the “circuit ON” LED is illuminated.
2. The relay will then close.
3. The contacts between 3/4 NO and 5/6 NO will close.
4. The contacts between 3/4NC and 5/6NC will open.
Electrical Specifications
Part Number
Model Number
Transformer Voltage
Relay Switching
Action
Contact/Control
Amp Draw (120VAC)
Z140 AR822-II 120V/60Hz/40Va DPDT 7.2
Z209 AR861-2II 120V/60Hz/75Va DPDT 7.2
Z210 AR861-3II 120V/60Hz/75Va DPDT 7.2
AR822-II Control Features
• Auto-Reset Electronic Fuse Protection – Eliminates Nuisance Service Calls
• 15VA Transformer – Robust Components Provide Years of Trouble -Free Service
• Ice Cube Technology – Plug-In Replacement Relays
• 5-Year WarrantyGeneral Wiring Notice
All primary wiring must be 14 AWG minimum. Torque terminal screws 6 to 7 inch pounds.
U.S.A. - National Electric Code and any other nation-al, state, or local code requirements. Wiring must be N.E.C. Class 1.
CANADA - C.S.A. C22.1 Canadian Electrical Code Part 1 and any other national, provincial, or local code requirements. Wiring must be C.S.A. C22.1 C.E.C. Part 1.
INSTALLATION MANUAL AND OPERATING INSTRUCTIONS
Electrical Specifications & Wiring
WARNINGElectrical shock hazard. Disconnect power before installing or servicing� Failure to follow these instructions could result in death or serious injury�
!
4 P/N 240005122, Rev. B [07/15/2016]
ELEC
TRO
NIC
FU
SE
VAC
CIRC
UIT
ON
120
L2NO
4NC
4
SCREWSTORQUE TERMINAL
6 TO 7 INCH LBSAR822-TTARGO TT
TTR W
24V
C 5 6NO
6NC
RE
LAY
Factory Installed Jumper Between L1 & 3
Class 2Terminals
PrimaryTerminals
INSTALLATION MANUAL AND OPERATING INSTRUCTIONS
AR822-II CONTROL BOARD
AR822-II WIRING SCHEMATICS
5 P/N 240005122, Rev. B [07/15/2016]
TO BURNER
OR BURNER
CONTROL
DO NOT USE
AR822-II Dual Zone Applicationwithout Tankless Coiler Boiler
AR822-II Single Zone Applicationwith Tankless Coil Boiler
AR822-II APPLICATIONS
INSTALLATION MANUAL AND OPERATING INSTRUCTIONS
6 P/N 240005122, Rev. B [07/15/2016]
L2120VAC
L1
CIRC
UIT
ON +
NO
3NC
4 4
ARGO AR822
WR CTT 24V
5 6 6NO NC
BURNER CONTROLTO BURNER OR
DO NOT USE
L8148
2
1
T
C2
B1
C1
B2
T
PRIORITYCIRC.
24 VAC
COM
TX-X TT TT T TT TTON
ZONE 2
END SW 2
X2X1
END SW 1
X1 X2
ZONE 121 3 4 1 2
AZ-
3
ARG
O
Zone
Val
ve C
ontr
olle
r
ZONE 343 1 2 43
AZ-
5
ZONE 41 2 43 3
ZONE 51 2 4
SUPPLIEDWITH RELAY AZ-5
STAT STAT STAT STAT STAT
VALVE VALVE VALVE VALVE VALVE
DOMESTICHOT
WATER
L
N
120VAC
JUMPER
N120VAC L
HEATINGZONEPUMP
120VAC
L
N
NOTE: Thermostats must be mercury switch style or battery powered for this installation to function properly�
AR822-II Indirect Tank Prioritywith Zone Valve Control
INSTALLATION MANUAL AND OPERATING INSTRUCTIONS
AR822-II APPLICATIONS
7 P/N 240005122, Rev. B [07/15/2016]
INSTALLATION MANUAL AND OPERATING INSTRUCTIONS
AR861-2II & AR861-3II Control Features
• 2-Zone AR861-2II or 3-Zone AR861-3II
• Auto-Reset Electronic Fuse Protection – Eliminates Nuisance Service Calls
• 15VA Transformer – Robust Components Provide Years of Trouble -Free Service
• Ice Cube Technology – Plug-In Replacement Relays
• Priority Function
• 5-Year Warranty
AR861-2II & AR861-3II Sequence of Operation
If the Priority Switch is in the “OFF” Position:
1. When a zone calls for heat the corresponding zone LED is illuminated.
2. The relay for the corresponding zone will then close.
3. A/R terminals will close starting the boiler.
4. The corresponding GZ/HZ terminals will be energized with 120 Volts.
If the Priority Switch is in the “ON” Position:
1.Zone 1 becomes the priority zone.
2. When zone 1 calls for heat, the priority zone is activated and all other zones are deactivated (circulators for zones 2 and higher will not operate). Zone 1 LED is illuminated indicating a call for heat.
3. Zone 1 relay will close.
4. A/R terminals will close starting the boiler.
5. GZ 1/HZ 1 will be energized with 120 Volts.
8 P/N 240005122, Rev. B [07/15/2016]
RE
LAY
RE
LAY
RE
LAY
Class 2 Terminals
Primary Terminals
INSTALLATION MANUAL AND OPERATING INSTRUCTIONS
AR861-2II CONTROL BOARD & WIRING SCHEMATIC
9 P/N 240005122, Rev. B [07/15/2016]
RE
LAY
RE
LAY
RE
LAY
RE
LAY
Class 2 Terminals
Primary Terminals
INSTALLATION MANUAL AND OPERATING INSTRUCTIONS
AR861-3II CONTROL BOARD & WIRING SCHEMATIC
10 P/N 240005122, Rev. B [07/15/2016]
The diagrams on the following pages represent the AR861-3II. The AR861-2II is wired in a similar fashion.
Priority T-Stat
Primary Wiring
Class 2 Wiring
AR861-3II
Primary WiringJumper
Priority Circ L4006A
T-StatT-Stat
Circ
L2G W L A R GZ1
T1 T1 T2 T2 T3 T3
HZ1 GZ2 HZ2 GZ3 HZ3
G Circ
120 VACL1Hot
Milli VoltGas Valve
RE
LAY
RE
LAY
RE
LAY
RE
LAY
Each of the low voltage controllers (SPST Thermostats) will actuate a circulator and start the burner when used in conjunction with an isolated switch aquastat.
Jumper: To be placed between terminals L and W . In this position A and R become the isolated end switch. (Jumper is factory installed in this position)
Terminals A and R Isolated End Switch
INSTALLATION MANUAL AND OPERATING INSTRUCTIONS
AR861-2II & AR861-3II APPLICATIONS
11 P/N 240005122, Rev. B [07/15/2016]
Priority T-Stat
Primary Wiring
Class 2 Wiring
AR861-3II
Primary WiringJumper
Priority Circ L4006A
T-StatT-Stat
Circ
L2G W L A R GZ1
T1 T1 T2 T2 T3 T3
HZ1 GZ2 HZ2 GZ3 HZ3
G Circ
Milli VoltGas Valve
120 VACL1Hot
24VTransformer
Priority T-Stat
L8148
Primary Wiring
To Burner or
Burner Control
DoNotUse
Class 2 Wiring
AR861-3II
Primary WiringJumper
Priority Circ
T-Stat
T-Stat
TT
1
2
Circ
G W L A R GZ1
T1 T1 T2 T2 T3 T3
C1
C2
B2
B1
HZ1 GZ2 HZ2 GZ3 HZ3
CircL2
G
120 VACL1Hot
AR861-2II & AR861-3II APPLICATIONS
INSTALLATION MANUAL AND OPERATING INSTRUCTIONS
12 P/N 240005122, Rev. B [07/15/2016]
RE
LAY
RE
LAY
RE
LAY
RE
LAY
Terminals W and R to Aquastat( W to ZC and R to ZR)
Each of the low voltage controllers (SPST Thermostats) will actuate a circulator and start the burner when used in conjunction with a boiler aquastat control. If the boiler temperature drops below the low limit (circulator) setting, all circulating will cease until the temperature of the boiler water is increased.
Jumper: To be placed between terminals L and A . In this position a line voltage message is sent out R to ZR terminal on the aqustst and returns to W from the ZC terminal on the aqustst.
INSTALLATION MANUAL AND OPERATING INSTRUCTIONS
AR861-2II & AR861-3II APPLICATIONS
WARNINGAR relays will not work properly if 120 VAC polarity is not the same at 120 VAC L and N terminals on both AR control and boiler aquastat� The neutral and hot wires must not be reversed� Reversing the L and N wires could result in a secondary source of power that may activate the boiler under certain circumstances which could result in death or serious injury�
!
WARNINGWhen using ZC-ZR attention must be paid to keep the polarity of the wiring consistent between the Argo control and boiler aquastat� Failure to do so could result in a secondary source of power activating the boiler under certain circumstances which could result in serious injury or death� Always disconnect power to both the Argo control and boiler when installing or servicing this product�
!
13 P/N 240005122, Rev. B [07/15/2016]
Priority T-Stat
Primary Wiring
Burner
Class 2 Wiring
AR861-3II
Primary WiringJumper
Priority Circ
T-StatT-Stat
L8124A or C
T
T
L1
L2
Circ
G W L R GZ1
T1 T1 T2 T2 T3 T3
C1
C2
B2
B1
ZR
ZC
HZ1 GZ2 HZ2 GZ3 HZ3
CircL2
G
120 VACL1Hot
A
Priority T-Stat
Primary Wiring
Burner
Class 2 Wiring
AR861-3II
Primary WiringJumper
Priority Circ
T-StatT-Stat
L8124A or C
T
T
L1
L2
Cad
Cell
Circ
G W L R GZ1
T1 T1 T2 T2 T3 T3
C1
C2
B2
B1
ZR
ZC
HZ1 GZ2 HZ2 GZ3 HZ3
CircL2
G
120 VACL1Hot
A
AR861-2II & AR861-3II APPLICATIONS
INSTALLATION MANUAL AND OPERATING INSTRUCTIONS
14 P/N 240005122, Rev. B [07/15/2016]
THERMOSTATS
GZ2120 V CIRCULATOR
15VA
120VACG W L RA
PRIORITYGZ1 HZ1
PRIORITY OFF
PRIORITY ON
PRIORITYT1 T1 T2
GZ3HZ2 HZ3
T3T3T2
STATSTAT
CIRC CIRCDO NOTUSE
N
L
120VAC
CIRC
STAT
T2
120 V CIRCULATORGZ2
THERMOSTATS
15VA
L
120VAC
N
W120VAC
G L A GZ1PRIORITY
R HZ1
PRIORITY OFF
PRIORITY ON
2.7 K
1.0 K
2.7 K
1.0 K
PRIORITYT1 T2T1
CIRC
HZ2 GZ3 HZ3
1.0 K
2.7 K
T3 T3
STAT
CIRC
TO BOILERT-T
TO BOILERT-T
DOMESTIC
WATERHOT
JUMPER
JUMPER
TRIPLE RELAY AR861-3 IIARGO
TRIPLE RELAY AR861-3 IIARGO
The two controls on this page are capable of running six zones. When they are installed as shown below, only one priority and four standard zones (for a total of five zones) are available.
Important:Both left-hand T1 terminals must be connected together and both right-hand T1 terminals must be connected together� Reversing the wiring will result in the transformers being out of phase�
INSTALLATION MANUAL AND OPERATING INSTRUCTIONS
AR861-2II & AR861-3II EXPANSION TECHNIQUE
15 P/N 240005122, Rev. B [07/15/2016]
The DPM-2 Outdoor Reset Control is designed to raise or lower the temperature of the boiler supply water based upon a proportionate drop or rise in temperature at the outside sensor� This control plugs into Argo control equipment with a data port or as a stand alone device that can be easily wired into almost any system� See the separate DPM-2 Installation Manual for more information.
Replacement PartPart Description Argo Part Number
Replacement Control Relay R35C
For technical support on this and all Argo products, please contact ECR International Technical Service at 1-800-325-5479. Please have your model number available when calling.
Information Needed When Calling
Model Number
Installation Date
Installer
INSTALLATION MANUAL AND OPERATING INSTRUCTIONS
AR SERIES WITH DPM-2 OUTDOOR RESET CONTROL
Technical Support
ECR International2201 Dwyer Avenue
Utica, NY 13501www.ecrinternational.com
www.argocontrols.com
P/N 240005122, Rev� B [07/15/2016]