AquaView ~ ASSand Filter with 7 Position ValveModel — 0-1709-014 14" Sand Filter

Model — 0-1709-017 17" Sand Filter

Model — 0-1709-020 20" Sand Filter

Model — 0-1709-024 24" Sand Filter

Owner's Guide

365-1993-1

™

2

Before you begin installing your filter,refer to your pump owners guide forvery important installation andelectrical information related to yourfilter.

ELECTRICAL/BUILDINGPERMIT

Local building codes may requireobtaining an electrical or buildingpermit and may have regulations onset backs and barriers that must befollowed.

ELECTRICALWe recommend you have a qualifiedelectrical contractor install theelectrical power supply as specifiedin your pump instructions.

INSTALLED LOCATIONPosition filter, pump and any otherrelated components a minimum of 5feet from pool to prevent their beingused as a means to climb into thepool by young children. DO NOTstore toys, chairs, tables, containersor other objects within 5 feet of thepool for the same reason.

WARNING

SEVERE ELECTRICAL SHOCKcould result if you install your filterand pump on a deck or above poolwater level. They could fall into thewater, causing severe shock orelectrocution. DO NOT install on adeck or other surface at, above orslightly below the top rail of the pool.

PROPERLY SUPPORTEDFilter, pump and any other relatedcomponents should be properlysupported to prevent damage frommisalignment, settlement, vibrationand mounted so as to minimize thepotential for the accumulation ofdebris and moisture.

ACCESSIBILITYThe circulation systemcomponents should be installed toallow accessibility for inspection,repair or replacement. DO NOTalter the pump electrical cord in anyway or change the plug end to anystyle. DO NOT use an extensioncord(s). Severe electrical shock mayoccur.

PREVENT SEVERE SHOCKTo prevent the risk of severe electri-cal shock, plug your pump cord endinto a grounding type receptacleprotected by a ground fault circuitinterrupter (GFCI). Contact a quali-fied electrician if you cannot verifythat the receptacle is protected by aGFCI.

DO NOT allow children to operate orplay around this product unless theyare closely supervised by adults at alltimes.

Replace damaged cord immediatelyto reduce the risk of electrical shock.

DO NOT BURY CORDAn unexposed cord may accidentallybecome damaged or severed by asharp object or shovel resulting insevere electrical shock. Position cordto prevent accidental damage fromlawn mowers, hedge trimmers orother equipment.

BARE FEET/WET GROUNDThis is a dangerous combinationaround electrical equipment. Alwaysbe sure the ground under your feetand body is dry before you touchelectrical equipment. Failure to heedthis warning may cause severepersonal injury or electrocution dueto severe electrical shock.

WARNING

Avoid direct water spraying with agarden hose around electricaloutlets, pump or any other electricaldevices. Severe electrical shock orelectrocution may occur.

SERVICING YOUR PUMPAlways unplug your pump from thereceptacle before servicing, adjustingor repairing.

“READ ALL INSTRUCTIONS.” Failure to follow these important safetyinstructions and other basic safety precautions may result in seriouspersonal injury.

IMPORTANT SAFETY INSTRUCTIONS

3

FIG. 1

Did you read the IMPORTANTSAFETY INSTRUCTIONS? If not,READ THEM NOW. They containvery important safety informationrelated to the installation of your filter.Familiarize yourself with the installa-tion sequences by reading theseinstructions first. AVOID SHORT-CUTS that may result in reworkingthe installation.

BEFORE YOU BEGINThe pool must be properly erectedper your pool assembly and installa-tion instructions before installing thefilter. Install the surface skimmer andreturn fitting.

Before completing the filling of thepool to the water level indicatormarks on the skimmer face plate, thefilter and pump should be installedwith all connections secured tightly.

TOOLS REQUIRED• 3/8" nut driver• Flat head screwdriver• Flat shovel• Carpenter Level• Tape Measure• 5/16" Nut Driver (optional)

MATERIALS REQUIRED• Nine 12" x 12" patio blocks• Waste hose - 1-1/2" inside

diameter• 1-1/2" hose clamp• Silicone lubricant (available at

pool dealer)and included• Ordinary plastic bag• #20 grade filter sand

Model 014 - 80 lbs.Model 017 - 150 lbs.Model 020 - 200 lbs.Model 024 - 300 lbs.

INSTALLATIONINSTALLATION LOCATION

Install your filter and pump and anyother related components at least 5feet from the pool to prevent theirbeing used as a means of access tothe pool by young children. Patioblocks provide firm support andkeep standing water and weedsaway from electrical parts. DO NOTinstall your filter and pump basedirectly on the ground surface. Settlingand stressing of circulation lines mayoccur during wet seasons. Positionpatio blocks as illustrated, use ashovel and carpenter’s level to levelground before placing the blocks.

POSITIONING FILTER/PUMPPosition the filter and pump asshown in Fig. 1. Make sure filter ispositioned in base correctly, oncesand is installed it will be difficult tomove.

INSTALL FILTER SANDYour filter is designed to providepeak performance using #20 gradefilter (.4/.5 mm) sand. The sandshould be uniform in size and appearas crushed sand with sharp edges.Rounded river bed sand will not filterproperly. Consult your local poolstore.

REMOVE VALVERemove valve from tank by pulling upand twisting back and forth.

COVER RISER TUBESlip a plastic bag over the riser tubeand secure with rubber band.

INSTALL SANDGently pour filter sand into tank andlevel surface with palm of hand.Remove any sand from plastic bagand tank flange sealing surface.Remove rubber band and plastic bag.

REINSTALL VALVESee illustrations on following page toinstall the valve and o-rings.

Position large square o-ring (308-1282) on bottom groove of valve,position the large round o-ring(308-1280) all the way up to the valveflange. Lubricate o-ring with non-petroleum grease. Place valve ontank top and press firmly until roundo-ring is seated with tank flange.

Install tank clamp, sandwiching valveand tank flanges. Tighten clampscrews securely but do not over-tighten.

Please refer to the pictures on thefollowing page for proper O-ringplacement.

RETURNSKIMMER

PUMP FILTER

4 FT.

FIG 1

NEW FILTER START UP

AFTER ADDING THE CORRECT

SAND, #20 grade filter (.4/.5

mm) sand, AND CORRECT

AMOUNT.

BACKWASH FILTER PRIOR TO

RUNNING IN FILTER POSITION.

THIS WILL CLEAN THE SAND AND

ELIMINATE FINE SAND

PARTICLES FROM ENTERING

POOL AND PLUGGING UP

UNDERDRAIN SLOTS. AFTER

BACKWASHING, RUN IN FILTER

TO WASTE FOR APPROX. 30

SECONDS TO FLUSH FILTER.

NOW THE UNIT IS READY FOR

NORMAL FILTERING OPERATION.

4

VALVE INSTALLATION - PLEASE READ

Position round o-ring all the way to the flange and

position the square o-ring in the groove as shown.

Lubricate with non-petroleum grease.

STEP 2

Position valve to tank by aligning

underdrain riser tube with opening

in bottom of valve.

Press down firmly until the large

round o-ring is seated to tank

flange.

STEP 3

Complete by installing tank clamp

halves. Tighten clamp screws

securely but do not over-tighten.

STEP 4

STEP 1

ROUND O-RING POSITION:PUSH ALL THE WAY UPPAST GROOVE

SQUARE O-RING POSITION:IN GROOVE

5

INSTALL HOSES

See Fig. 1 and ExplodedParts Illustration

IMPORTANT: Incorrect hosehookup could cause damage to yourfilter system. Follow the instructionsbelow carefully.

Suction and return lines should bepartially buried to prevent accidentaltripping that could cause personalinjury or damage to the filter system.Be sure the hoses are routed so thatwater flow through them is notrestricted.

Starting at least 12" from the poolwall, make two 3-4" deep trenches,one from the pool skimmer to thefront of the pump and the other fromthe pool return fitting to the filter/valve return port.

The two 8 ft. long hoses (Item 13Model 014, 017 Item 21 Model 020,024), are interchangeable and usedfor the suction and return lines. Slipa hose clamp over the ends of eachhose prior to installing. Connect onelong hose (suction line) between thepool skimmer and front port of thepump. Connect the other long hose(return line) between the pool returnfitting and the filter/valve port marked"RETURN". Connect the short hose(Item 15 Model 014, 017, Item 23Model 020, 024) between the pumpdischarge port (located at top ofpump) and the filter/valve portmarked "PUMP". Tighten clampsfirmly using a flathead screwdriver or5/16" nutdriver. Cover the trencheswith a firm board when finished.

NOTE: Do not completely bury thehoses with dirt.

NEW FILTER START UP

AFTER ADDING THE CORRECT

SAND, #20 grade filter (.4/.5

mm) sand, AND CORRECT

AMOUNT.

BACKWASH FILTER PRIOR TO

RUNNING IN FILTER POSITION.

THIS WILL CLEAN THE SAND AND

ELIMINATE FINE SAND

PARTICLES FROM ENTERING

POOL AND PLUGGING UP

UNDERDRAIN SLOTS. AFTER

BACKWASHING, RUN IN FILTER

TO WASTE FOR APPROX. 30

SECONDS TO FLUSH FILTER.

NOW THE UNIT IS READY FOR

NORMAL FILTERING OPERATION.

6

WASTE LINE HOOKUPThe discharge waste water willcontain pool water treatment chemi-cals that may harm certain plantsand vegetation. Therefore, positionthe discharge end of the waste line ina safe, out-of-sight area capable ofaccepting 150 to 200 gallons ofwaste water. Install a 1-1/2" insidediameter waste discharge hose (notsupplied) on the waste port nearwhere the sight glass is located onthe valve. Slip a 1-1/2" hose clamp(not supplied) over one end of thehose. Then, push hose onto the portfully and tighten clamp firmly.

plugging the underdrain slots.Because pool water is lost duringthis operation (150 to 200gallons) keep a close check onpool water level. Never let waterlevel get so low that no waterflows to pump. Refill pool asrequired.

5. Push down on the valve handleand rotate to the FILTER positionand start pump. Note thepressure reading on your pres-sure gauge for future referenceof when to backwash.

6. Check all fittings and hoses forleaks and correct ifnecessary.

FILTER OPERATIONA newly filled pool is normally filledwith unfiltered water and usuallyrequires continuous filtering for 24 to48 hours along with chemical treat-ment of the pool water. Because allpool installations vary in environmen-tal conditions (wind, rain, airbornedebris, heat and pool use, etc.),it is impossible to provide an accu-rate filtering time for normal usage.Use a trial and error method todetermine how long your filter mustoperate each day. Generally, 6 to 8hours of filtering each day is suffi-cient to maintain pool clarity if thepool chemical treatment is correct.

When possible, avoid operating yourfilter during peak electricity demandsin your community. Check with yourlocal electric utility company for thebest times they recommend foroperating your filter pump.

WHEN TO BACKWASHAs your filter removes debris from thepool water during the filtering pro-cess, the return flow will graduallyreduce. Backwash when the pres-sure gauge increases 5 to 7 poundsabove the clean filter starting pres-sure. Normal backwash duration is1-1/2 to 2 minutes or until water runsclear.

VACUUMING YOUR POOLWhen vacuuming your pool, the filtermust work harder. Consequently, allof that debris is caught in the filter ata very rapid rate. This causes a rapidincrease in filter pressure as will be

BACKWASH: Backwashing reversesthe flow of water through the filter toflush out the dirt and debris, andwaste water is discharged to wastefrom the valve body port with sightglass.

FILTER TO WASTE: Place the valvein the “Filter to waste” position afterbackwashing your filter. (Normally,for only 10 seconds.)

PUMP TO WASTE: This positionallows you to vacuum heavy debrisor larger amounts of settled contami-nants from the pool floor directly towaste.

RECIRCULATE POSITION: Thisposition allows you to increase thewater flow rate to circulate chemicalsthroughout the pool more quickly.Pool water passes through the valveon top of the filter bypassing internalfilter components and travels back tothe pool at a rapid rate.

WINTERIZE POSITION : This posi-tion allows you to drain trapped waterfrom the filter valve and relievecompression on the rotor valvegasket during winter storage.

CLOSED POSITION : When servicingthe filter, place the valve in the“Closed” position to stop backflow ofwater from pump. Stuff rag in returnfitting.

INITIAL START UPBefore you begin filtering your pool,the filter sand must be backwashedthoroughly to remove the extra finesand grains normally found in newfilter sand.

1. Loosen the pump strainer pot lidto allow air to escape. Tighten lidwhen water begins to flowbetween strainer pot lid andstrainer body. Do not overtighten.

2. Plug in your pump to the GFCIprotected receptacle. Refer toWARNINGS.

3. Push down on the valve handleand rotate to the BACKWASHposition. Make sure valve handleindexes into the alignment slotson valve.

4. Start pump. During this initialstart-up allow 4-5 minutes toflush out the super-fine sandgrains to prevent them from

ELECTRICAL OUTLETRefer to your pump owners guide fordetailed information pertaining to therequirements and regulations for safeelectrical installation of the powersupply, receptacle outlet, switchingand ground fault interrupter.

FINISH FILLING POOLFinish filling your pool, referring toskimmer installation and pool assem-bly instructions for proper water level.

VALVE OPERATIONYour new filter has seven positions ofoperation, which are explained below.To change positions of the valve,make sure the pump is OFF. Pressdown on the valve handle enough tofree the locking tab. Rotate thehandle so the tab LOCKS in thedesired position.

FILTER: Normal pool filteringposition. May also be used whenvacuuming the pool.

7

CAUTIONBEFORE removing filter or pumpfrom pool for servicing, prevent thebackflow of water from your skimmerand return inlet from flowing out ofdisconnected hoses.

1. Remove skimmer cover andbasket and plug inside bottomhole with rag.

2. Referring to the instructions foryour return inlet, remove the inletcover and eye ball. Insert thewinterizing disc and reinstall thecover.

3. Disconnect hoses on filter orpump as necessary whenremoving for service orrepairs.

DRAIN TANKSee Caution Above

1. Turn clamp screws counter-clockwise to loosen clamp.Remove clamp, valve and o-ring.

2. Remove tank drain cap to drain.

3. Place plastic bag over riser tubein tank and secure with a rubberband. Scoop out sand with amedium size can and place inplastic bag.

4. After servicing, reassemble andinstall in reverse. Make sure tanko-ring and sealing areas are freeof any sand grains.

WINTERIZING FILTERIn areas subject to freezing damage,it is mandatory that the filter, pumpand any related components beremoved from the pool and storedindoors. (Refer to individual compo-nents owners guide such as pump,skimmer, chlorinator, etc., for specificwinterizing instructions.)

1. Backwash the filter.

2. Syphon pool water level downbelow skimmer opening by usingyour vacuum hose and allowwater to flow to an area that canaccept a couple of thousandgallons or more.

3. Turn clamp screws counter-clockwise to loosen clamp.Remove clamp, valve and o-ring.

4. Remove tank drain cap and allowtank to drain fully.

indicated on the pressure gauge.Frequent backwashing will benecessary during this processdepending on the amount of sedi-ment being vacuumed off the poolfloor. Keep a check on the poolwater level and refill as required.

MAINTENANCEPreventative maintenance willprovide continued smoothperformance and extend the life ofyour filter for many years. Neglectwill cause parts to wear or bind,leaks to occur and result in costlyrepairs. Keep moving parts lubri-cated and a clean environmentaround your filter and related compo-nents.

LUBRICATIONThere are various types of lubricantsavailable. However, most are in-tended for moving metal parts.Unfortunately, these lubricants willharm or degrade plastics. DO NOTuse petroleum base lubricants. Manypeople consider “PETROLEUMJELLY” safe for babies, and can beapplied to anything. But, it willDESTROY most plastics and o-ringseals. Silicone lubricants are avail-able at your pool dealer, and are safefor use on plastics and o-rings.

LUBE VALVE SHAFTTo lubricate the o-ring on the valveshaft, depress valve handle fully andapply silicone lubricant on the shaftbetween handle and valve cover.Then, rotate handle to distributelubricant. Resume normal filteroperation by rotating handle to theFilter position and start pump.

REPAIRSServicing should be performed by aqualified dealer. If disassembly isattempted, mark each of the partsassembled position as it relates to itsmating parts. This assures properalignment when reassembled.Malfunction will occur if not properlyassembled. See your dealer fororiginal replacement parts.

5. Disconnect all hoses.

6. Place plastic bag over riser tubein tank and secure with a rubberband. Scoop sand out with amedium size can and place inplastic bag. If sand is not badlycontaminated, save for nextseason.

7. Store all components in a warmdry area indoors.

DAMAGE CAUSED BYFREEZING TEMPERATURES ISNOT COVERED BY PRODUCT

WARRANTY.

NEW FILTER START UP

AFTER ADDING THE CORRECT

SAND, #20 grade filter (.4/.5

mm) sand, AND CORRECT

AMOUNT.

BACKWASH FILTER PRIOR TO

RUNNING IN FILTER POSITION.

THIS WILL CLEAN THE SAND AND

ELIMINATE FINE SAND

PARTICLES FROM ENTERING

POOL AND PLUGGING UP

UNDERDRAIN SLOTS. AFTER

BACKWASHING, RUN IN FILTER

TO WASTE FOR APPROX. 30

SECONDS TO FLUSH FILTER.

NOW THE UNIT IS READY FOR

NORMAL FILTERING OPERATION.

8

Exploded View AquaView Model 014 & 017Doughboy Sand Filter with 7 Position Valve

TO WASTE

TO TOPPUMP PORT

TO POOLRETURN

TO FRONTPUMP PORT

TO SKIMMER

9

Parts List AquaView Model 014 & 017Doughboy Sand Filter with 7 Position ValveITEM PART # QTY DESCRIPTION *1 1121-1970 1 Tank w/Decals - 014 Model

1121-1971 1 Tank w/Decals - 017 Model2 1107-1636 1 Underdrain Base Assembly

**3 1107-1679 1 Underdrain Assembly - 014 Model1121-1855 1 Underdrain Assembly - 017 Model

4 330-1023 4 #8 x 5/8" Screw5 308-1280 1 Valve O-Ring

5a 308-1282 1 Square O-ring6 330-1260 2 1/4-20 x 1-1/2" Mach. Screw7 340-2281 2 Tank Clamp8 395-1014 1 2" Pressure Gauge9 340-1951 2 1-1/2" Hose Adaptor

10 1107-2468 1 Valve Assembly w/decal11 387-1017 6 1-1/2" Hose Clamp12 340-1892 1 1-1/2" Elbow Hose Adaptor13 346-1077-1 2 1-1/2" x 8' Hose14 321-1082 2 1/4-20 Hex Nut15 346-1076-1 1 1-1/2" x 32" Hose16 340-2200 1 Drain Screen17 307-1001 1 Drain Cap Gasket18 340-2445 1 Drain Cap19 308-1225 1 5/16" Thread Seal20 330-1245 1 5/16-18 x 1-1/4" Bolt21 340-2444 1 Combo filter base22 368-1074 1 Warranty Card

* Item 1 includes items 16, 17, and 18.**Item 3 includes items 2 and 4.

ITEM PART # QTY DESCRIPTION23 1121-1622 1 Valve Handle24 1121-1623 1 Handle Pin25 1121-1624 1 Washer - Large26 1121-1626 1 Cover27 1121-1627 1 O-ring - #25228 1121-1628 1 Washer - Small29 1121-1629 1 Spring30 1121-1630 2 O-ring Diverter31 1121-1631 1 Diverter32 1121-1632 1 Spider Gasket33 1121-1633 1 Valve Body34 1121-1636 1 Sight Glass35 1121-1635 1 Sight Glass Gasket36 1121-1634 6 Nut37 1121-1625 6 Screw - M6 x 30mm38 1121-1701 1 O-ring - #22539 360-1764 1 Valve Decal (not shown)

VALVE ASSEMBLY

10

Exploded View AquaView Model 020 and Model 024Doughboy Sand Filter with 7 Position Valve

TO WASTE TO POOLRETURN

TO TOPPUMP PORT

TO FRONTPUMP PORT

TO SKIMMER

WARRANTY CARD

OWNER'S GUIDE

11

Parts List AquaView Model 020 and Model 024Doughboy Sand Filter with 7 Position Valve

*1 1121-1972 1 Tank w/Decals Model - 0201121-1973 1 Tank w/Decals Model - 024

2 340-2224 1 Underdrain Spacer3 1107-1649 1 Threaded Underdrain Assembly

4 330-1023 8 #8 x 5/8" Screw5 1121-1543 1 Tank Internal Adaptor w/Insert & Screws6 308-1225 1 5/16" Thread Seal7 330-1245 1 5/16-18 x 1-1/4" Bolt8 340-2444 1 Tank Base9 340-2445 1 Drain Cap

10 307-1001 1 Drain Cap Gasket11 340-2200 1 Sand Filter Drain Screen

**12 1107-2431 1 Underdrain Assembly Model - 0201121-1858 1 Underdrain Assembly Model - 024

13 330-1260 2 1/4-20 x 1-1/2" Mach. Screw14 321-1082 2 1/4-20 Hex Nut15 340-2281 2 Tank Clamp16 308-1282 1 Square O-Ring

16a 308-1280 1 Valve O-ring17 395-1014 1 2" Pressure Gauge18 340-1951 2 1-1/2" Hose Adaptor19 1107-2468 1 Valve Assembly w/Decal20 387-1017 6 1-1/2" Hose Clamp21 346-1077-1 2 1-1/2" x 8' Hose22 340-1892 1 1-1/2" Hose Elbow23 346-1076-1 1 1-1/2" x 32" Hose24 368-1074 1 Warranty Card25 365-1993 1 Owner's Guide

* Includes items 9, 10, and 11.

**Item12 includes items 2, 3 and 4

ITEM PART # QTY DESCRIPTION

ITEM PART # QTY DESCRIPTION

26 1121-1625 6 Screw - M6 x 30mm27 1121-1622 1 Valve Handle28 1121-1623 1 Handle Pin29 1121-1624 1 Washer - Large30 1121-1626 1 Cover31 1121-1627 1 O-ring - #25232 1121-1628 1 Washer - Small33 1121-1629 1 Spring34 1121-1630 2 O-ring Diverter35 1121-1631 1 Diverter36 1121-1632 1 Spider Gasket37 1121-1633 1 Valve Body38 1121-1636 1 Sight Glass39 1121-1635 1 Sight Glass Gasket40 1121-1634 6 Nut - M641 1121-1701 1 O-ring - #22542 360-1764 1 Valve Decal (not shown)

VALVE ASSEMBLY

12

Change of Design: Doughboy Recreational expressly reserves the right to change or modify the design and constructionof any product in due course of our manufacturing procedures, without incurring any obligation or liability to furnish or installsuch changes or modifications on products previously or subsequently sold.

Doughboy Recreational 315 N. Sebastian St. • West Helena, AR 72390 Visit our website at www.doughboy-pools.com

DB 0606-273-1 Made in the United States of America Copyright © 2006

TROUBLESHOOTING SAND FILTERS

PROBLEMS POSSIBLE CAUSE REMEDIES

1 - Backwash filter.2 - Backwash filter

3 - Use #20 filter sand.4 - Replace sand.

1 - Fill pool so water is betweenmarks on skimmer face plate.

2 - Clear obstruction in skimmer,hoses or pump.

3 - Clean skimmer and strainerbaskets.

1 - Check with test kit or contactdealer.

2 - Use #20 filter sand.3 - Use crushed #20 filter sand.

1 - Check chemical balance.Filter will require frequentbackwashing.

2 - Backwash filter thoroughly.Waste hose too long orrestricted.

3 - Replace sand with #20 filtersand.

1 - Replace underdrain.2 - Use #20 filter sand.

1 - Actuate valve handle andmake sure valve is seated.

2 - Replace gasket or contactdealer.

Note: Contact your pool dealerfor any problems youcannot solve.

1 - High gauge pressure, low returnflow

2 - Low gauge pressure, low flow.Pump sucking in air. Pumpsounds like marbles rattling in it.

3 - High flow, low or normal gaugepressure but pool water will notclear up.

4 - Short filter cycles.

5 - Sand entering pool.

6 - Water leaking to waste.

1 - Insufficient backwashing.2 - Excessive contaminants or

algae in sand.3 - Filter sand is too fine.4 - Underdrain plugged.

1 - Water level too low in pool.

2 - Restriction on suction side ofpump.

3 - Skimmer or strainer basketfilled with debris.

1 - Pool water is chemically outof balance.

2 - Sand too coarse.3 - Sand grains rounded or

worn.

1 - Excessive contaminants oralgae in sand or pool.

2 - Improper backwashing.

3 - Sand too fine.

1 - Defective underdrain.2 - Sand too fine.

1 - Valve not seated in filterposition.

2 - Defective gasket in valvebody.