INSTALLATION INSTRUCTIONS FOR PART 99-3306

99-3306

APPLICATIONS

Chevrolet Aveo 2007

KIT FEATURES

• DIN Mount Radio Provision with Pocket• ISO Mount Radio Provision with Pocket• Double DIN Mount Radio Provision• Stacked ISO Units Provision

A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets • E) Double DIN Trim Plate • F) Pocket

KIT COMPONENTS

A

TOOLS REQUIRED:Small Flat Blade Screwdriver/ Panel Removal Tool

• Phillips Screwdriver • Socket Set

1-800-221-0932 © COPYRIGHT 2004-07 METRA ELECTRONICS CORPORATION

www.metraonline.com

B

DE

C

F

Pontiac G3 2007

Dash Disassembly- Chevrolet Aveo 2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1- Pontiac G3 2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Kit Assembly- DIN Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . 2- ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . 3- Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4- Stacked ISO Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

TABLE OF CONTENTS

99-3306

*Note: Refer also to the instructions included with the aftermarket radio.

99-3306 DASH DISASSEMBLY

CHEVROLET AVEO 2007

A

1

1

2

23

3 4

4

5 6

SOUND SCAN AST

A/C

1 2 3 4 5 6

SOUND SCAN AST

A/C

B

1

1

Remove (4) 9/32” screws securingthe radio. Unplug and remove radio.(Figure B)

Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.

3

Unclip and remove trim panel aroundradio. (Figure A)

2

Continue to kit assembly.

PONTIAC G3 2007

99-3306 KIT ASSEMBLY

2

A

B

C

DIN MOUNT RADIO PROVISION WITH POCKET

Slide the DIN cage into the RadioHousing and secure by bending themetal locking outward. (Figure A)

1

Slide the aftermarket radio into the DINcage until it snaps into place. (Figure B)

2

Snap the pocket into the radio housing.(Figure C)

3

Continue to final assembly.

*Note: Refer also to the instructions included with the aftermarket radio.

99-3306 KIT ASSEMBLY

3

A

B

C

ISO MOUNT RADIO PROVISION WITH POCKET

Mount the ISO Brackets to the radiousing the screws supplied with theradio. (Figure A)

1

Slide the radio into the radio openinguntil it snaps into place. (Figure B)

2

Snap the ISO Trim Plate onto the frontof the Radio Housing. (Figure B)

3

Snap the pocket into the radio hous-ing. (Figure C)

4

Continue to final assembly.

*Note: Refer also to the instructions included with the aftermarket radio.

99-3306 KIT ASSEMBLY

4

DOUBLE DIN MOUNT RADIO PROVISION

Cut and remove the center bar fromthe radio housing. (Figure A)

1

Snap the Double DIN brackets to theinside edge of the radio housing.(Figure B)

2

Slide the Double DIN radio into thebracket/radio housing assembly andsecure the radio to the assembly usingthe screws supplied with the radio.(Figure C)

3

Snap the Double DIN trim-plate ontothe front of the housing/radio assem-bly. (Figure C)

4

Continue to final assembly.

*Note: Refer also to the instructions included with the aftermarket radio.

A

B

C

99-3306 KIT ASSEMBLY

5

STACKED ISO UNITS PROVISION

Cut and remove the center bar fromthe radio housing. (Figure A)

1

Snap the Double DIN brackets to theinside edge of the radio housing.(Figure B)

2

Slide the stacked ISO units into thebracket/radio housing assembly andsecure the units to the assembly usingthe screws supplied with the units.(Figure C)

3

Continue to final assembly.

*Note: Refer also to the instructions included with the aftermarket radio.

A

B

CD

Snap the Double DIN trim-plate ontothe front of the housing/radio assem-bly. (Figure D)

4

99-3306 FINAL ASSEMBLY

FINAL ASSEMBLY

(A) Strip wire ends back 1/2"

B) Twist ends together

C) Solder

D) Tape

A

B

C

D

Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ-ually tape off the ends of any unused wires to prevent electrical short circuit.)

Re-connect the negative battery terminal and test the unit for proper operation.

Reassemble radio and dash assemblies in reverse order of disassembly.

1

2

3

FINAL WIRING CONNECTIONS

Make wiring connections using the EIA color code chart shown below and the instructions included with thehead unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and

individually tape off ends of any unused wires to prevent electrical short circuit.

METRA / EIA WIRING CODE

12V Ignition / Acc . . . . . . . . . . Red

12V Batt / Memory. . . . . . . . . Yellow

Ground. . . . . . . . . . . . . . . . . . Black*

Power Antenna. . . . . . . . . . . . Blue

Amp Turn-On . . . . . . . . . . . . . Blue / White

Amp Ground. . . . . . . . . . . . . . Black / White

Illumination . . . . . . . . . . . . . . Orange

Dimmer . . . . . . . . . . . . . . . . . Orange / White

Right Front (+) . . . . . . . . . . . . Gray

Right Front (-). . . . . . . . . . . . . Gray/ Black

Left Front (+) . . . . . . . . . . . . . White

Left Front (-). . . . . . . . . . . . . . White / Black

Right Rear (+) . . . . . . . . . . . . Violet

Right Rear (-) . . . . . . . . . . . . . Violet / Black

Left Rear (+) . . . . . . . . . . . . . Green

Left Rear (-) . . . . . . . . . . . . . . Green / Black

*NOTE: When a Black wire is not present, ground radio to vehicle chassis.All colors may not be present on all leads due to manufacturer’s specifications.

6

NOTES

7

99-3306

NOTES

8

99-3306

NOTES

9

99-3306

99-3306 INSTRUCTIONS

1-800-221-0932 REV. 06/21/07 © COPYRIGHT 2004-07 METRA ELECTRONICS CORPORATION INST99-3306

www.metraonline.com