Apollo Tech

Technical Data for:

Apollo Valves

How to Order Apollo Valves

Bronze Ball Valves

Two Piece Ball Valves

Three Piece Ball Valves

Three Way Valves

Union End Valves

Steam Prep Ball Valves

ANSI Flanged Ball Valves

Specialty Ball Valves

Top Entry Valves

Optional Configurations

Engineering Data

VARIATIONS1 One Size Larger Male Retainer2 Adjustable Stop Lever3 Cu-Ni Ball & Stem4 SS Sall & Stem5 Original Balancing Stop- Attach to Lever or T-Handle7 One Size Smaller Female Retainer8 (Not Assigned)9 Pinned Retainer

-01 Standard-02 Stem Grounded-03 1-1/4" Carbon Steel Ext.Stem-04 2-1/4" Carbon Steel Ext.Stem-05 Plain Ball-06 2000 lb. 73-100 Series (1-1/4" to 2")-07 Steel Tee Handle-08 90 degree reversed stem-09 SS Lever-10 SS Lever & Nut-12 Stamp “157 SWP” & Bagged-13 Stamp “157 SWP”-14 Side Vented Ball (uni-directional)-15 Wheel Handle, Steel-16 Chain Lever, Vertical-17 Rough Chrome Plate - Bronze Valves-21 UHMWPE Trim (non-PTFE)-22 Viton Union Seals-23 Tank Flange (2" 3-pc valves only)-24 Graphite Packing-25 Graphite Packing, Vented Ball & Tack Welded Ret.-26 Chevron Pkg Vent Assd.Dry Monel Trim (7A)-27 SS Latch Lock Lever & Nut-28 Actuator Mounting Pad Not Drilled/Tapped-29 Graphite Packing & Seals-30 Cam-Lock and Grounded Stem-31 7B Series w/Boss not Drilled/Tapped-32 SS Hi-Rise Tee Handle & Nut-33 76-300 Series w/Pad Drilled/Tapped-34 Nylatron Seats (96 Series)-35 VTFE Trim-36 SS HiRise Round Handle, SS Nut-38 Peek Seats & Bearing (Graphite packing & seals)-39 SS Hi-Rise Locking Wheel Handle, SS Nut-40 Cyl-loc and Grounded Stem-41 Auto.Drain (Bronze Valves Only)-42 Non-Vented Ball, No Holes in Slot (CS and SS)-43 Cyl-Loc, Grnd B&S, 680 LocTite or 2-Tack Welds-44 Seal Weld 76-100 & 89-100-45 Less Lever & Nut

MATERIALS OR STYLE70 Bronze71 Bronze with pads72 Carbon Steel, High Pressure73 Carbon Steel73A A105 Carbon Steel74 Nickel75 Pad-Locking Bronze76 CF8M Stainless Steel76F CF8M Stainless Steel, Full Port77 Bronze Full Port77C Bronze Full Port Economy78 Special Valves79 Refrigerant Valves7A Chlorine Carbon Steel7K Bronze Full Port Drain80 Bronze, UL Listed81 Bronze UL Listed Plain Ball82 Bronze 3-Piece Full Port83 CS 3-Piece83R CS 3-Piece, Actuator Ready85 SS 3-Piece, Reg.Port85R SS 3-Piece, Reg.Port, Actuator Ready86 SS 3-Piece, Full Port86R SS 3-Piece, Full Port, Actuator Ready87 CF8M SS Flanged87A CF8M SS Flanged87A-400 Alloy-20 Flanged88 Carbon Steel Flanged88A Carbon Steel Flanged89 Cast Carbon Steel w/Pads9A Bronze, Hvy.Patt. Unibody90 Bronze, Unibody, UL Listed91 Bronze, Unibody92 Cast Carbon Steel Unibody93 CS Unibody95 Bronze Stop & Drain96 CF8M SS Unibody399 Alloy-20 NPT401 Alloy-20, 3-Piece, Full Port

-46 SS Latch Lock Lever, Lock in Closed Position Only-47 SS Oval Latch Lock Handle, SS Nut-48 SS Oval Handle, No Latch, SS Nut-49 Assembled Dry-50 2-1/4" CS Locking Stem Extension-51 One Tack Weld (I-7362-05-1X)-52 Two Tack Weld (I-7362-05-2X)-53 Three Tack Weld (I-7362-05-3X)-54 Four Tack Weld (I-7362-05-4X)-56 MultiFill Seats and Packing-57 Oxygen Cleaned (Bronze and SS Only)-58 Chain Lever, Horizontal-59 SS External Trim – 3-pc Valves-60 Grounded Ball & Stem-61 Grounded Ball & Stem, Assembled Dry-62 Body Centre Section-63 NPT x Solder/Socket Weld-64 250 lb. Steam Trim-65 MultiFill Seats & Graphite Packing-66 FNPT x Butt Weld-68 4" Stem Extension (3" & 4" 3-pc. 82 Series-69 Purge Ports Drilled/Tapped @ Bottom & approx. 45" from Top-70 4" Extended Bonnet-72 RTFE Packing-73 TFE Packing - Spiral Wound Body Seals - TFE Fillers - Flange BV-74 Graphite Packing - Spiral Wound Body Seals - Graphoil Fillers - Flange BV-75 MPTFE Seats, PTFE Packing, RPTFE Gaskets-76 Live Loaded 87A/88A Series (Lever)-77 Live Loaded 87A/88A Series (Gear & Actuated)-78 Delrin Seats-79 Nylon Seats/Graphite Packing 72 Series-80 Multi-Seal (Super TFE) 87A/88A Series-97 Grnd.Whl.Handle, Pinned or Tack Welded-98 Grnd.Whl. Pinned or Tack Welded & 1-1/4" Stem Ext.-SW Limit Switch Mounted-MG Gear Operated, Std. Hand Wheel-MH Gear Operated, Std. Hand Wheel, Lockout Device-MJ Gear Operated, Oversize Hand Wheel-MK Gear Operated, Oversize Hand Wheel, Lockout Device-P01 BSPP (Parallel) Thread Connection-BC Ball CheckT01 BSPT (Tapered) Thread Connection

DESIGN

TYPE1 NPT Female/150 Flange2 Solder & Soc. Weld/150 Flange Full Port3 Union End NPT/Reg.Port Soc.Weld4 Union End Solder/Reg.Port Soc.Weld5 Spring Return/High Pressure Full Port NPT6 3-way, NPT/High Pressure Soc.Weld Full Port7 Butt Weld/300 Flange8 Male x Female, NPT/600 Flange9 3-way Solder/O-Ring Boss/300 Flange Full Port

SIZE1 1/4"2 3/8"3 ½"4 3/4"5 1"6 1 1/4"7 1 ½"8 2"9 2 ½"0 3"A 4 "C 6"E 8"G 10"H 12"

Apollo Numbering System PLEASE USE ALL D IGITS WHEN ORDERING

0 0 - 0 0 0 - 0 0

Cam Morton

Cam Morton

Cam Morton

Cam Morton

Cam Morton

Cam Morton

Cam Morton

Cam Morton

Cam Morton

Cam Morton

Cam Morton

Cam Morton

4

Ball Valves

Customer Service 1-704-841-6000

Model Size Dimensions (In.) Wt.Number (In.) A B C D E F G H I J K L M Cv (Lbs) -0177C-101 1/4 0.37 0.95 1.97 1.76 3.74 1.86 4.06 1.41 3.50 2.80 3.12 4.12 3.86 4.5 0.677C-102 3/8 0.37 1.07 2.09 1.76 3.74 1.86 4.06 1.41 3.50 2.80 3.12 4.12 3.86 7.2 0.677C-103 1/2 0.50 1.15 2.25 1.79 3.74 1.89 4.06 1.44 3.50 2.83 3.12 4.12 3.89 15.5 0.677C-104 3/4 0.75 1.32 2.65 2.00 4.88 2.20 5.03 1.76 4.00 3.12 3.12 4.12 4.10 35.6 1.177C-105 1 1.00 1.53 3.07 2.19 4.88 2.39 5.03 1.96 4.00 3.32 3.12 4.12 4.29 68.1 1.877C-106 1-1/4 1.25 2.04 4.08 3.13 7.06 3.76 7.19 2.82 6.00 - - - 5.23 125.0 4.477C-107 1-1/2 1.50 2.21 4.43 3.29 7.06 3.92 7.19 2.98 6.00 - - - 5.39 177.0 5.977C-108 2 2.00 2.76 5.29 3.83 7.06 4.46 7.19 3.52 6.00 - - - 5.93 389.0 11.4

77C-202 3/8 0.37 0.93 1.84 1.76 3.74 1.86 4.06 1.41 3.50 2.80 3.12 4.12 3.86 7.2 0.677C-203 1/2 0.50 1.15 2.31 1.79 3.74 1.89 4.06 1.44 3.50 2.83 3.12 4.12 3.89 15.5 0.677C-204 3/4 0.75 1.39 2.79 2.00 4.88 2.20 5.03 1.76 4.00 3.12 3.12 4.12 4.10 35.6 1.077C-205 1 1.00 1.69 3.38 2.19 4.88 2.39 5.03 1.96 4.00 3.32 3.12 4.12 4.29 68.1 1.677C-206 1-1/4 1.25 2.08 4.16 3.13 7.06 3.76 7.19 2.82 6.00 - - - 5.23 125.0 3.977C-207 1-1/2 1.50 2.33 4.66 3.29 7.06 3.92 7.19 2.98 6.00 - - - 5.39 177.0 5.877C-208 2 2.00 2.95 5.84 3.83 7.06 4.46 7.19 3.52 6.00 - - - 5.93 389.0 10.2

Apollo® 77C: The Contractors’ Full-Port Bronze Ball Valve

77C-100 & 77C-200

Full Port Bronze Ball Valve with Solid Ball

Apollo’s® solid ball design delivers real full-port performance.

Some valve manufacturers use a hollow ball in their “full-port” ball valves. A hollow ball creates turbulence inside thevalve which causes significant drops in pressure and velocity. Plus, the media bouncing around inside the ball addsunnecessary stress to the valve and the system, leading to even more problems down the line.

Get solid full-port performance at an affordable price with the American-made Apollo 77C.

77C-100

77C-200

• Machined solid chrome-plated ball• Multi-fill PTFE seats and seals• Adjustable packing• Blow-out proof stem design• American-made bronze castings• Vacuum service to 29 in. Hg

• Full-port design through 2”• Available with stainless steel ball and stem as

77C-140 Series • ANSI B16.18 solder end version available as

77C-200 Series

5

Ball Valves


Model Size Dimensions (In.)Number (In.) A B C D E32-101-01 1/4 0.37 0.80 1.60 1.65 2.8732-102-01 3/8 0.37 0.80 1.60 1.65 2.8732-103-01 1/2 0.40 1.00 2.00 1.68 2.8732-104-01 3/4 0.65 1.20 2.41 1.90 3.8732-105-01 1 0.75 1.55 3.09 2.18 4.8732-106-01 1-1/4 1.00 1.72 3.44 2.53 5.5032-107-01 1-1/2 1.12 1.93 3.87 2.69 5.5032-108-01 2 1.50 2.17 4.37 2.94 5.50

Model Size Dimensions (In.)Number (In.) A B C D E32-203-01 1/2 0.40 1.29 2.65 1.68 2.8732-204-01 3/4 0.65 1.73 3.56 1.90 3.8732-205-01 1 0.75 2.11 4.26 2.18 4.8732-206-01 1-1/4 1.00 2.36 4.60 2.53 5.5032-207-01 1-1/2 1.12 2.84 5.42 2.69 5.5032-208-01 2 1.50 3.33 6.48 2.94 5.50

Reduced Port Solder End Bronze ValveSolder end ball valve with vacuum service to 29" Hg. Rating of 400 psig WOG cold, non-shock and 125 psig for satu-rated steam. Blowout-proof stem design with adjustable packing gland.

32-100-01

32-200-01

Reduced Port Threaded Bronze Ball Valve NPT threaded ball valve rated to 400 psig WOG cold, non-shock and 125 psig for saturated steam. Blowout-proofstem design with adjustable packing gland.

• Chromium plated ball• PTFE seats and RPTFE stuffing box ring

Reduced Port Economy Valves

6

Ball Valves


• Rated 600 psig WOG, cold, non-shock• 150 psig for saturated steam

General Purpose Standard Port Valves

70-100-01 Standard Port Threaded Ball ValveThis Conbraco general purpose valve is the most widely used bronze ball valve in the industry. Like all 70Series valves, it features a blowout-proof stem, RPTFE seats and stuffing box ring, adjustable packing glandand chromium-plated ball.

*Body only. Total will vary with handle and end connection options. ContactConbraco Customer Service for these dimensions.All 70-100 Series valves are available in sizes 1/4" through 4".✝ High capacity water valve, formerly 78-255-01

Model Size Dimensions* (In.)Number (In.) A B C70-101 1/4 0.37 1.03 2.06

70-102 3/8 0.37 1.03 2.06

70-103 1/2 0.50 1.12 2.25

70-104 3/4 0.68 1.50 3.00

70-105 1 0.87 1.68 3.37

70-106 1-1/4 1.00 2.00 4.00

70-107 1-1/2 1.25 2.18 4.37

70-108 2 1.50 2.34 4.68

70-109 2-1/2 2.00 3.12 6.25

70-100 3 2.50 3.37 6.75

70-10A✝ 4 3.12 3.68 7.37

70-100-03/04 Standard Ball Valve with Stem ExtensionIdeal for hydronic or low pressure steam applications, this valve features a stem extension to accommodateinsulation or to relocate handle position. This ball valve is equipped with chromium-plated ball, RPTFE seatsand stuffing box ring, a blowout-proof stem design and adjustable packing gland.

• Rated 600 psig WOG, cold, non-shock• 150 psig for saturated steam• Specify -03 for 1-1⁄4” extension, -04 for 2-1⁄4” extension

Ball Valves

Chain Lever Ball ValvesReliable quarter turn operation in overhead

applications. A favorite for usein industrial environments.Standard design featuresinclude blowout-proof stem andRPTFE seats and seals.

• Specify suffix -16 for assembly with valve in vertical position

• Specify -58 for valve in horizontal position

Threaded Valve with Tee HandleTee handle is ideal when space is limited and

where safety is a consideration.Handle still provides visual indica-tion of OPEN or CLOSED position.Valve features a chromium-platedball, RPTFE seats and stuffing boxring, a blowout-proof stem designand adjustable packing gland.

• Rated 600 psig WOG, cold, non-shock

• 150 psig for saturated steam

Threaded Ball Valve with 90° ReversedStem

Use in critical applicationswhen handle is required tobe in a parallel positionwhen closed. Featureschromium-plated ball,

RPTFE seats and stuffing box ring. Rated600 psig WOG, cold, non-shock; 150 psig forsaturated steam.

• Blowout-proof stem design • Adjustable packing gland

Threaded Valve with Rough Chrome PlatingUse where a clean environment is required;

for matching up withother chrome-platedequipment. Featuresa chromium-platedball, RPTFE seatsand stuffing box

ring, a blowout-proof stem design andadjustable packing gland.


Threaded Ball Valve with Cam-Lock HandlePatented Cam-Lock® handle gives valve

extra protection against accidentaloperation. Reliable quarter-turn shut-off from a versatile, ruggedly builtvalve.

• RPTFE seats and stuffing box ring • Rated 600 psig WOG, cold,

non-shock

Ball Valve with Threaded and SolderEndsEliminates need forspecial pipe connec-tor when connectingto different pipe

such as iron pipe or copper tubing. Valveoffers reliable shut-off and easy quarter-turn operation; ruggedly built with achromium-plated ball, a blowout-proofstem design and RPTFE seats and stuff-ing box ring.

• 150 psig for saturated steam• Rated 600 psig WOG, cold, non-shock

Threaded Ball Valve with Latch LockSliding lock mechanism secures handle in

open or closed position.Valve can also be pad-locked open or closed.Valve features blowoutproof stem, RPTFE seats

and stuffing box ring, chrome plated balland adjustable packing gland.

• 600 psig WOG, cold, non-shock• 150 psig for saturated steam• Available with auto drain option for

pneumatic applications. Use the follow-ing suffix key to specify latch lock valvewith auto drain option: -27 -41

Ball Valve with Automatic DrainWhen this valve is shut off for maintenance

of pneumatic tool, pres-sure from valve to tool isautomatically drained toatmosphere to preventaccidential operation of

the tool, causing possible injury.

• Conforms to certain OSHA requirementsin pneumatic installations

• Easy, safe maintenance of pneumatictools

• Cannot be used where drained mediacould cause damage

• Temperature range = 50°F to 200°F• Rated 125 psig air or water• Available with latch lock option,

specify -27 -41 suffix

70-100-16/58 70-100-07

70-100-08 70-100-17

70-100-27 70-100-41

70-100-30 70-100-63


8

Ball Valves



Ball Valve With Single Union End This valve combines pipe union with ball valve shut-off; it saves time and labor by eliminating the need for extraconnections. Viton O-Ring sealed union requires light torque for proper seal.

• Chromium-plated ball• Blowout-proof stem design • Adjustable packing gland

70-300-01

• Vacuum service to 29” Hg• Adjustable packing gland

• RPTFE seats and stuffing box ring

70-200-01 Solder End Ball ValveReliable ball valves designed for soft-soldering into lines without the need for disassembly. Tested valve installswithout disturbing seats and seals. Soldering temperature: 500°F or less.

*Based on 70-200-01 – Dimensions may vary with options.Contact Conbraco customer service for dimensions on 70-200-63.

Model Size Dimensions (In.)Number (In.)* A B C D E F G70-202 3/8 0.37 1.28 2.56 1.75 3.87 0.505 0.3770-203 1/2 0.50 1.43 2.87 1.75 3.87 0.63 0.5070-204 3/4 0.68 1.93 3.87 2.12 4.87 0.88 0.7570-205 1 0.87 2.25 4.50 2.25 4.87 1.13 0.9070-206 1-1/4 1.00 2.31 4.62 2.62 5.50 1.38 0.9670-207 1-1/2 1.25 2.62 5.25 3.06 8.00 1.63 1.0970-208 2 1.50 3.18 6.37 3.25 8.00 2.13 1.3470-209 2-1/2 2.00 3.74 7.51 3.72 8.00 2.63 1.4870-200 3 2.50 4.12 8.25 4.12 8.00 3.13 1.67

9

Ball Valves


Model Size Dimensions (In.)Number (In.) A B C D E70-801-01 1/4 0.37 1.40 2.43 1.75 3.8770-802-01 3/8 0.37 1.46 2.50 1.75 3.8770-803-01 1/2 0.50 1.68 2.81 1.81 3.8770-804-01 3/4 0.68 2.00 3.50 2.12 4.8770-805-01 1 0.87 2.31 4.00 2.25 4.8770-806-01 1-1/4 1.00 2.31 4.31 2.62 5.5070-807-01 1-1/2 1.25 3.00 5.18 3.06 8.00

70-800-01 Male x Female NPT Ball Valve Eliminates need for extra nipple when connecting to female connection to save time and labor. Ruggedly built for last-ing performance with chromium-plated ball and blowout-proof stem design.

• Vacuum service to 29" Hg.• RPTFE seats and stuffing box ring

E

D

A

B

C

Model Dimensions (In.)Number A B C D E F G H Wt.78-124-01 0.50 1.26 2.52 2.27 3.53 1.12 10-24 1.40 1.0678-125-01A 0.75 1.53 3.12 2.87 3.87 1.53 1/4-20 1.98 2.64

78-124-01 &78-125-01A

5-Port Tank Selector Ball ValvePerfect for fuel tank selection on large marine vessels, or in any application requiring control of multiple mediathrough a single valve. Five-port construction allows access to four different tanks using only one valve. Unique balldesign allows for higher flow capacities. Designed for easy installation and mounting.

• Bronze with stainless steel lever and nut • 50 psig pressure rating• Pointer on handle indicates selected inlet

5-Port Valves

10

Ball Valves


Model Size Dimensions (In.)Number (In.) A B C D E F G H I70-601-01 1/4 0.37 1.12 2.32 1.80 3.88 1.18 0.875 1.37 10-2470-602-01 3/8 0.37 1.12 2.32 1.80 3.88 1.18 0.875 1.37 10-2470-603-01 1/2 0.50 1.09 2.25 1.75 3.87 1.18 0.87 1.37 10-2470-604-01 3/4 0.68 1.50 3.00 2.12 4.87 1.62 0.87 1.37 10-2470-605-01 1 0.81 1.59 3.18 2.25 4.87 1.71 0.87 1.37 10-2470-606-01 1-1/4 1.00 1.97 3.95 2.69 5.50 2.01 0.93 1.50 1/4-2070-607-01 1-1/2 1.25 2.21 4.40 2.87 5.50 2.38 0.94 1.50 1/4-2070-608-01 2 1.50 2.34 4.69 3.00 5.50 2.50 0.94 1.50 1/4-20

70-600-01 Threaded 3-Way Ball Valve Ideal for applications requiring flow diversion, this valve combines the features of two 2-way valves. Its large portsmake tank selection and fluid transfers simpler. Easy quarter-turn operation.

• 400 psig WOG rating• 100 percent air tested under water

Model Size Dimensions (In.)Number (In.) A B C D E F G H70-903-01 1/2 0.50 1.44 2.87 1.75 3.87 1.34 0.628 0.5070-904-01 3/4 0.68 1.94 3.87 2.12 4.87 1.69 0.878 0.9070-905-01 1 0.81 2.19 4.42 2.25 4.87 1.87 1.129 0.90

70-900-01 3-Way Diverter Valve With Solder EndsTank selection and fluid transfers are easier because of this diverter valve’s large ports. Rated 400 psig WOG. Thevalve is 100 percent air tested under water.

• Simple quarter-turn operation• Many long service life features

Diverter Valves

11

Ball Valves


Model Size Dimensions (In.)Number (In.) A B C D E F G H7B-101-01 1/4 0.37 1.03 2.06 1.37 2.68 0.93 0.53 1/8 NPT7B-102-01 3/8 0.37 1.03 2.06 1.37 2.68 0.93 0.53 1/8 NPT7B-103-01 1/2 0.50 1.09 2.18 1.43 2.68 1.00 0.53 1/8 NPT7B-104-01 3/4 0.75 1.28 2.68 1.62 3.00 1.12 0.75 1/8 NPT7B-105-01 1 1.00 1.66 3.43 1.90 4.00 1.31 0.94 1/8 NPT7B-106-01 1-1/4 1.25 1.87 3.87 2.18 4.00 1.62 1.15 1/4 NPT7B-107-01 1-1/2 1.50 2.05 4.22 2.60 5.62 1.81 1.31 1/4 NPT7B-108-01 2 2.00 2.47 5.02 2.95 5.62 2.18 1.68 1/4 NPT

7B-100-01 Full Port Hydro Valve With Double Female NPT Design features tee handle and side tapping; can be used as a drain feature or with 1/8" and 1/4" test cocks. Valveoffers extended service life with its chromium-plated ball and RPTFE seats and stuffing box ring.

• Rated 400 psig WOG, cold, non-shock • Blowout-proof stem design

Model Size Dimensions (In.)Number (In.) A B C D E F G H7B-301-01 1/4 0.37 2.13 2.92 1.37 2.68 0.93 0.53 1/8 NPT7B-303-01 1/2 0.50 2.21 3.08 1.43 2.68 0.93 0.53 1/8 NPT7B-304-01 3/4 0.75 2.25 3.67 1.62 3.00 1.12 0.75 1/8 NPT7B-305-01 1 1.00 2.71 4.50 1.90 4.00 1.31 0.94 1/8 NPT7B-307-01 1-1/2 1.50 3.43 5.62 2.60 5.62 1.81 1.31 1/4 NPT7B-308-01 2 2.00 4.00 6.56 2.95 5.62 2.18 1.68 1/4 NPT

7B-300-01 Full Port Hydro Valve With Two Female NPT Ports And Single Union End Valve offers union ends to make assembly and disassembly easier. Rated 400 psig WOG, cold, non-shock, it isequipped with a rugged chromium-plated ball and PTFE seats and stuffing box ring.

• Stem designed to be blowout-proof• Full flow, minimum pressure drop

Model Size Dimensions (In.)Number (In.) A B C D E F G H7B-801-01 1/4 0.37 1.40 2.43 1.37 2.56 0.93 0.53 1/8 NPT7B-802-01 3/8 0.37 1.46 2.50 1.37 2.56 0.93 0.53 1/8 NPT7B-803-01 1/2 0.50 1.68 2.78 1.43 2.56 1.00 0.53 1/8 NPT7B-804-01 3/4 0.75 1.88 3.28 1.70 2.68 1.12 0.75 1/8 NPT7B-805-01 1 1.00 2.39 4.17 1.93 3.62 1.31 0.94 1/8 NPT7B-806-01 1-1/4 1.25 2.66 4.66 2.13 3.62 1.62 1.15 1/4 NPT7B-807-01 1-1/2 1.50 2.86 5.03 2.71 5.12 1.81 1.31 1/4 NPT7B-808-01 2 2.00 3.34 5.89 3.06 5.12 2.18 1.68 1/4 NPT

7B-800-01 Male x Female Full Port Hydro Ball Valve Eliminates leak path and need for extra nipples. Full port design assures full flow and minimum pressure drop. Long-life features include adjustable packing gland, chromium-plated ball and RPTFE stuffing box ring.

• Rated 125 psig for saturated steam• 400 psig WOG, cold, non-shock

Two-Piece Full Port Valves

12

Ball Valves


77-100-01 Full Port NPT Ball Valve Designed for easy actuator mounting or panel mounting where highest Cv values are required. Chromium-plated balland RPTFE seats and stuffing box ring. Also available with solder connections and 250 lb. steam trim option.

• Full flow and minimum pressure drop • Extended stems optional

• Chain lever kits available 3⁄4" - 2 1⁄2"

Model Size Dimensions (In.)Number (In.) A B C D E F G77-101-01 1/4 0.43 1.12 2.25 1.81 3.87 0.50 1.1277-102-01 3/8 0.50 1.12 2.25 1.81 3.87 0.50 1.1277-103-01 1/2 0.50 1.12 2.25 1.81 3.87 0.50 1.1277-104-01 3/4 0.81 1.56 3.12 2.12 4.87 0.87 1.3777-105-01 1 1.00 1.81 3.62 2.62 5.50 0.93 1.5077-106-01 1-1/4 1.25 2.12 4.25 2.87 5.50 0.93 1.5077-107-01 1-1/2 1.50 2.37 4.75 3.34 8.00 2.08 3.0677-108-01 2 2.00 2.65 5.37 3.71 8.00 2.41 3.5277-109-01 2-1/2 2.50 3.25 6.50 4.12 8.00 2.75 3.37

77-900-01 Full-Port SAE Straight-Thread O-Ring Boss Ball ValvesApollo® full-port SAE straight thread ball valves with O-Ring boss connections are designed for extended leak-freeand energy saving performance in a broad range of applications, especially in manufacturing environments. Theirstraight thread sealing technology is in high demand in the automotive industries and in fluid power applications.Sizes 1/4" to 2". Rated 600 WOG cold non-shock, 150 psig steam.

• Drilled and tapped actuation pad standard• Chrome plated ball standard

• Blowout-proof stem and lever handle standard

Model Nom.Tube Dimensions (In.)Number O.D. (In.) Size (In.) A B C D E F G77-901-01 1/4 7/16-20 0.43 1.12 2.25 1.81 3.87 0.50 1.1277-902-01 3/8 9/16-18 0.50 1.12 2.25 1.81 3.87 0.50 1.1277-903-01 1/2 3/4-16 0.50 1.12 2.25 1.81 3.87 0.50 1.1277-904-01 3/4 11/16-12 0.81 1.56 3.12 2.12 4.87 0.87 1.3777-905-01 1 15/16-12 1.00 1.81 3.62 2.62 5.50 0.93 1.5077-906-01 1-1/4 1-5/8-12 1.25 2.12 4.25 2.87 5.50 0.93 1.5077-907-01 1-1/2 1-7/8-12 1.50 2.37 4.75 3.34 8.00 2.08 3.0677-908-01 2 2-1/2-12 2.00 2.65 5.37 3.71 8.00 2.41 3.52

13

Ball Valves


Model Size Dimensions (In.)Number (In.) A B C D E F G H71-104-01 3/4 0.68 1.50 3.00 2.12 4.87 0.87 1.37 10-24 NC71-105-01 1 0.87 1.68 3.37 2.25 4.87 0.87 1.37 10-24 NC71-106-01 1-1/4 1.00 2.00 4.00 2.62 5.50 0.93 1.50 1/4-20 NC71-107-01 1-1/2 1.25 2.18 4.37 2.87 8.00 0.93 1.50 1/4-20 NC71-108-01 2 1.50 2.34 4.68 3.06 8.00 0.93 1.50 1/4-20 NC71-100-01 3 2.50 3.37 6.75 4.12 8.00 N/A 2.75 1/4-20 NC

71-100-01 Ball Valve With Mounting PadValve designed to easily accommodate spring return handle, actuator or simple panel mounting. Threaded end con-nections with RPTFE seats and stuffing box ring. Standard port.

• 3⁄4" to 3" models • Round handle optional

Standard Two-Piece Valve w/Mounting Pad

3/4" - 2"Size

Model Size Dimensions (In.)Number (In.) A B C D E F G H71-144-64 3/4 0.68 1.50 3.00 2.12 4.87 0.87 1.37 10-24 NC71-145-64 1 0.87 1.68 3.37 2.25 4.87 0.87 1.37 10-24 NC71-146-64 1-1/4 1.00 2.00 4.00 2.62 5.50 0.93 1.50 1/4-20 NC71-147-64 1-1/2 1.25 2.18 4.37 2.87 8.00 0.93 1.50 1/4-20 NC71-148-64 2 1.50 2.34 4.68 3.06 8.00 0.93 1.50 1/4-20 NC71-140-64 3 2.50 3.37 6.75 4.12 8.00 N/A 2.75 1/4-20 NC

71-140-64 250 Lb. Steam Valve With Mounting PadDesigned for reliable operation on high pressure steam systems and with fluids of widely varying temperatures. Ideal for use with high thermal expansion rates. Stainless steel ball and stemstandard. Ball has a thermal relief hole drilled into stem slot.

• Multi-filled RPTFE seats • Special high-temperature MTFE stem packing

Steam Valves

3/4" - 2"Size

14

Ball Valves


Model Size Dimensions (In.)Number (In.) A B C70-103 1/2 0.50 1.12 2.2570-104 3/4 0.68 1.50 3.0070-105 1 0.87 1.68 3.3770-106 1-1/4 1.00 2.00 4.0070-107 1-1/2 1.25 2.18 4.3770-108 2 1.50 2.34 4.68

70-100-BC Ball Valve With Integral CheckUnidirectional ball valve ideally suited for all water and air systems not to exceed 250 psig. This combination productoffers a positive shut-off and a bubble-tight check capability where space savings is a must. Perfect for OEM use.

• Sizes 1⁄2" through 2"• FNPT Threads

Unidirectional Ball Valves

Model Size Dimensions (In.)Number (In.) A B C D E70-121-01 1/4 0.37 1.03 2.06 1.75 3.8770-122-01 3/8 0.37 1.03 2.06 1.75 3.8770-123-01 1/2 0.50 1.12 2.25 1.75 3.8770-124-01 3/4 0.68 1.50 3.00 2.12 4.8770-125-01 1 0.87 1.68 3.37 2.25 4.8770-126-01 1-1/4 1.00 2.00 4.00 2.62 5.5670-127-01 1-1/2 1.25 2.18 4.37 3.06 5.5670-128-01 2 1.50 2.34 4.68 3.25 5.5670-129-01 2-1/2 2.50 3.25 6.50 4.12 5.5670-120-01 3 2.50 3.37 6.75 4.12 5.56

70-120-01 Ball Valve With Adjustable Stop Lever This versatile hydronic valve provides easy screw controlled incremental balancing adjustments when variation isneeded. Special design makes a model combination shut-off and balancing valve.

70-120-04 Valve With Balancing Stop And Stem ExtensionIdeal for HVAC systems, valve offers a balancing stop plate and a 2-1/4" stem extension combination to accommo-date insulation and handle repositioning. Rated 600 psig WOG, cold, non-shock; 150 psig for saturated steam.

• Chromium-plated ball• RPTFE seats, stuffing box ring• Blowout-proof stem design and adjustable packing gland• Contact customer service for exact handle dimensions

Hydronic Valves

E

D

70-150-01 Ball Valve With Standard Balancing Stop PlateDesigned for hydronic applications, this valve comes with a simple stop plate that fits over its standard lever handle.Also available with tee or round handles. Features a chromium-plated ball, RPTFE seats and stuffing box ring, ablowout-proof stem design and adjustable packing gland.


15

Ball Valves


70-200-C8 Bronze Standard Port Ball Valve With 6” Female Brazed ExtensionsSolder end, 600 psig WOG, cold non-shock. 150 psig Saturated Steam. Vacuum Service to 29 inches Hg.MSS SP-110:Ball Valves, Threaded, SW, Solder Joint, Grooved & Flared Ends.

• Chromium plated ball• Adjustable packing gland• RPTFE seats and stuffing box ring• Blow-out proof stem design

Model Size Dimensions (In.)Number (In.) A B C D E F G H70-203-C8 1/2 0.50 1.43 2.87 1.75 3.87 0.63 0.50 14.8770-204-C8 3/4 0.68 1.93 3.87 2.12 4.87 0.88 0.75 15.8770-205-C8 1 0.87 2.25 4.50 2.25 4.87 1.13 0.90 16.5070-206-C8 1-1/4 1.00 2.31 4.62 2.62 5.50 1.38 0.96 16.6270-207-C8 1-1/2 1.25 2.62 5.25 3.06 8.00 1.63 1.09 17.2570-208-C8 2 1.50 3.18 6.37 3.25 8.00 2.13 1.34 18.3770-209-C8A 2-1/2 2.00 3.74 7.51 3.75 8.00 2.63 1.48 19.5170-200-C8 3 2.50 4.12 8.25 4.12 8.00 3.13 1.67 20.25

77-200-C8 Bronze Full Port Ball Valve With 6” Female Brazed ExtensionsSolder end, 600 psig WOG, Cold Non-shock. 150 psig Saturated Steam. Vacuum Service to 29 inchesHg. MSS SP-110:Ball Valves, Threaded, SW, Solder Joint, Grooved & Flared Ends.

• Chromium plated ball• Adjustable packing gland• RPTFE seats and stuffing box ring• Blow-out proof stem design• Full port for full flow and min. pressure drop

Model Size Dimensions (In.)Number (In.) A B C D E F G H77-204-C8 3/4 0.81 2.12 4.12 2.12 4.87 0.88 0.75 16.1277-205-C8 1 1.00 2.33 4.64 2.62 5.50 1.13 0.90 16.6477-206-C8 1-1/4 1.25 2.60 5.15 2.87 5.50 1.38 0.96 17.1577-207-C8 1-1/2 1.50 3.00 6.00 3.34 8.00 1.63 1.09 18.0077-208-C8 2 2.00 3.62 7.24 3.71 8.00 2.13 1.34 19.2477-209-C8 2-1/2 2.50 3.93 7.87 4.12 8.00 2.63 1.48 19.87

16

Ball Valves


70-200-63 Ball Valve With Threaded And Solder Ends Eliminates special pipe connector for connecting dissimilar piping such as iron and copper. Reliable shut-off andeasy quarter-turn operation. Features chromium-plated ball, a blowout-proof stem design and RPTFE seats and stuffing box ring.

• 150 psig for saturated steam• Rated 600 psig WOG, cold, non-shock

78-100-01 Cap And Chain Valve With Threaded x 3/4 Inch Hose Connection Ideally suited for direct connections to hoses, valve features a securely attached cover with chain which preventsdamage to hose threads. -200 model designed for soft soldering into lines without disassembly. Features chromium-plated ball, blowout-proof stem design and RPTFE seats and stuffing box ring.

• Adjustable packing gland • New pressure-containing version available

Model Size Dimensions (In.)Number (In.) A B C D E F78-103-01 1/2 NPT x 3/4 Hose 0.50 1.68 2.81 2.95 3.87 1.7578-104-01 3/4 NPT x 3/4 Hose 0.68 1.96 3.50 3.65 4.87 2.1278-203-01 1/2 Solder x 3/4 Hose 0.50 1.65 3.07 3.22 3.87 1.7578-204-01 3/4 Solder x 3/4 Hose 0.68 1.93 3.85 4.00 4.87 2.12

78-664-01 Bronze Ball Valve With Center DrainCenter tap drain allows for winterization or purge and drain function. Features bronze body with built-in mounting padfor panel mounting or actuation. Chrome plated ball, RPTFE seats and stuffing box ring are standard, as are stain-less steel lever and nut. Ideal for hydronic heating and marine applications.

• Sizes 3⁄4" through 2"• Tapered Pipe Threads

Model Size Dimensions (In.)Number (In.) A B C D E F G H78-664-01 3/4 0.68 1.50 3.00 2.12 4.87 0.87 1.37 0.1778-665-01 1 0.87 1.68 3.37 2.25 4.87 0.87 1.37 0.2178-666-01 1-1/4 1.00 2.00 4.00 2.62 5.50 0.93 1.50 0.2878-667-01 1-1/2 1.25 2.18 4.37 3.05 8.00 0.93 1.50 0.4078-962-01 2 1.50 2.34 4.68 3.24 8.00 0.93 1.50 0.45

10-24 NC ALL SIZES

17

Ball Valves


95-200-01 Full Port Solder End Stop And Waste Valve Perfect choice for hydronic and water systems where system draining is required. Replaces globe style stop andwaste valves. Designed to be soft soldered into lines with no disassembly.

• Rated 400 psig WOG, cold non-shock• Drain cap designed to prevent fluid loss • Adjustable packing gland

Model Size Dimensions (In.)Number (In.) A B C D E F G95-203-01 1/2 0.50 1.43 2.87 1.75 3.87 0.63 0.5095-204-01 3/4 0.81 2.12 4.12 2.15 4.87 0.88 0.7595-205-01 1 1.00 2.21 4.43 2.43 4.87 1.13 0.90

18

Ball Valves


78-250/260 Instrumentation Valves

78-250: Bronze

78-260: Brass

78-620-01 Threaded Irrigation Valve Ideal for underground use or where drained media will not cause damage. Auto-drain feature is standard. Features astainless steel cover, chromium-plated ball, adjustable packing gland, RPTFE seats and seals and blowout-proofstem design.

• Rated 200 psig water, cold, non-shock• Temperature range: +50°F to 200°F

Irrigation Valves

Model Size Dimensions (In.)Number (In.) A B C D E78-621-01 3/4 0.68 1.47 2.96 2.40 1.8178-622-01 1 0.87 1.66 3.34 2.53 1.8178-623-01 1-1/4 1.00 1.98 3.97 3.00 2.5078-624-01 1-1/2 1.25 2.12 4.28 3.18 2.5078-625-01 2 1.50 2.35 4.67 3.37 2.50

Brass And Bronze Instrumentation Ball ValveMale x Female Threaded. 400 psig WOG, Cold Non Shock. Air & Liquid Service Rating.

BRASS INSTRUMENTATION BALL VALVE- Tee HandleModel Size Dimensions (In.)Number (In.) A B C D E Cv* Wt.78-260-05 1/8M X 1/8F 0.21 0.37 1.43 0.87 1.25 4.00 0.2078-261-05 1/4M X 1/4F 0.31 0.43 1.43 0.87 1.25 5.50 0.19

BRASS INSTRUMENTATION BALL VALVE - Screw SlotModel Size Dimensions (In.)Number (In.) A B C D E Cv* Wt.78-262-05 1/8M X 1/8F 0.21 0.37 1.43 0.75 N/A 4.00 0.2078-263-05 1/4M X 1/4F 0.31 0.43 1.43 0.75 N/A 5.50 0.19

BRONZE INSTRUMENTATION BALL VALVE - Screw SlotModel Size Dimensions (In.)Number (In.) A B C D E Cv* Wt.78-257-01 1/8M X 1/4F 0.21 0.80 1.60 0.72 N/A 4.00 0.1978-258-01 1/4M X 1/4F 0.31 0.80 1.60 0.72 N/A 5.50 0.19

BRONZE INSTRUMENTATION BALL VALVE - Lever HandleModel Size Dimensions (In.)Number (In.) A B C D E Cv* Wt.78-267-01 1/4M X 1/4F 0.25 0.65 1.45 0.93 1.37 5.50 0.20

*The Cv factor is the gallons of water per minute that the valve will pass with a 1 psigpressure drop.

• Micro-finish ball• Blow-out-proof stem design• PTFE seats• Nitrile stem seal

• Plated steel tee handle• Compact design• Optional mixed end fittings avail-

able

19

Ball Valves


78-114-01 Optional End Connection Valve for Underground Service The 78-114-01 features the same square head nut as the 78-130 Series but with an optional SAE male thread onone end. Apollo® valves can be manufactured with a variety of end connections to meet your specific undergroundservice requirements.

78-130 Female End Valve for Underground Service The 78-130 Series is ideal for underground or below grade applications. This series (1/4" - 2" FNPT) features asquare head nut welded to the stem to allow operations with a ground key from standard grade.

Refrigerant Valves

79-700-01 UL-Listed Refrigerant Ball Valve AssemblyBuilt for easy installation and long service life. Complete hermetically welded assembly includes copper extensionsand forged brass refrigerant ball valve with capped, triple-sealed stem to reduce leaks. Sizes from 3/8" to 3-1/8" O.D.Tube. Chrome plated ball; RPTFE seats and seals.

• Full-port through 2-5⁄8"• Bi-directional flow design• All sizes UL listed Model Size Dimensions (In.)

Number (In.) A B C D E F Cv*79-701-01 3/8 3.38 6.45 0.45 1.56 0.38 0.38 8.579-702-01 1/2 3.38 6.45 0.45 1.56 0.38 0.50 8.579-703-01 5/8 3.56 6.82 0.50 1.56 0.50 0.62 9.879-704-01 7/8 3.91 7.53 0.68 1.79 0.75 0.87 32.079-705-01 1-1/8 4.39 8.51 0.87 1.98 0.90 1.12 44.079-706-01 1-3/8 4.42 8.94 1.25 2.62 0.96 1.38 66.079-707-01 1-5/8 4.55 9.19 1.25 2.62 1.09 1.62 148.079-708-01 2-1/8 5.16 10.31 1.50 2.93 1.34 2.12 218.079-709-01 2-5/8 6.50 13.00 2.50 3.90 1.48 2.62 440.079-600-01 3-1/8 7.00 14.00 2.50 3.90 1.67 3.12 390.0

*The Cv factor is the gallons of water per minute that the valve will pass with 1 psig pres-sure drop.

20

Ball Valves


Air Exhaust Valves

7K-100-01 Full-Port Safety Exhaust Valve With 1/4" NPT Tap For DrainBuilt for easy installation and long service life. For use on pneumatic equipment where full flow is required.Standardly furnished with a 1/4" NPT tapped drain to accommodate a muffler or to pipe the exhausted air to a safelocation. For optional stainless steel latch lock handle that locks in the closed position only, specify suffix (-46).

• Sizes 1⁄4 " through 2-1⁄2"• FNPT Threads• Rated 125 psig – air or water• Temperature range: +50°F to +200°F

Gas/Fuel Shut-Off Valves

71-500-01 Valve With Spring Return HandleIdeal in applications where the valve must be in OFF position at all times such as feeding fuel lines. Can be used inreverse with 90° reverse stem option. Basic configuration: spring return to CLOSED. All lever components are stain-less steel.

• Spring return to OPEN optional • Torque nearly three times that of standard valves

Model Size Dimensions (In.)Number (In.) A B C D E F G H I J K7K-101-01 1/4 0.37 1.03 2.06 1.75 3.87 N/A N/A 0.09 0.53 1.18 N/A7K-102-01 3/8 0.37 1.03 2.06 1.75 3.87 N/A N/A 0.09 0.53 1.18 N/A7K-103-01 1/2 0.50 1.10 2.19 1.75 3.87 N/A N/A 0.12 0.59 1.25 N/A7K-104-01 3/4 0.81 1.56 3.12 2.12 4.78 0.87 1.37 0.29 0.90 1.56 0.907K-105-01 1 1.00 1.80 3.61 2.62 5.50 0.93 1.50 0.31 1.12 1.78 1.127K-106-01 1-1/4 1.25 2.12 4.25 2.87 5.50 0.93 1.50 0.37 1.37 2.03 1.377K-107-01 1-1/2 1.50 2.37 4.74 3.30 7.78 2.08 3.06 0.50 1.56 2.21 1.287K-108-01 2 2.00 2.70 5.38 3.71 7.78 2.41 3.52 0.62 2.03 2.68 1.567K-109-01 2-1/2 2.50 3.25 6.50 4.05 7.78 2.75 3.37 1.09 2.34 3.00 2.00

Model Size Dimensions (In.)Number Size (In.) A B C D71-501-01 1/4 0.43 1.12 2.25 7.0071-502-01 3/8 0.50 1.12 2.25 7.0071-503-01 1/2 0.50 1.12 2.25 7.0071-504-01 3/4 0.68 1.50 3.00 7.0071-505-01 1 0.87 1.68 3.37 7.0071-506-01 1-1/4 1.00 2.00 4.00 9.0071-507-01 1-1/2 1.25 2.18 4.37 9.0071-508-01 2 1.50 2.34 4.68 9.00

21

Ball Valves


78-256-01 Fuel Shut-Off Valve With Mounting EarsExcellent for use with liquid fuels and often specified as a fuel tank shut-off valve in marine applications. All wettedparts are brass or cast bronze. Features include mounting ears for easy, positive installation; 400 psig service ratingtested to 100 psig air under water. Optional tee handle saves space and still provides fast 90˚ on/off.

• NPT threaded, both ends• RPTFE seats and seals

Model Size Dimensions (In.)Number (In.)* A B C D E F G78-248-01 1/4 0.43 1.12 2.25 1.78 3.87 0.93 1.8778-250-01 3/8 0.43 1.12 2.25 1.78 3.87 0.93 1.8778-256-01 1/2 0.50 1.12 2.25 1.78 3.87 0.93 1.8778-438-01 3/4 0.68 1.50 3.00 2.12 4.87 1.06 2.12

Gas Cock Ball ValvesGB-10 Series CSA Gas Shutoff Valves

Manual shut-off valves engineered specifically for low-pressure gas service. Canadian Standard Association Designand capacity certified with American-made quality. High-copper content body, chrome-plated ball, PTFE seats. Ratedfor temperatures from 32˚F to 125˚F at pressures of 1/2 and 5 PSIG.

• Complies with CSA 3.88, ANSI Z21.15 and CR91-002

• Lever or tee handle options available• Use with natural, manufactured, mixed and lique-

fied petroleum gases, LP gas-air mixtures • Standard die-cast zinc “wing” handle, epoxy coat-

ed, for easy shut off

Model Size Number (In.) Connection BTU/Hr*51GB201 3/8 3/8 NPT 318,70051GB301 1/2 1/2 NPT 623,75051GB401 3/4 3/4 NPT 1,265,00051GB501 1 1 NPT 2,037,500

Dimensions (In.)Size (In.) A B C D E F G

3/8 2.04 1.06 0.38 3.85 2.24 2.20 0.811/2 2.24 1.18 0.50 3.85 2.30 2.24 0.813/4 2.97 1.55 0.69 4.75 2.85 2.90 1.001 3.33 1.81 0.88 4.75 3.10 3.15 1.00

* Capacity based on a gas having a heating value of 1000 Btu/cubic feet and an S.G. of 0.64 at a P.D. of 1” W.C.

G

F

A

B

Standard, yellow die-cast Zinc “wing handle.”

D

E

CB

A

Optional – StainlessSteel “lever handle”

22

Ball Valves


GB-12, GB-13,GB-14, GB-15,GB-16 Series

Gas Appliance Ball ValvesThese gas appliance ball valves are designed for natural gas, manufactured and mixed gas, liquefied petroleumgases and LP gas-air mixture applications. They comply with the latest editions of these published standards:

• ANSI Z21.15,CGA9.1• CSA No. 3-88• UL Guide YRBX

• UL Guide MHKZ• UL Guide YRPV• UL Guide YSDT

GB-14

Model Number Part Number Size & End Connection (In.)GB-12 51GC2T1 3/8 FNPT x FNPTGB-12 51GC3T1 1/2 FNPT x FNPTGB-12 51GC4T1 3/4 FNPT x FNPTGB-12 51GC5T1 1 FNPT x FNPTGB-13 51GD2T1 1/2 x 3/8 FNPT x FlareGB-13 51GD3T1 1/2 x 1/2 FNPT x FlareGB-13 51GD4T1 3/4 x 5/8 FNPT x FlareGB-14 51GE2T1 3/8 x 3/8 Flare x FlareGB-14 51GE3T1 1/2 x 1/2 Flare x FlareUNIBODY SERIESGB-15 51GF201 3/8 FNPT x 3/8 FNPTGB-15 51GF301 1/2 FNPT x 1/2 FNPTGB-15 51GF401 3/4 FNPT x 3/4 FNPTGB-16 51GG201 1/2 FNPT x 3/8 FlareGB-16 51GG301 1/2 FNPT x 1/2 Flare

GB-12

GB-13

GB-15 GB-16

23

Ball Valves


Dimensions (In.)Size (In.) End Connection L L2 H D d GB-123/8 FNPT x FNPT 1.81 1.77 1.29 0.39 n/a 1/2 FNPT x FNPT 2.16 1.77 1.29 0.39 n/a 3/4 FNPT x FNPT 2.44 1.77 1.41 0.59 n/a 1 FNPT x FNPT 2.87 2.75 1.57 0.78 n/aGB-131/2 x 3/8 FNPT x Flare 2.44 1.77 1.29 0.39 0.271/2 x 1/2 FNPT x Flare 2.51 1.77 1.29 0.39 0.393/4 x 5/8 FNPT x Flare 3.03 1.77 1.41 0.59 0.50GB-143/8 Flare x Flare 2.51 1.77 1.29 0.39 0.271/2 Flare x Flare 2.63 1.77 1.29 0.39 0.39UNIBODYSize End Connection L H D WGB-153/8 FNPT x FNPT 1.95 1.35 0.31 1.421/2 FNPT x FNPT 2.28 1.40 0.39 1.423/4 FNPT x FNPT 2.58 1.51 0.50 1.42GB-161/2 x 3/8 FNPT x Flare 2.48 1.40 0.39 1.421/2 x 1/2 FNPT x Flare 2.48 1.40 0.39 1.42

GB-12

GB-13

GB-14

Ø D

L

L

L

ød

ød

Ø D

Ø D

H

H

H

GB-15

GB-16

24

Ball Valves


G

I

G

H E

BC

F

GB-50

GB-50A

Number Dimensions(In.)Single Dual Size CapacityTapped Tapped (In.) Tapping A B C D E F G H I BTU/Hr.50GB301 -- 1/2 1/8 0.50 1.11 2.25 1.68 3.85 2.27 1.00 0.53 - 69300050GB401 50GB401A 3/4 1/8 0.75 1.26 2.67 1.93 3.85 2.72 1.12 0.75 2.24 125800050GB501 50GB501A 1 1/8 1.00 1.65 3.42 2.19 4.78 3.18 1.53 0.94 3.06 314400050GB601 50GB601A 1-1/4 1/8 1.25 1.87 3.86 2.37 4.78 3.56 1.62 1.15 3.24 644100050GB701 50GB701A 1-1/2 1/8 1.50 2.05 4.22 2.81 5.40 4.21 1.81 1.31 3.62 774500050GB801 50GB801A 2 1/8 2.00 2.48 5.02 3.18 5.40 4.93 2.18 1.68 4.36 1474100050GB5A1 50GB5A1A 1 1/4 1.00 1.65 3.42 2.19 4.78 3.18 1.53 0.94 3.06 314400050GB6A1 50GB6A1A 1-1/4 1/4 1.25 1.87 3.86 2.37 4.78 3.56 1.62 1.15 3.24 644100050GB7A1 50GB7A1A 1-1/2 1/4 1.50 2.05 4.22 2.81 5.40 4.21 1.81 1.31 3.62 774500050GB8A1 50GB8A1A 2 1/4 2.00 2.48 5.02 3.18 5.40 4.93 2.18 1.68 4.36 14741000

GB-50 & GB-50A Series

CSA Gas Shutoff Ball ValvesDesigned for indoor “main burner” applications, with cast-in single or dual pilot tap for faster, simpler installation.Fully complies with CSA 3-88, ANSI Z21.15, CGA9.1, single or dual and CR91-002 standards. ASTM B584bronze body, chrome-plated ball, brass stem, retainer and gland screws for corrosion resistance.

• For natural gas, manufactured and mixed gas, liq-uefied petroleum gases and LP gas-air mixtures

• Rated pressures of 1/2 and 5 psig• High capacity

• Comes standard with a reversible plated steellever handle. Options include a die-cast zinc “wing”handle and “tee” handle

• Standard connection is FNPT x FNPT

*Note: Capacities based on 1000 Btu/cubic feet gas at 0.64 specific gravity, at a P.D. of 1'' W.C.

UL CertificationsANSI Z21.15, CGA9.1 CSA 3.88 CR91-002

UL Guide YSDTUL Guide YRPVUL GuideYRBXUL Guide MKHZ

D

25

Ball Valves


80-100-01 UL-Listed Gas Shut-Off ValveUL-listed and designed as safe shut-off valve for LP gas, natural gas, flammable liquids and heated oil. Optionalunplated ball model meets code requirements. Features easy quarter-turn ON/OFF, a large port to reduce pressuredrop and NPT connections.

• RPTFE seats and seals

Model Size Dimensions (In.)Number (In.) A B C D E80-101-01 1/4 0.37 1.03 2.06 1.75 3.8780-102-01 3/8 0.37 1.03 2.06 1.75 3.8780-103-01 1/2 0.50 1.12 2.25 1.81 3.8780-104-01 3/4 0.68 1.50 3.00 2.12 4.8780-105-01 1 0.87 1.68 3.37 2.25 4.8780-106-01 1-1/4 1.00 2.00 4.00 2.62 5.5080-107-01 1-1/2 1.25 2.18 4.37 2.87 5.5080-108-01 2 1.50 2.34 4.68 3.06 5.5080-109-01 2-1/2 2.50 3.25 6.50 4.12 8.0080-100-01 3 2.50 3.37 6.75 4.12 8.00

90-100-01 UL-Listed Uni-Body Threaded Ball ValveA compact valve that’s UL listed at 300 psig for fuel, inert gases and flammable liquids. Features chromium-platedball, RPTFE seats and seals.

• Blowout-proof stem design • One-piece bronze body • Optional tee handle

Model Size Dimensions (In.)Number (In.) A B C D E90-103-01 1/2 0.37 1.14 2.15 1.68 3.8790-104-01 3/4 0.50 1.36 2.61 1.75 3.8790-105-01 1 0.62 1.50 2.90 2.00 4.8790-106-01 1-1/4 0.81 1.81 3.50 2.18 4.8790-107-01 1-1/2 1.00 2.06 3.79 2.62 5.5090-108-01 2 1.25 2.43 4.42 2.81 5.50

26

Ball Valves


82-100-01 Full-Port 3-Piece ValveThis in-line repairable threaded ball valve offers RPTFE seats and seals and a 600 WOG rating. SAE Grade 8body bolts standard.

• Rated 150 psig saturated steam • Static grounding devices optional

Model Size Dimensions (In.)Number (In.) A B C D E82-101-01 1/4 0.43 1.28 2.56 1.81 3.8782-102-01 3/8 0.50 1.28 2.56 1.81 3.8782-103-01 1/2 0.62 1.40 2.81 1.93 4.8782-104-01 3/4 0.81 1.71 3.43 2.18 4.8782-105-01 1 1.00 1.93 3.87 2.62 5.5082-106-01 1-1/4 1.25 2.37 4.75 2.87 5.5082-107-01 1-1/2 1.50 2.62 5.25 3.37 8.0082-108-01 2 2.00 3.01 6.03 3.68 8.0082-109-01 2-1/2 2.50 3.62 7.25 5.14 9.7582-140-01 3 3.00 4.00 8.00 6.77 18.0082-14A-01 4 4.00 5.50 11.00 8.26 18.00

3-Piece Full-Port Valves

75-100-41 Padlocking Ball Valve With Automatic DrainMeets OSHA standards and provides for easy, safe maintenance of pneumatic tools. Valve can be padlocked OPENor CLOSED with same hardware. Built with RPTFE seats and stuffing box ring, a blowout-proof stem design,adjustable packing gland and chromium-plated ball. (Also available without drain option. Specify suffix -01).

• Threaded end connections • Rated to 200 psig – air or water• Temperature range: +50°F to 200°F


Padlocking Valves

27

Ball Valves


82-100-19 Full-Port 3-Piece Valve With Locking Plate Threaded valve features a 3-piece design that makes in-line repairs easy. Meets OSHA lock-out standards. It’sequipped with RPTFE seats. Two bolts are steel, two are stainless steel. (Option -19 not available on 2-1/2" size).

• Rated 150 psig for saturated steam• 600 psig WOG cold, non-shock

82-100-63 Full-Port 3-Piece Valve With NPT x Solder EndsBuilt to make in-line repairs fast and simple, this valve features RPTFE seats and seals and a 600 WOG rating.It’s equipped with SAE Grade 8 body bolts.

• Full port flow advantages• Adjustable packing gland

82-140-57 Full-Port 3-Piece Valve With 316 Stainless Steel Ball/StemCleaned for gaseous oxygen, valve is equipped with NPT connections and features RPTFE seats and seals,blowout-proof stem design and adjustable packing gland.

• Rated 600 psig cold, non-shock• 150 psig for saturated steam

28

Ball Valves


82-200/82-240 3-Piece Full-Port Valve With Brazed TubingAlso available: with nominal 6” type K tubing brazed into the solder end cup – cleaned for oxygen service (optionsuffix -57). This valve is useful in pharmaceutical, medical gas and pneumatic applications where valves shouldnot be disassembled prior to soldering or brazing.

82-200-01 Full-Port 3-Piece Solder End ValveValve features full-port and is easily repaired in-line. Designed for soft soldering or brazed installation. IncludesRPTFE seats and seals.

• Chromium-plated ball • Equipped with SAE Grade 8 body bolts

Standard Oxygen CleanedModel Model Numbers Model Model Numbers Dimensions (In.)Numbers 316 Ball & Stem Numbers 316 Ball & Stem Size (In.) A*(In.) B C D E F G82-203-B8 82-243-A8 82-203-A1 82-243-A7 1/2 5/8 0.62 0.05 13.81 2.00 4.87 6.0082-204-A8 82-244-B3 82-204-A2 82-244-B2 3/4 0.87 0.81 0.07 13.93 2.18 4.87 6.0082-205-B7 82-245-B1 82-205-A1 82-245-B0 1 1.12 1.00 0.07 14.04 2.62 5.50 6.0082-206-B7 82-246-B0 82-206-A1 82-246-A9 1-1/4 1.37 1.25 0.07 14.81 2.87 5.50 6.0082-207-B2 82-247-B2 82-207-A1 82-247-B0 1-1/2 1.62 1.50 0.07 15.07 3.37 8.00 6.0082-208-B7 82-248-B2 82-208-A1 82-248-B1 2 2.12 2.00 0.08 15.23 3.70 8.00 6.00

*

Nominal Tubing O.D.

Model Size* Dimensions (In.)Number (In.) A B C D E F G82-202-01 3/8 0.50 1.28 2.56 1.81 3.87 0.50 0.3782-203-01 1/2 0.62 1.40 2.81 1.93 4.87 0.63 0.5082-204-01 3/4 0.81 1.71 3.43 2.18 4.87 0.88 0.7582-205-01 1 1.00 1.93 3.87 2.62 5.50 1.13 0.9082-206-01 1-1/4 1.25 2.37 4.75 2.87 5.50 1.38 0.9682-207-01 1-1/2 1.50 2.60 5.25 3.37 8.00 1.63 1.0982-208-01 2 2.00 3.01 6.03 3.68 8.00 2.13 1.3482-209-01 2-1/2 2.50 3.62 7.25 5.14 9.38 2.63 1.4782-240-01 3 3.00 4.00 8.00 6.77 18.00 3.13 1.6682-24A-01 4 4.00 5.50 11.00 8.26 18.00 4.13 2.16

29

Ball Valves


9A-100-01 Heavy Pattern Uni-Body Threaded Ball ValveOne-piece bronze valve eliminates leak paths. Features static grounding devices and adjustable packing gland.Lever handle standard.

• Rated 600 psig WOG• Blowout-proof stem design

General Purpose Uni-body Valves

Dual Wye Auto Drain Ball Valve Dual action modular valve, ideal for compressor applications where safety exhaust may be needed for two airlines at once.

3-Way, 4-Seated Ball Valve with Flanged Pump ConnectionsThis special valve can be used in hydronic geothermal or other HVAC applications where diversion of flow isrequired, along with positive shut off. Designed to connect directly to circulator pump flange connections.

Specialty Valves

Model Size Dimensions (In.)Number (In.) A B C D E9A-101-01 1/4 0.37 1.34 2.59 1.68 3.879A-102-01 3/8 0.37 1.34 2.59 1.68 3.879A-103-01 1/2 0.37 1.34 2.59 1.81 3.879A-104-01 3/4 0.50 1.44 2.84 1.84 3.879A-105-01 1 0.62 1.72 3.28 2.00 4.879A-106-01 1-1/4 0.81 1.94 3.84 2.18 4.879A-107-01 1-1/2 1.00 2.06 4.00 2.68 5.509A-108-01 2 1.25 2.29 4.56 2.87 5.50

91-100-01 Threaded Uni-Body Ball Valve A compact valve featuring a chromium-plated ball, adjustable packing gland, blowout-proof stem design andRPTFE seats and seals. Lever handle standard, tee handle optional.

• 400 psig WOG cold non-shock • 150 psig saturated steam


30

Ball Valves


IBVE-125 Series

• For additional technical information, request #PHBRIRBV brochure

Apollo International Epoxy Coated Cast Iron Full Port Class 125 Flanged Ball ValveBVE-125 Series valves have all the design and construction features of the IBV-125 plus an FDA-approved,heat-fused epoxy coating making them ideal for corrosive water service as well as food contact applications.Maximum operating temperature: 140˚F.

IBVD-125 Series Apollo International Ductile Iron Full Port Class 125 Flanged Ball ValveIBVD-125 series valves have the same design and construction features of the IBV-125 series but in ductileiron. Same dimensional data as IBV/IBVE series. Available in sizes 2" through 6".

Dimensions (In.)IBV IBVE IBVD Size Wt./100Model Number Model Number Model Number (In.) A B C D (Lbs.)6P-208-01 6Q-208-01 6R-208-01 2 7.00 6.00 9.00 3.00 22.06P-209-01 6Q-209-01 6R-209-01 2-1/2 7.50 7.00 16.00 3.70 34.06P-200-01 6Q-200-01 6R-200-01 3 8.00 7.50 16.00 4.00 38.06P-20A-01 6Q-20A-01 6R-20A-01 4 9.00 9.00 19.70 4.80 58.06P-20C-01 6Q-20C-01 6R-20C-01 6 10.50 11.00 26.00 7.20 118.06P-20E-01 6Q-20E-01 - 8* 11.50 13.50 - 9.24 345.06P-20G-01 - - 10* 13.00 16.00 - 11.81 440.0

C

D

A

B

* with manual gear operator

IBV-125 Series

• Gear operator standard 8" and 10"• Full-port design offers superior flow rate• No bronze seat rings, disc rings or stems

to wear out • Quarter-turn offers instant, positive shutoff with

zero leakage• Stainless steel ball resists corrosion• Handle indicates valve operation status

• Large actuator mounting pad standard• Optional locking handles available• Blowout-proof stainless steel stem • PTFE seats and packing, not Nitrile or EPDM• Opens and closes easily, without cheater bar• For more technical information, request

#PHBRIRBV brochure

Apollo® International Cast Iron Full-Port Class 125 Flanged Ball ValvesThe Conbraco IBV-125 Series cast iron ball valve meets MSS SP-72, ANSI B16.10 and federal WW-V-35 per-formance standards. They can be used to replace any IBBM gate valve or plug valve. With their full port design,these valves assure an unobstructed, turbulence-free flow that gate and butterfly valves can’t match. Low pro-file handle for easy installation in tight areas. Sizes from 2" to 10". Rated 125 WSP, 200 WOG, with a maxi-mum operating temperature of 350˚F.

Valves For Water Service

31

Ball Valves


94 MBV Mini Ball ValveThe Mini Ball Valve is designed for steam, water, oil or gas in commercial and light industrial use. The mini-valves are a competitive, conventional port, constructed of heavy-duty forged brass, 100% Teflon® seatsand gland follower with double viton o-rings, to prevent stem leakage. The valves are equipped with areversible handle for tight space applications. The valve connections are manufactured in accordance withANSI B1.20.1. The valves are pressure rated to a maximum of 600 psig at 100°F. Rated service tempera-ture ranges are from -40°F to 300°F.

• Reversible Handle• Rugged Forged Construction• Greater Flow Rate• Blow Out Proof Stem• Double Viton O-rings• Large Raised Wrench Flats• Chrome Plated Brass Ball• Each Mini is Air-Tested Twice: In the Open and Closed Position• Use as a Non-leak Gauge Cock/Test Cock• Perfect for O.E.M. Applications

Model Size Dimensions (In.) InternalNumber (In.) A B C Ø Wt. (Lbs.)94MBV01 1/4 FNPT x 1/8 MNPT 1.96 1.25 1.67 0.31 0.1994MBV02 1/4 FNPT x 1/4 MNPT 2.04 1.15 1.67 0.31 0.2094MBV03 1/4 FNPT x 1/4 FNPT 1.63 1.28 1.67 0.31 0.1794MBV04 1/8 FNPT x 1/8 MNPT 1.97 1.20 1.67 0.31 0.1694MBV05 1/8 FNPT x 1/8 FNPT 1.61 1.23 1.67 0.31 0.16

32

Ball Valves


64-100 Dimensions (In.)Model Number Size (In.) A B C D Cv64-101-01 1/4 NPT 0.39 2.02 1.75 3.85 664-102-01 3/8 NPT 0.39 2.02 1.75 3.85 764-103-01 1/2 NPT 0.59 2.44 1.88 3.85 1964-104-01 3/4 NPT 0.78 2.71 2.28 4.80 3464-105-01 1 NPT 0.98 3.07 2.44 4.80 5064-106-01 1-1/4 NPT 1.25 3.42 3.07 6.02 10464-107-01 1-1/2 NPT 1.57 3.89 3.34 6.02 26864-108-01 2 NPT 1.96 4.33 3.79 6.37 30964-109-01 2-1/2 NPT 2.56 5.59 5.02 8.07 62964-100-01 3 NPT 3.15 6.45 5.45 8.07 101864-10A-01 4 NPT 3.94 7.60 6.34 10.23 1622

64-200 Dimensions (In.)Model Number Size (In.) A B C D Cv"64-203-01 1/2 0.59 2.53 1.88 3.85 1964-204-01 3/4 0.78 2.99 2.28 4.80 3464-205-01 1 0.98 3.58 2.44 4.80 5064-206-01 1-1/4 1.25 4.09 3.07 6.02 10464-207-01 1-1/2 1.57 4.56 3.34 6.02 26864-208-01 2 1.96 5.43 3.79 6.37 30964-209-01 2-1/2 2.56 6.93 5.02 8.07 62964-200-01 3 3.15 8.09 5.45 8.07 101864-20A-01 4 4.13 10.25 6.34 10.23 1622

64 Series

• Sizes from 1/4" to 4"• Threaded (-100) and solder end (-200)

connections• Pressure rated to 600 psig WOG; 150 psig

steam

• Temperatures to 366˚F (185˚C)• Blowout-proof stem • Chrome-plated brass ball • Secondary O-ring stem seal• PTFE seats, thrust bearing and stem packing

Apollo® International Full Port Brass Ball ValvesEconomy full-port forged ball valve with maximum flow; ideal choice for all plumbing applications. Lever handleis standard on all sizes.

Optional Kits Stem Balancing Locking LeverValve Size (In.) Extensions Stops Handles Handles1/4, 3/8 and 1/2 78-1501-01 78-1506-01 78-1659-01 78-1646-01*3/4 and 1 78-1502-01 78-1507-01 78-1660-01 78-1647-011-1/4 and 1-1/2 78-1503-01 78-1508-01 78-1661-01 78-1648-012 78-1504-01 78-1509-01 78-1662-01 78-1649-012-1/2 and 3 78-1505-01 78-1510-01 - 78-1650-014 - - - 78-1651-01

Note: Specify -07 suffix for “T” handle, ie. 64-105-07. Available with threaded models only in 1/4”-1” sizes.* Lever handle available on 1/2" - 4".

95A Series Apollo International Full Port Brass Ball Valve With Stop & Waste

Threaded Sweat Size (In.)95A-303-01 95A-403-01 1/295A-304-01 95A-404-01 3/495A-305-01 95A-405-01 1

Economy Valves

SECTION A CONTENTSTWO PIECE BALL VALVES

DESCRIPTION PAGE

70-100 Series, Threaded Bronze A-1

70-200 Series, Solder Bronze A-2

70-800 Series, M x F Threaded Bronze A-3

71-100 Series, Threaded Bronze with Mounting Pad A-4

71-AR Series, Actuator Ready Threaded Bronze (New Item) A-5

72-100 Series, Threaded High Pressure Carbon Steel A-6

72-900 Series, SAE Straight Thread Carbon Steel A-7

73-100 Series, Threaded Carbon Steel A-8

73A-100 Series, Threaded Forged Carbon Steel (New Item) A-9

76-100 Series, Threaded Stainless Steel with Mounting Pad A-10

76-AR Series, Actuator Ready Threaded Stainless Steel (New Item) A-11

77-100 Series, Threaded Full Port Bronze with Mounting Pad A-12

77-AR Series, Actuator Ready Threaded Full Port Bronze (New Item) A-13

77-200 Series, Solder Bronze, Full Port A-14

77-900 Series, SAE Straight Thread Bronze A-15

89-100 Series, Threaded Carbon Steel with Mounting Pad A-16

89-AR Series, Actuator Ready Threaded Carbon Steel (New Item) A-17

399-100 Series, Threaded Alloy-20 with Mounting Pad A-18

NUMBER SIZE A B C D E Wt.70-101-01 1/4" .37 1.03 2.06 1.75 3.87 .6070-102-01 3/8" .37 1.03 2.06 1.75 3.87 .5670-103-01 1/2" .50 1.12 2.25 1.75 3.87 .6370-104-01 3/4" .68 1.50 3.00 2.12 4.87 1.3970-105-01 1" .87 1.68 3.37 2.25 4.87 1.7270-106-01 1-1/4" 1.00 2.00 4.00 2.62 5.50 3.2670-107-01 1-1/2" 1.25 2.18 4.37 3.06 8.00 4.6170-108-01 2" 1.50 2.34 4.68 3.25 8.00 6.06

70-109-01A 2-1/2" 2.00 3.12 6.25 3.72 8.00 17.2570-100-01 3" 2.50 3.37 6.75 4.12 8.00 18.60

COPYRIGHT ©1997 CONBRACO IND., INC. – PRINTED IN U.S.A.

®70-100 SeriesBronze Ball Valve

Threaded, 600 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: BZ, Style: 3.

FEATURES• Chromium plated ball • Blow-out-proof stem design• RPTFE seats and stuffing box ring • Adjustable packing gland

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 7. Gland nut B162. Stem packing RPTFE 8. Stem B163. Stem bearing RPTFE 9. Lever nut Steel, zinc plated4. Ball B16, chrome plated 10. Body seal PTFE5. Seat (2) RPTFE (1-1/4" to 3")6. Retainer B16 (1/4" to 1") 11. Body B584-C84400

B584-C84400 (1-1/4" to 3")

VARIATIONS AVAILABLE:70-120 Series (Adjustable Stop Lever)70-140 Series (316 SS Ball & Stem)70-150 Series (Balancing Stop)70-190 Series (Locked Retainer)

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/4" to 3"-03- 1-1/4" Stem Extension 1/4" to 3"-04- 2-1/4" Stem Extension 1/4" to 3"-05- Plain Ball 1/4" to 3"-07- Tee Handle 1/4" to 2"-08- 90º Reversed Stem 1/4" to 3"-10- SS Lever & Nut 1/4" to 3"-14- Vented Ball (see page J-2) 1/4" to 3"-15- Round Handle 1/4" to 2"-16- Vertical Chain Lever 3/4" to 2"-17- Rough Chrome Plating 1/4" to 3"-21- UHMWPE Seats (Non-PTFE) 1/4" to 3"-24- Graphite Stem Packing 1/4" to 3"-27- Latch Lock Lever 1/4" to 3"-30- CamLock Handle 1/4" to 2"-32- SS Tee Handle & Nut 1/4" to 2"-35- PTFE Trim 1/4" to 3"-39- SS Latch Lock Wheel Handle 1/4" to 2"-40- Cyl-Loc 1/4" to 2"-41- Auto Drain (See page J-8) 1/4" to 2"-45- Less Lever & Nut 1/4" to 3"-46- Latch Lock Lever - Lock Close Only 1/4" to 3"-47- SS Latch-Lock Oval Handle 1/4" to 1"-48- SS Oval Handle 1/4" to 2"-49- Assembled Dry 1/4" to 3"-50- 2-1/4" Locking Stem Extension 1/4" to 3"-56- Multifill Seats 1/4" to 3"-57- Cleaned for Gaseous Oxygen 1/4" to 3"-58- Horizontal Chain Lever 3/4" to 2"-60- Static Grounded Ball & Stem 1/4" to 3"-63- Threaded x Solder 3/8" to 3"-64- 250 Lb. Steam Trim 1/4" to 3"-P01- BSPP (Parallel) Thread Connection 1/4" to 3"-T01- BSPT (Tapered) Thread Connection 1/4" to 3"

BRONZE BALL VALVE

A-1

For Pressure/Temperature Ratings,Refer to Page N-10, Graph No. 4

1/00


®70-200 SeriesSolder End Bronze Ball Valve

Solder End, 600 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: BZ, Style: 3.


STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 7. Gland nut B162. Stem packing RPTFE 8. Stem B163. Stem bearing RPTFE 9. Lever nut Steel, zinc plated4. Ball B16, chrome plated 10. Body seal PTFE5. Seat (2) RPTFE (1-1/4" to 3")6. Retainer B16 (3/8" to 1") 11. Body B584-C84400

B584-C84400 (1-1/4" to 3")

VARIATIONS AVAILABLE:70-220 Series (Adjustable Stop Lever)70-240 Series (316 SS Ball & Stem)70-250 Series (Balancing Stop)

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 3/8" to 3"-03- 1-1/4" Stem Extension 3/8" to 3"-04- 2-1/4" Stem Extension 3/8" to 3"-05- Plain Ball 3/8" to 3"-07- Tee Handle 3/8" to 2"-08- 90º Reversed Stem 3/8" to 3"-10- SS Lever & Nut 3/8" to 3"-14- Vented Ball (see page J-2) 3/8" to 3"-15- Round Handle 3/8" to 2"-16- Vertical Chain Lever 3/4" to 2"-24- Graphite Stem Packing 3/8" to 3"-27- Latch Lock Lever 3/8" to 3"-32- SS Tee Handle & Nut 3/8" to 2"-35- PTFE Trim 3/8" to 3"-39- SS Latch Lock Wheel Handle 3/8" to 2"-45- Less Lever & Nut 3/8" to 3"-46- Latch Lock Lever - Lock Close Only 3/8" to 3"-47- SS Latch-Lock Oval Handle 3/8" to 1"-48- SS Oval Handle 3/8" to 2"-49- Assembled Dry 3/8" to 3"-50- 2-1/4" Locking Stem Extension 3/8" to 3"-56- Multifill Seats 3/8" to 3"-57- Cleaned for Gaseous Oxygen 3/8" to 3"-58- Horizontal Chain Lever 3/4" to 2"-60- Static Grounded Ball & Stem 3/8" to 3"-63- Threaded x Solder 3/8" to 3"

The 70-200 is designed to be soft soldered into lines withoutdisassembly. This allows a tested valve to be installed withoutdisturbing the seats and seals in any way. Soldering temperaturenot to exceed 500ºF.

NUMBER SIZE A B C D E F G Wt.70-202-01 3/8" .37 1.28 2.56 1.75 3.87 .505 .37 .6370-203-01 1/2" .50 1.43 2.87 1.75 3.87 .630 .50 .7170-204-01 3/4" .68 1.93 3.87 2.12 4.87 .880 .75 1.4470-205-01 1" .87 2.25 4.50 2.25 4.87 1.130 .90 1.9170-206-01 1-1/4" 1.00 2.31 4.62 2.62 5.50 1.380 .96 2.9570-207-01 1-1/2" 1.25 2.62 5.25 3.06 8.00 1.630 1.09 3.9970-208-01 2" 1.50 3.18 6.37 3.25 8.00 2.130 1.34 5.71

70-209-01A 2-1/2" 2.00 3.74 7.51 3.72 8.00 2.630 1.48 15.5370-200-01 3" 2.50 4.12 8.25 4.12 8.00 3.130 1.67 16.74

BRONZE BALL VALVE

A-2


1/00


®70-800 SeriesMale x Female Bronze Ball Valve

Male x Female Threaded, 600 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: BZ, Style: 3.

FEATURES• Chromium plated ball • Blow-out-proof stem design• RPTFE seats and stuffing box ring • Adjustable packing gland• Male x Female threaded end connections

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 7. Gland nut B162. Stem packing RPTFE 8. Stem B163. Stem bearing RPTFE 9. Lever nut Steel, zinc plated4. Ball B16, chrome plated 10. Body seal PTFE5. Seat (2) RPTFE (1-1/4" to 1-1/2")6. Retainer B16 11. Body B584-C84400

VARIATIONS AVAILABLE:70-820 Series (Adjustable Stop Lever)70-840 Series (316 SS Ball & Stem)70-850 Series (Balancing Stop )

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/4" to 1-1/2"-03- 1-1/4" Stem Extension 1/4" to 1-1/2"-04- 2-1/4" Stem Extension 1/4" to 1-1/2"-05- Plain Ball 1/4" to 1-1/2"-07- Tee Handle 1/4" to 1-1/2"-08- 90º Reversed Stem 1/4" to 1-1/2"-10- SS Lever & Nut 1/4" to 1-1/2"-14- Vented Ball (see page J-2) 1/4" to 1-1/2"-15- Round Handle 1/4" to 1-1/2"-16- Vertical Chain Lever 3/4" to 1-1/2"-21- UHMWPE Seats (Non-PTFE) 1/4" to 1-1/2"-24- Graphite Stem Packing 1/4" to 1-1/2"-27- Latch Lock Lever 1/4" to 1-1/2"-30- CamLock Handle 1/4" to 1-1/2"-32- SS Tee Handle & Nut 1/4" to 1-1/2"-35- PTFE Trim 1/4" to 1-1/2"-39- SS Latch Lock Wheel Handle 1/4" to 1-1/2"-40- Cyl-Loc 1/4" to 1-1/2"-41- Auto Drain (see page J-8) 1/4" to 1-1/2"-45- Less Lever & Nut 1/4" to 1-1/2"-46- Latch Lock Lever - Lock Close Only 1/4" to 1-1/2"-47- SS Latch-Lock Oval Handle 1/4" to 1"-48- SS Oval Handle 1/4" to 1-1/2"-49- Assembled Dry 1/4" to 1-1/2"-50- 2-1/4" Locking Stem Extension 1/4" to 1-1/2"-56- Multifill Seats 1/4" to 1-1/2"-57- Cleaned for Gaseous Oxygen 1/4" to 1-1/2"-58- Horizontal Chain Lever 3/4" to 1-1/2"-60- Static Grounded Ball & Stem 1/4" to 1-1/2"-64- 250 Lb. Steam Trim 1/4" to 1-1/2"

NUMBER SIZE A B C D E Wt.70-801-01 1/4" .37 1.40 2.43 1.75 3.87 .6370-802-01 3/8" .37 1.46 2.50 1.75 3.87 .6070-803-01 1/2" .50 1.68 2.81 1.81 3.87 .7270-804-01 3/4" .68 2.00 3.50 2.12 4.87 1.4270-805-01 1" .87 2.31 4.00 2.25 4.87 1.9370-806-01 1-1/4" 1.00 2.31 4.31 2.62 5.50 3.1970-807-01 1-1/2" 1.25 3.00 5.18 3.06 8.00 4.60

MALE X FEMALE BRONZE BALL VALVE

A-3


1/00


®

A-4

71-100 SeriesBronze Ball Valve With Mounting Pad


FEATURES• Chromium plated ball • Blow-out-proof stem design• RPTFE seats and stuffing box ring • Adjustable packing gland• Mounting pad for easy actuator mounting

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 9. Lever nut Steel, zinc plated2. Stem packing RPTFE 10. Body seal PTFE3. Stem bearing RPTFE (1-1/4" to 3")4. Ball B16, chrome plated 11. Body B584-C844005. Seat (2) RPTFE6. Retainer B16 (3/4" to 1")

B584-C84400 (1-1/4" to 3")7. Gland nut B168. Stem B16

VARIATIONS AVAILABLE:71-120 Series (Adjustable Stop Lever)71-140 Series (316 SS Ball & Stem)71-150 Series (Balancing Stop)71-190 Series (Locked Retainer)

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 3/4" to 3"-03- 1-1/4" Stem Extension 3/4" to 3"-04- 2-1/4" Stem Extension 3/4" to 3"-05- Plain Ball 3/4" to 3"-07- Tee Handle 3/4" to 2"-08- 90º Reversed Stem 3/4" to 3"-10- SS Lever & Nut 3/4" to 3"-14- Vented Ball (see page J-2) 3/4" to 3"-15- Round Handle 3/4" to 2"-16- Vertical Chain Lever 3/4" to 2"-21- UHMWPE Seats (Non-PTFE) 3/4" to 3"-24- Graphite Stem Packing 3/4" to 3"-27- Latch Lock Lever 3/4" to 3"-30- CamLock Handle 3/4" to 2"-32- SS Tee Handle & Nut 3/4" to 2"-35- PTFE Trim 3/4" to 3"-39- SS Latch Lock Wheel Handle 3/4" to 2"-40- Cyl-Loc 3/4" to 2"-41- Auto Drain (see page J-8) 3/4" to 2"-45- Less Lever & Nut 3/4" to 3"-46- Latch Lock Lever - Lock Close Only 3/4" to 3"-47- SS Latch-Lock Oval Handle 3/4" to 1"-48- SS Oval Handle 3/4" to 2"-49- Assembled Dry 3/4" to 3"-50- 2-1/4" Locking Stem Extension 3/4" to 3"-56- Multifill Seats 3/4" to 3"-57- Cleaned for Gaseous Oxygen 3/4" to 3"-58- Horizontal Chain Lever 3/4" to 2"-60- Static Grounded Ball & Stem 3/4" to 3"-64- 250 Lb. Steam Trim 3/4" to 3"-P01- BSPP (Parallel) Thread Connection 3/4" to 3"-T01- BSPT (Tapered) Thread Connection 3/4" to 3"NUMBER SIZE A B C D E F G H Wt.

71-104-01 3/4" .68 1.50 3.00 2.12 4.87 .87 1.37 10-24 NC 1.6371-105-01 1" .87 1.68 3.37 2.25 4.87 .87 1.37 10-24 NC 1.8671-106-01 1-1/4" 1.00 2.00 4.00 2.62 5.50 .93 1.50 1/4-20 NC 3.3971-107-01 1-1/2" 1.25 2.18 4.37 2.87 8.00 .93 1.50 1/4-20 NC 4.6871-108-01 2" 1.50 2.34 4.68 3.06 8.00 .93 1.50 1/4-20 NC 5.7271-100-01 3" 2.50 3.37 6.75 4.12 8.00 N/A 2.75 1/4-20 NC 18.60

BRONZE BALL VALVE WITH MOUNTING PAD


1/00

*See 77-140 Series Full Port for 1/4", 3/8", 1/2" and 2-1/2" Sizes

COPYRIGHT ©1999 CONBRACO IND., INC. – PRINTED IN U.S.A. A-5

® 71-ARX SeriesBronze Std. Port Ball Valve with

Actuator Ready ISO Mounting PadThreaded, 600 psig WOG, Cold Non-Shock, 250 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: BZ, Style: 3.

FEATURES• Multi-piece packing set • Blow-out-proof stem design• ISO 5211 mounting pad • Adjustable packing gland• Stainless ball & stem • Live loaded packing

STANDARD MATERIAL LIST1. Stem packing MPTFE 6. Gland B162. Stem bearing RPTFE 7. Stem 316 SS3. Ball 316 SS 8. Jam nut SS4. Seat (2) MPTFE 9. Body seal PTFE (1-1/4" to 3")

B16 (3/4" to 1")5. Retainer B584-C84400 (1-1/4" to 3") 10. Body B584-C84400

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-14- Vented Ball 3/4" to 3"-24- Graphite Stem Packing 3/4" to 2"-27- Latch Lock Handle 3/4" to 3"-35- PTFE Seats 3/4" to 3"-57- Oxygen Cleaned 3/4" to 3"

KJ (THRDS.) WT.

NUMBER SIZE A B C D E F G H I (FLATS) UNF

71-AR4-64 3/4" .68 1.50 3.00 2.16 .70 1.39 .28 .84 .37 .247/.249 3/8-24 1.38

71-AR5-64 1" .87 1.68 3.37 2.28 .70 1.39 .28 .84 .37 .247/.249 3/8-24 1.76

71-AR6-64 1-1/4" 1.00 1.98 3.97 3.16 .98 1.95 .34 1.16 .54 .370/.372 5/8-18 3.51

71-AR7-64 1-1/2" 1.25 2.18 4.37 3.16 .98 1.95 .34 1.16 .58 .370/.372 5/8-18 4.40

71-AR8-64 2" 1.50 2.34 4.68 3.37 .98 1.95 .34 1.16 .55 .370/.372 5/8-18 5.89

71-AR9-64 2-1/2" 2.00 3.12 6.25 3.85 .98 1.95 .34 1.16 .54 .370/.372 5/8-18 14.12

71-AR0-64 3" 2.50 3.37 6.75 4.18 .98 1.95 .34 1.16 .54 .370/.372 5/8-18 18.55

BRONZE STD. PORT BALL VALVE WITH ISO MOUNTING PAD


1/00

A-6 COPYRIGHT ©1997 CONBRACO IND., INC. – PRINTED IN U.S.A.

®72-100 SeriesCarbon Steel High Pressure Ball Valve

Threaded, 3000 psig WOG, Cold Non-Shock Body rating (see P/T Chart referenced below for seat rating).150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: CS, Style: 3.

FEATURES• Barstock design • Adjustable packing gland• RPTFE seats and stuffing box ring • Full port, except 2"• Fire safe design when ordered with • Blow-out-proof stem design

graphite packing • Heavy duty lever• Nitride corrosion protection

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 7. Gland nut A108-CS2. Stem A108-CS chrome plated 8. Stem packing RPTFE3. Stem bearing RPTFE 9. Lever nut Steel, zinc plated4. Retainer seal RPTFE 10. Body A108-CS5. Seat (2) RPTFE 11. Retainer A108-CS6. Ball A108-CS chrome plated 12. Seat holder A108-CS

VARIATIONS AVAILABLE:72-140 Series (316 SS Ball & Stem)

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/2" to 2"-03- 1-1/4" Stem Extension 1" to 1-1/2"-04- 2-1/4" Stem Extension 1" to 1-1/2"-07- Tee Handle 1/2" to 1-1/2"-08- 90º Reversed Stem 1/2" to 2"-10- SS Lever & Nut 1/2" to 1-1/2"-14- Vented Ball (see page J-2) 1/2" to 2"-15- Round Handle 1/2" to 1"-19- Lock Plate 1/2" to 2"-21- UHMWPE Seats (Non-PTFE) 1/2" to 2"-24- Graphite Stem Packing 1/2" to 2"-45- Less Lever & Nut 1/2" to 2"-56- Multifill Seats 1/2" to 2"-60- Static Grounded Ball & Stem 1/2" to 2"-64- 250 Lb. Steam Trim 1/2" to 2"

NUMBER SIZE A B C D E Wt.72-103-01 1/2" .62 1.46 2.87 2.50 5.62 1.9872-104-01 3/4" .81 1.87 3.71 2.62 5.62 3.0972-105-01 1" 1.00 2.12 4.15 3.12 6.62 4.8772-106-01 1-1/4" 1.25 2.32 4.65 3.43 8.00 7.6772-107-01 1-1/2" 1.50 2.64 5.23 3.56 8.00 10.5072-108-01 2" 1.75 3.00 5.84 4.18 9.00 15.26

CARBON STEEL HIGH PRESSURE BALL VALVE


1/00


®72-900 SeriesCarbon Steel SAE Straight Thread Ball Valve

Threaded, 3000 psig WOG, Cold Non-Shock Body Rating (see P/T Chart referenced below for seat rating).150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: CS, Style: 3.

FEATURES• Barstock design • Adjustable packing gland• RPTFE seats and stuffing box ring • Full port, except 2"• Fire safe design when ordered with • Blow-out-proof stem design

graphite packing • Heavy duty lever• Nitride corrosion protection • SAE J512/J514 Straight Thread O-Ring Boss

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 7. Gland nut A108-CS2. Stem A108-CS chrome plated 8. Stem packing RPTFE3. Stem bearing RPTFE 9. Lever nut Steel, zinc plated4. Retainer seal RPTFE 10. Body A108-CS5. Seat (2) RPTFE 11. Retainer A108-CS6. Ball A108-CS chrome plated 12. Seat holder A108-CS


OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/4" to 2"-03- 1-1/4" Stem Extension 1" to 1-1/2"-04- 2-1/4" Stem Extension 1" to 1-1/2"-07- Tee Handle 1/4" to 1-1/2"-08- 90º Reversed Stem 1/4" to 2"-10- SS Lever & Nut 1/4" to 1-1/2"-14- Vented Ball (see page J-2) 1/4" to 2"-15- Round Handle 1/4" to 1"-19- Lock Plate 1/4" to 2"-21- UHMWPE Seats (Non-PTFE) 1/4" to 2"-24- Graphite Stem Packing 1/4" to 2"-45- Less Lever & Nut 1/4" to 2"-56- Multifill Seats 1/4" to 2"-60- Static Grounded Ball & Stem 1/4" to 2"-64- 250 Lb. Steam Trim 1/4" to 2"

NOM.NUMBER TUBE SIZE A B C D E Wt.

O.D.72-901-01 1/4" 7/16"-20 .39 1.46 2.84 2.50 5.62 2.0972-902-01 3/8" 9/16"-18 .51 1.46 2.84 2.50 5.62 2.0672-903-01 1/2" 3/4"-16 .62 1.46 2.84 2.50 5.62 2.5672-904-01 3/4" 1-1/16"-12 .81 1.87 3.71 2.62 5.62 3.0772-905-01 1" 1-5/16"-12 1.00 2.12 4.15 3.12 6.62 4.9172-906-01 1-1/4" 1-5/8"-12 1.25 2.32 4.65 3.43 8.00 7.7372-907-01 1-1/2" 1-7/8"-12 1.50 2.64 5.23 3.56 8.00 10.2172-908-01 2" 2-1/2"-12 1.75 3.00 5.84 4.18 9.00 14.88

CARBON STEEL SAE STRAIGHT THREADO-RING BOSS BALL VALVE

A-7


1/00


®73-100 SeriesCarbon Steel Ball Valve

Threaded, 1/4" to 1" 2000 psig WOG, 1-1/4" to 2" 1500 psig WOG. Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: CS, Style: 3.

FEATURES• Barstock design • Adjustable packing gland• RPTFE seats and stuffing box ring • Blow-out-proof stem design• Fire safe design when ordered with • Nitride corrosion protection

graphite packing

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 7. Gland nut A108-CS2. Stem packing RPTFE 8. Stem A108-CS3. Stem bearing RPTFE 9. Lever nut Steel, zinc plated4. Ball A108-CS chrome plated 10. Body seal PTFE5. Seat (2) RPTFE (1-1/4" to 2")6. Retainer A108-CS 11. Body A108-CS

VARIATIONS AVAILABLE:73-140 Series (316 SS Ball & Stem)73-160 Series (NACE Trim)

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/4" to 2"-03- 1-1/4" Stem Extension 1/4" to 2"-04- 2-1/4" Stem Extension 1/4" to 2"-06- 2000 psig WOG 1-1/4" to 2"-07- Tee Handle 1/4" to 1-1/2"-08- 90º Reversed Stem 1/4" to 2"-10- SS Lever & Nut 1/4" to 2"-14- Vented Ball (see page J-2) 1/4" to 2"-15- Round Handle 1/4" to 1-1/2"-19- Lock Plate 1/4" to 2"-24- Graphite Stem Packing 1/4" to 2"-44- Seal Welded 1/4" to 2"-45- Less Lever & Nut 1/4" to 2"-56- Multifill Seats 1/4" to 2"-60- Static Grounded Ball & Stem 1/4" to 2"-64- 250 Lb. Steam Trim 1/4" to 2"-P01- BSPP (Parallel) Thread Connection 1/4" to 2"-T01- BSPT (Tapered) Thread Connection 1/4" to 2"


CARBON STEEL BALL VALVE For Pressure/Temperature Ratings,Refer to Page N-15, Graph No. 13 (1/4"

to 1")Refer to Page N-14, Graph No. 11

(1-1/4" to 2")

A-9COPYRIGHT ©1999 CONBRACO IND., INC. – PRINTED IN U.S.A.

® 73A-100 SeriesCarbon Steel Ball Valve

AAR Approved #E999032

Threaded, 2000 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: CS, Style: 3.

FEATURES• RPTFE seats & packing • Blow-out-proof stem design• Actuator mounting pads • Adjustable packing gland• Forged construction • Nitride corrosion protection• Raised handle stops • (-24) Fire safe to API 607 4th ed. class 600 burn

STANDARD MATERIAL LIST1. Lever nut Steel, zinc plated 6. Ball A108-CS chrome plated2. Gland nut A108-CS 7. Seat (2) RPTFE3. Stem packing RPTFE 8. Body A1054. Retainer A108-CS 9. Stem bearing RPTFE5. Body seal RPTFE (1/2" to 2") 10. Stem A108-CS

11. Lever/grip Steel, zinc plated,with vinyl

VARIATIONS AVAILABLE: 73A-140- Series (316 SS Ball & Stem)(NACE compliant)

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/4" to 2"-03- 1-1/4" Stem Extension 1/4" to 2"-04- 2-1/4" Stem Extension 1/4" to 2"-07- Tee Handle 1/4" to 1-1/2"-08- 90º Reversed Stem 1/4" to 2"-10- SS Lever & Nut 1/4" to 2"-14- Vented ball 1/4" to 2"-15- Round Handle 1/4" to 1-1/2"-24- Graphite Stem Packing 1/4" to 2"-27- Latch Lock Lever 1/4" to 2"-44- Seal welded 1/4" to 2"-45- Less Lever & Nut 1/4" to 2"-56- Multi-fill Seats 1/4" to 2"-60- Static Grounded Ball & Stem 1/4" to 2"-64- 250 Lb. Steam Trim 1/4" to 2"-71- Actuator Mtg. Drilled & Tapped 1/4" to 2"-P01- BSPP (Parallel) Thread Conn. 1/4" to 2"-T01- BSPT (Tapered) Thread Conn. 1/4" to 2"

NUMBER SIZE A B C D E73A-101-01 1/4" .37 1.02 2.53 1.72 3.8573A-102-01 3/8" .37 1.02 2.53 1.72 3.8573A-103-01 1/2" .50 1.18 2.29 1.78 3.8573A-104-01 3/4" .68 1.57 3.07 2.07 4.7573A-105-01 1" .87 1.73 3.40 2.18 4.7573A-106-01 1-1/4" 1.00 1.98 3.97 2.72 5.5073A-107-01 1-1/2" 1.25 2.14 4.32 3.12 7.7573A-108-01 2" 1.50 2.73 5.44 3.27 7.75

CARBON STEEL BALL VALVEFor Pressure/Temperature Ratings,

Refer to Page N-15, Graph No. 13

1/00


®76-100 SeriesStainless Steel Ball Valve

Threaded, 1/4" to 1" 2000 psig WOG, 1-1/4" to 2" 1500 psig WOG, 2-1/2" to 3" 1000 psig WOGCold Non-Shock. 150 psig Saturated Steam, Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: SS, Style: 3.

FEATURES• Investment cast components • Adjustable packing gland• RPTFE seats and stuffing box ring • Meets NACE MR-01-75• Mounting pad for easy actuator mounting • SS lever and nut• Blow-out-proof stem design • (-24) 1/4" to 2" Certified to API 607,

4th Edition, Class 600 burn

STANDARD MATERIAL LIST1. Lever and grip 304 SS w/vinyl 7. Gland nut A276-3162. Stem packing RPTFE 8. Stem A276-3163. Stem bearing RPTFE 9. Lever nut 18-8 SS4. Ball A276-316 10. Body seal PTFE5. Seat (2) RPTFE (1-1/4" to 3")6. Retainer A276-316 (1/4" to 1") 11. Body A351-CF8M

A351-CF8M (1-1/4" to 3")OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/4" to 3"-03- 1-1/4" Stem Extension 1/4" to 3"-04- 2-1/4" Stem Extension 1/4" to 3"-07- Tee Handle 1/4" to 2"-08- 90º Reversed Stem 1/4" to 3"-14- Vented Ball (see page J-2) 1/4" to 2"-15- Round Handle 1/4" to 2"-16- Vertical Chain Lever 3/4" to 2"-19- Lock Plate 1/4" to 2"-21- UHMWPE Seats (Non-PTFE) 1/4" to 3"-24- Graphite Stem Packing 1/4" to 3"-27- Latch Lock Lever 1/4" to 3"-30- CamLock Handle 1/4" to 2"-32- SS Tee Handle & Nut 1/4" to 2"-35- PTFE Trim 1/4" to 3"-39- SS Latch Lock Wheel Handle 1/4" to 2"-40- Cyl-Loc 1/4" to 2"-44- Seal Welded 1/4" to 2"-45- Less Lever & Nut 1/4" to 3"-46- Latch Lock Lever - Lock Close Only 1/4" to 3"-47- SS Latch Lock Oval Handle 1/4" to 1"-48- SS Oval Handle 1/4" to 2"-49- Assembled Dry 1/4" to 3"-50- 2-1/4" Locking Stem Extension 1/4" to 3"-57- Cleaned For Gaseous Oxygen 1/4" to 3"-58- Horizontal Chain Lever 3/4" to 2"-60- Static Grounded Ball & Stem 1/4" to 3"-64- 250 Lb. Steam Trim 1/4" to 3"-P01- BSPP (Parallel) Thread Connection 1/4" to 3"-T01- BSPT (Tapered) Thread Connection 1/4" to 3"

NUMBER SIZE A B C D E F G Wt.76-101-01 1/4" .37 1.03 2.06 1.75 3.87 .50 1.12 .5876-102-01 3/8" .37 1.03 2.06 1.75 3.87 .50 1.12 .5476-103-01 1/2" .50 1.12 2.25 1.81 3.87 .50 1.12 .6376-104-01 3/4" .68 1.50 3.00 2.12 4.87 .87 1.37 1.2776-105-01 1" .87 1.68 3.37 2.25 4.87 .87 1.37 1.6376-106-01 1-1/4" 1.00 2.00 4.00 2.62 5.50 .93 1.50 3.0676-107-01 1-1/2" 1.25 2.18 4.37 3.05 8.00 .93 1.50 4.0476-108-01 2" 1.50 2.75 5.50 3.24 8.00 .93 1.50 6.0576-109-01 2-1/2" 2.50 3.37 6.75 4.12 8.00 2.75 3.37 15.5776-100-01 3" 2.50 3.37 6.75 4.12 8.00 2.75 3.37 16.79

STAINLESS STEEL BALL VALVE

For Pressure/Temperature Ratings,Refer to Page N-15, Graph No. 14 (1/4"


(1-1/4" to 2")Refer to Page N-12, Graph No. 8

(2-1/2" to 3")

1/00


76-ARX SeriesStainless Steel Std. Port Ball Valve with

Actuator Ready ISO Mounting PadThreaded, 1/4"-1" 2000 psig WOG, 1-1/4"-2" 1500 psig WOG, 2-1/2"-3"1000 psig WOG, Cold Non-Shock. 250 psig Saturated Steam. Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: SS, Style: 3.

FEATURES• Multi-piece packing set • Blow-out-proof stem design• ISO 5211 mounting pad • Adjustable packing gland

• Live loaded packing

STANDARD MATERIAL LIST1. Stem packing MPTFE 6. Gland A276-3162. Stem bearing RPTFE 7. Stem A276-3163. Ball 316 SS 8. Jam nut SS4. Seat (2) MPTFE 9. Body seal PTFE (1-1/4" to 3")5. Retainer A276-316 (1/4" to 1") 10. Body A351-CF8M

A351-CF8M (1-1/4" to 3")



(1/4" to 1")Refer to Page N-14, Graph No. 12


(2-1/2" to 3")

KJ (THRDS.) WT.


76-AR1-64 1/4" .37 1.03 2.06 1.40 .59 1.17 .28 .61 .23 .247/.249 3/8-24 .52

76-AR2-64 3/8" .37 1.03 2.06 1.40 .59 1.17 .28 .61 .23 .247/.249 3/8-24 .48

76-AR3-64 1/2" .50 1.12 2.25 1.54 .59 1.17 .28 .61 .21 .247/.249 3/8-24 .58

76-AR4-64 3/4" .68 1.50 3.00 2.16 .70 1.39 .28 .84 .37 .247/.249 3/8-24 1.26

76-AR5-64 1" .87 1.68 3.37 2.28 .70 1.39 .28 .84 .37 .247/.249 3/8-24 1.62

76-AR6-64 1-1/4" 1.00 1.98 3.97 3.16 .98 1.95 .34 1.16 .54 .370/.372 5/8-18 3.22

76-AR7-64 1-1/2" 1.25 2.18 4.37 3.16 .98 1.95 .34 1.16 .58 .370/.372 5/8-18 4.06

76-AR8-64 2" 1.50 2.75 5.50 3.37 .98 1.95 .34 1.16 .55 .370/.372 5/8-18 6.18

76-AR9-64 2-1/2" 2.00 3.12 6.25 3.85 .98 1.95 .34 1.16 .54 .370/.372 5/8-18 12.96

76-AR0-64 3" 2.50 3.37 6.75 4.18 .98 1.95 .34 1.16 .54 .370/.372 5/8-18 17.06

STAINLESS STEEL STD. PORT BALL VALVE WITH ISO MOUNTING PAD

®

1/00


®77-100 SeriesBronze Full Port Ball Valve


FEATURES• Chromium plated ball • Blow-out-proof stem design• RPTFE seats and stuffing box ring • Adjustable packing gland• Mounting pad for easy actuator mounting • Full port for full flow & min. pressure drop

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 10. Body seal PTFE (1-1/4" to 2-1/2")2. Stem packing RPTFE 11. Body B584-C844003. Stem bearing RPTFE4. Ball B16, chrome plated5. Seat (2) RPTFE6. Retainer B16 (1/4" to 1")

B584-C84400 (1-1/4" to 2-1/2")7. Gland nut B168. Stem B169. Lever nut Steel, zinc plated

VARIATIONS AVAILABLE:77-140 Series (316 SS Ball & Stem)77-150 Series (Original Balancing Stop)77-190 Series (Locked Retainer)

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/4" to 2-1/2"-03- 1-1/4" Stem Extension 1/4" to 2-1/2"-04- 2-1/4" Stem Extension 1/4" to 2-1/2"-05- Plain Ball 1/4" to 2-1/2"-07- Tee Handle 1/4" to 1-1/4"-08- 90º Reversed Stem 1/4" to 2-1/2"-10- SS Lever & Nut 1/4" to 2-1/2"-14- Vented Ball (see page J-2) 1/4" to 2-1/2"-15- Round Handle 1/4" to 1-1/4"-16- Vertical Chain Lever 3/4" to 2-1/2"-17- Rough Chrome Plating 1/4" to 2-1/2"-18- Plain Yellow Grip 1/4" to 2-1/2"-20- Slot Vented Ball 1/4" to 2-1/2"-24- Graphite Stem Packing 1/4" to 2-1/2"-27- Latch Lock Lever 1/4" to 2-1/2"-28- Mounting Pad Not Drilled 1/4" to 2-1/2"

& Tapped-30- CamLock Handle 1/4" to 1-1/4"-32- SS Tee Handle & Nut 1/4" to 1-1/4"-35- PTFE Trim 1/4" to 2-1/2"-36- SS High-Rise Round Handle & Nut 1/4" to 1-1/4"-40- Cyl-Loc 1/4" to 1-1/4"-45- Less Lever & Nut 1/4" to 2-1/2"-46- Latch Lock Lever - Lock Close Only 1/4" to 2-1/2"-47- SS Latch-Lock Oval Handle 1/4" to 3/4"-48- SS Oval Handle 1/4" to 2"-49- Assembled Dry 1/4" to 2-1/2"-50- 2-1/4" Locking Stem Extension 1/4" to 2-1/2"-56- Multifill Seats 1/4" to 2-1/2"-57- Cleaned For Gaseous Oxygen 1/4" to 2-1/2"-58- Horizontal Chain Lever 3/4" to 2-1/2"-60- Static Grounded Ball & Stem 1/4" to 2-1/2"-63- Threaded x Solder 1/4" to 2-1/2"-64- 250 Lb. Steam Trim 1/4" to 2-1/2"-P01- BSPP (Parallel) Thread Connection 1/4" to 2-1/2"-T01- BSPT (Tapered) Thread Connection 1/4" to 2-1/2"

NUMBER SIZE A B C D E F G Wt.77-101-01 1/4" .43 1.12 2.25 1.81 3.87 .50 1.12 .7977-102-01 3/8" .50 1.12 2.25 1.81 3.87 .50 1.12 .7577-103-01 1/2" .50 1.12 2.25 1.81 3.87 .50 1.12 .6977-104-01 3/4" .81 1.56 3.12 2.12 4.87 .87 1.37 1.8377-105-01 1" 1.00 1.81 3.62 2.62 5.50 .93 1.50 3.3277-106-01 1-1/4" 1.25 2.12 4.25 2.87 5.50 .93 1.50 5.0577-107-01 1-1/2" 1.50 2.37 4.75 3.34 8.00 2.08 3.06 6.7177-108-01 2" 2.00 2.65 5.37 3.71 8.00 2.41 3.52 11.7577-109-01 2-1/2" 2.50 3.25 6.50 4.12 8.00 2.75 3.37 17.25

BRONZE FULL PORT BALL VALVE


1/00


® 77-ARX SeriesCarbon Steel Full Port Ball Valve with

Actuator Ready ISO Mounting PadThreaded, 1/4"-1" 2000 psig WOG, 1-1/4"-2" 1500 psig WOG, 2-1/2"-3"1000 psig WOG, Cold Non-Shock. 150 psig Saturated Steam. Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: CS, Style: 3.


STANDARD MATERIAL LIST1. Stem packing MPTFE 6. Gland A276-3162. Stem bearing RPTFE 7. Stem A276-3163. Ball 316 SS 8. Jam nut SS4. Seat (2) MPTFE 9. Body seal PTFE (1-1/4" to 3")5. Retainer A108-CS (1/4" to 3") 10. Body A216-WCB



KJ (THRDS.) WT.


77-AR1-64 1/4" .37 1.03 2.06 1.40 .59 1.17 .28 .61 .23 .247/.249 3/8-24 .60

77-AR2-64 3/8" .37 1.03 2.06 1.40 .59 1.17 .28 .61 .23 .247/.249 3/8-24 .57

77-AR3-64 1/2" .50 1.12 2.25 1.54 .59 1.17 .28 .61 .21 .247/.249 3/8-24 .62

77-AR4-64 3/4" .68 1.50 3.00 2.16 .70 1.39 .28 .84 .37 .247/.249 3/8-24 1.76

77-AR5-64 1" .87 1.68 3.37 2.28 .70 1.39 .28 .84 .37 .247/.249 3/8-24 3.44

77-AR7-64 1-1/2" 1.25 2.18 4.37 3.16 .98 1.95 .34 1.16 .58 .370/.372 5/8-18 6.25

77-AR8-64 2" 1.50 2.75 5.50 3.37 .98 1.95 .34 1.16 .55 .370/.372 5/8-18 11.72

CARBON STEEL STD. PORT BALL VALVE WITH ISO MOUNTING PAD

1/00

A-14

BRONZE FULL PORT SOLDER END BALL VALVE


®77-200 SeriesBronze Full Port Solder End Ball Valve

Solder End, 600 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: BZ, Style: 3.

FEATURES• Chromium plated ball • Blow-out-proof stem design• RPTFE seats and stuffing box ring • Adjustable packing gland• Full port for full flow & min. pressure drop

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 7. Gland nut B162. Stem packing RPTFE 8. Stem B163. Stem bearing RPTFE 9. Lever nut Steel, zinc plated4. Ball B16 chrome plated 10. Body seal PTFE5. Seat (2) RPTFE (1-1/4" to 2-1/2")6. Retainer B16 (3/4" to 1") 11. Body B584-C84400

B584-C84400 (1-1/4" to 2-1/2")

VARIATIONS AVAILABLE:77-240 Series (316 SS Ball & Stem)77-250 Series (Balancing Stop)

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 3/4" to 2-1/2"-03- 1-1/4" Stem Extension 3/4" to 2-1/2"-04- 2-1/4" Stem Extension 3/4" to 2-1/2"-05- Plain Ball 3/4" to 2-1/2"-07- Tee Handle 3/4" to 1-1/4"-08- 90º Reversed Stem 3/4" to 2-1/2"-10- SS Lever & Nut 3/4" to 2-1/2"-14- Vented Ball (see page J-2) 3/4" to 2-1/2"-15- Round Handle 3/4" to 1-1/4"-16- Vertical Chain Lever 3/4" to 2-1/2"-17- Rough Chrome Plating 3/4" to 2-1/2"-20- Slot Vented Ball 3/4" to 2-1/2"-24- Graphite Stem Packing 3/4" to 2-1/2"-27- Latch Lock Lever 3/4" to 2-1/2"-30- CamLock Handle 3/4" to 1-1/4"-32- SS Tee Handle & Nut 3/4" to 1-1/4"-35- PTFE Trim 3/4" to 2-1/2"-40- Cyl-Loc 3/4" to 1-1/4"-45- Less Lever & Nut 3/4" to 2-1/2"-46- Latch Lock Lever - Lock Close Only 3/4" to 2-1/2"-47- SS Latch-Lock Oval Handle 3/4" ONLY-48- SS Oval Handle 3/4" to 2-1/2"-49- Assembled Dry 3/4" to 2-1/2"-50- 2-1/4" Locking Stem Extension 3/4" to 2-1/2"-56- Multifill Seats 3/4" to 2-1/2"-57- Cleaned For Gaseous Oxygen 3/4" to 2-1/2"-58- Horizontal Chain Lever 3/4" to 2-1/2"-60- Static Grounded Ball & Stem 3/4" to 2-1/2"-63- Threaded x Solder 3/4" to 2-1/2"

NUMBER SIZE A B C D E F G Wt.77-204-01 3/4" .81 2.12 4.12 2.12 4.87 .878 .75 1.6577-205-01 1" 1.00 2.33 4.64 2.62 5.50 1.129 .90 2.9977-206-01 1-1/4" 1.25 2.60 5.15 2.87 5.50 1.378 .96 4.5577-207-01 1-1/2" 1.50 3.00 6.00 3.34 8.00 1.629 1.09 6.0477-208-01 2" 2.00 3.62 7.24 3.71 8.00 2.129 1.34 10.5877-209-01 2-1/2" 2.50 3.93 7.87 4.12 8.00 2.630 1.48 15.53

The 77-200 is designed to be soft solderedinto lines without disassembly. This allowsa tested valve to be installed withoutdisturbing the seats and seals in any way.Soldering temperature not to exceed 500ºF.


1/00


® 77-900 SeriesBronze Full Port SAE Straight Thread Ball Valve

Straight Threads, 600 psig WOG, Cold Non-Shock. 150 psig Saturated Steam. Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: BZ, Style: 3.

FEATURES• Chromium plated ball • Blow-out-proof stem design• RPTFE seats and stuffing box ring • Adjustable packing gland• Mounting pad for easy actuator mounting • Full port for full flow & min. pressure drop• Straight thread w/O-Ring boss connection • SAE J512/J514 Straight Thread O-Ring Boss

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 7. Gland nut B162. Stem packing RPTFE 8. Stem B163. Stem bearing RPTFE 9. Lever nut Steel, zinc plated4. Ball Brass, chrome plated 10. Body seal PTFE (1-1/4" to 2")5. Seat (2) RPTFE 11. Body B584-C844006. Retainer B16 (1/4" to 1")

B584-C84400 (1-1/4" to 2")

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/4" to 2"-03- 1-1/4" Stem Extension 1/4" to 2"-04- 2-1/4" Stem Extension 1/4" to 2"-07- Tee Handle 1/4" to 2"-08- 90º Reversed Stem 1/4" to 2"-10- SS Lever & Nut 1/4" to 2"-15- Round Handle 1/4" to 2"-17- Rough Chrome Plating 1/4" to 2"-24- Graphite Stem Packing 1/4" to 2"-27- Latch Lock Lever 1/4" to 2"-30- CamLock Handle 1/4" to 2"-32- SS Tee Handle & Nut 1/4" to 2"-35- PTFE Trim 1/4" to 2"-46- Latch Lock Lever - Lock Close Only 1/4" to 3"-48- SS Oval Handle 1/4" to 2"-50- 2-1/4" Locking Stem Extension 1/4" to 2"

NOM.NUMBER TUBE SIZE A B C D E F G Wt.

O.D.77-901-01 1/4" 7/16"-20 .43 1.12 2.25 1.81 3.87 .50 1.12 .7977-902-01 3/8" 9/16"-18 .50 1.12 2.25 1.81 3.87 .50 1.12 .7577-903-01 1/2" 3/4"-16 .50 1.12 2.25 1.81 3.87 .50 1.12 .6977-904-01 3/4" 1-1/16"-12 .81 1.56 3.12 2.12 4.87 .87 1.37 1.8377-905-01 1" 1-5/16"-12 1.00 1.81 3.62 2.62 5.50 .93 1.50 3.3277-906-01 1-1/4" 1-5/8"-12 1.25 2.12 4.25 2.87 5.50 .93 1.50 5.0577-907-01 1-1/2" 1-7/8"-12 1.50 2.37 4.75 3.34 8.00 2.09 3.06 6.7177-908-01 2" 2-1/2"-12 2.00 2.65 5.37 3.71 8.00 2.41 3.52 11.75

BRONZE FULL PORT SAE O-RING BOSS BALL VALVE



®89-100 SeriesCarbon Steel Ball Valve

NPT Threaded, 1/4" to 1" 2000 psig WOG, 1-1/4" to 2" 1500 psig WOG, 2-1/2" to 3" 1000 psig WOGCold Non-Shock. 150 psig Saturated Steam. Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: CS, Style: 3.Complies with MSS SP-110

FEATURES• Investment cast components • Blow-out-proof stem design• RPTFE seats and stuffing box ring • Adjustable packing gland• Mounting pad for easy actuator mounting • Nitride corrosion protection• (-24) Certified to API 607, 4th, Edition, Class 600 burn

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 9. Lever nut Steel, zinc plated2. Stem packing RPTFE 10. Body seal PTFE (1-1/4" to 3")3. Stem bearing RPTFE 11. Body A216-WCB4. Ball A108-CS chrome plated5. Seat (2) RPTFE6. Retainer A108 CS (1/4" to 1")

A216-WCB (1-1/4" to 3")7. Gland nut A108-CS8. Stem A108-CS

VARIATIONS AVAILABLE:89-140 Series (316 SS Ball & Stem)89-190 Series (Locked Retainer)

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/4" to 3"-03- 1-1/4" Stem Extension 1/4" to 3"-04- 2-1/4" Stem Extension 1/4" to 3"-07- Tee Handle 1/4" to 2"-08- 90º Reversed Stem 1/4" to 3"-10- SS Lever & Nut 1/4" to 3"-14- Vented Ball (see page J-2) 1/4" to 3"-15- Round Handle 1/4" to 2"-16- Vertical Chain Lever 3/4" to 2"-18- Plain Yellow Grip 1/4" to 3"-19- Lock Plate 1/4" to 2"-24- Graphite Stem Packing 1/4" to 3"-27- Latch Lock Lever 1/4" to 3"-30- CamLock Handle 1/4" to 2"-32- SS Tee Handle & Nut 1/4" to 2"-35- PTFE Trim 1/4" to 3"-39- SS Latch Lock Wheel Handle 1/4" to 2"-40- Cyl-Loc 1/4" to 2"-44- Seal Welded 1/4" to 2"-45- Less Lever & Nut 1/4" to 3"-46- Latch Lock Lever - Lock Close Only 1/4" to 3"-47- SS Latch-Lock Oval Handle 1/4" to 1"-48- SS Oval Handle 1/4" to 2"-50- 2-1/4" Locking Stem Extension 1/4" to 3"-56- Multifill Seats 1/4" to 3"-58- Horizontal Chain Lever 3/4" to 2"-60- Static Grounded Ball & Stem 1/4" to 3"-64- 250 Lb. Steam Trim 1/4" to 3"-P01- BSPP (Parallel) Thread Connection 1/4" to 3"-T01- BSPT (Tapered) Thread Connection 1/4" to 3"


CARBON STEEL BALL VALVE



(1-1/4" to 2")

1/00


® 89-ARX SeriesCarbon Steel Std. Port Ball Valve with

Actuator Ready ISO Mounting PadThreaded, 1/4"-1" 2000 psig WOG, 1-1/4"-2" 1500 psig WOG, 2-1/2"-3"1000 psig WOG, Cold Non-Shock. 250 psig Saturated Steam. Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: CS, Style: 3.


STANDARD MATERIAL LIST1. Stem packing MPTFE 6. Gland A276-3162. Stem bearing RPTFE 7. Stem A276-3163. Ball 316 SS 8. Jam nut SS4. Seat (2) MPTFE 9. Body seal PTFE (1-1/4" to 3")5. Retainer A108-CS (1/4" to 3") 10. Body A216-WCB



(1/4" to 1")Refer to Page N-14, Graph No. 12


(2-1/2" to 3")

KJ (THRDS.) WT.


89-AR1-64 1/4" .37 1.03 2.06 1.40 .59 1.17 .28 .61 .23 .247/.249 3/8-24 .52

89-AR2-64 3/8" .37 1.03 2.06 1.40 .59 1.17 .28 .61 .23 .247/.249 3/8-24 .49

89-AR3-64 1/2" .50 1.12 2.25 1.54 .59 1.17 .28 .61 .21 .247/.249 3/8-24 .58

89-AR4-64 3/4" .68 1.50 3.00 2.16 .70 1.39 .28 .84 .37 .247/.249 3/8-24 1.26

89-AR5-64 1" .87 1.68 3.37 2.28 .70 1.39 .28 .84 .37 .247/.249 3/8-24 1.62

89-AR6-64 1-1/4" 1.00 1.98 3.97 3.16 .98 1.95 .34 1.16 .54 .370/.372 5/8-18 3.22

89-AR7-64 1-1/2" 1.25 2.18 4.37 3.16 .98 1.95 .34 1.16 .58 .370/.372 5/8-18 4.06

89-AR8-64 2" 1.50 2.75 5.50 3.37 .98 1.95 .34 1.16 .55 .370/.372 5/8-18 6.18

89-AR9-64 2-1/2" 2.00 3.12 6.25 3.85 .98 1.95 .34 1.16 .54 .370/.372 5/8-18 13.06

89-AR0-64 3" 2.50 3.37 6.75 4.18 .98 1.95 .34 1.16 .54 .370/.372 5/8-18 17.06

CARBON STEEL STD. PORT BALL VALVE WITH ISO MOUNTING PAD

A-171/00


®399-100 SeriesAlloy-20 Ball Valve

Threaded, 1/4" to 1" 2000 psig WOG, 1-1/4" to 2" 1500 psig WOG. Cold Non-Shock.150 psig Saturated Steam. Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: SS, Style: 3.

FEATURES• Investment cast components • (-24) Certified to API standard 607, • Adjustable packing gland• RPTFE seats and stuffing box ring 4th Edition, Class 600 burn • Meets NACE MR-01-75• Mounting pad for easy actuator mounting • Blow-out-proof stem design

STANDARD MATERIAL LIST1. Lever and grip 304 SS w/vinyl 7. Gland nut 316 SS2. Stem packing RPTFE 8. Stem B473-N080203. Stem bearing RPTFE 9. Lever nut 304 SS4. Ball B463-2OCB-3 10. Body seal PTFE (1-1/4" to 2")5. Seat (2) RPTFE 11. Body A351-CN7M6. Retainer B473-N08020 (1/4" to 1")

A351-CN7M (1-1/4" to 2")

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/4" to 2"-03- 1-1/4" Stem Extension 1/4" to 2"-04- 2-1/4" Stem Extension 1/4" to 2"-07- Tee Handle 1/4" to 2"-08- 90º Reversed Stem 1/4" to 2"-14- Vented Ball (see page J-2) 1/4" to 2"-15- Round Handle 1/4" to 2"-16- Vertical Chain Lever 3/4" to 2"-18- Plain Yellow Grip 1/4" to 2"-19- Lock Plate 1/4" to 2"-21- UHMWPE Seats (Non-PTFE) 1/4" to 2"-24- Graphite Stem Packing 1/4" to 2"-27- Latch Lock Lever 1/4" to 2"-28- Mounting Pad Not Drilled 1/4" to 2"

& Tapped-30- CamLock Handle 1/4" to 2"-32- SS Tee Handle & Nut 1/4" to 2"-35- PTFE Trim 1/4" to 2"-40- Cyl-Loc 1/4" to 2"-45- Less Lever & Nut 1/4" to 2"-46- Latch Lock Lever - Lock Close Only 1/4" to 2"-47- SS Latch-Lock Oval Handle 1/4" to 1"-48- SS Oval Handle 1/4" to 2"-49- Assembled Dry 1/4" to 2"-50- 2-1/4" Locking Stem Extension 1/4" to 2"-56- Multifill Seats 1/4" to 2"-57- Cleaned For Gaseous Oxygen 1/4" to 2"-58- Horizontal Chain Lever 3/4" to 2"-60- Static Grounded Ball & Stem 1/4" to 2"-64- 250 Lb. Steam Trim 1/4" to 2"-P01- BSPP (Parallel) Thread Connection 1/4" to 2"-T01- BSPT (Tapered) Thread Connection 1/4" to 2"

NUMBER SIZE A B C D E F G Wt.399-101-01 1/4" .37 1.03 2.06 1.75 3.87 .50 1.12 .58399-102-01 3/8" .37 1.03 2.06 1.75 3.87 .50 1.12 .54399-103-01 1/2" .50 1.12 2.25 1.81 3.87 .50 1.12 .63399-104-01 3/4" .68 1.50 3.00 2.12 4.87 .87 1.37 1.27399-105-01 1" .87 1.68 3.37 2.25 4.87 .87 1.37 1.63399-106-01 1-1/4" 1.00 2.00 4.00 2.62 5.50 .93 1.50 3.06399-107-01 1-1/2" 1.25 2.18 4.37 2.87 8.00 .93 1.50 4.04399-108-01 2" 1.50 2.34 4.68 3.06 8.00 .93 1.50 6.05

ALLOY-20 BALL VALVE



(1-1/4" to 2")

1/00

SECTION B CONTENTSTHREE PIECE BALL VALVES

DESCRIPTION PAGE

82-100 Series, Threaded Full Port Bronze B-1

82-200 Series, Solder Full Port Bronze B-2

83R-100 Series, Actuator Ready Threaded Full Port Carbon Steel (New Item) B-3

83R-200 Series, Actuator Ready Socket Weld Full Port Carbon Steel (New Item) B-4

83R-700 Series, Actuator Ready Butt Weld Full Port Carbon Steel (New Item) B-5

85R-100 Series, Actuator Ready Threaded Stainless Steel (New Item) B-6

85R-200 Series, Actuator Ready Socket Weld Stainless Steel (New Item) B-7

86R-100 Series, Actuator Ready Threaded Full Port Stainless Steel (New Item) B-8

86R-200 Series, Actuator Ready Socket Weld Full Port Stainless Steel (New Item) B-9

86R-700 Series, Actuator Ready Butt Weld Full Port Stainless Steel (New Item) B-10

83-100 Series, Threaded Full Port Carbon Steel B-11

83-200 Series, Socket Weld Full Port Carbon Steel B-12

83-300 Series, Threaded High Pressure Carbon Steel B-13

83-400 Series, Socket Weld High Pressure Carbon Steel B-14

83-500 Series, Threaded Full Port High Pressure Carbon Steel B-15

83-600 Series, Socket Weld Full Port High Pressure Carbon Steel B-16

83-700 Series, Butt-Weld Full Port Carbon Steel B-17

85-100 Series, Threaded Stainless Steel B-18

85-200 Series, Socket Weld Stainless Steel B-19

86-100 Series, Threaded Full Port Stainless Steel B-20

86-200 Series, Socket Weld Full Port Stainless Steel B-21

86-500 Series, Threaded Full Port High Pressure Stainless Steel B-22

86-600 Series, Socket Weld Full Port High Pressure Stainless Steel B-23

86-700 Series, Butt-Weld Full Port Stainless Steel B-24

86-900 Series, Butt-Weld Full Port High Pressure Stainless Steel B-25

401-100 Series, Threaded Full Port Alloy-20 B-26

401-200 Series, Socket Weld Full Port Alloy-20 B-27


® 82-100 SeriesBronze 3-Piece Full Port Ball Valve


FEATURES• Full port configuration • Blow-out-proof stem design• RPTFE seats and seals • Adjustable packing gland• In-line repairable

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 10. Body bolt Steel, zinc plated2. Stem packing RPTFE 11. Hex nut Steel, zinc plated3. Stem bearing RPTFE 12. Body B584-C844004. Ball B16, chrome plated (except 3" & 4")5. Seat (2) RPTFE6. End cap (2) B16 (1/4" to 3/8")

B584-C84400 (1/2" to 4”)7. Gland nut B168. Stem B16 (except 3” & 4”)9. Lever nut Steel, zinc plated

VARIATIONS AVAILABLE:82-140 Series (316 SS Ball & Stem)82-150 Series (Original Balancing Stop)

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/4” to 4”-03- 1-1/4” Stem Extension 1/4” to 2”-04- 2-1/4” Stem Extension 1/4” to 2”-05- Plain Ball 1/4” to 4”-07- Tee Handle 1/4” to 2”-08- 90º Reversed Stem 1/4” to 4”-10- SS Lever & Nut 1/4” to 4”-14- Vented Ball (see page J-2) 1/4” to 4”-15- Round Handle 1/4” to 2”-16- Vertical Chain Lever 1/2” to 2”-18- Plain Yellow Grip 1/4” to 2”-19- Lock Plate 1/4” to 4”-20- Slot Vented Ball 1/4” to 4”-21- UHMWPE Seats 1/4” to 4”-23- Tank Flange 2” ONLY-24- Graphite Stem Packing 1/4” to 4”-27- Latch Lock Lever 1/2” to 2”-30- CamLock Handle 1/4” to 1-1/4”-32- SS Tee Handle & Nut 1/4” to 2”-35- PTFE Trim 1/4” to 4”-45- Less Lever & Nut 1/4” to 4”-46- Latch Lock Lever - Lock Close Only 1/2” to 2”-48- SS Oval Handle 1/4” to 2”-49- Assembled Dry 1/4” to 4”-50- 2-1/4” Locking Stem Extension 1/4” to 2”-57- Cleaned for Gaseous Oxygen 1/4” to 4”-58- Horizontal Chain Lever 1/2” to 2”-59- SS Body Trim 1/4” to 4”-60- Static Grounded Ball & Stem 1/4” to 4”-63- Threaded x Solder 3/8” to 4”-P01- BSPP (Parallel) Thread Connection 1/4” to 4”-T01- BSPT (Tapered) Thread Connection 1/4” to 4”

NUMBER SIZE A B C D E Wt.82-101-01 1/4" .43 1.28 2.56 1.81 3.87 1.0282-102-01 3/8" .50 1.28 2.56 1.81 3.87 1.0482-103-01 1/2" .62 1.40 2.81 1.93 4.87 1.5582-104-01 3/4" .81 1.71 3.43 2.18 4.87 2.2782-105-01 1" 1.00 1.93 3.87 2.62 5.50 3.2882-106-01 1-1/4" 1.25 2.37 4.75 2.87 5.50 5.6282-107-01 1-1/2" 1.50 2.62 5.25 3.37 8.00 8.0782-108-01 2" 2.00 3.01 6.03 3.68 8.00 14.4282-109-01 2-1/2" 2.50 3.62 7.25 5.14 9.75 26.6182-140-01 3" 3.00 4.00 8.00 6.77 18.00 42.2482-14A-01 4" 4.00 5.50 11.00 8.26 18.00 88.40

BRONZE 3-PIECE FULL PORT BALL VALVE

B-1


1/00


® 82-200 SeriesBronze 3-Piece Full Port Solder End Ball Valve

Solder End, 600 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35B, Type: II, Composition: BZ, Style: 1.Designed For Soft Solder or Brazed Installation.

FEATURES• Full port configuration • Blow-out-proof stem design• RPTFE seats and seals • Adjustable packing gland• In-line repairable

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 10. Body bolt Steel, zinc plated2. Stem packing RPTFE 11. Hex nut Steel, zinc plated3. Stem bearing RPTFE 12. Body B584-C844004. Ball B16, chrome plated (except 3” & 4”) 5. Seat (2) RPTFE6. End cap (2) B16 (3/8”)

B584-C84400 (1/2” to 4”)7. Gland nut B168. Stem B16 (except 3” & 4”) 9. Lever nut Steel, zinc plated


OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 3/8” to 4”-03- 1-1/4” Stem Extension 3/8” to 2”-04- 2-1/4” Stem Extension 3/8” to 2”-05- Plain Ball 3/8” to 4”-07- Tee Handle 3/8” to 2”-08- 90º Reversed Stem 3/8” to 4”-10- SS Lever & Nut 3/8” to 4”-14- Vented Ball (see page J-2) 3/8” to 4”-15- Round Handle 3/8” to 2”-16- Vertical Chain Lever 1/2” to 2”-18- Plain Yellow Grip 3/8” to 2”-19- Lock Plate 3/8” to 4”-20- Slot Vented Ball 3/8” to 4”-21- UHMWPE Seats 3/8” to 4”-23- Tank Flange 2” ONLY-24- Graphite Stem Packing 3/8” to 4”-27- Latch Lock Lever 1/2” to 2”-30- CamLock Handle 3/8” to 1-1/4”-32- SS Tee Handle & Nut 3/8” to 2”-35- PTFE Trim 3/8” to 4”-45- Less Lever & Nut 3/8” to 4”-46- Latch Lock Lever - Lock Close Only 1/2” to 2”-48- SS Oval Handle 1/4” to 2"-49- Assembled Dry 3/8” to 4”-50- 2-1/4” Locking Stem Extension 3/8” to 2”-57- Cleaned for Gaseous Oxygen 3/8” to 4”-58- Horizontal Chain Lever 1/2” to 2”-59- SS Body Trim 3/8” to 4”-60- Static Grounded Ball & Stem 3/8” to 4”

NUMBER SIZE A B C D E F G Wt.82-202-01 3/8” .50 1.28 2.56 1.81 3.87 .505 .37 .9982-203-01 1/2” .62 1.40 2.81 1.93 4.87 .630 .50 1.4682-204-01 3/4” .81 1.71 3.43 2.18 4.87 .880 .75 2.0782-205-01 1” 1.00 1.93 3.87 2.62 5.50 1.130 .90 3.0382-206-01 1-1/4” 1.25 2.37 4.75 2.87 5.50 1.380 .96 5.0282-207-01 1-1/2” 1.50 2.60 5.25 3.37 8.00 1.630 1.09 7.9182-208-01 2” 2.00 3.01 6.03 3.68 8.00 2.130 1.34 13.5082-209-01 2-1/2” 2.50 3.62 7.25 5.14 9.38 2.630 1.47 26.6182-240-01 3” 3.00 4.00 8.00 6.77 18.00 3.130 1.66 42.2482-24A-01 4” 4.00 5.50 11.00 8.26 18.00 4.130 2.16 88.40

BRONZE 3-PIECE FULL PORT BALL VALVE

B-2


1/00


®

B-3

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/4" to 2"-03- 1-1/4” Stem Extension 1/4" to 2"-04- 2-1/4” Stem Extension 1/4" to 2"-08- 90º Reversed Stem 1/4" to 2"-10- SS Lever & Nut 1/4" to 2"-14- Vented Ball 1/4" to 2"-18- Plain Yellow Grip 1/4" to 2"-21- UHMWPE Seats (Non-PTFE) 1/4" to 2"-24- Graphite Stem Packing 1/4" to 2"-27- Latch Lock Lever 1/4" to 2"-35- PTFE Trim 1/4" to 2"-39- SS Latch Lock Round Handle 1/4" to 2"-59- SS Body Trim 1/4" to 2"-60- Static Grounded Ball & Stem 1/4" to 2"-63- Threaded x Socket Weld 1/4" to 2"-P01- BSPP (Parallel) Thread Connection 1/4" to 2"-T01- BSPT (Tapered) Thread Connection 1/4" to 2"-AR- Less Handle & Stop-Add Belleville Washers1/4" to 2"-WB- With Lever & Belleville Washers 1/4" to 2"

J K L MNUMBER SIZE A B C D E F G H I (FLATS) (THRDS.)

UNF83R-101-01 1/4" .62 1.40 2.81 2.05 4.18 .59 1.17 .61 .28 .247/.249 3/8-24 .565 .5083R-102-01 3/8" .62 1.40 2.81 2.05 4.18 .59 1.17 .61 .28 .247/.249 3/8-24 .700 .5683R-103-01 1/2" .62 1.40 2.81 2.05 4.18 .59 1.17 .61 .28 .247/.249 3/8-24 .855 .4383R-104-01 3/4" .81 1.71 3.42 2.42 4.93 .70 1.39 .84 .28 .247/.249 3/8-24 1.065 .5683R-105-01 1" 1.00 1.92 3.85 2.54 4.93 .70 1.39 .84 .28 .247/.249 3/8-24 1.330 .6883R-106-01 1-1/4" 1.25 2.35 4.70 3.16 8.06 .98 1.95 1.16 .34 .370/.372 5/8-18 1.675 .8183R-107-01 1-1/2" 1.50 2.59 5.18 3.49 8.06 .98 1.95 1.16 .34 .370/.372 5/8-18 1.915 .8783R-108-01 2" 2.00 3.01 6.03 3.95 8.06 .98 1.95 1.16 .34 .370/.372 5/8-18 2.405 1.05

CARBON STEEL 3-PIECE FULL PORTBALL VALVE WITH ISO MOUNTING PAD


83R-100 SeriesCarbon Steel 3-Piece Full Port Ball ValveWith Actuator Ready ISO Mounting Pad

Full Port Threaded, 1000 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: CS, Style: 1.

FEATURES• Multi-piece packing set • Adjustable packing gland• ISO 5211 mounting pad • Investment cast components• Blow-out-proof stem design • RPTFE seats and seals• In-line repairable • Full port configuration

STANDARD MATERIAL LIST1. Stem A108-CS 7. Hex nut (4) Stl-gr. 8-zinc plt2. Jam nut Steel, zinc plate 8. Seat (2) RPTFE3. Low profile nut 316 SS 9. Ball A108-CS chrome plate4. Gland A108-CS 10. Body bolt (4) Stl-gr. 8-zinc plt5. Stem bearing RPTFE 11. Stem packing MPTFE6. End cap (2) A108-CS (1/4" to 1") 12. Body ASTM A216-WCB

A216-WCB (1-1/4" to 2") 13. Lock tab washer 304 SS14. Lever and grip Stl-zinc plt-w/vinyl

VARIATIONS AVAILABLE:• 83R-140 Series (316 SS Ball & Stem)• Meets NACE MR-01-75 (1-1/4" to 2")

NEW FOR

2000

1/00

B-4COPYRIGHT ©2000 CONBRACO IND., INC. – PRINTED IN U.S.A.

®



UNF83R-201-01 1/4" .62 1.40 2.81 2.05 4.18 .59 1.17 .61 .28 .247/.249 3/8-24 .565 .5083R-202-01 3/8" .62 1.40 2.81 2.05 4.18 .59 1.17 .61 .28 .247/.249 3/8-24 .700 .5683R-203-01 1/2" .62 1.40 2.81 2.05 4.18 .59 1.17 .61 .28 .247/.249 3/8-24 .855 .4383R-204-01 3/4" .81 1.71 3.42 2.42 4.93 .70 1.39 .84 .28 .247/.249 3/8-24 1.065 .5683R-205-01 1" 1.00 1.92 3.85 2.54 4.93 .70 1.39 .84 .28 .247/.249 3/8-24 1.330 .6883R-206-01 1-1/4" 1.25 2.35 4.70 3.16 8.06 .98 1.95 1.16 .34 .370/.372 5/8-18 1.675 .8183R-207-01 1-1/2" 1.50 2.59 5.18 3.49 8.06 .98 1.95 1.16 .34 .370/.372 5/8-18 1.915 .8783R-208-01 2" 2.00 3.01 6.03 3.95 8.06 .98 1.95 1.16 .34 .370/.372 5/8-18 2.405 1.05

CARBON STEEL 3-PIECE FULL PORT SOCKET WELDBALL VALVE WITH ISO MOUNTING PAD


83R-200 SeriesCarbon Steel 3-Piece Full Port Socket Weld

Ball Valve With Actuator Ready ISO Mounting PadSocket Weld, 1000 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: CS, Style: 1.





NEW FOR

2000

1/00


®

B-5


J KNUMBER SIZE A B C D E F G H I (FLATS) (THRDS.)

UNF83R-703-01 1/2" .62 1.40 2.81 2.05 4.18 .59 1.17 .61 .28 .247/.249 3/8-2483R-704-01 3/4" .81 1.71 3.42 2.42 4.93 .70 1.39 .84 .28 .247/.249 3/8-2483R-705-01 1" 1.00 1.92 3.85 2.54 4.93 .70 1.39 .84 .28 .247/.249 3/8-2483R-706-01 1-1/4" 1.25 2.35 4.70 3.16 8.06 .98 1.95 1.16 .34 .370/.372 5/8-1883R-707-01 1-1/2" 1.50 2.59 5.18 3.49 8.06 .98 1.95 1.16 .34 .370/.372 5/8-1883R-708-01 2" 2.00 3.01 6.03 3.95 8.06 .98 1.95 1.16 .34 .370/.372 5/8-18

CARBON STEEL 3-PIECE FULL PORT BUTT-WELDBALL VALVE WITH ISO MOUNTING PAD


83R-700 SeriesCarbon Steel 3-Piece Full Port Butt-Weld

Ball Valve With Actuator Ready ISO Mounting PadSchedule 40 Butt-Weld Ends, 1000 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: CS, Style: 1.





NEW FOR

2000

1/00


®

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 3/4" to 2"-03- 1-1/4” Stem Extension 3/4" to 2"-04- 2-1/4” Stem Extension 3/4" to 2"-08- 90º Reversed Stem 3/4" to 2"-14- Vented Ball 3/4" to 2"-18- Plain Yellow Grip 3/4" to 2"-21- UHMWPE Seats (Non-PTFE) 3/4" to 2"-24- Graphite Stem Packing 3/4" to 2"-27- Latch Lock Lever 3/4" to 2"-35- PTFE Trim 3/4" to 2"-39- SS Latch Lock Round Handle 3/4" to 2"-49- Assembled Dry 3/4" to 2"-57- Cleaned For Gaseous Oxygen 3/4" to 2"-60- Static Grounded Ball & Stem 3/4" to 2"-63- Threaded x Socket Weld 3/4" to 2"-P01- BSPP (Parallel) Thread Connection 3/4" to 2"-T01- BSPT (Tapered) Thread Connection 3/4" to 2"-AR- Less Handle & Stop-Add Belleville Washers3/4" to 2"-WB- With Lever & Belleville Washers 3/4" to 2"


85R-100 SeriesStainless Steel 3-Piece Ball Valve

With Actuator Ready ISO Mounting PadStd. Port Threaded, 1000 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: SS, Style: 1.


• Meets NACE MR01-75

STANDARD MATERIAL LIST1. Stem A276-316 8. Seat (2) RPTFE2. Jam nut SS 9. Ball 316 SS3. Low profile nut 316 SS 10. Body bolt (4) 18-8 SS4. Gland A276-316 11. Stem packing MPTFE5. Stem bearing RPTFE 12. Body ASTM A351-CF8M6. End cap (2) ASTM A351-CF8M 13. Lock tab washer 304 SS7. Hex nut (4) 18-8 SS 14. Lever and grip 304 SS w/vinyl

NEW FOR

2000


UNF85R-104-01 3/4" .62 1.40 2.81 2.05 4.18 .59 1.17 .61 .28 .247/.249 3/8-2485R-105-01 1" .81 1.71 3.42 2.42 4.93 .70 1.39 .84 .28 .247/.249 3/8-2485R-106-01 1-1/4" 1.00 1.92 3.85 2.54 4.93 .70 1.39 .84 .28 .247/.249 3/8-2485R-107-01 1-1/2" 1.25 2.35 4.70 3.16 8.06 .98 1.95 1.16 .34 .370/.372 5/8-1885R-108-01 2" 1.50 2.59 5.18 3.49 8.06 .98 1.95 1.16 .34 .370/.372 5/8-18

STAINLESS STEEL 3-PIECE STANDARD PORTBALL VALVE WITH ISO MOUNTING PAD

1/00


®

B-7



85R-200 SeriesStainless Steel 3-Piece Standard Port Socket WeldBall Valve With Actuator Ready ISO Mounting Pad

Socket Weld, 1000 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: SS, Style: 1.

FEATURES• Multi-piece packing set • Adjustable packing gland• ISO 5211 mounting pad • Investment cast components• Blow-out-proof stem design • RPTFE seats and seals• In-line repairable • Standard port configuration



NEW FOR

2000


UNF85R-204-01 3/4" .62 1.40 2.81 2.05 4.18 .59 1.17 .61 .28 .247/.249 3/8-24 1.065 .5685R-205-01 1" .81 1.71 3.42 2.42 4.93 .70 1.39 .84 .28 .247/.249 3/8-24 1.330 .6885R-206-01 1-1/4" 1.00 1.92 3.85 2.54 4.93 .70 1.39 .84 .28 .247/.249 3/8-24 1.675 .8185R-207-01 1-1/2" 1.25 2.35 4.70 3.16 8.06 .98 1.95 1.16 .34 .370/.372 5/8-18 1.915 .8785R-208-01 2" 1.50 2.59 5.18 3.49 8.06 .98 1.95 1.16 .34 .370/.372 5/8-18 2.406 1.06

STAINLESS STEEL 3-PIECE STANDARD PORT SOCKET WELDBALL VALVE WITH ISO MOUNTING PAD

1/00


®



UNF86R-101-01 1/4" .62 1.40 2.81 2.05 4.18 .59 1.17 .61 .28 .247/.249 3/8-24 .565 .5086R-102-01 3/8" .62 1.40 2.81 2.05 4.18 .59 1.17 .61 .28 .247/.249 3/8-24 .700 .5686R-103-01 1/2" .62 1.40 2.81 2.05 4.18 .59 1.17 .61 .28 .247/.249 3/8-24 .855 .4386R-104-01 3/4" .81 1.71 3.42 2.42 4.93 .70 1.39 .84 .28 .247/.249 3/8-24 1.065 .5686R-105-01 1" 1.00 1.92 3.85 2.54 4.93 .70 1.39 .84 .28 .247/.249 3/8-24 1.330 .6886R-106-01 1-1/4" 1.25 2.35 4.70 3.16 8.06 .98 1.95 1.16 .34 .370/.372 5/8-18 1.675 .8186R-107-01 1-1/2" 1.50 2.59 5.18 3.49 8.06 .98 1.95 1.16 .34 .370/.372 5/8-18 1.915 .8786R-108-01 2" 2.00 3.01 6.03 3.95 8.06 .98 1.95 1.16 .34 .370/.372 5/8-18 2.405 1.05

STAINLESS STEEL 3-PIECE FULL PORTBALL VALVE WITH ISO MOUNTING PAD


86R-100 SeriesStainless Steel 3-Piece Full Port Ball Valve

With Actuator Ready ISO Mounting PadFull Port Threaded, 1000 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: SS, Style: 1.




NEW FOR

2000

B-8 1/00


®



UNF86R-201-01 1/4" .62 1.40 2.81 2.05 4.18 .59 1.17 .61 .28 .247/.249 3/8-24 .565 .5086R-202-01 3/8" .62 1.40 2.81 2.05 4.18 .59 1.17 .61 .28 .247/.249 3/8-24 .700 .5686R-203-01 1/2" .62 1.40 2.81 2.05 4.18 .59 1.17 .61 .28 .247/.249 3/8-24 .855 .4386R-204-01 3/4" .81 1.71 3.42 2.42 4.93 .70 1.39 .84 .28 .247/.249 3/8-24 1.065 .5686R-205-01 1" 1.00 1.92 3.85 2.54 4.93 .70 1.39 .84 .28 .247/.249 3/8-24 1.330 .6886R-206-01 1-1/4" 1.25 2.35 4.70 3.16 8.06 .98 1.95 1.16 .34 .370/.372 5/8-18 1.675 .8186R-207-01 1-1/2" 1.50 2.59 5.18 3.49 8.06 .98 1.95 1.16 .34 .370/.372 5/8-18 1.915 .8786R-208-01 2" 2.00 3.01 6.03 3.95 8.06 .98 1.95 1.16 .34 .370/.372 5/8-18 2.405 1.05

STAINLESS STEEL 3-PIECE FULL PORT SOCKET WELDBALL VALVE WITH ISO MOUNTING PAD


86R-200 SeriesStainless Steel 3-Piece Full Port Socket Valve

Ball Valve With Actuator Ready ISO Mounting PadSocket Weld, 1000 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: SS, Style: 1.




NEW FOR

2000

1/00


®



86R-700 SeriesStainless Steel 3-Piece Full Port Butt-Weld

Ball Valve With Actuator Ready ISO Mounting PadSchedule 10 Butt-Weld Ends, 1000 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: SS, Style: 1.




NEW FOR

2000

STAINLESS STEEL 3-PIECE FULL PORT SOCKET WELDBALL VALVE WITH ISO MOUNTING PAD


UNF86R-703-01 1/2" .62 1.40 2.81 2.05 4.18 .59 1.17 .61 .28 .247/.249 3/8-2486R-704-01 3/4" .81 1.71 3.42 2.42 4.93 .70 1.39 .84 .28 .247/.249 3/8-2486R-705-01 1" 1.00 1.92 3.85 2.54 4.93 .70 1.39 .84 .28 .247/.249 3/8-2486R-706-01 1-1/4" 1.25 2.35 4.70 3.16 8.06 .98 1.95 1.16 .34 .370/.372 5/8-1886R-707-01 1-1/2" 1.50 2.59 5.18 3.49 8.06 .98 1.95 1.16 .34 .370/.372 5/8-1886R-708-01 2" 2.00 3.01 6.03 3.95 8.06 .98 1.95 1.16 .34 .370/.372 5/8-18

1/00


® 83-100 SeriesCarbon Steel 3-Piece Full Port Ball Valve

Threaded, 1000 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: CS, Style: 1.

FEATURES• Full port configuration • Blow-out-proof stem design• RPTFE seats and seals • Adjustable packing gland• In-line repairable • Cast components are investment castings• Actuator mounting pad (3/4” to 2”) • 1-1/4” to 2” meet NACE with SS trim• Nitride corrosion protection

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 7. Gland nut A108-CS2. Body bolt (4) Steel, SAE grade 8 zinc plated 8. Stem A108-CS3. Hex nut (4) Steel, SAE grade 8 zinc plated 9. Lever nut Steel, zinc plated4. Ball A108-CS chrome plated 10. Stem packing RPTFE5. Seat (2) RPTFE 11. Stem bearing RPTFE6. End cap (2) A108-CS (1/4” to 1”) 12. Body A216-WCB

A216-WCB (1-1/4” to 2”)VARIATIONS AVAILABLE:

83-140 Series (316 SS Ball & Stem)

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/4” to 2”-03- 1-1/4” Stem Extension 1/4” to 2”-04- 2-1/4” Stem Extension 1/4” to 2”-07- Tee Handle 1/4” to 2”-08- 90º Reversed Stem 1/4” to 2”-10- SS Lever & Nut 1/4” to 2”-14- Vented Ball (see page J-2) 1/4” to 2”-15- Round Handle 1/4” to 2”-16- Vertical Chain Lever 1/2” to 2”-18- Plain Yellow Grip 1/4” to 2”-19- Lock Plate 1/4” to 2”-21- UHMWPE Seats (Non-PTFE) 1/4” to 2”-23- Tank Flange 2” ONLY-24- Graphite Stem Packing 1/4” to 2”-27- Latch Lock Lever 1/2” to 2”-32- SS Tee Handle & Nut 1/4” to 2”-35- PTFE Trim 1/4” to 2”-45- Less Lever & Nut 1/4” to 2”-47- SS Latch-Lock Oval Handle 1/2” to 2”-48- SS Oval Handle 1/4” to 2”-58- Horizontal Chain Lever 1/2” to 2”-59- SS Body Trim 1/4” to 2”-60- Static Grounded Ball & Stem 1/4” to 2”-63- Female Threaded x Socket Weld 1/2” to 2”-P01- BSPP (Parallel) Thread Connection 1/4” to 2”-T01- BSPT (Tapered) Thread Connection 1/4” to 2”

B-11

NUMBER SIZE A B C D E F G Wt.83-101-01 1/4” .43 1.28 2.56 1.81 3.87 N/A N/A 1.0383-102-01 3/8” .50 1.28 2.56 1.81 3.87 N/A N/A .9983-103-01 1/2” .62 1.40 2.81 1.93 4.81 N/A N/A 1.40

83-104-01A 3/4” .81 1.71 3.43 2.18 4.81 1.25 1/4-20 1.9183-105-01A 1” 1.00 1.93 3.87 2.62 5.50 1.62 5/16-18 2.9883-106-01A 1-1/4” 1.25 2.37 4.75 2.87 5.50 1.62 5/16-18 5.0483-107-01A 1-1/2” 1.50 2.62 5.25 3.37 8.00 1.62 5/16-18 7.4683-108-01A 2” 2.00 3.01 6.03 3.68 8.00 1.62 5/16-18 12.83

CARBON STEEL 3-PIECE FULL PORT BALL VALVE


1/00


®

B-12

83-200 SeriesCarbon Steel 3-Piece Full Port Socket Weld Ball Valve

Socket Weld, 1000 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: CS, Style: 1.

FEATURES• Full port configuration • Blow-out-proof stem design• RPTFE seats and stuffing box ring • Adjustable packing gland• In-line repairable • Investment Cast Components• Actuator mounting pad (3/4” to 2”) • Meet NACE MR-01-75 with SS trim• Nitride corrosion protection

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 7. Gland nut A108-CS2. Body bolt (4) Steel, SAE grade 8 zinc plated 8. Stem A108-CS3. Hex nut (4) Steel, SAE grade 8 zinc plated 9. Lever nut Steel, zinc plated4. Ball A108-CS chrome plated 10. Stem packing RPTFE5. Seat (2) RPTFE 11. Stem bearing RPTFE6. End cap (2) A216-WCB 12. Body A216-WCB


OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/2” to 2”-03- 1-1/4” Stem Extension 1/2” to 2”-04- 2-1/4” Stem Extension 1/2” to 2”-07- Tee Handle 1/2” to 2”-08- 90º Reversed Stem 1/2” to 2”-10- SS Lever & Nut 1/2” to 2”-14- Vented Ball (see page J-2) 1/2” to 2”-15- Round Handle 1/2” to 2”-16- Vertical Chain Lever 1/2” to 2”-18- Plain Yellow Grip 1/2” to 2”-19- Lock Plate 1/2” to 2”-21- UHMWPE Seats (Non-PTFE) 1/2” to 2”-23- Tank Flange 2” ONLY-24- Graphite Stem Packing 1/2” to 2”-27- Latch Lock Lever 1/2” to 2”-32- SS Tee Handle & Nut 1/2” to 2”-35- PTFE Trim 1/2” to 2”-45- Less Lever & Nut 1/2” to 2”-47- SS Latch-Lock Oval Handle 1/2” to 2”-48- SS Oval Handle 1/2” to 2”-58- Horizontal Chain Lever 1/2” to 2”-59- SS Body Trim 1/2” to 2”-60- Static Grounded Ball & Stem 1/2” to 2”

NUMBER SIZE A B C D E F G H I Wt.83-203-01 1/2” .62 1.40 2.81 1.93 4.81 N/A N/A .855 .43 1.36

83-204-01A 3/4” .81 1.71 3.43 2.18 4.81 1.25 1/4-20 1.065 .56 1.8683-205-01A 1” 1.00 1.93 3.87 2.62 5.50 1.62 5/16-18 1.330 .68 2.8883-206-01A 1-1/4” 1.25 2.37 4.75 2.87 5.50 1.62 5/16-18 1.675 .81 4.9183-207-01A 1-1/2” 1.50 2.62 5.25 3.37 8.00 1.62 5/16-18 1.915 .87 7.2783-208-01A 2” 2.00 3.01 6.03 3.68 8.00 1.62 5/16-18 2.405 1.05 12.51

CARBON STEEL 3-PIECE FULL PORTSOCKET WELD BALL VALVE


1/00


®

B-13

83-300 SeriesCarbon Steel 3-Piece High Pressure Ball Valve

Standard Port, Threaded, 1500 psig WOG, Cold Non-Shock.150 psig Saturated Steam. Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: CS, Style: 1.

FEATURES• Nitride corrosion protection • Meets NACE MR-01-75 with SS trim• Adjustable packing gland • Investment Cast Components• In-line repairable • Actuator mounting pad (1” to 2”)• Blow-out-proof stem design • RPTFE seats and seals• (-29) certified to API 607 4TH ed. Class 600 burn

STANDARD MATERIAL LIST1. Lever and grip CS, zinc plated w/vinyl 8. Gland nut A108-CS2. Body bolt (4) Steel, SAE grade 8 zinc plated 9. Stem A108-CS3. Hex nut (4) Steel, SAE grade 8 zinc plated 10. Lever nut Steel, zinc plated4. Ball A108-CS chrome plated 11. Stem packing RPTFE5. Seat (2) RPTFE 12. Stem bearing RPTFE6. End cap (2) A216-WCB 13. Body A216-WCB7. Seat holder (2) A108-CS 14. Body seal (2) RPTFE


OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/2” to 2”-03- 1-1/4” Stem Extension 1/2” to 2”-04- 2-1/4” Stem Extension 1/2” to 2”-07- Tee Handle 1/2” to 2”-08- 90º Reversed Stem 1/2” to 2”-10- SS Lever & Nut 1/2” to 2”-14- Vented Ball (see page J-2) 1/2” to 2”-15- Round Handle 1/2” to 2”-16- Vertical Chain Lever 3/4” to 2”-18- Plain Yellow Grip 1/2” to 2”-27- Latch Lock Lever 1/2” to 2”-29- Firesafe 1/2” to 2”-32- SS Tee Handle & Nut 1/2” to 2”-45- Less Lever & Nut 1/2” to 2”-48- SS Oval Handle 1/2” to 2”-56- Multifill Seats 1/2” to 2”-58- Horizontal Chain Lever 3/4” to 2”-59- SS Body Trim 1/2” to 2”-60- Static Grounded Ball & Stem 1/2” to 2”-63- Threaded x Solder 1/2” to 2”-64- 250 Lb. Steam Trim 1/2” to 2”-P01- BSPP (Parallel) Thread Connection 1/2” to 2”-T01- BSPT (Tapered) Thread Connection 1/2” to 2”

NUMBER SIZE A B C D E F G Wt.83-303-01 1/2” .50 1.50 3.00 1.84 3.87 N/A N/A 1.2883-304-01 3/4” .62 1.87 3.74 2.00 4.87 N/A N/A 2.00

83-305-01A 1” .81 1.99 3.99 2.18 4.87 1.25 1/4-20 2.6983-306-01A 1-1/4” 1.00 2.31 4.62 2.60 5.50 1.62 5/16-18 3.9783-307-01A 1-1/2” 1.25 2.62 5.25 2.82 5.50 1.62 5/16-18 5.5083-308-01A 2” 1.50 2.74 5.48 3.37 8.00 1.62 5/16-18 8.05

CARBON STEEL 3-PIECEHIGH PRESSURE BALL VALVE


1/00


®

B-14

83-400 SeriesCarbon Steel 3-Piece High Pressure

Socket Weld Ball ValveStandard Port, Socket Weld, 1500 psig WOG, Cold Non-Shock.150 psig Saturated Steam. Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: CS, Style: 1.

FEATURES• Nitride corrosion protection • Meets NACE MR-01-75 with SS trim• Adjustable packing gland • Investment Cast Components• In-line repairable • Actuator mounting pad (1” to 2”)• Blow-out-proof stem design • RPTFE seats and seals• (-29) certified to API 607 4TH ed. Class 600 burn



OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/2” to 2”-03- 1-1/4” Stem Extension 1/2” to 2”-04- 2-1/4” Stem Extension 1/2” to 2”-07- Tee Handle 1/2” to 2”-08- 90º Reversed Stem 1/2” to 2”-10- SS Lever & Nut 1/2” to 2”-14- Vented Ball (see page J-2) 1/2” to 2”-15- Round Handle 1/2” to 2”-16- Vertical Chain Lever 3/4” to 2”-18- Plain Yellow Grip 1/2” to 2”-27- Latch Lock Lever 3/4” to 2”-29- Firesafe 1/2” to 2”-32- SS Tee Handle & Nut 1/2” to 2”-45- Less Lever & Nut 1/2” to 2”-48- SS Oval Handle 1/2” to 2”-56- Multifill Seats 1/2” to 2”-58- Horizontal Chain Lever 3/4” to 2”-59- SS Body Trim 1/2” to 2”-60- Static Grounded Ball & Stem 1/2” to 2”-64- 250 Lb. Steam Trim 1/2” to 2”

NUMBER SIZE A B C D E F G H I Wt.83-403-01 1/2” .50 1.50 3.00 1.84 3.87 N/A N/A .825 .43 1.2883-404-01 3/4” .62 1.87 3.74 2.00 4.87 N/A N/A 1.065 .56 2.00

83-405-01A 1” .81 1.99 3.99 2.18 4.87 1.25 1/4-20 1.330 .68 2.6983-406-01A 1-1/4” 1.00 2.31 4.62 2.60 5.50 1.62 5/16-18 1.675 .81 3.9783-407-01A 1-1/2” 1.25 2.62 5.25 2.82 5.50 1.62 5/16-18 1.915 .87 5.5083-408-01A 2” 1.50 2.74 5.48 3.37 8.00 1.62 5/16-18 5.406 1.06 8.05

CARBON STEEL 3-PIECE HIGH PRESSURESOCKET WELD BALL VALVE


1/00

NUMBER SIZE A B C D E F G Wt.83-501-01 1/4” .43 1.50 3.00 1.93 3.87 N/A N/A 1.2183-502-01 3/8” .50 1.50 3.00 1.93 3.87 N/A N/A 1.2283-503-01 1/2” .62 1.69 3.38 2.00 4.81 N/A N/A 1.90

83-504-01A 3/4” .81 1.93 3.87 2.18 4.81 1.25 1/4-20 2.5683-505-01A 1” 1.00 2.25 4.50 2.62 5.50 1.62 5/16-18 3.7883-506-01A 1-1/4” 1.25 2.43 4.87 2.87 5.50 1.62 5/16-18 5.2483-507-01A 1-1/2” 1.50 2.62 5.25 3.35 8.00 1.62 5/16-18 7.6783-508-01A 2” 2.00 3.12 6.25 3.75 8.00 1.62 5/16-18 15.60


®

B-15

83-500 SeriesCarbon Steel 3-Piece High Pressure Full Port

Ball ValveThreaded, 1500 psig WOG. Cold Non-Shock. 150 psig Saturated Steam. Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: CS, Style: 1.

FEATURES• Nitride corrosion protection • (-29) Certified to API standard 607, • Investment Cast Components• Adjustable packing gland 4th Edition, Class 600 burn • Actuator mounting pad (3/4” to 2”)• In-line repairable • Meets NACE MR-01-75 with SS trim • RPTFE seats and seals• Blow-out-proof stem design



OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/4” to 2”-03- 1-1/4” Stem Extension 1/4” to 2”-04- 2-1/4” Stem Extension 1/4” to 2”-07- Tee Handle 1/4” to 2”-08- 90º Reversed Stem 1/4” to 2”-10- SS Lever & Nut 1/4” to 2”-14- Vented Ball (see page J-2) 1/4” to 2”-16- Vertical Chain Lever 1/2” to 2”-18- Plain Yellow Grip 1/4” to 2”-27- Latch Lock Lever 1/4” to 2”-29- Firesafe 1/4” to 2”-32- SS Tee Handle & Nut 1/4” to 2”-38- PEEK Seats & Bearing 1/4” to 2”-45- Less Lever & Nut 1/4” to 2”-47- SS Latch-Lock Oval Handle 1/4” to 2”-48- SS Oval Handle 1/4” to 2”-56- Multifill Seats 1/4” to 2”-58- Horizontal Chain Lever 1/2” to 2”-59- SS Body Trim 1/4” to 2”-60- Static Grounded Ball & Stem 1/4” to 2”-63- Female Threaded x Socket Weld 1/4” to 2”-64- 250 Lb. Steam Trim 1/4” to 2”-P01- BSPP (Parallel) Thread Connection 1/4” to 2”-T01- BSPT (Tapered) Thread Connection 1/4” to 2”

CARBON STEEL 3-PIECE HIGH PRESSUREFULL PORT BALL VALVE


1/00

COPYRIGHT ©1997 CONBRACO IND., INC. – PRINTED IN U.S.A.B-16

® 83-600 SeriesCarbon Steel 3-Piece High Pressure Full Port

Socket Weld Ball ValveSocket Weld, 1500 psig WOG, Cold Non-Shock. 150 psig Saturated Steam. Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: CS, Style: 1.

FEATURES• Nitride corrosion protection • (-29) Certified to API standard 607, • Investment Cast Components• Adjustable packing gland 4th Edition, Class 600 burn • Actuator mounting pad (3/4” to 2”)• In-line repairable • Meets NACE MR-01-75 with SS trim • RPTFE seats and seals• Blow-out-proof stem design



OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/2” to 2”-03- 1-1/4” Stem Extension 1/2” to 2”-04- 2-1/4” Stem Extension 1/2” to 2”-07- Tee Handle 1/2” to 2”-08- 90º Reversed Stem 1/2” to 2”-10- SS Lever & Nut 1/2” to 2”-14- Vented Ball (see page J-2) 1/2” to 2”-15- Round Handle 1/2” to 2”-16- Vertical Chain Lever 1/2” to 2”-18- Plain Yellow Grip 1/2” to 2”-27- Latch Lock Lever 1/2” to 2”-29- Firesafe 1/2” to 2”-32- SS Tee Handle & Nut 1/2” to 2”-38- PEEK Seats & Bearing 1/2” to 2”-45- Less Lever & Nut 1/2” to 2”-47- SS Latch-Lock Oval Handle 1/2” to 2”-48- SS Oval Handle 1/4” to 2”-56- Multifill Seats 1/2” to 2”-58- Horizontal Chain Lever 1/2” to 2”-59- SS Body Trim 1/2” to 2”-60- Static Grounded Ball & Stem 1/2” to 2”-64- 250 Lb. Steam Trim 1/2” to 2”


83-604-01A 3/4” .81 1.93 3.87 2.18 4.81 1.25 1/4-20 1.065 .56 2.5683-605-01A 1” 1.00 2.25 4.50 2.62 5.50 1.62 5/16-18 1.330 .68 3.7883-606-01A 1-1/4” 1.25 2.43 4.87 2.87 5.50 1.62 5/16-18 1.675 .81 5.2483-607-01A 1-1/2” 1.50 2.62 5.25 3.35 8.00 1.62 5/16-18 1.915 .87 7.6783-608-01A 2” 2.00 3.12 6.25 3.75 8.00 1.62 5/16-18 2.406 1.06 15.60

CARBON STEEL 3-PIECE HIGH PRESSURE FULL PORTSOCKET WELD BALL VALVE


1/00


® 83-700 SeriesCarbon Steel 3-Piece Full Port Butt-Weld Ball Valve

Schedule 40 Butt-Weld Ends. 1000 psig WOG. Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: CS, Style: 1.

FEATURES• Full port configuration • Meets NACE MR-01-75 with SS trim• Adjustable packing • Investment Cast Components• In-line repairable • Actuator mounting pad (3/4” to 2”)• Blow-out-proof stem design • RPTFE seats and seals• Nitride corrosion protection

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 7. Gland nut A108-CS2. Body bolt (4) Steel, SAE grade 8 zinc plated 8. Stem A108-CS3. Hex nut (4) Steel, SAE grade 8 zinc plated 9. Lever nut Steel, zinc plated4. Ball A108-CS chrome plated 10. Stem packing RPTFE5. Seat (2) RPTFE 11. Stem bearing RPTFE6. End Cap (2) A216-WCB 12. Body CS


NUMBER SIZE A B C D E F G Wt.83-703-01 1/2” .62 1.40 2.81 1.93 4.81 N/A N/A 1.36

83-704-01A 3/4” .81 1.71 3.43 2.18 4.81 1.25 1/4-20 1.8683-705-01A 1” 1.00 1.93 3.87 2.62 5.50 1.62 5/16-18 2.8883-707-01A 1-1/2” 1.50 2.62 5.25 3.37 8.00 1.62 5/16-18 7.2783-708-01A 2” 2.00 3.01 6.03 3.68 8.00 1.62 5/16-18 12.51

CARBON STEEL 3-PIECE FULL PORTBUTT-WELD VALVE

B-17

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/2” to 2”-03- 1-1/4” Stem Extension 1/2” to 2”-04- 2-1/4” Stem Extension 1/2” to 2”-07- Tee Handle 1/2” to 2”-08- 90º Reversed Stem 1/2” to 2”-10- SS Lever & Nut 1/2” to 2”-14- Vented Ball (see page J-2) 1/2” to 2”-15- Round Handle 1/2” to 2”-16- Vertical Chain Lever 1/2” to 2”-18- Plain Yellow Grip 1/2” to 2”-19- Lock Plate 1/2” to 2”-21- UHMWPE Seats (Non-PTFE) 1/2” to 2”-23- Tank Flange 2” ONLY-24- Graphite Stem Packing 1/2” to 2”-27- Latch Lock Lever 1/2” to 2”-32- SS Tee Handle & Nut 1/2” to 2”-35- PTFE Trim 1/2” to 2”-45- Less Lever & Nut 1/2” to 2”-47- SS Latch-Lock Oval Handle 1/2” to 2”-48- SS Oval Handle 1/2” to 2”-58- Horizontal Chain Lever 1/2” to 2”-59- SS Body Trim 1/2” to 2”-60- Static Grounded Ball & Stem 1/2” to 2”


1/00


® 85-100 SeriesStainless Steel 3-Piece Ball Valve

Standard Port Threaded, 1000 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: SS, Style: 1.

FEATURES• Meets NACE MR-01-75 • Investment cast components• Blow-out-proof stem design • Actuator mounting pad (1” to 2”)• In-line repairable • RPTFE seats and seals• Adjustable packing gland

STANDARD MATERIAL LIST1. Lever and grip 304 SS w/vinyl 7. Gland nut A276-3162. Stem packing RPTFE 8. Stem A276-3163. Stem bearing RPTFE 9. Lever nut 18-8 SS4. Ball A276-316 10. Body bolt (4) 18-8 SS5. Seat (2) RPTFE 11. Hex nut (4) 18-8 SS6. End cap (2) A351-CF3M 12. Body A351-CF8M

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/4” to 2”-03- 1-1/4” Stem Extension 1/4” to 2”-04- 2-1/4” Stem Extension 1/4” to 2”-07- Tee Handle 1/4” to 2”-08- 90º Reversed Stem 1/4” to 2”-14- Vented Ball (see page J-2) 1/4” to 2”-15- Round Handle 1/4” to 2”-16- Vertical Chain Lever 3/4” to 2”-18- Plain Yellow Grip 1/4” to 2”-24- Graphite Stem Packing 1/4” to 2”-27- Latch Lock Lever 1/2” to 2”-30- CamLock Handle 1/4” to 3/4”-32- SS Tee Handle & Nut 1/4” to 2”-35- PTFE Trim 1/4” to 2”-45- Less Lever & Nut 1/4” to 2”-47- SS Latch-Lock Oval Handle 1/2” to 2”-48- SS Oval Handle 1/4” to 2”-49- Assembled Dry 1/4” to 2”-50- 2-1/4” Locking Stem Extension 1/4” to 3/4”-57- Cleaned For Gaseous Oxygen 1/4” to 2”-58- Horizontal Chain Lever 3/4” to 2”-60- Static Grounded Ball & Stem 1/4” to 2”-61- Grounded Ball & Stem and 1/4” to 2”

Assembled Dry-63- Threaded x Socket Weld 1/2” to 2”-P01- BSPP (Parallel) Thread Connection 1/4” to 2”-T01- BSPT (Tapered) Thread Connection 1/4” to 2”

STAINLESS STEEL 3-PIECE BALL VALVE

B-18

NUMBER SIZE A B C D E F G Wt.85-101-01 1/4” .43 1.28 2.56 1.81 3.87 N/A N/A 1.0285-102-01 3/8” .50 1.28 2.56 1.81 3.87 N/A N/A .9885-103-01 1/2” .50 1.28 2.56 1.81 3.87 N/A N/A .9785-104-01 3/4” .62 1.38 2.75 1.93 4.87 N/A N/A 1.35

85-105-01A 1” .81 1.70 3.40 2.18 4.87 1.25 1/4-20 1.9685-106-01A 1-1/4” 1.00 1.95 3.91 2.60 5.50 1.62 5/16-18 2.8385-107-01A 1-1/2” 1.25 2.22 4.45 2.82 5.50 1.62 5/16-18 4.6385-108-01A 2” 1.50 2.51 5.02 3.37 8.00 1.62 5/16-18 7.12


1/00


® 85-200 SeriesStainless Steel 3-Piece Socket Weld Ball Valve

Standard Port Socket Weld, 1000 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: SS, Style: 1.

FEATURES• Meets NACE MR-01-75 • Investment cast components• Blow-out-proof stem design • Actuator mounting pad (1” to 2”)• In-line repairable • RPTFE seats and seals• Adjustable packing gland


OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/2” to 2”-03- 1-1/4” Stem Extension 1/2” to 2”-04- 2-1/4” Stem Extension 1/2” to 2”-07- Tee Handle 1/2” to 2”-08- 90º Reversed Stem 1/2” to 2”-10- SS Lever & Nut 1/2” to 2”-14- Vented Ball (see page J-2) 1/2” to 2”-15- Round Handle 1/2” to 2”-16- Vertical Chain Lever 3/4” to 2”-18- Plain Yellow Grip 1/2” to 2”-24- Graphite Stem Packing 1/2” to 2”-27- Latch Lock Lever 1/2” to 2”-30- CamLock Handle 1/2” to 3/4”-32- SS Tee Handle & Nut 1/2” to 2”-35- PTFE Trim 1/2” to 2”-45- Less Lever & Nut 1/2” to 2”-47- SS Latch-Lock Oval Handle 1/2” to 2”-48- SS Oval Handle 1/2” to 2”-49- Assembled Dry 1/2” to 2”-57- Cleaned For Gaseous Oxygen 1/2” to 2”-58- Horizontal Chain Lever 3/4” to 2”-60- Static Grounded Ball & Stem 1/2” to 2”

B-19

NUMBER SIZE A B C D E F G H I Wt.85-203-01 1/2” .50 1.28 2.56 1.81 3.87 N/A N/A .855 .43 .9785-204-01 3/4” .62 1.38 2.75 1.93 4.87 N/A N/A 1.065 .56 1.35

85-205-01A 1” .81 1.70 3.40 2.18 4.87 1.25 1/4-20 1.330 .68 1.9685-206-01A 1-1/4” 1.00 1.95 3.91 2.60 5.50 1.62 5/16-18 1.675 .81 2.8385-207-01A 1-1/2” 1.25 2.22 4.45 2.82 5.50 1.62 5/16-18 1.915 .87 4.6385-208-01A 2” 1.50 2.51 5.02 3.37 8.00 1.62 5/16-18 2.406 1.06 7.12

STAINLESS STEEL 3-PIECE SOCKET WELD BALL VALVE


1/00


®

B-20

86-100 SeriesStainless Steel 3-Piece Full Port Ball Valve

Full Port Threaded, 1000 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: SS, Style: 1.

FEATURES• AAR Approved • Investment cast components• Blow-out-proof stem design • Actuator mounting pad (3/4” to 2”)• In-line repairable • RPTFE seats and seals• Adjustable packing gland • Full port configuration• Meets NACE MR-01-75


OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/4” to 3”-03- 1-1/4” Stem Extension 1/4” to 3”-04- 2-1/4” Stem Extension 1/4” to 3”-07- Tee Handle 1/4” to 3”-08- 90º Reversed Stem 1/4” to 3”-14- Vented Ball (see page J-2) 1/4” to 3”-15- Round Handle 1/4” to 3”-16- Vertical Chain Lever 1/2” to 3”-18- Plain Yellow Grip 1/4” to 3”-19- Lock Plate 1/4” to 3”-21- UHMWPE Seats (Non-PTFE) 1/4” to 3”-23- Tank Flange 2” ONLY-24- Graphite Stem Packing 1/4” to 3”-27- Latch Lock Lever 1/2” to 3”-30- CamLock Handle 1/2” ONLY-32- SS Tee Handle & Nut 1/4” to 3”-35- PTFE Trim 1/4” to 3”-45- Less Lever & Nut 1/4” to 3”-48- SS Oval Handle 1/4” to 2”-49- Assembled Dry 1/4” to 3”-57- Cleaned For Gaseous Oxygen 1/4” to 3”-58- Horizontal Chain Lever 1/2” to 3”-60- Static Grounded Ball & Stem 1/4” to 3”-63- Threaded x Socket Weld 3/8” to 3”-P01- BSPP (Parallel) Thread Connection 1/4” to 3”-T01- BSPT (Tapered) Thread Connection 1/4” to 3”

STAINLESS STEEL 3-PIECE FULL PORT BALL VALVENUMBER SIZE A B C D E F G Wt.86-101-01 1/4” .43 1.28 2.56 1.81 3.87 N/A N/A 1.0286-102-01 3/8” .50 1.28 2.56 1.81 3.87 N/A N/A .9886-103-01 1/2” .62 1.40 2.81 1.93 4.81 N/A N/A 1.35

86-104-01A 3/4” .81 1.71 3.43 2.18 4.81 1.25 1/4-20 1.8986-105-01A 1” 1.00 1.93 3.87 2.62 5.50 1.62 5/16-18 2.9586-106-01A 1-1/4” 1.25 2.37 4.75 2.87 5.50 1.62 5/16-18 5.0086-107-01A 1-1/2” 1.50 2.62 5.25 3.37 8.00 1.62 5/16-18 7.3686-108-01A 2” 2.00 3.01 6.03 3.68 8.00 1.62 5/16-18 12.7386-100-01A 3” 3.00 4.00 8.00 5.62 9.75 N/A N/A 41.15


1/00


®

B-21

86-200 SeriesStainless Steel 3-Piece Full Port Socket Weld Ball Valve


FEATURES• AAR Approved • Investment cast components• Blow-out-proof stem design • Actuator mounting pad (3/4” to 2”)• In-line repairable • RPTFE seats and seals• Adjustable packing gland • Full port configuration• Meets NACE MR-01-75


OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 3/8” to 3”-03- 1-1/4” Stem Extension 3/8” to 2”-04- 2-1/4” Stem Extension 3/8” to 2”-07- Tee Handle 3/8” to 2”-08- 90º Reversed Stem 3/8” to 3”-14- Vented Ball (see page J-2) 3/8” to 3”-15- Round Handle 3/8” to 2”-16- Vertical Chain Lever 1/2” to 2”-18- Plain Yellow Grip 3/8” to 2”-19- Lock Plate 3/8” to 2”-21- UHMWPE Seats (Non-PTFE) 3/8” to 3”-23- Tank Flange 2” ONLY-24- Graphite Stem Packing 3/8” to 3”-27- Latch Lock Lever 3/8” to 2”-30- CamLock Handle 1/2” ONLY-32- SS Tee Handle & Nut 3/8” to 2”-35- PTFE Trim 3/8” to 3”-45- Less Lever & Nut 3/8” to 3”-48- SS Oval Handle 3/8” to 2”-49- Assembled Dry 3/8” to 3”-57- Cleaned For Gaseous Oxygen 3/8” to 3”-58- Horizontal Chain Lever 1/2” to 3”-60- Static Grounded Ball & Stem 3/8” to 3”

NUMBER SIZE A B C D E F G H I Wt.86-202-01 3/8” .50 1.28 2.56 1.81 3.37 N/A N/A .690 .56 .9886-203-01 1/2” .62 1.40 2.81 1.93 4.81 N/A N/A .855 .43 1.33

86-204-01A 3/4” .81 1.71 3.43 2.18 4.81 1.25 1/4-20 1.065 .56 1.8686-205-01A 1” 1.00 1.93 3.87 2.62 5.50 1.62 5/16-18 1.330 .68 2.7686-206-01A 1-1/4” 1.25 2.37 4.75 2.87 5.50 1.62 5/16-18 1.675 .81 4.8786-207-01A 1-1/2” 1.50 2.62 5.25 3.37 8.00 1.62 5/16-18 1.915 .87 7.1886-208-01A 2” 2.00 3.01 6.03 3.68 8.00 1.62 5/16-18 2.406 1.06 12.4286-200-01A 3” 3.00 4.00 8.00 5.62 9.75 N/A N/A 3.540 1.37 40.36

STAINLESS STEEL 3-PIECE FULL PORT SOCKETWELD BALL VALVE


1/00


®

B-22

86-500 SeriesStainless Steel 3-Piece High Pressure Full Port Ball Valve

Threaded, 1500 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: SS, Style: 1.

FEATURES• Adjustable packing gland • (-29) Certified to API standard 607, • Investment Cast Components• In-line repairable 4th Edition, Class 600 burn • Actuator mounting pad (3/4” to 2”)• Blow-out-proof stem design • Meets NACE MR-01-75 • RPTFE seats and seals

STANDARD MATERIAL LIST1. Lever and grip 304 SS w/vinyl 8. Gland nut A276-3162. Stem packing RPTFE 9. Stem A276-3163. Stem bearing RPTFE 10. Lever nut 304 SS4. Ball A276-316 11. Body bolt (4) 18-8 SS5. Seat (2) RPTFE 12. Hex nut (4) 18-8 SS6. End cap (2) A351-CF3M 13. Body A351-CF8M7. Seat holder (2) A276-316 14. Body seal (2) RPTFE

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/4” to 2”-03- 1-1/4” Stem Extension 1/4” to 2”-04- 2-1/4” Stem Extension 1/4” to 2”-07- Tee Handle 1/4” to 2”-08- 90º Reversed Stem 1/4” to 2”-14- Vented Ball (see page J-2) 1/4” to 2”-15- Round Handle 1/4” to 2”-16- Vertical Chain Lever 1/2” to 2”-18- Plain Yellow Grip 1/4” to 2”-27- Latch Lock Lever 1/4” to 2”-29- Firesafe 1/4” to 2”-32- SS Tee Handle & Nut 1/4” to 2”-38- PEEK Seats and Bearing 1/4” to 2”-45- Less Lever & Nut 1/4” to 2”-47- SS Latch-Lock Oval Handle 1/4” to 2”-48- SS Oval Handle 1/4” to 2”-49- Assembled Dry 1/4” to 2”-56- Multifull Seats 1/4” to 2”-57- Cleaned for Gaseous Oxygen 1/4” to 2”-58- Horizontal Chain Lever 1/2” to 2”-60- Static Grounded Ball & Stem 1/4” to 2”-63- Threaded x Socket Weld 1/2” to 2”-64- 250 Lb. Steam Trim 1/4” to 2”-66- NPT x Butt Weld 1/2” to 2”-P01- BSPP (Parallel) Thread Connection 1/4” to 2”-T01- BSPT (Tapered) Thread Connection 1/4” to 2”

STAINLESS STEEL 3-PIECE HIGH PRESSUREFULL PORT BALL VALVE

NUMBER SIZE A B C D E F G Wt.86-501-01 1/4” .43 1.50 3.00 1.93 3.87 N/A N/A 1.2386-502-01 3/8” .50 1.50 3.00 1.93 3.87 N/A N/A 1.1886-503-01 1/2” .62 1.69 3.38 2.00 4.81 N/A N/A 1.62

86-504-01A 3/4” .81 1.93 3.87 2.18 4.81 1.25 1/4-20 2.2786-505-01A 1” 1.00 2.25 4.50 2.62 5.50 1.62 5/16-18 3.5486-506-01A 1-1/4” 1.25 2.43 4.87 2.87 5.50 1.62 5/16-18 6.0086-507-01A 1-1/2” 1.50 2.62 5.25 3.35 8.00 1.62 5/16-18 8.8486-508-01A 2” 2.00 3.12 6.25 3.75 8.00 1.62 5/16-18 15.28


1/00


®

B-23

86-600 SeriesStainless Steel 3-Piece High Pressure Full Port Socket

Weld Ball ValveSocket Weld, 1500 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: SS, Style: 1.

FEATURES• Adjustable packing gland • Meets NACE MR-01-75• In-line repairable • Investment Cast Components• Blow-out-proof stem design • Actuator mounting pad (3/4” to 2”)• (-29) certified to API 607 4TH ed. Class 600 burn • RPTFE seats and seals

STANDARD MATERIAL LIST1. Lever and grip 304 SS w/vinyl 8. Gland nut A276-3162. Stem packing RPTFE 9. Stem A276-3163. Stem bearing RPTFE 10. Lever nut 18-8 SS4. Ball A276-316 11. Body bolt (4) 18-8 SS5. Seat (2) RPTFE 12. Hex nut (4) 18-8 SS6. End cap (2) A351-CF3M 13. Body A351-CF8M7. Seat holder (2) A276-316 14. Body seal (2) RPTFE

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/2” to 2”-03- 1-1/4” Stem Extension 1/2” to 2”-04- 2-1/4” Stem Extension 1/2” to 2”-07- Tee Handle 1/2” to 2”-08- 90º Reversed Stem 1/2” to 2”-14- Vented Ball (see page J-2) 1/2” to 2”-15- Round Handle 1/2” to 2”-16- Vertical Chain Lever 1/2” to 2”-18- Plain Yellow Grip 1/2” to 2”-27- Latch Lock Lever 1/2” to 2”-29- Firesafe 1/2” to 2”-32- SS Tee Handle & Nut 1/2” to 2”-38- PEEK Seats and Bearing 1/2” to 2”-45- Less Lever & Nut 1/2” to 2”-48- SS Oval Handle 1/2” to 2”-49- Assembled Dry 1/2” to 2”-56- Multifill Seats 1/2” to 2”-57- Cleaned for Gaseous Oxygen 1/2” to 2”-58- Horizontal Chain Lever 1/2” to 2”-60- Static Grounded Ball & Stem 1/2” to 2”-64- 250 Lb. Steam Trim 1/2” to 2”

STAINLESS STEEL 3-PIECE HIGH PRESSUREFULL PORT SOCKET WELD BALL VALVE


86-604-01A 3/4” .81 1.93 3.87 2.18 4.81 1.25 1/4-20 1.065 .56 2.2486-605-01A 1” 1.00 2.25 4.50 2.62 5.50 1.62 5/16-18 1.330 .68 3.3286-606-01A 1-1/4” 1.25 2.43 4.87 2.87 5.50 1.62 5/16-18 1.675 .81 5.8586-607-01A 1-1/2” 1.50 2.62 5.25 3.35 8.00 1.62 5/16-18 1.915 .87 8.6286-608-01A 2” 2.00 3.12 6.25 3.75 8.00 1.62 5/16-18 2.406 1.06 15.60

G Tapping


1/00


®

B-24

86-700 SeriesStainless Steel 3-Piece Full Port Butt-Weld Ball Valve

Schedule 10 Butt-Weld Ends, 1000 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: SS, Style: 1.

FEATURES• AAR Approved • Investment cast components• Adjustable packing gland • Actuator mounting pad (3/4” to 2”)• In-line repairable • RPTFE seats and seals• Blow-out-proof stem design • Full port configuration• Meets NACE MR-01-75


STAINLESS STEEL 3-PIECE FULL PORTBUTT-WELD BALL VALVE

NUMBER SIZE A B C D E F G Wt.86-703-01 1/2” .62 1.40 2.81 1.93 4.81 N/A N/A 1.87

86-704-01A 3/4” .81 1.71 3.43 2.18 4.81 1.25 1/4-20 1.9886-705-01A 1” 1.00 1.93 3.87 2.62 5.50 1.62 5/16-18 2.9086-707-01A 1-1/2” 1.50 2.62 5.25 3.37 8.00 1.62 5/16-18 7.0086-708-01A 2” 2.00 3.01 6.03 3.68 8.00 1.62 5/16-18 13.08

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/2” to 2”-03- 1-1/4” Stem Extension 1/2” to 2”-04- 2-1/4” Stem Extension 1/2” to 2”-07- Tee Handle 1/2” to 2”-08- 90º Reversed Stem 1/2” to 2”-14- Vented Ball (see page J-2) 1/2” to 2”-15- Round Handle 1/2” to 2”-16- Vertical Chain Lever 1/2” to 2”-18- Plain Yellow Grip 1/2” to 2”-21- UHMWPE Seats (Non-PTFE) 1/2” to 2”-23- Tank Flange 2” ONLY-24- Graphite Stem Packing 1/2” to 2”-27- Latch Lock Lever 1/2” to 2”-30- CamLock Handle 1/2”ONLY-32- SS Tee Handle & Nut 1/2” to 2”-35- PTFE Trim 1/2” to 2”-45- Less Lever & Nut 1/2” to 2”-48- SS Oval Handle 1/2” to 2”-49- Assembled Dry 1/2” to 2”-57- Cleaned For Gaseous Oxygen 1/2” to 2”-58- Horizontal Chain Lever 1/2” to 2”-60- Static Grounded Ball & Stem 1/2” to 2”


1/00

® 86-900 SeriesStainless Steel 3-Piece High Pressure

Full Port Butt-Weld Ball ValveSchedule 10 Butt-Weld, 1500 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: SS, Style: 1.

FEATURES• Adjustable packing gland • Meets NACE MR-01-75-97• In-line repairable • Investment Cast Components• Blow-out-proof stem design • Actuator mounting pad (3/4” to 2”)• (-29) Certified to API standard 607, 4th Edition, Class 600 burn • RPTFE seats and seals

STANDARD MATERIAL LIST1. Lever and grip 304 SS w/vinyl 8. Gland nut A276-3162. Stem packing RPTFE 9. Stem A276-3163. Stem bearing RPTFE 10. Lever nut 304 SS4. Ball A276-316 11. Body bolt (4) 18-8 SS5. Seat (2) RPTFE 12. Hex nut (4) 18-8 SS6. End cap (2) A351-CF3M 13. Body A351-CF8M7. Seat Holder (2) A276-316 14. Body seal (2) RPTFE

STAINLESS STEEL 3-PIECE HIGH PRESSURE FULL PORTBUTT-WELD BALL VALVE

NUMBER SIZE A B C D E F G Wt.86-903-01 1/2” .62 1.69 3.38 2.00 4.81 N/A N/A 1.6086-904-01A 3/4” .81 1.93 3.87 2.18 4.81 1.25 1/4-20 2.2486-905-01A 1” 1.00 2.25 4.50 2.62 5.50 1.62 5/16-18 3.3286-907-01A 1-1/2” 1.50 2.62 5.25 3.35 8.00 1.62 5/16-18 8.6286-908-01A 2” 2.00 3.11 6.22 3.75 8.00 1.62 5/16-18 15.60

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/2” to 2”-03- 1-1/4” Stem Extension 1/2” to 2”-04- 2-1/4” Stem Extension 1/2” to 2”-07- Tee Handle 1/2” to 2”-08- 90º Reversed Stem 1/2” to 2”-14- Vented Ball (see page J-2) 1/2” to 2”-15- Round Handle 1/2” to 2”-16- Vertical Chain Lever 1/2” to 2”-18- Plain Yellow Grip 1/2” to 2”-27- Latch Lock Lever 1/2” to 2”-29- Firesafe 1/2” to 2”-32- SS Tee Handle & Nut 1/2” to 2”-35- PTFE Trim 1/2” to 2”-38- PEEK Seats and Bearing 1/2” to 2”-45- Less Lever & Nut 1/2” to 2”-47- SS Latch-Lock Oval Handle 1/2” to 2”-48- SS Oval Handle 1/2” to 2”-49- Assembled Dry 1/2” to 2”-57- Cleaned For Gaseous Oxygen 1/2” to 2”-58- Horizontal Chain Lever 1/2” to 2”-60- Static Grounded Ball & Stem 1/2” to 2”-64- 250 lb. Steam Trim 1/2” to 2”


COPYRIGHT ©1997 CONBRACO IND., INC. – PRINTED IN U.S.A. B-251/001/00

® 401-100 SeriesAlloy-20 3-Piece Full Port Ball Valve

Threaded, 1000 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: SS, Style: 1.

FEATURES• Blow-out-proof stem design • Investment cast components• In-line repairable • Actuator mounting pad (3/4” to 2”)• Adjustable packing gland • RPTFE seats and seals• Meets NACE MR-01-75 • Full port configuration

STANDARD MATERIAL LIST1. Lever and grip 304 SS w/vinyl 7. Gland nut A276-3162. Stem packing RPTFE 8. Stem B473-N080203. Stem bearing RPTFE 9. Lever nut 18-8 SS4. Ball B473-N08020 10. Body bolt (4) 18-8 SS5. Seat (2) RPTFE 11. Hex nut (4) 18-8 SS6. End cap (2) A351-CN7M 12. Body A351-CN7M

ALLOY-20 3-PIECE FULL PORT BALL VALVENUMBER SIZE A B C D E F G Wt.401-103-01 1/2” .62 1.40 2.81 1.93 4.81 N/A N/A 1.40401-104-01 3/4” .81 1.71 3.43 2.18 4.81 1.25 1/4-20 1.94401-105-01 1” 1.00 1.93 3.87 2.62 5.50 1.62 5/16-18 3.00401-107-01 1-1/2” 1.50 2.62 5.25 3.37 8.00 1.62 5/16-18 7.41401-108-01 2” 2.00 3.01 6.03 3.68 8.00 1.62 5/16-18 12.78

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/2” to 2”-03- 1-1/4” Stem Extension 1/2” to 2”-04- 2-1/4” Stem Extension 1/2” to 2”-07- Tee Handle 1/2” to 2”-08- 90º Reversed Stem 1/2” to 2”-14- Vented Ball (see page J-2) 1/2” to 2”-15- Round Handle 1/2” to 2”-16- Vertical Chain Lever 1/2” to 2”-18- Plain Yellow Grip 1/2” to 2”-19- Lock Plate 1/2” to 2”-21- UHMWPE Seats (Non-PTFE) 1/2” to 2”-24- Graphite Stem Packing 1/2” to 2”-27- Latch Lock Lever 1/2” to 2”-30- CamLock Handle 1/2”ONLY-32- SS Tee Handle & Nut 1/2” to 2”-35- PTFE Trim 1/2” to 2”-45- Less Lever & Nut 1/2” to 2”-48- SS Oval Handle 1/2” to 2”-49- Assembled Dry 1/2” to 2”-57- Cleaned For Gaseous Oxygen 1/2” to 2”-58- Horizontal Chain Lever 1/2” to 2”-60- Static Grounded Ball & Stem 1/2” to 2”-63- Female Threaded x Socket Weld 1/2” to 2”-P01- BSPP (Parallel) Thread Connection 1/2” to 2”-T01- BSPT (Tapered) Thread Connection 1/2” to 2”


COPYRIGHT ©1997 CONBRACO IND., INC. – PRINTED IN U.S.A.B-26 1/00

COPYRIGHT ©1997 CONBRACO IND., INC. – PRINTED IN U.S.A. B-27

® 401-200 SeriesAlloy-20 3-Piece Full Port Socket Weld Ball Valve


FEATURES• Blow-out-proof stem design • Investment cast components• In-line repairable • Actuator mounting pad (3/4” to 2”)• Adjustable packing gland • RPTFE seats and seals• Meets NACE MR-01-75 • Full port configuration

STANDARD MATERIAL LIST1. Lever and grip 304 SS w/vinyl 7. Gland nut A276-3162. Stem packing RPTFE 8. Stem B473-N080203. Stem bearing RPTFE 9. Lever nut 18-8 SS4. Ball B473-N08020 10. Body bolt (4) 18-8 SS5. Seat (2) RPTFE 11. Hex nut (4) 18-8 SS6. End cap (2) A351-CN7M 12. Body A351-CN7M

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/2” to 2”-03- 1-1/4” Stem Extension 1/2” to 2”-04- 2-1/4” Stem Extension 1/2” to 2”-07- Tee Handle 1/2” to 2”-08- 90º Reversed Stem 1/2” to 2”-14- Vented Ball (see page J-2) 1/2” to 2”-15- Round Handle 1/2” to 2”-16- Vertical Chain Lever 1/2” to 2”-18- Plain Yellow Grip 1/2” to 2”-19- Lock Plate 1/2” to 2”-21- UHMWPE Seats (Non-PTFE) 1/2” to 2”-24- Graphite Stem Packing 1/2” to 2”-27- Latch Lock Lever 1/2” to 2”-30- CamLock Handle 1/2” ONLY-32- SS Tee Handle & Nut 1/2” to 2”-35- PTFE Trim 1/2” to 2”-45- Less Lever & Nut 1/2” to 2”-48- SS Oval Handle 1/2” to 2”-49- Assembled Dry 1/2” to 2”-57- Cleaned For Gaseous Oxygen 1/2” to 2”-58- Horizontal Chain Lever 1/2” to 2”-60- Static Grounded Ball & Stem 1/2” to 2”

ALLOY-20 3-PIECE FULL PORT SOCKETWELD BALL VALVE

NUMBER SIZE A B C D E F G H I Wt.401-203-01 1/2” .62 1.40 2.81 1.93 4.81 N/A N/A .855 .43 1.38401-204-01 3/4” .81 1.71 3.43 2.18 4.81 1.25 1/4-20 1.065 .56 1.92401-205-01 1” 1.00 1.93 3.87 2.62 5.50 1.62 5/16-18 1.330 .68 2.98401-207-01 1-1/2” 1.50 2.62 5.25 3.37 8.00 1.62 5/16-18 1.915 .87 7.39401-208-01 2” 2.00 3.01 6.03 3.68 8.00 1.62 5/16-18 2.406 1.06 12.76


1/00

SECTION E CONTENTSTHREE WAY VALVES

DESCRIPTION PAGE

70-600 Series, Threaded Bronze E-1

70-900 Series, Solder Bronze E-2

76-600 Series, Threaded Stainless Steel E-3

3-Way Valve Application E-4

E-1COPYRIGHT ©1997 CONBRACO IND., INC. – PRINTED IN U.S.A.

® 70-600 Series3-Way Diversion Bronze Ball Valve

Threaded, 400 psig WOG, Cold Non-Shock.


STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 7. Gland nut B162. Stem packing RPTFE 8. Stem B163. Stem bearing RPTFE 9. Lever nut Steel, zinc plated4. Ball B16, chrome plated 10. Body seal (1-1/2" to 2") PTFE5. Seat (2) RPTFE 11. Body B584-C844006. Retainer B16 (1/2" to 1")

B584-C84400 (1-1/4" to 2")

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/4" to 2"-03- 1-1/4" Stem Extension 1/4" to 2"-04- 2-1/4" Stem Extension 1/4" to 2"-05- Plain Ball 1/4" to 2"-10- SS Lever & Nut 1/4" to 2"-17- Rough Chrome Plating 1/4" to 2"-21- UHMWPE Seats (Non-PTFE) 1/4" to 2"-24- Graphite Stem Packing 1/4" to 2"-27- Latch Lock Lever 1/4" to 2"-35- PTFE Trim 1/4" to 2"-49- Assembled Dry 1/4" to 2"-50- 2-1/4” Locking Stem Extension 1/4" to 2"-56- Multifill Seats 1/4" to 2"-57- Cleaned for Gaseous Oxygen 1/4" to 2"-60- Static Grounded Ball & Stem 1/4" to 2"-P01- BSPP (Parallel) Thread Connection 1/4" to 2"-T01- BSPT (Tapered) Thread Connection 1/4" to 2"

NUMBER SIZE A B C D E F G H I Wt.70-601-01 1/4" .37 1.12 2.32 1.8 3.88 1.18 .875 1.37 10-24 .9170-602-01 3/8" .37 1.12 2.32 1.8 3.88 1.18 .875 1.37 10-24 .8870-603-01 1/2" .50 1.09 2.25 1.75 3.87 1.18 .87 1.37 10-24 .7670-604-01 3/4" .68 1.50 3.00 2.12 4.87 1.62 .87 1.37 10-24 1.6570-605-01 1" .81 1.59 3.18 2.25 4.87 1.71 .87 1.37 10-24 2.1570-606-01 1-1/4" 1.00 1.97 3.95 2.69 5.50 2.01 .93 1.50 1/4-20 3.8570-607-01 1-1/2" 1.25 2.21 4.40 2.87 5.50 2.38 .94 1.50 1/4-20 5.2270-608-01 2" 1.50 2.34 4.69 3.00 5.50 2.50 .94 1.50 1/4-20 6.20

3-WAY DIVERSION BRONZE BALL VALVE


NOTE: Open port pressure must exceed Closed port pressure.

FLOW PATTERN

For Pressure/Temperature Ratings,Referto Page N-10, Graph No. 4

1/00

E-2 COPYRIGHT ©1997 CONBRACO IND., INC. – PRINTED IN U.S.A.

® 70-900 Series3-Way Diversion Bronze Solder End Ball Valve

Solder, 400 psig WOG, Cold Non-Shock.


STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 6. Retainer B16 2. Stem packing RPTFE 7. Gland nut B163. Stem bearing RPTFE 8. Stem B164. Ball B16, chrome plated 9. Lever nut Steel, zinc plated5. Seat (2) RPTFE 10. Body B584-C84400

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/2" to 1"-03- 1-1/4" Stem Extension 1/2" to 1"-04- 2-1/4" Stem Extension 1/2" to 1"-05- Plain Ball 1/2" to 1"-10- SS Lever & Nut 1/2" to 1"-17- Rough Chrome Plating 1/2" to 1"-21- UHMWPE Seats (Non-PTFE) 1/2" to 1"-24- Graphite Stem Packing 1/2" to 1"-27- Latch Lock Lever 1/2" to 1"-35- PTFE Trim 1/2" to 1"-49- Assembled Dry 1/2" to 1"-50- 2-1/4” Locking Stem Extension 1/2" to 1"-56- Multifill Seats 1/2" to 1"-57- Cleaned for Gaseous Oxygen 1/2" to 1"-60- Static Grounded Ball & Stem 1/2" to 1"


FLOW PATTERN


The 70-900 is designed to be soft soldered into lines withoutdisassembly. This allows a tested valve to be installed withoutdisturbing the seats and seals in any way. Solderingtemperature not to exceed 500ºF.

NUMBER SIZE A B C D E F G H Wt.70-903-01 1/2" .50 1.44 2.87 1.75 3.87 1.34 .628 .50 .7670-904-01 3/4" .68 1.94 3.87 2.12 4.87 1.69 .878 .90 1.6570-905-01 1" .81 2.19 4.42 2.25 4.87 1.87 1.129 .90 2.15

3-WAY DIVERSION BRONZE BALL VALVEFor Pressure/Temperature Ratings,


E-3COPYRIGHT ©1997 CONBRACO IND., INC. – PRINTED IN U.S.A.

® 76-600 Series3-Way Diversion Stainless Steel Ball Valve


FEATURES• RPTFE seats and stuffing box ring • Blow-out-proof stem design• Meets NACE MR-01-75 • Adjustable packing gland

• Investment cast body

STANDARD MATERIAL LIST1. Lever and grip 304 SS w/vinyl 7. Gland nut A276-316 2. Stem packing RPTFE 8. Stem A276-316 3. Stem bearing RPTFE 9. Lever nut 18-8 SS4. Ball A276-316 10. Body seal (1-1/2" to 2") PTFE5. Seat (2) RPTFE 11. Body A351-CF8M6. Retainer A276-316 (1/2" to 1")

A351-CF8M (1-1/2" to 2")

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/4" to 2"-03- 1-1/4" Stem Extension 1/4" to 2"-04- 2-1/4" Stem Extension 1/4" to 2"-21- UHMWPE Seats (Non-PTFE) 1/4" to 2"-24- Graphite Stem Packing 1/4" to 2"-27- Latch Lock Lever 1/4" to 2"-35- PTFE Trim 1/4" to 2"-49- Assembled Dry 1/4" to 2"-50- 2-1/4” Locking Stem Extension 1/4" to 2"-56- Multifill Seats 1/4" to 2"-57- Cleaned for Gaseous Oxygen 1/4" to 2"-60- Static Grounded Ball & Stem 1/4" to 2"-P01- BSPP (Parallel) Thread Connection 1/4" to 2"-T01- BSPT (Tapered) Thread Connection 1/4" to 2"


FLOW PATTERN

3-WAY DIVERSION STAINLESS STEEL BALL VALVE

NUMBER SIZE A B C D E F G H I Wt.76-601-01 1/4" .37 1.12 2.32 1.8 3.88 1.18 .875 1.37 10-24 .776-602-01 3/8" .37 1.12 2.32 1.8 3.88 1.18 .875 1.37 10-24 .6876-603-01 1/2" .50 1.12 2.32 1.81 3.87 1.18 .87 1.37 10-24 .7576-604-01 3/4" .68 1.50 3.00 2.12 4.87 1.50 .87 1.37 10-24 1.4576-605-01 1" .81 1.60 3.21 2.25 4.87 1.68 .87 1.37 10-24 1.8676-607-01 1-1/2" 1.25 2.21 4.40 2.87 5.50 2.40 .94 1.50 1/4-20 4.6776-608-01 2" 1.50 2.75 5.45 3.06 5.50 2.81 .94 1.50 1/4-20 7.02


1/00

E-4 COPYRIGHT ©1997 CONBRACO IND., INC. – PRINTED IN U.S.A.

3-Way ValvesMixing Vs. Diverting

Illustrated to the right are the three normal operating positionsfor a three-way valve. Apollo’s three-way valve has only two(2) seats as illustrated and as such has limitations for use inboth diverter and mixing valve applications. As can be seenfrom this illustration, there is no off position for port “C”. Ports“A” and “B” cannot be off at the same time.

Apollo’s Three-Way Valve as aMixing Valve

When ports “A” and “B” are the inlets, and port “C” is theoutlet, the valve becomes a mixing valve. With minorvariations in position 2 the percentage of components at “A”and “B” can be varied to the outlet “C”. This has beensuccessfully applied to hydronic systems.

It may not be possible to isolate the ports from one another inany position. If the valve is in position 1, and the pressure atport “B” is significantly higher than port “A”, the ball may beforced off the seat allowing mixing from all ports. Whether ornot this is a problem depends on the application and itssensitivity to unwanted mixing.

Apollo’s Three-Way Valve as aDiverter Valve

When port “C” is the inlet, and ports “A” and “B” are theoutlets, the valve is a diverter valve. With port “C” as the inlet,flow is diverted to either port “A” (position 1) or “B” (position 3).In position 2, inlet flow from “C” is split to “A” and “B”.

Just as described above, it may not be possible to isolate any one port from the other two. That condition is mostlikely to occur in mixing applications. That is why the valve tends to be promoted as a diverter valve rather thana mixing valve.

®

SECTION F CONTENTSUNION END VALVES

DESCRIPTION PAGE

70-300 Series, Threaded Bronze, Single Union End F-1

70-400 Series, Solder Bronze, Single Union End F-2

73-300 Series, Threaded Carbon Steel, Double Union End (UL Listed) F-3

73-400 Series, Socket Weld Carbon Steel, Double Union End (UL Listed) F-4

76-300 Series, Threaded Stainless Steel, Double Union End F-5

76-400 Series, Socket Weld Stainless Steel, Double Union End F-6

F-1COPYRIGHT ©1997 CONBRACO IND., INC. – PRINTED IN U.S.A.

® 70-300 SeriesSingle Union End Bronze Ball Valve

Threaded, Single Union End, 600 psig WOG, Cold Non-Shock.150 psig Saturated Steam, Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: BZ, Style: 3.

FEATURES• Chromium plated ball • Blow-out-proof stem design• RPTFE seats and stuffing box ring • Adjustable packing gland• Fluorocarbon O-Ring sealed single union requires only light torque to seal

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 8. Stem B162. Stem packing RPTFE 9. Lever nut Steel, zinc plated3. Stem bearing RPTFE 10. Body seal (1-1/4" to 2") PTFE4. Ball B16, chrome plated 11. Body B584-C844005. Seat (2) RPTFE 12. Tailpiece B16 or B584-C844006. Retainer B16 (1/4" to 1-1/2") 13. Union nut B16 or B584-C84400

B584-C84400 (2") 14. Union seal Fluorocarbon7. Gland nut B16

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/4" to 2"-03- 1-1/4" Stem Extension 1/4" to 2"-04- 2-1/4" Stem Extension 1/4" to 2"-05- Plain Ball 1/4" to 2"-07- Tee Handle 1/4" to 2"-08- 90º Reversed Stem 1/4" to 2"-10- SS Lever & Nut 1/4" to 2"-14- Vented Ball(see page J-2) 1/4" to 2"-15- Round Handle 1/4" to 2"-16- Vertical Chain Lever 3/4" to 2"-17- Rough Chrome Plating 1/4" to 2"-18- Plain Yellow Grip 1/4" to 2"-20- Slot Vented Ball 1/4" to 2"-21- UHMWPE Seats (Non-PTFE) 1/4" to 2"-24- Graphite Stem Packing 1/4" to 2"-27- Latch Lock Lever 1/4" to 2"-30- CamLock Handle 1/4" to 2"-32- SS Tee Handle & Nut 1/4" to 2"-35- PTFE Trim 1/4" to 2"-45- Less Lever & Nut 1/4" to 2"-46- Latch Lock Lever - Lock Close Only 1/4" to 2"-48- SS Oval Handle 1/4" to 2"-49- Assembled Dry 1/4" to 2"-50- 2-1/4” Locking Stem Extension 1/4" to 2"-56- Multifill Seats 1/4" to 2"-57- Cleaned for Gaseous Oxygen 1/4" to 2"-58- Horizontal Chain Lever 3/4" to 2"-60- Static Grounded Ball & Stem 1/4" to 2"-63- Threaded x Solder Tailpiece 3/8" to 2"


BRONZE UNION ENDBALL VALVE



F-2 COPYRIGHT ©1997 CONBRACO IND., INC. – PRINTED IN U.S.A.

® 70-400 SeriesSingle Union End Solder Bronze Ball Valve

Solder Ends, Single Union End, 600 psig WOG, Cold Non-Shock.150 psig Saturated Steam, Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: BZ, Style: 3.

FEATURES• Chromium plated ball • Blow-out-proof stem design• RPTFE seats and stuffing box ring • Adjustable packing gland• Fluorocarbon O-Ring sealed single union requires only light torque to seal

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 8. Stem B162. Stem packing RPTFE 9. Lever nut Steel, zinc plated3. Stem bearing RPTFE 10. Body seal (1-1/4" to 2") PTFE4. Ball B16, chrome plated 11. Body B584-C844005. Seat (2) RPTFE 12. Tailpiece B16 or B584-C844006. Retainer B16 or B584-C84400 13. Union nut B16 or B584-C844007. Gland nut B16 14. Union seal Fluorocarbon

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES

-02- Static Grounded 3/8" to 2"-03- 1-1/4" Stem Extension 3/8" to 2"-04- 2-1/4" Stem Extension 3/8" to 2"-05- Plain Ball 3/8" to 2"-07- Tee Handle 3/8" to 2"-08- 90º Reversed Stem 3/8" to 2"-10- SS Lever & Nut 3/8" to 2"-14- Vented Ball(see page J-2) 3/8" to 2"-15- Round Handle 3/8" to 2"-16- Vertical Chain Lever 3/4" to 2"-17- Rough Chrome Plating 3/8" to 2"-18- Plain Yellow Grip 3/8" to 2"-20- Slot Vented Ball 3/8" to 2"-21- UHMWPE Seats (Non-PTFE) 3/8" to 2"-24- Graphite Stem Packing 3/8" to 2"-27- Latch Lock Lever 3/8" to 2"-30- CamLock Handle 3/8" to 2"-32- SS Tee Handle & Nut 3/8" to 2"-35- PTFE Trim 3/8" to 2"-45- Less Lever & Nut 3/8" to 2"-46- Latch Lock Lever - Lock Close Only 3/8" to 2"-48- SS Oval Handle 3/8" to 2"-49- Assembled Dry 3/8" to 2"-50- 2-1/4” Locking Stem Extension 3/8" to 2"-56- Multifill Seats 3/8" to 2"-57- Cleaned for Gaseous Oxygen 3/8" to 2"-58- Horizontal Chain Lever 3/4" to 2"-60- Static Grounded Ball & Stem 3/8" to 2"-63- Threaded x Solder Tailpiece 3/8" to 2"


NUMBER SIZE A B C D E F G Wt.70-402-01 3/8" .37 1.81 3.09 1.75 3.87 .503 .37 .8570-403-01 1/2" .50 2.00 3.43 1.75 3.87 .628 .50 1.0270-404-01 3/4" .68 2.62 4.56 2.06 4.78 .878 .75 1.9370-405-01 1" .87 2.81 5.06 2.25 4.78 1.129 .90 2.4270-406-01 1-1/4" 1.00 2.87 5.18 2.62 5.50 1.378 .96 4.1170-407-01 1-1/2" 1.25 2.92 5.53 3.10 8.00 1.629 1.09 5.4470-408-01 2" 1.50 3.50 6.75 3.24 8.00 2.129 1.34 7.77

SINGLE UNION ENDSOLDER BRONZE BALL VALVE

The 70-400 is designed to be soft soldered intolines without disassembly. This allows atested valve to be installed withoutdisturbing the seats and seals in any way.Soldering temperature not to exceed 500ºF.


F-3COPYRIGHT ©1997 CONBRACO IND., INC. – PRINTED IN U.S.A.

® 73-300 SeriesCarbon Steel Double Union End Ball Valve

Threaded, 3000 psig WOG, Cold Non-Shock, 150 psig Saturated Steam.Vacuum Service to 29 inches Hg. Federal Specification: WW-V-35C, Type II, Composition: CS, Style: 1

FEATURES• Heavy duty quarter turn lever • Blow-out-proof stem design• RPTFE seats and seals • Adjustable packing gland• Steel barstock design • Chromium plated ball• Easy installation and maintenance • Nitride corrosion protection

UL LISTINGS @ 250 PSIG MAX• Guide YRPV: Gas shutoff valve for use with natural and manufactured gases.• Guide YSDT: LP gas shutoff valve.• Guide YRBX: Flammable liquid shutoff valve.

Note: Listings apply ONLY to the standard -01 valves.

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 9. Lever nut Steel, zinc plated2. Stem packing RPTFE 10. Body A108-CS3. Stem bearing RPTFE 11. Seat (2) RPTFE4. Ball A108-CS chrome plated 12. Union nut (2) A108-CS5. Tailpiece (2) A108-CS 13. Seat holder A108-CS6. Retainer A108-CS 14. Union seal (2) RPTFE7. Gland nut A108-CS 15. Retainer seal RPTFE8. Stem A108-CS chrome plated

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/4" to 2"-07- Tee Handle 1/4" to 1-1/2"-08- 90º Reversed Stem 1/4" to 2"-10- SS Lever & Nut 1/4" to 2"-14- Vented Ball(see page J-2) 1/4" to 2"-15- Round Handle 1/4" to 1"-18- Plain Yellow Grip 1/4" to 2"-19- Lock Plate 1/4" to 2"-22- Fluorocarbon Union Seals 1/4" to 2"-29- Firesafe 1/4" to 2"-45- Less Lever & Nut 1/4" to 2"-60- Static Grounded Ball & Stem 1/4" to 2"-63- Threaded x Socket Weld 1/2" to 2"-64- 250 Lb. Steam Trim 1/4" to 2"-P01- BSPP (Parallel) Thread Connection 1/4" to 2"-T01- BSPT (Tapered) Thread Connection 1/4" to 2"

NUMBER SIZE A B C D E Wt.73-301-01 1/4" .43 2.50 5.00 2.50 5.62 3.5173-302-01 3/8" .57 2.50 5.00 2.50 5.62 3.4573-303-01 1/2" .62 2.50 5.00 2.50 5.62 3.3573-304-01 3/4" .81 2.71 5.31 2.62 5.62 4.4873-305-01 1" 1.00 2.96 6.06 3.12 6.62 7.0473-306-01 1-1/4" 1.25 2.87 6.12 3.43 8.00 9.9673-307-01 1-1/2" 1.50 3.46 7.12 3.56 8.00 14.8373-308-01 2" 1.75 3.75 7.50 4.18 9.00 20.50

CARBON STEEL DOUBLE UNION ENDBALL VALVE


UL®

LISTED



® 73-400 SeriesCarbon Steel Double Union End Socket Weld Ball Valve

Socket Weld End, 3000 psig WOG, Cold Non-Shock, 150 psig Saturated Steam.Vacuum Service to 29 inches Hg. Federal Specification: WW-V-35C, Type II, Composition: CS, Style: 1


UL LISTINGS @ 250 PSIG MAX• Guide YRPV: Gas shutoff valve for use with natural and manufactured gases.• Guide YSDT: LP gas shutoff valve.• Guide YRBX: Flammable liquid shutoff valve.


STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 9. Lever nut Steel, zinc plated2. Stem packing RPTFE 10. Body A108-CS3. Stem bearing RPTFE 11. Tail piece (2) A108-10184. Ball A108-CS chrome plated 12. Union nut (2) A108-CS5. Seat (2) RPTFE 13. Seat holder A108-CS6. Retainer A108-CS 14. Union seal (2) RPTFE7. Gland nut A108-CS 15. Retainer seal RPTFE8. Stem A108-CS chrome plated

UL®

LISTED

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/2" to 2"-07- Tee Handle 1/2" to 1-1/2"-08- 90º Reversed Stem 1/2" to 2"-10- SS Lever & Nut 1/2" to 2"-14- Vented Ball(see page J-2) 1/2" to 2"-15- Round Handle 1/2" to 1"-18- Plain Yellow Grip 1/2" to 2"-19- Lock Plate 1/2" to 2"-22- Fluorocarbon Union Seals 1/2" to 2"-29- Firesafe 1/2" to 2"-45- Less Lever & Nut 1/2" to 2"-60- Static Grounded Ball & Stem 1/2" to 2"-64- 250 Lb. Steam Trim 1/2" to 2"


NUMBER SIZE A B C D E F G Wt.73-403-01 1/2" .62 2.50 5.00 2.50 5.62 .43 .855 3.3573-404-01 3/4" .81 2.71 5.31 2.62 5.62 .56 1.065 4.4873-405-01 1" 1.00 2.93 6.06 3.12 6.62 .68 1.330 7.0473-406-01 1-1/4" 1.25 2.87 6.12 3.43 8.00 .81 1.675 9.9673-407-01 1-1/2" 1.50 3.46 7.12 3.56 8.00 .81 1.915 14.8373-408-01 2" 1.75 3.75 7.50 4.18 9.00 1.06 2.406 20.50

CARBON STEEL DOUBLE UNION ENDSOCKET WELD BALL VALVE


STAINLESS STEEL DOUBLEUNION END BALL VALVE


® 76-300 SeriesDouble Union End Stainless Steel Ball Valve

Threaded, 1/2" to 1" 2000 psig WOG, 1-1/4" to 2" 1500 psig WOG. Cold Non-Shock.150 psig Saturated Steam, Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: SS, Style: 1.

FEATURES• Heavy duty quarter turn handles • Blow-out-proof stem design• RPTFE seats and seals • Adjustable packing gland

STANDARD MATERIAL LIST1. Lever and grip 304 SS w/vinyl 9. Lever nut 18-8 SS2. Stem packing RPTFE 10. Body A351-CF8M3. Stem bearing RPTFE 11. Tailpiece (2) A276-3164. Ball A276-316 12. Union nut (2) Nitride A108-CS5. Seat (2) RPTFE 13. Seat holder A276-3166. Retainer A276-316 14. Union seal (2) RPTFE7. Gland nut A276-316 15. Retainer seal RPTFE8. Stem A276-316

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/2" to 2"-03- 1-1/4" Stem Extension 1/2" to 1-1/2"-04- 2-1/4" Stem Extension 1/2" to 1-1/2"-07- Tee Handle 1/2" to 1-1/2"-08- 90º Reversed Stem 1/2" to 2"-14- Vented Ball(see page J-2) 1/2" to 2"-15- Round Handle 1/2" to 1-1/2"-18- Plain Yellow Grip 1/2" to 2"-22- Fluorocarbon Union Seals 1/2" to 2"-27- Latch Lock Lever 1/2" to 1-1/2"-29- Firesafe 1/2" to 2"-32- SS Tee Handle & Nut 1/2" to 1-1/2"-33- Drilled and Tapped for 1/2" to 2"

Actuator Mounting-45- Less Lever & Nut 1/2" to 2"-46- Latch Lock Lever - Lock Close Only 1/2" to 1-1/2"-49- Assembled Dry 1/2" to 2"-57- Cleaned for Gaseous Oxygen 1/2" to 2"-60- Static Grounded Ball & Stem 1/2" to 2"-63- Threaded x Solder 1/2" to 2"-64- 250 Lb. Steam Trim 1/2" to 2"-P01- BSPP (Parallel) Thread Connection 1/2" to 2"-T01- BSPT (Tapered) Thread Connection 1/2" to 2"



(1/2” to 1”)Refer to Page N-14, Graph No.12

(1-1/4” to 2”)

STAINLESS STEEL DOUBLE UNION ENDSOCKET WELD BALL VALVE


® 76-400 SeriesStainless Steel Double Union End Socket Weld Ball Valve

Socket Weld, 1/2" to 1" 2000 psig WOG, 1-1/4" to 2" 1500 psig WOG. Cold Non-Shock.150 psig Saturated Steam, Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: SS, Style: 1.

FEATURES• Heavy duty quarter turn handles • Blow-out-proof stem design• RPTFE seats and seals • Adjustable packing gland

STANDARD MATERIAL LIST1. Lever and grip 304 SS w/vinyl 9. Lever nut 18-8 SS2. Stem packing RPTFE 10. Body A351-CF8M3. Stem bearing RPTFE 11. Tailpiece (2) A276-3164. Ball A276-316 12. Union nut (2) Nitride steel5. Seat (2) RPTFE 13. Seat holder A276-3166. Retainer A276-316 14. Union seal (2) RPTFE7. Gland nut A276-316 15. Retainer seal RPTFE8. Stem A276-316

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/2" to 2"-03- 1-1/4" Stem Extension 1/2" to 1-1/2"-04- 2-1/4" Stem Extension 1/2" to 1-1/2"-07- Tee Handle 1/2" to 1-1/2"-08- 90º Reversed Stem 1/2" to 2"-14- Vented Ball(see page J-2) 1/2" to 2"-15- Round Handle 1/2" to 1-1/2"-18- Plain Yellow Grip 1/2" to 2"-22- Fluorocarbon Union Seals 1/2" to 2"-27- Latch Lock Lever 1/2" to 1-1/2"-29- Firesafe 1/2" to 2"-32- SS Tee Handle & Nut 1/2" to 2"-33- Drilled and Tapped for 1/2" to 2"

Actuator Mounting-45- Less Lever & Nut 1/2" to 2"-46- Latch Lock Lever - Lock Close Only 1/2" to 1-1/2"-49- Assembled Dry 1/2" to 2"-57- Cleaned for Gaseous Oxygen 1/2" to 2"-60- Static Grounded Ball & Stem 1/2" to 2"-64- 250 Lb. Steam Trim 1/2" to 2"



(1/2” to 1”)Refer to Page N-14, Graph No.12

(1-1/4” to 2”)

SECTION G CONTENTSSTEAM PREP BALL VALVES

DESCRIPTION PAGE

70-140-64 Series, Threaded Bronze G-1

71-140-64 Series, Threaded Bronze with Mounting Pad G-2

72-140-64 Series, Threaded High Pressure Carbon Steel G-3

73A-140-64 Series, Threaded A105 Carbon Steel G-4

73-340-64 Series, Threaded Double Union End Carbon Steel G-5

73-440-64 Series, Socket Weld Double Union End Carbon Steel G-6

76-100-64 Series, Threaded Stainless Steel with Mounting Pad G-7

76-300-64 Series, Threaded Double Union End Stainless Steel G-8

76-400-64 Series, Socket Weld Double Union End Stainless Steel G-9

83-540-64 Series, Threaded High Pressure Full Port Carbon Steel G-10with Mounting Pad

86-500-64 Series, Threaded High Pressure Full Port Stainless Steel G-11with Mounting Pad

89-140-64 Series, Threaded Carbon Steel with Mounting Pad G-12

7M-140-64 Series, Threaded Bronze with Drain & Mounting Pad G-13

G-1COPYRIGHT ©1997 CONBRACO IND., INC. – PRINTED IN U.S.A.

® 70-140-64 SeriesThreaded Bronze 250 Lb. Steam Valve


FEATURES• 316 SS ball and stem • Blow-out-proof stem design• Multifill seats • Adjustable packing gland• Multifill stuffing box ring

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 7. Gland nut B162. Stem packing Multifill PTFE 8. Stem A276-3163. Stem bearing RPTFE 9. Lever nut Steel, zinc plated4. Ball A276-316 10. Body seal PTFE5. Seat (2) Multifill PTFE (1-1/4" to 3")6. Retainer B16 (1/4" to 1") 11. Body B584-C84400

B584-C84400 (1-1/4" to 3")

NUMBER SIZE A B C D E Wt.70-141-64 1/4" .37 1.03 2.06 1.75 3.87 .5970-142-64 3/8" .37 1.03 2.06 1.75 3.87 .5570-143-64 1/2" .50 1.12 2.25 1.75 3.87 .6270-144-64 3/4" .68 1.50 3.00 2.12 4.87 1.3770-145-64 1" .87 1.68 3.37 2.25 4.87 1.7170-146-64 1-1/4" 1.00 2.00 4.00 2.62 5.50 3.2070-147-64 1-1/2" 1.25 2.18 4.37 3.06 8.00 4.5370-148-64 2" 1.50 2.34 4.68 3.25 8.00 5.8870-149-64 2-1/2" 2.50 3.25 6.50 4.12 8.00 17.0370-140-64 3" 2.50 3.37 6.75 4.12 8.00 18.25

THREADED BRONZE 250 Lb. STEAMBALL VALVE

Valves with -64 trim feature a yellowvinyl grip with distinctive red lettering.

These valves are recommended forsaturated steam to 250 psig. They arealso recommended for services withfluids with widely varying temperaturesand / or high thermal expansion rates.


®

BRONZE 250 Lb. STEAM BALL VALVEWITH MOUNTING PAD

G-2 COPYRIGHT ©1997 CONBRACO IND., INC. – PRINTED IN U.S.A.

71-140-64 SeriesBronze 250 Lb. Steam Ball Valve with Mounting Pad


FEATURES• 316 SS ball and stem • Blow-out-proof stem design• Multifill seats • Adjustable packing gland• Mounting pad for easy actuator mounting • Multifill packing

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 7. Gland nut B162. Stem packing Multifill PTFE 8. Stem A276-3163. Stem bearing RPTFE 9. Lever nut Steel, zinc plated4. Ball A276-316 10. Body seal PTFE5. Seat (2) Multifill PTFE (1-1/4" to 3")6. Retainer (3/4" to 1") B16 11. Body B584-C84400

(1-1/4" to 3") B584-C84400



NUMBER SIZE A B C D E F G H Wt.71-144-64 3/4" .68 1.50 3.00 2.12 4.87 .87 1.37 10-24 NC 1.6171-145-64 1" .87 1.68 3.37 2.25 4.87 .87 1.37 10-24 NC 1.8271-146-64 1-1/4" 1.00 2.00 4.00 2.62 5.50 .93 1.50 1/4-20 NC 3.3671-147-64 1-1/2" 1.25 2.18 4.37 2.87 8.00 .93 1.50 1/4-20 NC 4.6071-148-64 2" 1.50 2.34 4.68 3.06 8.00 .93 1.50 1/4-20 NC 5.6471-140-64 3" 2.50 3.37 6.75 4.12 8.00 N/A 2.75 1/4-20 NC 19.65


CARBON STEEL 250 Lb. STEAMHIGH PRESSURE BALL VALVE


® 72-140-64 SeriesCarbon Steel 250 Lb. Steam High Pressure Ball Valve

Threaded, 3000 psig WOG, Cold Non-Shock, 250 psig Saturated Steam.Vacuum Service to 29 inches Hg. Federal Specification: WW-V-35C, Type II, Composition: CS, Style: 3.

FEATURES• Barstock design • Adjustable packing gland• 316 SS ball and stem • Full port, except 2"• Multifill packing • Blow-out-proof stem design• Multifill seats • Heavy duty handles• Nitride corrosion protection

STANDARD MATERIAL LIST1. Lever and grip CS, zinc plated w/vinyl 7. Gland nut A108-CS2. Stem packing Multifill PTFE 8. Stem A276-3163. Stem bearing RPTFE 9. Ball A276-3164. Retainer seal RPTFE 10. Body A108-CS5. Seat (2) Multifill PTFE 11. Retainer A108-CS6. Lever nut CS, zinc plated 12. Seat holder A108-CS





CARBON STEEL 250 Lb. STEAMBALL VALVE


®73A-140-64 SeriesCarbon Steel 250 Lb. Steam Ball Valve

Threaded, 2000 psig WOG, Cold Non-Shock. 250 psig Saturated Steam.Vacuum Service to 29 inches Hg. Federal Specification: WW-V-35C, Type II, Composition: CS, Style: 3.

FEATURES• MTFE seats & packing • Raised handle stops • Nitride corrosion protection• Actuator mounting pads • Blow-out-proof stem design • 316 SS ball & stem• Forged construction • Adjustable packing gland

STANDARD MATERIAL LIST1. Lever nut Steel, zinc plated 6. Ball A276-3162. Gland nut A108-CS 7. Seat (2) RPTFE3. Stem packing MTFE 8. Body A1054. Retainer A108-1018 9. Stem bearing RPTFE5. Body seal MTFE (1/2" to 2") 10. Stem A276-316

11. Lever/grip Steel, zinc plated,with vinyl



NUMBER SIZE A B C D E73A-141-64 1/4" .37 1.02 2.53 1.72 3.8573A-142-64 3/8" .37 1.02 2.53 1.72 3.8573A-143-64 1/2" .50 1.18 2.29 1.78 3.8573A-144-64 3/4" .68 1.57 3.07 2.07 4.7573A-145-64 1" .87 1.73 3.40 2.18 4.7573A-146-64 1-1/4" 1.00 1.98 3.97 2.72 5.5073A-147-64 1-1/2" 1.25 2.14 4.32 3.12 7.7573A-148-64 2" 1.50 2.73 5.44 3.27 7.75


(1/4” to 1”)Refer to Page N-14, Graph No. 11

(1-1/4” to 2”)

CARBON STEEL 250 Lb. STEAMDOUBLE END BALL VALVE


® 73-340-64 SeriesCarbon Steel 250 Lb. Steam Double Union End Ball Valve

Threaded End, 3000 psig WOG, Cold Non-Shock, 250 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: CS, Style: 1.

FEATURES• Heavy duty quarter turn handles • Blow-out-proof stem design • Multifill packing• Adjustable packing gland • 316 SS ball and stem • Multifill seats• Easy installation and maintenance • Steel barstock design • Nitride corrosion protection

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 9. Lever Steel, zinc plated2. Stem packing Multifill PTFE 10. Body A108-CS3. Stem bearing RPTFE 11. Tailpiece (2) A108-CS4. Ball A276-316 12. Union nut (2) A108-CS5. Seat (2) Multifill PTFE 13. Seat holder A108-CS6. Retainer A108-CS 14. Union seal (2) RPTFE7. Gland nut A108-CS 15. Retainer seal RPTFE8. Stem A276-316





CARBON STEEL 250 Lb. STEAM DOUBLEUNION END SOCKET WELD BALL VALVE


® 73-440-64 SeriesCarbon Steel 250 Lb. Steam Double Union End

Socket Weld Ball ValveSocket Weld, 3000 psig WOG, Cold Non-Shock, 250 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: CS, Style: 1.

FEATURES• Heavy duty quarter turn handles • Blow-out-proof stem design • Multifill packing• Adjustable packing gland • 316 SS ball and stem • Multifill seats• Easy installation and maintenance • Steel barstock design • Nitride corrosion protection

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 9. Lever nut Steel, zinc plated2. Stem packing Multifill PTFE 10. Body A108-CS3. Stem bearing RPTFE 11. Tailpiece (2) A108-CS4. Ball A276-316 12. Union nut (2) A108-CS5. Seat (2) Multifill PTFE 13. Seat holder A108-CS6. Retainer A108-CS 14. Union seal (2) RPTFE7. Gland nut A108-CS 15. Retainer seal RPTFE8. Stem A276-316





STAINLESS STEEL 250 Lb. STEAMBALL VALVE


® 76-100-64 SeriesStainless Steel 250 Lb. Steam Ball Valve

Threaded, 1/4" to 1" 2000 psig WOG; 1-1/4" to 2" 1500 psig WOG; 2-1/2" to 3" 1000 psig WOGCold Non-Shock. 250 psig Saturated Steam, Vacuum Service to 29 inches Hg. Federal Specification: WW-V-35C, Type II, Composition: SS, Style: 3.

FEATURES• Investment cast components • Blow-out-proof stem design • Multifill packing• Adjustable packing gland • 316 SS ball and stem • Multifill seats• Meets NACE MR-01-75 • Mounting pad for easy actuator mounting

STANDARD MATERIAL LIST1. Lever and grip 304 SS w/vinyl 7. Gland nut A276-3162. Stem packing Multifill PTFE 8. Stem A276-3163. Stem bearing RPTFE 9. Lever nut 304 SS4. Ball A276-316 10. Body seal PTFE5. Seat (2) Multifill PTFE (1-1/4" to 3")6. Retainer A276-316 (1/4" to 1") 11. Body A351-CF8M

A351-CF8M (1-1/4" & Up)






(1-1/4” to 2”)Refer to Page N-14, Graph No. 8

(2-1/2” to 3”)

STAINLESS STEEL 250 Lb. STEAMDOUBLE UNION END BALL VALVE


® 76-300-64 SeriesStainless Steel 250 Lb. Steam Double Union End

Ball ValveThreaded, 1/2"-1" 2000 psig WOG, 1-1/4" to 2" 1500 psig WOG. Cold Non-Shock.250 psig Saturated Steam, Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: SS, Style: 1.

FEATURES• 316 SS ball and stem • Blow-out-proof stem design • Multifill packing• Adjustable packing gland • Multifill seats

STANDARD MATERIAL LIST1. Lever and grip 304 SS w/vinyl 9. Lever nut 304 SS2. Stem packing Multifill PTFE 10. Body A351-CF8M3. Stem bearing RPTFE 11. Tailpiece (2) A276-3164. Ball A276-316 12. Union nut (2) A108-CS, Nitride5. Seat (2) Multifill PTFE 13. Seat holder A276-3166. Retainer A276-316 14. Union seal (2) RPTFE7. Gland nut A276-316 15. Retainer seal RPTFE8. Stem A276-316






(1-1/4” to 2”)


® 76-400-64 SeriesStainless Steel 250 Lb. Steam Double Union End

Socket Weld Ball ValveSocket Weld, 1/2" to 1" 2000 psig WOG, 1-1/4" to 2" 1500 psig WOG. Cold Non-Shock.250 psig Saturated Steam, Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: SS, Style: 1.

FEATURES• 316 SS ball and stem • Blow-out-proof stem design • Multifill packing• Adjustable packing gland • Multifill seats

STANDARD MATERIAL LIST1. Lever and grip 304 SS w/vinyl 9. Lever nut 304 SS2. Stem packing Multifill PTFE 10. Body A351-CF8M3. Stem bearing RPTFE 11. Tailpiece (2) A276-316L4. Ball A276-316 12. Union nut (2) A108-CS, Nitride5. Seat (2) Multifill PTFE 13. Seat holder A276-3166. Retainer A276-316 14. Union seal (2) RPTFE7. Gland nut A276-316 15. Retainer seal RPTFE8. Stem A276-316


STAINLESS STEEL 250 Lb. STEAM DOUBLEUNION END SOCKET WELD BALL VALVE





(1-1/4” to 2”)

CARBON STEEL 250 Lb. STEAM HIGH PRESSUREFULL PORT BALL VALVE


® 83-540-64 SeriesCarbon Steel 250 Lb. Steam 3-Piece High Pressure

Full Port Ball ValveThreaded, 1500 psig WOG, Cold Non-Shock, 250 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: CS, Style: 1.

FEATURES• Multifill seats • Blow-out-proof stem design • In-line repairable• 316 SS ball and stem • Adjustable packing gland • Multifill packing• Investment Cast Components • Actuator mounting pad (3/4" to 2") • Nitride corrosion protection

STANDARD MATERIAL LIST1. Lever and grip CS, zinc plated w/vinyl 8. Gland nut A108-CS2. Stem packing Multifill PTFE 9. Stem A276-3163. Stem bearing RPTFE 10. Lever nut 18-8 SS4. Ball A276-316 11. Seat (2) Multifill PTFE5. Body bolt (4) Steel, SAE grade 8 zinc plated 12. End cap (2) A216-WCB6. Hex nut (4) Steel, SAE grade 8 zinc plated 13. Body A216-WCB7. Seat holder (2) A108-CS 14. Body seal (2) Graphite



NUMBER SIZE A B C D E F G Wt.83-541-64 1/4" .43 1.50 3.00 1.93 3.87 N/A N/A 1.2183-542-64 3/8" .50 1.50 3.00 1.93 3.87 N/A N/A 1.2283-543-64 1/2" .62 1.69 3.38 2.00 4.81 N/A N/A 1.9083-544-64 3/4" .81 1.93 3.87 2.18 4.81 1.25 1/4-20 2.5683-545-64 1" 1.00 2.25 4.50 2.62 5.50 1.62 5/16-18 3.7883-546-64 1-1/4" 1.25 2.43 4.87 2.87 5.50 1.62 5/16-18 5.2483-547-64 1-1/2" 1.50 2.62 5.25 3.35 8.00 1.62 5/16-18 7.6783-548-64 2" 2.00 3.12 6.25 3.75 8.00 1.62 5/16-18 15.60

Tapping


1/00

STAINLESS STEEL 250 Lb. STEAM 3-PIECEHIGH PRESSURE FULL PORT BALL VALVE


® 86-500-64 SeriesStainless Steel 250 Lb. Steam 3-Piece High Pressure

Full Port Ball ValveThreaded, 1500 psig WOG, Cold Non-Shock, 250 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: SS, Style: 1.

FEATURES• Multifill seats • Meets NACE MR-01-75 • Blow-out-proof stem design• In-line repairable • 316 SS ball and stem • Adjustable packing gland• Investment Cast Components • Actuator mounting pad (3/4" to 2") • Multifill packing

STANDARD MATERIAL LIST1. Lever and grip 304 SS w/vinyl 8. Gland nut A276-3162. Stem packing Multifill PTFE 9. Stem A276-3163. Stem bearing RPTFE 10. Lever nut 304 SS4. Ball A276-316 11. Body bolt (4) 18-8 SS5. Seat (2) Multifill PTFE 12. Hex nut (4) 18-8 SS6. End cap (2) A351-CF3M 13. Body A351-CF8M7. Seat holder (2) A276-316 14. Body seal (2) Graphite



NUMBER SIZE A B C D E F G Wt.86-501-64 1/4" .43 1.50 3.00 1.93 3.87 N/A N/A 1.2386-502-64 3/8" .50 1.50 3.00 1.93 3.87 N/A N/A 1.1886-503-64 1/2" .62 1.69 3.38 2.00 4.81 N/A N/A 1.6286-504-64 3/4" .81 1.93 3.87 2.18 4.81 1.25 1/4-20 2.2786-505-64 1" 1.00 2.25 4.50 2.62 5.50 1.62 5/16-18 3.5486-506-64 1-1/4" 1.25 2.43 4.87 2.87 5.50 1.62 5/16-18 6.0086-507-64 1-1/2" 1.50 2.62 5.25 3.35 8.00 1.62 5/16-18 8.8486-508-64 2" 2.00 3.12 6.25 3.75 8.00 1.62 5/16-18 15.28

Tapping


1/00

CARBON STEEL 250 Lb. STEAM BALL VALVE


®


89-140-64 SeriesCarbon Steel 250 Lb. Steam Ball Valve

Threaded, 1/4" to 1" 2000 psig WOG; 1-1/4" to 2" 1500 psig WOG; 2-1/2" to 3" 1000 psig WOGCold Non-Shock, 250 psig Saturated Steam, Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: CS, Style: 3.

FEATURES• Investment cast components • Blow-out-proof stem design• Multifill packing • Adjustable packing gland• Mounting pad for easy actuator mounting • Multifill seats• 316 SS ball and stem • Nitride corrosion protection

STANDARD MATERIAL LIST1. Lever and grip CS, zinc plated w/vinyl 7. Gland nut A108-CS2. Stem packing Multifill PTFE 8. Stem A276-3163. Stem bearing RPTFE 9. Seat (2) Multifill PTFE4. Ball A276-316 10. Body seal PTFE5. Lever nut CS, zinc plated (1-1/4" to 3")6. Retainer A108-CS (1/4" to 1") 11. Body A216-WCB

A216-WCB (1-1/4" to 3")





(1-1/4” to 2”)


® 7M-140-64 SeriesBronze 250 lb. Steam Full Port Ball Valve with Drain

NPT Threaded with NPT threaded drain port. Drain port plug standard.600 psig WOG, cold non-shock. 250 psig saturated steam.Vacuum service to 29 inches of Hg.

FEATURES• Stainless steel ball & stem • Blow-out-proof stem design• MPTFE seats and stuffing box ring • Adjustable packing gland• Mounting pad for easy actuator mounting • Full port for full flow & min. pressure drop

(3/4" to 2-1/2") • Use for draining systems

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 7. Gland nut 85-5-5-52. Stem packing MPTFE 8. Stem A276 - 3163. Stem bearing RPTFE 9. Lever nut Steel, zinc plated4. Ball A276 - 316 10. Body seal (1-1/4" to 2") PTFE5. Seat (2) MPTFE (1-1/4" to 2-1/2")6. Retainer 85-5-5-5 (1/4" to 1") 11. Body B62 - C83600

B62 - C83600 (1-1/4" to 2-1/2") 12. Pipe plug 85-5-5-5

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/4" to 2-1/2"-03- 1-1/4" Stem Extension 1/4" to 2-1/2"-04- 2-1/4" Stem Extension 1/4" to 2-1/2"-07- Tee Handle 1/4" to 1-1/4"-08- 90º Reversed Stem 1/4" to 2-1/2"-10- SS Lever & Nut 1/4" to 2-1/2"-15- Round Handle 1/4" to 1-1/4"-16- Vertical Chain Lever 3/4" to 2-1/2"-17- Rough Chrome Plating 1/4" to 2-1/2"-18- Plain Yellow Grip 1/4" to 2-1/2"-24- Graphite Stem Packing 1/4" to 2-1/2"-27- Latch Lock Lever 1/4" to 2-1/2"-30- CamLock Handle 1/4" to 2-1/2"-32- SS Tee Handle & Nut 1/4" to 2-1/2"-40- Cyl-Loc 1/4" to 1-1/4"-45- Less Lever & Nut 1/4" to 2-1/2"-46- Latch Lock Lever - Lock Close Only 1/4" to 2-1/2"-47- SS Latch-Lock Oval Handle 1/4" to 3/4"-48- SS Oval Handle 1/4" to 2"-49- Assembled Dry 1/4" to 2-1/2"-50- 2-1/4” Locking Stem Extension 1/4" to 2-1/2"-57- Cleaned for Gaseous Oxygen 1/4" to 2-1/2"-58- Horizontal Chain Lever 3/4" to 2-1/2"-60- Static Grounded Ball & Stem 1/4" to 2-1/2"

NUMBER SIZE A B C D E F G H I J K Wt.7M-141-01 1/4" .37 1.03 2.06 1.75 3.87 N/A N/A .09 .53 1.18 N/A .707M-142-01 3/8" .37 1.03 2.06 1.75 3.87 N/A N/A .09 .53 1.18 N/A .667M-143-01 1/2" .50 1.10 2.19 1.75 3.87 N/A N/A .12 .59 1.25 N/A .737M-144-01 3/4" .81 1.56 3.12 2.12 4.78 .87 1.37 .29 .90 1.56 .90 1.937M-145-01 1" 1.00 1.80 3.61 2.62 5.50 .93 1.50 .31 1.12 1.78 1.12 3.427M-146-01 1-1/4" 1.25 2.12 4.25 2.87 5.50 .93 1.50 .37 1.37 2.03 1.37 5.157M-147-01 1-1/2" 1.50 2.37 4.74 3.30 7.78 2.08 3.06 .50 1.56 2.21 1.28 6.817M-148-01 2" 2.00 2.70 5.38 3.71 7.78 2.41 3.52 .62 2.03 2.68 1.56 11.857M-149-01 2-1/2" 2.50 3.25 6.50 4.05 7.78 2.75 3.37 1.09 2.34 3.00 2.00 17.35

BRONZE 250 LB. STEAM FULL PORT BALL VALVE WITH DRAIN

1/00

SECTION D CONTENTSANSI FLANGED BALL VALVES

DESCRIPTION PAGE87A-100 Series, ANSI Class 150 Flanged Stainless Steel-1-1/2" through 2" (New Item) D-1

87A-100 Series Stainless Steel ANSI Class 150 Flanged Std. Port Ball Valve - 2-1/2" through 3" (New Item) D-2

87A-100 Series Stainless Steel ANSI Class 150 Flanged Std. Port Ball Valve - 4" through 8 (New Item) D-3

87A-200 Series, ANSI Class 150 Flanged Full Port Stainless Steel-1/2" through 1" (New Item) D-4

87A-200 Series, ANSI Class 150 Flanged Full Port Stainless Steel-1-1/2" through 2-1/2" (New Item) D-5

87A-200 Series, ANSI Class 150 Flanged Full Port Stainless Steel-3" through 6" (New Item) D-6

87A-400 Series, ANSI Class 150 Flanged Alloy 20 1/2" through 1" (New Item) D-57

87A-400 Series, ANSI Class 150 Flanged Alloy 20 1-1/2" through 2" (New Item) D-58

87A-400 Series, ANSI Class 150 Flanged Alloy 20 3" (New Item) D-59

87A-400 Series, ANSI Class 150 Flanged Alloy 20 4" (New Item) D-60

87A-700 Series, ANSI Class 300 Flanged Stainless Steel-1-1/2" through 2" (New Item) D-7

87A-700 Series, ANSI Class 300 Flanged Stainless Steel- 2-1/2" through 3" (New Item) D-8

87A-700 Series, ANSI Class 300 Flanged Stainless Steel- 4" through 8" (New Item) D- 9

87A-900 Series, ANSI Class 300 Flanged Full Port Stainless Steel-1/2" through 1" (New Item) D-10

87A-900 Series, ANSI Class 300 Flanged Full Port Stainless Steel-1-1/2" through 2-1/2" (New Item) D-11

87A-900 Series, ANSI Class 300 Flanged Full Port Stainless Steel-3" through 6" (New Item) D-12

88A-100 Series, ANSI Class 150 Flanged Carbon Steel-1-1/2" through 2" (New Item) D-13

88A-100 Series, ANSI Class 150 Flanged Carbon Steel- 2-1/2" through 3" (New Item) D-14

88A-100 Series, ANSI Class 150 Flanged Carbon Steel- 4" through 8" (New Item) D-15

88A-200 Series, ANSI Class 150 Flanged Full Port Carbon Steel-1/2" through 1" (New Item) D-16

88A-200 Series, ANSI Class 150 Flanged Full Port Carbon Steel-1-1/2" through 2-1/2" (New Item) D-17

88A-200 Series, ANSI Class 150 Flanged Full Port Carbon Steel-3" through 6" (New Item) D-18

88A-700 Series, ANSI Class 300 Flanged Carbon Steel-1-1/2 through 2” (New Item) D-19

88A-700 Series, ANSI Class 300 Flanged Carbon Steel- 2-1/2" through 3" (New Item) D-20

88A-700 Series, ANSI Class 300 Flanged Carbon Steel- 4" through 8" (New Item) D-21

88A-900 Series, ANSI Class 300 Flanged Full Port Carbon Steel-1/2" through 1" (New Item) D-22

88A-900 Series, ANSI Class 300 Flanged Full Port Carbon Steel-1-1/2" through 2-1/2" (New Item) D-23

88A-900 Series, ANSI Class 300 Flanged Full Port Carbon Steel-3" through 6"" (New Item) D-24

87-100 Series, ANSI Class 150 Flanged Stainless Steel - 1/2" through 1" D-25

87-100 Series, ANSI Class 150 Flanged Stainless Steel - 1-1/2" through 2-1/2" D-26

87-100 Series, ANSI Class 150 Flanged Stainless Steel - 3" through 10" D-27

87-200 Series, ANSI Class 150 Flanged Full Port Stainless Steel- 1” D-28

87-200 Series, ANSI Class 150 Flanged Full Port Stainless Steel- 1-1/2” to 2-1/2” D-29

87-200 Series, ANSI Class 150 Flanged Full Port Stainless Steel- 3” to 6” D-30

87-200 Series, ANSI Class 150 Flanged Full Port Stainless Steel- 8” to 12” D-31

87-700 Series, ANSI Class 300 Flanged Stainless Steel - 2” D-32

87-700 Series, ANSI Class 300 Flanged Stainless Steel - 3” through 10” D-33

87-808 Series, 2" ANSI Class 600 Flanged Stainless Steel D-34

88-808 Series, 2" ANSI Class 600 Flanged Carbon Steel D-35

87-900 Series, ANSI Class 300 Flanged Full Port Stainless Steel - 1/2” through 1 1/2” D-36

87-900 Series, ANSI Class 300 Flanged Full Port Stainless Steel - 2” D-37

87-900 Series, ANSI Class 300 Flanged Full Port Stainless Steel - 3” through 6” D-38

87-900 Series, ANSI Class 300 Flanged Full Port Stainless Steel - 8” D-39

88-100 Series, ANSI Class 150 Flanged Carbon Steel - 1/2”through 1” D-40

88-100 Series, ANSI Class 150 Flanged Carbon Steel - 1-1/2”through 2-1/2” D-41

88-100 Series, ANSI Class 150 Flanged Carbon Steel - 3” through 10” D-42

88-200 Series, ANSI Class 150 Flanged Full Port Carbon Steel -1” D-43

88-200 Series, ANSI Class 150 Flanged Full Port Carbon Steel -1-1/2” through 2-1/2” D-44

88-200 Series, ANSI Class 150 Flanged Full Port Carbon Steel - 3” through 6” D-45


88-700 Series, ANSI Class 300 Flanged Carbon Steel - 2” D-47

88-700 Series, ANSI Class 300 Flanged Carbon Steel - 3” through 10” D-48

88-900 Series, ANSI Class 300 Flanged Full Port Carbon Steel -1/2”through 1 1/2” D-49

88-900 Series, ANSI Class 300 Flanged Full Port Carbon Steel - 2” D-50


88-900 Series, ANSI Class 300 Flanged Full Port Carbon Steel - 8” D-52

452-200 Series, ANSI Class 150 Flanged Full Port Extended - 1/2”through 2” D-53

452-200 Series, ANSI Class 150 Flanged Full Port Extended - 3” through 6” D-54

Bonnet Stainless Steel

453-200 Series, ANSI Class 150 Flanged Full Port Extended - 1/2” through 2” D-55

453-200 Series, ANSI Class 150 Flanged Full Port Extended - 3” through 6” D-56

NUMBER SIZE A B C D E F G H I J K L M N WT.87A-107-01 1-1/2" 1.00 6.50 3.69 3.62 6.03 0.47 1.62 2.15 1.392 0.696 0.500 0.287 1/4-20 1.50 9.087A-108-01 2" 1.50 7.00 3.69 4.62 6.65 0.72 2.41 3.09 1.949 0.974 0.625 0.412 5/16-18 2.00 18.0

D-1COPYRIGHT ©1999 CONBRACO IND., INC. – PRINTED IN U.S.A.

®

OPTIONS AVAILABLE:(SUFFIX) OPTION-01- Standard (Locking Kit and Grounded Stem)-14- Side Vented Ball (See Page J-2)-15- Wheel Handle-21- UHMWPE Seats-24- Fire Safe (Graphite Packing and Seal)-35- PTFE Seats and Seals-38- PEEK Seats and Graphite Packing-49- Assembled Dry-57- Oxygen Cleaned-60- Grounded Ball and Stem-65- MPTFE Seats and Graphite Packing-67- Cleaned For Industrial Gases-69- Drilled and Tapped Purge Port with Plug-70- 4" Extended Bonnet-73- 316 SS Spiral Wound Gaskets w/PTFE Filler-74- 316 SS Spiral Wound Gaskets w/Graphite Filler

MATERIALS OFCONSTRUCTIONDescription Material1. Body ASTM A351 CF8M2. Retainer ASTM A276 Type 3163. Ball ASTM A276 Type 3164. Stem ASTM A276 Type 3165. Packing Gland ASTM A276 Type 3166. Stem Seals PTFE7. Seats RPTFE8. Gland Screws ASTM A193 B8 Class 19. Gland Plate 302 or 304 SS

10. Stem Nut 316 SS11. Lever 302 or 304 SS with Vinyl Grip12. Stem Bearing RPTFE13. Stop ASTM A276 Type 31614. Stop Screw 18-8 SS15. Lock Plate 302 or 304 SS16. Body Seal RPTFE17. Lockwasher 302 or 304 SS18. Grounding Spring SS


87A-100 SeriesStainless Steel ANSI Class 150 Flanged Std. Port Ball Valve -

1-1/2" through 2"STANDARDS COMPLIANCEASME B16.5 - "Pipe Flanges and Flanged Fittings"ASME B16.10 - "Face to Face Dimensions of Valves"ASME B16.34 - "Valves - Flanged, Threaded, and

Welding End"API 607 - "Fire Test - Soft Seated Quarter Turn

Valves" (-24 option)API 608 - "Ball Valves - Flanged, Threaded, and

Welding End"MSS SP-25 - "Standard Marking System for Valves"MSS SP-61 - "Pressure Testing of Steel Valves"MSS SP-72 - "Ball Valves with Flanged or

Buttwelding Ends"ASME B31.1, - Pressure Piping StandardsB31.3, & B31.8

STANDARD FEATURESTwo Position Locking DeviceAntistatic Grounded StemCHV Style Adjustable Stem SealsBlow-out Proof Stem DesignCast Boss for Bleed / Drain PortFour Point ISO 5211 Mounting Pad Bolt CircleSlot Vented Ball for Thermal ExpansionVacuum Service to 29 inches Hg

1/00

D-2 COPYRIGHT ©1999 CONBRACO IND., INC. – PRINTED IN U.S.A.


®87A-100 SeriesStainless Steel ANSI Class 150 Flanged Std. Port Ball Valve -

2-1/2" through 3"

OPTIONS AVAILABLE:(SUFFIX) OPTION-01- Standard (Locking Kit and Grounded Stem)-14- Side Vented Ball (See Page J-2)-21- UHMWPE Seats-24- Fire Safe (Graphite Packing and Seal)-35- PTFE Seats and Seals-38- PEEK Seats and Graphite Packing-49- Assembled Dry-57- Oxygen Cleaned-60- Grounded Ball and Stem-65- MPTFE Seats and Graphite Packing-67- Cleaned For Industrial Gases-69- Drilled and Tapped Purge Port with Plugs-70- 4" Extended Bonnet-73- 316 SS Spiral Wound Gaskets w/PTFE Filler-74- 316 SS Spiral Wound Gaskets w/Graphite Filler-MG- Gear Operator with Standard Handwheel-MH- Gear Operator with Standard Handwheel &

Locking Device-MJ- Gear Operator with Oversize Handwheel-MK- Gear Operator with Oversize Handwheel &

Locking Device

MATERIALS OFCONSTRUCTIONDescription Material1. Body ASTM A351 CF8M2. Retainer ASTM A351 CF8M3. Ball ASTM A276 Type 316 or A351 CF8M4. Stem ASTM A276 Type 3165. Packing Gland ASTM A276 Type 3166. Stem Seals PTFE7. Seats RPTFE8. Gland Screws ASTM A193 B8 Class 19. Gland Plate 316 SS

10. Stem Nut 18-8 SS11. Lever 316 SS12. Stem Bearing RPTFE13. Stop ASTM A276 Type 31614. Stop Screw 316 SS15. Lock Plate 302 or 304 SS16. Body Seal RPTFE17. Grounding Spring SS18. Body Joint Stud ASTM A194 Grade B8M19. Body Joint Nut ASTM A194 Grade 820. Lockwasher 302 or 304 SS


STANDARDS COMPLIANCEASME B16.5 - "Pipe Flanges and Flanged Fittings"ASME B16.10 - "Face to Face Dimensions of Valves"ASME B16.34 - "Valves - Flanged, Threaded, and





STANDARD FEATURESTwo Position Locking DeviceAntistatic Grounded StemCHV Style Adjustable Stem SealsBlow-out Proof Stem DesignCast Bosses for Bleed / Drain PortsFour Point ISO 5211 Mounting Pad Bolt CircleSlot Vented Ball for Thermal ExpansionVacuum Service to 29 inches Hg

1/00


NUMBER SIZE A B C D E F G H I J K L M N WT.87A-10A-01 4" 3.00 9.00 4.18 8.80 3.88 0.50 4.75 5.95 2.840 1.420 1.250 0.725 3/8-16 4.00 73.087A-10C-01 6" 4.00 10.50 4.69 9.99 5.13 0.50 5.94 7.13 2.840 1.420 1.250 0.725 3/8-16 6.00 117.087A-10E-01 8" 6.00 18.00 9.00 13.73 7.00 1.00 7.75 9.48 4.596 2.298 2.000 1.375 3/4-10 8.00 310.0

®

OPTIONS AVAILABLE:(SUFFIX) OPTION-01- Standard (Locking Kit and Grounded Stem)-14- Side Vented Ball (See Page J-2)-21- UHMWPE Seats-24- Fire Safe (Graphite Packing and Seal)-35- PTFE Seats and Seals-49- Assembled Dry-57- Oxygen Cleaned-60- Grounded Ball and Stem-65- MPTFE Seats and Graphite Packing-67- Cleaned For Industrial Gases-69- Drilled and Tapped Purge Ports with Plugs-70- 4" Extended Bonnet (4" & 6" Valves Only)-73- 316 SS Spiral Wound Gaskets w/PTFE Filler-74- 316 SS Spiral Wound Gaskets w/Graphite Filler-MG- Gear Operator with Standard Handwheel-MH- Gear Operator with Standard Handwheel &


Locking Device









4" through 8"


10. Adapter Screw 18-8 SS11. Handle Adapter 316 SS12. Stem Bearing RPTFE13. Stop ASTM A276 Type 31614. Stop Screw 316 SS15. Lock Plate 302 or 304 SS16. Body Seal RPTFE17. Grounding Spring SS18. Body Joint Stud ASTM A194 Grade B8M19. Body Joint Nut ASTM A194 Grade 820. Lockwasher 302 or 304 SS21. Pipe Handle Galvanized Steel (not Shown)

1/00


NUMBER SIZE A B C D E F G H I J K L M WT.87A-203-01 1/2" 0.50 4.25 2.06 3.28 5.14 .30 1.09 1.38 1.002 .501 .376 .250 1/4-20 5.087A-204-01 3/4" 0.75 4.62 2.18 3.89 5.56 .39 1.65 1.96 1.392 .696 .500 .287 1/4-20 6.087A-205-01 1" 1.00 5.00 2.32 3.62 6.03 0.47 1.62 2.15 1.392 0.696 0.500 0.287 1/4-20 7.0

®87A-200 SeriesStainless Steel ANSI Class 150 Flanged Full Port Ball Valve -

1/2" through 1"

OPTIONS AVAILABLE:(SUFFIX) OPTION-01- Standard (Locking Kit and Grounded Stem)-14- Side Vented Ball (See Page J-2)-15- Wheel Handle-21- UHMWPE Seats-24- Fire Safe (Graphite Packing and Seal)-35- PTFE Seats and Seals-38- PEEK Seats and Graphite Packing-49- Assembled Dry-57- Oxygen Cleaned-60- Grounded Ball and Stem-65- MPTFE Seats and Graphite Packing-67- Cleaned For Industrial Gases-69- Drilled and Tapped Purge Port with Plugs-70- 4" Extended Bonnet-73- 316 SS Spiral Wound Gaskets w/PTFE Filler-74- 316 SS Spiral Wound Gaskets w/Graphite Filler


10. Stem Nut 316 SS11. Lever 302 or 304 with Vinyl Grip12. Stem Bearing RPTFE13. Stop ASTM A276 Type 31614. Stop Screw 18-8 SS15. Lock Plate 302 or 304 SS16. Body Seal RPTFE17. Lockwasher 302 or 304 SS18. Grounding Spring SS







STANDARD FEATURESTwo Position Locking DeviceAntistatic Grounded StemCHV Style Adjustable Stem SealsBlow-out Proof Stem DesignCast Boss for Bleed / Drain PortFour Point ISO 5211 Mounting Pad Bolt CircleFull Bore Design for Maximum Flow EfficiencySlot Vented Ball for Thermal ExpansionVacuum Service to 29 inches Hg

1/00

D-5COPYRIGHT ©1999 CONBRACO IND., INC. – PRINTED IN U.S.A. REVISED 12/99

NUMBER SIZE A B C D E F G H I J K L M WT.87A-207-01 1-1/2" 1.50 6.50 3.00 4.62 6.65 0.72 2.41 3.09 1.949 0.974 0.625 0.412 5/16-18 14.087A-208-01 2" 2.00 7.00 3.04 5.61 8.40 0.80 3.31 4.08 1.949 0.974 0.750 0.477 5/16-18 25.087A-209-01 2-1/2 2.50 7.50 3.34 6.23 8.40 0.80 3.93 4.70 1.949 0.974 0.750 0.477 5/16-18 30.0

®








87A-200 SeriesStainless Steel ANSI Class 150 Flanged Full Port Ball Valve -

1-1/2" through 2-1/2"


10. Adapter Screw 18-8 SS11. Lever 316 SS12. Stem Bearing RPTFE13. Stop ASTM A276 Type 31614. Stop Screw 316 SS15. Lock Plate 302 or 304 SS16. Body Seal RPTFE17. Grounding Spring SS18. Body Joint Stud ASTM A193 Grade B8M19. Body Joint Nut ASTM A194 Grade 820. Lockwasher 302 or 304 SS

1/00

OPTIONS AVAILABLE:(SUFFIX) OPTION-01- Standard (Locking Kit and Grounded Stem)-14- Side Vented Ball (See Page J-2)-21- UHMWPE Seats-24- Fire Safe (Graphite Packing and Seal)-35- PTFE Seats and Seals-38- PEEK Seats and Graphite Packing (3" Only)-49- Assembled Dry-57- Oxygen Cleaned-60- Grounded Ball and Stem-65- MPTFE Seats and Graphite Packing-67- Cleaned For Industrial Gases-69- Drilled and Tapped Purge Ports with Plugs-70- 4" Extended Bonnet-73- 316 SS Spiral Wound Gaskets w/PTFE Filler-74- 316 SS Spiral Wound Gaskets w/Graphite Filler-MG- Gear Operator with Standard Handwheel-MH- Gear Operator with Standard Handwheel &


Locking Device


NUMBER SIZE A B C D E F G H I J K L M WT.87A-200-01 3" 3.00 8.00 3.68 8.80 3.88 0.50 4.75 5.95 2.840 1.420 1.250 0.725 3/8-16 60.087A-20A-01 4" 4.00 9.00 3.94 9.99 5.13 0.50 5.94 7.13 2.840 1.420 1.250 0.725 3/8-16 91.087A-20C-01 6" 6.00 15.50 7.19 13.73 7.00 1.00 7.75 9.48 4.596 2.298 2.000 1.375 3/4-10 248.0


3" through 6"

OPTIONS AVAILABLE:(SUFFIX) OPTION-01- Standard (Locking Kit and Grounded Stem)-14- Side Vented Ball (See Page J-2)-21- UHMWPE Seats-24- Fire Safe (Graphite Packing and Seal)-35- PTFE Seats and Seals-38- PEEK Seats and Graphite Packing (3" Only)-49- Assembled Dry-57- Oxygen Cleaned-60- Grounded Ball and Stem-65- MPTFE Seats and Graphite Packing-67- Cleaned For Industrial Gases-69- Drilled and Tapped Purge Ports with Plugs-70- 4" Extended Bonnet (3" & 4" Valves Only)-73- 316 SS Spiral Wound Gaskets w/PTFE Filler-74- 316 SS Spiral Wound Gaskets w/Graphite Filler-MG- Gear Operator with Standard Handwheel-MH- Gear Operator with Standard Handwheel &


Locking Device


10. Adapter Screw 18-8 SS11. Handle Adapter 316 with Vinyl Grip12. Stem Bearing RPTFE13. Stop ASTM A276 Type 31614. Stop Screw 316 SS15. Lock Plate 302 or 304 SS16. Body Seal RPTFE17. Grounding Spring SS18. Body Joint Stud ASTM A193 Grade B8M19. Body Joint Nut ASTM A194 Grade 820. Pipe Handle Galvanized Steel (not shown)







STANDARD FEATURESTwo Position Locking DeviceAntistatic Grounded StemCHV Style Adjustable Stem SealsBlow-out Proof Stem DesignCast Bosses for Bleed / Drain PortsFour Point ISO 5211 Mounting Pad Bolt CircleFull Bore Design for Maximum Flow EfficiencySlot Vented Ball for Thermal ExpansionVacuum Service to 29 inches Hg

1/00



®

OPTIONS AVAILABLE:(SUFFIX) OPTION-01- Standard (Locking Kit and Grounded Stem)-14 - Side Vented Ball (See Page J-2)-15- Wheel Handle-21 - UHMWPE Seats-24 - Fire Safe (Graphite Packing and Seal)-35 - PTFE Seats and Seals-38- PEEK Seats and Graphite Packing-49- Assembled Dry-57- Oxygen Cleaned-60- Grounded Ball and Stem-65- MPTFE Seats and Graphite Packing-67- Cleaned For Industrial Gases-69- Drilled and Tapped Purge Ports with Plugs-70- 4" Extended Bonnet-73- 316 SS Spiral Wound Gaskets w/PTFE Filler-74- 316 SS Spiral Wound Gaskets w/Graphite Filler

MATERIALS OFCONSTRUCTIONDescription Material1. Body ASTM A351 CF8M2. Retainer ASTM A276 Type 3163. Ball ASTM A276 Type 3164. Stem ASTM A276 Type 3165. Packing Gland ASTM A276 Type 3166. Stem Seals PTFE7. Seats RPTFE8. Gland Screws ASTM A193 B8 Class 19. Gland Plate 302 & 304 SS

10. Stem Nut 316 SS11. Lever 302 & 304 SS with Vinyl Grip12. Stem Bearing RPTFE13. Stop ASTM A276 Type 31614. Stop Screw 18-8 SS15. Lock Plate 302 or 304 SS16. Body Seal RPTFE17. Lockwasher 302 or 304 SS18. Grounding Spring SS









1-1/2" through 2"

1/00



®87A-700 SeriesStainless Steel ANSI Class 300 Flanged Std. Port Ball Valve -

2-1/2" through 3"


10. Stem Nut 18-8 SS11. Lever 316 with Vinyl Grip12. Stem Bearing RPTFE13. Stop ASTM A276 Type 31614. Stop Screw 316 SS15. Lock Plate 302 or 304 SS16. Body Seal RPTFE17. Grounding Spring SS18. Body Joint Stud ASTM A193 Grade B8M19. Body Joint Nut ASTM A194 Grade 820. Lockwasher 302 or 304 SS

STANDARDS COMPLIANCEASME B16.5- "Pipe Flanges and Flanged Fittings"ASME B16.10- "Face to Face Dimensions of Valves"ASME B16.34- "Valves - Flanged, Threaded, and

Welding End"API 607- "Fire Test - Soft Seated Quarter Turn

Valves" (-24 option)API 608- "Ball Valves - Flanged, Threaded, and

Welding End"MSS SP-25- "Standard Marking System for Valves"MSS SP-61- "Pressure Testing of Steel Valves"MSS SP-72- "Ball Valves with Flanged or

Buttwelding Ends"ASME B31.1,- Pressure Piping StandardsB31.3, & B31.8


OPTIONS AVAILABLE:(SUFFIX) OPTION-01- Standard (Locking Kit and Grounded Stem)-14- Side Vented Ball (See Page J-2)-21- UHMWPE Seats-24- Fire Safe (Graphite Packing and Seal)-35- PTFE Seats and Seals-38- PEEK Seats and Graphite Packing-49- Assembled Dry-57- Oxygen Cleaned -60- Grounded Ball and Stem-65- MPTFE Seats and Graphite Packing-67- Cleaned For Industrial Gases-69- Drilled and Tapped Purge Ports with Plugs-70- 4" Extended Bonnet-73- 316 SS Spiral Wound Gaskets w/PTFE Filler-74- 316 SS Spiral Wound Gaskets w/Graphite Filler-MG- Gear Operator with Standard Handwheel-MH- Gear Operator with Standard Handwheel &


Locking Device


1/00



®

MATERIALS OFCONSTRUCTIONDescription Material1. Body ASTM A351 CF8M2. Retainer ASTM A276 Type 3163. Ball ASTM A276 Type 316 or A351 CF8M4. Stem ASTM A276 Type 3165. Packing Gland ASTM A276 Type 3166. Stem Seals PTFE7. Seats RPTFE8. Gland Screws ASTM A193 B8 Class 19. Gland Plate 316 SS

10. Adapter Screw 18-8 SS11. Handle Adapter 316 SS12. Stem Bearing RPTFE13. Stop ASTM A276 Type 31614. Stop Screw 316 SS15. Lock Plate 302 or 304 SS16. Body Seal RPTFE17. Grounding Spring SS18. Body Joint Stud ASTM A193 Grade B8M19. Body Joint Nut ASTM A194 Grade 820. Adapter Screw 18-8 SS21. Pipe Handle Galvanized Steel (not shown)









4" through 8"

OPTIONS AVAILABLE:(SUFFIX) OPTION-01- Standard (Locking Kit and Grounded Stem)-14- Side Vented Ball (See Page J-2)-21- UHMWPE Seats-24- Fire Safe (Graphite Packing and Seal)-35- PTFE Seats and Seals-49- Assembled Dry-57- Oxygen Cleaned-60- Grounded Ball and Stem-65- MPTFE Seats and Graphite Packing-67- Cleaned For Industrial Gases-69- Drilled and Tapped Purge Ports with Plugs-70- 4" Extended Bonnet (4" & 6" Valves Only)-73- 316 SS Spiral Wound Gaskets w/PTFE Filler-74- 316 SS Spiral Wound Gaskets w/Graphite Filler-MG- Gear Operator with Standard Handwheel-MH- Gear Operator with Standard Handwheel &


Locking Device

1/00


NUMBER SIZE A B C D E F G H I J K L M WT.87A-903-01 1/2" 6.087A-904-01 3/4" 9.087A-905-01 1" 1.00 6.50 3.82 3.62 6.03 0.47 1.62 2.15 1.392 0.696 0.500 0.287 1/4-20 11.0


1/2" through 1"

OPTIONS AVAILABLE:(SUFFIX) OPTION-01- Standard (Locking Kit and Grounded Stem)-14- Side Vented Ball (See Page J-2)-15- Wheel Handle-21- UHMWPE Seats-24- Fire Safe (Graphite Packing and Seal)-35- PTFE Seats and Seals-38- PEEK Seats and Graphite Packing-49- Assembled Dry-57- Oxygen Cleaned-60- Grounded Ball and Stem-65- MPTFE Seats and Graphite Packing-67- Cleaned For Industrial Gases-69- Drilled and Tapped Purge Port with Plugs-70- 4" Extended Bonnet-73- 316 SS Spiral Wound Gaskets w/PTFE Filler-74- 316 SS Spiral Wound Gaskets w/Graphite Filler


10. Stem Nut 316 SS11. Lever 302 or 304 with Vinyl Grip12. Stem Bearing RPTFE13. Stop ASTM A276 Type 31614. Stop Screw 18-8 SS15. Lock Plate 302 or 304 SS16. Body Seal RPTFE17. Lockwasher 302 or 304 SS18. Grounding Spring SS








1/00


NUMBER SIZE A B C D E F G H I J K L M WT.87A-907-01 1-1/2" 1.50 7.50 3.50 4.62 6.65 0.72 2.41 3.09 1.949 0.974 0.625 0.412 5/16-18 21.087A-908-01 2" 2.00 8.50 4.00 5.61 8.40 0.80 3.31 4.08 1.949 0.974 0.750 0.477 5/16-18 37.087A-909-01 2-1/2" 2.50 9.50 4.44 6.23 8.40 0.80 3.93 4.70 1.949 0.974 0.750 0.477 5/16-18 57.0

OPTIONS AVAILABLE:(SUFFIX) OPTION-01- Standard (Locking Kit and Grounded Stem)-14- Side Vented Ball (See Page J-2)-21- UHMWPE Seats-24- Fire Safe (Graphite Packing and Seal)-35- PTFE Seats and Seals-38- PEEK Seats and Graphite Packing (3" Only)-49- Assembled Dry-57- Oxygen Cleaned-60- Grounded Ball and Stem-65- MPTFE Seats and Graphite Packing-67- Cleaned For Industrial Gases-69- Drilled and Tapped Purge Ports with Plugs-70- 4" Extended Bonnet-73- 316 SS Spiral Wound Gaskets w/PTFE Filler-74- 316 SS Spiral Wound Gaskets w/Graphite Filler-MG- Gear Operator with Standard Handwheel-MH- Gear Operator with Standard Handwheel &


Locking Device


10. Stem Nut 18-8 SS11. Lever 316 SS12. Stem Bearing RPTFE13. Stop ASTM A276 Type 31614. Stop Screw 316 SS15. Lock Plate 302 or 304 SS16. Body Seal RPTFE17. Grounding Spring SS18. Body Joint Stud ASTM A193 Grade B8M19. Body Joint Nut ASTM A194 Grade 820. Lockwasher 302 or 304 SS









1-1/2" through 2-1/2"

1/00




3" through 6"

OPTIONS AVAILABLE:(SUFFIX) OPTION-01- Standard (Locking Kit and Grounded Stem)-14- Side Vented Ball (See Page J-2)-21- UHMWPE Seats-24- Fire Safe (Graphite Packing and Seal)-35- PTFE Seats and Seals-38- PEEK Seats and Graphite Packing (3" Only)-49- Assembled Dry-57- Oxygen Cleaned (SS Valves Only)-60- Grounded Ball and Stem-65- MPTFE Seats and Graphite Packing-67- Cleaned For Industrial Gases-69- Drilled and Tapped Purge Port with Plugs-70- 4" Extended Bonnet (3" 7 4" Valves Only)-73- 316 SS Spiral Wound Gaskets w/PTFE Filler-74- 316 SS Spiral Wound Gaskets w/Graphite Filler-MG- Gear Operator with Standard Handwheel-MH- Gear Operator with Standard Handwheel &


Locking Device


10. Adapter Screw 18-8 SS11. Handle Adapter 316 SS12. Stem Bearing RPTFE13. Stop ASTM A276 Type 31614. Stop Screw 316 SS15. Lock Plate 302 or 304 SS16. Body Seal RPTFE17. Grounding Spring SS18. Body Joint Stud ASTM A193 Grade B8M19. Body Joint Nut ASTM A194 Grade 820. Pipe Handle Galvanized Steel (not shown)








1/00



®

OPTIONS AVAILABLE:(SUFFIX) OPTION-01- Standard (Locking Kit and Grounded Stem)-10- SS Lever and Nut-14- Side Vented Ball (See Page J-2)-15- Wheel Handle-21- UHMWPE Seats-24- Fire Safe (Graphite Packing and Seal)-35- PTFE Seats and Seals-38- PEEK Seats and Graphite Packing-49- Assembled Dry-60- Grounded Ball and Stem-65- MPTFE Seats and Graphite Packing-67- Cleaned For Industrial Gases-69- Drilled and Tapped Purge Port with Plug-70- 4" Extended Bonnet-73- 316 SS Spiral Wound Gaskets w/PTFE Filler-74- 316 SS Spiral Wound Gaskets w/Graphite Filler

MATERIALS OFCONSTRUCTIONDescription Material1. Body ASTM A216 WCB2. Retainer ASTM A108 Type 12153. Ball ASTM A108 Type 12154. Stem ASTM A108 Type 12155. Packing Gland ASTM A108 Type 12156. Stem Seals PTFE7. Seats RPTFE8. Gland Screws ASTM A193 B79. Gland Plate 302 or 304 SS

10. Stem Nut 316 SS11. Lever ASTM A366 Steel with Vinyl Grip12. Stem Bearing RPTFE13. Stop ASTM A108 Type 121514. Stop Screw SAE J429 Grade 215. Lock Plate ASTM A366 Steel16. Body Seal RPTFE17. Lockwasher 302 or 304 SS18. Grounding Spring SS


88A-100 SeriesCarbon Steel ANSI Class 150 Flanged Std. Port Ball Valve -

1-1/2" through 2"STANDARDS COMPLIANCEASME B16.5- "Pipe Flanges and Flanged Fittings"ASME B16.10- "Face to Face Dimensions of Valves"ASME B16.34- "Valves - Flanged, Threaded, and






VARIATIONS AVAILABLE:88A-140 Series (316 SS Ball & Stem)

1/00



®88A-100 SeriesCarbon Steel ANSI Class 150 Flanged Std. Port Ball Valve -

2-1/2" through 3"

OPTIONS AVAILABLE:(SUFFIX) OPTION-01- Standard (Locking Kit and Grounded Stem)-10- SS Lever and Nut-14- Side Vented Ball (See Page J-2)-21- UHMWPE Seats-24- Fire Safe (Graphite Packing and Seal)-35- PTFE Seats and Seals-38- PEEK Seats and Graphite Packing-49- Assembled Dry-59- SS External Trim-60- Grounded Ball and Stem-65- MPTFE Seats and Graphite Packing-67- Cleaned For Industrial Gases-69- Drilled and Tapped Purge Port with Plugs-70- 4" Extended Bonnet-73- 316 SS Spiral Wound Gaskets w/PTFE Filler-74- 316 SS Spiral Wound Gaskets w/Graphite Filler-MG- Gear Operator with Standard Handwheel-MH- Gear Operator with Standard Handwheel &


Locking Device

MATERIALS OFCONSTRUCTIONDescription Material1. Body ASTM A216 WCB2. Retainer ASTM A216 WCB3. Ball ASTM A216 WCB or A216 WCB4. Stem ASTM A108 Type 12155. Packing Gland ASTM A108 Type 12156. Stem Seals PTFE7. Seats RPTFE8. Gland Screws ASTM A193 B79. Gland Plate 302 or 304 SS

10. Stem Nut ASTM A194 Grade 811. Lever ASTM A366 Steel with Vinyl Grip12. Stem Bearing RPTFE13. Stop ASTM A108 Type 121514. Stop Screw SAE J429 Grade 215. Lock Plate ASTM A366 Steel16. Body Seal RPTFE17. Grounding Spring SS18. Body Joint Stud ASTM A193 Grade B719. Body Joint Nut ASTM A194 Grade 2H20. Lockwasher 302 or 304 SS









1/00



®

OPTIONS AVAILABLE:(SUFFIX) OPTION-01- Standard (Locking Kit and Grounded Stem)-14- Side Vented Ball (See Page J-2)-21- UHMWPE Seats-24- Fire Safe (Graphite Packing and Seal)-35- PTFE Seats and Seals-49- Assembled Dry-57- Oxygen Cleaned (SS Valves Only)-59- SS External Trim-60- Grounded Ball and Stem-65- MPTFE Seats and Graphite Packing-67- Cleaned For Industrial Gases-69- Drilled and Tapped Purge Ports with Plugs-70- 4" Extended Bonnet (4" & 6" Valves Only)-73- 316 SS Spiral Wound Gaskets w/PTFE Filler-74- 316 SS Spiral Wound Gaskets w/Graphite Filler-MG- Gear Operator with Standard Handwheel-MH- Gear Operator with Standard Handwheel &


Locking Device

MATERIALS OFCONSTRUCTIONDescription Material1. Body ASTM A216 WCB2. Retainer ASTM A216 WCB3. Ball ASTM A216 WCB or A216 WCB4. Stem ASTM A108 Type 12155. Packing Gland ASTM A108 Type 12156. Stem Seals PTFE7. Seats RPTFE8. Gland Screws ASTM A193 B79. Gland Plate 316 SS

10. Adaptor Screw 316 SS11. Handle Adapter ASTM A366 Steel with Vinyl Grip12. Stem Bearing RPTFE13. Stop ASTM A108 Type 121514. Stop Screw SAE J429 Grade 215. Lock Plate ASTM A366 Steel16. Body Seal RPTFE17. Grounding Spring SS18. Body Joint Stud ASTM A193 Grade B719. Body Joint Nut ASTM A194 Grade 2H20. Adapter Screw 18-8 SS21. Pipe Handle Galvanized Steel (not shown)









4" through 8"


1/00


NUMBER SIZE A B C D E F G H I J K L M WT.88A-203-01 1/2" 0.50 4.25 2.06 3.28 5.14 .30 1.09 1.38 1.002 .501 .376 .250 1/4-20 5.088A-204-01 3/4" 0.75 4.62 2.18 3.89 5.56 .39 1.65 1.96 1.392 .696 .500 .287 1/4-20 6.088A-205-01 1" 1.00 5.00 2.32 3.62 6.03 0.47 1.62 2.15 1.392 0.696 0.500 0.287 1/4-20 7.0

®88A-200 SeriesCarbon Steel ANSI Class 150 Flanged Full Port Ball Valve -

1/2" through 1"












1/00



®

OPTIONS AVAILABLE:(SUFFIX) OPTION-01- Standard (Locking Kit and Grounded Stem)-10- SS Lever and Nut-14- Side Vented Ball (See Page J-2)-15- Wheel Handle-21- UHMWPE Seats-24- Fire Safe (Graphite Packing and Seal)-35- PTFE Seats and Seals-38- PEEK Seats and Graphite Packing-49- Assembled Dry-59- SS External Trim-60- Grounded Ball and Stem-65- MPTFE Seats and Graphite Packing-67- Cleaned For Industrial Gases-69- Drilled and Tapped Purge Ports with Plugs-70- 4" Extended Bonnet (4" & 6" Valves Only)-73- 316 SS Spiral Wound Gaskets w/PTFE Filler-74- 316 SS Spiral Wound Gaskets w/Graphite Filler-MG- Gear Operator with Standard Handwheel-MH- Gear Operator with Standard Handwheel &


Locking Device

MATERIALS OFCONSTRUCTIONDescription Material1. Body ASTM A216 WCB2. Retainer ASTM A216 WCB3. Ball ASTM A216 WCB or A216 WCB4. Stem ASTM A108 Type 12155. Packing Gland ASTM A108 Type 12156. Stem Seals PTFE7. Seats RPTFE8. Gland Screws ASTM A193 B79. Gland Plate 302 & 304 SS

10. Stem Nut ASTM A194 Grade 8l11. Lever ASTM A366 Steel with Vinyl Grip12. Stem Bearing RPTFE13. Stop ASTM A108 Type 121514. Stop Screw SAE J429 Grade 215. Lock Plate ASTM A366 Steel16. Body Seal RPTFE17. Grounding Spring SS18. Body Joint Stud ASTM A193 Grade B719. Body Joint Nut ASTM A194 Grade 2H20. Lockwasher 302 or 304 SS







88A-200 SeriesCarbon Steel ANSI Class 150 Flanged Full Port Ball Valve -

1-1/2" through 2-1/2"


1/00





3" through 6"

OPTIONS AVAILABLE:(SUFFIX) OPTION-01- Standard (Locking Kit and Grounded Stem)-14- Side Vented Ball (See Page J-2)-21- UHMWPE Seats-24- Fire Safe (Graphite Packing and Seal)-35- PTFE Seats and Seals-38- PEEK Seats and Graphite Packing-49- Assembled Dry-59- SS External Trim-60- Grounded Ball and Stem-65- MPTFE Seats and Graphite Packing-67- Cleaned For Industrial Gases-69- Drilled and Tapped Purge Port with Plug-70- 4" Extended Bonnet-73- 316 SS Spiral Wound Gaskets w/PTFE Filler-74- 316 SS Spiral Wound Gaskets w/Graphite Filler-MG- Gear Operator with Standard Handwheel-MH- Gear Operator with Standard Handwheel &


Locking Device

MATERIALS OFCONSTRUCTIONDescription Material1. Body ASTM A216 WCB2. Retainer ASTM A216 WCB3. Ball ASTM A108 Type 1215 or A216 WCB4. Stem ASTM A108 Type 12155. Packing Gland ASTM A108 Type 12156. Stem Seals PTFE7. Seats RPTFE8. Gland Screws ASTM A193 B79. Gland Plate 316 SS

10. Adapter Screw 316 SS11. Handle Adapter ASTM A366 Steel with Vinyl Grip12. Stem Bearing RPTFE13. Stop ASTM A108 Type 121514. Stop Screw SAE J429 Grade 215. Lock Plate ASTM A366 Steel16. Body Seal RPTFE17. Grounding Spring SS18. Body Joint Stud ASTM A193 Grade B719. Body Joint Nut ASTM A194 Grade 2H20. Pipe Handle Galvanized Steel (not shown)









1/00



®

OPTIONS AVAILABLE:(SUFFIX) OPTION-01- Standard (Locking Kit and Grounded Stem)-10- SS Lever and Nut-14- Side Vented Ball (See Page J-2)-15- Wheel Handle-21- UHMWPE Seats-24- Fire Safe (Graphite Packing and Seal)-35- PTFE Seats and Seals-38- PEEK Seats and Graphite Packing-49- Assembled Dry-60- Grounded Ball and Stem-65- MPTFE Seats and Graphite Packing-67- Cleaned For Industrial Gases-69- Drilled and Tapped Purge Ports with Plugs-70- 4" Extended Bonnet-73- 316 SS Spiral Wound Gaskets w/PTFE Filler-74- 316 SS Spiral Wound Gaskets w/Graphite Filler

MATERIALS OFCONSTRUCTIONDescription Material1. Body ASTM A216 WCB2. Retainer ASTM A108 Type 12153. Ball ASTM A108 Type 12154. Stem ASTM A108 Type 12155. Packing Gland ASTM A108 Type 12156. Stem Seals PTFE7. Seats RPTFE8. Gland Screws ASTM A193 B79. Gland Plate 302 & 304 SS










1-1/2" through 2"


1/00



®88A-700 SeriesCarbon Steel ANSI Class 300 Flanged Std. Port Ball Valve -

2-1/2" through 3"

MATERIALS OFCONSTRUCTIONDescription Material1. Body ASTM A216 WCB2. Retainer ASTM A216 WCB3. Ball ASTM A108 Type 1215 or A216 WCB4. Stem ASTM A108 Type 12155. Packing Gland ASTM A108 Type 12156. Stem Seals PTFE7. Seats RPTFE8. Gland Screws ASTM A193 B79. Gland Plate 302 or 304 SS

10. Stem Nut ASTM A194 Grade 811. Lever ASTM A366 Steel with Vinyl Grip12. Stem Bearing RPTFE13. Stop ASTM A108 Type 121514. Stop Screw SAE J429 Grade 215. Lock Plate ASTM A366 Steel16. Body Seal RPTFE17. Grounding Spring SS18. Body Joint Stud ASTM A193 Grade B719. Body Joint Nut ASTM A194 Grade 2H20. Lockwasher 302 or 304 SS









1/00

OPTIONS AVAILABLE:(SUFFIX) OPTION-01- Standard (Locking Kit and Grounded Stem)-10- SS Lever and Nut-14- Side Vented Ball (See Page J-2)-15- Wheel Handle-21- UHMWPE Seats-24- Fire Safe (Graphite Packing and Seal)-35- PTFE Seats and Seals-38- PEEK Seats and Graphite Packing-49- Assembled Dry-59- SS External Trim-60- Grounded Ball and Stem-65- MPTFE Seats and Graphite Packing-67- Cleaned For Industrial Gases-69- Drilled and Tapped Purge Port with Plug-70- 4" Extended Bonnet-73- 316 SS Spiral Wound Gaskets w/PTFE Filler-74- 316 SS Spiral Wound Gaskets w/Graphite Filler-MG- Gear Operator with Standard Handwheel-MH- Gear Operator with Standard Handwheel &


Locking Device



®

OPTIONS AVAILABLE:(SUFFIX) OPTION-01- Standard (Locking Kit and Grounded Stem)-14- Side Vented Ball (See Page J-2)-21- UHMWPE Seats-24- Fire Safe (Graphite Packing and Seal)-35- PTFE Seats and Seals-49- Assembled Dry-59- SS External Trim-60- Grounded Ball and Stem-65- MPTFE Seats and Graphite Packing-67- Cleaned For Industrial Gases-69- Drilled and Tapped Purge Ports with Plugs-70- 4" Extended Bonnet (4" & 6" Valves Only)-73- 316 SS Spiral Wound Gaskets w/PTFE Filler-74- 316 SS Spiral Wound Gaskets w/Graphite Filler-MG- Gear Operator with Standard Handwheel-MH- Gear Operator with Standard Handwheel &


Locking Device

MATERIALS OFCONSTRUCTIONDescription Material1. Body ASTM A216 WCB2. Retainer ASTM A216 WCB3. Ball ASTM A108 Type 1215 or A216 WCB4. Stem ASTM A108 Type 12155. Packing Gland ASTM A108 Type 12156. Stem Seals PTFE7. Seats RPTFE8. Gland Screws ASTM A193 B79. Gland Plate 316 SS










4" through 8"


1/00


NUMBER SIZE A B C D E F G H I J K L M WT.88A-903-01 1/2" 7.088A-904-01 3/4" 9.088A-905-01 1" 1.00 6.50 3.82 3.62 6.03 0.47 1.62 2.15 1.392 0.696 0.500 0.287 1/4-20 10.5


1/2" through 1"












1/00



®

MATERIALS OFCONSTRUCTIONDescription Material1. Body ASTM A216 WCB2. Retainer ASTM A216 WCB3. Ball ASTM A216 WCB or A216 WCB4. Stem ASTM A108 Type 12155. Packing Gland ASTM A108 Type 12156. Stem Seals PTFE7. Seats RPTFE8. Gland Screws ASTM A193 B79. Gland Plate 302 & 304 SS

10. Stem Nut ASTM A194 Grade 8l11. Lever ASTM A366 Steel with Vinyl Grip12. Stem Bearing RPTFE13. Stop ASTM A108 Type 121514. Stop Screw SAE J429 Grade 215. Lock Plate ASTM A366 Steel16. Body Seal RPTFE17. Grounding Spring SS18. Body Joint Stud ASTM A193 Grade B719. Body Joint Nut ASTM A194 Grade 2H20. Lockwasher 302 or 304 SS









1-1/2" through 2-1/2"


1/00

OPTIONS AVAILABLE:(SUFFIX) OPTION-01- Standard (Locking Kit and Grounded Stem)-14- Side Vented Ball (See Page J-2)-15- Wheel Handle-21- UHMWPE Seats-24- Fire Safe (Graphite Packing and Seal)-35- PTFE Seats and Seals-38- PEEK Seats and Graphite Packing-49- Assembled Dry-59- SS External Trim-60- Grounded Ball and Stem-65- MPTFE Seats and Graphite Packing-67- Cleaned For Industrial Gases-69- Drilled and Tapped Purge Ports with Plugs-70- 4" Extended Bonnet-73- 316 SS Spiral Wound Gaskets w/PTFE Filler-74- 316 SS Spiral Wound Gaskets w/Graphite Filler-MG- Gear Operator with Standard Handwheel-MH- Gear Operator with Standard Handwheel &


Locking Device



®

OPTIONS AVAILABLE:(SUFFIX) OPTION-01- Standard (Locking Kit and Grounded Stem)-14- Side Vented Ball (See Page J-2)-21- UHMWPE Seats-24- Fire Safe (Graphite Packing and Seal)-35- PTFE Seats and Seals-38- PEEK Seats and Graphite Packing-49- Assembled Dry-59- SS External Trim-60- Grounded Ball and Stem-65- MPTFE Seats and Graphite Packing-67- Cleaned For Industrial Gases-69- Drilled and Tapped Purge Ports with Plugs-70- 4" Extended Bonnet-73- 316 SS Spiral Wound Gaskets w/PTFE Filler-74- 316 SS Spiral Wound Gaskets w/Graphite Filler-MG- Gear Operator with Standard Handwheel-MH- Gear Operator with Standard Handwheel &


Locking Device

MATERIALS OFCONSTRUCTIONDescription Material1. Body ASTM A216 WCB2. Retainer ASTM A216 WCB3. Ball ASTM A216 WCB or A216 WCB4. Stem ASTM A108 Type 12155. Packing Gland ASTM A108 Type 12156. Stem Seals PTFE7. Seats RPTFE8. Gland Screws ASTM A193 B79. Gland Plate 316 SS










3" through 6"

1/00


® 87-100 SeriesStainless Steel ANSI Class 150 Flanged Ball Valve

ANSI Class 150 Flanged Ends, 275 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: SS, Style: 3.

FEATURES (1/2" to 1")• Investment cast body • Meets NACE MR-01-75 • Blow-out-proof stem design• Adjustable packing gland • Unibody construction • Field repairable• RPTFE seats and seals • Corrosion resistant • Positive shut-off• Actuator mounting provisions• (-24) Certified to API standard 607, 4th Edition

STANDARD MATERIAL LIST1. Lever and grip 304 SS w/vinyl 7. Packing gland A276-3162. Stem packing RPTFE (1/2" to 1") 8. Stem A276-3163. Stem bearing RPTFE 9. Lever nut 304 SS4. Ball A276-316 10. Body A351-CF8M5. Seat (2) RPTFE 11. Body seal PTFE6. Retainer A276-316 or A351-CF8M

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/2" to 1"-03- 1-1/4" Stem Extension 1/2" to 1"-04- 2-1/4" Stem Extension 1/2" to 1"-08- 90º Reversed Stem 1/2" to 1"-14- Vented Ball (see page J-2) 1/2" to 1"-15- Round Handle 1/2" to 1"-18- Plain Yellow Grip 1/2" to 1"-21- UHMWPE Seats (Non-PTFE) 1/2" to 1"-24- Graphite Stem Packing 1/2" to 1"-27- Latch Lock Lever 1/2" to 1"-35- PTFE Trim 1/2" to 1"-47- SS Oval Latch-Lock Handle 1/2" to 1"-48- SS Oval Handle 1/2" to 1"-49- Assembled Dry 1/2" to 1"-57- Cleaned For Gaseous Oxygen 1/2" to 1"-60- Static Grounded Ball & Stem 1/2" to 1"-65- Multifill Seats & Graphite Packing 1/2" to 1"

NUMBER SIZE A B C D E F G H I J K Wt.87-103-01 1/2" .50 .62 4.25 1.87 2.37 4.37 2.56 4 3.50 1.38 .43 3.287-104-01 3/4" .62 .62 4.62 1.91 2.75 4.87 2.93 4 3.88 1.69 .50 4.687-105-01 1" .87 .62 5.00 1.94 3.12 4.87 3.12 4 4.25 2.00 .50 6.1

SS ANSI CLASS 150FLANGED BALL VALVE (1/2" to 1")

Contact factory for actuatormounting dimensions. For Pressure/Temperature Ratings,





FEATURES (1-1/2" to 2-1/2")• Investment cast body • Meets NACE MR-01-75 • Blow-out-proof stem design• Adjustable packing gland • Unibody construction • Field repairable• RPTFE seats and seals • Corrosion resistant • Positive shut-off• Actuator mounting provisions• (-24) Certified to API standard 607, 4th Edition

STANDARD MATERIAL LIST1. Lever and grip 304 SS w/vinyl 8. Stem A276-3162. Stem packing PTFE (1-1/2" to 2-1/2") 9. Lever nut 304 SS3. Stem bearing RPTFE 10. Body A351-CF8M4. Ball A276-316 11. Body seal PTFE5. Seat (2) RPTFE 12. Gland plate 304 SS6. Retainer A276-316 or A351-CF8M 13. Gland plate screw ASTM A193 Gr. B87. Packing gland A276-316 14. Stop 304 SS

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1-1/2" to 2-1/2"-03- 1-1/4" Stem Extension 1-1/2" to 2-1/2"-04- 2-1/4" Stem Extension 1-1/2" to 2-1/2"-08- 90º Reversed Stem 1-1/2" to 2-1/2"-14- Vented Ball (see page J-2) 1-1/2" to 2-1/2"-15- Round Handle 1-1/2" to 2-1/2"-18- Plain Yellow Grip 1-1/2" to 2-1/2"-19- Lock Plate 1-1/2" to 2-1/2"-21- UHMWPE Seats (Non-PTFE) 1-1/2" to 2-1/2"-24- Graphite Stem Packing 1-1/2" to 2-1/2"-35- PTFE Trim 1-1/2" to 2-1/2"-49- Assembled Dry 1-1/2" to 2-1/2"-57- Cleaned For Gaseous Oxygen 1-1/2" to 2-1/2"-60- Static Grounded Ball & Stem 1-1/2" to 2-1/2"-65- Multifill Seats & Graphite Packing 1-1/2" to 2-1/2"-69- Purge Ports 2-1/2"-MG- Gear Operator & Hand Wheel 1-1/2" to 2-1/2"

NUMBER SIZE A B C D E F G H I J K Wt.87-107-01 1-1/2" 1.25 .62 6.50 2.25 3.87 8.00 3.81 4 5.00 2.87 .62 12.087-108-01 2" 1.50 .75 7.00 2.54 4.75 8.00 4.12 4 6.00 3.62 .62 17.387-109-01 2-1/2" 2.00 .75 7.50 2.63 5.50 8.00 4.84 4 7.00 4.12 .81 28.0

SS ANSI CLASS 150FLANGED BALL VALVE (1-1/2" to 2-1/2")

Contact factory for actuatormounting dimensions.





FEATURES (3" to 10")• Graphite stem packing • Meets NACE MR-01-75 • Blow-out-proof stem design• Adjustable packing gland • Unibody construction • Field repairable• RPTFE seats and seals • Corrosion resistant • Positive shut-off• Actuator mounting provisions• Certified to API standard 607, 4th Edition

STANDARD MATERIAL LIST1. Handle Galvanized pipe 9. Hex cap screw 18-8 SS2. Stem packing Graphite 10. Body A351-CF8M3. Stem bearing RPTFE 11. Body seal RPTFE4. Ball* A351-CF8M 12. Gland plate 304 SS5. Seat (2) RPTFE 13. Gland plate screw 18-8 SS6. Retainer A351-CF8M 14. Stop A276-3167. Packing gland A276-316 15. Handle adapter A351-CF8M8. Stem A276-316

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-14- Vented Ball (see page J-2) 3" to 10"-19- Lock Plate 3" to 10"-21- UHMWPE Seats (Non-PTFE) 3" to 10"-35- PTFE Trim 3" to 10"-49- Assembled Dry 3" to 10"-57- Cleaned For Gaseous Oxygen 3" to 10"-60- Static Grounded Ball & Stem 3" to 10"-65- Multifill Seats & Graphite Packing 3" to 10"-68- 4" Stem Extension 3" to 6"-69- Purge Ports 3" to 10"-MG- Gear Operator & Hand Wheel 3" to 10"

NUMBER SIZE A B C D E F G H I J K L Wt.87-100-01 3" 2.50 .75 8.00 2.56 6.00 18.00 5.12 6.38 4 5.00 7.50 .75 35.887-10A-01 4" 3.25 .75 9.00 3.22 7.50 18.00 6.22 7.38 8 6.18 9.00 .93 55.087-10C-01 6" 4.50 .87 10.50 4.12 9.50 18.00 7.09 8.25 8 8.50 11.00 1.00 104.087-10E-01 8" 6.00 .87 11.50 5.75 11.75 18.00 9.31 10.43 8 10.62 13.50 1.18 185.087-10G-01 10" 7.50 1.00 13.00 6.50 14.25 30.00 10.50 11.87 12 12.75 16.00 1.31 280.0

SS ANSI CLASS 150FLANGED BALL VALVE (3" to 10")



* Hollow balls are standard on 8” and 10” valves


® 87-200 SeriesStainless Steel ANSI Class 150 Flanged Full Port Ball Valve


FEATURES (1")• Investment cast body • Meets NACE MR-01-75 • Blow-out-proof stem design• Adjustable packing gland • Positive shut-off • Field repairable• RPTFE seats and seals • Corrosion resistant • Unibody design• Certified to API standard 607, 4th Edition, • Actuator mounting provisions

when (-24) ordered

STANDARD MATERIAL LIST1. Lever and grip 304 SS w/vinyl 7. Packing gland A276-3162. Stem packing RPTFE 8. Stem A276-3163. Stem bearing RPTFE 9. Lever nut 18-8 SS4. Ball A276-316 10. Body A351-CF8M5. Seat (2) RPTFE 11. Body seal RPTFE6. Retainer A276-316

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1"-03- 1-1/4" Stem Extension 1"-04- 2-1/4" Stem Extension 1"-08- 90º Reversed Stem 1"-14- Vented Ball (see page J-2) 1"-15- Round Handle 1"-18- Plain Yellow Grip 1"-24- Graphite Stem Packing 1"-27- Latch Lock Lever 1"-35- PTFE Trim 1"-39- SS Hi-Rise Locking Wheel Handle 1"-49- Assembled Dry 1"-57- Cleaned For Gaseous Oxygen 1"-60- Static Grounded Ball & Stem 1"-65- Multifill Seats & Graphite Packing 1"

NUMBER SIZE A B C D E F G H I J K Wt.87-205-01 1" 1.00 .62 5.00 1.94 3.12 8.00 3.62 4 4.25 2.00 .50 7.40

SS ANSI CLASS 150 FULL PORTFLANGED BALL VALVE (1")






FEATURES (1-1/2" to 2-1/2")• Investment cast body • Meets NACE MR-01-75 • Blow-out-proof stem design• Adjustable packing gland • Positive shut-off • Field repairable• RPTFE seats and seals • Corrosion resistant • Bolted body design• Certified to API standard 607, 4th Edition, • Actuator mounting provisions

when (-24) ordered

STANDARD MATERIAL LIST1. Lever and grip 304 SS w/vinyl 9. Lever nut 18-8 SS2. Stem packing PTFE 10. Body A351-CF8M3. Stem bearing RPTFE 11. Body seal Graphite4. Ball A276-316 12. Gland plate 304 SS5. Seat (2) RPTFE 13. Body bolt A193-Grade B86. Retainer A351-CF8M 14. Body nut A193-Grade 87. Packing gland A276-316 15. Gland screws A193-Grade B8, 3048. Stem A276-316 16. Stop 304 SS


SS ANSI CLASS 150 FULL PORTFLANGED BALL VALVE (1-1/2" to 2-1/2")



OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1-1/2" to 2-1/2"-03- 1-1/4" Stem Extension 1-1/2" to 2-1/2"-04- 2-1/4" Stem Extension 1-1/2" to 2-1/2"-08- 90º Reversed Stem 1-1/2" to 2-1/2"-14- Vented Ball (see page J-2) 1-1/2" to 2-1/2"-15- Round Handle 1-1/2" to 2-1/2"-18- Plain Yellow Grip 1-1/2" to 2-1/2"-19- Lock Plate 1-1/2" to 2-1/2"-24- Graphite Stem Packing 1-1/2" to 2-1/2"-35- PTFE Trim 1-1/2" to 2-1/2"-49- Assembled Dry 1-1/2" to 2-1/2"-57- Cleaned For Gaseous Oxygen 1-1/2" to 2-1/2"-60- Static Grounded Ball & Stem 1-1/2" to 2-1/2"-65- Multifill Seats & Graphite Packing 1-1/2" to 2-1/2"-69- Purge Ports 2" to 2-1/2"-MG- Gear Operator & Hand Wheel 1-1/2" to 2-1/2"




FEATURES (3" to 6")• Graphite stem packing • Meets NACE MR-01-75 • Blow-out-proof stem design• Adjustable packing gland • Bolted body design • Field repairable• RPTFE seats • Corrosion resistant • Positive shut-off• Certified to API standard 607, 4th Edition • Actuator mounting provisions

STANDARD MATERIAL LIST1. Handle Galvanized pipe 10. Body A351-CF8M2. Stem packing Graphite 11. Body seal Graphite3. Stem bearing RPTFE 12. Gland plate 304 SS4. Ball A351-CF8M 13. Screw 18-8 SS5. Seat (2) RPTFE 14. Stop A276-3166. Retainer A351-CF8M 15. Handle adapter A351-CF8M7. Packing gland A276-316 16. Body bolt A193 Grade B88. Stem A276-316 17. Body nut A194 Grade 89. Screw 18-8 SS

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-14- Vented Ball (see page J-2) 3" to 6"-19- Lock Plate 3" to 6"-35- PTFE Trim 3" to 6"-49- Assembled Dry 3" to 6"-57- Cleaned For Gaseous Oxygen 3" to 6"-60- Static Grounded Ball & Stem 3" to 6"-65- Multifill Seats & Graphite Packing 3" to 6"-68- 4" Stem Extension 3" to 4"-69- Purge Ports 3" to 6"-MG- Gear Operator & Hand Wheel 3" to 6"

NUMBER SIZE A B C D E F G H I J K L Wt.87-200-01 3" 3.00 .75 8.00 4.00 6.00 18.00 6.00 7.25 4 5.00 7.50 .75 58.387-20A-01 4" 4.00 .75 9.00 5.25 7.50 18.00 7.62 8.87 8 6.18 9.00 .93 98.087-20C-01 6" 6.00 .87 15.50 7.75 9.50 18.00 8.62 9.87 8 8.50 11.00 1.00 212.0

SS ANSI CLASS 150 FULL PORTFLANGED BALL VALVE (3" to 6")







STANDARD MATERIAL LIST1. Stem packing Graphite 8 .Body A351-CF8M2. Stem bearing RPTFE 9 .Body seal Graphite3. Ball* A351-CF8M 10. Gland plate 304 SS4. Seat (2) RPTFE 11. Screw 18-8 SS5. Retainer A351-CF8M 12. Body bolt A193 Grade B86. Packing gland A276-316 13. Body nut A194 Grade 87. Stem A276-316 14. Gear operator Standard

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-14- Vented Ball (see page J-2) 8" to 12"-35- PTFE Trim 8" to 12"-49- Assembled Dry 8" to 12"-57- Cleaned For Gaseous Oxygen 8" to 12"-60- Static Grounded Ball & Stem 8" to 12"-65- Multifill Seats & Graphite Packing 8" to 12"-69- Purge Ports 8" to 12"

NUMBER SIZE A B C D E F G H I J K L Wt.87-20E-01 8" 8.00 .87 18.00 9.00 11.75 18.00 13.59 11.12 8 10.62 13.50 1.18 385.587-20G-01 10" 10.00 1.00 21.00 10.50 14.25 24.00 15.57 17.37 12 12.75 16.00 1.31 607.087-20H-01 12" 12.00 1.00 24.00 12.00 17.00 24.00 17.07 17.37 12 15.00 19.00 1.43 885.5

SS ANSI CLASS 150 FULL PORTFLANGED BALL VALVE (8" to 12")


* Hollow balls are standard.





FEATURES (2")• Graphite stem packing • Meets NACE MR-01-75 • Blow-out-proof stem design• Adjustable packing gland • Unibody construction • Field repairable• RPTFE seats and seals • Corrosion resistant • Positive shut-off• Certified to API standard 607, 4th Edition • Actuator mounting provisions

STANDARD MATERIAL LIST1. Lever and grip 304 SS w/vinyl 8. Stem A276-3162. Stem packing Graphite 9. Lever nut 304 SS3. Stem bearing RPTFE 10. Body A351-CF8M4. Ball A276-316 11. Body seal PTFE5. Seat (2) RPTFE 12. Packing gland A276-3166. Retainer A276-316 13. Stop 304 SS7. Gland plate 304 SS 14. Screw (2) A193-Grade B8

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-03- 1-1/4" Stem Extension 2"-04- 2-1/4" Stem Extension 2"-08- 90º Reversed Stem 2"-14- Vented Ball (see page J-2) 2"-15- Round Handle 2"-18- Plain Yellow Grip 2"-19- Lock Plate 2"-35- PTFE Trim 2"-49- Assembled Dry 2"-57- Cleaned For Gaseous Oxygen 2"-60- Static Grounded Ball & Stem 2"-65- Multifill Seats & Graphite Packing 2"-MG- Gear Operator & Hand Wheel 2"


SS ANSI CLASS 300FLANGED BALL VALVE (2")



D-32




FEATURES (3" to 10")• Graphite stem packing • Meets NACE MR-01-75 • Blow-out-proof stem design• Adjustable packing gland • Unibody construction • Field repairable• RPTFE seats and seals • Corrosion resistant • Positive shut-off• Certified to API standard 607, 4th Edition • Actuator mounting provisions

STANDARD MATERIAL LIST1. Handle Galvanized pipe 9. Screw (2) 18-8 SS2. Stem packing Graphite 10. Body A351-CF8M 3. Stem bearing RPTFE 11. Body seal RPTFE4. Ball* A351-CF8M 12. Gland plate 304 SS5. Seat (2) RPTFE 13. Screw (2) 18-8 SS6. Retainer A351-CF8M 14. Stop A276-3167. Packing gland A276-316 15. Handle adapter A351-CF8M 8. Stem A276-316



NUMBER SIZE A B C D E F G H I J K L Wt.87-700-01 3" 2.50 .87 11.12 3.00 6.62 18.00 5.50 6.75 8 5.00 8.25 1.12 56.087-70A-01 4" 3.25 .87 12.00 3.43 7.87 18.00 7.00 8.25 8 6.18 10.00 1.25 89.087-70C-01 6" 4.50 .87 15.87 6.62 10.62 18.00 7.87 9.12 12 8.50 12.50 1.43 179.087-70E-01 8" 6.00 1.00 16.50 5.75 13.00 18.00 10.25 11.50 12 10.62 15.00 1.75 265.087-70G-01 10" 7.50 1.25 18.00 6.50 15.25 18.00 11.50 12.75 16 12.75 17.50 1.88 401.0





® 87-808 SeriesStainless Steel 2" ANSI Class 600 Flanged Ball Valve

ANSI Class 600 Flanged Ends, 1440 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.On-Off Service.Federal Specification: WW-V-35C

FEATURES• Investment cast body • Unibody design • Blow-out-proof stem design• Adjustable packing gland • Positive shut-off • Meets NACE MR-01-75• RPTFE seats and seals • Corrosion resistant• Certified to API standard 607, 3rd Edition,

when (-24) ordered

STANDARD MATERIAL LIST1. Lever and grip 304 SS w/vinyl 7. Stem A276-3162. Stem packing RPTFE 8. Lever nut 18-8 SS 3. Stem bearing RPTFE 9. Lever washer 304 SS4. Ball A276-316 10. Body seal PTFE5. Seat (2) RPTFE 11. Gland screw A276-3166. Retainer A276-316 12. Body A351-CF8M

NUMBER SIZE A B C D E F G H I J K Wt.87-808-01 2" 1.50 .75 11.50 3.50 5.00 9.75 4.37 8 6.50 3.62 1.06 29.0

SS 2" ANSI CLASS 600FLANGED BALL VALVE



® 88-808 SeriesCarbon Steel 2" ANSI Class 600 Flanged Ball Valve

ANSI Class 600 Flanged Ends, 1480 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.On-Off Service.Federal Specification: WW-V-35C

FEATURES• Investment cast body • Positive shut-off • Blow-out-proof stem design• Adjustable packing gland • Unibody design • Corrosion resistant• RPTFE seats and seals • Nitride corrosion protection• Certified to API standard 607, 3rd Edition, when (-24) ordered

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 7. Stem A108-12L14, chrome plated2. Stem packing RPTFE 8. Lever nut Steel, zinc plated 3. Stem bearing RPTFE 9. Body seal PTFE4. Ball A108-CS, chrome plated 10. Gland screw A108-CS5. Seat (2) RPTFE 11. Body A216-WCB6. Retainer A108-CS

VARIATIONS AVAILABLE:88-848-01 Series (316 SS Ball & Stem)

NUMBER SIZE A B C D E F G H I J K Wt.88-808-01 2" 1.50 .75 11.50 3.50 5.00 9.75 4.37 8 6.50 3.62 1.06 29.0

CARBON STEEL 2" ANSI CLASS 600FLANGED BALL VALVE





FEATURES (1/2" to 1-1/2")• Investment cast body • Meets NACE MR-01-75 • Blow-out-proof stem design• Adjustable packing gland • Positive shut-off • Field repairable• RPTFE seats • Corrosion resistant • Unibody design• Certified to API standard 607, 4th Edition, • Actuator mounting provisions

when (-24) ordered

STANDARD MATERIAL LIST1. Lever and grip 304 SS w/vinyl 7. Packing gland A276-3162. Stem packing PTFE 8. Stem A276-3163. Stem bearing RPTFE 9. Lever nut 18-8 SS4. Ball A276-316 10. Body A351-CF8M5. Seat (2) RPTFE 11. Body seal RPTFE6. Retainer A351-CF8M

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/2" to 1-1/2"-03- 1-1/4" Stem Extension 1/2" to 1-1/2"-04- 2-1/4" Stem Extension 1/2" to 1-1/2"-08- 90º Reversed Stem 1/2" to 1-1/2"-14- Vented Ball (see page J-2) 1/2" to 1-1/2"-15- Round Handle 1/2" to 1-1/2"-18- Plain Yellow Grip 1/2" to 1-1/2"-24- Graphite Stem Packing 1/2" to 1-1/2"-27- Latch Lock Lever 1/2" to 1-1/2"-35- PTFE Trim 1/2" to 1-1/2"-47- SS Oval Latch-Lock Handle 1/2" to 1"-48- SS Oval Handle 1/2" to 1"-49- Assembled Dry 1/2" to 1-1/2"-57- Cleaned For Gaseous Oxygen 1/2" to 1-1/2"-60- Static Grounded Ball & Stem 1/2" to 1-1/2"-65- Multifill Seats & Graphite Packing 1/2" to 1-1/2"

NUMBER SIZE A B C D E F G H I J K Wt.87-903-01 1/2" .62 .62 5.50 1.98 2.62 4.78 2.93 4 3.75 1.37 .56 6.087-904-01 3/4" .81 .75 6.00 2.35 3.25 4.78 3.10 4 4.62 1.68 .61 9.087-905-01 1" 1.00 .75 6.50 2.45 3.50 7.93 3.62 4 4.88 2.00 .68 12.087-907-01 1-1/2" 1.50 .88 7.50 3.25 4.50 8.00 4.60 4 6.12 2.87 .82 23.0

SS ANSI CLASS 300 FULL PORTFLANGED BALL VALVE (1/2" to 1-1/2")






FEATURES (2")• Investment cast body • Meets NACE MR-01-75 • Blow-out-proof stem design• Adjustable packing gland • Positive shut-off • Field repairable• RPTFE seats • Corrosion resistant • Bolted body design• Certified to API standard 607, 4th Edition, • Actuator mounting provisions

when (-24) ordered

STANDARD MATERIAL LIST1. Lever and grip 304 SS w/vinyl 9. Lever nut 18-8 SS2. Stem packing PTFE 10. Body A351-CF8M3. Stem bearing RPTFE 11. Body seal Graphite4. Ball A276-316 12. Gland plate 304 SS5. Seat (2) RPTFE 13. Body bolt A193-Grade B86. Retainer A351-CF8M 14. Body nut A193-Grade 87. Packing gland A276-316 15. Gland screws A193-Grade B8, 3048. Stem A276-316 16. Stop 304 SS





OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 2"-03- 1-1/4" Stem Extension 2"-04- 2-1/4" Stem Extension 2"-08- 90º Reversed Stem 2"-14- Vented Ball (see page J-2) 2"-15- Round Handle 2"-18- Plain Yellow Grip 2"-19- Lock Plate 2"-24- Graphite Stem Packing 2"-35- PTFE Trim 2"-49- Assembled Dry 2"-57- Cleaned For Gaseous Oxygen 2"-60- Static Grounded Ball & Stem 2"-65- Multifill Seats & Graphite Packing 2"-69- Purge Ports 2"-MG- Gear Operator & Hand Wheel 2"





STANDARD MATERIAL LIST1. Handle Galvanized pipe 10. Body A351-CF8M2. Stem packing Graphite 11. Body seal Graphite3. Stem bearing RPTFE 12. Gland plate 304 SS4. Ball A351-CF8M 13. Screw 18-8 SS5. Seat (2) RPTFE 14. Stop A276-3166. Retainer A351-CF8M 15. Handle adapter A351-CF8M7. Packing gland A276-316 16. Body bolt A193 Grade B88. Stem A276-316 17. Body nut A193 Grade 89. Screw 18-8 SS


NUMBER SIZE A B C D E F G H I J K L Wt.87-900-01 3" 3.00 .87 11.12 5.12 6.62 18.00 6.15 7.33 8 5.00 8.25 1.06 76.087-90A-01 4" 4.00 .87 12.00 6.25 7.87 18.00 7.56 8.81 8 6.18 10.00 1.18 140.087-90C-01 6" 6.00 .87 15.87 8.37 10.62 18.00 10.15 11.33 8 8.50 12.50 1.43 280.0







FEATURES (8")• Graphite stem packing • Meets NACE MR-01-75 • Blow-out-proof stem design• Adjustable packing gland • Bolted body design • Field repairable• RPTFE seats • Corrosion resistant • Positive shut-off• Certified to API standard 607, 4th Edition • Actuator mounting provisions

STANDARD MATERIAL LIST1. Stem packing Graphite 8. Body A351-CF8M2. Stem bearing RPTFE 9. Body seal Graphite3. Ball A351-CF8M 10. Gland plate 304 SS4. Seat (2) RPTFE 11. Screw (2) 18-8 SS5. Retainer A351-CF8M 12. Body bolt A193 Grade B86. Packing gland A276-316 13. Body nut A193 Grade 87. Stem A276-316 14. Gear operator Standard


NUMBER SIZE A B C D E F G H I J K L Wt.87-90E-01 8" 8.00 1.00 16.50 8.25 13.00 18.00 14.48 11.12 12 10.62 15.00 1.68 485.0



OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-14- Vented Ball (see page J-2) 8"-35- PTFE Trim 8"-49- Assembled Dry 8"-57- Cleaned For Gaseous Oxygen 8"-60- Static Grounded Ball & Stem 8"-65- Multifill Seats & Graphite Packing 8"-69- Purge Ports 8"


® 88-100 SeriesCarbon Steel ANSI Class 150 Flanged Ball Valve

ANSI Class 150 Flanged Ends, 285 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: CS, Style: 3.

FEATURES (1/2" to 1")• Investment cast body • Positive shut-off • Blow-out-proof stem design• Adjustable packing gland • Unibody construction • Field repairable• RPTFE seats and seals • Corrosion resistant • Nitride corrosion protection• (-24) Certified to API standard 607, 4th Edition • Actuator mounting provisions

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 7. Packing gland A108-CS 2. Stem packing RPTFE 8. Stem A108-CS3. Stem bearing RPTFE 9. Lever nut Steel, zinc plated4. Ball A108-CS chrome plated 10. Body A216-WCB5. Seat (2) RPTFE 11. Body seal PTFE6. Retainer A108-CS


OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/2" to 1"-03- 1-1/4" Stem Extension 1/2" to 1"-04- 2-1/4" Stem Extension 1/2" to 1"-08- 90º Reversed Stem 1/2" to 1"-10- SS Lever & Nut 1/2" to 1"-14- Vented Ball (see page J-2) 1/2" to 1"-15- Round Handle 1/2" to 1"-18- Plain Yellow Grip 1/2" to 1"-21- UHMWPE Seats (Non-PTFE) 1/2" to 1"-24- Graphite Stem Packing 1/2" to 1"-35- PTFE Trim 1/2" to 1"-47- SS Oval Latch-Lock Handle 1/2" to 1"-48- SS Oval Handle 1/2" to 1"-65- Multifill Seats & Graphite Packing 1/2" to 1"-67- Cleaned For Industrial Gases 1/2" to 1"

NUMBER SIZE A B C D E F G H I J K Wt.88-103-01 1/2" .50 .62 4.25 1.87 2.37 4.37 2.56 4 3.50 1.38 .43 3.288-104-01 3/4" .62 .62 4.62 1.91 2.75 4.87 2.93 4 3.88 1.69 .50 4.588-105-01 1" .87 .62 5.00 1.94 3.12 4.87 3.12 4 4.25 2.00 .50 6.1

CARBON STEEL ANSI CLASS 150FLANGED BALL VALVE (1/2" to 1")






FEATURES (1-1/2" to 2-1/2")• Investment cast body • Positive shut-off • Blow-out-proof stem design• Adjustable packing gland • Unibody construction • Field repairable• RPTFE seats and seals • Corrosion resistant • Nitride corrosion protection• (-24) Certified to API standard 607, 4th Edition • Actuator mounting provisions

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 8. Stem A108-CS 2. Stem packing PTFE 9. Lever nut Steel, zinc plated 3. Stem bearing RPTFE 10. Body A216-WCB4. Ball A108-CS, chrome plated 11. Body seal PTFE5. Seat (2) RPTFE 12. Gland plate CS, zinc plated6. Retainer A108-CS 13. Gland plate screw ASTM A193 Gr. B7, zinc plated7. Packing gland A108-CS 14. Stop CS, zinc plated



CARBON STEEL ANSI CLASS 150FLANGED BALL VALVE (1-1/2" to 2-1/2")



OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1-1/2" to 2-1/2"-03- 1-1/4" Stem Extension 1-1/2" to 2-1/2"-04- 2-1/4" Stem Extension 1-1/2" to 2-1/2"-08- 90º Reversed Stem 1-1/2" to 2-1/2"-10- SS Lever & Nut 1-1/2" to 2-1/2"-14- Vented Ball (see page J-2) 1-1/2" to 2-1/2"-15- Round Handle 1-1/2" to 2-1/2"-18- Plain Yellow Grip 1-1/2" to 2-1/2"-21- UHMWPE Seats (Non-PTFE) 1-1/2" to 2-1/2"-24- Graphite Stem Packing 1-1/2" to 2-1/2"-35- PTFE Trim 1-1/2" to 2-1/2"-65- Multifill Seats & Graphite Packing 1-1/2" to 2-1/2"-67- Cleaned for Industrial Gases 1-1/2" to 2-1/2"-69- Purge Ports 2-1/2"-MG- Gear Operator & Hand Wheel 1-1/2" to 2-1/2"




FEATURES (3" to 10")• Graphite stem packing • Positive shut-off • Blow-out-proof stem design• Adjustable packing gland • Unibody construction • Field repairable• RPTFE seats and seals • Corrosion resistant • Nitride corrosion protection• Actuator mounting provisions • Meets NACE MR-01-75 with SS trim• Certified to API standard 607, 4th Edition

STANDARD MATERIAL LIST1. Handle Galvanized pipe 9. Hex cap screw Steel, grade 82. Stem packing Graphite 10. Body A216-WCB3. Stem bearing RPTFE 11. Body seal RPTFE4. Ball* A216-WCB chrome plated 12. Gland plate 304 SS5. Seat (2) RPTFE 13. Gland plate screw Steel, grade 86. Retainer A216-WCB 14. Stop A276-3167. Packing gland A108-CS 15. Handle adapter A351-CF8M8. Stem A108-CS


OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-14- Vented Ball (see page J-2) 3" to 10"-19- Lock Plate 3" to 10"-21- UHMWPE Seats (Non-PTFE) 3" to 10"-35- PTFE Trim 3" to 10"-65- Multifill Seats & Graphite Packing 3" to 10"-67- Cleaned for Industrial Gases 3" to 10"-68- 4" Stem Extension 3" to 6"-69- Purge Ports 3" to 10"-MG- Gear Operator & Hand Wheel 3" to 10"

NUMBER SIZE A B C D E F G H I J K L Wt.88-100-01 3" 2.50 .75 8.00 2.56 6.00 18.00 5.12 6.38 4 5.00 7.50 .75 35.188-10A-01 4" 3.25 .75 9.00 3.22 7.50 18.00 6.22 7.38 8 6.18 9.00 .93 54.588-10C-01 6" 4.50 .87 10.50 4.12 9.50 18.00 7.09 8.25 8 8.50 11.00 1.00 104.088-10E-01 8" 6.00 .87 11.50 5.75 11.75 18.00 9.31 10.43 8 10.62 13.50 1.18 185.088-10G-01 10" 7.50 1.00 13.00 6.50 14.25 30.00 10.50 11.87 12 12.75 16.00 1.31 280.0

CARBON STEEL ANSI CLASS 150FLANGED BALL VALVE (3" to 10")





® 88-200 SeriesCarbon Steel ANSI Class 150 Flanged Full Port Ball Valve


FEATURES (1")• Investment cast body • Blow-out-proof stem design • Field repairable• Adjustable packing gland • Positive shut-off • Unibody construction• RPTFE seats and seals • Corrosion resistant • Actuator mounting provisions• Certified to API standard 607, 4th Edition when (-24) ordered

STANDARD MATERIAL LIST1. Lever & grip 304 SS 7. Packing gland A108-CS2. Stem packing RPTFE 8. Stem A108-CS3. Stem bearing RPTFE 9. Lever nut 18-8 SS4. Ball A108-CS 10. Body A216-WCB5. Seat (2) RPTFE 11. Body seal RPTFE6. Retainer A108-CS

VARIATIONS AVAILABLE:88-240 series (SS Ball & Stem)

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1"-03- 1-1/4" Stem Extension 1"-04- 2-1/4" Stem Extension 1"-08- 90º Reversed Stem 1"-14- Vented Ball (see page J-2) 1"-15- Round Handle 1"-18- Plain Yellow Grip 1"-24- Graphite Stem Packing 1"-27- Latch Lock Lever 1"-35- PTFE Trim 1"-39- SS Hi-Rise Locking Wheel Handle 1"-49- Assembled Dry 1"-60- Static Grounded Ball & Stem 1"-65- Multifill Seats & Graphite Packing 1"-67- Cleaned for Industrial Gases 1"


CARBON STEEL ANSI CLASS 300 FULL PORTFLANGED BALL VALVE (1")






FEATURES (1-1/2" to 2-1/2")• Investment cast body • Blow-out-proof stem design • Field repairable• Adjustable packing gland • Positive shut-off • Bolted body design• RPTFE seats and seals • Corrosion resistant • Actuator mounting provisions• Certified to API standard 607, 4th Edition, • Nitride corrosion protection

when (-24) ordered • Meets NACE MR-01-75 with SS trim

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 9. Lever nut Steel, grade 8 zinc plated2. Stem packing PTFE 10. Body A216-WCB3. Stem bearing RPTFE 11. Body seal Graphite4. Ball A108-CS chrome plated 12. Gland plate CS, zinc plated5. Seat (2) RPTFE 13. Body bolt A193-Grade B76. Retainer A216-WCB 14. Body nut A194-Grade 2H7. Packing gland A108 CS 15. Gland screws A193-Grade B7 zinc plated8. Stem A108-CS 16. Stop CS, zinc plated

VARIATIONS AVAILABLE:88-240 series (SS Ball & Stem)


CARBON STEEL ANSI CLASS 150 FULL PORTFLANGED BALL VALVE (1-1/2" to 2-1/2")



OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1-1/2" to 2-1/2"-03- 1-1/4" Stem Extension 1-1/2" to 2-1/2"-04- 2-1/4" Stem Extension 1-1/2" to 2-1/2"-08- 90º Reversed Stem 1-1/2" to 2-1/2"-10- SS Lever & Nut 1-1/2" to 2-1/2"-14- Vented Ball (see page J-2) 1-1/2" to 2-1/2"-15- Round Handle 1-1/2" to 2-1/2"-18- Plain Yellow Grip 1-1/2" to 2-1/2"-19- Lock Plate 1-1/2" to 2-1/2"-24- Graphite Stem Packing 1-1/2" to 2-1/2"-35- PTFE Trim 1-1/2" to 2-1/2"-60- Static Grounded Ball & Stem 1-1/2" to 2-1/2"-65- Multifill Seats & Graphite Packing 1-1/2" to 2-1/2"-67- Cleaned For Industrial Gases 1-1/2" to 2-1/2"-69- Purge Ports 2" to 2-1/2"-MG- Gear Operator & Hand Wheel 1-1/2" to 2-1/2"




FEATURES (3" to 6")• Graphite stem packing • Positive shut-off • Blow-out-proof stem design• Adjustable packing gland • Bolted body design • Field repairable• RPTFE seats • Corrosion resistant • Actuator mounting provisions• Certified to API standard 607, 4th Edition • Nitride corrosion protection• Meets NACE MR-01-75 with SS trim

STANDARD MATERIAL LIST1. Handle Galvanized pipe 10. Body A216-WCB2. Stem packing Graphite 11. Body seal Graphite3. Stem bearing RPTFE 12. Gland plate 304 SS4. Ball A216-WCB, chrome plated 13. Screw Steel, grade 8 zinc plated5. Seat (2) RPTFE 14. Stop A276-3166. Retainer A216-WCB 15. Handle adapter A351-CF8M7. Packing gland A108-CS 16. Body bolt A194-Grade B78. Stem A108-CS 17. Body nut A194-Grade 2H9. Screw Steel, grade 8 zinc plated

VARIATIONS AVAILABLE:88-240 Series (SS Ball & Stem)

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-14- Vented Ball (see page J-2) 3" to 6"-19- Lock Plate 3" to 6"-35- PTFE Trim 3" to 6"-60- Static Grounded Ball & Stem 3" to 6"-65- Multifill Seats & Graphite Packing 3" to 6"-67- Cleaned for Industrial Gases 3" to 6"-68- 4" Stem Extension 3" to 4"-69- Purge Ports 3" to 6"-MG- Gear Operator & Hand Wheel 3" to 6"

NUMBER SIZE A B C D E F G H I J K L Wt.88-200-01 3" 3.00 .75 8.00 4.00 6.00 18.00 6.00 7.25 4 5.00 7.50 .75 58.388-20A-01 4" 4.00 .75 9.00 5.25 7.50 18.00 7.62 8.87 8 6.18 9.00 .93 98.088-20C-01 6" 6.00 .87 15.50 7.75 9.50 18.00 8.62 9.87 8 8.50 11.00 1.00 212.0

CARBON STEEL ANSI CLASS 150 FULL PORTFLANGED BALL VALVE (3" to 6") Contact factory for actuator

mounting dimensions.





FEATURES (8" to 12")• Graphite stem packing • Positive shut-off • Blow-out-proof stem design• Adjustable packing gland • Bolted body design • Field repairable• RPTFE seats • Corrosion resistant • Actuator mounting provisions• Certified to API standard 607, 4th Edition • Nitride corrosion protection• Meets NACE MR-01-75 with SS trim

STANDARD MATERIAL LIST1. Stem packing Graphite 8. Body A216-WCB2. Stem bearing RPTFE 9. Body seal Graphite3. Ball A216-WCB, chrome plated 10. Gland plate 304 SS4. Seat (2) RPTFE 11. Screw Steel, grade 8 zinc plated5. Retainer A216-WCB 12. Body bolt A193-Grade B76. Packing gland A108-CS 13. Body nut A193-Grade 2H7. Stem A108-CS 14. Gear operator Standard


NUMBER SIZE A B C D E F G H I J K L Wt.88-20E-01 8" 8.00 .87 18.00 9.00 11.75 18.00 13.59 11.12 8 10.62 13.50 1.18 395.088-20G-01 10" 10.00 1.00 21.00 10.50 14.25 24.00 15.57 17.37 12 12.75 16.00 1.31 607.088-20H-01 12" 12.00 1.00 24.00 12.00 17.00 24.00 17.07 17.37 12 15.00 19.00 1.43 885.0

CARBON STEEL ANSI CLASS 150 FULL PORTFLANGED BALL VALVE (8" to 12")



OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-14- Vented Ball (see page J-2) 8" to 12"-35- PTFE Trim 8" to 12"-60- Static Grounded Ball & Stem 8" to 12"-65- Multifill Seats & Graphite Packing 8" to 12"-67- Cleaned for Industrial Gases 8" to 12"-69- Purge Ports 8" to 12"


®


88-700 SeriesCarbon Steel ANSI Class 300 Flanged Ball Valve


FEATURES (2")• Graphite stem packing • Positive shut-off • Blow-out-proof stem design• Adjustable packing gland • Unibody construction • Field repairable• RPTFE seats and seals • Corrosion resistant • Nitride corrosion protection• Actuator mounting provisions • Certified to API standard 607, 4th Edition

STANDARD MATERIAL LIST1. Lever & grip Steel, zinc coated w/vinyl 8. Stem A108-CS, chrome plated2. Stem packing Graphite 9. Lever nut Steel, grade 8 zinc plated3. Stem bearing RPTFE 10. Body A216-WCB4. Ball A108-CS, chrome plated 11. Body seal PTFE5. Seat (2) RPTFE 12. Packing gland A108-CS6. Retainer A108-CS 13. Stop Steel, zinc plated7. Gland plate Steel, zinc plated 14. Screw (2) A193-Grade B7



CARBON STEEL ANSI CLASS 300FLANGED BALL VALVE (2")


OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-03- 1-1/4" Stem Extension 2"-04- 2-1/4" Stem Extension 2"-08- 90º Reversed Stem 2"-14- Vented Ball (see page J-2) 2"-15- Round Handle 2"-18- Plain Yellow Grip 2"-19- Lock Plate 2"-35- PTFE Trim 2"-60- Static Grounded Ball & Stem 2"-65- Multifill Seats & Graphite Packing 2"-67- Cleaned for Industrial Gases 2"-MG- Gear Operator & Hand Wheel 2"




FEATURES (3" to 10")• Graphite stem packing • Positive shut-off • Blow-out-proof stem design• Adjustable packing gland • Unibody construction • Field repairable• RPTFE seats and seals • Corrosion resistant • Nitride corrosion protection• Actuator mounting provisions • Meets NACE MR-01-75 with SS trim• Certified to API standard 607, 4th Edition

STANDARD MATERIAL LIST1. Handle Galvanized pipe 9. Screw (2) Steel, grade 8 zinc plated2. Stem packing Graphite 10. Body A216-WCB3. Stem bearing RPTFE 11. Body seal RPTFE4. Ball A216-WCB, chrome plated 12. Gland plate 304 SS5. Seat (2) RPTFE 13. Screw (2) Steel, grade 8 zinc plated6. Retainer A216-WCB 14. Stop A276-3167. Packing gland A108-CS 15. Handle adapter A351-CF8M8. Stem A108-CS



NUMBER SIZE A B C D E F G H I J K L Wt.88-700-01 3" 2.50 .87 11.12 3.00 6.62 18.00 5.50 6.75 8 5.00 8.25 1.12 56.088-70A-01 4" 3.25 .87 12.00 3.43 7.87 18.00 7.00 8.25 8 6.18 10.00 1.25 89.088-70C-01 6" 4.50 .87 15.87 6.62 10.62 18.00 7.87 9.12 12 8.50 12.50 1.43 179.088-70E-01 8" 6.00 1.00 16.50 5.75 13.00 18.00 10.25 11.50 12 10.62 15.00 1.75 265.088-70G-01 10" 7.50 1.25 18.00 6.50 15.25 18.00 11.50 12.75 16 12.75 17.50 1.88 401.0

CARBON STEEL ANSI CLASS 300FLANGED BALL VALVE (3" to 10")






FEATURES (1/2" to 1-1/2")• Investment cast body • Blow-out-proof stem design • Field repairable• Adjustable packing gland • Positive shut-off • Unibody design• RPTFE seats and seals • Nitride corrosion protection • Actuator mounting provisions• Certified to API standard 607, 4th Edition, when (-24) ordered

STANDARD MATERIAL LIST1. Lever & grip 304 SS w/vinyl 8. Stem A108-12152. Stem packing PTFE 9. Lever nut 18-8 SS3. Stem bearing RPTFE 10. Body A216-WCB4. Ball A108-CS 11. Body seal RPTFE5. Seat (2) RPTFE6. Retainer A108-12157. Packing gland A108-1215

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 1/2" to 1-1/2"-03- 1-1/4" Stem Extension 1/2" to 1-1/2"-04- 2-1/4" Stem Extension 1/2" to 1-1/2"-08- 90º Reversed Stem 1/2" to 1-1/2"-14- Vented Ball (see page J-2) 1/2" to 1-1/2"-15- Round Handle 1/2" to 1-1/2"-18- Plain Yellow Grip 1/2" to 1-1/2"-24- Graphite Stem Packing 1/2" to 1-1/2"-27- Latch Lock Lever 1/2" to 1-1/2"-35- PTFE Trim 1/2" to 1-1/2"-47- SS Oval Latch-Lock Handle 1/2" to 1-1/2"-48- SS Oval Handle 1/2" to 1-1/2"-49- Assembled Dry 1/2" to 1-1/2"-57- Cleaned for Gaseous Oxygen 1/2" to 1-1/2"-60- Static Grounded Ball & Stem 1/2" to 1-1/2"-65- Multifill Seats & Graphite Packing 1/2" to 1-1/2"-67- Cleaned for Industrial Gases 1/2" to 1-1/2"



NUMBER SIZE A B C D E F G H I J K Wt.88-903-01 1/2" .62 .62 5.50 1.98 2.62 4.78 2.93 4 3.75 1.37 .56 6.088-904-01 3/4" .81 .75 6.00 2.35 3.25 4.78 3.10 4 4.62 1.68 .61 9.088-905-01 1" 1.00 .75 6.50 2.45 3.50 7.93 3.62 4 4.88 2.00 .68 12.088-907-01 1-1/2" 1.50 .88 7.50 3.25 4.50 8.00 4.60 4 6.12 2.87 .82 23.0

CARBON STEEL ANSI CLASS 300 FULL PORTFLANGED BALL VALVE (1/2" to 1-1/2")




ANSI Class 300 Flanged Ends, 740 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: CS Style: 3

FEATURES (2")• Investment cast body • Positive shut-off • Blow-out-proof stem design• Adjustable packing gland • Bolted body design • Field repairable• RPTFE seats and seals • Nitride corrosion protection • Actuator mounting provisions• Certified to API standard 607, 4th Edition, • Meets NACE MR-01-75 with SS trimwhen (-24) ordered

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 9. Lever nut Steel, grade 8 zinc plated2. Stem packing PTFE 10. Body A216-WCB3. Stem bearing RPTFE 11. Body seal Graphite4. Ball A108-CS chrome plated 12. Gland plate Steel, zinc plated5. Seat (2) RPTFE 13. Body bolt A193-Grade B76. Retainer A216-WCB 14. Body nut A194-Grade 2H7. Packing gland A108-1215 15. Gland screws A193-Grade B7 zinc plated8. Stem A108-1215 16. Stop Steel, zinc plated

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02- Static Grounded 2"-03- 1-1/4" Stem Extension 2"-04- 2-1/4" Stem Extension 2"-08- 90º Reversed Stem 2"-10- SS Lever & Nut 2"-14- Vented Ball (see page J-2) 2"-15- Round Handle 2"-18- Plain Yellow Grip 2"-19- Lock Plate 2"-24- Graphite Stem Packing 2"-35- PTFE Trim 2"-60- Static Grounded Ball & Stem 2"-65- Multifill Seats & Graphite Packing 2"-67- Cleaned for Industrial Gases 2"-69- Purge Ports 2"-MG- Gear Operator & Hand Wheel 2"









FEATURES (3" to 6")• Graphite stem packing • Positive shut-off • Blow-out-proof stem design• Adjustable packing gland • Bolted body design • Field repairable• RPTFE seats • Nitride corrosion protection • Actuator mounting provisions• Certified to API standard 607, 4th Edition • Meets NACE MR-01-75 with SS trim

STANDARD MATERIAL LIST1. Handle Galvanized pipe 10. Body A216-WCB2. Stem packing Graphite 11. Body seal Graphite3. Stem bearing RPTFE 12. Gland plate 304 SS4. Ball A216-WCB, chrome plated 13. Screw Steel, grade 8 zinc plated5. Seat (2) RPTFE 14. Stop A276-3166. Retainer A216-WCB 15. Handle adapter A351-CF8M7. Packing gland A108-1215 16. Body bolt A193-Grade B78. Stem A108-1215 17. Body nut A194-Grade 2H9. Screw Steel, grade 8 zinc plated



NUMBER SIZE A B C D E F G H I J K L Wt.88-900-01 3" 3.00 .87 11.12 5.12 6.62 18.00 6.15 7.33 8 5.00 8.25 1.06 76.088-90A-01 4" 4.00 .87 12.00 6.25 7.87 18.00 7.56 8.81 8 6.18 10.00 1.18 140.088-90C-01 6" 6.00 .87 15.87 8.37 10.62 18.00 10.15 11.33 8 8.50 12.50 1.43 280.0

CARBON STEEL ANSI CLASS 300 FULL PORTFLANGED BALL VALVE (3" to 6")






FEATURES (8")• Graphite stem packing • Positive shut-off • Blow-out-proof stem design• Adjustable packing gland • Bolted body design • Field repairable• RPTFE seats • Nitride corrosion protection • Actuator mounting provisions• Certified to API standard 607, 4th Edition • Meets NACE MR-01-75 with SS trim

STANDARD MATERIAL LIST1. Stem packing Graphite 8. Body A216-WCB2. Stem bearing RPTFE 9. Body seal Graphite3. Ball* A216-WCB, chrome plated 10. Gland plate 304 SS4. Seat (2) RPTFE 11. Screw Steel, grade 8 zinc plated5. Retainer A216-WCB 12. Body bolt A193-Grade B76. Packing gland A108-1215 13. Body nut A194-Grade 2H7. Stem A108-1215 14. Gear operator Standard* Hollow ball is standard.


NUMBER SIZE A B C D E F G H I J K L Wt.88-90E-01 8" 8.00 1.00 16.50 8.25 13.00 18.00 14.48 11.12 12 10.62 15.00 1.68 485.0




OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-14- Vented Ball (see page J-2) 8"-35- PTFE Trim 8"-60- Static Grounded Ball & Stem 8"-65- Multifill Seats & Graphite Packing 8"-67- Cleaned for Industrial Gases 8"-69- Purge Ports 8"


® 452-200 SeriesStainless Steel Class 150 Full Port Flanged

Extended Bonnet Ball ValveANSI Class 150 Flanged Ends, 275 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C.

FEATURES (1/2" to 2")• Investment cast components • Positive shut-off • Blow-out-proof stem design• PTFE seats and packing • Field repairable • Meets NACE MR-01-75• Spring-loaded adjustable packing • Corrosion resistant • Extended bonnet for insulation• Actuator mounting provisions• External connection for negative pressure scrubbing system (or monitoring)

STANDARD MATERIAL LIST1. Wheel handle 304 SS w/vinyl 8. Stop 304 SS2. Chevron packing PTFE 9. Stem A276-3163. Stem bearing RPTFE 10. Handle nut 304 SS4. Ball A276-316 11. Body seal RPTFE5. Seat (2) PTFE 12. Ground spring SS6. End cap (2) A351-CF8M 13. Threaded stud 316 SS, FEP coated7. Body A351-CF8M 14. Nut 316 SS, FEP coated

SS ANSI CLASS 150 FULL PORT FLANGEDEXTENDED BONNET BALL VALVE (1/2" to 2")

NUMBER SIZE A B C D E F G H I J K L Wt.452-203-01 1/2" .62 .62 4.25 2.12 2.37 3.87 7.38 4 3.50 1.38 .43 2.23 6.6452-204-01 3/4" .81 .62 4.62 2.31 2.75 3.87 7.48 4 3.88 1.69 .50 2.15 9.6452-205-01 1" 1.00 .62 5.00 2.50 3.12 3.87 7.59 4 4.25 2.00 .50 2.06 10.1452-207-01 1-1/2" 1.50 .62 6.50 3.25 3.87 5.62 8.10 4 5.00 2.87 .68 2.00 25.3452-208-01 2" 2.00 .75 7.00 3.50 4.75 5.62 8.51 4 6.00 3.62 .68 1.92 36.8



D-531/00


®

SS ANSI CLASS 150 FULL PORT FLANGEDEXTENDED BONNET BALL VALVE (3" to 6")

452-200 SeriesStainless Steel Class 150 Full Port Flanged


FEATURES (3" to 6")• Investment cast components • Positive shut-off • Blow-out-proof stem design• PTFE seats and packing • Field repairable • Meets NACE MR-01-75• Spring-loaded adjustable packing • Corrosion resistant • Extended bonnet for insulation• Actuator mounting provisions• External connection for negative pressure scrubbing system (or monitoring)

STANDARD MATERIAL LIST1. Gear operator Standard 3" to 6" 7. Body A351-CF8M2. Chevron packing PTFE 8. Stem A276-3163. Stem bearing RPTFE 9. Body seal RPTFE4. Ball A351-CF8M 10. Ground spring SS5. Seat (2) PTFE 11. Threaded stud 316 SS, FEP coated6. End cap (2) A351-CF8M 12. Nut 316 SS, FEP coated

NUMBER SIZE A B C D E F G H I J K L Wt.452-200-01 3" 3.00 .75 8.00 4.00 6.00 10.00 11.13 4 7.50 5.00 .75 2.12 105.0452-20A-01 4" 4.00 .75 9.00 4.50 7.50 10.00 11.84 8 9.00 6.18 .87 2.09 160.0452-20C-01 6" 6.00 .87 15.50 7.75 9.50 12.00 13.80 8 11.00 8.50 1.00 2.46 343.0



D-54 1/00


® 453-200 SeriesCarbon Steel Class 150 Full Port Flanged


FEATURES (1/2" to 2")• Investment cast components • Positive shut-off • Blow-out-proof stem design• PTFE seats and packing • Field repairable • Meets NACE MR-01-75• Spring-loaded adjustable packing • Corrosion resistant • Extended bonnet for insulation• Nitride corrosion protection • Actuator corrosion protection• External connection for negative pressure scrubbing system (or monitoring)

STANDARD MATERIAL LIST1. Wheel handle 304 SS w/vinyl 8. Stop 304 SS2. Chevron packing PTFE 9. Stem A276-3163. Stem bearing RPTFE 10. Handle nut 304 SS4. Ball A276-316 11. Body seal RPTFE5. Seat (2) PTFE 12. Ground spring SS6. End cap (2) A216-WCB 13. Threaded stud 316 SS, FEP coated7. Body A216-WCB 14. Nut 316 SS, FEP coated

CARBON STEEL ANSI CLASS 150 FULL PORT FLANGEDEXTENDED BONNET BALL VALVE (1/2" to 2")

NUMBER SIZE A B C D E F G H I J K L Wt.453-203-01 1/2" .62 .62 4.25 2.12 2.37 3.87 7.38 4 3.50 1.38 .43 2.23 6.6453-204-01 3/4" .81 .62 4.62 2.31 2.75 3.87 7.48 4 3.88 1.69 .50 2.15 9.6453-205-01 1" 1.00 .62 5.00 2.50 3.12 3.87 7.59 4 4.25 2.00 .50 2.06 10.1453-207-01 1-1/2" 1.50 .62 6.50 3.25 3.87 5.62 8.10 4 5.00 2.87 .68 2.00 25.3453-208-01 2" 2.00 .75 7.00 3.50 4.75 5.62 8.51 4 6.00 3.62 .68 1.92 36.8



D-551/00


® 453-200 SeriesCarbon Steel Class 150 Full Port Flanged


FEATURES (3" to 6")• Investment cast components • Positive shut-off • Blow-out-proof stem design• PTFE seats and packing • Field repairable • Meets NACE MR-01-75• Spring-loaded adjustable packing • Corrosion resistant • Extended bonnet for insulation• Nitride corrosion protection • Actuator mounting provisions• External connection for negative pressure scrubbing system (or monitoring)

STANDARD MATERIAL LIST1. Gear operator Standard 3" to 6" 7. Body A216-WCB2. Chevron packing PTFE 8. Stem A276-3163. Stem bearing RPTFE 9. Body seal RPTFE4. Ball A351-CF8M 10. Ground spring SS5. Seat (2) PTFE 11. Threaded stud 316 SS, FEP coated6. End cap (2) A216-WCB 12. Nut 316 SS, FEP coated

CARBON STEEL ANSI CLASS 150 FULL PORT FLANGEDEXTENDED BONNET BALL VALVE (3" to 6")

NUMBER SIZE A B C D E F G H I J K L Wt.453-200-01 3" 3.00 .75 8.00 4.00 6.00 10.00 11.13 4 7.50 5.00 .75 2.12 105.0453-20A-01 4" 4.00 .75 9.00 4.50 7.50 10.00 11.84 8 9.00 6.18 .87 2.09 160.0453-20C-01 6" 6.00 .87 15.50 7.75 9.50 12.00 13.80 8 11.00 8.50 1.00 2.46 343.0



D-56 1/00


NUMBER SIZE A B C D E F G H I J K L M WT.87A-403-01 1/2" 0.500 4.25 2.06 3.28 5.14 0.30 1.09 1.38 1.002 0.501 0.376 0.250 1/4-20 5.087A-404-01 3/4" 0.750 4.62 2.18 3.89 5.56 0.39 1.65 1.96 1.392 0.696 0.500 0.287 1/4-20 6.087A-405-01 1" 1.00 5.00 2.32 3.62 6.03 0.47 1.62 2.15 1.392 0.696 0.500 0.287 1/4-20 7.0

®

OPTIONS AVAILABLE:(SUFFIX) OPTION-01- Standard (Locking Kit and Grounded Stem)-14- Side Vented Ball (See Page J-2)-15- Wheel Handle-21- UHMWPE Seats-24- Fire Safe (Graphite Packing and Seal)-35- PTFE Seats and Seals-38- PEEK Seats and Graphite Packing-49- Assembled Dry-57- Oxygen Cleaned-60- Grounded Ball and Stem-65- MPTFE Seats and Graphite Packing-69- Drilled and Tapped Purge Port with Plug-70- 4" Extended Bonnet

MATERIALS OFCONSTRUCTIONDescription Material1. Body ASTM A351 CN7M2. Retainer ASTM B473 (UNS N08020)3. Ball ASTM B473 (UNS N08020)4. Stem ASTM B473 (UNS N08020)5. Packing Gland ASTM A276 Type 3166. Stem Seals PTFE7. Seats RPTFE8. Gland Screws ASTM A193 B8 Class 19. Gland Plate 302 or 304 SS









87A-400 SeriesAlloy 20 ANSI Class 150 Flanged Full Port Ball Valve -

1/2" through 1"

1/00

NEW FOR

2000


®

OPTIONS AVAILABLE:(SUFFIX) OPTION-01- Standard (Locking Kit and Grounded Stem)-14- Side Vented Ball (See Page J-2)-15- Wheel Handle-21- UHMWPE Seats-24- Fire Safe (Graphite Packing and Seal)-35- PTFE Seats and Seals-38- PEEK Seats and Graphite Packing-49- Assembled Dry-57- Oxygen Cleaned-60- Grounded Ball and Stem-65- MPTFE Seats and Graphite Packing-69- Drilled and Tapped Purge Port with Plug

MATERIALS OFCONSTRUCTIONDescription Material1. Body ASTM A351 CN7M2. Retainer ASTM B473 (UNS N08020)3. Ball ASTM B473 (UNS N08020)4. Stem ASTM B473 (UNS N08020)5. Packing Gland ASTM A276 Type 3166. Stem Seals PTFE7. Seats RPTFE8. Gland Screws ASTM A193 B8 Class 19. Gland Plate 302 or 304 SS









87A-400 SeriesAlloy 20 ANSI Class 150 Flanged Standard Port Ball Valve -

1-1/2" through 2"


NEW FOR

2000

1/00


NUMBER SIZE A B C D E F G H I J K L M N WT.87A-400-01 3" 2.50 8.00 3.51 6.23 8.40 0.80 3.93 4.70 1.949 0.974 0.750 0.477 5/16-18 3.00 34.3

®

OPTIONS AVAILABLE:(SUFFIX) OPTION-01- Standard (Locking Kit and Grounded Stem)-14- Side Vented Ball (See Page J-2)-21- UHMWPE Seats-24- Fire Safe (Graphite Packing and Seal)-35- PTFE Seats and Seals-38- PEEK Seats and Graphite Packing-49- Assembled Dry-57- Oxygen Cleaned-60- Grounded Ball and Stem-65- MPTFE Seats and Graphite Packing-69- Drilled and Tapped Purge Ports with Plugs-70- 4" Extended Bonnet-MG- Gear Operater with Standard Handwheel-MH- Gear Operater with Standard Handwheel & Locking

Device-MJ- Gear Operater with Oversize Handwheel-MK- Gear Operater with Oversize Handwheel & Locking

Device

MATERIALS OFCONSTRUCTIONDescription Material1. Body ASTM A351 CN7M2. Retainer ASTM A351 CN7M3. Ball ASTM B473 (UNS N08020) or CN7M4. Stem ASTM B473 (UNS N08020)5. Packing Gland ASTM A276 Type 3166. Stem Seals PTFE7. Seats RPTFE8. Gland Screws ASTM A193 B8 Class 19. Gland Plate 316 SS

10. Stem Nut 18-8 SS11. Lever 316 SS with Vinyl Grip12. Stem Bearing RPTFE13. Stop ASTM A276 Type 31614. Stop Screw 316 SS15. Lock Plate 302 or 304 SS16. Body Seal RPTFE17. Grounding Spring SS18. Body Joint Stud ASTM A193 Grade B8M19. Body Joint Nut ASTM A194 Grade 820. Lockwasher 302 or 304 SS








87A-400 SeriesAlloy 20 ANSI Class 150 Flanged Standard Port Ball Valve - 3"

1/00

NEW FOR

2000


®

OPTIONS AVAILABLE:(SUFFIX) OPTION-01- Standard (Locking Kit and Grounded Stem)-14- Side Vented Ball (See Page J-2)-21- UHMWPE Seats-24- Fire Safe (Graphite Packing and Seal)-35- PTFE Seats and Seals-49- Assembled Dry-57- Oxygen Cleaned-60- Grounded Ball and Stem-65- MPTFE Seats and Graphite Packing-69- Drilled and Tapped Purge Ports with Plugs-70- 4" Extended Bonnet-MG- Gear Operater with Standard Handwheel-MH- Gear Operater with Standard Handwheel & Locking

Device-MJ- Gear Operater with Oversize Handwheel-MK- Gear Operater with Oversize Handwheel & Locking

Device

MATERIALS OFCONSTRUCTIONDescription Material1. Body ASTM A351 CN7M2. Retainer ASTM A351 CN7M3. Ball ASTM B473 (UNS N08020) or CN7M4. Stem ASTM B473 (UNS N08020)5. Packing Gland ASTM A276 Type 3166. Stem Seals PTFE7. Seats RPTFE8. Gland Screws ASTM A193 B8 Class 19. Gland Plate 316 SS

10. Adapter Screw 18-8 SS11. Handle Adapter 316 SS with Vinyl Grip12. Stem Bearing RPTFE13. Stop ASTM A276 Type 31614. Stop Screw 316 SS15. Lock Plate 302 or 304 SS16. Body Seal RPTFE17. Grounding Spring SS18. Body Joint Stud ASTM A193 Grade B8M19. Body Joint Nut ASTM A194 Grade 820. Adapter Screw 18-8 SS21. Pipe Handle Galvanized Steel (not shown)








87A-400 SeriesAlloy 20 ANSI Class 150 Flanged Standard Port Ball Valve - 4"

NUMBER SIZE A B C D E F G H I J K L M N WT.87A-40A-01 4" 3.00 9.00 4.18 8.80 3.88 0.50 4.75 5.95 2.840 1.420 1.250 0.725 3/8-16 4.00 73.0

NEW FOR

2000

1/00

SECTION H CONTENTSSPECIALTY BALL VALVES

DESCRIPTION PAGE

7A-130-26 Series, Threaded Dry Chlorine Carbon Steel with Ni-Cu Ball & Stem H-1

7B-100 Series, Threaded Full Port Bronze H-2

7B-300 Series, Threaded Full Port Bronze H-3

7B-800 Series, M x F Threaded Full Port Bronze H-4

7H-800 Series, M x F Threaded Full Port Stainless Steel H-5

7K-100 Series, Threaded Full Port Bronze with Drain H-6

71-500 Series, Threaded “Deadman” Spring Return Handle Bronze H-7

74-100 Series, Threaded Chemical Resistant Nickel H-8

75-100 Series, Threaded Bronze Pad Locking Valve H-9

76-500 Series, Threaded “Deadman” Spring Return Handle Stainless Steel H-10

78-100 Series, Threaded Bronze with Dust Cover and Chain H-11

78-124 &-125, Threaded Bronze 5-Port Fuel Selector H-12

78-200 Series, Solder End Bronze with Dust Cover and Chain H-13

78-200 Series, Threaded Bronze Surface Mount H-14

78-255, Conbraco 4" Threaded Bronze H-15

78-257/267 Series, M x F Threaded Brass and Bronze Instrumentation H-16

78-621/625 Series, Threaded Bronze Irrigation H-17

78-664/666 Series, Threaded Bronze with Center Drain H-18

78-668, 3/4" Solder End Bronze Purge and Drain H-19

89-500 Series, Threaded “Deadman” Spring Return Handle Carbon Steel H-20

95-100 Series, Threaded Full Port Bronze Stop and Drain H-21

95-200 Series, Solder End Full Port Bronze Stop and Drain H-22

390-100 Series, NPT Full Port AAR Stainless Steel H-23

87-205-B6, 1" Flange x NPT Full Port AAR Stainless Steel H-24

87-208-A6, 2" Flange x NPT Full Port AAR Stainless Steel H-25

87-200-A4, 3" Flange x NPT Full Port AAR Stainless Steel H-26

82-200 Series, Male Brazed Extensions H-27

82-200 Series, Female Brazed Extensions H-28

65-008 Series, 2" x 6" & 3" x 6" Flanged Adaptor (Railcar Service) H-29

UL Listed and AGA Ball Valves - continued on next page

UL Listed and AGA Ball ValvesDESCRIPTION PAGE73-300 Series, Threaded, Carbon Steel, Double Union End H-30

73-400 Series, Socket Weld, Carbon Steel, Double Union End H-31

79-700 Series, Solder End Brass Full Port Refrigerant H-32

80-100 Series, Threaded Bronze Gas Shut-Off H-33

81-100 Series, Threaded Bronze Gas Shut-Off H-34

90-100 Series, Threaded Bronze Unibody, Saturn H-35

489-100 Series, Threaded Cast Carbon Steel H-36

50-GB0 Series, Threaded Bronze with Side Tap (GB-50 Series) H-37

51-GB0 Series, Threaded Bronze (GB-10 Series) H-38

51-GB0 Series, NPT x Flare Bronze (GB-11 Series) H-39

H-1COPYRIGHT ©1997 CONBRACO IND., INC. – PRINTED IN U.S.A.

® 7A-130-26 SeriesCarbon Steel Dry Chlorine Ball Valve

With Ni-Cu Ball and StemThreaded. 400 psig WOG, Cold Non-Shock.For Use With Dry Chlorine Gas and Dry Liquid.Federal Specification: WW-V-35C, Type: II, Composition: CS, Style: 3.Complies With Recommendations of Chlorine Institute Pamphlet No. 6.

FEATURES• Chevron style stem packing • Blow-out-proof stem design• Ni-Cu ball and stem • Bolted, adjustable packing gland• Investment Cast Parts • Vented ball• Nitride corrosion protection

STANDARD MATERIAL LIST1. Lever and grip 304 SS w/vinyl 8. Retainer A216-WCB2. Bolt (2) 18-8 SS 9. Body seal RPTFE3. Gland plate 304 SS 10. Stem bearing RPTFE4. Packing set PTFE, Chevron style 11. Stem B1645. Body A216-WCB 12. Packing gland A276-3166. Seats (2) RPTFE 13. Lever nut 18-8 SS7. Ball B164

NUMBER SIZE A B C D E Wt.7A-131-26 1/4" .43 1.56 2.75 1.93 3.87 1.257A-132-26 3/8" .50 1.56 2.75 1.93 3.87 1.217A-133-26 1/2" .50 1.56 2.75 1.93 3.87 1.147A-134-26 3/4" .68 2.00 3.50 2.31 4.87 2.117A-135-26 1" .87 2.37 4.12 2.43 4.87 2.947A-136-26 1-1/4" 1.00 2.24 4.24 3.00 5.50 4.407A-137-26 1-1/2" 1.25 2.65 5.13 3.38 8.00 7.047A-138-26 2" 1.50 3.25 6.00 3.67 8.00 10.86

CARBON STEEL DRY CHLORINE BALL VALVEWITH Ni-Cu BALL AND STEM


1/00

H-2 COPYRIGHT ©1997 CONBRACO IND., INC. – PRINTED IN U.S.A.

®7B-100 SeriesBronze Full Port Hydro Ball Valve


FEATURES• Chromium plated ball • Blow-out-proof stem design• RPTFE packing • Adjustable packing gland• PTFE seats

STANDARD MATERIAL LIST1. T-handle & grip SS w/vinyl 6. Gland nut B162. Stem packing RPTFE 7. Lever nut 304 SS3. Stem B16 8. Retainer B164. Ball B16, Chrome plated 9. Body B584-C844005. Seat (2) PTFE 10. Bearing RPTFE

1/4" to 1/2"

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-31 - Side Outlet Not Drilled & Tapped 1/4" to 2"

NUMBER SIZE A B C D E F G H Wt.7B-101-01 1/4" .37 1.03 2.06 1.37 2.68 .93 .53 1/8 NPT .617B-102-01 3/8" .37 1.03 2.06 1.37 2.68 .93 .53 1/8 NPT .577B-103-01 1/2" .50 1.09 2.18 1.43 2.68 1.00 .53 1/8 NPT .647B-104-01 3/4" .75 1.28 2.68 1.62 3.00 1.12 .75 1/8 NPT .807B-105-01 1" 1.00 1.66 3.43 1.90 4.00 1.31 .94 1/8 NPT 1.617B-106-01 1-1/4" 1.25 1.87 3.87 2.18 4.00 1.62 1.15 1/4 NPT 2.607B-107-01 1-1/2" 1.50 2.05 4.22 2.60 5.62 1.81 1.31 1/4 NPT 3.857B-108-01 2" 2.00 2.47 5.02 2.95 5.62 2.18 1.68 1/4 NPT 6.57

BRONZE FULL PORT HYDRO BALL VALVE


®


7B-300 SeriesSingle Union End Bronze Full Port Hydro Ball Valve

NPT Threaded, 400 psig WOG, Cold Non-Shock. 125 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: BZ, Style: 3.


STANDARD MATERIAL LIST1. T-handle & grip SS w/vinyl 7. Lever nut 304 SS2. Stem packing RPTFE 8. Retainer B163. Stem B16 9. Body B584-C844004. Ball B16, chrome plated 10. O-Ring Fluorocarbon5. Seat (2) PTFE 11. Tailpiece B166. Gland nut B16 12. Union nut B16 (1/4" to 1")

B584-C84400 (1-1/2" & 2")


NUMBER SIZE A B C D E F G H Wt.7B-301-01 1/4" .37 2.13 2.92 1.37 2.68 .93 .53 1/8 NPT .897B-303-01 1/2" .50 2.21 3.08 1.43 2.68 .93 .53 1/8 NPT 1.007B-304-01 3/4" .75 2.25 3.67 1.62 3.00 1.12 .75 1/8 NPT 1.327B-305-01 1" 1.00 2.71 4.50 1.90 4.00 1.31 .94 1/8 NPT 2.317B-306-01 1-1/4" 1.25 3.00 5.00 2.18 4.00 1.62 1.15 1/4 NPT 3.687B-307-01 1-1/2" 1.50 3.43 5.62 2.60 5.62 1.81 1.31 1/4 NPT 5.507B-308-01 2" 2.00 4.00 6.56 2.95 5.62 2.18 1.68 1/4 NPT 9.30

SINGLE UNION END BRONZEFULL PORT HYDRO BALL VALVE



®7B-800 SeriesMale x Female Bronze Full Port Hydro Ball Valve

Male x Female Threaded, 400 psig WOG, Cold Non-Shock, 125 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: BZ, Style: 3.


STANDARD MATERIAL LIST1. T-handle & grip SS 6. Stem B162. Stem packing RPTFE 7. Gland screw B163. Stem bearing RPTFE 8. Lever nut 304 SS4. Ball B16, chrome plated 9. Retainer B165. Seat (2) PTFE 10. Body B584-C84400


NUMBER SIZE A B C D E F G H Wt.7B-801-01 1/4" .37 1.40 2.43 1.37 2.56 .93 .53 1/8 NPT .737B-802-01 3/8" .37 1.46 2.50 1.37 2.56 .93 .53 1/8 NPT .707B-803-01 1/2" .50 1.68 2.78 1.43 2.56 1.00 .53 1/8 NPT .827B-804-01 3/4" .75 1.88 3.28 1.70 2.68 1.12 .75 1/8 NPT .807B-805-01 1" 1.00 2.39 4.17 1.93 3.62 1.31 .94 1/8 NPT 1.617B-806-01 1-1/4" 1.25 2.66 4.66 2.13 3.62 1.62 1.15 1/4 NPT 2.607B-807-01 1-1/2" 1.50 2.86 5.03 2.71 5.12 1.81 1.31 1/4 NPT 3.857B-808-01 2" 2.00 3.34 5.89 3.06 5.12 2.18 1.68 1/4 NPT 6.57

MALE x FEMALE BRONZEFULL PORT HYDRO BALL VALVE


MALE X FEMALE STAINLESS STEELFULL PORT HYDRO BALL VALVE

NUMBER SIZE A B C D E F G H Wt.7H-801-01 1/4" .37 1.47 2.46 1.39 2.56 .93 .53 1/8 NPT .657H-802-01 3/8" .37 1.55 2.54 1.39 2.56 .93 .53 1/8 NPT .627H-803-01 1/2" .50 1.79 2.83 1.45 2.56 1.00 .53 1/8 NPT .737H-804-01 3/4" .75 2.01 3.42 2.08 3.25 1.01 .75 1/8 NPT .867H-805-01 1" 1.00 2.39 4.17 2.38 3.93 1.12 .94 1/8 NPT 1.65


7H-800 SeriesM x F Stainless Steel Full Port Hydro Ball Valve

Male x Female Threaded, 800 psig WOG, Cold Non-Shock, 125 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: SS, Style: 3.

FEATURES• 316 SS ball & stem • Blow-out-proof stem design• RPTFE packing • Adjustable packing gland• PTFE seats

STANDARD MATERIAL LIST1. T-handle & grip SS 6. Stem A276-3162. Stem packing RPTFE 7. Gland screw A276-3163. Stem bearing RPTFE 8. Lever nut 304 SS4. Ball A276-316 9. Retainer A276-3165. Seat (2) PTFE 10. Body A351-CF8M

®




® 7K-100 SeriesBronze Full Port Ball Valve with Drain

NPT Threaded with NPT threaded drain port.Recommended for water or air services.Rated +50˚F to 200˚F, 0-125 psig.

FEATURES• Chromium plated ball • Blow-out-proof stem design• RPTFE seats and stuffing box ring • Adjustable packing gland• Mounting pad for easy actuator mounting • Full port for full flow & min. pressure drop

(3/4" to 2-1/2") • Auto-drain / Auto-vent

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 7. Gland nut B162. Stem packing RPTFE 8. Stem B163. Stem bearing RPTFE 9. Lever nut Steel, zinc plated4. Ball Brass, chrome plated 10. Body seal PTFE5. Seat (2) RPTFE (1-1/4" to 2-1/2")6. Retainer B16 (1/4" to 1") 11. Body B584-C84400

B584-C84400 (1-1/4" to 2-1/2")

VARIATIONS AVAILABLE:7K-150 Series (Original Balancing Stop)7K-190 Series (Pinned Retainer)

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02 - Static Grounded 1/4" to 2-1/2"-03 - 1-1/4" Stem Extension 1/4" to 2-1/2"-04 - 2-1/4" Stem Extension 1/4" to 2-1/2"-07 - Tee Handle 1/4" to 1-1/4"-08 - 90º Reversed Stem 1/4" to 2-1/2"-10 - SS Lever & Nut 1/4" to 2-1/2"-15 - Round Handle 1/4" to 1-1/4"-16 - Vertical Chain Lever 3/4" to 2-1/2"-17 - Rough Chrome Plating 1/4" to 2-1/2"-18 - Plain Yellow Grip 1/4" to 2-1/2"-24 - Graphite Stem Packing 1/4" to 2-1/2"-27 - Latch Lock Lever 1/4" to 2-1/2"-30 - CamLock Handle 1/4" to 1-1/4"-32 - SS Tee Handle & Nut 1/4" to 1-1/4"-35 - PTFE Trim 1/4" to 2-1/2"-40 - Cyl-Loc 1/4" to 1-1/4"-45 - Less Lever & Nut 1/4" to 2-1/2"-46- Lock In Closed Position 1/4" to 2-1/2"-47 - SS Latch-Lock Oval Handle 1/4" to 3/4"-48- SS Oval Handle 1/4" to 2"-49 - Assembled Dry 1/4" to 2-1/2"-50- 2-1/4” Locking Stem Extension 1/4" to 2-1/2"-56 - Multifill Seats 1/4" to 2-1/2"-57 - Cleaned for Gaseous Oxygen 1/4" to 2-1/2"-58 - Horizontal Chain Lever 3/4" to 2-1/2"-60 - Static Grounded Ball & Stem 1/4" to 2-1/2"-61 - Grounded Ball & Stem & Assembled Dry 1/4" to 2-1/2"-63 - NPT x Solder Retainer 1/4" to 2-1/2"

NUMBER SIZE A B C D E F G H I J K Wt.7K-101-01 1/4" .37 1.03 2.06 1.75 3.87 N/A N/A .09 .53 1.18 N/A .707K-102-01 3/8" .37 1.03 2.06 1.75 3.87 N/A N/A .09 .53 1.18 N/A .667K-103-01 1/2" .50 1.10 2.19 1.75 3.87 N/A N/A .12 .59 1.25 N/A .737K-104-01 3/4" .81 1.56 3.12 2.12 4.78 .87 1.37 .29 .90 1.56 .90 1.937K-105-01 1" 1.00 1.80 3.61 2.62 5.50 .93 1.50 .31 1.12 1.78 1.12 3.427K-106-01 1-1/4" 1.25 2.12 4.25 2.87 5.50 .93 1.50 .37 1.37 2.03 1.37 5.157K-107-01 1-1/2" 1.50 2.37 4.74 3.30 7.78 2.08 3.06 .50 1.56 2.21 1.28 6.817K-108-01 2" 2.00 2.70 5.38 3.71 7.78 2.41 3.52 .62 2.03 2.68 1.56 11.857K-109-01 2-1/2" 2.50 3.25 6.50 4.05 7.78 2.75 3.37 1.09 2.34 3.00 2.00 17.35

BRONZE FULL PORT BALL VALVE WITH DRAIN

H-6 1/00

COPYRIGHT ©1997 CONBRACO IND., INC. – PRINTED IN U.S.A. H-7

®71-500 SeriesBronze Ball Valve with “Deadman” Spring Return Handle

Threaded, 600 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: BZ Style: 3.

FEATURES• Spring return to close (-01) • Blow-out-proof stem design• Spring return to open (-08) • Adjustable packing gland• All components of lever are SS • Chromium plated ball• Operating torque is approximately three times standard valve torque• RPTFE seats and stuffing box ring

STANDARD MATERIAL LIST1. “Deadman” handle SS w/vinyl 6. Retainer B16 (1/4" to 1")2. Stem packing Multifill PTFE B584-C84400 (1-1/4" to 2")3. Stem bearing RPTFE 7. Gland nut B164. Ball B16, chrome plated 8. Stem A276-3165. Seat (2) Multifill PTFE 9. Lever nut Steel, zinc plated

10. Body seal PTFE (1-1/4" to 2")11. Body B584-C84400

VARIATIONS AVAILABLE:71-540 Series (316 SS Ball & Stem)71-590 Series (Pinned Retainer)

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-08 - 90º Reversed Stem (Spring Open) 1/4" to 2"-14 - Vented Ball(see page J-2) 1/4" to 2"-20 - Slot Vented Ball 1/4" to 2"-21 - UHMWPE Seats (Non-PTFE) 1/4" to 2"-24 - Graphite Stem Packing 1/4" to 2"-35 - PTFE Trim 1/4" to 2"-49 - Assembled Dry 1/4" to 2"-57 - Cleaned for Gaseous Oxygen 1/4" to 2"-P01- BSPP (Parallel) Thread Connection 1/4" to 2"-T01- BSPT (Tapered) Thread Connection 1/4" to 2"

NUMBER SIZE A B C D Wt.71-501-01 1/4" .43 1.12 2.25 7.00 1.4771-502-01 3/8" .50 1.12 2.25 7.00 1.4571-503-01 1/2" .50 1.12 2.25 7.00 1.3571-504-01 3/4" .68 1.50 3.00 7.00 2.3371-505-01 1" .87 1.68 3.37 7.00 2.5971-506-01 1-1/4" 1.00 2.00 4.00 9.00 4.1871-507-01 1-1/2" 1.25 2.18 4.37 9.00 5.3171-508-01 2" 1.50 2.34 4.68 9.00 6.41

BRONZE BALL VALVEWITH “DEADMAN”

SPRING RETURN HANDLE



74-100 SeriesChemical Resistant Nickel Ball Valve

Threaded, 800 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.

FEATURES• Investment cast components • Blow-out-proof stem design• RPTFE seats and stuffing box ring • Adjustable packing gland• SS lever and nut • (-24) Certified to API 607

4th Edition

STANDARD MATERIAL LIST1. Lever and grip 304 SS w/vinyl 7. Gland nut A276-3162. Stem packing RPTFE 8. Stem Nickel 200, ASTM-B1603. Stem bearing RPTFE 9. Lever nut 18-8 SS4. Ball Nickel 200, ASTM-B162 10. Body seal PTFE (1-1/2" & 2")5. Seat (2) RPTFE 11. Body Nickel CZ100, ASTM-A4946. Retainer Nickel 200, ASTM-B160 (1/2" to 1")

Nickel CZ100, ASTM-A494 (1-1/2" to 2")

®

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02 - Static Grounded 1/2" to 2"-03 - 1-1/4" Stem Extension 1/2" to 2"-04 - 2-1/4" Stem Extension 1/2" to 2"-07 - Tee Handle 1/2" to 2"-14 - Vented Ball(see page J-2) 1/2" to 2"-15 - Round Handle 1/2" to 2"-16 - Vertical Chain Lever 3/4" to 2"-18 - Plain Yellow Grip 1/2" to 2"-21 - UHMWPE Seats (Non-PTFE) 1/2" to 2"-24 - Graphite Stem Packing 1/2" to 2"-27 - Latch Lock Lever 1/2" to 2"-30 - CamLock Handle 1/2" to 2"-32 - SS Tee Handle & Nut 1/2" to 2"-35 - PTFE Trim 1/2" to 2"-45 - Less Lever & Nut 1/2" to 2"-46- Latch Lock Lever - Lock Close Only 1/2" to 2"-48- SS Oval Handle 1/2" to 2"-49 - Assembled Dry 1/2" to 2"-50- 2-1/4” Locking Stem Extension 1/2" to 2"-56 - Multifill Seats 1/2" to 2"-58 - Horizontal Chain Lever 3/4" to 2"-60 - Static Grounded Ball & Stem 1/2" to 2"-P01- BSPP (Parallel) Thread Connection 1/2" to 2"-T01- BSPT (Tapered) Thread Connection 1/2" to 2"

NUMBER SIZE A B C D E Wt.74-103-01 1/2" .50 1.12 2.25 1.75 3.87 .5874-104-01 3/4" .68 1.50 3.00 2.12 4.87 1.1874-105-01 1" .87 1.68 3.37 2.25 4.87 1.5774-107-01 1-1/2" 1.25 2.18 4.37 3.06 8.00 4.1174-108-01 2" 1.50 2.34 4.68 3.25 8.00 6.02

CHEMICAL RESISTANT NICKEL BALL VALVE



BRONZE PAD LOCKING BALL VALVE

®75-100 SeriesBronze Pad Locking Ball Valve


FEATURES• Chromium plated ball • Blow-out-proof stem design• RPTFE seats and stuffing box ring • Adjustable packing gland• May be padlocked in open or closed position with no change of hardware

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 7. Gland nut B162. Stem packing RPTFE 8. Stem B163. Stem bearing RPTFE 9. Lever nut Steel, zinc plated4. Ball B16, chrome plated 10. Body seal PTFE (1-1/4" & 2")5. Seat (2) RPTFE 11. Body B584-C844006. Retainer B16 (1/4" to 1")

B584-C84400 (1-1/4" to 2")

VARIATIONS AVAILABLE:75-140 Series (316 SS Ball & Stem)75-190 Series (Pinned Retainer)

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-02 - Static Grounded 1/4" to 2"-05 - Plain Ball 1/4" to 2"-08 - 90º Reversed Stem 1/4" to 2"-10 - SS Lever & Nut 1/4" to 2"-14 - Vented Ball(see page J-2) 1/4" to 2"-17 - Rough Chrome Plating 1/4" to 2"-18 - Plain Yellow Grip 1/4" to 2"-20 - Slot Vented Ball 1/4" to 2"-24 - Graphite Stem Packing 1/4" to 2"-41 - Automatic Drain 1/4" to 2"-49 - Assembled Dry 1/4" to 2"-57 - Cleaned for Gaseous Oxygen 1/4" to 2"-60 - Static Grounded Ball & Stem 1/4" to 2"-P01- BSPP (Parallel) Thread Connection 1/4" to 2"-T01- BSPT (Tapered) Thread Connection 1/4" to 2"


Pat. 3,865,130



76-500 SeriesStainless Steel Ball Valve with “Deadman”

Spring Return HandleThreaded, 1/4" to 1" 2000 psig WOG, 1-1/4" to 2" 1500 psig WOGCold Non-Shock. 150 psig Saturated Steam, Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: SS, Style: 3.

FEATURES• Spring return to close (-01) • Blow-out-proof stem design• Spring return to open (-08) • Adjustable packing gland• RPTFE seats and stuffing box ring • Meets NACE MR-01-75• All components of lever are stainless steel • Investment cast components• Operating torque is approximately three times standard valve torque

STANDARD MATERIAL LIST1. “Deadman” handle SS w/vinyl 6. Retainer A276-316 (1/4" to 1")2. Stem packing Multifill PTFE A351-CF8M (1-1/4" to 3. Stem bearing RPTFE 7. Gland nut A276-3164. Ball A276-316 8. Stem A276-3165. Seat (2) Multifill PTFE 9. Lever nut 18-8 SS

10. Body seal PTFE (1-1/4" to 2")11. Body A351-CF8M

®

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-08 - 90º Reversed Stem (Spring Open) 1/4" to 2"-14 - Vented Ball(see page J-2) 1/4" to 2"-21 - UHMWPE Seats (Non-PTFE) 1/4" to 2"-24 - Graphite Stem Packing 1/4" to 2"-35 - PTFE Trim 1/4" to 2"-49 - Assembled Dry 1/4" to 2"-57 - Cleaned for Gaseous Oxygen 1/4" to 2"-60 - Static Grounded Ball & Stem 1/4" to 2"-P01- BSPP (Parallel) Thread Connection 1/4" to 2"-T01- BSPT (Tapered) Thread Connection 1/4" to 2"


STAINLESS STEEL BALL VALVE WITH“DEADMAN” SPRING RETURN HANDLE



(1-1/4” to 2”)

1/00


BRONZE BALL VALVE WITH CAP AND CHAIN

®78-100 SeriesBronze Ball Valve With Dust Cover and Chain

Threaded x 3/4" Hose Connection.

FEATURES• Chromium plated ball • Blow-out-proof stem design• RPTFE seats and stuffing box ring • Adjustable packing gland• Securely attached dust cover with chain. (Dust cover cannot be used to contain pressure)

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 7. Gland nut B162. Stem packing RPTFE 8. Stem B163. Stem bearing RPTFE 9. Lever nut Steel, zinc plated4. Ball B16, chrome plated 10. Dust cover Diecast5. Seat (2) RPTFE 11. Body B584-C844006. Retainer B16

NUMBER SIZE A B C D E F Wt.

78-103-01 1/2" NPT x .50 1.68 2.81 2.95 3.87 1.75 .633/4" HOSE

78-104-01 3/4" NPT x .68 1.96 3.50 3.65 4.87 2.12 1.393/4" HOSE


78-124 & 78-125Bronze 5-Port Fuel Selector Ball Valve

Threaded. 50 psig WOG.

FEATURES• SS lever and nut • Blow-out-proof stem design• RPTFE bearing and packing • Adjustable packing gland• Non-lubricated design • PTFE seats• Operation: Four selected inlets feed on common outlet - pointer on

handle indicates the selected inlet

STANDARD MATERIAL LIST1. Lever and grip 304 SS w/vinyl2. Stem packing RPTFE3. Stem bearing RPTFE4. Ball B16, chrome plated5. Seat (4) PTFE6. Gland nut B167. Stem B168. Lever nut 304 SS9. Retainer (3) B16

10. Body B584-C84400

®

BRONZE 5-PORT FUEL SELECTOR BALL VALVENUMBER SIZE A B C D E F G H Wt./100

78-124-01 .50 1.26 2.52 2.27 3.53 1.12 10-24 1.40 1061/2"

78-125-01 3/4" .75 1.53 3.12 2.87 3.87 1.53 1/4-20 1.98 264

H

B

C

E

D

F

C

B

A Dia. PortTyp. 5pls


BRONZE BALL VALVE WITH CAP AND CHAIN

®78-200 SeriesBronze Ball Valve With Dust Cover And Chain

Solder End x 3/4" Hose Connection.

FEATURES• Chromium plated ball • Blow-out-proof stem design• RPTFE seats and stuffing box ring • Adjustable packing gland• Securely attached dust cover with chain. (Dust cover cannot be used to contain pressure)

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 7. Gland nut B162. Stem packing RPTFE 8. Stem B163. Stem bearing RPTFE 9. Lever nut Steel, zinc plated4. Ball B16, chrome plated 10. Dust cover Diecast5. Seat (2) RPTFE 11. Body B584-C844006. Retainer B16

The 78-200 is designed to be soft solderedinto lines without disassembly. This allowsa tested valve to be installed without disturbing the seats and seals in any way.Soldering temperature not to exceed 500ºF.

NUMBER SIZE A B C D E F G H Wt.

78-203-01 1/2" Solder .50 1.68 3.14 3.28 3.87 1.75 .500 .629 .71x 3/4" Hose

78-204-01 3/4" Solder .68 1.96 3.94 4.09 4.87 2.12 .750 .879 1.44x 3/4" Hose



NUMBER SIZE A B C D E F G Wt.78-248-01 1/4" .43 1.12 2.25 1.78 3.87 .93 1.87 .6878-250-01 3/8" .43 1.12 2.25 1.78 3.87 .93 1.87 .6878-256-01 1/2" .50 1.12 2.25 1.78 3.87 .93 1.87 .6578-438-01 3/4" .68 1.50 3.00 2.12 4.87 1.06 2.12 1.40

BRONZE THREADED SURFACE MOUNT BALL VALVE

® 78-200 SeriesBronze Threaded Surface Mount Ball Valve

NPT Threaded, 600 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: BZ, Style: 3.


STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 6. Retainer B162. Stem packing RPTFE 7. Gland nut B163. Stem bearing RPTFE 8. Stem B164. Ball B16, chrome plated 9. Lever nut Steel, zinc plated5. Seat (2) RPTFE 10. Body B584-C84400


NUMBER SIZE A B C D E Wt.78-255-01 4" 3.12 3.68 7.37 5.25 10.00 25.50

4“ BRONZE BALL VALVE

78-255-014" Bronze Ball Valve

4" Threaded. 150 psig WOG, Cold Non-Shock. 50 psig Saturated Steam.

FEATURES• Chromium plated ball • Blow-out-proof stem design• RPTFE stuffing box ring • Adjustable packing gland• PTFE seats

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 6. Retainer B584-C844002. Stem packing RPTFE 7. Gland nut B163. Stem bearing RPTFE 8. Stem B164. Ball B584-C84400, chrome plated 9. Lever nut Steel, zinc plated5. Seat (2) PTFE 10. Body B584-C84400

NOTE: Options Are Not Available For This Valve.

BRONZE INSTRUMENTATION BALL VALVESCREW SLOT

NUMBER SIZE A B C D E Cv* Wt.78-257-01 1/8"M x 1/4"F .21 .80 1.60 .72 N/A 4.0 .1978-258-01 1/4"M x 1/4"F .31 .80 1.60 .72 N/A 5.5 .19

BRONZE INSTRUMENTATION BALL VALVELEVER HANDLE

NUMBER SIZE A B C D E Cv* Wt.78-267-01 1/4"M X 1/4"F .25 .65 1.45 .93 1.37 5.5 .20

BRASS INSTRUMENTATION BALL VALVETEE HANDLE

NUMBER SIZE A B C D E Cv* Wt.78-260-05 1/8"M x 1/8"F .21 .37 1.43 .87 1.25 4.0 .2078-261-05 1/4"M x 1/4"F .31 .43 1.43 .87 1.25 5.5 .19

BRASS INSTRUMENTATION BALL VALVESCREW SLOT

NUMBER SIZE A B C D E Cv* Wt.78-262-05 1/8"M X 1/8"F .21 .37 1.43 .75 N/A 4.0 .2078-263-05 1/4"M X 1/4"F .31 .43 1.43 .75 N/A 5.5 .19


®78-257/267 SeriesBrass And Bronze Instrumentation Ball Valve

Male x Female Threaded. 400 psig WOG, Cold Non-Shock. Air & Liquid Service Rating.

FEATURES• Micro-finish ball • Blow-out-proof stem design • PTFE seats• Nitrile stem seal • Plated steel tee handle • Compact design• Optional mixed end fittings available

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl2. Drive pin Steel, zinc plated3. O-Ring Nitrile4. Stem B165. Seat (2) PTFE6. Stem boss B167. Ball* B168. Stem screw Steel, zinc plated9. Retainer B16

10. Body B16 or B584-C84400

* Chrome Plated Ball In Bronze Valves.

*The Cv factor is the gallons of water per minute that the valve will pass with a 1 psigpressure drop.



®78-621/625 SeriesBronze Irrigation Ball Valve

Threaded. 600 psig Water, Cold Non-Shock.

FEATURES• Chromium plated ball • Blow-out-proof stem design• RPTFE seats and stuffing box ring • Adjustable packing gland• Temperature range: +50ºF to +400ºF

STANDARD MATERIAL LIST1. Head adapter A351-CF8M 7. Gland nut B162. Stem packing RPTFE 8. Stem B163. Stem bearing RPTFE 9. Screw SS4. Ball B16, chrome plated 10. Retainer B16 (3/4" to 1") B584-C84400 (1-1/4" to 2")5. Seat (2) RPTFE 11. Body B584-C844006. Body seal PTFE (1-1/4" to 2")

Caution: Do not use where drained media could cause damage.See options section (option -41) for description of Auto-Drain feature.

NUMBER SIZE A B C D E Wt.78-621-01 3/4" .68 1.47 2.96 2.40 1.81 1.5978-622-01 1" .87 1.66 3.34 2.53 1.81 1.9278-623-01 1-1/4" 1.00 1.98 3.97 3.00 2.50 3.5778-624-01 1-1/2" 1.25 2.12 4.28 3.18 2.50 4.6878-625-01 2" 1.50 2.35 4.67 3.37 2.50 6.11

BRONZE IRRIGATION BALL VALVE

FEATURES:• Automatic Draining in

the Off Position• SS Underground Curb

Stop Handle

Drain Port

For Pressure/Temperature Ratings,Refer to Page J-8


®78-664/78-962 SeriesBronze Ball Valve With Center Drain


FEATURES• Chromium plated ball • Blow-out-proof stem design• RPTFE seats and stuffing box ring • Adjustable packing gland• Mounting pad with bonding screw • Drainable ball cavity to prevent freeze damage

STANDARD MATERIAL LIST1. Lever and grip 304 SS w/vinyl 7. Gland nut B162. Stem packing RPTFE 8. Stem B163. Stem bearing RPTFE 9. Lever nut SS4. Ball B16, chrome plated 10. Body seal PTFE (1-1/4" to 2")5. Seat (2) RPTFE 11. Body B584-C844006. Retainer B16 (3/4" & 1") 12. Drain plug B16

B584-C84400 (1-1/4" to 2") 13. Screw Brass

NUMBER SIZE A B C D E F G H Wt.78-664-01 3/4" .68 1.50 3.00 2.12 4.87 .87 1.37 .17 1.5378-665-01 1" .87 1.68 3.37 2.25 4.87 .87 1.37 .21 1.8678-666-01 1-1/4" 1.00 2.00 4.00 2.62 5.50 .93 1.50 .28 3.3978-667-01 1-1/2" 1.25 2.18 4.37 3.05 8.00 .93 1.50 .40 4.6878-962-01 2" 1.50 2.34 4.68 3.24 8.00 .93 1.50 .45 5.72

BRONZE BALL VALVE WITH CENTER DRAIN


3/4” - 1”..10-24 NC1-1/4” - 2”...20 NC

1/00


78-668Bronze Purge And Drain Ball Valve

Solder End Flow Port, Hose Connection Drain Port. 600 psig WOG, Cold Non-Shock.

FEATURES• Chromium plated ball • Blow-out-proof stem design• RPTFE seats and stuffing box ring • Adjustable packing gland• Hose thread connection for disposal of drained media • Furnished with dust cover* and chain

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 8. Port Cap B162. Stem packing RPTFE 9. Stem B163. Stem bearing RPTFE 10. Lever nut Steel, zinc plated4. Ball B16, chrome plated 11. Body B584-C844005. Seat (2) RPTFE 12. Washer 316 SS6. Solder Retainer (2) B16 13. Gland screw B167. Hose Retainer B16 14. Dust cover B16

The 78-668 is designed to be soft soldered into lineswithout disassembly. This allows a tested valve to beinstalled without disturbing the seats and seals in anyway. Soldering temperature not to exceed 500ºF.

* Dust cover cannot be used to contain pressure.

FLOW PATTERN


®

BRONZE PURGE & DRAIN BALL VALVENUMBER SIZE A B C D E F G H J Wt.

78-668-01 3/4" .64 2.19 4.37 1.62 2.59 3.56 1.50 .88 .75 2.66

78-668-02 1" .75 2.41 4.82 1.91 3.56 5.33 1.91 1.13 .90 2.75

F

G

BC

D

E

J

H


®89-500 SeriesCarbon Steel Ball Valve With “Deadman”

Spring Return HandleThreaded, 1/4"to 1" 2000 psig WOG, 1-1/4" to 2" 1500 psig WOG.Cold Non-Shock, 150 psig Saturated Steam, Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: CS, Style: 3.

FEATURES• Spring return to close (-01) • Blow-out-proof stem design• Spring return to open (-08) • Adjustable packing gland• RPTFE stuffing box ring • Investment cast components• All components of lever are stainless steel • Multifill seats• Nitride corrosion protection• Operating torque is approximately three times standard valve torque

STANDARD MATERIAL LIST1. “Deadman” handle SS 6. Retainer A108-CS (1/4" to 1")2. Stem packing Multifill PTFE A216-WCB (1-1/4" to 2")3. Stem bearing RPTFE 7. Gland nut A108-CS4. Ball A108-CS chrome plated 8. Stem A108-CS5. Seat (2) Multifill PTFE 9. Lever nut Steel, Zinc Plated

10. Body seal PTFE (1-1/4" to 2")11. Body A216-WCB


OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-08 - 90º Reversed Stem (Spring Open) 1/4" to 2"-14 - Vented Ball(see page J-2) 1/4" to 2"-21 - UHMWPE Seats (Non-PTFE) 1/4" to 2"-24 - Graphite Stem Packing 1/4" to 2"-35 - PTFE Trim 1/4" to 2"-P01- BSPP (Parallel) Thread Connection 1/4" to 2"-T01- BSPT (Tapered) Thread Connection 1/4" to 2"


CARBON STEEL BALL VALVE WITH“DEADMAN” SPRING RETURN HANDLE



(1-1/4” to 2”)


®95-100 SeriesBronze Full Port Stop and Drain Ball Valve

Threaded, 400 psig WOG, Cold Non-Shock.Federal Specification: WW-V-35C, Type: II, Composition: BZ, Style: 3.

FEATURES• Chromium plated ball • Blow-out-proof stem design• RPTFE seats and stuffing box ring • Adjustable packing gland• Drain cap designed to prevent loss • Rugged construction

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 7. Stem B162. Gland screw B16 8. Ball B16, chrome plated3. Lever nut Zinc plated steel 9. Retainer B164. Seat (2) RPTFE 10. Body B584-C844005. Stem packing RPTFE 11. Cap and seal B16 and EPR6. Stem bearing RPTFE

VARIATIONS AVAILABLE:95-120 Series (Adjustable Stop Lever)

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-07 - Tee Handle 1/2" to 1"-08 - 90º Reversed Stem 1/2" to 1"-10 - SS Lever & Nut 1/2" to 1"-14 - Vented Ball(see page J-2) 1/2" to 1"-15 - Round Handle 1/2" to 1"-18 - Plain Yellow Grip 1/2" to 1"-20 - Slot Vented Ball 1/2" to 1"-27 - Latch Lock Lever 1/2" to 1"-32 - SS Tee Handle & Nut 1/2" to 1"-45 - Less Lever & Nut 1/2" to 1"-46- Latch Lock Lever - Lock Close Only 1/2" to 1"-48 - SS Oval Handle 1/2" to 1"-49 - Assembled Dry 1/2" to 1"-63 - Threaded x Solder Retainer 1/2" to 1"

NUMBER SIZE A B C D E Wt.95-103-01 1/2" .50 1.09 2.18 1.75 3.87 .6395-104-01 3/4" .81 1.56 3.12 2.15 4.87 1.3995-105-01 1" 1.00 1.81 3.62 2.43 4.87 1.70

BRONZE FULL PORT STOP ANDDRAIN BALL VALVE



®

NUMBER SIZE A B C D E F G Wt.95-203-01 1/2" .50 1.43 2.87 1.75 3.87 .628 .50 .7095-204-01 3/4" .81 2.12 4.12 2.15 4.87 .878 .75 1.2395-205-01 1" 1.00 2.21 4.43 2.43 4.87 1.128 .90 1.90

BRONZE SOLDER END STOP AND DRAINFULL PORT BALL VALVE

95-200 SeriesBronze Solder End Full Port Stop and Drain Ball Valve

Solder End, 400 psig WOG, Cold Non-Shock.Federal Specification: WW-V-35C, Type: II, Composition: BZ, Style: 3.

FEATURES• Chromium plated ball • Blow-out-proof stem design• RPTFE seats and stuffing box ring • Adjustable packing gland• Drain cap designed to prevent loss • Rugged construction

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 7. Stem B162. Gland screw B16 8. Ball B16, chrome plated3. Lever nut Steel, zinc plated 9. Retainer B164. Seat (2) RPTFE 10. Body B584-C844005. Stem packing RPTFE 11. Cap and seal B16 and EPR6. Stem bearing RPTFE

The 95-200 is designed to be soft solderedinto lines without disassembly. This allowsa tested valve to be installed withoutdisturbing the seats and seals in any way.Soldering temperatures not to exceed 500ºF.

VARIATIONS AVAILABLE:95-220 Series (Adjustable Stop Lever)

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-07 - Tee Handle 1/2" to 1"-08 - 90º Reversed Stem 1/2" to 1"-10 - SS Lever & Nut 1/2" to 1"-14 - Vented Ball(see page J-2) 1/2" to 1"-15 - Round Handle 1/2" to 1"-18 - Plain Yellow Grip 1/2" to 1"-20 - Slot Vented Ball 1/2" to 1"-24 - Graphite Stem Packing 1/2" to 1"-27 - Latch Lock Lever 1/2" to 1"-32 - SS Tee Handle & Nut 1/2" to 1"-45 - Less Lever & Nut 1/2" to 1"-46- Latch Lock Lever - Lock Close Only 1/2" to 1"-48 - SS Oval Handle 1/2" to 1"-49 - Assembled Dry 1/2" to 1"



® 390-100 SeriesStainless Steel Full Port AAR Ball Valve

390-105-01 AAR Approval #E929027, 390-108-01 AAR Approval #E929028NPT Threaded, 275 psig WOG, Cold Non-Shock, 150 psig Saturated Steam. Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: SS, Style: 3.

FEATURES• AAR Approved • Meets NACE MR-01-75 • Blow-out-proof stem design• Investment cast body and retainer • Positive shut-off • Field repairable• Adjustable packing gland • Corrosion resistant • Bolted body design• Graphite body seal and packing • RPTFE seats • Compact design

STANDARD MATERIAL LIST1. Lever and grip 304 SS w/vinyl 9. Lever lock nut A194-GD8 SS2. Stem packing Graphite 10. Body A351-CF8M3. Stem bearing RPTFE 11. Body seal Graphite4. Ball A276-316 12. Lock washer 410 SS5. Seat (2) RPTFE 13. Body bolt A193-GDB8 SS6. Retainer A351-CF8M 14. Body nut A194-GD8 SS7. Gland screw A276-316 15. Ground spring SS8. Stem A276-316 16. Lock washer 304 SS

NUMBER SIZE A B C D E Wt.390-105-01 1" 1.00 2.09 4.18 2.62 5.50 4.00390-108-01 2" 2.00 2.70 5.40 4.08 6.00 13.00

STAINLESS STEEL FULL PORT AAR BALL VALVE



® 87-205-B61" Stainless Steel Full Port Flange x NPT AAR Ball Valve

AAR Approval #E919013ANSI Class 150 Flange x NPT Threaded Ends, 275 psig WOG, Cold Non-Shock 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: SS, Style: 3.

FEATURES• AAR Approved • Meets NACE MR-01-75 • Blow-out-proof stem design• Investment cast body and retainer • Positive shut-off • Field repairable• Adjustable packing gland • Corrosion resistant • Bolted body design• Graphite body seal and packing • RPTFE seats • Compact design



WEIGHT = 5.50 lbs


WEIGHT = 20.50 lbs

® 87-208-A62" Stainless Steel Full Port Flange x NPT AAR Ball Valve

AAR Approval #E919013

ANSI Class 150 Flange x NPT Threaded Ends, 275 psig WOG, Cold Non-Shock 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: SS, Style: 3.

FEATURES• AAR Approved • Meets NACE MR-01-75 • Blow-out-proof stem design• Investment cast body and retainer • Positive shut-off • Field repairable• Adjustable packing gland • Corrosion resistant • Bolted body design• Graphite body seal and packing • RPTFE seats • Reversed operation




® 87-200-A4 Series3" Stainless Steel Full Port Flange x NPT AAR Ball Valve

AAR Approval #E9190114ANSI Class 150 Flange x NPT Threaded Ends, 275 psig WOG, Cold Non-Shock 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: SS, Style: 3.

FEATURES• AAR Approved • Meets NACE MR-01-75 • Blow-out-proof stem design• Graphite body seal and packing • Bolted body design • Field repairable• Adjustable packing gland • Corrosion resistant • Positive shut-off• RPTFE seats • Investment cast lever

STANDARD MATERIAL LIST1. Lever A351-CF8M 10. Body A351-CF8M2. Stem packing Graphite 11. Body seal Graphite3. Stem bearing RPTFE 12. Gland plate 304 SS4. Ball A351-CF8M 13. Screw A193-GDB8 SS5. Seat (2) RPTFE 14. Stop A276-3166. Retainer A351-CF8M 15. Lock washer 410 SS7. Packing gland A276-316 16. Body bolt A193-GDB8M SS8. Stem A276-316 17. Body lock nut A194-GD8 SS9. Lever screw A193-GDB8M SS 18. Lock washer 304 SS

NUMBER SIZE A B C D E F G H I J Wt.87-200-A4 3" 3.00 .75 7.68 3.68 6.00 9.00 5.46 7.50 5.00 .75 50.0087-200-A46* 3" 3.00 .75 7.68 3.68 6.00 6.00 5.46 7.50 5.00 .75 50.00

3" STAINLESS STEEL FULL PORTFLANGE X NPT AAR BALL VALVE


1/00

*With 6" Lever


®82-200 SeriesBronze 3-Piece Full Port Ball Valve With Male

Brazed ExtensionsSolder End, 600 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35B, Type: II, Composition: BZ, Style: 1.Designed for soft solder or brazed installation without disassembly.

FEATURES• Full port configuration • Blow-out-proof stem design• RPTFE seats and seals • Adjustable packing gland• In-line repairable • Latch lock handle optional

STANDARD MATERIAL LIST

BRONZE 3-PIECE FULL PORT BALL VALVE WITH MALE BRAZED EXTENSIONSSTANDARD OXYGEN CLEANED

PART NO. PART NO.PART W/316 SS PART W/316 SS

NUMBERS BALL & STEM NUMBERS BALL & STEM SIZE A B C D E F G* Wt.82-203-B8 82-243-A8 82-203-A1 82-243-A7 1/2" .62 6.90 13.81 2.00 4.87 .049 5/8" 1.6682-204-A8 82-244-B3 82-204-A2 82-244-B2 3/4" .81 6.96 13.93 2.18 4.87 .065 7/8" 2.3782-205-B7 82-245-B1 82-205-A1 82-245-B0 1" 1.00 6.97 13.95 2.62 5.50 .065 1-1/8" 3.4382-206-B7 82-246-B0 82-206-A1 82-246-A9 1-1/4" 1.25 7.40 14.75 2.89 5.50 .065 1-3/8" 5.5282-207-B2 82-247-B2 82-207-A1 82-247-B0 1-1/2" 1.50 7.53 15.07 3.37 8.00 .072 1-5/8" 8.5182-208-B7 82-248-B2 82-208-A1 82-248-B1 2" 2.00 7.61 15.23 3.70 8.00 .083 2-1/8" 14.20

*NOMINAL TUBING O.D.


1. Lever and grip Steel, zinc plated w/vinyl2. Stem packing RPTFE3. Stem bearing RPTFE4. Ball B16, chrome plated5. Seat (2) RPTFE6. End cap (2) B16 (3/8")

B584-C84400 (1/2" to 2")7. Gland B16

8. Stem B169. Lever nut Steel, zinc plated

10. Body bolt Steel, zinc plated11. Hex nut Steel, zinc plated12. Body B584-C8440013. Extension Type K copper tubing14. Brazing alloy Sil-Fos 515. Cap plugs (not shown)

BRONZE 3-PIECE FULL PORT BALL VALVE WITH FEMALE BRAZED EXTENSIONSSTANDARD OXYGENNUMBERS CLEANED SIZE A B C D E F G* H Wt.82-203-C2 82-203-C3 1/2" .62 7.40 14.80 2.00 4.87 .50 5/8" .049 1.782-204-C3 82-204-C4 3/4" .81 7.71 15.42 2.18 4.87 .75 7/8" .065 2.482-205-C2 82-205-C3 1" 1.00 7.92 15.84 2.62 5.50 .90 1-1/8" .065 3.582-206-C1 82-206-C2 1-1/4" 1.25 8.45 16.90 2.89 5.50 .96 1-3/8" .065 5.682-207-B8 82-207-B9 1-1/2" 1.50 8.58 17.16 3.37 8.00 1.09 1-5/8" .072 8.682-208-C1 82-208-C2 2" 2.00 9.06 18.12 3.70 8.00 1.34 2-1/8" .083 14.3


® 82-200 SeriesBronze 3-Piece Full Port Ball Valve With 6” Female

Brazed ExtensionsSolder End, 600 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35B, Type: II, Composition: BZ, Style: 1.Designed for soft solder or brazed installation without disassembly.

FEATURES• Full port configuration • Blow-out-proof stem design• RPTFE seats & seals • Adjustable packing gland• In-line repairable • Latch lock handle optional


*NOMINAL TUBING O.D.


1. Lever and grip Steel, zinc plated w/vinyl2. Stem packing RPTFE3. Stem bearing RPTFE4. Ball B16, chrome plated5. Seat (2) RPTFE6. End cap (2) B16 (3/8")

B584-C84400 (1/2" to 2")7. Gland B16

8. Stem B169. Lever nut Steel, zinc plated

10. Body bolt Steel, zinc plated11. Hex nut Steel, zinc plated12. Body B584-C8440013. Extension Type K copper tubing14. Brazing alloy Sil-Fos 515. Cap plugs (not shown)


® 65-008 SeriesStainless Steel Tank Car Valve Adaptors

AAR Approved #E989075

NUMBER SIZE A B C D E F G H I Wt.65-008-31 2 x 6 2.06 4.00 4.75 10.31 9.00 8.25 .68 2.65 .75 18.8565-008-30 3 x 6 3.06 5.25 6.00 10.31 9.00 8.25 .68 2.03 .75 14.40

STAINLESS STEEL TANK CAR VALVE ADAPTORS

1/00


® 73-300 SeriesCarbon Steel Double Union End Ball Valve

Threaded, 3000 psig WOG, Cold Non-Shock, 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: CS, Style: 1.


UL LISTING @ 250 PSIG MAX• Guide YRPV: Gas shutoff valve for use with natural and manufactured gases.• Guide YSDT: LP gas shutoff valve.• Guide YRBX: Flammable liquid shutoff valve.




CARBON STEEL DOUBLE UNION ENDBALL VALVE


1. Lever and grip Steel, zinc plated w/vinyl2. Stem packing RPTFE3. Stem bearing RPTFE4. Ball A108-CS chrome plated5. Tailpiece (2) A108-CS6. Retainer A108-CS7. Gland nut A108-CS8. Stem A108-CS chrome plated

9. Lever nut Steel, zinc plated10. Body A108-CS11. Seat (2) RPTFE12. Union nut (2) A108-CS13. Seat holder A108-CS14. Union seal (2) RPTFE15. Retainer seal RPTFE

VARIATIONS AVAILABLE:73-340 Series (316 SS ball & Stem)

® 73-400 SeriesCarbon Steel Double Union End Socket Weld Ball Valve

Socket Weld End, 3000 psig WOG, Cold Non-Shock, 150 psig Saturated Steam.Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: CS, Style: 1.


UL LISTING @ 250 PSIG MAX• Guide YRPV: Gas shutoff valve for use with natural and manufactured gases.• Guide YSDT: LP gas shutoff valve.• Guide YRBX: Flammable liquid shutoff valve.




CARBON STEEL DOUBLE UNION ENDSOCKET WELD BALL VALVE


1. Lever and grip Steel, zinc plated w/vinyl2. Stem packing RPTFE3. Stem bearing RPTFE4. Ball A108-CS chrome plated5. Seat (2) RPTFE6. Retainer A108-CS7. Gland nut A108-CS8. Stem A108-CS chrome plated

9. Lever nut Steel, zinc plated10. Body A108-CS11. Tail Piece (2) A108-101812. Union nut (2) A108-CS13. Seat holder A108-CS14. Union seal (2) RPTFE15. Retainer seal RPTFE




® 79-700 SeriesFull Port Forged Brass Refrigerant Ball Valve

FEATURES• Bi-directional flow design • Blow-out-proof stem design• RPTFE seats and seals • Adjustable packing gland• Chromium plated pressure equalizing ball • Hermetic welded assembly• Exclusive design rotation stops • Full Port Design• Copper extensions silver brazed to body allows use of Sil-Fos• Capped, triple sealed stem with metal back up reduces leaks

UL LISTINGS• Guide SFJQ: Valves, Refrigerant

STANDARD MATERIAL LIST1. Cap B16 8. O-Ring Neoprene2. Stem packing RPTFE 9. Stop Plate Steel, Plated3. Stem bearing RPTFE 10. Hex nut B164. Ball B16, Chrome plated 11. Retainer B165. Seat (2) RPTFE 12. Tube extension Copper tubing6. Packing gland B16 13. Body Forged brass7. Stem B16

NUMBER SIZE A B C D E F Wt. Cv79-701-01 3/8" .32 3.18 6.09 1.55 .38 .38 .94 2.9 10.879-702-01 1/2" .45 3.18 6.09 1.55 .38 .50 .94 5.6 13.379-703-01 5/8" .50 3.43 6.59 1.55 .50 .62 .94 13.1 10.479-704-01 7/8" .75 3.69 7.07 1.83 .75 .87 1.31 31.9 11.279-705-01 1-1/8" 1.00 4.20 8.00 2.01 .90 1.12 2.06 68.0 10.779-706-01 1-3/8" 1.25 4.54 8.63 2.61 .96 1.38 4.00 109 11.679-707-01 1-5/8" 1.50 4.47 8.85 2.79 1.09 1.62 4.25 152 13.279-708-01 2-1/8" 2.00 4.84 9.59 3.17 1.34 2.12 6.00 275 15.179-709-01 2-5/8" 2.43 5.00 10.00 3.90 1.48 2.62 17.50 349 21.179-600-01* 3-1/8" 2.50 7.00 14.00 3.90 1.67 3.13 17.60 391 30.1

FULL PORTFORGED BRASS REFRIGERANT BALL VALVE

* Note: 3-1/8” size is not full port


UL®

LISTED

EquivalentLength oftube

1/00

BRONZE LP-GAS BALL VALVE

® 80-100 SeriesBronze LP-Gas Ball Valve

Threaded, 600 psig WOG, Cold Non-Shock. 250 psig LP-Gas.150 psig Saturated Steam. Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: BZ, Style: 3.

FEATURES• UL Listed for LP-Gas, natural gas, flammable liquid and heated oil• Large ports to reduce pressure drop • Adjustable packing gland• RPTFE seats and seals • Optional tee handle available (-07) • One piece bronze body• Blow-out-proof stem design • Quarter turn On-Off • Chromium plated ball

UL LISTINGS• Guide YSDT: LP-Gas shut-off valve.• Guide YRPV: Gas shut-off valve for use with natural and manufactured gases.• Guide YRBX: Flammable liquid shutoff valve.• Guide MHKZ: No. 6 oil at 250ºF.

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 6. Retainer B16 or B584-C844002. Stem packing RPTFE 7. Gland nut B163. Stem bearing RPTFE 8. Stem B164. Ball B16, chrome plated 9. Lever nut Steel, zinc plated5. Seat (2) RPTFE 10. Seal PTFE (1-1/4" to 3")

11. Body B584-C84400

UL®

LISTED


Note: 250 psig Max. UL Listing.



OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-27 - Latch Lock Lever 1/4" to 3"

1/00


® 81-100 SeriesBronze LP-Gas Ball Valve With Plain Ball

Threaded, 600 psig WOG, Cold Non-Shock. 250 psig LP-Gas.150 psig Saturated Steam. Vacuum Service to 29 inches Hg.Federal Specification: WW-V-35C, Type: II, Composition: BZ, Style: 3.

FEATURES• UL Listed for LP-Gas, natural gas, flammable liquid and heated oil• Large ports to reduce pressure drop • Adjustable packing gland• RPTFE seats and seals • Optional tee handle available (-07) • One piece bronze body• Blow-out-proof stem design • Quarter turn On-Off • Plain ball


STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 6. Retainer B16 or B584-C844002. Stem packing RPTFE 7. Gland nut B163. Stem bearing RPTFE 8. Stem B164. Ball B16 9. Lever nut Steel, zinc plated5. Seat (2) RPTFE 10. Seal PTFE (1-1/4" to 3")

11. Body B584-C84400


BRONZE LP-GAS BALL VALVE

UL®

LISTED




For Pressure/Temperature Ratings,Refer to Page 10 , Graph No. 3

90-100 SeriesBronze Uni-Body Saturn® Ball Valve

Threaded, 300 psig WOG, Cold Non-Shock. 150 psig Saturated Steam.Federal Specification: WW-V-35C, Type: II, Composition: BZ, Style: 3.

FEATURES• UL Listed at 300 psig for fuel, inert gas and flammable liquids • Adjustable packing gland• Valves with tee handles UL listed • One piece bronze body• RPTFE seats and seals • Chromium plated ball• Blow-out-proof stem design • Compact

UL LISTINGS• Guide YRPV: Gas shutoff valve for use with natural and manufactured gases.• Guide YQNZ: Compressed gas shutoff valve for use with air, inert gases, hydrogen,

oxygen and common refrigerants except ammonia.• Guide YRBX: Flammable liquid shutoff valve.

STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl 6. Retainer B162. Stem packing RPTFE 7. Gland nut B163. Stem bearing RPTFE 8. Stem B164. Ball B16, chrome plated 9. Lever nut (Screw 1/2") Steel, zinc plated5. Seat (2) RPTFE 10. Body B584-C84400

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-05- Plain Ball 1/2" to 2"-07 - Tee Handle 1/2" to 2"

NUMBER SIZE A B C D E Wt.90-103-01 1/2" .37 1.14 2.15 1.68 3.87 .5390-104-01 3/4" .50 1.36 2.61 1.75 3.87 .8290-105-01 1" .62 1.50 2.90 2.00 4.87 1.2590-106-01 1-1/4" .81 1.81 3.50 2.18 4.87 1.9890-107-01 1-1/2" 1.00 2.06 3.79 2.62 5.50 2.9990-108-01 2" 1.25 2.43 4.42 2.81 5.50 4.64

BRONZE UNI-BODY SATURN® BALL VALVE

1/00

® 489-100 SeriesCarbon Steel LP-Gas Ball Valve

NPT Threaded. 1/4" to 1" 2000 psig WOG; 1-1/4" to 2" 1500 psig WOG; 2-1/2" to 3" 1000 psig WOG.Cold Non-Shock. 250 psig LP-Gas. 150 psig Saturated Steam. Vacuum Service to 29 in. Hg.Federal Specification: WW-V-35C. Type: II. Composition: CS. Style: 3.

FEATURES• UL Listed for LP-Gas, natural gas and flammable liquid to 250 psig • Blow-out-proof stem design• RPTFE seats and stuffing box ring • Adjustable packing gland• Mounting pad for easy actuator mounting • Nitride corrosion protection• Investment cast components


STANDARD MATERIAL LIST1. Lever and grip Steel, zinc plated w/vinyl2. Stem packing RPTFE3. Stem bearing RPTFE4. Ball A108-12L14, chrome plated5. Seat (2) RPTFE6. Retainer A108-12L14 (1/4" to 1")

A216-WCB (1-1/4" to 3")7. Gland nut A108-12L148. Stem A108-12L149. Lever nut Steel, zinc plated

10. Body seal PTFE (1-1/4" to 3")11. Body A216-WCB

VARIATIONS AVAILABLE:489-140-01 Series with 316 SS Ball and Stem,UL Listed as noted above.


CARBON STEEL BALL VALVE

UL®

LISTED





(1-1/4” to 2”)


BRONZE FULL PORT MAIN BURNER GAS BALL VALVEw/1/8" NPT SIDE TAP

® 50-GB0 SeriesBronze Full Port Main Burner Gas Ball Valve

(GB-50 Series)

FEATURES• Chromium plated ball • Blow-out-proof stem design• RPTFE packing • Adjustable packing gland• PTFE seats • Quarter turn On-Off• Pilot side tap • Reversible handle

DESIGN CERTIFICATIONSUL LISTINGS

• Guide YRBX: LP-Gas shut-off valve. • AGA 3-88• Guide MHKZ: Gas shut-off valve for use • ANSI Z21.15

with natural and manufactured gases. •.CGA 9.1• CLIR No. 35 & CR91-002


UL®

LISTED

NUMBER SIZE A B C D E F G Wt.50-GB3-01 1/2" .50 1.11 2.25 1.68 2.85 2.27 1.00 .6450-GB4-01 3/4" .75 1.26 2.67 1.93 3.85 2.72 1.12 .8050-GB5-01 1" 1.00 1.65 3.42 2.19 4.78 3.19 1.28 1.6150-GB6-01 1-1/4" 1.25 1.87 3.86 2.37 4.78 3.56 1.62 2.6050-GB7-01 1-1/2" 1.50 2.50 4.22 2.78 5.50 4.18 1.81 3.8550-GB8-01 2" 2.00 2.48 5.02 3.15 5.50 4.90 2.18 6.57

1. Lever and grip Steel, zinc plated w/vinyl2. Stem packing RPTFE3. Stem bearing PTFE4. Ball Brass ASTM B16, chrome plated5. Seat (2) PTFE6. Gland screw Brass ASTM B167. Stem Brass ASTM B16

8. Plug PTFE coated brass9. Retainer Brass ASTM B16

10. Hex Nut Steel ASTM A563grade A, zinc plated

11. Body Brass ASTM B584UNS alloy C84400

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-A1 - 1/4" NPT Side Tap 1" to 2"-A7 - 1/4” NPT Side Tap & Tee Handle 1" to 2"-07 - 1/8" NPT Side Tap & Tee Handle 1/2" to 2"-01A- 1/8" NPT Dual Side Tap 3/4" to 2"-07A- 1/8" NPT Dual Side Tap & Tee Handle 3/4" to 2"-A1A- 1/4" NPT Dual Side Tap 1" to 2"-A7A- 1/4" NPT Dual Side Tap & Tee Handle 1" to 2"

1/00


BRONZE FULL PORT MAIN BURNER GAS BALL VALVE

® 51-GB0 SeriesBronze Main Burner Gas Ball Valve

(GB-10 Series)

FEATURES• Chromium plated ball • Blow-out-proof stem design• RPTFE packing • Adjustable packing gland• PTFE seats • Quarter turn On-Off• Available in three handle configurations

DESIGN CERTIFICATIONS• AGA 3-88• ANSI Z21.15• CLIR No. 35 & CR91-002


NUMBER SIZE A B C D E F G H I Wt.51-GB2-01 3/8" .38 1.02 2.04 1.63 .87 2.16 1.70 3.85 2.23 .5651-GB3-01 1/2" .50 1.14 2.32 1.63 .87 2.22 1.72 3.85 2.31 .6351-GB4-01 3/4" .68 1.47 2.97 2.22 1.37 3.00 2.02 4.75 2.80 1.3951-GB5-01 1" .87 1.66 3.33 2.27 1.37 3.18 2.15 4.75 3.05 1.72

1. Handle Yellow die-cast zinc2. Stem packing RPTFE3. Stem bearing PTFE4. Ball Brass ASTM B16, chrome plated5. Seat (2) PTFE6. Gland screw Brass ASTM B16

7. Stem Brass ASTM B168. Retainer Brass ASTM B169. Hex Nut Steel ASTM A563

grade A, zinc plated10. Body Brass ASTM B584

UNS alloy C84400

OPTIONS AVAILABLE:(SUFFIX) OPTION SIZES-L1 - Lever Handle W/Vinyl 3/8" to 1"-T1 - Tee Handle 3/8" to 1"

BRONZE MAIN BURNER GAS BALL VALVE

® 51-GB0 SeriesBronze Main Burner Gas Ball Valve

(GB-11 Series)

FEATURES• Chromium plated ball • Blow-out-proof stem design• RPTFE packing • Adjustable packing gland• PTFE seats • Quarter turn On-Off• Available in three handle configurations

DESIGN CERTIFICATIONS• AGA 3-88• ANSI Z21.15• CLIR No. 35 & CR91-002


NUMBER SIZE A B C D E F G H I J K Wt.51-GB30-21 3/8" .28 1.72 2.86 1.72 3.85 2.31 2.22 1.63 .87 1/2 5/8-18 .7251-GB30-22 1/2" .40 1.85 2.99 1.72 3.85 2.31 2.22 1.63 .87 1/2 3/4-16 .7851-GB30-23 5/8" .50 2.35 3.84 2.02 4.75 2.80 3.00 2.22 1.37 3/4 7/8-14 1.74

OPTIONAL “LEVER” HANDLE3/8” GB-11 (51GB3L21)1/2” GB-11 (51BGBL22)5/8” GB-11 (51GB4L23)

OPTIONAL “TEE” HANDLE3/8” GB-11 (51GB3T21)1/2” GB-11 (51GB3T22)5/8” GB-11 (51GB4T23)

1. Handle Yellow die-cast zinc2. Stem packing RPTFE3. Stem bearing PTFE4. Ball Brass ASTM B16, chrome plated5. Seat (2) PTFE6. Gland screw Brass ASTM B16

7. Stem Brass ASTM B168. Retainer Brass ASTM B169. Hex Nut Steel ASTM A563

grade A, zinc plated10. Body Brass ASTM B584

UNS alloy C84400



Top Entry

2

No SurprisesApollo’s Top Entry Ball Valves offer more. In addition to the three things everyone hascome to expect from Conbraco: high qualityproducts, competitive pricing and on timedelivery, Apollo Top Entry Valves deliver additional premiums; a broader choice ofmaterial for both internal andexternal components, moreoptional features to choosefrom, and selectable sealmaterial combinations allresulting in an expandedserviceable application range.

Fit for PurposeThese premiums can be combined to cre-ate a product uniquely tailored to customerspecifications and applications. These addi-tional options allow a valve to be selected

without compromising critical performancerequirements or operating conveniencesand without adding unnecessary featuresand the costs associated with them.

The Correct DesignThe special “V” seating design introducedthe self-adjusting seat to the floating ball

valve. This design does not rely on thebuilt-in interference of conventionalfloating ball valves. It provides auto-matic compensation for pressure,temperature and wear. As these

changes occur, the ball and seats arecontinuously snugged down into the “V”

resulting in positive leak-tight shutoff whenusing resilient seats. Maintaining a low pres-sure seal had been the most difficult condi-tion for floating ball valves, the wedge effecton the ball and seats down the “V” assures

continued low pressure sealing for the life ofthe seat.

All Apollo Top Entry Valves have an“anti-static” feature designed in. All valveconfigurations also feature blow-out proofstems as standard.

The Right ApplicationApollo’s Top Entry Valves provide simplifiedin-line maintenance in the most natural way. The valve body is allowed to act as a permanent part of the piping system.Potential leak paths are eliminated with theone piece body. Only the bonnet seal andstem seals remain to be counted. And withthe variety of bonnet gaskets and stem sealarrangements available through the selec-tion of optional features, even these threatscan be minimized.

Top Entry Valve Features . . . . . . . . . . . . . . . . . . . . . . . . 2Special Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3How to Specify Apollo Top Entry Valves . . . . . . . . . . . . 4Materials Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Flanged Series Top Entry Valves . . . . . . . . . . . . . . . . . . 6Socket Weld & NPT Series Top Entry Valves . . . . . . . . 6Buttweld Series Top Entry Valves . . . . . . . . . . . . . . . . . 7Bonnet Dimensions for Actuator Mounting . . . . . . . . . . 7Dimensions For Actuator Pad Style Mounting . . . . . . . . 8

Flanged Series Full Port Dimensional Data . . . . . . . . . . . 9Flanged Series Full Port Actuator Mounting Data . . . . . . 10Operating Torques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Extended Bonnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Fugitive Emissions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Steam Jacketed Valves . . . . . . . . . . . . . . . . . . . . . . . . . . 13Seat Performance Data . . . . . . . . . . . . . . . . . . . . . . . . . . 14Steam Charts & Application Guide . . . . . . . . . . . . . . . .15-18Flow Coefficients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Top Entry Advantages:

• Self-Adjusting Seats: Compensate for Wear & TemperatureFluctuations• Spring Loaded Low Pressure Seals• Pressure Activated Seating• Built-In Antistatic Feature• Simplified In-line Service• Minimal Potential Leak Paths

TABLE OF CONTENTS

Apollo® Top Entry Ball Valve Features

Standards Compliance(Most valves within this family of products comply with the requirements of these listed standards.)

ASME B16.5 “Pipe Flanges and Flanged Fittings”ASME B16.10 “Face to Face Dimensions of Valves” (Except Full Port Valves)ASME B16.34 “Valves – Flanged, Threaded, and Welding End.”ASME B31.1 “Power Piping”ASME B31.3 “Chemical Plant and Petroleum Refinery Piping”ASME B31.8 “Gas Transmission and Distribution Piping Systems”API 607 “Fire Test – Soft Seated Quarter Turn Valves” (Depending on Seat and Seal Selection)MSS SP-25 “Standard Marking System for Valves”MSS SP-61 “Pressure Testing of Steel Valves”MSS SP-72 “Ball Valves with Flanged of Buttweld Ends”

Customer Service 1-704-841-6000 3

Ball Valves

Apollo ANSI Class 150 Flanged

8-inch Titanium Top Entry Ball Valve

Special Applications

Oxygen Service ValvesFor this application, cleanliness is of utmost impor-tance. Apollo Top Entry Valves specified for oxygenservice (option “PO”) are subjected to rigorous prepa-ration procedures including special pre-cleaning andinspection followed by ultrasonic cleaning and moreintense inspection. All to insure that the finished valveis free of burrs and sharp edges as well as cleaned ofhydrocarbon residues and particulate matter. Oncevalves destined for oxygen service enter Conbraco’sclean room for preparation, they do not leave until theyhave been cleaned, assembled, thoroughly tested,inspected, tagged and bagged to meet customerrequirements.

All Apollo Top Entry Valves have “anti-static” fea-tures designed in. Valves for oxygen service must alsobe fitted with PTFE or RPTFE seats and packing. Whenplanning to insulate valves, consider specifying one of our extended bonnet options.

High Temperature ServiceFor any applications utilizing metal, graphite, carbongraphite, peek, carbon reinforced peek, or ceramicseats, a ball stop should be incorporated into the valvedesign (option “RS”). This option is suggested at anytemperature but it becomes a necessity above 500°F orwhen using ceramic or metal seats. The ball stop pre-vents the ball and seat from sliding down the 7° wedgewhen expansion caused by the temperature increasewidens the wedge. If the ball was permitted to slidedown the wedge, the valve would be locked tight when

“Fire-Safe” RequirementsTwo seat and several seal arrangements are available toaddress valves in applications where performance dur-ing and immediately after a fire are a concern. The #7(PTFE) and “A” (RPTFE) seat configurations offer“tested” fire-safe performance. Flexible graphite in the form of die-cut, die-formed or spiral wound gaskets areavailable for bonnet seals. Die-formed Grafoil® in various configurations provide the stem seals.

Abrasive & Erosive Services“Soft Seated” valves for abrasive services feature seatinserts completely confined by metallic components.Some designs feature inner and outer seat supportrings, where the inner ring helps shield the seat insertfrom abrasives in the service. Other designs feature onepiece seatholders which completely confine the seatinsert and provide the same function in protecting thesoft seat from abrasive particles in the flow stream.

In addition to the seat configuration options, resilientand rigid seat materials are available. The rigid seatchoices include carbon-graphite, ceramic, peek, andcarbon reinforced peek. The seats and the ball are bothproduced from ceramic in the one case. Any of theseseats provide improved resistance to abrasion and ero-sion and additionally extend the potential service rangeto 1000°F.

For steam services, the #5 seat, a RPTFE contain-ing 55% bronze and 5% molybdenum disulfide, is anexcellent choice as is the #4 carbon-graphite seat.

Valves for Chlorine ServiceValves intended for service in dry chlorine require specific alloy selections, design features, cleaning andtesting procedures. In accordance with the guidelines established by “The Chlorine Institute”, Pamphlet 6-13thEdition (April 1993), Hastelloy trimmed carbon steelvalves (model numbers starting with “CH”) are suggest-ed, and M35-1 trimmed carbon steel valves (model num-bers beginning “CM”) are the alternative for dry chlorine.All Hastelloy or M35-1 valves are also available, how-ever, stainless steel valves or components are not recommended.

Selecting the required “HO” feature insures a valvethat has been vented, cleaned, and tested to complywith the requirements of The Chlorine Institute Pamplet 6.


Top Entry

4

BODY MATERIALA - Alloy 20B - CF3M SS

(Flanged )C - Carbon SteelF - InconelH - Hastelloy CM - M35-1N - NickelS - 316 SST - Titanium

TRIM MATERIALA - Alloy 20B - 316L SSC - Carbon SteelD - Hastelloy C Stem M35-1

BallE - 410 SSF - InconelH - Hastelloy CM - M35-1 (Monel)N - NickelS - 316 SST - Titanium

0 0 - 0 0 0 - 0 0

END CONFIGURATION AND

PRESSURE CLASSB - 150# FlangedC - 300# FlangedD - 300# NPTE - 150# FP FlangeF - 300# FP FangeG - 300# NPT x Soc. WeldH - 600# NPTJ - 600# Socket WeldK - 600# FlangedL - 300# FP NPTM - 300# FP Soc. WeldN - 300# Socket WeldP - 300# ButtweldQ - 600# NPT x Soc. WeldR - 300# FLG x ButtweldS - 300# RTJ FlangesT - 600# FP Socket WeldU - 600# FP FlangeW- 600# ButtweldY - 300# FP NPT x Socket Weld3 - 300# FP Buttweld4 - 600# FP NPT6 - 600# FP NPT x Socket Weld7 - 600# FP Buttweld9 - 900# Flange

SEAT (FIGURES ON PAGE 15)1 - TFE (Figure 1)2 - RTFE (Figure 1)3 - RTFE Seat (Figure 2)4 - Carbon Graphite -750°F max.

(Figure 1)5 - 55% Bronze, 5% Moly, (Figure 2)6 - UHMWPE (Figure 2)7 - API-607 Certified (TFE Seat, TFE

O-ring, Grafoil® Seal & Pkgs.)8 - PEEK (Figure 2)9 - Ceramic A - API-607 Certified (RTFE Seat,

TFE O-ring, Grafoil® Seal &Pkgs.)

B - 30% Carbon Reinforced PEEK (Figure 2)

C - PFA (Figure 2)D - SRTFE, 60% SS, 40% TFE by

weight (50% SS Min) (Figure 2)F - CRTFE (Figure 1)G - PCTFE (Figure1)H - High Temp Graphite-1000°F max.

(Figure 1)K - Stellite Ball & Seats (Figure 4)M - Malcomized 316 SS Ball & Seats

(Figure 4)U - UHMWPE (Figure 1)

SIZE

3 - 1/2"

4 - 3/4"

5 - 1"

7 - 1-1/2"

8 - 2"

0 - 3"

A - 4"

C - 6"

E - 8"

G - 10"

H - 12"

AR - Actuator Ready

BO - Grafoil® Seals & Packings

BN - TFE Spiralwound Bonnet Gasket

BS - Grafoil® Spiral Wound Bonnet

Gasket & Grafoil® Packings

CH - Clamp-On Steam Jacket - Stainless

Steel

CJ - Clamp-On Steam Jacket - Carbon Steel

CL - Cam-Lock Handle

EB - Extended Bonnet

EO - Round Handle

FC - Live Loaded Fugitive Emission w/

Double RPTFE Chevron Packings

FG - Fugitive Emission Bonnet with EVSP®

9000 Graphite Stem Packing

FL - Fugitive Emission Bonnet with Double

RPTFE Stem Packing

FO - Full Jacketed w/Oversize Flanges

FP - Live Loaded Fugitive Emission w/Double

EVSP Packings

GO - 2 1/4" Stem Extension

HH - Vented Body

HO - Vented Body & Cleaned for

Chlorine Service

HP - Vented Body & Cleaned for Hydrogen

Peroxide Service

MG - Gear Operator

MT - 2 Position Lock Plate

for Standard Bonnet

MU - 2 Position Lock Plate for Extended Bonnet

NC - NACE Certified Trim

OL - Oval Locking Handle

OO - RPTFE Seals & Packings

OM - RPTFE Bonnet Gasket & UHMWPE

Packings

PJ - Partial Steam Jacket

PO - Cleaned for Oxygen Service

PP - Cleaned for Industrial Gases

RS - Welded Ball Stop with Safety Cap

TP - Two Position Sliding Latch Lock Lever

ZO - PTFE Seals & Packings

Note: Optional Features may be used alone or in combination (simply added in alphabetical order), however not allcombinations are available on all valves. This is a very limited list of the available options. Contact the factory for specificrequirements and availability.

* MG Is Generic for Gear Operators. Contact Factory or Price Book For Specific Application and Correct Part Number.® EVSP is a registered trademark of Garlock.

OPTIONAL FEATURES

Select the valve model number

*

How To Specify Apollo® Top Entry Ball Valves


Ball Valves

External Designation A C H M N S T

Seat Ring(s) ASTM B473-CB-3 ASTM A269-316 or ASTM B574-C276 ASTM B164-400 or ASTM B160-200 ASTM A269- 316 ASTM B348-Gr 2(from bar, tube or pipe ASTM A276-316 or ASTM B165-400 ASTM B161- 200 ASTM A276-316 ordepending on availability) ASTM A312-316 ASTM A312-316

Internal Spring (1 or 2 seats) Inconel X-750 ASTM A313-Type 316 Inconel X-750 Inconel X-750 Inconel X-750 ASTM A313-Type 316 Ti-6AL-4V

Internal Spring Inconel X-750 Inconel X-750 Inconel X-750 Inconel X-750 Inconel X-750 Inconel X-750 Ti-6AL-4V(3, 4, 5, 6, 7, 8, 9, A or Z seats)

Packing Gland 316 Stainless Steel

Packing Jam Nut 18-8 Stainless Steel

Lever Assembly - (1/2 - 2") 304 Stainless Steel w/Vinyl Grip

Lever Assembly - (3" - 8") Stainless Steel Wrench Head and Pipe

Grounding Spring 18-8 Stainless Steel

Studs ASTM A193-B8M

Nuts ASTM A194-Gr.8

Capscrews ASTM A193-B8 ASTM A193-B7 ASTM A193-B8 ASTM A193-B8 ASTM A193-B8 ASTM A193-B8 ASTM A193-B8

Material Designation A C H M N S T

Description Alloy 20 Carbon Steel Hastelloy C M35-1 Nickel (200) Stainless Steel Titanium

Body ASTM A351-CN7M ASTM A216-WCB ASTM A494-CW12MW ASTM A494-M35-1 ASTM A494-CZ100 ASTM A351-CF8M ASTM B367-Gr C3(Flanged ends)

Body ASTM A351-CN7M ASTM A216-WCB ASTM A494-CW12MW ASTM A494-M35-1 ASTM A494-CZ100 ASTM A351-CF3M ASTM B367-Gr C3(Buttweld, Socket weld, and screwed ends)

Bonnet ASTM A351-CN7M ASTM A216-WCB ASTM A494-CW12MW ASTM A494-M35-1 ASTM A494-CZ100 ASTM A351-CF8M ASTM B367-Gr C3

Material Designation A H M N S T

Description Alloy 20 Hastelloy C M35-1 Nickel (200) Stainless Steel Titanium

Ball ASTM A351-CN7M or ASTM A494-CW12MW or ASTM A494-M35-1 or ASTM A494-CZ100 or ASTM A351-CF8M or ASTM B367-Gr C3 or ASTM B473-CB-3 ASTM B574-C276 ASTM B164-K400 ASTM B160-200 ASTM A479-316 ASTM B348-Gr 4-5

Stem ASTM B473-CB-3* ASTM B574-C276 ASTM B164-K400 ASTM B160-200 ASTM A276-316* ASTM B348-Gr 4-5

* Denotes Hard Chrome Plated

Seat Designation 1 2 3 4 5 D 6

Seat PTFE RPTFE RPTFE Carbon Graphite 55% Bronze, 5% Moly 60% Stainless UHMWPEFilled PTFE Filled PTFE

Seat O-ring - - - - - - -

Stem Packing PTFE RPTFE Grafoil® Grafoil® Grafoil® Grafoil® Grafoil®

Bonnet Gasket PTFE RPTFE Grafoil® (150-300) Grafoil® (150-300) Grafoil® (150-300) Grafoil® (150-300) Grafoil® (150-300) Spiral Wound Spiral Wound Spiral Wound Spiral Wound Spiral WoundGrafoil® (600) Grafoil® (600) Grafoil® (600) Grafoil® (600) Grafoil® (600)

Default Suffix ZO1 001 BO1 (150-300) BO1 (150-300) BO1 (150-300) BO1 (150-300) BO1 (150-300)(All Classes) (All Classes) BS1 (600) BS1 (600) BS1 (600) BS1 (600) BS1 (600)

Seat Designation U 7 8 9 A B H

Seat UHMWPE API 607 - PTFE Unfilled PEEK CERAMIC API 607 RPTFE Carbon Reinforced High Temp. Fire Seat (Seats & Ball) Fire Seat PEEK Graphite

Seat O-ring - PTFE - - PTFE - -

Stem Packing Grafoil® Grafoil® Grafoil® Grafoil® Grafoil® Grafoil® Grafoil®

Bonnet Gasket Grafoil® (150-300) Grafoil® Grafoil® (150-300) Grafoil® (150-300) Grafoil® Grafoil® (150-300) Grafoil® (150-300)Spiral Wound Spiral Wound Spiral Wound Spiral Wound SpiralwoundGrafoil® (600) Grafoil® (600) Grafoil® (600) Grafoil® (600) Graphoil® (600)

Default Suffix BO1 (150-300) BO1 BO1 (150-300) BO1 (150-300) BO1 BO1 (150-300) BO1 (150-300)BS1 (600) BSI (600) BS1 (600) BS1 (600) BS1 (600)

Shell (External) Material Selection

Corresponding Hardware Materials

Trim (Internal) Material Selection

Seat & Seals Material Selection


Top Entry

6

NPT Valve Dimensions

ANSI 300 Class NPT Top Entry Valves

Size A B C D E F1/2" 0.81 2.15 4.29 3.48 5.15 1.703/4" 0.81 1.96 3.91 3.48 5.15 1.701" 0.81 1.96 3.91 3.48 5.15 1.701-1/2" 1.17 2.49 4.98 4.17 5.94 1.962" 1.50 2.86 5.72 4.74 7.87 2.223" 2.25 4.15 8.29 6.41 19.12 2.93

ANSI 600 Class NPT Top Entry Valves

Size A B C D E F1/2" 0.81 2.37 4.73 4.93 8.50 1.923/4" 0.81 2.18 4.35 4.93 8.50 1.921" 0.81 2.18 4.35 4.93 8.50 1.921-1/2" 1.17 2.62 5.23 5.77 12.50 2.142" 1.50 2.99 5.98 6.65 14.75 2.54

Socket Weld Valve Dimensions

ANSI 300 Class Socket Weld Top Entry Valves

Size A B C D E F G1/2" 0.81 2.15 4.29 3.48 5.15 1.70 0.383/4" 0.81 1.96 3.91 3.48 5.15 1.70 0.561" 0.81 1.96 3.91 3.48 5.15 1.70 0.501-1/2" 1.17 2.49 4.98 4.17 5.94 1.96 0.552" 1.50 2.86 5.72 4.74 7.87 2.22 0.623" 2.25 4.15 8.29 6.41 19.12 2.93 1.00

ANSI 600 Class Socket Weld Top Entry Valves

Size A B C D E F G1/2" 0.81 2.37 4.73 4.93 8.50 1.92 0.383/4" 0.81 2.18 4.35 4.93 8.50 1.92 0.561" 0.81 2.18 4.35 4.93 8.50 1.92 0.501-1/2" 1.17 2.62 5.23 5.77 12.50 2.14 0.552" 1.50 2.99 5.98 6.59 14.75 2.54 0.62

Flanged Series Top EntryBall Valves

Socket Weld & NPT SeriesTop Entry Valves

Flanged Valve Dimensions

ANSI 150 Class Flanged Top Entry Valves

Size A B C D E F G H J1/2" 0.81 2.85 5.69 3.48 5.15 1.70 2.38 0.62 43/4" 0.81 2.31 4.62 3.54 5.15 1.76 2.75 0.62 41" 0.81 2.50 5.00 3.48 5.15 1.70 3.12 0.62 41-1/2" 1.17 3.25 6.50 4.17 5.94 1.96 3.87 0.62 42" 1.50 3.50 7.00 4.74 7.87 2.22 4.75 0.75 43" 2.25 4.00 8.00 6.41 19.12 2.93 6.00 0.75 44" 3.00 4.50 9.00 7.55 19.50 3.32 7.50 0.75 8*6"** 4.50 7.75 15.50 10.06 36.00 4.97 9.50 0.87 88"** 6.00 9.00 18.00 14.39 47.00 6.51 11.75 0.87 810"** 7.50 10.50 21.00 15.50 NA NA 14.25 1.00 12* Top 2 holes in each flange are tapped 5/8-11 UNC-2B** Gear Operator or Actuation Recommended.


Size A B C D E F G H J1/2" 0.81 2.85 5.69 3.48 5.15 1.70 2.62 0.62 43/4" 0.81 3.00 6.00 3.63 5.15 1.86 3.25 0.75 41" 0.81 3.25 6.50 3.48 5.15 1.70 3.50 0.75 41 1/2" 1.17 3.75 7.50 4.17 5.94 1.96 4.50 0.88 42" 1.50 4.25 8.50 4.74 7.87 2.22 5.00 0.75 83" 2.25 5.56 11.13 6.41 19.12 2.93 6.63 0.88 84" 3.00 6.00 12.00 7.55 19.50 3.32 7.88 0.88 86" ** 4.50 7.94 15.87 10.06 36.00 4.97 10.63 0.88 128" ** 6.00 9.87 19.75 14.39 47.00 6.51 13.00 1.00 1212”** 9.00 12.75 25.50 18.75 NA NA 17.75 1.25 16** Top 6 holes in each flange are tapped 1 1/8-8UN-2B.** Gear Operator or Actuation Recommended.


Size A B C D E F G H J1/2" 0.81 3.25 6.50 4.93 8.50 1.92 2.62 .62 43/4" 0.81 3.75 7.50 5.17 8.50 2.18 3.25 0.75 41" 0.81 4.25 8.50 5.23 8.50 2.21 3.50 0.75 41-1/2" 1.17 4.75 9.50 6.00 12.50 2.36 4.50 0.88 42" 1.50 5.75 11.50 7.02 14.75 2.97 5.00 0.75 83" 2.25 7.00 14.00 8.64 19.12 3.47 6.63 0.88 84" ** 3.00 8.50 17.00 9.95 19.12 4.15 8.50 1.00 86" ** 4.50 11.00 22.00 NA NA 5.78 11.50 1.12 12** Gear Operator or Actuation Recommended.


Ball Valves

Buttweld Valve Dimensions

ANSI 300 Class Buttweld* Top EntryValves

Size A B C D E F1/2" 0.81 2.75 5.50 3.48 5.15 1.703/4" 0.81 3.00 6.00 3.48 5.15 1.701" 0.81 3.25 6.50 3.66 5.15 1.881-1/2" 1.17 3.75 7.50 4.22 5.94 2.012" 1.50 4.25 8.50 5.02 7.87 2.503" 2.25 5.56 11.13 6.41 19.12 2.934" 3.00 6.00 12.00 7.55 19.50 3.326"** 4.50 7.94 15.88 10.06 36.00 4.978"** 6.00 10.25 20.50 14.39 47.00 6.51* Available in Schedule 10, 40 and 80 where appropriate.** Gear Operator or Actuation Recommended.

ANSI 600 Class Buttweld* Top EntryValves

Size A B C D E F1/2" 0.81 2.75 5.50 4.93 8.50 1.923/4" 0.81 3.75 7.50 5.17 8.50 2.161" 0.81 4.25 8.50 5.23 8.50 2.221 1/2" 1.17 4.75 9.50 6.01 12.50 2.382" 1.50 5.75 11.50 7.11 14.75 3.003" 2.25 7.00 14.00 9.34 19.50 NA4" ** 3.00 8.50 17.00 10.98 36.00 NA6" ** 4.50 11.00 22.00 NA NA NA* Available in Schedule 40 and 80 where appropriate.** Gear Operator or Actuation Recommended.

ANSI 150/300 Class Socket Weld, NPT & Buttweld Valves

Size Fig. No. A B C D E F G H J K L M N1/2” 1 1.30 1.00 .77 .500 2.125 1.062 1.812 .906 .292 .36 1.00 NA 5/16-183/4” 1 1.30 1.00 .77 .500 2.125 1.062 1.812 .906 .292 .36 1.00 NA 5/16-181” 1 1.30 1.00 .77 .500 2.125 1.062 1.812 .906 .292 .36 1.00 NA 5/16-181-1/2” 1 2.04 1.68 .99 .625 2.812 1.406 2.250 1.125 .417 .36 1.25 NA 3/8-162” 1 2.39 1.91 1.06 .750 3.375 1.687 2.750 1.375 .482 .52 1.50 NA 1/2-133” 1 3.27 2.66 1.55 1.125 4.000 2.000 4.875 2.437 .730 .72 2.00 NA 5/8-114” 3 4.66 4.11 2.24 1.500 6.375 3.188 3.750 1.875 .970 NA NA 6.00 9/16-126” 3 4.88 4.15 1.96 2.000 9.750 4.875 4.500 2.250 1.380 NA NA NA 3/4-108” 3 5.77 4.79 2.56 2.36 12.06 6.031 7.375 3.688 1.755 NA NA 7.94 1-8

ANSI 600 Class Socket Weld, NPT, & Buttweld Valves

1/2” 2 2.48 2.06 .76 .625 2.125 1.062 1.816 .908 .412 .36 1.00 NA 7/16-183/4” 2 2.48 2.06 .76 .625 2.125 1.062 1.816 .908 .412 .36 1.00 NA 7/16-181” 2 2.48 2.06 .76 .625 2.125 1.062 1.816 .908 .412 .36 1.00 NA 7/16-181-1/2” 3 3.48 3.06 1.03 .750 2.814 1.407 2.250 1.125 .475 .36 1.25 NA 7/16-142” 3 3.95 3.47 1.03 .875 3.370 1.685 2.750 1.375 .535 .52 1.50 NA 1/2-13

Buttweld Series Top EntryBall Valves

Bonnet Dimensions For Actuator Mounting


Top Entry

8

Class 600 Buttweld

3" 4" 6"A 2.50 2.90 4.19B 5.96 7.36 7.91C 1.54 2.25 1.34D 1.125 1.500 2.000E 8.620 11.000 15.000F 4.310 5.500 7.500G 2.330 2.800 4.160H 1.150 1.400 2.130J 0.730 0.970 1.380K 7.56 9.38 12.88L 1/2-13 1/2-13 3/4-10M 0.61 0.75 1.00N 8.45 10.25 12.10

Class 600 Flanged Valves

3/4" 1" 1-1/2" 2" 3" 4" 6"A 6.32 7.25 8.06 9.94 12.25 15.00 19.62B 3.16 3.63 4.03 4.97 6.13 7.50 9.81C 2.38 2.38 2.75 3.50 4.75 5.50 7.00D 1.19 1.19 1.38 1.75 2.38 2.75 3.50E 2.21 2.15 2.83 3.54 4.18 4.88 4.97F 4.65 4.71 6.08 6.92 8.43 10.38 12.09G 2.44 2.56 3.25 3.38 4.25 5.50 7.12H 0.76 0.76 1.27 1.03 1.54 2.25 1.34J 3/8-16 3/8-16 1/2-13 1/2-13 1/2-13 1/2-13 3/4-10K 0.47 0.47 0.66 0.66 0.66 0.75 1.00 L 0.412 0.412 0.475 0.535 0.730 0.970 1.380


3/4" 1" 1-1/2" 2" 3" 4" 6" 8"A 5.31 5.75 6.63 7.56 9.88 10.69 14.31 18.06B 2.66 2.88 3.31 3.78 4.94 5.34 7.15 9.03C 1.75 1.75 1.75 2.25 3.50 4.00 4.00 5.00D 0.88 0.88 0.88 1.13 1.75 2.00 2.00 2.50E 0.70 0.62 0.81 1.23 1.95 2.83 3.47 4.53F 3.15 3.00 4.00 4.61 6.20 7.98 9.85 12.28G 2.45 2.38 3.19 3.38 4.25 5.13 6.38 7.75H 0.77 0.77 0.99 1.06 1.55 2.24 1.96 2.56J 5/16-18 5/16-18 5/16-18 5/16-18 3/8-16 7/16-14 7/16-14 1/2-13K 0.48 0.48 0.47 0.47 0.56 0.66 0.50 0.66 L 0.292 0.292 0.417 0.482 0.730 0.970 1.380 1.755


3/4" 1" 1-1/2" 2" 3" 4" 6" 8" 10"A 4.06 4.43 5.75 6.24 7.18 8.19 14.25 16.75 19.75B 2.03 2.21 2.88 3.12 3.59 4.09 7.13 8.38 9.88C 1.75 1.75 1.75 2.25 3.50 4.00 4.00 5.00 7.00D 0.88 0.88 0.88 1.13 1.75 2.00 2.00 2.50 3.50E 0.70 0.62 1.37 1.48 2.32 3.33 4.22 5.28 6.50F 3.06 3.00 4.00 4.61 6.20 7.98 9.85 12.28 15.50G 2.36 2.38 2.63 3.13 3.88 4.63 5.63 7.00 9.00H 0.77 0.77 0.99 1.06 1.55 2.24 1.96 2.56 2.90J 5/16-18 5/16-18 5/16-18 5/16-18 3/8-16 7/16-14 7/16-14 1/2-13 3/4-10K 0.48 0.48 0.47 0.47 0.56 0.66 0.50 0.66 1.25L 0.292 0.292 0.417 0.482 0.730 0.970 1.380 1.755 2.030

Dimensions For Actuator Pad Style Mounting

9

Ball Valves


Flanged Series Top EntryFull Port Ball ValveDimensional Data

ANSI 600 Class Full Port Flanged Top Entry Valves

Size A B C D E F G H J1” 1.17 5.00 10.00 6.06 12.50 2.40 3.50 .75 41-1/2” 1.50 6.25 12.50 7.15 14.75 3.06 4.50 .87 42” 2.25 6.50 13.00 9.76 19.12 3.70 5.00 .75 83” 3.00 8.75 17.50 11.45 19.50 4.48 6.63 .87 84” 4.50 10.00 20.00 12.44 NA 6.13 8.50 1.00 86” 6.00 13.00 26.00 15.28 NA 7.50 11.50 1.12 128” 8.00 15.62 31.25 18.58 NA 11.42 13.75 1.25 12*• Top 2 Holes in each flange are tapped 1-1/8 UN-2B


Size A B C D E F G H J1” 1.17 3.50 7.00 4.27 5.94 2.05 3.12 .62 41-1/2” 1.50 4.37 8.75 5.05 7.87 2.51 3.87 .62 42” 2.25 5.25 10.50 7.61 19.12 3.23 4.75 .62 43” 3.00 6.75 13.50 9.33 19.50 3.80 6.00 .75 44” 4.50 8.50 17.00 12.32 36.00 5.39 7.50 .75 86” 6.00 10.75 21.50 15.57 43.00 6.67 9.50 .87 88” 8.00 12.25 24.50 18.32 NA 9.39 11.75 .87 8*• Top 2 Holes in each flange are tapped 3/4-10 UNC-2B


Size A B C D E F G H J1” 1.17 3.75 7.50 4.27 5.94 2.08 3.50 .75 41-1/2” 1.50 4.75 9.50 5.05 7.87 2.55 4.50 .87 42” 2.25 5.56 11.13 7.61 19.12 3.27 5.00 .75 83” 3.00 7.62 15.25 9.33 19.50 3.91 6.63 .87 84” 4.50 9.00 18.00 12.32 36.00 5.45 7.88 .87 86” 6.00 11.00 22.00 15.57 43.00 6.70 10.63 .87 128” 8.00 13.50 27.00 18.32 NA 9.54 13.00 1.00 12*• Top 2 Holes in each flange are tapped 7/8-9 UNC-2B

Flanged Series Top Entry Full Port Ball Valves

Actuator Mounting Data

10

Top Entry



Size A B C D E EE F G GG H J K L M1” 6.44 3.22 1.75 .88 1.71 NA 4.09 2.38 NA .99 5/16-18 .48 .417 .6251-1/2” 8.06 4.03 1.75 .88 2.27 NA 4.90 2.63 NA 1.06 5/16-18 .47 .482 .7502” 9.68 4.84 2.25 1.13 3.37 NA 6.50 3.13 NA 1.55 5/16-18 .47 .730 1.1253” 12.48 6.24 3.50 1.75 4.58 NA 8.46 3.88 NA 2.24 3/8-16 .56 .970 1.5004” 15.81 7.91 4.00 2.00 5.23 NA 10.27 5.04 NA 1.96 7/16-14 .66 1.380 2.0006” 20.25 10.13 4.00 2.00 6.13 2.73 12.29 6.16 9.56 1.00 7/16-14 .66 Fig. 1 Fig. 18” NA NA NA NA NA 5.77 NA NA 12.37 NA NA NA Fig 2 Fig. 210” 19.75 8.88 7.00 3.50 6.50 NA 15.50 9.00 NA 2.90 3/4-10 1.25 2.030 2.933


1” 6.69 3.35 1.75 .88 1.74 NA 4.12 2.38 NA .99 5/16-18 .48 .417 .6251-1/2” 8.63 4.31 1.75 .88 1.75 NA 4.94 3.19 NA 1.06 5/16-18 .47 .482 .7502” 9.90 4.95 2.25 1.13 3.16 NA 6.54 3.38 NA 1.55 5/16-18 .47 .730 1.1253” 13.68 6.84 3.50 1.75 4.32 NA 8.57 4.25 NA 2.24 3/8-16 .56 .970 1.5004” 16.50 8.25 4.00 2.00 5.20 NA 10.33 5.13 NA 1.96 7/16-14 .66 1.380 2.0006” 20.38 10.19 4.00 2.00 5.41 2.73 12.32 6.91 9.59 1.00 7/16-14 .66 Fig. 1 Fig. 18” NA NA NA NA NA 5.77 NA NA 12.52 NA NA NA Fig. 2 Fig. 2


1” 8.75 4.38 2.38 1.19 3.56 NA 6.12 2.56 NA 1.27 3/8-16 .47 .475 .7501-1/2” 11.06 5.53 2.75 1.38 3.75 NA 7.00 3.25 NA 1.03 1/2-13 .66 .535 .8752” 11.38 5.69 3.50 1.75 5.20 NA 8.66 3.46 NA 1.54 1/2-13 .66 .730 1.1253” 15.56 7.78 4.75 2.38 6.45 NA 10.70 4.25 NA 2.25 1/2-13 .66 .970 1.5004” 17.75 8.88 5.50 2.75 6.94 NA 12.44 5.50 NA 1.34 1/2-13 .75 1.380 2.0006” 23.44 11.72 7.00 3.50 8.21 NA 15.33 7.12 NA 2.56 3/4-10 1.00 1.380 2.3608” NA NA NA NA NA 5.77 NA NA 12.78 NA NA NA Fig. 2 Fig. 2

Dimensions For Actuator Pad Style Mounting


Ball Valves

There are several elements involved in developing anappropriate “in-service” valve operating torque. Selection ofthe basic valve torque constant, shown at the left establish-es the nominal valve torque based on the valve size, speci-fied valve seat and the approximate working pressure.

Armed with the nominal valve operating torque, adjust-ments are now made to account for individual serviceconditions. These factors are selected from the table atthe lower left. They are additive, or combined in seriesand used to arrive at the “in-service” torque.

Torque Adjustment Factors

Provision Condition Additional Factor

Type of ON/OFF Service 0Operation Modulating 0.25

Process Media Liquid, Clean Particle Free 0Liquid, Dirty, Slurry, Raw Water 0.3 to 0.8Liquid, Black Liquor, Lime Slurry 0.8Liquid, Oil, Lubricating -0.3Liquid, Viscous, Molasses 0.3Gas, Clean & Wet, Saturated Steam0Gas, Dry, Superheated Steam 0.3 to 0.5Gas, Dirty, Air Slurry, Natural Gas 0.5 to 1Oxygen, Chlorine 0.5

Frequency of Operation Once per Day or More 0Once per Day to Once per Week 0.2Once per Week to Once per Month 0.5Once per Month or Less 1

Example:Selected Valve: 3" 150 w/#6 seat (Model: CS-C60-BO1)

Torque Constant: 1250 in-lbsService Factors:

ON/OFF Service 0.0Clean Dry Air 0.3Weekly Operation 0.2Net Service Factor 0.5

“In Service” Valve Torque: 1250 x (1 + 0.5) = 1875 in-lbsThis is the valve torque used to select an actuator.

Features:• Extended bonnets for Apollo® Top Entry Ball Valves

are available for sizes 1/2" through 8" in classes 150and 300. Extended bonnets are standard for all class600 valves.

• These bonnets provide excellent performance in hightemperature or semi cryogenic applications.

• This bonnet design places the stem seals further awayfrom the process flow thereby maintaining tempera-tures closer to ambient.

• Insulation can be applied to the bonnet reducing thechance of disturbance as would be caused by a stem extension. If and when stem leakage occursit can be immediately observed and corrective action taken without insulation removal.

• A valuable feature of the Extended Bonnet is that it is field retrofitable. In addition to being able to ordervalves with several bonnet styles direct from the factory, kits are available that are pre-assembled with the stem, bonnet, packings, glands and jam nut installed and properly torqued for dependableperformance. Contact the factory for kit part numbersfor any specific valve or application.

Materials of Construction:Extended bonnets are available in the same broadselection of materials of construction as those illustrated on page 5 for the bonnet, stem, stem packings, packing gland, nuts and body seals.

Class 150 & 300 Extended BonnetsSize A B C3/4" 2.55 2.25 0.771" 2.55 2.25 0.77

1-1/2" 3.54 3.18 0.992" 4.14 3.66 1.063" 5.27 4.66 1.554" 6.66 6.11 2.246" 6.88 6.15 1.968" 7.77 6.79 2.56

Apollo® Top Entry Valve Operating Torques

Extended Bonnets

Torque Constants for Apollo®

Top Entry Ball Valves****Seat Valve Differential Pressures (psig)

Options Size 100 285 500 740 1480*1 *7 1/2 thru 1" 85 110 140 180 290

1-1/2" 205 260 330 415 6602 A 2" 350 430 550 735 1,2003 C 3" 950 1,250 1,650 2,000 3,200

4" 2,000 2,500 3,300 4,100 6,5005 D 6"** 5,300 6,700 8,200 11,400 18,0006 Z 8"** 11,000 14,000 18,500 25,000 36,000

10"** 18,500 22,000 30,000 40,000 62,000

Seat Valve Differential Pressures (psig) Options Size 100 285 500 740 1480

1/2 thru 1" 115 160 210 260 4504 1-1/2" 270 370 480 590 1,0008 2" 475 650 860 1,050 1,750***9 3" 1,250 1,850 2,400 2,950 4,900

4"** 2,700 3,700 4,900 5,900 10,000B 6"** 7,410 10,100 13,400 16,400 25,300

8"** 15,000 20,000 26,000 34,500 56,00010"** 25,000 32,000 45,000 60,000 96,000

*Reduce torque by 30% for PTFE seats**Gear operator or actuation recommended***Increase torque by 10% for Ceramic seats****For full port figures, use one valve size larger


Top Entry

12

Following a detailed testingprogram it has been found thatthe double stack of RPTFEChevron style packings clearlyoutperformedthe other con-tenders evaluat-ed. In applica-tions where thismaterial isacceptable, itwould be thehands-downchoice.However, whenresistance to high temperaturesis a must, such as in a valverequiring fire-safe performance,then the Grafoil® packings mustbe considered.

With any of the styles ofgrafoil packings tested it isreasonable to expect that overthe anticipated life of the pack-ing (100,000 cycles) two (2)packing adjustments will berequired. From the testing, thefirst adjustment could be antic-ipated around the 20,000

cycle point and the secondsome time after the 60,000cycle mark. The primary offer-ing in Grafoil® fugitive emis-

sions stylepackings forApollo® TopEntry BallValves will bethe doublestack arrange-ment providedby Garlock®

under the tradename EVSP.

The results are presentedhere in 5000 cycle increments.Measurements were takenmore frequently and thoseother data points showed noevidence of any trends in thegrowth of a leak from a minorstatus to one requiring adjust-ment. Through process moni-toring, statistical data can beused to establish preventivemaintenance schedules showing packing adjustment intervals.

Leakage Rate in PPM Methane

Cycle Count Double Stack Double StackRPTFE Chevrons Grafoil®

5000 0 010,000 0 015,000 0 020,000 4 125,000 3 42*30,000 4 035,000 18 040,000 14 045,000 13 250,000 3 355,000 4 360,000 8 365,000 14 470,000 30 92*75,000 24 080,000 24 085,000 23 290,000 52* 1195,000 0 0100,000 0 0

*Indicates a packing adjustment was made.Grafoil® is a registered trademark of Union Carbide.Garlock® is a registered trademark of Coltec Industries.

Fugitive Emissions Stem Seals

Fugitive Emisions Bonnet Dimension

Features:• Two types of the Fugitive Emissions Bonnet are available. The first

type intended for manual operation is not live loaded. Testing hasshown that live loading only becomes necessary in high cycle appli-cations. This leads to the second type, the live loaded version. Thissecond type not only is more appropriate for unattended automatedoperations and high cycle applications, it is also well suited for appli-cations involving thermal cycling.

• Two styles of packings are available for the Fugitive Emissions bon-net. The primary offering is a double stack of RPTFE Chevrons.The second option is a specially contoured double stack of “DieFormed” graphoil rings.

• The lower, primary packing stack is pressure activated as well asmechanically loaded. The upper packing stack acts as back-upseals in the case of primary seal failure. A purge port is availablebetween the two stacks for the purpose of detecting primary sealleakage.

• One of the most valuable features of the Fugitive Emissions Bonnetis that it is field retrofitable to existing installations. In addition tobeing able to order Top Entry valves with any of three bonnet stylesdirect from the factory, kits are available that are pre-assembledwith the stem, bonnet, packings, glands and jam nut installed andproperly torqued for dependable performance. In the case wherethe service or regulations change and a design upgrade is required,the Top Entry Ball valve is designed to accomodate these changes.Contact the factory for kit part numbers for any specific valve orapplication.

Materials of Construction:Extended bonnets are available in the same materials of constructionas those illustrated on page 5 for the bonnet, stem, stem packings,packing gland, nuts and body seals.

Class 150 & 300 ValvesLIVE LOADED FUGITIVE EMISSIONS BONNET

3/4" 1" 1-1/2" 2" 3" 4" 6"A 3.41 3.41 3.90 5.20 6.31 7.37 8.03B 3.11 3.11 3.54 4.72 5.70 6.80 7.30C 0.98 0.98 0.85 1.35 1.47 2.27 1.30

Class 150 & 300 ValvesFUGITIVE EMISSIONS BONNET

3/4" 1" 1-1/2" 2" 3" 4" 6"A 2.55 2.55 3.54 4.14 5.27 6.66 6.88B 2.25 2.25 3.18 3.66 4.66 6.11 6.15C 0.77 0.77 0.99 1.06 1.55 2.24 1.96

Class 600 ValvesLIVE LOADED FUGITIVE EMISSIONS BONNET

3/4" 1" 1-1/2" 2"A 3.27 3.27 4.54 5.03B 2.85 2.85 4.12 4.55C 0.99 0.99 1.04 1.10


Ball Valves

SConbraco’s Apollo® Top Entry Ball Valves are ideally suitedfor jacketed applications. The top entry concept allows for con-tinued access to stem packings and valve internals for ease ofmaintenance without disturbing the jacket itself or removingthe valve from the pipeline.

Partial jacketing (Option “PJ”) may be used on standardvalves. Partial jacketing is applied just to the center section ofthe valve and does not incorporate the neck area or flanges ofthe valve. It is generally specified to allow the use of standardflanges and retain conventional flange bolting. Fully jacketed,standard flange valves have modified flanges with blindtapped stud holes in place of the ordinary through holes.

Welded full jacketing may be applied to valves with standardflanges (Option “FS”) or oversize flanges (Option “FO”).Valves and jacketing can be supplied in a variety of materials.Common materials are stainless valves with stainless jackets,but exotic combinations such as Alloy 20 valves with carbonsteel flanges and carbon steel jacketing have been supplied to meet the performance and cost requirements for specificapplications.

Clamp-on jacketing (Option “CJ”) offers flexibility not availablein the other configurations. Clamp-on jacketing can be appliedto valves already in service, or can be removed and reinstalledon a replacement valve or another similar valve in anotherapplication. Clamp-on jackets can be supplied as a weldmentor in cast aluminum. A heat transfer compound can be appliedbetween the clamp-on jacket and valve to improve its efficiency.

Combining these jacketed valves with extended bonnets forsafe convenient operation, and adding carbon graphite seatsor ceramic balls and seats enables the valve to handle abroad range of viscous materials.

13

Steam Jacketed Apollo®

Top Entry Ball Valves


Top Entry

#1 (PTFE)General application seat material, exhibiting lowest operatingtorque and excellent resistance to chemical attack. (Figure 1)Reference chart 1

#2 (RPTFE)Most commonly specified seat material, and used as the basis forpublished torque values. Maintains the excellent chemical resis-tance of unfilled Teflon® (PTFE) with increased resistance to wearand abrasion resulting in longer life. (Figure 1) Reference Chart 2

#3 (RPTFE w/Inner Ring)Features a metallic inner ring to improve abrasion resistance par-ticularly in high solids or throttling applications. Maintains the otherfeatures of the #2 seat. (Figure 2) Reference Chart 2

#7 (API 607 Cert. PTFE) to 500°FThis seat design has been successfully tested to the requirementsof API 607, fourth edition. The PTFE seat is fully confined by ametallic seat holder which provides a secondary seal in the eventof the loss of the primary PTFE seal due to a fire. As the seat sealmaterial is PTFE, chemical and torque characteristics will be thesame as in the #1 seats. (Figure 3) Reference Chart 1

#A (API 607 Cert. RPTFE) to 550°FThis seat design has been successfully tested to the requirementsof API 607, fourth edition. The RPTFE seat is fully confined by ametallic seat holder which provides a secondary seal in the eventof the loss of the primary PTFE seal due to a fire. The seat holdercan perform the same function as the inner ring found in the #3and #5 seats making this design appropriate for abrasive and throt-tling applications. As the seat seal material is RPTFE, chemicaland torque characteristics will be the same as in the #2 and #3seats. (Figure 3) Reference Chart 2

#5 (55%Bronze/5%Moly BRTFE)Specifically intended for steam applications. Also applicable toabrasive and throttling applications because of the heavy loadingof reinforcing materials and the presence of the inner ring.However, chemical compatibility may be a limiting factor in theapplication of this seat. (Figure 2) Reference Chart 3

“D” (60% Stainless Steel SRTFE)Intended for abrasive and throttling applications because of theheavy loading of reinforcing materials and the completely confinedseat. (Figure 2) Reference Chart 2

#6 (UHMWPE)Ultra High Molecular Weight Polyethylene offers good abrasionresistance making it suitable for use in high solids or slurry applica-tions. These seats are completely confined by a metallic seatholderenhancing their performance in abrasive services. This seat is fre-quently specified in services where fluorine off-gasing in even theslightest amounts is objectionable. Examples of these services arefood, tobacco processing, and nuclear services. (Figure 2) Reference Chart 4

“U” (UHMWPE)Exhibits the same characteristics as the #6 seat with the excep-tion that it utilizes the inner seat ring to enhance performance inabrasive services. UHMWPE should be used with caution in thepresence of solvents, and the operating torque can be expectedto be 30% higher than that of the teflon based seat materials.(Figure 1) Reference Chart 4

#8 (PEEK)PEEK (PolyEtherEtherKetone) offers a high strength alternativeto RPTFE, resistant to creep and cold flow. This seat offersgood abrasion resistance. Higher in cost, this material offerssimilar chemical resistance to PTFE but should be checked onapplication. Operating torque tend to be 40% higher thanRPTFE. Ball stop recommended. (Figure 2) Reference Chart 5

#B (Carbon Reinforced, PEEK)Carbon Reinforced PEEK provides improved abrasion resis-tance when compared to the unfilled variety. Higher in cost, thismaterial offers a broader temperature range than RPTFE withsimilar chemical resistance but should be checked on applica-tion. Operating torque tends to be 40% higher than RPTFE. Ballstop recommended. (Figure 2) Reference Chart 5

#4 (Carbon Graphite)Designed for high temperature applications. A ball stop isrequired in applications above 500°F. Maximum service temper-ature is limited to 750°F in oxidizing applications. This seat likeall rigid seat materials does not necessarily provide “bubbletight” shut-off. Most test standards have allowable leakage ratesor list “classes” of shut-off for this type of seat. Be aware of thesystem design requirements when specifing this or any rigidseat. Ball stop recommended. (Figure 1) Reference Chart 6

#H (High Temperature Graphite)Designed for very high temperature applications. A ball stop isrequired in applications above 500°F. Maximum service temper-ature is limited to 1000°F. This seat like other rigid seat materi-als does not provide “bubble tight” shut-off. This seat is not asabrasion resistant as the #4 version. Be aware of the systemdesign requirements when specifing this or any rigid seat. Ballstop recommended. (Figure 1) Reference Chart 6

#9 (Ceramic)Working in conjunction with a ceramic ball, this seat outperformsall other materials in throttling and abrasive applications. It pos-sesses excellent chemical resistance. Cost is very high, andunless experience dictates its use, other alternatives should beevaluated first. A ball stop is recommended for all applications.This seat like all rigid seat materials does not necessarily pro-vide “bubble tight” shut-off. Most test standards have allowableleakage rates or list “classes” of shut-off for this type of seat. Beaware of the system design requirements when specifing this or any rigid seat. (Figure 4) Reference Chart 7

14

Seat Performance Data

® Teflon is a registered trademark of DuPont


Ball Valves

Figure 1

Insert

Seat Ring

Figure 2

Insert

Seat Rings

Figure 3

Insert

Seatholder

15

Figure 4

Seal


Top Entry

16

Reference Chart 1

Reference Chart 2

All PTFE SeatsP-T Ratings

RPTFE SeatsP-T Ratings

Temperature (F)

Temperature (F)

Pre

ssu

re (

psi

g)

Pre

ssu

re (

psi

g)

150 CS150 SS300 CS300 SSPTFEF/S PTFE

150 CS150 SS300 CS300 SS600 CS600 SSRPTFEF/S RPTFE

17

Ball Valves


Reference Chart 3 Reference Chart 4

Reference Chart 5

#5 SeatP-T Ratings

UHMWPE SeatsP-T Ratings

All Peek SeatsP-T Ratings

Temperature (F)

Temperature (F)

Temperature (F)

Pre

ssu

re (

psi

g)

Pre

ssu

re (

psi

g)

Pre

ssu

re (

psi

g)

150 CS150 SS 300 CS300 SS600 CS600 SS#5 Seat

150 CS150 SS 300 CS300 SS600 CS600 SSUHMWPE

150 CS150 SS 300 CS300 SS600 CS600 SSPEEKC-PEEK

18

Top Entry


All Carbon-Graphite SeatsP-T Ratings

Ceramic SeatsP-T Ratings

Steam Rated SeatsP-T Ratings

Temperature (F)Temperature (F)

Pre

ssu

re (

psi

g)

Pre

ssu

re (

psi

g)

Reference Chart 7Reference Chart 6

150 CS150 SS 300 CS300 SS600 CS600 SS#4 Seat“H” Seat

150 CS150 SS 300 CS300 SS600 CS600 SSCeramic

Temperature (F)

Pre

ssu

re (

psi

g)

Reference Chart 8

150 CS150 SS 300 CS300 SS600 CS600 SS#4 Seat“H” SeatSteam#5 Seat


Ball Valves

Valve 150 300 300 300 300 600 600 600 600Size Class Class Class Class Class Class Class Class Class

Flanged Flanged Buttweld Socket NPT Flanged Buttweld Socket NPTEnd End End Weld End End Weld

1/2" 20 20 20 203/4" 50 50 50 30 30 50 50 30 301" 60 60 60 40 40 60 60 40 40 1-1/2" 100 100 100 70 70 100 100 70 702" 180 180 180 120 120 190 190 120 1203" 330 400 400 260 260 410 410 260 2604" 600 720 720 780 7806" 1,500 1,500 1,500 1,700 1,7008" 2,500 2,500 3,10010" 3,800 3,800 4,900

Valve 150 300 600Size Class Class Class

Flanged Flanged Flanged1" 95 90 85

1-1/2" 230 225 2002" 435 420 4003" 1050 1000 9504" 1950 1900 18006" 4800 4300 43008" 9100 8700 8000

The table above presents the FlowCoefficients (Cv) for Apollo® Top EntryBall Valves. This number represents theflow (in gallons per minute of water)required to produce a 1 psig pressuredrop across the valve. The data shown isfor a valve in the full open position. Datafor various degrees of open are availableupon request. The values shown repre-

sent the average for several tests which highlighted the variability of Flow Coefficients. It is not unreasonableto expect a 10% to 20% deviation for a specific valve from the nominal figures shown.Knowing specific system characteris-

tics; such as line size, flow rate, tempera-ture and pressure and knowing specific

fluid characteristics; such as specificgravity, density, or compressibility factorallows the verification of the pressuredrop across a known valve. Or converse-ly, in the absence of a valve size andknowing an acceptable pressure dropunder the described flow conditions it ispossible to select an appropriately sized valve.

Where: Q = Flow in SCFMPD = Pressure Drop (PSI)P2 = Outlet Pressure PSIAT = Temp.(°R) or (°F + 460)SG = Specific Gravity at flow

conditionsCV = Valve Flow Coefficient

Where: Q = Flow in US GPMPD = Pressure Drop (PSI)SG = Specific Gravity at flow

conditionsCV = Valve Flow Coefficient

Flow of Liquids Flow of Gases

or

19

Apollo® Top Entry Full Port Valve Flow Coefficients

Apollo® Top Entry Valve Flow Coefficients

SECTION J CONTENTSOPTIONAL CONFIGURATIONS

DESCRIPTION PAGE

Options Identification & Description J-1








J-1

Options-02: Static Grounding Device

-03, -04: 1-1/4” (-03) and 2-1/4” (-04) Zinc PlatedCarbon Steel Stem Extension Assemblies

-05: Plain Ball

-06: Special 2000 psig Trim

-07: Steel Tee Handle

Used to help prevent static electrical discharge (sparking) between valvecomponents. Accomplished by use of a stainless steel spring washer or coilspring (dependent on valve size). -02 grounds stem, lever & lever nut to valvebody.

Used to elevate the handle to accommodate pipe insulation or torelocate the position of the handle where necessary. Also availablewith balancing stop. (Example: 70-120-04)

Unplated ball available for bronze valves. Furnished exclusively bycustomer preference. Not recommended by engineering.

Available only for the 1-1/4" to 2" 73-100 Series. Consists of 316 SSball and stem (standard) with special configuration seats to increaseworking pressure. Three valves only: 73-106-06, 73-107-06 and 73-108-06.

Used where space limitation prevents use of the standardlever type handle. Useful also to help prevent accidentalopenings by: Limiting projection of the operating devicedistance beyond the valve and increasing the turning forcerequired to operate valve. Also, balances the turning effectof vibration.

Length ofExtension

CII 22000 WOG


J-2

Options

-08: 90º Reversed Stem

-10: SS Lever And Nut

-13: Stamped 157 SWP

-14: Side Vented Ball

Lever grip no longer indicates flow or no flow.(Valve shown in open position).

Stamped 157 SWP

(Uni-Directional Flow)Vent is on the upstream side.Valve body will be stamped with arrow indicating properflow direction.Equalizes pressure gain caused byliquid thermal expansion, preventing seat blow-out .Does not reduce the load capability of seats.

600 WOG 157SWP


Direction of Flow

J-3

Options-15: Steel Wheel Handle

Prevents accidental operation and balancesthe turning effect of vibration.

-16: -58: Horizontal Or Vertical Chain Lever

Horizontal Or Vertical Chain Lever

-17: Rough Chrome PlatedRough Chrome Plated

-20: Slot Vented Ball

(Bi-Directional Flow)Available on bronze balls. (All otherball materials are already slot-vented).

600 WOG


J-4

Options-24: Graphite Stem Packing- Necessary for firesafe design

-27: SS Latch-Lock Handle and SS Nut

-28: Mounting Pads Not Threaded

-29: 1500 psig 3-Piece Firesafe DesignGraphite packing and gaskets

-32: SS Tee Handle And Nut

-35: PTFE TrimReduces operating torque approx. 30%


J-5

Options-39: SS High-Rise Locking Wheel Handle

-45: Less Lever And Nut

-60: Grounded Ball And Stem


Grounded Ball And Stem

-50: 2-1/4” Locking Stem ExtensionZinc Plated CS

-47: SS Latch-Lock Oval HandleSS Latch-Lock Oval Handle

-46: SS Lock Closed OnlyLatch-Lock Handle

-40: Cyl-Loc

1/00

J-6

Options

-19U.S. PATENT

#4,498,320PAD-LOCKING DEVICESFOR 72 & 73 SERIES

-19

PAD-LOCKING DEVICESFOR 76 & 89 SERIES

-19

PAD-LOCKING DEVICES86-100-19 SERIES

RECOMMENDED FOR AFTERMARKET

FPOSTRIPIN “A"HERE

FPOSTRIPIN “B"HERE

FPOSTRIPIN “C"HERE


J-7

Options

TANK BOTTOMFLANGE VALVE

2" SIZE ONLY

-23

CAM-LOCKOPTIONAL

HANDLE

-30

SS BODY TRIM(BOLTS, NUTS &

LEVER)

-59

FPO,STRIP IN“E" HERE


J-8

Options

Automatic Drain (-41)

• Conforms to certain OSHA requirements in pneumatic installations

• Easy, safe maintenance of pneumatic tools• Cannot be used where drained media could

cause damage• Temperature range =+50°F to 200°F• Recommended for water or air sevices only• Pressures 0- 125 psig


TYPICAL AUTO-DRAIN OPERATION

WHEN THIS VALVE IS SHUT OFF FOR MAINTENANCEOF A PNEUMATIC TOOL, PRESSURE BETWEEN THEVALVE AND TOOL IS AUTOMATICALLY DRAINED TOATMOSPHERE TO PREVENT POSSIBLE INJURY CAUSED BY ACCIDENTIAL OPERATION OF THE TOOL.

NOTE: Temperature variations and dirty systems can cause vent discharge in both the open and closed positions.

70-100 (Threaded)

PRESSURE

PRESSURE

VALVE IN OPEN POSITIONDRAIN VENT SHUT OFF.

VALVE CLOSED AND DRAINING.UPSTREAM SEAT STOPS AIR FLOW.DOWNSTREAM SYSTEM IS VENTEDTO ATMOSPHERE.

75-104-41

TO PNUEMATIC PRESS OROTHER PNUEMATIC TOOL

MAIN AIR LINE

SECTION N CONTENTSENGINEERING DATA

DESCRIPTION PAGE

Flow Data70-100, 71-100, 73-100, 74-100, 76-100, 80-100, 81-100 & 89-100 Series N-1

77-100, 82-100, 83-100, 86-100, 83-500 & 86-600 Series N-2

87-100, 88-100, 87-700, 88-700, 87-200 & 88-200 Series N-3

9A-100, 90-100, 91-100, 92-100, 93-100, 96-100, 83-300 & 85-100 Series N-4

70-600, 76-600 & 72 Series N-5

Cautionary Statement N-6

Torque Constants For Apollo End Entry Valves N-7

Apollo Ball Valve Seat Application Guide N-8

Pressure Temperature CurvesClass 150 Carbon and Stainless Steel Ball Valves N-9

400# and 600# Bronze Ball Valves N-10

Class 300 Carbon and Stainless Steel Ball Valves N-11

1000# Carbon and Stainless Steel Ball Valves N-12

Class 600 Carbon and Stainless Steel Ball Valves N-13



3000# Carbon Steel Ball Valves N-16

Refrigeration Valves N-16

400# Carbon Steel Ball Valves N-17

Class 150 Alloy 20 Ball Valves N-17

1500# Alloy 20 Ball Valves N-18

2000# Alloy 20 Ball Valves N-18

800# Stainless Steel Ball Valves N-19

800# Nickel Ball Valves N-19

Apollo Ball Valve Material Reference Data N-20 & N-21

Philips Real Time Radiographic System N-22

Conversion Factors N-23 & N-24

N-1COPYRIGHT ©1997 CONBRACO IND., INC. – PRINTED IN U.S.A.

FLOW DATAFor Apollo® and Saturn® Ball Valves

The listed Cv “factors” are derived from actual flow testing, in the Apollo® Ball Valve Division, ConbracoIndustries, Inc., Pageland, South Carolina. These tests were completed using standard “off the shelf” valves withno special preparation and utilizing standard schedule 40 pipe. It should be understood that these factors are forthe valve only and also include the connection configuration. The flow testing is done utilizing water as a fluidmedia and is a direct statement of the gallons of water flowed per minute with a 1 psig pressure differentialacross the valve/connection unit. Line pressure is not a factor. Because the Cv is a factor, the formula can be usedto estimate flow of most media for valve sizing.

SIZE 1/4" 3/8" 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" 2-1/2" 3"OPEN 90° 8.4 7.2 15 30 43 48 84 108 503 370

80° 5.3 4.6 9.3 17 28 33 54 75 310 22570° 2.5 2.4 5.0 9.0 16 19 31 44 167 13760° 1.2 1.2 2.9 5.1 9.2 12 20 28 86 8450° 0.6 0.6 1.8 2.9 5.8 7.6 12 17 55 5440° 0.2 0.2 1.0 1.5 3.1 4.2 6.3 9.6 32 3130° 0.1 0.1 0.4 0.7 1.6 2.1 3.2 4.8 18 1620° 0 0 0.1 0.1 0.4 0.7 0.8 1.3 7.4 6.110° 0 0 0 0 0 0 0 0 0.5 0.1

CLOSED 0° 0 0 0 0 0 0 0 0 0 0

Cv FACTORSSERIES:

70-100, 71-100, 73-100, 73A-100,74-100, 76-100, 80-100

81-100, 89-100

DEG

REE

RO

TATI

ON

Flow of Liquid

Q = Cv ∆PSpGr

or ∆P = (Q)2 (SpGr)(Cv)2

Flow of Gas

Q = 1360 Cv (∆P) (P2)(SpGr) (T)

or ∆P = 5.4 x 10-7 (SpGr) (T) (Q)2

(Cv)2 (P2)

Where:Q = flow in SCFH

∆P = pressure drop (psig)SpGr = specific gravity

(based on air = 1.0)P2 = outlet pressure–psia

(psig + 14.7)T = (temp. °F + 460)

Cv = valve constant

Where:Q = flow in US gpm

∆P = pressure drop (psig)SpGr = specific gravity at

flowing temperatureCv = valve constant

1/00

N-2 COPYRIGHT ©1997 CONBRACO IND., INC. – PRINTED IN U.S.A.

SIZE 1/4" 3/8" 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" 2-1/2"OPEN 90° 8.1 15 15 51 68 125 177 389 503

80° 6.9 11 11 31 44 74 108 195 31070° 4.2 6.1 5.4 15 24 33 52 92 16760° 2.5 3.4 3.2 8.3 13 20 30 54 8650° 1.4 2.0 1.9 4.4 7.5 12 17 31 5540° 0.8 1.0 1.0 2.5 4.0 6.3 9.3 16 3230° 0.4 0.4 0.4 1.1 2.1 2.9 4.7 7.8 1820° 0.1 0.1 0.1 0.2 0.5 0.8 1.3 2.1 7.710° 0 0 0 0 0 0 0 0 0.7

CLOSED 0° 0 0 0 0 0 0 0 0 0

Cv FACTORS77-100 SERIES

SIZE 1/4" 3/8" 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" 2-1/2" 3" 4"OPEN 90° 8.1 14 26 51 68 120 170 376 510 996 1893

80° 6.9 10 19 33 46 70 99 190 308 486 89870° 4.2 5.8 8.8 15 24 33 47 90 165 211 38860° 2.6 3.4 4.4 8.2 13 20 29 53 82 119 21850° 1.6 1.8 2.3 4.3 7.5 12 17 30 53 69 12240° 1.0 1.0 1.2 2.3 4.0 6.3 9.2 16 31 36 7130° 0.4 0.5 0.5 1.0 2.1 3.2 4.6 7.6 17 19 3820° 0.1 0.1 0.1 0.3 0.5 0.7 1.3 2.0 6.6 7.4 1410° 0 0 0 0 0 0 0 0 0.7 0.7 1.0

CLOSED 0° 0 0 0 0 0 0 0 0 0 0 0

Cv FACTORS82-100, 82-200, 83-100, 86-100, 86-700, 83-500 & 86-600 SERIES

DEG

REE

RO

TATI

ON

DEG

REE

RO

TATI

ON


SIZE 1" 1-1/2" 2" 2-1/2" 3" 4" 6" 8"(1) 10" (1)(2) 12" (1)

(2)

OPEN 90° 75 195 410 545 1021 2016 4837 5896 9213 13,26780° 47 123 199 311 488 917 2205 2529 3952 569170° 23 53 90 165 211 390 908 1412 2206 317760° 13 30 53 84 119 220 509 875 1367 196950° 7.6 18 31 52 69 122 298 554 866 124740° 4.1 10 16 29 36 71 170 337 527 75830° 2.1 5.1 7.9 16 19 39 92 192 300 43220° 0.7 1.7 2.1 6.4 7.4 14 35 81 127 18210° 0 0 0 0.5 0.6 1.0 4.7 13 20 29

CLOSED 0° 0 0 0 0 0 0 0 0 0 0

Cv FACTORS87-200 & 88-200 SERIES

87A-200 & 88A-200 SERIES

DEG

REE

RO

TATI

ON

SIZE 1/2" 3/4" 1" 1-1/2" 2" 2-1/2" 3" 4" 6" 8" 10"(1)(2)

OPEN 90° 15 19 47 86 104 234 375 673 1099 1902 297280° 11 14 32 57 71 157 231 418 663 1204 188170° 5.7 7.6 17 32 45 78 133 232 414 761 118960° 3.3 4.3 9.9 20 29 53 83 143 277 483 75550° 1.9 2.4 5.7 12 18 32 52 84 174 310 48440° 1.1 1.4 3.2 6.7 10 18 31 53 106 188 29430° 0.5 0.6 1.7 3.2 5.3 9.5 16 29 56 104 16020° 0.1 0.1 0.5 0.9 1.8 3.3 6.0 11 23 39 6110° 0 0 0 0 0 0 0.3 0.9 3.0 4.6 7.1

CLOSED 0° 0 0 0 0 0 0 0 0 0 0 0

Cv FACTORS87-100 & 88-100 SERIES87-700 & 88-700 SERIES

87A-100 & 88A-100 SERIES

DEG

REE

RO

TATI

ON

(1) Data for standard ball. Data for solid ball on request.(2) 10" & 12" valve data was calculated and based on actual available data.

1/00


SIZE 1/2" 3/4" 1" 1-1/4" 1-1/2" 2"OPEN 90° 16 18 35 48 84 104

80° 9.9 13 23 32 53 7370° 4.8 7.6 13 19 30 4360° 2.8 4.6 7.3 12 20 2750° 1.7 2.7 4.5 7.2 12 1640° 0.9 1.5 2.5 3.8 6.3 9.430° 0.5 0.7 1.1 2.1 3.2 4.720° 0.1 0.2 0.3 0.7 0.8 1.310° 0 0 0 0 0 0

CLOSED 0° 0 0 0 0 0 0

Cv FACTORS83-300 & 85-100 SERIES

DEG

REE

RO

TATI

ON

SIZE 1/4" 3/8" 1/2" 3/4" 1" 1-1/4" 1-1/2" 2"OPEN 90° 8.3 6.7 5.7 10 16 25 40 62

80° 5.9 4.7 4.1 7.6 11 19 29 4670° 3.3 2.8 2.8 4.6 6.3 12 19 3060° 1.8 1.7 1.8 2.8 4.2 7.5 12 1950° 1.1 1.1 1.1 1.8 2.4 4.6 7.5 1240° 0.6 0.6 0.6 1.0 1.4 2.6 4.2 6.830° 0.3 0.3 0.3 0.5 0.6 1.3 2.3 3.220° 0.1 0.1 0.1 0.1 0.1 0.3 0.7 1.010° 0 0 0 0 0 0 0 0

CLOSED 0° 0 0 0 0 0 0 0 0

Cv FACTORS9A-100, 90-100, 91-100,

92-100, 93-100 & 96-100 SERIES

DEG

REE

RO

TATI

ON


SIZE 1/2" 3/4" 1" 1-1/4" 1-1/2" 2"OPEN 90° 26 48 65 125 170 216

80° 20 29 45 75 104 13670° 10 15 24 34 49 6860° 5.5 8.0 13 20 30 4150° 2.8 4.3 7.5 12 17 2440° 1.6 2.4 4.3 6.3 9.2 1430° 0.8 1.1 2.1 3.2 4.6 6.920° 0.2 0.3 0.7 0.8 1.3 2.110° 0 0 0 0 0 0

CLOSED 0° 0 0 0 0 0 0

Cv FACTORS“72” SERIES

DEG

REE

RO

TATI

ON

SIZE1/2" 3/4" 1" 1-1/4" 1-1/2" 2"5.4 12 14 21 34 47

Cv FACTORS70-600 & 76-600

SERIES

N-5


Engineering Data

CAUTION

FOLLOWING, ARE SOME SAFEGUARDS THAT MUST BE CONSIDERED PRIOR TO INSTALLATION.

EASE OF OPERATION - BALL VALVES ARE EASIER TO OPERATE THAN OTHER TYPES OF SHUT-OFFVALVES. WHEN THESE VALVES ARE INSTALLED SO THAT THERE IS A POSSIBILITY THAT THEHANDLES CAN BE HOOKED OR SNAGGED, APPROPRIATE ACTION TO PREVENT ACCIDENTAL ORUN-WANTED OPENING OR CLOSING OF THE VALVE MUST BE TAKEN. VIBRATIONS IN, THROUGHOR AROUND THE VALVE CAN ALSO CAUSE ACCIDENTAL OR UN-WANTED OPENING OR CLOSINGOF THE VALVE.

PRESSURE RELIEF - DETERMINE AND PROVIDE CORRECTIVE ACTION AGAINST EXCESSIVEPRESSURE BUILD UP IN THE VALVE OR PIPING SYSTEM DUE TO THERMAL EXPANSION. THERMALEXPANSION CAN CREATE EXTREME PRESSURES WELL ABOVE THE WORKING PRESSURE LIMIT OFTHE VALVE WHICH CAN CAUSE LEAKING OR BURSTING OF THE VALVE.

SUPPORTS - IF YOU CHOOSE TO CONNECT A FLEXIBLE HOSE OR OTHER NON-RIDGED CONDUITTO THE VALVE, THE DESIGN OF SUCH INSTALLATION MUST PREVENT ANY “WHIPPING ACTION”THAT COULD INJURE OR DAMAGE PERSONNEL OR EQUIPMENT. VALVE MUST BE IMMOBILE.

FITTINGS - USE ONLY THOSE FITTINGS OR PIPING THAT ARE COMPATIBLE WITH THE VALVESBEING USED TO PREVENT BREAKAGE AND/OR LEAKAGE. (AS FOR ONE EXAMPLE, IT IS POORPRACTICE AND NEVER RECOMMENDED TO USE PLASTIC PIPE OR FITTINGS WITH METALLICVALVES SINCE THERMAL EXPANSION, EXTERNAL FORCES OR OTHER SITUATIONS CAN CAUSEBREAKAGE OR LEAKAGE AT OR NEAR THE JOINT).

PRESSURE/TEMPERATURE LIMITS - THE MAXIMUM WORKING PRESSURE LIMIT OF THE VALVE ISMARKED ON THE VALVE BODY. NEVER EXCEED THIS “WOG” RATING WHICH IS SPECIFIED UP TO100°F. TEMPERATURES HIGHER THAN 100°F DECREASE THE MAXIMUM WORKING PRESSURELIMIT. REFER TO THE APPROPRIATE PRESSURE/TEMPERATURE CHART THAT IS PUBLISHED IN THECATALOG OR SPECIFICATION SHEET FOR THE PARTICULAR VALVE BEING INSTALLED.

FREEZING - PROVIDE MEANS TO PROTECT THE VALVE FROM FREEZING AND BURSTING WHENUSED WITH LIQUIDS.

FLUID COMPATIBILITY - CONSIDER THE CORROSIVE, EROSIVE AND ADHESIVE EFFECTS OFFLUIDS ON THE VALVE AND PIPING COMPONENTS. IT IS YOUR RESPONSIBILITY TO ENSURE THATTHE VALVE IS COMPATIBLE WITH THE MATERIAL(S) USED IN THE SYSTEM.

INSTALLATION - THE USE OF PTFE PIPE TAPE AS A SEALANT IS RECOMMENDED FOR THREADEDVALVES WHEN MAKING JOINTS. CORRECT LUBRICATION OF STAINLESS STEEL PIPE THREADS ISESPECIALLY IMPORTANT TO PREVENT THREAD GALLING. DO NOT APPLY EXCESSIVE TORQUEWHEN INSTALLING THE VALVE. TO PREVENT DISTORTION OR DAMAGE TO THE VALVE, DO NOTAPPLY TORQUE THROUGH THE VALVE. USE PROPER SUPPORTS IN HANDLING PRE-FABRICATEDSECTIONS AND IN FINAL INSTALLATION. ALWAYS TEST THE SYSTEM BEFORE USING.

MAINTENANCE - DO NOT DISASSEMBLE THE VALVE WHILE UNDER PRESSURE. REQUEST AMAINTENANCE MANUAL BEFORE ATTEMPTING REPAIRS TO THE VALVE.

MATERIALS CHEMICAL RESISTANCE CHARTS AVAILABLE ON REQUEST.

IT IS THE INSTALLER'S AND/OR SYSTEM DESIGNER'S RESPONSIBILITY TO ENSURE THAT THESE VALVESARE INSTALLED IN ACCORDANCE WITH APPLICABLE AND CURRENT ANSI B31 STANDARDS.

N-7COPYRIGHT ©1997 CONBRACO IND., INC. – PRINTED IN U.S.A.1/00

Note (1) Constants are used to determine the in-service torque requirements of Conbraco’s valves.Note (2) Constants are based on RPTFE seats and clean dry air at the stated differential pressure.* Torques tested with multifilled seats.** 71-ARX-64 and 77-ARX-64 rated to 600 psig maximum.

TORQUE CONSTANTS FOR APOLLO® TWO PIECE ACTUATOR-READY VALVESDIFFERENTIAL PRESSURE psig 100 200 400 600 800 1,000 1,500 2,000

Valve Model1/4 - 1/2 25 26 27 28 30 32 35 38

*STD PORT 3/4 50 50 52 54 57 60 64 72**71-ARX-64 1 85 86 88 90 94 97 110 138

89-ARX-64 1-1/4 140 140 145 156 160 172 19476-ARX-64 1-1/2 160 164 173 186 195 201 235

2 220 230 258 270 310 350 4602-1/2 450 495 576 680 790 900

3 500 540 700 820 920 10301/4 - 1/2 25 26 27 28

*FULL PORT 3/4 50 54 60 70**77-ARX-64 1 140 148 160 180

1-1/2 290 300 310 3402 340 655 420 563

TORQUE CONSTANTS FOR APOLLO® END ENTRY VALVES (1),(2)DIFFERENTIAL PRESSURE psig 200 400 600 800 1,000 1,500

Valve Model SizeSTD PORT 1/4 & 1/2 35 35 40 43 46 4870-64X 3/4 50 50 54 59 62 6471-14X 1 101 101 103 106 116 13076-10X 1-1/4 171 171 205 216 246 28676-60X 1-1/2 192 192 216 265 280 31189-14X 2 271 271 276 300 309 354399-10X 2-1/3 & 3 715 715 790 1,200

1/4 & 1/2 35 35 403/4 74 74 84

FULL PORT 1 234 234 250BRONZE 1-1/4 286 286 32177-14X 1-1/2 357 357 398

2 650 650 7222-1/2 & 3 715 715 790

1/2 35 35 40 43 46 48STD PORT 3/4 78 78 90 123 140 1573-PIECE 1 156 156 178 201 229 25783-34X & 44X 1-1/4 208 208 230 248 282 31785-10X & 20x 1-1/2 234 234 276 309 352 395

2 350 350 390 450 513 576FULLPORT 1/4 & 1/2 78 78 90 123 140 1573-PIECE 3/4 156 156 178 201 229 25782-14X & 24X 1 208 208 230 248 282 31783-14X, 24X & 74X 1-1/4 234 234 276 309 352 39583-54X & 64X 1-1/2 350 350 390 450 513 57686-10X, 20X & 70X 2 715 715 755 800 912 1,02486-50X & 60X 3 1,030 1,030 1,087 1,148 1,212401-10X 4 1,830

1/2 35STD PORT 3/4 48FLANGED 1 9687A, 87-10X & 70X 1-1/2 18688A, 88-14X & 74X 2 268 340 386 65187A-40X 2-1/2 45788-808 3 718 911 1,038

4 1,200 1,524 1,7376 2,315 2,940 3,3518 4,118 6,00010 8,193

1/2 80 1203/4 100 170

1 140 2001-1/2 257 400

FULL PORT 2 457 700FLANGED 2-1/2 71387A, 87-20X, 900 3 1,038 180088A, 88-20X, 900 4 1,830 3700

6 4,117 104008 7,817 2600010 13,44012 16,470

TORQUE CONSTANTS FOR TOP ENTRY VALVES (1)Differential Pressure (psig)

Seat Options Valve Size 100 285 500 740 1,480***1 7*** 1/2 thru 1 85 110 140 180 290

1-1/2 205 260 330 415 6602 A2 350 430 550 735 1,200

3 3 950 1,250 1,650 2,000 3,200C4 2,000 2,500 3,300 4,100 6,5006 5,300 6,700 8,200 11,400 18,0005 D8 11,000 14,000 18,500 25,000 36,000

*6 Z** 10 18,500 22,000 30,000 40,000 62,0001/2 thru 1 115 160 210 260 450

4 1-1/2 270 370 480 590 1,0008 2 475 650 860 1,050 1,750

**** 9 3 1,250 1,850 2,400 2,950 4,9004 2,700 3,700 4,900 5,900 10,000

B 6 7,410 10,100 13,400 16,400 25,3008 15,000 20,000 26,000 32,000 56,00010 25,000 32,000 45,000 60,000 96,000

** Rated torque for#6 and U sectionadd 30%

*** Rated torque for#1 & #7 PTFEseats can bereduced by 30%.

**** Rated torque for#9 ceramic seatis to be increasedby 10%.


Conbraco Industries

Apollo® Ball ValveSeat Application Guide

Designation Range General Description

-01 (RPTFE) to 450°F Glass Reinforced PolyTetraFluoroEthylene Seat Seals and Packings: Most commonly specified seat material. Maintains the chemical resistance of PTFE with increased resistance to wear and abrasion resulting in longer life.

-21 (UHMWPE) to 180°F Ultra High Molecular Weight Polyethylene Seats with Graphite Seals and Packings: Offers good abrasion resistance making it suitable for use in high solids or slurry applications. This seat is frequently specified in services where fluorine off-gassing in even the slightest amounts is objectionable, services such as food and tobacco processing, and Nuclear services. UHMWPE should be used with caution in the presence of solvents, and the operating torque can be expected to be 30% higher than RPTFE seat materials.

-35 (PTFE) to 400°F PolyTetraFluoroEthylene (PTFE) Seats, Seals and Packings: General application seat material, exhibiting lowest operating torque and excellent resistance to chemical attack.

-38 (PEEK) to 550°F PolyEtherEtherKetone Seats with Graphite Seals and Packings: Offers a high strength alternative to RPTFE, resistant to creep and cold flow. This seat offers good abrasion resistance. This material offers similar chemical resistance to PTFE but should be checked on application. Operating torque tends to be 40% higher than RPTFE.

-56 (Multifill) to 500°F Carbon and Graphite Reinforced PTFE Seats, Seals and Packings: Reduced creep and cold flow like any RPTFE but with 20% lower operating torque than the glass reinforced versions.

-64 (Multifill) to 500°F Carbon and Graphite Reinforced PTFE Seats, Seals and Packings: Reduced creep and cold flow like any RPTFE but with 20% lower operating torque than the glass reinforced versions. Includes handle graphics for 250 psig saturated steam.

-65 (Multifill) to 500°F Carbon and Graphite RPTFE Seats, Graphite Seals and Packings:Reduced creep and cold flow like any RPTFE but with 20% lower operating torque than the glass reinforced versions.This configuration is also good for steam applications.


Class 150 CS P-T Rating(Graph 1)

Class 150 SS P-T Rating(Graph 2)


400# Bronze P-T Rating(Graph 3)

600# Bronze P-T Rating(Graph 4)





1000# CS P-T Rating(Graph 7)

1000# SS P-T Rating(Graph 8)












Refrigeration Valve P-T Rating(Graph 16)



Class 150 Alloy 20 P-T Rating(Graph 18)


1500# Alloy 20 P-T Rating(Graph 19)

2000# Alloy 20 P-T Rating(Graph 20)



800# Nickel P-T Rating(Graph 22)


APOLLO® BALL VALVEMATERIAL REFERENCE DATA

Item/Property Barstock Casting Forging

Carbon SteelASTM Specifications A108-1215 A216-WCB A105Unified Numbering System G12150 J03002 K03504MAJOR ELEMENTSCarbon 0.09% max. 0.30% max. 0.35% max.Manganese 0.75 - 1.05% 1.00% max. 0.60 - 1.05%Phosphorus 0.04 - 0.09% 0.04% max. 0.04% max.Sulfur 0.26 - 0.35% 0.045% max 0.05% max.Silicon - 0.60% max. 0.35% max.MECHANICAL PROPERTIESTensile Strength 70,000 psi min. 70,000 psi min. 70,000 psi min.Yield Strength 36,000 psi min. 36,000 psi min. 36,000 psi min.

316 Stainless SteelASTM Specifications A276-316 A351-CF8M A182-F316Unified Numbering System S31600 J92900 S31600MAJOR ELEMENTSCarbon 0.08% max. 0.08% max. 0.08% max.Chromium 16.00 - 18.00% 18.00 - 21.00% 16.00 - 18.00%Molybdenum 2.00 - 3.00% 2.00 - 3.00% 2.00 - 3.00%Nickel 10.00 - 14.00% 9.00 - 12.00% 10.00 - 14.00%MECHANICAL PROPERTIESTensile Strength 75,000 psi min. 70,000 psi min. 75,000 psi min.Yield Strength 30,000 psi min. 30,000 psi min. 30,000 psi min.

316L Stainless SteelASTM Specifications A276-316L A351-CF3M A182-F316LUnified Numbering System S31603 J92800 S31603MAJOR ELEMENTSCarbon 0.03% max. 0.03% max. 0.03% max.Chromium 16.00 - 18.00% 17.00 - 21.00% 16.00 - 18.00%Molybdenum 2.00 - 3.00% 2.00 - 3.00% 2.00 - 3.00%Nickel 10.00 - 14.00% 9.00 - 13.00% 10.00 - 15.00%MECHANICAL PROPERTIESTensile Strength 70,000 psi min. 70,000 psi min. 75,000 psi min.Yield Strength 25,000 psi min. 30,000 psi min. 30,000 psi min.

Alloy 20ASTM Specifications B473-N08020 A351-CN7M B462-N08020Unified Numbering System N08020 N08007 N08020MAJOR ELEMENTSChromium 19.00 - 21.00% 19.00 - 22.00% 19.00 - 21.00%Copper 3.00 - 4.00% 3.00 - 4.00% 3.00 - 4.00%Manganese 2.00% max. 1.50% max. 2.00% max.Molybdenum 2.00 - 3.00% 2.33 - 3.00% 2.00 - 3.00%Nickel 32.00 - 38.00% 27.50 - 30.50% 32.00 - 38.00%MECHANICAL PROPERTIESTensile Strength 80,000 psi min. 62,000 psi min. 80,000 psi min.Yield Strength 35,000 psi min. 25,000 psi min. 35,000 psi min.


APOLLO® BALL VALVEMATERIAL REFERENCE DATA

Item/Property Barstock Casting Forging

NickelASTM Specifications B160-N02200 A494-CZ100 B160-N02200Unified Numbering System N02200 N02100 N02200MAJOR ELEMENTSMolybdenum 2.00 - 3.00% 2.33 - 3.00% 2.00 - 3.00%Nickel 99.00% max. 95.00% min. 99.00% max.MECHANICAL PROPERTIESTensile Strength 55,000 psi min. 50,000 psi min. 55,000 psi min.Yield Strength 15,000 psi min. 18,000 psi min. 15,000 psi min.

Nickel-Copper AlloyASTM Specifications B164-N04400 A494-M35-1 B564-N04400Unified Numbering System N04400 N/A N04400MAJOR ELEMENTSCopper 28.00 - 34.00% 26.00 - 33.00% 28.00 - 34.00%Iron 2.50% max. 3.50% max. 2.50% max.Manganese 2.00% max. 1.50% max. 2.00% max.Molybdenum 2.00 - 3.00% 2.33 - 3.00% 2.00 - 3.00%Nickel 63.00% min. 60.00% min. 63.00% min.MECHANICAL PROPERTIESTensile Strength 70,000 psi min. 65,000 psi min. 70,000 psi min.Yield Strength 25,000 psi min. 25,000 psi min. 25,000 psi min.

Leaded Brass & Bronze AlloysASTM Specification B16 B584-C84400Unified Numbering System C36000 C84400MAJOR ELEMENTSCopper 60.0 - 63.0% 78.0 - 82.0%Tin 2.3 - 3.5%Lead 2.5 - 3.7% 6.0 - 8.0%Zinc 33.0 - 37.5% 7.0 - 10.0%MECHANICAL PROPERTIESTensile Strength 25,000 psi min. 29,000 psi min.Yield Strength 10,000 psi min. 13,000 psi min.

85-5-5-5 Bronze AlloysASTM Specification N/A B62-C83600Unified Numbering System C83600 C83600MAJOR ELEMENTSCopper 84.0 - 86.0% 84.0 - 86.0%Tin 4.0 - 6.0% 4.0 - 6.0%Lead 4.0 - 6.0% 4.0 - 6.0%Zinc 4.0 - 6.0% 4.0 - 6.0%MECHANICAL PROPERTIESTensile Strength 30,000 psi min. 30,000 psi min.Yield Strength 14,000 psi min. 14,000 psi min.


Conbraco Industries

Philips Real Time Radiographic SystemOur in house, state-of-the-art radiograph system allows for the highest quality and most expedientcasting inspection and approval system in the industry.

This system consists of:

• Philips MG450, 450 KV Constant Potential X-Ray Generation Unit with MCH 451 Tube Head

• Imaging system utilizing a High Grade Image Intensification Unit coupled to a High ResolutionCamera and Monitor

• Digital Image Processor

• A 300# Capacity, Precision 5 Axis Motorized Parts Manipulator, Manually Controlled orProgrammable

• Ergonomically Designed Operator Control Console with Video Tape and Thermographic RecordingCapabilities

• Programmable Systems Controller

• Philips Trained Operations Technicians

This system allows you, the Customer, the ability to visually inspect the valves that are beingmanufactured in our Investment Casting facility, as they are in the manufacturing process.

This service allows for the fastest delivery of project work and constant reassurance that the valves thatare being supplied will meet or exceed your stringent specifications.

Inspection can be done with actual X-RAY film, or with a REAL TIME X-RAY Video Tape of the Valves,which can be viewed on a VHS player at your facility.

COPYRIGHT ©1997 CONBRACO IND., INC. – PRINTED IN U.S.A. N-23

atmospheres cms of mercury 76.0atmospheres ft. of water (at 4°C) 33.90atmospheres in. of mercury (at 0°C) 29.92atmospheres kgs/sq cm 1.0333atmospheres kgs/sq meter 10,332atmospheres pounds/sq. in. 14.70Bar newtons/sq m 105

bar atmospheres 0.9869bar at (tech.) 1.0197bar psi 14.504

Barrels-Oil gals-oil 42BT Units kg-calories 0.2520BTU’s ft-lbs 777.9BTU’s hp-hrs 3.927 x 10-4

BTU’s kgs-meters 107.5BTU’s kw-hrs 2.928 x 10-4

BTU/Min ft-lbs/sec 12.96BTU/min hp 0.02356BTU/min kw 0.01757BTU/min watts 17.57

Centimeters inches 0.3937cm meters 0.01cm mm 10

Cms Mercury atm 0.01316cms mercury ft water 0.4461cms mercury kgs/sq meter 136.0cms mercury lbs/sq ft 27.85cms mercury lbs/sq in 0.1934

Cms/Second ft/min 1.969cms/sec ft/sec 0.03281cms/sec km/hr 0.036cms/sec meters/min 0.6cms/sec miles/hr 0.02237cms/sec miles/min 3.728 x 10-4

Cms/Sec/Sec ft/sec/sec 0.03281Cubic Cms cu ft 3.531 x 10-5

Cu cms cu in 6.102 x 10-2

cu cms cu meters 10-6

cu cms cu yds 1.308 x 10-6

cu cms gals 2.642 x 10-4

cu cms liters 10-3

cu cms pints (liq) 2.113 x 10-3

cu cms quarts (liq) 1.057 x 10-3

Cubic Feet cubic cms 2.832 x 104

cu ft cu inches 1728cu ft cu meters 0.02832cu ft cu yds 0.03704cu ft gals 7.48052cu ft liters 28.32cu ft pints (liq) 59.84cu ft quarts (liq) 29.92

Cu Ft/min cu cms/sec 472.0cu ft/min gals/sec 0.1247cu ft/min liters/sec 0.4720cu ft/min lbs water/min 62.43cu ft/sec gals/min 448.831

Cu Inches cc 16.39cu ins cu ft 5.787 x 10-4

cu ins cu meters 1.639 x 10-5

cu ins cu yds 2.143 x 10-5

cu ins gals 4.329 x 10-3

cu ins liters 1.639 x 10-2

cu ins pints (liq) 0.03463 cu ins quarts (liq) 0.01732

Cu Meters cc 104

cu M cu ft 35.31cu M cu ins 61,023cu M cu yds 1.308cu M gals 264.2cu M liters 103

cu M pints (liq) 2113cu M quarts (liq) 1057

Cu Yards cu cms 7.646 x 105

cu yds cu ft 27cu yds cu ins 46,656cu yds cu meters 0.7646cu yds gals 202.0

Decimeters meters 0.1Deg (Angle) minutes 60degs (angle) radians 0.01745degs (angle) secs 3600

Degrees/Sec radians/sec 0.01745degs/sec revs/min 0.1667degs/sec revs/sec 0.002778

Feet cms 30.48ft ins 12ft meters 0.3048ft yds 1/3

Ft of Water atms 0.02950ft of w ins mercury 0.8826ft of w kgs/sq cm 0.03048ft of w lbs/sq ft 62.32ft of w lbs/sq in 0.4328

Feet/Min cms/sec 0.5080ft/min ft/sec 0.01667ft/min kms/hr 0.01829ft/min meters/min 0.3048ft/min miles/hr 0.01136

Ft/Sec/Sec cms/sec/sec 30.48ft/sec/sec Meters/sec/sec 0.3048

Ft-Pounds BTU s 1.286 x 10-3

ft lbs hp-hrs 5.050 x 10-7

ft lbs kg-calories 3.241 x 10-4

ft lbs kg-meters 0.1383ft lbs kw-hrs 3.766 x 10-7

Ft-lbs/Min BTUs/min 1.286 x 10-3

ft-lbs/min ft-lbs/sec 0.01667ft-lbs/min hp 3.030 x 10-5

ft-lbs/min kg-calories/min 3.241 x 10-4

ft-lbs/min kws 2.260 x 10-5

Ft-Lbs/Sec BTUs/min 7.717 x 10-2

ft-lbs/sec hp 1.818 x 10-3

ft-lbs/sec kg-calories/min 1.945 x 10-2

ft-lbs/sec kws 1.356 x 10-3

Gallons ccs 3785gals cu ft 0.1337gals cu ins 231gals cu meters 3.785 x 10-3

gals liters 3.785gals pints (liq) 8gals quarts (liq) 4

Gallons, Imp US gals 1.20095gallons, US imp gals 0.83267

Gals Water lbs water 8.3304Gallons/Min cu ft/sec 2.228 x 10-3

gals/min liters/sec 0.06308gals/min cu ft/hr 8.0208

Horse-Power BTUs/min 42.44hp ft-lbs/min 33,000hp ft-lbs/sec 550

_____________________________________________________________CONVERSION FACTORSTO CONVERT _____INTO ____MULTIPLY BY TO CONVERT_____INTO _____MULTIPLY BY


hp hp (metric) 1.014hp kg-calories/min 10.70hp kws 0.7457hp watts 745.7

Hp-Hours BTUs 2547hp-hrs ft-lbs 1.98 x 106

hp-hrs kg-calories 641.7hp-hrs kg-meters 2.737x105

hp-hrs kw-hrs 0.7457Inches cms 2.540Inches mms 25.4Ins Mercury atms 0.03342

ins mercury ft water 1.133ins mercury kgs/sq cm 0.03453ins mercury lbs/sq ft 70.73ins mercury lbs/sq in 0.4912

Ins of Water atms 0.002458ins of w ins mercury 0.07355ins of w kgs/sq cm 0.002540ins of w lbs/sq ft 5.202ins of w lbs/sq in 0.03613

Kilograms dynes 980,665kgs lbs 2.205kgs tons (short) 1.102 x 10-3

kgs grams 1000Kgs/Sq Cm atms 0.9678

kgs/sq cm ft water 32.81kgs/sq cm ins mercury 28.96kgs/sq cm lbs/sq ft 2048kgs/sq cm lbs/sq in 14.22

Kilometers cms 105

kms ft 3281kms meters 103

kms miles 0.6214Kms/Hr cms/sec 27.78

kms/hr ft/min 54.68kms/hr ft/sec 0.9113kms/hr meters/min 16.67kms/hr miles/hr 0.6214

Kms/Hr/Sec cms/sec/sec 27.78kms/hr/sec ft/sec/sec 0.9113kms/hr/sec Meters/sec/sec 0.2778

Kilowatts BTUs/min 56.92kws ft-lbs/min 4.425 x 104

kws ft-lbs/sec 737.6kws hp 1.341kws kg-calories/min 14.34kws watts 103

Kilowatt-Hrs BTUs 3415kw-hrs ft-lbs 2.655 x 106

kw-hrs hp-hours 1.341kw-hrs kg-calories 860.5kw-hrs kg-meters 3.671 x 105

Liters ccs 103

liters cu ft 0.03531liters cu ins 61.02liters cu meters 10-2

liters gals 0.2642liters quarts (liq) 1.057

Liters/Min gals/sec 4.403 x 10-3

Meters cms 100meters ft 3.281meters ins 39.37meters kms 10-3

meters mms 103

meters/min cms/sec 1.667meters/min ft/min 3.281meters/min ft/sec 0.05468meters/min kms/hr 0.06meters/min miles/hr 0.03728

Meters/Sec ft/min 196.8meters/sec ft/sec 3.281meters/sec kms/hr 3.6meters/sec kms/min 0.06meters/sec miles/hr 2.237meters/sec miles/min 0.03728

Microns meters 10-6

microns in 39 x 10-6

Miles/Hr cms/sec 44.70miles/hr ft/min 88miles/hr ft/sec 1.467miles/hr kms/hr 1.609miles/hr meters/min 26.82

Millimeters cms 0.1mms ins 0.03937

Minutes (Angle) radians 2.909 x 10-4

Newton kgs 0.1020Ounces lbs 0.0625

ozs. gram 28.349527Ozs (Fluid) cu in 1.805

ozs. (fluid) liters 0.02957Pounds ozs. 16

lbs. kgs 0.4536lbs. tons (short) 0.0005lbs. newtons (N) 4.44lbs. gram 453.5924

Pounds/Inch newton-meters 0.113Pounds/Foot newton-meters 1.356Lbs of Water cu ft 0.01605

lbs of water cu in 27.73lbs of water gals 0.1204

Lbs of Water/Min cu ft/sec 2.679 x 10-4

Pounds/Cu Ft lbs/cu in 5.787 x 10-4

Pounds/Cu In lbs/cu ft 1728Pounds/Sq In atms 0.06804

lbs/sq in ft water 2.311lbs/sq in in mercury 2.036lbs/sq in kgs/sq cm 0.07031

Radians degrees 57.29578Tons (Long) kgs 1016

tons (long) lbs 2240tons (long) tons (short) 1.12000

Tons (Short) kgs 2000tons (short) kps 907.18486tons (short) tons (long) 0.89287tons (short) tons (metric) 0.90718

Watts BTUs/min 0.05692watts ft-lbs/min 44.26watts ft-lbs/sec 0.7376watts hp 1.341 x 10-3

watts kg-calories/min 0.01434watts kws 10-3

Watts/Hours BTUs 3.415watts-hrs ft-lbs 2655watts-hrs hp-hrs 1.341 x 10-3

watts-hrs kg-calories 0.8605watts-hrs kg-meters 367.1watts-hrs kw-hrs 10-3

CONVERSION FACTORS ______________________________________________________________TO CONVERT _____INTO ____MULTIPLY BY TO CONVERT_____INTO _____MULTIPLY BY

Documents

Apollo Tech