7/28/2019 APNEA-J-DSH-0002 Rev. 1
3/3
DOCUMENT NO: REV.
0 APPROVED FOR BID
1 RE-APPROVED FOR BID
Tag No. : APNEA-HCV-0158 Line No. : PG-102-D-8"
Service : APNE-A WELLHEAD 01 FLOWLINE Hazardous Area Class. :
Class I, Div.1, Group D, T3
P&ID No. : MIKE-APNEA-P-PID-6001 Electrical Certification :
FM/UL/CSA
FLOW CONDITIONS : Case 3 (Minimum)
1 Fluid Type Hydrocarbon Hydrocarbon Hydrocarbon2 Phase Gas Gas
Liquid Gas Liquid 3 Flow Rate 8.8 MMSCFD 15.97 MMSCFD 16.7 BPD 1.21
MMSCFD 0.57 BPD4 Molecular Weight 16.37 16.38 18 16.37 185
Viscosity cP 0.013 0.012 0.56 0.012 0.776 Upstream Density
lb/ft
3 1.849 0.433 61.8 0.418 62.597 Specific Heat Ratio Cp/Cv 1.41
1.32 N/A 1.33 N/A8 Gas Compressibility Factor, Z 0.93 0.98 N/A 0.98
N/A9 Max Shutoff dP 725 725 72510 Maximum 725 725 72511 Inlet 633.4
146.3 132.512 Outlet 132 136.3 12113 Vapor Press. N/A 4.716 psia
2.719 psia14 Critical Press. N/A 3193.5 psia 3193.5 psia
15 Design 150 150 15016 Operating 115.4 119 8917 Calculated Cv
17 (Note 2) Note 318 Predictable SPL Note 319 6220 Inlet 8", Sch.
80 63 Tag No. APNEA-SY-0158A APNEA-SY-0158B21 Outlet 8", Sch. 80 64
Valve Quantity22 Pipeline Insulation N/A 65 Manufacturer &
Model No. BIFOLD FLUID POWER or Equal23 66 Solenoid Type 3-way
Universal, Pulse operated24 Type Angle 67 Body Size No. of Ports
1/4" Three25 Inlet/Outlet Size 68 Body / Trim Material 316 SS26
Material Carbon Steel 69 Supply Voltage Power Consumption 24 VDC
3.5 W27 Pressure Class / End Connection ASME 600# - Flanged 70 Coil
Housing Class H28 Number of Ports Note 3 71 Pneumatic Connection
1/4" NPTF29 Guiding Fully Balanced 72 Electrical Connection 1/2"
NPTF30 Flow Direction Note 3 73 Protection/Enclosure Class NEMA 4X
& 731 Type MFR. STD 74 Electrical Area Classification Class I,
Div. 1, Gr. D & T332 Material Carbon Steel 75 Surge Suppression
Diode Yes33 Lubricant & Isolation Valve N/A 76 Exhaust Bug
Screen Yes, 316SS (Note 8)34 Type MFR. STD 77 Identification Plate
Yes35 Material Note 3 7836 Shut-off Class ASME/ FCI 70.2 Class V
7937 Manufacturer MASTER FLO or Equal 80 Type N/A38 Model No. Note
3 81 Manufacturer & Model No. N/A39 82 Signal Input N/A40 Type
Cage with external sleeve 83 Signal Output N/A41 Selected Cv Note 3
84 Gauges N/A42 Max. Flow for Trim Note 3 85 Elect. Area
Classification N/A43 Characteristic Equal Percentage 8644 Balanced
or Unbalanced Note 3 87 Manufacturer & Model No. PROXIMITY or
Equal45 Bean Carrier Material 316 SS 88 Tag No. APNEA-ZT-015846
Seat Material Solid 5CB Tungsten Carbide 89 Signal Output 4-20 mA,
HART Protocol47 Cage / Guide Material Solid 5CB Tungsten Carbide 90
Power Supply 24 V DC48 Stem Material UNS S17400 SS 91 Enclosure
NEMA 4X & NEMA 749 Bolting Material 316 SS 92 Classification
Area Class I, Div.1, Gr. D & T350 Seal Material Teflon 9351 94
Manufacturer & Model No. FISHER or Equal52 Actuator Type
Pneumatic, Stepping Actuator 95 Body Material Set Pressure 316 SS
Note 353 Manufacturer MASTER FLO or Equal 96 Gauge54 Model No. Note
3 9755 Mounting Vertical 98 Seat Leakage Test ASME B16.104-1976
(FCI 70.2-2006)56 Fail Position Stay-put 99 Body / Pressure Test
API 6A57 Rated Output Torque Note 3 10058 Stroking Time Note 3
10159 Pneumatic Supply Pressure Min 80 psig/ Max 200 psig 102
Tubing / Fittings 316 SS60 Handwheel Type Declutchable, Top Mounted
(Note 4) 103 Local Position Indicator Yes, Required61 Adjustable
Mechanical Limit Stop Yes, required 104
NOTES :
1. Valve and accessories shall be provided with 316 SS tag plate
with tag number and service description engraved in 0.23 inch High
x 0.01 inch Deep
bold letters tied to it by a 316 SS wire.
2. Vendor to check and confirm. The sizing calculation shall be
submitted for approval.
3. Vendor to furnish.
4. Handwheel diameter shall not exceed 2 ft (600 mm).
5. Two Solenoid valves are required, one for opening and another
for remote closing using pulse signal.
6. Valves shall be supplied in accordance with General
Instrumentation Specification (Doc. No. MIKE-J-SPE-0001).
7. Valve body and actuator shall be coated and painted in
accordance with Painting Specification (Doc. No.
MIKE-X-SPE-0004).
8. Bug screens shall be fitted to all exhausts.
APNEA-J-DSH-0002 Rev.1 Page 3 of 3
2 EA
OTHERS
TEST
6" 6"
Yes
VALVE BODY / BONNET
I/P POSITIONER
ACTUATOR
POSITION TRANSMITTER
AIR SET
TRIM
SOLENOID VALVES
13 (Note 2) Note 3Note 3
252 (Note 2) Note 3Note 3
LINE
CHK'D
WID
PREP'D
PW/JBUS
Case 1 (Early Production) Case 2 (Maximum)
19-Feb-2010 WID
APNEA-J-DSH-0002
REFERENCE DRAWING NO :
1Instrument - Data Sheet
Actuated Choke Valve
APNE-A MONOPOD PLATFORM
US PW/JB
PERTAMINA HULU ENERGI
OFFSHORE NORTH WEST JAVA
LTD.
REV DESCRIPTION
19-Jan-2010
DATE COMPAPP'D
FEED for APN E/F
New Field Development
STC - 0485
Body
Bonnet
Packing
GENERAL INFORMATION
Pipeline Size &
Schedule
Pressure, Psig
Temperature,oF
Percent Travel
