Ansys R11 Tips

7/26/2019 Ansys R11 Tips

http://slidepdf.com/reader/full/ansys-r11-tips 1/8

NSYS® Tips

SYS Tips and ANSYS Trickser Budgellrlington, Ontario, Canada

98, 1999 byPeter C.Budgell -- You are welcome to print and photocopythese pages.

e tips and comments are intended for user education purposes only.They are to be used at your own risk.The contentsare based on myexperience with ANSYS 5.3 -- more recentversions maychange things. The contents do not attemptto discussall the concepts of the finite elementmethod that are required to obtain successful solutions.It is your responsibility todetermine if you have sufficientknowlege and understanding of finite elementtheoryto apply the software appropriately. I have attempted to give accurate information,but cannotaccept liabilityfor any consequencesor damages which mayresult from errorss discussion.Accordingly, Idisclaim anyliability for anydamages including, butnot limited to, injury to person or property,lost profit, data recoverycharges, attorney's fees, or anyother costsor expenses.

ne writer putit, Thisinformation is free, and may be well worth the price.

urn to Home Page A and Optimization Introduction Page A Modeling Issues Page

e ANSYS manuals explain many things and give some examples, but they do not give many tips to the user. Here i s a collection of things I have noted or learned. (Use at your own risk...) Necessity is the mother of invention, and I learned virtually everything here as a result of need, or as a result of trial and lots of error. I'm also thankful to my local ANSYS distributor for many helpful conversations. The comments in these pagesbased on my experience with ANSYS 5.0 through ANSYS 5.3. I hope these tips will shorten your learning curve. An analyst frequently does not have a mentor for guidance, so considerable effort can be needed to deduce how to accomplish some tasks. ANSYS users need to spend a generous amount of time reading the manuals and training materials, and returning to read t hem again as the user's knowledge of the programreases. Don't use anything here verbatim... understand why it works, and whether my comments are in error or inappropriate for your situation, before employing any of these suggestions.

e teaching of FEA at the academic level is intended to educate the mind, teach how FEA methods are derived from first principles, and to develop students who can invent and code new elements, test their behavior, write research or industrial quality software, and apply it to difficult academic or research problems. Some professors feel strongly that the purpose of an undergrad course in FEA is further education in how applied math,ineering, continuum mechanics, energy methods, and analysis of structures come together, building on the Strength of Materials courses already taken -- I have no argument with that. A user with a comprehension of what underlies FEA work will know when to apply and how to evaluate FEA work, have more creativity, l earn quickly, problem solve better, be more innovative, and make fewer serious modeling errors. Thefessors do not feel that the course is i ntended to concentrate on modeling details or learning the interface to a commercial FEA program. (Students, on the other hand, want to graduate having used an FEA package to do something significant. Assignments and projects with ANSYS/ED are a good way to get there.) I've heard the opinion expressed that with FEA technology maturing, there is less research grant money for FEA workniversities, and the supply of advanced FEA graduate students may be shrinking. The teaching of commercial FEA program use is principally focused on training people to use the interface to and commands of the particular software package, and how to perform basic analysis types. Some instructors pepper their presentations with tips, but the attendees may be drowning from information overload. Little is available to l ead the user through the techniques that can bed in modeling complex structures, and around the traps that exist, except help from good vendor support people, co-workers, or other users, and substantial reading, thought, trying examples, and testing techniques on the part of the analyst. I hope that these pages will provide some helpful details.

NTENTS:

Tip 1: Use AnnotationsTip 2: Making Room for AnnotationsTip 3: Using Parameters in AnnotationsTip 4: Use Small AnnotationsTip 5: Mathematical Functions AvailableTip 6: Start 16-Bit Applications before Starting ANSYS under Windows NTTip 7: Running ANSYS at Low Priority under Windows NT 4.0Tip 8: Operating on (Scaling) LoadsTip 9: Ramping Loads Down to ZeroTip 10: Starting ANSYS Graphs at t=0Tip 11: Pressure on Lines

Tip 12: Ramping Some Loads, Not OthersTip 13: Force and Pressure on Flat Plates or Flat ShellsTip 14: Linear and Nonlinear BucklingTip 15: Nonlinear Analysis and the Arc-Length MethodTip 16: Animating Results from a Nonlinear or Other AnalysisTip 17: Getting the Mass or Weight of a ModelTip 18: Using Fnc Calls f rom MacrosTip 19: Use ENSYM and ENORM t o Turn Over Shell ElementsTip 20: Shell Types to TryTip 21: Moving a Model from ANSYS Mechanical to ANSYS Linear/PlusTip 22: Deleting Nodes with Nodal CouplingTip 23: Convergence with Shell Finite Element Models in Nonlinear Analysis under ANSYSTip 24: Working with Load Step Files in ANSYSTip 25: Plotting Shell Stress -- Surface, Mid-Plane Stress, Load Paths, ESYS and RSYSTip 26: Nodal Coupling (CP) versus Rigid Region (CERIG)Tip 27: Vibration Modes with Pre-stressTip 28: Creating New Elements by Copying or Reflecting Existing StructureTip 29: Adding to a Model Comprised of Elements and Nodes OnlyTip 30: Zero Mass Beam Elements Form Rigid RegionTip 31: Turn off Symbols When Changing a Model after SolutionTip 32: Are the "Free-Free" Vibration Modes Relevant?Tip 33: Selecting a CAD or FEA System -- Cover YourselfTip 34: Creating Lines Perpendicular to, or at Angle to Existing LinesTip 35: Use the /UI command in Your ANSYS Toolbar to Bring up GUI Dialog BoxesTip 36: Reaction Force, Nodal Force, and Load PathsTip 37: Inputting Temperatures with BF, BFE, and TUNIF in Structural AnalysisTip 38: ANSYS Toolbar UseTip 39: ANSYS Piping Element LengthsTip 40: Graphical Output from ANSYSTip 41: Check Nodal Loads at Bolts, Rivets, Spot Welds and LinksTip 42: Use QUERY to Check Results with PickingTip 43: Loads on Geometric EntitiesOverwrite Loads on Nodes and Elements -- Easy Error to MakeTip 44: Use Components for Load Input, and for Results ReviewTip 45: Simple Substructuring Examples -- Bottom Up and Top DownTip 46: Plot Applied TemperaturesTip 47: Skipping Over Statements in an Input FileTip 48: Static Analysis Followed by Transient AnalysisTip 49: File Compression for Model StorageTip 50: Organizing Large FEA ModelsTip 51: Selecting Nodes in a Stress or Strain RangeTip 52: Selecting Nodes that are Subjected to Nodal CouplingTip 53: /NOPR and /GOPR Speed Up Input Files and MacrosTip 54: Using Commands IMMED and /UIS and /SHOW,OFFTip 55: What's the Bauschinger Effect? Comments on Material YieldTip 56: Thought ExperimentsTip 57: Control of MeshingTip 58: Four View PlotTip 59: Quick Review of Mode ShapesTip 60: Using ANSYS HelpTip 61: The FEA Job HuntTip 62: *VPUT and DESOLTip 63: How to Divide One Element Table Column by AnotherTip 64: Element Tables (ETABLE) and Arrays -- An Example

Tip 65: Error Estimation, PowerGraphics, and ERNORMTip 66: Concatenate and Mesh LastTip 67: ANSYS Output of Data to Files for Use by Other ProgramsTip 68: Writing Array Columns to Output or to FilesTip 69: Synthesizing Parameter Names and Manipulating Jobnames and Long Strings in APDLTip 70: Solid Elements 95 and 92 -- Efficiency and Interconnection

1: Use Annotations:

ly a one-line title is possible on the ANSYS screen or plot. Considerably more information can be included in annotations on the screen. The annotations are kept through all plots until they a re deleted with the command: /ANNOT,DELE or via picking with the graphical user interface (GUI).

he top of the Annotation dialog box, there is a list box from which the user can choose Text, Lines, etc., on down to Controls. These selections bring up different menus. The Controls selection offers a SNAP setting that makes it much easier to get the text aligned nicely. (Hint: ANSYS, Inc. should put this SNAP selection up front under Text, or even on every menu.) Activate the Snap setting, t hen go back to Text to enter the annotations.

2: Making Room for Annotations:

e /PLOPTS command controls what goes into the legend at t he right (by default) side of the ANSYS screen and plot. If you turn off LEG2 (the relatively useless "view" information), you will get extra room at the bottom of the legend. This area can be used for annotations if the number of contour levels in stress plots is not too great (the default is fine).

3: Using Parameters in Annotations:

t as in a t itle created with the command /TITLE, ANSYS permits the use of a parameter in an annotation, as discussed in the Commands Manual description of the /TLABLE command. When typing the annotation using the GUI, include t he parameter in percent signs like t his: %pname% where pname is the parameter name. The parameter can contain either numbers or text. The value of the parameter will be plotted in the annotation string. The ANSYS functionNT can be used to round a number the nearest integer, sometimes improving the appearance of the annotation for large numbers in which the fractional part is irrelevant (e.g. NINT(123.456789) = 123 ). For this, the parametric expression should be enclosed in percent signs. Annotations are usually created in the GUI, but can be entered with code like that shown below. Entering a single annotation line containing Result = %pname% generates log file contents such as:

! The following commands place an annotation on the screen.! For information only. Use at your own risk.

! In this example, "pname" is a parameter with a numerical value such as 123.456789/ANUM ,0, 1, 1.2303, -.74699

/TSPEC, 15, .600, 1, 0, 0/TLAB, 1.010, -.747,Result = %pname%

e last line in the above example contains the string that the user types manually. The other data set up the string positioning on the screen, and the properties of the characters. To apply the NINT function to the parameter, manually e nter Result = %NINT(pname)% as the annotation:

! For information only. Use at your own risk.! Type the annotation in one line, so the log file contains:

/ANUM ,0, 1, 1.2303, -.74699/TSPEC, 15, .600, 1, 0, 0/TLAB, 1.010, -.747,Result = %NINT(pname)%

e beauty of doing this is that if the value of the parameter pname should change, then when the next plot command is executed, the annotation will automatically update to reflect the new value! Try it: after creat ing an annotation on the screen that includes a parameter, change the parameter's value, then do a / REPLOT. Running a macro could get information that goes into the parameter that a /REPLOT will automatically put i t on the screen. This makes it possibleutomatically include far more information than can go i nto the title, and to do it for a series of automatically generated plots or graphs.

4: Use Small Annotations:

e default character size setting for an annotation is 1. The size of an annotation can be decreased using the GUI. A size of 0.6 is quite readable and permits far more information to be packed into a plot. Note that there is a limit to the number of characters possible on an annotation line – this is character size independent.

5: Mathematical Functions Available:

der the Help listing for the *SET command there appears li sts of mathematical functions available in ANSYS. Another list is in the ANSYS User's Guide on APDL, Chapter 14 of t he Modeling and Meshing Guide. The commands are usable anywhere. They include:

te:

The function form of the *GET commands can also be used to get information from the model -- see t he APDL guide mentioned above for a listing of available functions. The APDL guide also gives functions to retrieve the values of parameters, both numerical and character. The *VFUN command has a list of functions that act on an array entry. The Commands manual lists functions that act on Element Tables in the section "POST1 Command for ElementTable". Creatively used, the array and ETABLE algebra commands can be surprisingly powerful.

6: Start 16-Bit Applications before Starting ANSYS under Windows NT:

as been my experience that some large commercial 16-bit applications will not start properly when ANSYS is already running. If you start them before launching ANSYS, there will be no problem. If you intend to work with those 16 bit applications in the foreground while the ANSYS SOLVE is running in the background, this will be a useful tip. I have seen other applications start up very slowly (e.g. Internet Explorer) or wait until ANSYS was done beforeceeding (setup.exe for many Windows install programs).

7: Running ANSYS at Low Priority under Windows NT 4.0:

der Windows NT 4.0 the priority level of individual processes can be user-adjusted. To do this, bring up t he Task Manager (right click on the Windows NT taskbar), and click the tab for "Processes". Right click on t he process titled "ANSYS.EXE", and "Set Priority >" comes up. Set the priority to "Low" t o help make foreground applications run more smoothly while ANSYS is runningLVE in the background. This may help more if you have a l arge RAM in the computer.

en ANSYS has completed the SOLVE process, return the priority to "Normal" so that ANSYS is not slowed down when you start doing plots through the GUI.

8: Operating on (Scaling) Loads:

u can operate on loads on nodes and elements in order to scale them up or down. Unfortunately, scaling loads on geometric entities (keypoints, lines, areas and volumes) seems not to be available. If any load on your structure has been applied to a geometric entity, rather than directly to ele ments or nodes, that load will be transferred to the elements and nodes at solution t ime. The transferl overwrite any scaling of loads that you have applied. (Guess how I figured this out!)

what can you do about this? Method 1: Transfer the loading from geometric entities to the elements and nodes, then write a load step file. This records loading on elements and nodes. Delete the loading on geometric entities, then read the l oad step file that was just written. Now the loading can be scal ed up or down freely. Method 2: For a faster method, see the "LSCLEAR,SOLID"mmand, which will not require writing a load step fil e. Method 3: Transfer the loading from geometric entities to the elements and nodes, then delete the relationship between geometry and the FEA mesh with the MODMSH,DETA command. Method 4: Transfer loading from geometric entities to the elements and nodes, then un-select the geometric entiti es, before executing SOLVE. Thement and node loading can be scaled after it has been transferred from geometric entities. An un-selected geometric entity will not transfer its loading to elements or nodes when SOLVE is executed. Warnings: Method 3 ruins the relationship between geometry and the mesh. Save the model under an appropriate file name before executing MODMSH,DETA. Method 4 is fine, as l ong as younot forget and re-select the geometric entities -- ALLSEL will do this.

ling displacements (nodal constraint values) is also possible. One thing that has not worked for me is an at tempt to reduce applied displacements to zero by using 0.0 as the scaling factor. What did work for me was to use "_TINY" as a value, which multiplied displacements by a factor of roughly 10^(-31) and reduced loads to virtually zero. Attempts to use 0.0 as the factor resulted in NOnge to the applied displacements.

9: Ramping Loads Down to Zero:

ou are ramping force, pressure, and acceleration loads up and down as part of an analysis, you may want to return loads to zero. I do this when I want to inspect permanent deformation that results from plastic yielding. If you delete the applied load, the loading will drop immediately to zero, even if you have l oad ramping turned on. The thing to do is to set the loading to virtually zero or theling factor to virtually zero, not delete the load. It is important to appreciate that to ANSYS, reducing a load to nearly zero is not the same thing as deleting it (zeroing it), for the purposes of ramping loads. The time substep sizes to use will depend on your model.

ting displacements to zero or near zero i s, of course, very different from deleting constraints.

10: Starting ANSYS Graphs at t=0

aphs start at the first data point, which means that if you do a time-history trace, you don't get a t=0 data point. If you leave time as 0.0 on the TIME command, you get the default 1.0 in your output. The only way to get a graph from zero that I have found is to do a first load step with "t" extremely small, in comparison to other times in the analysis, e.g. t=0.0000001. The load at this time must be appropriate so that the response ramps up correctly. (If your intent was tomp up from zero load, just leave the loads as zero.) The next load step continues as usual.

11: Pressure on Lines:

plying pressure on a line results in loads being applied to the nodes associated with that line. The loads on the nodes that the FEA program applies will be appropriate given the formulation of the elements. If you want to apply a total force to the line, you can use a *GET command to find the length of the line, then divide the force by the length and use the result as the pressure.

te that pressure on a line act s in the plane of t he area that is attached to the line. If two areas are attached at 90 degrees or another angle, two loads are set up, acting in each of the area plane directions. You can use select logic on the areas to get some interesting effects as t o the direction in which the applied forces act, but only if both areas a re meshed, and the elements are sele cted. If you un-select one of the areas, pressure on the line will only be exerted in theection of the area that i s selected. The select logic must still be in place when you SOLVE, or else your carefully crafted load case can be overwritten. As above, transferring loads from geometric entities to nodes and el ements, writing them as a load step, deleting all the loads on geometric entities, and reading in the load step will protect your load case, and make scaling the loads possible. Alternatively, consider the " LSCLEAR,SOLID" command.

TE: Pressures on surfaces follow the deformed shape during a Large Displacement (geometrically nonlinear) analysis. Forces on nodes maintain their orientation in space, even under Large Displacement. This difference will govern how loads should be applied in some models.

12: Ramping Some Loads, Not Others:

hold some loads constant and ramp up or down others, run a first load step with all t he loads at their starting values, ramping from zero only if appropriate.

ou want, use an extremely small value on the TIME command, e.g. 0.0000001, and run this as a first load step. Then set up a second load step, with ramping activated. Change those loads to be ramped from their starting values to new values. Hold the other loads constant. The TIME command can be used with a new value, such as 1.0.

example is the application of a gravity load before other loads are to be ramped up from zero. In some cases, this could give a more realistic assessment of nonlinear buckling caused by applied forces other than gravity l oading. (You will want to check the codes that regulate your design work before deciding on this. Codes that I have seen were generally started before FEA was widely available, and do not address this concept. Find out what is considered goodctice in your industry.) Applying gravity first can give much better convergence when assessing the effect of t hermal expansion moving structures across friction contact elements, where the normal load on the contact elements is caused by gravity.

spect that this is not possible with the Arc-Length method. I have not experimented with it, but do not see how controlled ramping of only some loads could be implemented under Arc-Length control of applied loading -- any opinions?

13: Force and Pressure on Flat Plates or Flat Shells

BS(X) Absolute value

COS(X) ArcCosine

SIN(X) ArcSin

TAN(X) ArcTangent

TAN2(X,Y) ArcTangent of (Y/X) with the sign of each component considered (see aFORTRAN manual if you don't know what this means.)

OS(X) Cosine

OSH(X) Hyperbolic cosine

XP(X) Exponential

DIS(X,Y) Random sample of Gaussian distributions where X is the mean, and Y is thestandard deviation. Might be used in a Monte Carlo Simulation to explore thedistribution of outputs based on randomized loadings and material properties.For an explanation, see a good modern engineering design textbook.

OG(X) Natural log (to base e)

OG10(X) Log (to base 10)

OD(X,Y) Modulus (X/Y), it returns the remainder of X/Y. If Y=0, returns zero (0)

INT(X) Nearest integer (nice for outputs of stresses to /TITLE or annotations (see Tip3 above))

AND(X,Y) Random number, where X is the lower bound, and Y is the upper bound.(Useful for Monte Carlo Simulation, etc.)

IGN(X,Y) Absolute value of X with sign of Y. Y=0 results in positive sign.

IN(X) Sine

INH(X) Hyperbolic sine

QRT(X) Square root.

AN(X) Tangent

ANH(X) Hyperbolic Tangent

Page 1 of 8SYS Tips and ANSYS Tricks

9/10/2007p://www3.sympatico.ca/peter_budgell/ANSYS_tips.html



ere is a rule of t humb, that if the out-of-plane deflection of a flat plate or shell is greater than half the thickness, then membrane forces start to become significant in resisting the applied load. In ANSYS, this calls for activating a Large Displacement solution (a.k.a. geometric nonlinearity). Ignoring this can result in your design missing out on inherent strength, OR in grossly inadequate underdesign. Know what you are doing.

14: Linear and Nonlinear Buckling:

ear eigenvalue (classical Euler) buckling is a "quick" check on a structure, but the ANSYS manuals go to considerable pains to point out that in many situations, a Large Displacement solution (geometric nonlinearity) needs to be run also as a check on the buckling adequacy of a design. As with linear buckling, nonlinear buckling may need to be assessed with respect to a number of load cases. In some structures, a diagonal tension field is developed in a web, andtic buckling failure does not develop at the first eigenvalues predicted. In other structures, buckling failure may occur before the first ei genvalue, and only nonlinear analysis will predict this.

ear eigenvalue buckling has to assume that gap and contact elements are either closed and acti ve, or open and inactive. Nonlinear analysis will follow the effects of these elements as they go in and out of contact, when t he loading is applied.

er any Large Displacement nonlinear elastic buckling analysis (if it doesn't diverge), see whether the elastic stress l imits have been exceeded (this includes the surfaces of shell elements, and be careful t hat nodal averaging does not hide anything). If significantly overstressed, the structure may not be adequate.

mbined bending and axial compression in a beam is a cl assic place where inadequacy in strength can be predicted in FEA only by Large Displacement nonlinear analysis (i.e. a linear analysis says it is OK, but a nonlinear analysis shows it is NOT). For some structures undergoing elastic Large Displacement analysis without contact and gap elements, the user may want to consider a Southwell plot.

lastic stress limits are exceeded in the Large Displacement model, i t may be desirable to do a combined Large Displacement and Plastic Deformation model. If the structure is overloaded, it may begin to collapse (perhaps only locally), and the Arc-Length method may be needed for convergence control. A need to strengthen the structure may be predicted or identified. The material properties to use are application domain and industry specific -- start by talking to yourworkers, supervisor, and suppliers.

15: Nonlinear Analysis and the Arc-Length Method:

e basic way to do nonlinear analysis in ANSYS is to use NR iteration and many default settings. At times, convergence will become a problem; I've encountered this with shell structures under compressive stresses. The arc-length method can sometimes cope better with nonlinear solutions, because of its ability to follow force-deflection curves that rise and fall. Be prepared for long run timesour model is large.

experience with the arc-length method is that i n its default settings for step size multipliers, it does not give satisfactory results when compressing some shell-based models. What may work is to set a number of time substeps, such as 10, so that each substep is 1/10 of the load step. Set the Arc-Length maximum multiplier MAXARC to 1.0 so that no substeps larger than 1/10 of the load steptaken. Set the Arc-Length minimum multiplier MINARC to 0.1, so that the smallest load substep is 1/100 of the full load step. I found this t o help considerably. You may want to user a larger or smaller MINARC setting, but my experience to date suggests that one should not get greedy with MAXARC. Obviously, you may want to play with the number of time substeps.

e solution may still diverge but it is likely that you will get more information than without arc-length analysis. You will want to set a termination condition for the analysis if buckling is expected to result.

nd it desirable to sa ve the results at every t ime substep when doing this type of analysis (it helps to have a large hard drive) in order to review the process. When you review the results of a single load case run under Arc-length control, the TIME value on the ANSYS plots shows the decimal fraction of the fulld being applied to the model. As you move forward through the plots, if the load/displacement curve for the structure is falling, the decimal fraction will fall, even though some displacements are visibly getting larger.

mentioned above, something I have not tried is to get the Arc-length solution control to ramp some loads and not others, by having run a preliminary load step. Is this even possible? If not, then the user may face the prospect of gravity being ramped up and down, in addition to other applied loads, and theysical realism of the model may be affected.

16: Animating Results from a Nonlinear or Other Analysis:

an be helpful to watch the increasing stress levels that result as a nonlinear analysis loading is ramped up. To create an animation, first run your analysis with loads ramped up, and a number of substeps. Have all substeps written to the results file. Do a stress plot of interest to set the type of st ress plot to bemated by the macro that will be run. Make the ANSYS Graphics window as small as you want the animation window to appear (most screens will have l ower resolution than a CAD workstation), keeping the aspect ratio correct. Smaller graphics windows result in small er animation files, if size matters.imation files under Windows NT (AVI files) from ANSYS often compress very well for storage purposes. Use the PlotCtrls menu selection on t he Utility Menu, and choose Animate to get a sub-menu of choices. Choose "Dynamic Results" to create an animation of your saved load substep results with the time

wn in the legend. This seems to work only for the last load step (read the ANSYS macro). The resulting AVI file can be viewed with the media player, distributed, put on a web sit e, and so on. The media player can be stepped manually for slow viewing. It makes it easier to watch the changing stress pattern orormation as nonlinear effects take over the model.

nimating a changing stress or other contour plot, you may wish to specify the contour levels before generating the animation file. View the load step or substep with the worst results as part of deciding where to set the contour levels.

ve not found that any of the ANSYS supplied animation macros do the one simplest thing I want. Usually I want to animate every substep of every load st ep stored in the results file. The following simple macro does this for me under Windows NT. There is virtually no error checking in this macro. Note that thisple macro does not update element table data at each frame. Consequently it will not work properly for plots of element table data. If stresses, strains, or other data with amplitude information are to be plotted, the user may want to fix the contour map levels ahead of time. The user will want to set the

placement amplitude scaling with /DSCALE in advance--automatic scaling will not be satisfactory. In general, it may not be satisfactory to have /ZOOM,OFF active, since the view will change if plots of significant deflection are included in the animation. Manually setting a view may yield a better animation.dify this macro as you wish.

s macro must be called from within /POST1. The file that contains the results must have already been selected, and a prototype plot command executed so that calling /REPLOT will generate the type of plot the user wants:

! --------------------------------------------------------------------! MY_ANIM.MAC A quick-and-dirty animation of all of the substeps

! --------------------------------------------------------------------! For information only. Use at your own risk.

! User must indicate how many frames are to be animated! This macro starts with the first substep in the results file! by using the SET,FIRST command internally

! User implicitly indicates how many times to use the SET,NEXT command.! The number of frames needed must exist in the RST file, else errors.

! NOTE: This does NOT work for plots of data in an element table.! Plotting element table results would require a macro in which

! the element table results are updated at each substep.!! Virtually NO Error Checking Is Performed ! ! ! ! !

!! What will be plotted is based on /REPLOT therefore, on the last user plot executed

! before this macro is called.! Scaling, etc. are all based on the last user plot. Only the SET value is updated.

!! Call with:

!! my_anim, time_delay_for_frame, number_of_frames_including_first!

ar11=arg1*if,arg1,eq,0,then

ar11=0.1*endif*if,arg2,ne,0, then

/NOPR/gsav,xxx,gsav,,temp

/seg,delete/seg,multi,,ar11

set,first/replot*do,_iii,1,arg2-1,1

set,next/replot

*enddo/seg,off

anim,1,1,ar11/gres,xxx,gsav/gopr

*endif

alternative to this macro could step through all substeps on the RST file by using a *GET command of the type *GET,NTOTAL,ACTIVE,0,SOLU,NCMSS to check the number of substeps as the SET,NEXT command is issued. The parameter NTOTAL will be re-set to 1 when the animation is complete, and the *IF and *EXIT commands can check this and break out of a do loop -- see Tip 59 below for the example of automatically plotti ng all mode shapes. The useruld then not need to specify the number of substeps to plot, i mproving the automation, and letting the solver use variable substep sizes without the user having to check on the number of substeps that resulted.

17: Getting the Mass or Weight of a Model:

eader has been helpful by pointing point out that mass (or weight, depending on your units) of keypoints, lines, areas, or volumes in a model can be retrieved, when attributes have been assigned to these entiti es, by using commands available in /PREP7. Using the graphical user interface, enter into "PreprocessorOperateCalc Geometric Items" to see the choices: " Of Keypoints, Of Lines, Of Areas, Of Volumes, Of Geometry". These items execute t he "sum" commands:SUM, LSUM, ASUM, VSUM, GSUM" respectively. If no attributes have been assigned to the geometric entities, unit densities are assumed in reporting mass and center of gravity information. After the execution of these commands, the *GET command can be used to assign t o a variable the implied volume of an area (based on the thickness associated with its attributes) or the volume of a "volume". The volume of a series of areas or "volumes" can also be retrievedh the *GET command after a "sum" c ommand is used. The *VGET command can also be used, where appropriate, in retrieving information made available after one of the "sum" commands is executed.

some unstated reason, ANSYS will not directly give the t otal weight or mass of a model (retrieved from the mass matrices of the elements), except to print it to output during the solution of a problem. The user can run a partial solve in order to get this weight or mass printed reasonably quickly. In Imperial units, it may be desirable to convert between pounds mass and pounds weight. There is no *GET command that directly returns the weight of selected elements.wever, the volume of an element can be returned, and the volume of a set of elements can be put into an el ement table, and summed.

u can get the weight of many models into a parameter by: step through all material types, selecting elements for each material type. Get the volume of those elements, and multiply by the density of that material type. Sum the masses or weights of all the material types. This will not include added mass and mass elements at nodes (check this carefully against the output mass i n the solve module) or other things that I may not have thought of.

course, you can get the weight (assuming you gave densities in the material definitions) by removing all loads (don't let thermal expansion, nodal rigid region, nodal coupling, various gap and contact elements, or loads on constrained nodes trip you up -- use t he minimal constraints needed to stabilize all bodies in 3-D), applying 1 g vertical, having constraints on vertical motion, running SOLVE in a linear analysis, and finding the vertical reaction force. In such a run,ombination of the FSUM (select vertically restrained nodes only, with all attached elements) and *GET commands in /POST1 might help you to get the weight into a variable. However, a partial solve will give the answer more quickly (but not put it into a variable). Depending on your system of units, remember, you may want to convert between weight and mass.

se my comment, about the inability of ANSYS to directly return the weight of the model with *GET, on comments in the manuals on Optimization. The optimization examples work to reduce model volume, not weight.

18: Using Fnc Calls from Macros:

fore using macros for the first time, read about the *USE command in the ANSYS Help manual, in addition to other relevant parts of the ANSYS manuals. The *USE command help discusses the macro call ing parameters and their local scope. Note a slight difference in calling parameters AR19 and AR20 when the *USE form of a macro call is used, versus the "unknown command" form.

ere are times when calls from macros directly to the Function form of an ANSYS command will be the only way to get the function called with picking. It may be desirable to sent the user a message that explains why the picking has been requested. The function must be called with the exact use of upper case and lower case characters. An example: Fnc_ENSYM will work, whereas fnc_ENSYM will not, because the capital F is missing.

19: Use ENSYM and ENORM to Turn Over Shell Elements:

SYS has two commands, ENSYM and ENORM, for re-orienting shell elements so that a set of shell elements can all have their "top" surface face t he same way. This makes application of pressure, contact el ements, and review of results more feasible. This orientation should be done before running SOLVE; the results are not re-oriented in the database when these commands are applied, nor in the results file, so if the elements are re-oriented after SOLVE, the stressults will no longer apply to the c orrect shell surfaces and a meaningless mess will result. These commands work with shell elements that are attached to areas, as well as with independent shell el ements. Note: If you clear the el ements attached to an area, t hen re-mesh, the new elements will have t he same orientation as the area. (Hint: ANSYS ought to do this re-orientation for Areas, making it easier to pressurize the interiors of containers defined with shell el ements.)

HELP,ENSYM for information on what this command will do. ENSYM can be used to "flip over" a shell element so that the opposite side (Top or Bottom) is showing. To do this would require reversing the node order in the database so that Face 1 (Bottom) and Face2 (Top) get switched.

more powerful capabilities in re-orienting shell elements, see HELP,ENORM. This command will search outward from a chosen element that the user considers "correct", re-orienting a connected set of shell elements so t hat they face the "same way" (this takes some interpretation), even working around corners. It searches elements from the selected set of elements, until it hits the edge of the model, or until two or more elements are attached to one element edge.e user should experiment with this command in order to understand exactly what it does, and inspect the model thoroughly after ENORM is applied, to verify that t he results are as desired. The correct use of ENORM can make the application of pressure or contact elements to a complex model substantially easier.

ould be very helpful if ANSYS had a special command that would plot shell elements with the sides colored according to whether they were FACE1 or FACE2 of the element. This command could be extended to color the (up to) six sides of solid elements, according to their face number. A similar command for plotting areas would help, too. It could even be done for beams displayed with /ESHAPE showing the outer envelope. At present, with ANSYS 5.3 runningWindows NT, I get different colors for Face 1 and Face 2 of shell elements when PowerGraphics is ON, and "No Numbering" plus "Colors" or "Colors and Numbers" has been chosen under PlotCtrls,Numbering. I have not seen this documented. This does not happen for areas, or for solid elements.

20: Shell Types to Try:

ve used Shell 63 (for Elastic), Shell 43 (for Plastic), Shell 93 (8-Node, for Elastic & Plastic), Shell 143 (for Plastic), and Shell 181 (for Plastic). The Revision 5.4 for ANSYS will include a bug fix for a Shell 181 problem. Shell 143 is no longer supported, but is still embedded (hidden) in Revision 5.3 of ANSYS for compatibility reasons.

ve recently found Shell 93 to be useful in modeling some curved structures, because of its ability to follow curved surfaces. (Shell 63 elements are flat, and can make a mess of a general curved surface under free meshing.) Shell 93 gave me good convergence for both elastic and plastic Large Displacement (nonlinear geometric) analysis. It does not like to follow too large an angle of curvature with one element, so the number of elements on an area fillet can be l arge.the angle subtended by Shell 93 elements during meshing to a value that is small enough to avoid warning messages. Watch out for aspect ratio warnings. (Lack of warnings is not a complete guarantee of acceptable element shapes.) If the structure has pressurized flat surfaces, Shell 93 often converges better when stress stiffening is activated for Large Displacement analysis. Stress stiffening for Shell 93 is activated at the solution phase of the analysis, whereas Shells (apparently) only stress-stiffened by setting one of the KEYOPT values. (I have obtained different Large Displacement convergences with Shell 63 with no stress-stiffening set, with the KEYOPT stress-stiffening set, with stress-stiffening set in /SOLU, and with stress-stiffening set in both places.) Like Shell 63, Shell 93 also has the virtue of being supported by the Linear/Plus version of ANSYS for Large Displacement elastic analysis, so models can be movedk and forth.

en forcing mapped meshing of curve-sided Shell 93 elements on a plane area by concatenating perimeter lines, I have occasionally had mid-side nodes created, in the interior of the area, such that there was too much element curvature distortion in the plane of the element. One fix i s to have the elements created with the sides straight, which i s tolerable if the el ements are flat, and if it does not cause trouble on the perimeter of the plane area being meshed. "Trouble"e means poor representation of curved boundaries--other elements on these boundaries may need to curve to follow curved surfaces, or it may be desired to have a curved fit to an outside edge. If flat element sides cause trouble on the perimeter, then start by meshing areas on the other side of the perimeter with elements that have curved sides--these elements could even be triangular. Next, mesh the area of interest with the elements sides set straight, then clear therounding areas, if the surrounding areas are not intended to be meshed, or need better element shape control. This will leave the plane area of interest meshed with elements that have straight edges in the interior, and curved edges on the perimeter. This is illustrated by the following images of an intentionally e xtreme example. In the first image, a line plot of element edges shows extreme distortion in the plane. An intended hole is meshed with triangles. All thesements are Shell 93, having mid-side nodes.

he second image, meshing with mid-side nodes positioned on straight lines is being chosen.

he third image, the consequence of meshing the part with straight-sided elements is shown. The elements at the hole have a curved side, because t he hole is already meshed with curved-sided elements.

he fourth image, the elements bordering the hole are shown, after the hole has been cleared of elements. The element curvature at the hole is visible. The interior of the plane area is meshed with straight-sided elements. The same problem and a similar fix can be encountered with mid-side noded SOLID95 brick elements that have 20 nodes. The surface areas of a volume can be meshed with 8-node SHELL93 elements with curvature, then the volume meshed withLID95 elements with the sides straight, then the shell elements on the areas removed with the ACLEAR command. This will leave the volume meshed with SOLID95 elements that are curved on the surface areas, but with straight sides in the interior. There are rare occasions when this will eliminate element distortion warning messages.

21: Moving a Model from ANSYS Mechanical to ANSYS Linear/Plus:

cause versions of ANSYS sell for different prices, a company may own one version to be used for nonlinear models, and several licenses for linear work, or just for model creation and results review. Occasionally, a model will be moved "down" from a fuller version of ANSYS to the Linear/Plus version.

ser can run into difficulty moving a model from ANSYS Mechanical (or ANSYS Structural, etc.) to the less expensive ANSYS Linear/Plus. The Linear/Plus version limits the number of nodes allowed. Unfortunately, it implements this control by not allowing node numbers that exceed a limiting value. This means that compression of node numbers (and element numbers) may be required in order to get larger models to be accepted by ANSYS Linear/Plus.herwise, the program quits without an opportunity to compress the numbering (more recent ANSYS versions may be more tolerant, but the numbering will have to be compressed at some point).

en the node and element numbers are compressed, coordination of loading with the numbering expressed in load step files is lost. The way around this that I have used is to read in the original database, read in a load step file, compress the numbering, and write the l oad step file. The process, reading in the original database, must be repeated for every load case (a macro could be written to automate this.) Finally, the original database is read in, numbering ismpressed, and the new database is written.

supported element types cannot be used in ANSYS Linear/Plus; neither can too large a wavefront (can the PCG solver get around this?). The unsupported elements need to be deleted or changed before moving the model (e.g. change SHELL181 to SHELL63). Then, if the number of entities does not exceed ANSYS Linear/Plus limitations, t he database can be moved to the other program.

e next problem in moving models to ANSYS Linear/Plus, is that nonlinear material models must be deleted in ANSYS Mechanical (Structural, etc...) before moving the database t o ANSYS Linear/Plus. This is because the ANSYS Linear/Plus program will complain that the material nonlinearity is included, but not a ccept the commands to delete it (Hint: ANSYS should add this delete function to Linear/Plus.) Of course, I found all this out the hard way.

rare occasions, a model from a more recent version of ANSYS may be moved back to an earlier ANSYS version. If IGES is not satisfactory, a user could use CDWRITE to write out the element and node model and other model data to a file (the DB option), then manually clean up the file so that the earlier version of ANSYS could accept it. This includes modifying commands for element creation, after deducing what format is needed. Writing the element data withWRITE then cutting and pasting with the CDWRITE file may be easier -- I haven't tried it. A user-written program can expedite cleanup for a large model.

22: Deleting Nodes that have Nodal Coupling:





en deleting a set of nodes for which some were members of coupled node sets, delete the coupling equations BEFORE deleting the nodes. Otherwise, unwanted coupling equations may be active if you create more nodes. The coupling equations are not automatically deleted when the nodes are deleted--is this a bug? Select the nodes to be deleted, then delete node coupling equations for which any nodes are selected, t hen delete the nodes. (You will have had to firstete the elements.) Clearing solid model entities is the same as deleting the elements and nodes simultaneously.

nd it very helpful to turn on the symbols for nodal coupling when checking for proper use of these details.

23: Convergence with Shell FEA Models in Nonlinear Analysis under ANSYS:

st, remember that there are three basic kinds of nonlinearity: (1) Large Displacement (geometrically nonlinear) analysis, and (2) Plastic Material properties are the obvious types. In addition, nonlinear solutions occur (3) when nonlinear elements such as gap elements, hook elements, and surface contact elements are used. Because of (3) it is clearer to refer to a "linear" analysis as "small displacement elastic", si nce "linear" may be perceived as meaning that there are nonlinear elements present. A nonlinear analysis will take longer, usually considerably longer, than a l inear analysis. For a large finite element model, it helps to have a computer with an extremely fast CPU, large RAM, large hard drive, and fast hard drive data transfer (high-speed SCSI may help on PC's) for nonlinear analysis.

ANSYS, the Shell 63 element will do Large Displacement, but is NOT capable of material nonlinearity (plasticity). Shell 43, Shell 143, and Shell 181 are capable of both Large Displacement and material nonlinearity. These four elements are 4-node quad elements. ANSYS also has an 8-node shell element, Shell 93. The Shell 93 element is capable of both Large Displacement and material nonlinearity. Shell 93 has the advantage that it can follow a curved surface.ere are also shell elements for composite materials and for P-element solutions. I will restrict my comments to the basic shell elements: 63, 43, 143, 181, and 93.

e elements should have acceptable aspect ratios, not be ridiculously large or small, not be pathologically deformed, and not generate warnings about being warped. If warped quad elements are unavoidable during meshing, it may be desirable to use either small triangles, or the Shell 93 element. Note that within the ANSYS manuals, high order elements are not considered to be ideal for nonlinear work. However, I seem to have had some success with the Shell 93ment (can't say if the results were ideally accurate). You can evaluate the model quickly by doing a partial solve (Partial Solu in the GUI), only generating the element matrices, and getting warnings (if any) and other information in the ANSYS Output window.

Large Displacement solution is chosen, some solutions are improved by setting Stress Stiffening before running the solve process. Stress stiffening for elements 63, 43, 143, and 181 can (apparently) only be set with one of the KEYOPT values (Keyopt(2)) for the element (see Options when using Add/Edit/Delete to add element types with the GUI). Some beam elements are like t his, too. It apparently (I find the manuals difficult to interpret on this) can NOT be sethin the Solve module, even though the GUI has a sel ection box for Stress Stiffening. However, I seem to have had convergence differences with Shell 63 with stress-stiffening set and not set in the solve module. For Shell 93, stress stiffening IS set within the Solve module, by choosing it under Analysis Options in the GUI (SSTIF). The use of stress stiffening for convergence improvement is contraindicated by some conditions such as the substantial use of nodalpling or nodal constraint equations... see the ANSYS manuals on this. Note that SSTIF is NOT the same thing as the command PSTRES.

econd thing that helps many nonlinear solutions (both Large Displacement and plastic) to converge when substeps are being used is to activate the Predictor (PRED) in the Solve module. (This may be more of a hindrance than a help when gap and other nonlinear elements will be changing status frequently.)

ere are other settings that can be tried when attempts at convergence are not working. I usually stick to letting the program decide how to use Newton-Raphson iteration and adaptive descent in the Solve module. Under the Nonlinear settings of t he GUI, the user can modify the Convergence Criteria. I often use only convergence on forces (not moments) when analyzing shells if I am not inputting any moments directly. I usually reduce t he number of Equilibriumations to 15 when doing shell models, preferring to use smaller substeps instead. However, in a model with gap or contact el ements it may be desirable t o have a much larger number of Equilibrium Iterations. I rarely try L ine Search.

king a good choice of time substep sizes is critically important in getting models to converge. If shell models of flat plates subjected to pressure or perpendicular forces are included in the analysis, the shell will at first act as a flat plate in bending. Once the shell has curved, by movement as small as half its thickness, the shell will start to carry the applied load with membrane forces. In a model of this type, starting with very small substeps (e.g. 1/100 of the full load)y be needed to achieve convergence. I would start with a very small first substep, but al low the largest substep to be as large a fraction as 1/4 of the applied load. If there are no perpendicular loads but the loading is causing Large Displacement, or if buckling is to be considered, it is likely that small timeste ps will be needed toward the end of the force application ramp. Where there is no pressure or perpendicular force on flat shells, I would start with a substep such as0 or 1/4 of the applied load, but al low a minimum substep as small a s 1/100 of the full load. If these approaches will not work, it is likely that convergence control commands in addition to time substep size will need consideration.

he structure is buckling or undergoing plastic failure, or "simply will not converge" it may help to use the Arc-Length method. As I have noted elsewhere, I don't use the default Arc-Length settings. I usually start with a number of substeps (NSUBST), and don't let the Arc-Length solver increase the size of a step beyond my maximum substep size. I let the Arc-Length solver use a minimum step size that is 1/10 or 1/100 of my substep size. I let the Arc-Length solvera maximum step size multiplier of one. The Arc-Length method can follow a rising and falling force-displacement relationship. I find PlotCtrls/Animate/Dynamic_Results to be useful in reviewing the behavior during an Arc-Length analysis, and other nonlinear analyses. I prefer to save the results at every substep when doing this (Output Ctrls). When using Arc-Length analysis, it is usually desirable to set a criterion to stop an analysis (NCNV). I usually use

ximum displacement as the criterion for shell work.

member to ramp up your loads, permit automatic time stepping, and in the NSUBST command, allow the program to bisection by setting the maximum number of substeps greater than the minimum number of substeps.

ou are having trouble with convergence, save the results at intermediate substeps so you can review the stress and displacements. If you are doing combined Large Displacement and plastic deformation, and having trouble with convergence, consider a study in which you do (1) an el astic small displacement analysis as a check on element shape, loading, and constraints, (2) a Large Displacement elastic solution, and possibly (3) a plastic small displacement solution. Ifse work without significant warning messages, you should be making some progress. If gap or contact elements are being used, consider (4) softening the normal and tangential stiffness values in a preliminary analysis (KN and KS). You can also (5) try relaxing the convergence criteria on force and/or moment error. If desperate, a coarsely meshed model may improve speed enough for you to study what helps get a n answer. These preliminary studies may help you tod what settings help you to get convergence or discover modeling problems before you do more time-consuming accurate analysis. If you are trying a new technique, consider testing it on a t oy-sized problem, before applying it to a large industrial-sized problem that runs for hours or days, in order to learn the peculiarities and pitfalls of a particular time-consuming method.

ap or contact elements are t he only nonlinearities in a model, consider substructuring the linear regions of the model. This can result in a tremendous increase in solution speed. If only a sub-region of a model will behave in a nonlinear manner, it may reduce solution time to substructure the region that can be regarded as acting in a linear manner. This speedup effect or may not occur with large displacement modeling, when the substructure itself will be undergoingge displacement -- I have done only limited testing of this technique. See below for a brief discussion and for simple examples of substructuring.

24: Working with Load Step Files in ANSYS:

ad step files can be used to automate the application of a number of different load cases on a structure. A load step file contains loads on elements and nodes. It does NOT contain loads on geometric entities. Consequently, a load step file can be generated after all loads from geometric entities have been transferred to a model. After all loading on geometric entities has been deleted, the load step file can be read back in, recovering all applied loads. Alternatively,sider the "LSCLEAR,SOLID" command. These loads can then be scaled.

e user needs to be careful when manipulating load step files. The load step files may contain the KUSE instruction telling ANSYS to re-use the TRI file if the constraints have not changed. If the user deletes a load step file, changes the order of their execution, or manually modifies their contents, invalid analysis might result.

he model is re-numbered after load step files are generated, the node and element numbers in the load step file will no longer be synchronized with the model, and will be invalid. A way around this is mentioned elsewhere in these notes (See Tip 21).

e reader should take note of the ANSYS user guides comments on the LSCLEAR command. This deletes all loads and resets all load step options to their defaults. This can "clean up" the load step data before using LSREAD to read a load step file for modification. What this implies is that the l oad step execution process does NOT execute an LSCLEAR command when a load step file is read in. If it did, then ANSYS would have to implement substantial checking towhether a TRI file was safe to re-use, under the frontal solver (TRI file re-use saves considerable time). Load step implementation can cause havoc when the user employs load step files in a manner for which the method was not designed. It may help t o read the contents of the LSSOLVE.MAC macro in predicting what will happen, and to see what LSSOLVE does to avoid trouble. The LSSOLVE.MAC macro at ANSYS 5.3 includes some undocumented commandsuding DMARK, FMARD, SMARK, BMARK, and a *GET command that retrieves the error number in the /SOLU process. It al so uses an "LSCLEAR,SOLID" command that removes loads on geometric entities before reading in load step files. It selects a ll DOF labels, sets xCUM labels t o "replace", and does a few other things. I do not consider the manuals to pursue this t opic adequately -- a user ought to read the macro.

e ANSYS manual comments on the LSREAD command. The command does NOT clear ALL current loads on the model when it reads in a new load step file (it does clear some... read the manual).

en using load step files: If loads on nodes and elements are set with BF and BFE commands (for example applying temperatures for a thermal deformation stress analysis), then if you set up a subsequent load step, if these te mperatures are to be returned to ambient it may be necessary to use the BF and BFE command to set the nodes and elements to the reference temperature (by default 0) rather than j ust deleting the loads using BFDELE and BFEDELE and usingUNIF to input the uniform temperature. It may help to use c ommands such as "nsel,s,bf,temp,-999,99999" and "esel,s,bfe,temp,-999,99999" to select all of the nodes or elements to which temperatures have been applied, if you are going to change them. Be very careful with the BFE command. If you set the value of the temperature at, for example, four locations on an element with BFE, and in a later load step set the value at only two locations within an element, theperature at the other two locations will still be "hanging around" at the previous value. It is very easy to make this mistake when running a series of load ste p files. (Another thing I found out the hard way, in a model where both piping creation commands and beam elements were used.)

he user is deleting displacement constraints using DDELE, and then writing an additional load step file, the old constraint may still be present when the series of load step files is read i n under LSREAD; check for this in your results. Be careful with t his. It may compromise the use of load step files, or require some intervention like writing an input file that calls load step files in using LSREAD, implementing fix-up commands as needed -- be ca reful that a TRI file isre-used because a load step file contains "KUSE,1" when your changes to constraints mean that a new TRI file should be generated. Statements in the LSSOLVE.MAC macro can provide guidance on using LSREAD effectively. You may need to look inside the load step files with a text editor. Be warned that changing the contents of load step files with a text editor can be tricky because of unintended side-effects.

general the user will have to be careful that the "residue" from the loads and displacements from one load step do not appear inappropriately in later load steps. This i s true when generating the load step files in the first place, and may apply when reading in load step files with LSREAD. As noted, LSSOLVE.MAC uses cleanup statements.

e user will have to be careful to change loads between load steps in a manner consistent with getting smooth ramping of loads and displacements, for t hose cases when this is desired, either for transient analysis, or for good nonlinear analysis convergence, or when intermediate results are desired at in-between loads.

fore reading in load step files to solve with LSREAD, ensure that loads on geometric entities and elements and nodes have been deleted, unless you are keeping them intentionally (as noted, loads on geometric entities overwrite loads on elements and nodes). As noted, LSSOLVE.MAC in ANSYS 5.3 contains the command "LSCLEAR,SOLID" to remove the solid model loads on the model before proceeding.

arge Displacement analysis is going to be used in analyses run by load step fil es, the NLGEOM flag must be set in the first load step file. There will be no NLGEOM command generated in subsequent load step files. Because ANSYS does not permit the kind of analysis t o be changed when applying a series of load steps, e rror messages will be result if t he user changes the value of NLGEOM in the middle of a set of load step files.

25: Plotting Shell Stresses -- Surface, Mid-Plane Stress, Load Paths, ESYS and RSYS:

he ANSYS database, shell stresses (and strains) for t he basic shell elements (63, 43, 143, 181, and 93) are reported at the top and bottom surfaces of the shell element. The user can has four options in ANSYS 5.3 for plotting shell stresses (and strains). Three of them are selected with the commands: "SHELL,TOP" , "SHELL,MID" or "SHELL,BOT". These will cause plotting of shell stressesd strains) to be based on the values at the top surface, mid-plane, or bottom surface of each shell element. This is a bit misleading. The mid-plane stress is based on the average of the stresses at the top and bottom ( this may not be correct, at least for some elements, considering Section 2.3.4 of the Theory manual, which refers to stress on the mid-plane of a shell element separately from theand bottom, and forms the force per linear unit from a weighted average of top surface, mid-plane, and bottom surface stress -- what's going on here? ). What constitutes the top and bottom of a shell element depends on the element's orientation when it was defined (see elsewhere in these pages) . It is possible to have adjacent elements, one with a "top" surface pointing upward, and its

ghbour with the "top" surface pointing downward. In complex structures it happens all the time. If nodal averaged plots are done, for example with "PLNSOL,S,EQV", when either top surface or bottom surface plotting is chosen, then with such adjacent elements, the plotted top surface and bottom surface results will get blended, causing a misleading mess to be displayed. (See Tip 19 formmands that can re-orient shell elements.)

re insight into the flow of stress in a model can be gained by plotting t he stress vectors, using the "PLVECT,S" command. With shells, these vectors will be plotted for the mid-plane principle stress components. At times you will want to use vector graphics with no hidden surface removal, to give the best view of these vectors. If there is local compression, the vectors point inward. Thesetors can give insight into load paths in a structure.

ere there are intersections of planes of shell elements, e.g. corners or "Tee" intersections, or where elements of differing thickness meet, the averaging of node stresses can render local stress plot information meaningless at the intersection. This is true of both surface and mid-plane stress plots. This is one way in which excessive stresses will be unintentionally missed.

y time that nodal averaged plotting is done, it is possible for the averaging to "wash out" local stresses that may be important, yet it is common to do nodal averaged plots because of their much cleaner appearance (I do t hem myself). The fourth option in plotting shell stresses is to switch on the ANSYS Powergraphics feature. This causes shell results to be displayed, even averaged, for the visible surface. Options activated with the AVRES and /EFACET commandsrefine the way the results are plotted under Powergraphics (look them up). Powergraphics has the options to discontinue the averaging of stress contours where there are certain discontinuities in the material or geometry in t he model. I'm going into this detail, because a high stress that is washed out by nodal averaging could be a stress that c auses serious fatigue or other damage, such as cracking, or a weld being torn apart.

e only shortcoming is that Powergraphics will not work with mid-plane stress. The user has few options here. Sometimes it is important to select only regions of a model when doing nodal averaged mid-plane stress plots (using "SHELL,MID", without Powergraphics) so that the averaging does not wash anything out. A mid-plane stress plot without Powergraphics can be done for element stresses, using a command like "PLESOL,S,EQV". This will look messy, but att it doesn't hide an extreme stress. An alternative I used is discussed elsewhere in these pages: I wrote a macro to get the mid-plane averaged stress (all components) at every node of every element (a given node has different results with reference to each of the elements to which it is attached, so a given node will be looked up as many times as the number of elements to which it is attached), and transfer it to the top and bottom surfaces, so that Powergraphics wouldt mid-plane averaged stress neatly, with discontinuities. CAUTION: This ruins the results database. The macro is extremely slow t o run. The method (under Powergraphics) does, however, give far better looking plots than using t he "PLESOL,S,EQV" command to plot mid-plane element stresses without nodal averaging (without Powergraphics).

AD PATHS: The macro I mention above could be modified to multiply the mid-plane averaged stress components by the local shell element thickness at each node. The resulting values would yield a contour plot of force per linear i nch (or other dimensional unit) "averaged" at the mid-plane of the shell -- this could help to make load paths visible in a complex shell structure. "PLVECT,S" plots that would now show arrows corresponding to the load-per-unit-lengththe mid-plane and show the principal directions in which it points, helping to illustrate the load paths. This macro would also ruin the database for any other use. Before plotting "load-per-unit-length" data, the user needs to decide how to orient the results data coordinate systems with RSYS for information such as Sx or Sy that contains direction information (stress and strain with EQV does not contain direction information).

te: The Output Data section on Shell63, Shell43, and Shell93 includes In-plane element X, Y, and XY forces called TX, TY, and TXY. Consequently, shell "force per unit length" data can be obtained directly in an Element Table very quickly, though with a resolution of one value per element. (For Shell63, 43, and 93, use SMISC setting 1, 2, or 3 when generating the element table data.) The Theory Manual uses the term In-plane forces per unit length while thements manual refers to just forces as above -- a simple test I ran shows the data to be force per unit length. The elements manual ought to clarify this. The Element Table data can be contour plotted, but there are no principal stress style vector plots of table data. (Clarification: PLVECT can plot vector arrows based on 3 ETABLE columns, but not the double-headed arrows for an ETABLE as in a principal stress vector plot.) The El ements manual shows the TX, TY,

TXY values not being available under "Miscellaneous Element Output" at every node, only at the centroid. The Elements manual does not explicitly show that S,EQV or S,INT stress information can be extracted at the mid-plane. Their value is extracted with the component name method. Brief experimentation shows that if the command "SHELL,MID" is followed by "ETABLE,SEQVMID,S,EQV" that the column called SEQVMID will contain an average SEQVue for the mid-plane. If "SHELL,TOP" or "SHELL,BOT" is called, the ETABLE value of SEQV will change if the update command "ETABLE,REFL" is executed. Warning: When plotting ETABLE shell element element table data with PLETAB the plot information legend will read TOP, MID, or BOT according to the current setting of the SHELL command. This bit of information DOES NOT reflect the SHELL surface setting conditions in e ffect when theABLE data was stored, and could be misleading. For this reason, the label used for the column should indicate the shell layer setting in use when the element table data was loaded, as with "SEQVMID" above. Doing an element table update with ETABLE,REFL will re-fill columns with results data. A change of the SHELL layer setting can change stress results that are loaded i n an update. Consequently, loading shell element data must be handled very carefully iner that the layer choice is controlled. Element table data from the CALC module (adding columns etc.) is NOT updated and has to be explicitly re-calculated.

TE Also: The direction of the element table load-per-unit-length TX, TY, and TXY is as taken from the el ement in Element Coordinates. Unlike SX or SY, the values of TX, TY, and TXY appear to be insensitive to the RSYS setting. The Element Coordinate System will vary orientation from element to element, particularly under free meshing, and affects t he usefulness of TX, TY, and TXY data. The element table data can be processed by the user to yield a newe column containing the "load-per-unit-length intensity" in the sense of a Mohr's circle, giving rapid if somewhat coarse plots of load path information along the shell mid-plane. The plots will usually be more informative without nodal averaging. Section 2.3.4 of the ANSYS Theory manual discusses Forces and Moments per unit length on shell elements -- the suggestion is that internally, at least for some shell elements, the mid-plane stress is NOT simply therage of the top and bottom stresses. The way around the problem of el ement coordinate systems being arbitrarily oriented is to define l ocal coordinate systems before meshing areas (or otherwise generating shell elements) and use ESYS to get all shell elements oriented with the local coordinate systems. ESYS assigned to elements can be modified after the fact but before SOLVE, by using the EMODIF command in /PREP7. It may be desirable to have a localrdinate system aligned with each flat area to be meshed with shell ele ments so that all shell element coordinate systems can be al igned in the plane of the area -- a time consuming process unless a macro is used. Curved surfaces would be difficult.

e problem of orienting coordinate systems in the plotting of results is illustrated by the images below. The first shows 3 elements that were created during free meshing. The elements are plotted using vector graphics, with the element coordinate systems shown. Each element has its coordinate system oriented differently. The image below it lists the elements and their node numbers. Look at the sequence of node numbers for the three elements to see why the elementrdinate systems point in such different directions.

e next two images show a plot of TX done from an element table. The element table was filled by the TX values for the elements (this is the load-per-unit-length in the element coordinate system X direction). The values differ so much from element to element because of the difference in the ele ment coordinate systems. The plot consequently tells us too li ttle. The following element plot of Sx shows the stress in the X direction. The results are shown in the globalrdinate system.

e final images in this section show a group of Shell63 elements that have had their element coordinate systems aligned with local coordinate systems at the time of the creation of the elements, by the use of the ESYS command. This will permit element table results TX, TY, and TXY to be aligned in a known manner. This also permits Sx, Sy, and Sxy to be aligned in the plane of the elements creation if RSYS,SOLU is active when plotting stress results. Knowlege ofalignment of the loads and stresses can make plots more useful in understanding load paths, reduce the total number of plots required in model assessment, and help facilitate an evaluation of loading on welds. The first plot with vector graphics shows the elements with their ele ment coordinate systems. Note that they are al igned. There are two local coordinate systems at work in this example -- they are numbered 11 and 12 and their symbols are plotted. Elementse been created aligned with number 11 in one plane, and aligned with number 12 in the other plane of e lements. A line pressure has been applied in the global -Y direction. The second plot with raster graphics is of Sx at t he shell mid-plane. Because RSYS,SOLU was active when the Sx plot was generated, there are Sx values shown in all elements. If RSYS,0 were active when the Sx plot was done, the plane of elements that is perpendicular to the global X axis wouldw zero stress in the X direction i n this example.

ere is an alternative to using ESYS and RSYS,SOLU to align element coordinate systems for the purposes of stress plots like Sx, Sy, and Sxy. During postprocessing in /POST1, a local coordinate system can be ali gned with the plane of shell elements of interest, and RSYS set to t hat local coordinate system, before plotting Sx, Sy, or Sxy. However, this would do nothing for TX, TY, and TXY which depend on the element coordinate system and are generated in anment Table.

ave the topic of whether t o plot surface or mid-plane shell stresses to the reader to determine. Too much is industry or application domain specific. Hint: Check mid-plane plus both shell surface stresses. Surface stresses and strains can cause local bending, cracking, breaking of protective coatings, fatigue, and imply possible overload or prying of welds and fasteners, and can highlight other troubles.

26: Nodal Coupling (CP) versus Rigid Region (CERIG):

ve seen analysts mistakenly use nodal coupling where rigid region constraint equations should have been employed. (The nodes concerned were not at the same location in space.) Rigid region constraint locks together a select ed set of nodes so that they translate AND rotate in space as if they were locked together by an infinitely stiff structure. Nodal coupling locks together selected degrees of freedom (translation and/or rotation) individually, so that the same degreereedom value will result for the nodes in the coupled set. Nodal coupling will not combine the rotations and translations that are necessary to imply rotation as a rigid body in space.

te that rigid region constraint may not be appropriate for Large Displacement, when the displacement rotations are significant (sin(theta) differing from theta, etc.). This i s because ANSYS uses a linear approximation to the rigid body rotation matrix. A rigid region grouping can be implied by tying nodes together with extremely stiff beam elements (zero-mass beam elements a few orders of magnitude stiffer than the structure to which they are attached.) The beamments should have the advantage that they work under Large Displacement. The beam elements should not be too stiff, or ill-conditioned matrices could result. If the beams are of very widely varying lengths, then some may be too stiff, others too flexible -- remember that flexibility is proportional to length cubed.

n a model in which about one thousand beam elements were used to position gap elements. These beam elements would ideally have been infinitely stiff. I needed elements, instead of nodal coupling or constraint equations, because of thermal expansion considerations. The beam elements were widely varying in length. This created solver trouble, until I wrote a macro that assigned each beam element a unique REAL value, which set values for each BEAM4's Ixx,, Izz, and Area as a function of the element's length. I found it sufficient to set their stiffness a couple of orders of magnitude stiffer that contact stiffness for the gap elements.

ning on the symbols for nodal coupling and for nodal constraint equations is very helpful in reviewing the correctness of a model.

27: Vibration Modes with Pre-stress:

culation of natural frequencies and modes of vibration CAN be done with pre-stressing of the structure under ANSYS. There is a "PRESTRESS" flag to set under modal analysis. This is available in the dialog box for Modal Analysis Options. First, do a static analysis with the prestress flag set. Exit Solution (click Finish or enter "/fini"). Re-enter Solution, and do a modal analysis with the prestress flag set again. This doesnot seem to work when the stress run is doneh Large Displacement activated.

ave the question of how a performer plays music with a hand saw and a violin bow as an "exercise for the reader" :-)

28: Creating New Elements by Copying or Reflecting Existing Structure:





order to create new elements by reflecti ng or copying existing elements, there are a few things to do. First, select the elements to be copied and get their nodes with NSLE. Copy or reflect the nodes, noting the nodal number offset that will be used -- write it down. Copy or reflect the elements, using the nodal offset number that you wrote down. ANSYS should default to a nodal offset number equal to your highest numbered node. If you make it small er, you run thek of changing the location of nodes that already exist, resulting in a lovely mess. If you are running something like ANSYS/ED you may want to compress your node numbers first, for if a node number results that exceeds the ANSYS/ED limit, the program will terminate immediately (the more recent ANSYS revisions may give a non-fatal warning message and quit some time later if you don't clean up). You could compress the node numbers, and then make the offsetmber equal one plus the difference between the maximum node number of the whole model and the lowest node number of those nodes to be copied or reflected. You can find these node numbers with *GET commands. (Remember that compressing node or element numbers will destroy synchronization with Load Step files.)

e same nodal offset number will need to be used if nodal coupling is to be copied as well. In order to copy nodal coupling, use "Generate Coupled DOF Sets with same DOF" for which you will need the same nodal offset number. Do a replot to see the newly created nodal coupling. Caution: Be sure that if nodes were deleted earlier, that nodal coupling equations that i n the past included those deleted nodes were a lso deleted. If you forget, you may get a pretty mess.

member that if there are nodes on the plane of reflection, new nodes will overlay them. Merge commands may be wanted for the nodes on the reflection plane. Now the tricky part: elements lying in the reflect ion plane (shell elements will do this) get generated with the node order reversed, because of the mirror imaging. They Will Not Merge with the element from which they were reflected. They may have to be deleted, depending on what you are trying toomplish. Alternatively, do not select elements that lie in the plane of reflection when reflecting the structure. You still need to reflect the nodes on the plane of reflection, in order to reflect the elements that will join them to the remainder of t he reflected structure, so the nodal merge will still be needed.

29: Adding to a Model Comprised of Elements and Nodes Only:

may happen that a model that consists of nodes and elements only has to have a section replaced, or requires the addition of more structure. The way to attach new geometry onto existing nodes and elements is to: (1) Place keypoints on the nodes onto which new geometry is to be built (i.e. grafted). (2) Join these keypoints with lines. (3) Set mesh density along these lines to only one element. (4) Build new geometry outward from these keypoints and lines. This getsssy if you are building solids. (5) Mesh the new geometry. (6) Select the nodes (new and old) along the interface between the old nodes and the nodes of the new geometry. (7) Merge ONLY these nodes along the interface using the NUMMRG,NODE command. Alternatively (much more work unless a macro is written or the CPINTF command is used correctly), fully couple the PAIRS of nodes with the CP command. In the event of elements with mid-side nodes,s will have to be created curved so that a si ngle line spans three keypoints placed on the three nodes along the edge of an element. It is probably advisable to connect elements with mid-side nodes to other elements with mid-side nodes.

s attaches the new geometry and mesh to the old elements and nodes. Be sure to double check that the merging has been done correctly and according to your intentions -- I have found this to be a surprisingly error-prone operation.

30: Zero Mass Beam Elements Form Rigid Region:

analyst could use very stiff beam elements (a few orders of magnitude stiffer than the surrounding structure) in order imply a rigid region grouping of nodes, which works under Large Displacement (a CERIG group does not work with large displacement). This is an old FEA trick -- it is not perfect. A separate material should be created for these beams, and be given z ero mass (set the material density to zero) so that no gravitational or other inertial load acts on theterial. A thermal expansion coefficient should be input if appropriate -- it would usually be identical to the coefficient value for the structure that it approximates.

rote a macro to create a rigid region using beam elements. It i s called after the set of nodes to be connected is selected. The lowest numbered of the set of nodes is attached to each of the other nodes in the set by a beam element. The beam element to use has to be set up in advance, and the appropriate MAT, REAL, and TYPE set by the user. A macro like this is very fast to run. Caution: Such a macro would become complex if it checked for duplicate nodes at the firstde location (ANSYS can't use zero length beams), and checked for widely varying beam lengths. This is not a guaranteed method.

31: Turn off Symbols When Changing a Model after Solution:

ou have run SOLVE, the results database will be full of data. If you then change a model, and create anything that plots a symbol, all symbols become active, and plots become extremely slow. Turn off symbols with /PBC,ALL,,0 to speed things up. I put this command in the Toolbox for convenience. I have found that plotting can become slow with very large models when loads have been applied, and even when applied and deleted. Presumably ANSYS is checkingee if any symbols should be shown. The plotting speeded up considerably when symbols were turned off with "/PBC,ALL,,0" even though there were, in fact, no symbols to be plotted.

32: Are the "Free-Free" Vibration Modes Relevant?:

mple supports on a structure may be appropriate for static analysis and gravity loading, since the structure will "sink" until the simple support reacts enough to withstand the applied load. If a modal vibration is excited, small amplitude vibrations may result in very li ttle response from the support, and vibration similar to a structure that is free in space may result (this is obviously very problem dependent). If so, it may be desirable to run a modal vibration analysis withconstraints. More than six modes must be requested, since the first 6 represent the free translation and rotation, and give Zero eigenvalues. A better approach would be to characterize the flexibility of the constraint points. With some structures, you may get a few surprises, as torsional and other vibration modes appear.

33: Selecting a CAD or FEA System -- Cover Yourself

common to evaluate a few CAD or FEA packages when trying to make the right choice for a purchase. Watch out for this stunt: (I've seen it done, and been threatened with it once (I laughed at her).) A losing vendor writes a letter to your boss, or even to the head of your company, claiming that the engineers are incompetent (stupid, uninformed, can't spell, and so on) and making a huge mistake. If the boss is not an engineer and cannot understand the i ssues, thisld get awkward. (Certain Dilbert cartoons come to mind.) Warn your boss(es) in advance that a few vendors pull this move and that you and your group will evaluate the products in a thorough manner. Write down some criteria and your assessments. Also, be careful that you cannot be accused of leaking information unfairly from one vendor to another -- date your correspondence carefully, and work through your purchasing department if that is appropriate at your

m. Some sales-types are very greedy for their commissions, and petulant when they lose. (Names will not be mentioned, to protect the guilty. If you've been around the block a couple of times, perhaps you can make a few guesses.)

e ANSYS vendor I've dealt with has been very professional.)

34: Creating Lines Perpendicular to, or at Angle to Existing Lines

en creating structures in the /PREP7 portion of ANSYS, I find that the commands that create lines that are perpendicular to existing lines, or at an angle to existing lines, are extremely useful. Look at the commands LANG, LTAN, L2ANG, as well as the others. These commands break lines where new lines intersect, even though the original lines are already attached to areas. Since I often model shells that are to act as if they are weldedether, I need the lines to be shared where areas contact each other. These commands give the connectivity I need.

e command that meets another line at an angle may do better if it is entered manually, with the first guess of the contact point set at 0.0, 0.5, or 1.0, depending on your intention. This often succeeds when the interface command fails.

35: Use the /UI command in Your ANSYS Toolbar to Bring up GUI Dialog Boxes

ke a look at the /UI command in ANSYS. You can use it in your Toolbar to activate certain GUI dialog boxes with one-click simplicit y, instead of finding your way though the menu system. I sometimes get odd results from the Hard Copy command when I do this -- I have no i dea why.

36: Reaction Force, Nodal Force, and Load Paths

orked on a model subject to aerodynamic pressure and gravity load. We needed to know the load that the structure would apply to its foundations. Printing the Reaction Force would give this value, however the +/- sign is in the direction of the force that the constrained node (or nodes) applies TO the structure. If nodes are selected with the three commands NSEL,S,D,UX $ NSEL,A,D,UY $ NSEL,A,D,UZ the Nodal Force at the constrained nodes can be printed. Thishe force with which the nodes press on the supports. (NOTE: You may need to include nodes where there are constraints on rotation, depending on what you are modeling.)

ARNING: A number of things can go wrong with this approach.

. If you ask for nodal forces without limiting the node selection to nodes where there are constraints, you will get nodal forces wherever forces and pressures have been applied to your structure. (For the curious, printing nodal forces when only pressure has been applied to shell and high order elements will illustrate t hat FEA software inputs a complex set of forces and moments because of how the elements are derived from first principles. What is being printed isthe force with which the nodes react t o the forces input from outside -- if a moment is input, a nodal "force" moment is output in reaction.)

. If an input force has been applied to a constrained node, the nodal force and the reaction force magnitudes will differ. When I tested this, the reaction force that ANSYS listed was modified by the presence of a force applied directly to a constrained node, whereas the nodal force (that is based only on element deformation) was not affected.

. IMPORTANT: All the elements to which the selected node is attached must be select ed in order to get the total force with which the node pushes on the outside world (use ESLN after selecting the nodes). The generation of Nodal Force (and Reaction Force, if I remember correctly) is determined from the deformation and stiffness of at tached elements. If elements attached to a node of interest are not selected, then the contribution of those elements to the force atthe node is not included and will be missing.

. Caution: If you have used a rigid region with the node of interest, the lack of el ement deformation means that you will NOT get t he Nodal Force or Reaction correctly -- you may need to work from the set of nodes where the rigid region attaches to the flexible part of t he structure. I'm not sure what kind of effects nodal coupling would have.

ere are various other uses to which you can put Nodal Force. You can plot the Nodal Force vectors along with your model (see the /PBC command), after SOLVE, giving visual cues during your review. You can use NODAL FORCE to find out about the load being carried in certain Load Paths:

Determine where to position a "cut" in the model. Locate it where you want to determine the force carried ac ross the cut. The "cut" should follow a path along the edge of a set of adjoining elements. Select all the elements on ONE side of t he "cut". Select the nodes on the "cut" side of those elements. Printing the Nodal Force (forces only) will tell you about the forces that your selected elements apply to those nodes. The sum that is printed tells you the total force carried across the "cut" in the X, Y, Z directions, based on t he selected elements. Caution: Getting the moment across the cut is not so easy, because moment is determined with respect to an axis. You would have to do extra work to pursue moment across a cut, determining your "neutral" a xis, and using other commands. See, for example, ANSYS manuals information on the SPOINT command.

te my earlier comment Tip 25 on making load paths visible in shell models. For further information, read the ANSYS manuals on the FSUM and NFORCE commands.

37: Inputting Temperatures with BF, BFE, and TUNIF in Structural Analysis

discussed by ANSYS in Chapter 2.6 of the Elements Manual, Body Loads (temperatures for structural analysis that cause thermal strains and affect temperature dependent material properties) may be input in a nodal format or an element format. " Either the nodal or the element loading format may be used for an element, with the element format taking precedence. Body Loads are designated in the "Input Summary" of each element." This means that if both BFE andare applied to an element and its nodes, and the inputs differ, the BFE setting will govern. If temperature is input on a nodal basis, the temperature input at a node will influence all the attached elements. If temperature is input on an element basis, the temperature(s) input will influence only the element to which it was applied. The commands TUNIF and BFUNIF can be used to set a ll nodes to one default temperature that differs from the reference temperature. Then,

or BFE commands can to used on specific regions of the model to put in other temperatures.

ou use piping commands to create pipe elements, and have applied temperatures, ANSYS will apply the temperatures on an element basis (to check this, generate a Load Step file and inspect its contents, or use the BFLIST and BFELIST commands). For the user applying temperatures directly, it can be a little simpler to apply temperatures on a nodal basis with BF, since the nodes can be sel ected by location. Inputting temperatures on an element basis with BFEmits control of things such as temperature differences between the inside and outside of pipe elements, or between the top and bottom of beam elements. The element l isting in the Elements Manual should be consulted before applying temperatures with BFE. As I discussed elsewhere, if you change temperatures that were previously set with BFE, the temperatures have to be changed at all the locations within each element to which temperatures were applied.

herwise, the old temperatures will still be there. You may want to clean up with a BFEDELE or other cleanup command before starting. The BFDELE and BFEDELE commands only act on selected nodes and elements -- if you want to remove all temperature application, select the full model first. Be wary of what happens when you use Load Step files.

38: ANSYS Toolbar Use

e ANSYS Toolbar can be very helpful in giving "one click" ac cess to frequently used commands. Toolbar buttons can also call macros, or the function form of commands, for example Fnc_Pl_Symbols to bring up the dialog box for setting symbols. If you want to get fancy, a t oolbar button could be used to activate an alternative toolbar.

he toolbar shown here, a variety of buttons have been enabled. Some of the captions are a lit tle cryptic; this is because the captions are limited to only 8 characters. The command that gets executed cannot include the $ sign. Consequently, only one command can be executed, however, a macro can be called in order to perform a complex set of instructions. The toolbar editing is brought up from the menu item "MenuCtrls". In the examplelbar shown here, the buttons are not in a highly logical order. In order to modify the button sequence, save the toolbar (I suggest the unimaginative file name "toolbar") and re-order the lines in that file with a text editor. Keep the eventual sizing of your toolbar in mind. The example here is sized for six rows deep, and seven columns wide. Use the "Save Menu Layout" menu selection to save the l ayout of all of your ANSYS windows includingtoolbar shape. (This setting is destroyed if you modify the "GUI configuration" under your ANSYS Interactive startup dialog box.) When you are happy with the layout of your toolbar, you can append the toolbar file's contents to the end of the "Start.ans" file l ocated in the ANSYS "DOCU" subdirectory.

39: ANSYS Piping Elements

e use of ANSYS piping elements, Pipe16 and Pipe18, can simplify the work required to create models of piping systems that will satisfy c ertain code requirements. Piping commands can be used in /PREP7 to directly create models of piping. In using piping creation commands, a user works out the intersection points of t he runs of piping as if there are sharp angle bends. Each run of pipe is entered as dx, dy, dz, creating Pipe16 elements, andn a radius of curvature at the previous intersection can be applied, creating Pipe18 elements. The Pipe18 elements are taken out of the two Pipe16 ele ments that met at the last corner intersection. If these two Pipe16 elements are too small t o encompass the Pipe18 bend elements, difficulties will result. If the user is defining U-bends, it is easy to have zero-length Pipe16 elements generated. My approach to this is to inspect the model for zero-gth Pipe16 elements, and delete them, after I make sure that all pipe nodes are merged. I use a macro to inspect the model and do the deleti ons. Checks are included in the macro, because Pipe18 elements always return a zero length. I have also seen users do a U-bend with a small extra space so that a very small Pipe16 element will remain between the two 90 degree bends that make up the 180 degree U-bend, avoiding a zero-length elementblem.

list or plot useful stress information from the piping model usually requires putting selected results data into element data tables, and the use of appropriate PLLS commands. Fortunately, ANSYS includes many output possibilities for the two piping element types, so typical piping code requirements can be met. See the element manual for these elements for information on the available output data.

obvious reasons, I leave proper use of design codes within piping analysis as an "exercise for the reader." :-)

ing creation in ANSYS includes the possibility of added mass due t o fluid in the pipes, and from insulation added to the piping. The insulation addition is simple -- the user can input thickness and density. This le ts the added mass presence of heat exchanger fins be easily faked by inputting the product of fin_thickness x fins_per_inch x fin_material_density as the "insulation" density, and fin height as the "insulation" thickness. (Substitute the a ppropriate dimensionfins_per_inch, etc. for your system of units.)

e deflection behavior of pipe elements is based on ANSYS beam elements. If accurate vibration behavior is to be modeled, at least several pipe elements will be needed between supports. If accurate gravity-induced deflections and stress are wanted, better results will come from the use of a consistent mass matrix, i f element density between supports is low.

veloping an understanding of the function of the ANSYS element creation commands (BRANCH, RUN, BEND, and so on) will require creating some elements with material and dimensional information, then reviewing what element TYPE and REAL data has been created in the model database. Model review is e nhanced by plotting the elements with the /ESHAPE option active.

ere piping is connected with sliding supports to the outside world, the use of gap elements may be needed if sliding friction is to be included in the model. ANSYS does not differentiate between static friction and sliding friction coefficients, so a reasonable and conservative value for coefficient of friction (as well as contact stiffness of the gap element) will have to be determined by the analyst. If there are thermal expansions in the piping, stresses predicted by thedel will usually be reduced if the gaps in the support structure are included in the model (depending on the nature of the structure) rather than having "tight" fit s at the sliding connections.

40: Graphical Output from ANSYS

ou start up ANSYS under Windows NT with "win32" selected for graphics, the stress plots will be shaded. If you select "win32c" for the graphics, the stress plots will not be shaded, and will usually look better when plotted to paper, especially when plotted from ANSYS with HardCopy to ink jet printers. They can be selected with the commands /SHOW,WIN32 and /SHOW,WIN32C when using the GUI.

tting to the screen window with Z-buffering as the hidden surface control can give very satisfactory and often quicker results. Hard copies of these Z-buffer plots, however, will look "pixelated", being limited to a coarse resolution. Better looking hard copies to paper will usually result if the screen is set to "Precise Hidden" or even to Centroidal hidden surface control. This is usually true of plots sent to a file, for subsequent processing with the ANSYS DISPLAYgram.

ts can be redirected to files by using the /SHOW command. This permits the DISPLAY program to do various things with the results, including the generation of animations. Under Windows NT, an animation can be generated as an AVI file.

ccasionally find it helpful to generate an animation file based on a si ngle stress plot of a load step, in which I spin the model about the screen X or Y axis. You can use the /ANGLE command and the /REPLOT command to accomplish this. A simple macro does /REPLOT calls with the model set at a series of angles from 0 to 360 degrees. You can even execute this command on one line using the "$" symbol to separate the commands. The command "*DO,III,0,355,5ANGLE,ALL,III,YS,0$/REPLOT$*ENDDO" will achieve this for you. The scaling of the display should NOT be set with / ZOOM,OFF or else the image will "move i n and out" in order to fill the screen as the view is rotated -- set the zoom level manually with picking; you may want to move out so that the model fits in all views. You may need to experiment. Node plots without symbols are a quick way to assess the behavior while testing. If the plots have been re-ected to a file when t his command is executed, the plots in the file can be animated by the ANSYS DISPLAY program.

the ANSYS 5.3 level, and presumably above, you can do a /SHOW,VRML plot to get a 3-D VRML file produced of a 3-D model plot. This could be a stress contour plot of a 3-D model. With the right options activated for a good VRML viewer plugged into a Web browser, the stresses on the 3-D model can be reviewed at any viewing angle with the positioning control a VRML viewer. This ought to be particularly interesting on a computer with a fast 3-D graphicselerator.

ere are utilities that can convert a Postscript output file from the ANSYS DISPLAY program into a bitmap image file. A free conversion program is Ghostscript, once you figure out how to use i t. The user should get a front end for the Ghostscript program, for ease of use.

der Windows NT, the Alt/PrintScreen key combination will copy a window to the Clipboard. This can be used to capture an ANSYS graphics window for pasting into a word processor document, or into an image processing program for conversion to a GIF or other bitmap file. GIF files can be used in WEB pages to show the results of ANSYS work. I recommend GIF over JPEG files for images from ANSYS, because GIF files precisely reproduce 256, 16, and 2or images (you have to reduce the colors to 256 or fewer levels in the image processing program, or accept the default color reduction used when the GIF file is generated.) Before capturing the Graphics window of ANSYS, set its size to your satisfaction. Bitmap image size changes in an image processing program are not satisfactory with this type of graphical output. If you want to get really fancy, generate a GIF file that contains an animation of a ANSYS model.nimated GIF files can be generated from individual images with software that you can find on the Web or purchase.)

sizing of the ANSYS graphics window under Windows NT is painful if a model has been plotted, because ANSYS wants to keep re-plotting the image as the window edge or corner is dragged. This problem goes away if you set the Windows NT Display Properties to NOT show window contents while dragging. I keep my PC permanently set this way for this reason.

p 41: Check Nodal Loads at Bolts, Rivets, Spot Welds and Links

herever connection by bolts, rivets, or spot welds has been represented by various simplifications or representations in an ANSYS model, the load on those connections should be checked, and compared with allowables. Spot weld review may require assessment of moments (especially about an axis perpendicular to the sheets that are spot welded together), as well as assessment of forces. One way to do this is to select the appropriate node(s) at the connection, selectments on "one side" of the node(s), and check nodal loads. The connection devices should not be overloaded. The hole in which a bolt or rivet is placed must not be overloaded or too near an outside edge of a sheet or plate, either. Additionally, building codes usually forbid or substantially limit "prying" loads on bolted and riveted connections. If the FEA model has good detail, including gap or contact elements, a high prying load can be demonstrated in some modelsver assume your FEA model will automatically show you all trouble spots).

milarly, links or "spars" that are loaded should be checked for stress, and be checked for buckling. Since a li nk will be represented by one element that is pin connected at the ends, and only cross section area is entered, ANSYS will not generate buckling information about the link, not even in a Large Displacement analysis. The user must do some work to compare compressive load with critical buckling load (use a good margin of safety). A user could write a macro top through all link elements, identifying the compressive stress and force, and calculating buckling information. The ANSYS Link10 element supports a tension-only and a compression-only capability. Where it is not known in advance whether all links will remain in tension, and the links are slender, this element could be used to imply that no link c an support compression for what may be a "worst case" evaluation of some models. An example would be the stays thatport the mast on a sailboat, with pre-tensioning implied with initial strain. (If the stays are woven rope or steel cable, getting a representative crossection for the link elements will require some extra work.)

ot weld representation in large structures is usually an inexact science in FEA modeling. Spot welds will be found, for example, in many automobile body structures. Plug welds are a stronger alternative, applicable to thicker steel sheets and plates. The crudest and quickest representation of spot welds is to merge coincident nodes from the two joined l ayers where nodes have been intentionally created coincident at t he spot weld. Alternatively, the nodes can be fullypled with the CP command if they are coincident. They can be joined as a rigid region with CERIG if the nodes are close but not touching as when shell elements are kept at the mid-plane position of two sheets that are spot welded together. (Remember that CERIG is valid only in small displacement analysis -- coupling with zero-mass stiff beam elements could be substituted if large displacements were needed.) The shell nodes can be joined with a beam element thatproperties that reflect the diameter of the spot weld. The roughest approximation will merge or couple just one node pair. If nodal coupling is used, rotations should be coupled as well as translations, for spot weld representation. NOTE: With shell elements, read the "drilling mode" comments in the ANSYS Elements Manual -- it may be necessary to set a KEYOPT value to transmit rotation and torque about an axis perpendicular to the shell elements when a spotd is crudely represented by single node pair coupling, merging, CERIG, or beam elements. Contact elements between the joined shells or materials may want consideration. Exactly what to do for spot weld representation is very problem, industry, and material dependent. These very approximate techniques tell us little or nothing about stress, fatigue, or fracture possibilities near or at the weld. More elaborate modeling (more nodes and elements, and special elementes) of each spot weld could give more information about local stresses, when local stresses matter. Studying the "crack" t hat is hidden between the sheet met al layers in a spot weld is an "advanced topic" -- discuss this with an expert or consultant. I doubt that you would find many spot welds used with aluminum, not only because of the difficulty of welding aluminum, but also because of the fatigue considerations -- consider how commonly aircraft use rivets anddern adhesives.

ere is a document on spot weld fatigue and FEA on the MSC/Nastran website. (There is a variety of other good reading at the site, t oo.) Take a look at the paper in PDF format by Heyes and Fermer, which, although it is MSC/Nastran related, is interesting and includes the following references:

Rupp,A., Störzel,K. and Grubisic,V. "Computer AidedDimensioning ofSpot-Welded Automotive Structures". SAE Technical Paper 950711, 1995. Smith, R.A.and Cooper, J.F. "Theoretical predictionsof the fatigue life of shear spotwelds."Fatigue ofWelded Structures, Ed.S. J. Maddox,pp.287 - 293, The Welding Institute, 1988.

British StandardsInstitution. Code ofPractice for Fatigue Design and Assessment of Steel Structures.BS 7608,1993.

Radaj,D. "Local Fatigue Strength CharacteristicValuesfor Spot Welded Joints."Engineering Fracture Mechanics, Vol.37, No. 1, pp.245 - 250, 1990.

Sheppard, S. D.and Strange, M. E. "Fatigue Life Estimation in Resistance SpotWelds: Initiation and EarlyGrowth Phase." Fatigue and Fracture ofEngineering Materials and Structures, Vol. 15, No. 6, pp. 531 - 549, 1992.

Sheppard, S. D."Estimation ofFatigue Propagation Life in Resistance SpotWelds." ASTM STP 1211,Advances in Fatigue Life Prediction Techniques, M. R.Mitchell and R. W.Landgraf, Eds.,pp. 169 - 185, ASTM Philadelphia, 1993.

Heyes,P., Dakin, J. and StJohn, C."The Assessment and Use ofLinear Static FE Stress Analyses forDurabilityCalculations." SAE Technical Paper 951101,1995.

ve never worked in aerospace, but I recently had a look inside a old helicopter that was on public display. In addition to rivets, what was either a caulking or an adhesive appeared to have been used between some ribs and the outer shell. This may prevent corrosion in the gap, and help reduce vibration and fretting or galli ng. If it is purely a soft caulking, it might be ignored in FEA, but if it functions as an adhesive, the load on the rivets is probably reduced.sumably the manufacturer has standards for this type of design.

42: Use QUERY to Check Results with Picking

POST1 the "Query Results" capability applied to nodes makes i t easy to check on results (stresses, strains, deflections, etc.) by picking nodes. To see an i mage of this in action Click to See Image and use your browser's Back button to return. For the shell element illustrated, the result will be reported for the Top, Middle, or Bottom, according to how the SHELL command was issued (the usual rules as to what constitutes the Top and Bottom of a shell element apply).ill do this even if PowerGraphics is active for the plot on t he screen. Note that the nodal st resses are based on averages if more than one element that is connected to a node is selected. You can inspect the consequence of element selection on nodal stress easily with this feature. The e lement query returns only data on energy and error estimation.

43: Loads on Geometric EntitiesOverwrite Loads on Nodes and Elements -- Easy Error to Make

"dumb move of the week" was to retrieve an old model of a beam with redundant supports, change the load on a node, and re-run the model. I then updated the el ement table results, and used PLLS to plot the result, as shown below. This is a plot of top surface bending stress, with gravity loading included. Both applied point loads and reactions are shown as colored arrows. Stress colors have been gray scaled for printing to a black and white la ser printer. Uponpection by a co-worker, he noticed that the results were the same as the results the last time the model was run, under different loading, a month before. What was wrong?

e model database file had been saved with the original loading and results. The original model had the load applied to the keypoints. I changed the load on a node. When I ran SOLVE, the load on the keypoint OVERWROTE the load on the node, and I got the old result. When I listed the applied forces with FLIST before running SOLVE, I saw my modified loads. When I listed the applied forces with FLIST after running SOLVE, I got the OLD loads on the nodes.e same principle applies to loads on lines, areas, and volumes. Presumably, it happens with applied displacements, also. Since l oads on geometric entities cannot be scaled, t here may be little reason to keep the loads on geometric entities after these loads have been transferred to nodes and elements, EXCEPT when meshing may be changed in the future. The use of components is an alternative way to select parts of the model for loading.

ggestion: The user should add a warning annotation stating that loading is on geometric entities, before archiving a model. Should ANSYS add a warning message about SOLVE transferring loads from geometric entities, which requires user acknowledgment?

otentially dangerous mistake -- watch for it!

44: Use Components for Load Input, and for Results Review

ser-written input file could be used to apply l oads to components that the user has defined. An even more convenient use for components is for reviewing stresses due to a load. The components can be called up and stresses plotted without the need to do manual selection over and over for each load case. I wrote a macro that automatically steps through all components, plotting the stresses for each component from a couple of viewpoints, for each load case. When thets were diverted to a plot fil e, the file could be used in ANSYS DISPLAY to plot stresses for all components for all load cases. Statements in the macro would put the component name and weight (based on volume only) in an annotation; the title already contained the load case name.

45: Simple Substructuring Examples-- Bottom Up and Top Down

SYS/ED is capable of only a small number of Master Degrees of Freedom (50 the last time I looked), so any use of substructuring in ANSYS/ED will have to be done with a very small number of nodes for master degree of freedom use. A 2-D element such as PLANE42 may be best for many substructure experiments with ANSYS/ED. In Large Displacement substructuring, rotational degrees of freedom are needed at the nodes, and ANSYS/ED will only handle veryall numbers of nodes -- 2-D beams may be best for l earning experiments with Large Displacement. The problem with using beams elements for learning is that review of stresses is more complex; element tables must be used to hold and display beam stress information. For an alternative, consider SHELL63 elements with very few MDOF nodes (8 nodes x 6 DOF/node = 48 DOF), in Large Displacement substructuring studies.

bstructuring has become more rare in FEA work, because of the capacity of modern computers for large models. There are still times when it is desirable, such as when gap elements or contact elements are employed in large models, or when extremely large models are in use. The user will have to employ some i nsight to select substructures in a way that minimizes the resulting number of degrees of freedom and wavefront size. Substructuring is a relatively trickycedure, particularly with multiple substeps or multiple substructures. For serious use, the ANSYS manuals on substructuring should be purchased and studied in detail.

e reader is reminded that the e lements inside a substructure are treated as linear. Any nonlinear elements grouped inside the substructure will be treated as if they were in their initial condition, without material nonlinearity. The two simple examples below do not address use of multiple substructures, multiple load cases, g-loading, vibrations, and other complications. Nonlinearity (Large Displacement) is mentioned only briefly. If you do not turn to expert help forstructure work, I recommend substantial testing of any techniques on small models before doing any real work.

rning: Read the ANSYS Elements Manual section on MATRIX50 the superelement. Note its warning that if gravity is applied during the "gen" pass when the superelement is created, and gravity is applied during the "use" pass, it will be a pplied TWICE to the superelement substructure DOUBLING the gravity load on the superelement region of the model. For this reason, gravity load would have t o be introduced "carefully". Unfortunately, a detailed desctiption ofcareful application is not included in the base ANSYS manuals. In the "Top Down" example below, I set "ACEL" for the model to ZERO in a ll three global coordinate directions during the "gen" part t hat generates the superelement. If the user has applied gravity to the model file that is read in, it will be applied during the "use" part of the analysis, and so only applied once to the superelement.This may affect the accuracy of the solution -- I have not yet done

mparison runs to test this. The example does not address centrifugal loading or other complications. Unfortunately, linear acceleration loading (e.g. gravity loading) is more accurately represented when applied as a load vector. This presents a problem when there are elements with mass that are not included in substructures. I have not yet determined whether gravity could be applied to a superelement in the GEN pass, without having a superelement mass matrixerated -- if it could be done, then the "accurate" application of gravity loading to t he superelement could be accomplished without counting gravity load twice. Using rotated superelements introduces another set of problems with the direction in which loads are applied -- read the manuals.

te that non-zero applied DOF displacements are not to be applied by a load vector, so MDOF should be applied to nodes where non-zero DOF values are to be applied during the analysis. Loads and constraints created in the GEN pass (i.e. in a load vector) cannot be changed in the "USE" pass, except by uniform scaling. Brief testing I did suggests that load ramping DOES work for load vectors -- the user should check this independently. The exception to uniformling is with respect to angular motion -- read the ANSYS tutorial and user's guide manuals on substructuring.

e substructuring examples given in Chapter 4 of the ANSYS Advanced Analysis Techniques manual leaves out the routine steps -- leave out too many, in my opinion. The user should purchase an ANSYS manual and tutorial manual on substructuring before doing serious work. (ANSYS 5.5 has added some helpful comments to its Advanced User's Guide on Substructuring.) The command EXPSOL has to be added in the expansion pass of the bottom-up example iner to get any results in the expansion results file. The SFE command is needed only if loads were applied to the superelement -- if SFE is used, it has to point to the element number of the superelement that was read in with the SE command as well as the appropriate load step number. A *GET command could find the element number of the superelement right after the SE command. The commands manual does not explain this adequately in ANSYS 5.3. Theowing examples are fairly brief. In the bottom up example, the coupling command CPINTF is used to join the superelement with the non-superelement portion of the model. The example shows the stresses in the superelement after the expansion pass completes. The results of the use pass are saved in the file "use.db" for later review by the user.

ttom Up Substructuring Example:





! Substructuring demonstration *************** ***************** *****! For information only. Use at your own risk.

fini ! finish whatever was active previously/clear ! clear the database

/title,Substructure Technique Test

/filname,gen ! filename for the generation pass

/prep7 !et,1,shell63 ! element type 1 set to SHELL63

r,1,.05 ! shell is 0.05 thickmp,ex,1,3000000 0 ! set value of E

blc4,-.5,0.5,1. 0,-1.0 ! create a rectangular arealesize,all, , ,3,1,1 ! 3 elements per line -- user can change thisamesh,1 ! mesh the rectangle

fini/solu

antype,subst ! substructure analysisseopt,gen ! generation pass

lsel,s,line,,2 ! line at right sidensll,s,1 ! select all nodes on linem,all,all ! make these nodes Master Degrees of Freedom

lsel,s,line,,4 ! line at left sidensll,s,1 ! select all nodes on line

d,all,all ! constrain nodes against all motionallsel

save ! save this part of model as gen.db for expansion pass! the save need not follow "solve"

solve ! generates the gen.sub file

fini

/clear,nostart/title,Shell elements are attached to a superelement

/filname,use ! filename for the use pass/prep7

et,1,50 ! element type 1 set to superelement MATRIX50type,1 ! set type 1se,gen ! read in the superelement matrix from generation pass

! after reading superelement, create remainder of model:et,2,shell63 ! element type 2 set to SHELL63

r,2,.05 ! shell is 0.05 thickmp,ex,2,3000000 0 ! set value of E

blc4,.5,.5,1.0, -1.0 ! create a new rectangular arealesize,all, , ,3,1,1 ! 3 elements per line -- user can change thisaatt,2,2,2 ! assign mat=2, real=2, type=2 to the unmeshed area

amesh,1 ! mesh the area -- note superelement node numbers are not usedcpintf,all ! automatically couple coincident nodes at interface

eplo

fini/soluksel,s,kp,,3 ! keypoint at upper right cornernslk ! select node at this keypoint

f,all,fy,-1 ! put a load on node at upper right cornernsel,all ! select all nodes

! SFE,1,1,SELV, ,1 ! no load applied in generation pass, this statement not neededsolve ! results go in the file use.rst

save ! save use.db to review results in the non-supereleme ntsfini/post1

/pbc,f,,1 ! show applied force symbols/pbc,cp,,1 ! show nodal coupling symbols

plnsol,s,eqv ! plot the stresses in the non-superlementsfini

/clear,nostart/filname,gen ! filename for the expansion pass

resume ! brings up gen.db saved above/solu

expass,on ! activate expansion passseexp,gen,use ! options for the substructure expansion pass

expsol,1,1 ! THIS IS NEEDED ! (read about NUMEXP also) **************! OUTRES ,ALL,ALL ! not required for one load step solutionsolve

fini/POST1

/title,Stress in the Substructure/pbc,mast,,1 ! show master degrees of freedom symbols

/pbc,u,,1 ! show displacement constraints/pbc,rot,,1 ! show rotation constraints

plnsol,s,eqv ! look at the stress in the superelement

he above example, the user can change the mesh density. The numbers and positions of nodes along the common interface between the superelement and the normal portion of the model have to be the same for CPINTF to successfully connect the two parts of the model.

e model is created with the "bottom-up" approach. In the "use" part of this example, the superelement is read in with SE before the remainder of the model is created. If the remainder of the model was creat edbefore the superelement was read in, then the user would have to add statements t o control the node numbering, so that none of the master nodes coming in with the superelement would replicate the node numbers of the e xisting elements. If the superelement hasster nodes that have the same node numbers as the existing model, the model nodes will be redefined, and a mess will result. Check the manual, and look at the SETRAN command to act on the superelement, or at the NUMOFF command to act on the existing model, to prevent node replication problems. The PARSAV and PARRES commands can be used to put model parameter information into a coded file, and retrieve it after the /CLEAR command has beenued. The maximum node number can be put into a parameter by *GET and put into a file with PARSAV during the generation pass. It can be retrieved during the use pass by PARRES, and used to guide the offset of node numbers in either the already generated superelement with SETRAN, or in the remainder of the model with NUMOFF.

p Down Substructuring Example

e following example is NOT a substitute for a detailed understanding of ANSYS substructuring. It is for demonstration purposes only. Get the ANSYS Substructuring Tutorial guide and the Substructuring Guide for serious work.

e top down substructuring technique makes it possible to take an existing model, and have a portion of it changed into a substructure. This can boost efficiency in a number of ways, such as dealing with contact surfaces and gap elements, and handling very large models t hat have already been generated. In the example presented below, a model database is read in from a user-prepared file named "model.db". This model in "model.db" must have had a portion of thements grouped into a component called "super" using the command CM,SUPER,ELEM. This component will be rendered into a substructure. The intended substructure should, in general, consist of linear elements. The model must have had constraints and loads applied. The SFE command used in this example expects loads to exist inside the superelement, but should work without them. Some nodes can have been declared by the user to be master degrees ofedom. In order to create master degrees of freedom through the GUI, the analysis type has to be Substructure. In order to use the example below, the analysis type will have to be changed back to the type desired after creating extra master degrees of freedom -- usually to stati c analysis. Note that for dynamic analysis, master degrees of freedom are needed throughout the substructure -- they are not created by the example below. In the example presented, masterrees of freedom are automatically generated for the nodes on the i nterface between the component "super" and the remainder of the model. (There is no check for redundancy with user-declared master degrees of freedom.) The full model is used -- the analysis is not limited t o the selected set of elements in the file "model.db" when it is loaded. The example will automatically perform the substructure generation and the subsequent analysis, and will plot results t o plots. I have added a plot of the results for the full model, with results files for both the substructure and the non-substructure being read. There is no error checking in the example. This example has had li mited testing--let me know about errors.

en dealing with gap elements and/or contact surfaces, the usual procedure would be to select all the linear elements in the model (not the gap or the contact elements), and in this example, call them the component "super" for substructuring. Because the substructure matrix is usually much smaller than t he full model matrix, the iterations required for convergence with gap and contact elements will usually run far faster than iterations involving the full model, once thestructure matrix is generated. This makes otherwise infeasible modeling into a possibility.

dealing with extremely large models, where the objective is simply to deal with the size, not nonlinear elements li ke gap elements, there may little advantage in turning the entire large model into a substructure -- it could take as long to generate the superelement as to solve the model for one load case. It would be more common to turn portions of the model into one or more substructures. The connecting regions between the substructures would be chosen to involve asall a number of nodes as possible, to minimize substructure matrix size, and model wavefront size.

hough a MATRIX50 substructure superelement can undergo Large Displacement, it will act internally as a linear elastic structure. Methods to use MATRIX50 in nonlinear applications should be thoroughly tested by the user before application, including plots of displacement and stress to look for compatibility in results among the substructure regions and the remainder of the model, and checks that reaction forces equal the total a pplied forces. I have encounteredficulties combining Large Displacement with Substructuring -- see the image below.

use the following example: (1) Create a model, and (2) select a portion of the elements to become the substructure. Give this sel ection set of elements the component name "super" with the command "CM,SUPER,ELEM". (3) The model should have loads and constraints applied, and the analysis type defined. The analysis type must be acceptable for substructure use. (4) Save the model with the database name "model.db". (5) Call the routine below with the /INPUTmmand. Graphical results for the last load substep in the results files will be plotted to disk files. If run interactively, the user will have t o click the "OK" button a few times, and a plot to the screen should result when done. Expect warning messages related to partial element selection, and to reading from results files. NOTE: This example sets gravity load to ZERO in the "gen" portion of the analysis; otherwise, gravity would be DOUBLED on the superelement if ther's model includes gravity -- see the El ements Manual for MATRIX50. (If gravity is applied, be sure a density was applied to the materials in the model. If there is no gravity, the example can have the "seopt" command changed to NOT generate t he mass matrix for the superelement.)

e loading on MDOF nodes would also be DOUBLED if it was used in the superelement load vector, and used in the "USE" pass. For this reason, corrections to this routine have been added (Nov.2, Nov.4 1998). A complication for substructuring: Only a master node from a coupled node set or a constraint equation node group can be used as an MDOF for substructuring. This complication is NOT addressed in the present example. The example is for stress analysis. Ites not address centrifugal loading. To address other types of analyis, start with a look at the ANSYS Advanced User's Guide, and look at t he table of loads applicable in a substructure analysis.

tomating a substructure analysis is somewhat tricky -- this file will NOT be applicable to all types of analyses. I have been testing it with simple stress examples. The "POSTPROCESS" pass seems to work in loading stresses from the two different sources for viewing, "USE.RST" and "GEN.RST", although I haven't seen this documented. I tried the SUBSET command, but was getting warning messages about the nodal force and other results not necessarily beingrect. I haven't thoroughly investigated this. Have a close look at how the substeps are output with OUTRES and selected for expansion:

! "Top-Down" Substructuring Example -- In Development

!! - For information only. Use at your own risk.! - There is no error checking in this example.

! - Warning messages will be generated.! - ANSYS/ED supports very few master degrees of freedom.

!! WARNING: Gravity would be applied TWICE to the superelement if ACEL! were not zeroed in the "gen" pass. For models that do not

! include inertial loads, change the "seopt" command to generate! STIFFNESS only. See the Elements manual for MATRIX50.

! This example NOT designed for other inertial loads.!

! WARNING: In the "use" pass, nodal loads on superelement MDOF nodes! are deleted so loads on MDOF nodes are not counted TWICE.! FDELE and DDELE are used.

!! The model to be processed is in the file "model.db". The user must

! have identified the region to be substructured as the component "super"! with the command "CM,SUPER,ELEM" and saved the model as "model.db".

! Anything nonlinear in the component "super" will be treated as linear.! Analysis type is defined by the file "model.db" -- must be acceptable type.

! The "USE" pass has OUTRES set to write ALL substeps to the RST file.! The "EXPAND" pass has a *DO loop that expands solutions at ALL substeps.! The model must have had its loading and constraints applied.

! This example is for one load case only. Some Master Degrees of Freedom! can have been applied by the user -- needed for dynamic analysis.

! Master Degrees of Freedom Nodes will be generated between the substructure! and the remainder of the model. No check for redundancy is performed.

! Unless this file is run BATCH, the user will have to click the "OK" button

! whenever the CLEAR command is executed, and if error messages appear.!

fini ! finish whatever was active previously

/clear ! clear the database

/COM,############ GEN ############/COM,############ GEN ############

/COM,############ GEN ############

/show,part1,grp ! file for storing plots

resume,model,db ! read the model to be processed! - all loads and constraints must already be applied

! - the SFE command is employed in the "use" pass to! apply loads to the substructure

! - only one substructure generated in this example/filname,gen ! filename for the generation pass/prep7

allsel*get,nmx,node,,num,max ! get the highest node number

*get,nmn,node,,num,min ! get the lowest node numbercmsel,s,super ! select the elements identified as the component "super"nsle ! select nodes of these elements

esel,invert ! select the elements that are not part of "super"nsle,r ! reselect nodes connecting "super" to remainder of model

m,all,all ! make these nodes Master Degrees of Freedom (MDOF)cmsel,s,super ! select the "super" elements again

nsle ! select their associated nodesnsel,r,m,,nmn,n mx ! reselect all of these nodes that are MDOF (don't want nodes

! outside the "super" that the user called MDOF)

fdele,all,all ! delete loads on these MDOF nodes for "gen"ddele,all,all ! delete displacement loads on these MDOF nodes for "gen"

nsle ! select nodes of the component "super"/pbc,mast,,1

/pbc,f,,1/pbc,m,,1

/pbc,u,,1/pbc,rot,,1/title,Elements of the to-be-substructure

eplo ! plot the elements of the to-be-substructu refini

/soluantype,subst ! substructure analysis

seopt,gen,2 ! generation pass -- generate STIFFNESS and MASS matrices! - if no inertial load, change setting to STIFFNESS only

save ! save this part of model as "gen.db" for expansion pass

! - SAVE need not follow the command "solve"! - component "super" and its nodes currently selected

acel,0,0,0 ! set gravity to Zero AFTER "save" but BEFORE "solve"solve ! generates the "gen.sub" file

fini

/COM,############ USE ############

/COM,############ USE ############/COM,############ USE ############

/clear,nostart

/show,part2,grpresume,model,db ! bring the model in again. restores "acel" if any.

! "model.db" has to define the analysis type -- it should not! be a substructure generation

/filname,use ! filename for the use pass

/prep7allsel

*get,nmn,node,,num,min*get,nmx,node,,num,maxcmsel,s,super ! select the portion intended for the substructure

esel,invert ! select the remainder of the modelnsle ! select nodes of the remainder of the model

nsel,a,m,,nmn,n mx ! add MDOF nodes for visibility (not needed for solve)*get,ntp,etyp,,num,max ! get max element type number in the model in parameter ntp

et,ntp+1,50 ! new element type ntp+1 set to superelement MATRIX50type,ntp+1 ! set type ntp+1 before reading "creating" superelement with SEse,gen ! read in the superelement matrix from generation pass

! - master D.O.F. nodes already are at the interface! - no need to couple coincident interface nodes this example

! - new element number assigned should be above maximum*get,snm,elem,,num,max ! get the element number of the superelement just loaded

! - needed for SFE loading the superelement below! - extra work needed if more than one superelement

/pbc,all,,0/pbc,f,,1/pbc,m,,1

/pbc,mast,,1/title,Remainder of model attached to substructure

eplo ! plot the elements in the non-substructure plus "outline" view! of the substructure

fini/solu ! "model.db" analysis type for substructure is needed

SFE,snm,1,SELV, ,1 ! load applied in generation pass was in "model.db"! - apply load to to superelement number "snm" found above! - extra work needed if more than one superelement

outres,all,all ! save results for the all substeps of load step! - change here and "EXPAND" below if desired to change

solve ! results go in the file "use.rst"save ! save "use.db" to optionally review non-substructure results

fini ! "use.db" and "use.rst" now contain non-substructure results/post1set,last ! plot results at the end of the load step

/title,Stress in the non-substructure elementsplnsol,s,eqv ! show nodal stress in the non-substructure

*get,lastlstp,a ctive,,set,lstp ! get the last load step number*get,lastsbst,a ctive,,set,sbst ! get the last substep number

parsav,scalar,p arameterstore,par m ! store them in file for retrieval belowfini

/COM,############ EXPAND ############/COM,############ EXPAND ############

/COM,############ EXPAND ############

/clear,nostart

/show,part3,grp/filname,gen ! filename for the expansion pass

resume ! brings up "gen.db" saved above, "super" is selectedparres,new,para meterstore,parm ! retrieve data on last load step/substep

! parres must follow resume statement/solu

expass,on ! activate expansion passseexp,gen,use ! options for the substructure expansion pass*do,iii,1,lastsbst

expsol,lastlstp,ii i,,yes ! expand result at last load step/substep! - (read about NUMEXP also)

outres,all,all ! all data writtensolve

*enddofini ! "gen.rst" now contains substructure results, last step/POST1

/title,Stress in the Substructureplnsol,s,eqv ! show nodal stress in the substructure

save,stresses_in_super,dbfini

/COM,############ POSTPROCESS ############

/COM,############ POSTPROCESS ############/COM,############ POSTPROCESS ############





!! WARNING: The following is my own invention; use at your own risk.

! Warning messages will be generated by ANSYS.resume,model,db

/show,part4,grp/post1cmsel,s,super

nslefile,gen,rst

set,lastesel,invert ! Select the elements NOT in substructure component "super"

nsle ! Select the nodes of these elementsfile,use,rst ! Point to file "use.rst" that contains the rest of the resultsset,last ! Read in load step data for selected elements, last substep

esel,all ! Select all elementsnsle ! Select the nodes of the elements

/pbc,all,,0/pbc,f,,1

/pbc,m,,1/pbc,mast,,1/title,Stress in the Full Structure

plnsol,s,eqv ! Show nodal stress for the full model.! Because of averaging, PLNSOL stresses on the interface of the

! substructure and non-substructur e regions cannot exactly! match values for these locations plotted separately, above.

! Element stress and displacement should exactly match in! a small displacement linear analysis.

save,stress_allelem,db ! Save the model with all stresses on elements

/show,term ! Back to screen -- only works if used interactivelyplnsol,s,eqv ! Show the stress results for all elements if interactive ANSYS

e "top down" example saves the results of t he "use" pass and the "expansion" pass in database files. These can be loaded to inspect results in the non-substructure and in the substructure parts of the model, respectively. If the file i s run interactively, the user will have to click the "OK" button each time the /CLEAR command executes, and for a variety of warning messages that can appear. It may be preferred to run the file under Batch control, and to later review theults in the plot files, and in the resulting database files. Remember to check for error and warning messages. Because of the complexity of substructure analysis, the user should run checks on balance of forces, and do other typical checking of results.

ge Displacement Nonlinearity and Substructure: The ANSYS 5.5 Advanced User's Guide, Chapter 5 gives more help on large rotation (large displacement, geometrically nonlinear) substructured analysis than at the 5.3 level. Note the comment that c onstraints should be applied in the "use" pass, not in the "gen" pass, for large rotation analysis.

he file "model.db", used in the above example, has had Large Displacement activated with " NLGEOM,ON" then a nonlinear solution will be sought. Convergence criteria, ramping of loading, substeps, and other nonlinear controls may be desired. Because the substructure will act li nearly internally, convergence may not be as easy as the user would wish. When the run does converge, the results will not be an exact match for the result without substructuring. Theput plots should be examined to see if they read "Substep 999999", indicating failure to converge. If you test the above example with Large Displacement, use a Large Displacement model that converges easily without a substructure approach. An attempt has been made in t he above example to cope with a model that develops the Large Displacement solution in a load step containing a set of substeps. This is the reason for statements t hat record the last loadstep andstep numbers. However, the example does NOT reserve application of all DOF constraints for the "USE" pass, as recommended in the ANSYS 5.5 guide, so it will NOT be appropriate for models with constraints applied to non-MDOF nodes in the substructure region. The user can get around this by manually assigning MDOF to all the nodes to which constraints a re applied in the component "super", in "model.db".

e master degrees of freedom for the superelement must have rotational degrees of freedom for Large Displacement work. The user can try assigning MASS21 elements to the master degree of freedom nodes if the elements in t he model do not have rotational degrees of freedom. The MASS21 elements can have a REAL value that contains zero values for the masses and mass moments of inertia. This will introduce the requisite rotational degrees of freedom.

en using elements like SHELL63, which have rotational degrees of freedom, I have encountered a rather odd result: The Large Displacement solution for the elements i n the superelement (stored in "gen.rst" in the example) is for the displacement of the substructure nodes with respect to a coordinate system embedded in the superelement, not with respect to the global axes. This is not the case for small displacement solutions, which appear displaced correctly. Sincesuperelement can undergo large rotation, the displacement that is reported and plotted for the nodes inside the superelement will be far smaller than the displacement reported and plotted for the remainder of the model, in a Large Displacement solution. This is because the coordinate system embedded in the superelement moves with the superelement. In li mited testing, the SEQV stress plots appear to be OK, if the l oad step that is to be expanded is identified

perly. I have not investigated what happens to stress components in the Global and Ele ment Coordinate Systems. Rotational transormation of the stress and strain tensors could be very complex. See t he image below for a result combining SHELL63 elements, substructuring, and Large Displacement.

ossible visual displacement fix (for the displacement plot problem of 6 DOF elements in Large Displacement substructures) is to transform the displaced position coordinates of the non-MDOF nodes in the superelement on the basis of the rotations and translations of the origin of the superelement in Global Coordinates. The origin of the superelement will be the MDOF node that reports no displacements or rotations inside the superelement (in superelementrdinates); it appears to be the MDOF node with t he lowest node number. Applying a transformation properly will require deducing or looking up the order of the sequence of rotations that ANSYS uses in Large Displacement work, or that ANSYS uses to report node rotations. A reading of the Theory Manual suggests that ANSYS internally uses quaternions for large displacement rotations in space. This would be for the usual reason that quaternions do not have a

gularity in any orientation, in contrast to Euler angles. It appears that the rotations reported at a node represent 3-D components of a single rotation vector, rather than Euler or other angles, so the transformation will need to be based on rotation about a vector that starts at a known point in space (the origin of the superelement), plus translations. I will be working on this as my next project for t his web page. The reported rotation may be complicated by rotated nodalrdinate systems (NROTAT) or superelements that the user has employed... this will require checking. Reader feedback would be appreciated. If I get anywhere with this, I will limit myself to displacements only. Transforming stress tensors would be a bit much!

e above plot was generated using the above sample /INPUT file on a Large Displacement model of a cantilever beam created with SHELL63 elements. A simil ar displacement discontinuity results with BEAM4 elements in a similar application, as shown in the images below:

46: Plot Applied Temperatures

thermal stress analysis, temperatures will be applied as a "l oad". Temperatures can be applied to nodes with the BF command, to elements with the BFE command, or implied using other commands. (Check the BFE command and the element type in the ANSYS documentation for details on using BFE.) A colored element plot of applied temperatures can be generated by using the commands /PBF,TEMP,,1 and EPLO, whichShows body force loads as contours onplays, per the ANSYS Commands manual.

en using beam, link, and pipe elements, if the element thickness is shown with the / ESHAPE command before executing EPLO, temperatures can be made visible with contour coloring for these line ele ments. It may be desired to exaggerate their displayed thickness with /ESHAPE in order to make the temperature information more visible.

47: Skipping Over Statements in an ANSYS Input File

SYS commands can be developed in a file that is executed with the /INPUT command. This can permit very flexible and sophisticated use of the program. Here is a well known programming trick that can be used t o temporarily skip over part of an ANSYS input file. Set a parameter ("SKIP" in this example) t o a value that te lls an *IF statement to jump over a section of code that you want to skip. This is much quicker than commenting out a block of code, or cuttingpasting as an input file is developed and modified. *IF statements that use this parameter could be located in a number of positions in the input file -- this permits changing the value of one parameter at the beginning of the input file to cause skipping of input code in a variety of l ocations.

! Input code to ANSYS...! ...

SKIP=1 ! Set to 1 to skip, 0 to run the code inside the *IF...*ENDIF commands*IF,SKIP,EQ,0,THEN

! ANSYS commands that are optionally executed...

*ENDIF! ... more code follows

ce there is no compilation of the input file, the "skip" technique uses l ittle time in choosing to execute or bypass the blocked off commands (ANSYS still has to read the blocked out code in order to check off the number of *IF and *ENDIF commands).

48: Static Analysis Followed by Transient Analysis

nsient analysis by ANSYS can model transient vibrations, or the dynamics of a flexible mechanism in motion, in addition to more complex effects. Initial conditions can be applied, followed by transient analysis. One t ype of initial condition is a zero velocity initial position with stored energy. The stored energy can be potential energy of position, elastic energy, or both. Another initial condition is an initial velocity. A model can have both initial velocity and storedrgy. A static analysis may be desired to develop the stored elastic energy, before starting a transient analysis. Remember that for transient analysis, the mass of the model must be input in the appropriate mass units, not as weight.

e following ANSYS input file illustrates the execution of a linear elastic static analysis that sets an initial condition, followed by a transient analysis. The model is of a cantilevered beam that has a force applied to the free end in a static analysis. The transient vibration that results when the force on the free end is removed is obtained. No gravity is used. No damping has been applied, and ANSYS defaults for the numerical integration are implicit. This is a linear elasticution, so the numerical integration should be stable, given the ANSYS algorithm used. The t ime substep size for the transient analysis should be smaller than 1/20 of the period of t he first few modes of vibration. (The user could tweak the ANSYS numerical integration parameters so that very high frequency response modes are numerically damped. Stability in Large Displacement nonlinear transient analysis is probably not guaranteed, although damping and smalle substep size should help.) The use of a consistent mass matrix (default) should in general yield more accurate results than a reduced mass matrix i f the element density is coarse, however the use of a reduced mass matrix may shorten the solution time in large models. The movement of the tip of the beam is plotted -- it is not a perfect sinusoid because the initial deflected shape of the beam is not an exact match to a mode of vibration.

! Transient vibration, cantilever beam, "plucking" the tip.! For illustration purposes only. Use at your own risk.

fini/clear ! Start fresh/title,Transient Vibration of Cantilever Beam

/PREP7ET,1,BEAM3 ! 2-D model of beam

R,1,1,1,1 ! beam crossection propertiesMP,EX, 1, 30000000 ! Young's modulus, BIN units

MP,DENS,1, 7.34E-04 ! beam mass density, BIN unitsK, , 0.0 ! keypointsK, , 10. ! 10" long

L, 1, 2 ! lineLESIZE,ALL,,,8, 1,1 ! 8 element divisions

LMESH, 1 ! mesh with beam elements

FINISH

/SOLUANTYPE,4 ! Select transient analysis

F,2,FY,-50000 ! apply down force on RHS node (unrealisticall y high)d,1,ux ! constrain first node at LHS, in X direction

d,1,uy ! in Y directiond,1,rotz ! and constrain rotation

time,0.0005 ! small time increment, staticOUTRES,ALL,ALL ! save all substep results

timint,off,all ! no time integration -- treat as Steady Statensubst,2 ! two substeps to imply zero initial velocity for transient

kbc,1 ! step change loadsolve ! find the static deformed shape

TIME,.002 ! time at end of transient (pre-determined to show oscillation)NSUBST,100 ! time steps small enough to show vibration

KBC,1 ! step change loadfdele,all,all ! delete force -- show vibration after force is released

OUTRES,ALL,ALL, ! save all substep resultstimint,on,all ! activate transient analysis

solve ! find the transient vibration of the beamfini

/post1/dscale,1 ! automatic scaling, to easily view final result

pldisp,1 ! show final deformed shapeFINISH

/POST26

NSOL,2,2,U,Y,UY ! results variable for plotting/title,Transient Vibration of Cantilever Beam: Motion of Tip

PLVAR,2 ! graph oscillation of the tip of the beamFINISH

TE: The use of the TIMINT command controls activation of the st atic and transient portions of the solution. The stat ic solution is obtained at t wo time substeps so that an i nitial velocity of zero is implied. An animation of the transient solution can be generated for the full beam in /POST1, showing the transient vibration in action. For an animation, the user will have to set a satisfactory displacement scaling value with the command /DSCALE, not use automaticling. In the animation of the Large Displacement motions of a mechanism, a /DSCALE setting of 1.0 will generally be wanted, so that angles of rotation l ook correct. A zoom setting other than /ZOOM,OFF will usually yield a better animation.

49: File Compression for Model Storage

o restart is to be executed on an ANSYS model, it will often be sufficient to save only the model database file (*.DB) and the results file (*.RST) when archiving an ANSYS model. If the model was generated from command input files, these will require storage. If only one load step was written to t he results file, the results file may not require archival if t he results are also contained in the database file. Load case, graphics output, and other fil es may be wanted forhival. The database, graphics, and results files can be extremely large. They often compress well using data compression programs such as the UNIX compress and gzip utilities (gzip is more powerful than compress). On Windows computers,gzip is also available for NT (it handles long file names), in addition to the shareware ZIP utilities, though you will need to dig on the Internet to find gzip for Windows NT -- have a look at GZIP on the web and look forructions and the version for your computer (test before use). In FEA work, I find the advantage of the gzip utility to be that the compressed file name is simply the original file name with .gz appended, and the uncompressed file is removed. The data storage requirement may be reduced by roughly 25% to 80%, both on the hard drive, and on tape or removable disk. The data compression is significantly more effective, though much slower, than with the disk

mpression scheme that can be used by Windows NT 4.0, which also does not keep the files compressed when they are sent over a network, or otherwise moved around. Hint: Make sure that those who will decompress the files i n future will know how to do it!

50: Organizing Large FEA Models

amining the results of an FEA model, selecting and modifying portions of the model, and keeping a record of what MAT (material) and REAL (shell thickness, beam size, etc.) values were used for various parts of a model becomes very difficult with large FEA models. A very l arge structure represented with hundreds or thousands of individual beam elements or areas meshed with shell ele ments, will require that the identities, materials and REAL settings for large

mbers of parts be organized and recorded.

ere is no one way to do this. Individual parts, or groups of parts, can be defined to be components that are accessed by names of up to 8 characters. These parts can be geometric entities, elements, or nodes. Macros can step through all the components using *GET commands. Collections of components can be grouped into component assemblies. An individual assembly could be created for those components that are to be selected under certain circumstances, forlysis or for results review. The use of components makes it possible to refer to either a part or a subassembly by one name, and easy to select it. The creat ion of a component can save a set of entities that were sele cted with a certain sequence of select logic, and be used in the enhancement of the ANSYS select logic process. The database component commands are: CM, CMDELE, CMEDIT, CMGRP, CMLIST, and CMSEL. A macro can be written that will step

ough all components, plotting them, including the component name and information on it in the plot title, or an annotation.

her REAL values for elements and entities, or MAT values, can be used to identify parts in a model with numbers. (The element type will have to support a REAL value if a REAL is to be created for that element type. However, a REAL value can be forced on an element even i f the element type does not admit assignment of a REAL. This can be done when creating an element, applied to the geometric entity that is to be meshed with the element, or forced after thet with EMODIF. When EMODIF is used, be cautioned that in a re-meshing the REAL assigned to the geometric entity will be used. When the element type does not accept a REAL sett ing, the R setting can simply be left blank. In that case, the commands NUMMRG,ALL and NUMCMP,ALL can make a mess and should not be used in this all-inclusive form -- stick to specific forms such as NUMMRG,KP.) In a model made of shell el ements or beam elements, formple, each plate or beam could be described with its own REAL value, even though there may be many plates or beams of a given thickness or size within the model. Where a group of parts will always be chosen with the same REAL value, they could share one REAL setting. This makes changing the shell thickness or the beam characteristics very simple, and provides easy part selection with commands like ESEL, ASEL, or LSEL, as appropriate, according to theirAL value, or a range of REAL values. An array (see the *DIM command) could correlate REAL values with other information, such as part names (with an 8 character limit). The same approach can be taken with the setti ng of MAT values for describing the material properties. Using material numbers for part i dentification, however, could get cumbersome, because there are such a large number of individual material property settings, and they may be temperatureendent in some models, or include material nonlinearity.

nd it helpful NOT to set any of the geometric entities or elements in a large model to a MAT or REAL value of one. One is a default value t hat is sometimes assigned when no value has been assigned by the user. Geometric entities may have a value of zero when nothing has been assigned. I can then select things that have a MAT or REAL of zero or one to check on whether I have forgotten to assign a value to any part of the model. Plots with coloring assignedording to REAL or MAT will help in checking a model.

en REAL or MAT values have been used to differentiate between different parts of a model, the user must be careful not to use a NUMCMP,ALL or NUMMRG,ALL command on entity numbering, because it will compress or merge out REAL and MAT values. This wil l destroy the identification scheme. The NUMCMP command will have to be called with the specific quantities to be compressed individually identified, such as NODE, as in the manual.

en the parts have been identified by different REAL or MAT numbers, a coloring scheme based on REAL or MAT can be used during element or geometric entit y plots, to improve identification of the parts of a model, and the appearance of the FEA plot. Caution: ANSYS does not use a "4 color map theorem" when plotting (can't do this in 3-D anyway) so parts of differing REAL or MAT may be adjacent and have the same color.

ays could be used to assign numbers to component names, and to keep track of what REAL values were used by the elements within components. Arrays could assign 8-character names to the parts described by different REAL values. Arrays could be used to set several values of a number of shell thicknesses or beam sizes to be examined i n a series of analyses that are to be run automatically. As discussed above, this parameter information can be included inotations during model and results plotting, making model review easier and less error-prone.

51: Selecting Nodes in a Stress or Strain Range

e selection of nodes in a certai n stress range can be effected with, for example, the command NSEL,S,S,EQV,40000,9999999 in order to get nodes with EQV (Von Mises equivalent) stresses from 40000 to 9999999. This and similar commands can be used to get at only the portions of a full model that are significantly stressed.

e effectiveness of this command can be compromised somewhat by nodal stress averaging, shell stress surface selection (TOP, MID, or BOT), and other complications. The command would typically be followed by the two commands ESLN and NSLE to be able to plot the associated elements and their stresses.

he above part identification scheme using REAL values has been employed, the stress level selection command could be followed by a macro that selects al l parts that match t he REAL types of the selected ele ments. This would make it possible to see all highly stressed parts. This approach is helpful with complex models with parts visually hidden by other parts.

52: Selecting Nodes that are Subjected to Nodal Coupling

des that are coupled can be selected with commands such as NSEL,S,CP,,1,999999 in order to show only the coupled nodes, and to have t he option of using picking to delete nodal coupling, or for other purposes. Once coupled nodes have been selected, work to evaluate the forces resulting from the coupling can begin. Similarly, nodes can be selected according to their presence in constraint equations (CE), their applied displacement (D), forces applied, and othereria -- see the NSEL command for further information.

53: /NOPR and /GOPR Speed Up Input Files and Macros

en a long input file or macro is read while running ANSYS interactively, text information is written to the output screen and optionally to an output file. If a significant number of *GET and similar operations are being executed, a large quantity of text information will be written t o output. If the input files and macros are known to be fully debugged, they may execute faster if they start with /NOPR and end with /GOPR in order to switch off text output while they arening. If their execution is causing geometry, nodes, or elements to be generated, a speedup may result from temporarily switching off the generation of graphics with IMMED,0 and /SHOW,OFF. They can be re-activated with IMMED,1 and /SHOW,TERM. You may want to consider the /UIS command also.

54: Using Commands IMMED and /UIS and /SHOW,OFF to Suppress Plotting

metimes develop a model interactively, setting up some dimensions as parameters, then manually modify and add to the log file that is generated. The resulting log file becomes an input file that I can use for parametric generation of a model. When I run this input log file, I don't want all of my various plot commands to be executed, only those for finished model display and results review. This can be implemented with the IMMED,0 (for interactivecution), /UIS,REPLOT,0 and /SHOW,OFF commands. They can be re-activated with IMMED,1 and /UIS/REPLOT,1 and /SHOW,TERM. If the graphics output is intended to be sent to a graphics file, the command /SHOW,FILE can be used for re-activation of writing to a file previously designated by a /SHOW, filename command. If writing to a file, the immediate mode plotting is off by default. Be warned that if you change to another output graphics filename

h the /SHOW command, then come back to the first filename, the first file will be overwritten.

en re-running a log file using /INPUT the messages that required clicking " OK" will be generated and execution will pause. This means that the /INPUT command will not re-run all log files unattended.I have not found the /UIS command to completely stop this, such as when the /CLEAR command is i ssued. Running batch is sometimes desirable.

55: What's the Bauschinger Effect? Comments on Material Yield

st wanted to do elastic/ plastic analysis in ANSYS to get a feel for the onset of failure in an automotive part. It was of value to show that one proposed crossection shape was significantly better than another. This required me to use plastic material properties for steel, in nonlinear large deflection analysis in ANSYS. Unfortunately, I had taken neither an academic course in metal forming, nor attended an ANSYS course in nonlinear analysis. Digging into the ANSYSnuals, the first thing one has to decide on is whether to use Kinematic Hardening or Isotropic Hardening for the material model. Fortunately, high precision was not needed for what I was doing, so the exact stress/strain curve and the choice of material yield rules were not a big concern. Still, I wanted to know what I was doing, within reason. The manual mentions the relationship between kinematic hardening and the Bauschinger effect. After some poking around, Ially found a basic description of the Bauschinger effect in Timoshenko's Strength of Materials Part II: Advanced Theory and Problems Third Edition, Krieger, Florida, 1976.

entially, a tension test ca using slight yielding permanently deforms (causes slip in) unfavorably oriented crystals before other crystals in a specimen. Consequently, upon unloading, the permanently deformed crystals are in some compression. After re-loading with tension, the onset of yield is raised because the deformed crystals do not reach their new slip stress until the load is higher than the first time. If the material is compressed after tension loading, the deformedstals reach their compression slip stress before the rest of the crystals, with the result that compression yielding starts sooner than in a fresh unstrained specimen. Quoting Timoshenko, "Thus the tensile test cycle raises the elastic limit in tension, but lowers the elastic limit in compression." This is the Bauschinger effect.

e thing that may affect the choice of a yield model in ANSYS will be what is supported by an element type. Shell 63 does not support nonlinear material properties at all . Shell 181 supports isotropic hardening but not kinematic hardening. Shell 43 apparently supports both, but it is suggested that Shell 181 is more capable.

hould be remembered that ANSYS requires a true strain curve i n material characterization, not the engineering strain curve, when multilinear curves are entered. In quick-and-dirty checks on the possibility of failure of a structure, I sometimes consider it sufficient just to use a bilinear model, with the yield portion of the curve fairly flat. This wouldn't do for models of metal forming in manufacturing, but can sometimes be used to assess whether structure failure is acern when some portions of an elastic model are exceeding yield. It may be desirable to load the structure beyond the design load in order to observe where significant failure starts, in order to get a feel for margin of safety. This may require arc-length analysis. (My use of the word "quick" in "quick-and-dirty" is overly optimistic.)

me design codes have rules for elastic-plastic or for fully plastic analysis that would have to be used, if such an analysis was needed t o justify or qualify a design legally or to fulfill a contract.

56: Thought Experiments

thing so focuses the mind on the design details of a product as hearing that it failed in testing or in service. You don't have to be Einstein to perform the following thought experiment: Suppose that you heard that some aspect of a design had failed in service. The failure could be yielding, buckling, crack growth, fracture, vibrating to death, unacceptable deformation, wear or binding, or whatever is appropriate. Brainstorm as to whether it could happen, what could havesed it, and how analysis could highlight what is or could be wrong. Do this thought experiment for as many characteristics of the product as you can. You may substantially extend the number of things that you consider in the design, and in the FEA work. It may save someone's neck, either figuratively or literally.





sibilities and "What If's":

What could cause yielding -- are fasteners or welds overloaded? Were their loads even checked -- and for all load cases, or the bounding load cases? Are the bounding load cases complete? Are stresses above yield over a significant region? Are surface stresses of shell elements doing something unusual? Were nonlinearities considered? Were all possible combinations of loading considered? Is there a high load situation that was not considered? Were all components evaluated in FEA? Is there anunusual boundary condition arrangement that has not been considered? Was the FEA mesh too coarse? Were relevant details that cause stress concentrations left out of t he model? Can what was discounted as a local stress concentration lead to progressive collapse or crack growth?

Can buckling arise? Have both linear and nonlinear approaches to buckling possibilities been considered? Has a portion of the model been represented so simplified that buckling possibility is not detected? Has nonlinear buckling been considered at loads greater than the design loads, so that some sense of the margin of safety is obtained? Can restraint of thermal expansion cause stress and buckling?

Crack Growth -- what details exist that could possibly be sites for crack growth? Do surface stresses give any warnings? Where could details be included to reduce crack growth possibilities? Are regions that have geometry that could lead to crack growth highly stressed and/or cyclically stressed? Is direct tension on welds causing Type I fracture loading? Is shear, bending or torsional loading (applied forces and moments, and/or applied displacements and rotations) on structural details causing Type II oType III fracture loading on welds? Is the loading significant? Is fatigue an issue? Is fracture analysis warranted? Is there a reliable shortcut guide to what is tolerable? Is such a guide even possible? Could crack growth be so rapid that it happens between inspections and causes sudden fracture? Are cracks detectable at a size t hat does not immediately cause fracture? Should inspection intervals be more frequent when the product is new?

Vibration -- what loading could stimulate vibration? What frequencies could drive vibration? Is there adequate structural damping or are there other mechanisms to suppress trouble? Where are the natural frequencies of vibration? Do steady state responses or random vibration responses need to be evaluated? Is f low induced vibration a possibility? Will sound and noise cause destructive vibrations? Have all possible boundary condition arrangements been included in assessing vibration?

Will large deformations go outside of what is acceptable? Is the structure stiffness high enough for the product use? Will deformation cause loss of function, contact with the surroundings, binding, interference, collision, or excessive wear of moving parts?

Is the design something that can be manufactured with the quality and uniformity required to avoid structural weakness?

e analyst should extend the above items to e verything that needs to be considered, or that could go wrong.

57: Control of Meshing

ce I am using ANSYS 5.3, I can't comment on t he latest in ANSYS automatic meshing capabilities, but a couple of suggestions about the basics may be helpful. You can select the lines that have not yet had mesh density applied, with the command "LSEL,S,NDIV,,0" as a check that all lines have had mesh density applied, or for convenience. The same t ype of command can be used to find the l ines with other mesh densities.

ic ANSYS training should have taught you that line and area concatenation can help you get mapped meshing, which gives relatively neat regular meshes such as all four-sided area elements, or all six-sided solid elements. This can make a big difference in some models.

58: Four View Plot

en assessing modes of vibration or deflection of a 3-D structure, I have found it convenient (though slower) to generate ANSYS plots showing my model in four views on one sheet of paper or screen plot. The traditional views: Front Elevation (front), Plan (top), Side Elevation (right), and Isometric (iso), can be positioned in four windows that are located in the lower left quarter, upper left quarter, lower right quarter, and upper right quarter of the plot, respectively.her standard view layouts can be substituted). A displacement plot of a mode shape with PLDISP or PLDISP,1 with these four views active will leave fewer ambiguities about what is happening with mode shapes than a single-view plot. The only shortcoming is that the images are small -- I prefer to use 11" x 17" paper in landscape mode for these plots.

annecdote I heard from a guy I knew: A U.S. ship entered a foreign shipyard needing a new propeller. The ship's engineer supplied a drawing, and a propeller was ca st and installed. The ship was launched and powered up. When set to go forward, the ship went backward -- the shipyard used the European standard view interpretation of an American drawing, and the propeller was mirror imaged!

e following code can be put into a macro to generate a four-view screen. Customize it as you wish -- I include commands to turn off PowerGraphics and to use Centroidal sort. This permits clean plots on paper with large models. NOTE: Users may want to set the /DSCALE value to the same level in all four windows with "/DSCALE,ALL,value".

! For information only. Use at your own risk.

! Put these lines in a macro! Set screen to show four standard views:! User may want to set /DSCALE to the same value in all windows

/WIN,1,LTOP ! Window 1 left top/WIN,2,RTOP ! Window 2 right top

/WIN,3,LBOT ! Window 3 left bottom/WIN,4,RBOT ! Window 4 right bottom

/WIN,5,OFF ! Turn off Window 5/VIEW,1,0,1,0 ! Window 1 top (plan) view/VUP,1,Y ! Reference orientation

/VIEW,2,1,1,1 ! Window 2 ISO (isometric projection) view/VUP,2,Y ! Reference orientation

/VIEW,3,0,0,1 ! Window 3 front (front elevation) view

/VUP,3,Y ! Reference orientation/VIEW,4,1,0,0 ! Window 4 right (side elevation) view

/VUP,4,Y ! Reference orientation/AUTO,ALL ! Fit all windows

/PLOPTS,INFO,1 ! Include information column/PLOPTS,LEG2,0 ! Don't include view information

/TYPE,ALL,2 ! Centroid sort, better print that Z-buffer/CPLANE,0 ! Cutting plane

/graphics,full ! NOT PowerGraphics (fewer facets?)! User has to issue the plot command

e next code can be used in a macro to return to a front view in one window. Again, the user may want to customize some of the lines:

! For information only. Use at your own risk.

! Set screen to show one front view in Window 1/WIN,1,SQUA ! Full square Window 1

/WIN,1,ON ! Turn on Window 1/WIN,2,OFF ! Turn off Window 2

/WIN,3,OFF ! Turn off Window 3/WIN,4,OFF ! Turn off Window 4/WIN,5,OFF ! Turn off Window 5

/PLOPTS,INFO,1 ! Info on for right column/PLOPTS,LEG2,0 ! Don't show the view information

/VIEW,1,0,0,1 ! Front (front elevation) view/VUP,1,Y ! Reference orientation

/TYPE,ALL,2 ! Centroidal sort, better print than Z-buffer/CPLANE,0 ! Cutting plane

/graphics,full ! Not PowerGraphics (fewer facets?)! User has to issue the plot command

er running one of the above view-generating macros, the user has to issue a plot command to see the result.

59: Quick Review of Mode Shapes

start printing plots of mode shapes directly from ANSYS mode shape results, having the hardcopy window pop up automatically, type in an input line such as:

SET,1,1$PLDISP$/UI,COPY

e dollar sign separates the commands that are grouped on one input line. Click the hardcopy OK button to kick off the hardcopy. You may want to set the print to la ndscape mode, first. Then, to print plots of the rest of the mode shapes, type:

SET,NEXT$PLDISP$/UI,COPY

mply keep repeating the second line (to avoid re-typing, double-click it in the ANSYS Input window), and clicking the hardcopy OK button, to get the rest of the modes printed. Note that the SET,NEXT command will loop back to the first mode shape after the number of modes stored in the RST file has been exhausted.

u may see the somewhat odd message:

s comes up because of the /UI,COPY command, and has something to do with the /ZOOM command. Consequently, this method may not work satisfactorily if your zoom is not off. In viewing mode shapes, it will be typical to have zooming off.

e following code fragment read from an input or macro file can automatically plot a set of mode shapes. *GET commands are used to detect information on what substep and frequency are read. The user does not need to know how many modes were generated, so automated plotting to a file is simpler. The displacement plots will contain substep and frequency information. This code should cope with degenerate eigenvalues or rigid body displacements. Execute t hism within /POST1 after a mode case analysis was run, or after the database and RST file for a mode case analysis are loaded. There is no error check, so this must be used properly. The user will want to test and customize these commands:

! For information only. Use at your own risk.set,1,1 ! set to the first mode

pldisp ! plot the first mode*do,iii,1,99999 99 ! use a very large number

set,next ! set to the next mode*get,ntotal,acti ve,0,solu,ncmss ! cumulative substeps -- cycles to 1 if all modes in RST done

*get,thefreq,mod e,iii,freq ! use this line if desired to get frequency into a parameter*if,ntotal,eq,1,then*exit ! exit do loop if done

*endifpldisp ! plot the displaced shape

*enddo

60: Using ANSYS Help

en using ANSYS interactively, help on any command can be accessed immediately by typing HELP, commandname into the input window. If the HELP a pplication has been launched independently, the quick way to get help on a particular command is to use the " Navigate" and "Help On..." menu choice. Type the command name into t he "Help On" text box that pops up, then click the Apply button.

s will send the help program to the Commands manual for the command name typed. If you click the "Apply" button, the "Help On" dialog box remains visible, and can be used to type in other command names.

e online ANSYS help system makes the need for trips to hard-copy documentation much less frequent. The Help application can be launched while ANSYS is running in the background, so ANSYS documentation can be studied while a large model is solving.

61: The FEA Job Hunt

t strictly an ANSYS issue, I want to put in my own two cent's worth on this topic, which is of interest to all of us. Some time back when I was job hunting during a recession, I was given a pre-screening interview over the phone. The interviewer owned a consulting firm. It rapidly became apparent that he had been lied to, many times and by many people, about their FEA experience. I had been using a company's proprietary FEA code and was not experienced with theor commercial programs, so was immediately suspect. Another time, I heard of an applicant using another guy's FEA model images to present in a job interview as "evidence" of his own experience. I interviewed a guy who claimed experience with "a locally available product I wouldn't know." It became apparent that he had been coached and knew only the buzz words. When job hunting it is challenge enough to compete with other experienced people --representation we don't need.

e FEA job applicant should be able to present evidence of academic and/or post-academic training. The applicant should have a portfolio of previous work. The applicant should be i nstructed to bring these to the interview. The portfolio information can be a little awkward when the products are proprietary. If it would be illegal to present any images of work done, then I suggest a keen applicant independently develop a set of small models using ANSYS/ED thatstrate the FEA techniques with which the applicant is familiar. The applicant should be able to describe the modeling considerations, techniques, compromises, pitfalls, and post-processing possibilities of the examples.

course, with good references and personal networking, the above situations are less of a c oncern. Still, as with computer programming, the productivity of individuals can vary surprisingly. Consequently, the applicant should be able to describe what makes FEA productivity possible, some of the modeling shortcuts possible, and give an energetic, articulate and confident presentation of self.

estions of the "how would you model this" and "how would you handle this" type are just as relevant as they are in other professional interviews.

ve had both excellent and very poor interviewers assessing me. With some, I've had to politely direct the interview just to be able to point out my range of skills. On the basis of my own small set of experiences I would say that first i mpressions are very telling -- if you get a bad feeling about a place during the interview, it may be for a good reason. If you see a place as being a welcoming workplace with a healthy environment, and the people you meet behave well

are socially skilled, the odds are that as long as you function as a valuable employee, life there will be OK. I've had an interviewer keep me waiting for an hour and a half past t he appointment time. I got the job, and found that things were frequently out of control, and the guy was impossible to see. I had an unpleasant "stress interview", and sure enough, the place was cheap, had an unhealthy work life, and poorly structured leadership. Another interviewer struck mehighly manipulative, trying to goad me into making negative comments about employers and ethnic groups (of all things--talk about playing with fire--a personnel manager who apparently fancied himself a psychologist), and giving me inaccurate data on hiring intentions. A friend of mine got the job and detested it, saying the place was poisoned with political games. I've had a t horoughly positive interview, got the job, and found I was with great people. Ignore theirpe: What you see is (most likely) what you get.

end this on a few positive notes: Employers want to hire someone who will be a success for them. Your boss will be very happy if you make everyone's life easier through your contributions. Prepare yourself to give a picture of your range of skills, energy, confidence, communication skill, ability to work with others, range of past experience, and ability to time-manage a set of responsibilities. Some employers begrudge every penny, but others are pleased tompensate you attractively if you produce well. Size up the potential employer carefully, for your time is valuable. Best of l uck.

62: *VPUT and DESOL

ve no idea why the commands manual entry for *VPUT describes the parameter ParR as "The name of t he resulting vector array parameter." The parameter ParR is the source of data, NOT what is changed by *VPUT. Note that *VPUT can write to node results, and to an el ement ETABLE. There is a difference between writing to "nodal degree of freedom results", and what the manual calls "element nodal results" with *VPUT.

e *VPUT command can write information to the node results which can t hen be plotted as if i t was the nodal results, using the PLNSOL command. The command manual tells us that the e ffect is permanent for degree of freedom results (changing the database), but temporary for all others (derived results, not changing the underlying database). Writing stress data with *VPUT does not affect element plots with PLESOL,S,option. If you use *VPUT to write to "elementdal stress results", immediately do a PLNSOL plot to see the effect, do a PLDISP plot (seeing unaffected degree of freedom data), and then do another PLNSOL stress plot, the la tter PLNSOL plot shows original data that is unaffected by *VPUT. The temporary modified PLNSOL stress plot effect does not cooperate with PowerGraphics to give a plot with contour discontinuities. Before using the *VPUT temporary effect in plotting nodal stress (or other derived)ults, test the method carefully for errors, and for any errors in what I have just said! Warning: In a shell model, the plot of temporary *VPUT derived data may make the plot legend indicator for the TOP, MID or BOT surface of the shell elements meaningless -- annotate the plot to inform the reviewer.

e DESOL command does write derived information into the database to the nodes of elements, on a permanent basis. The command is powerful, and potentially dangerous. Annotate plots and change title s to inform the reviewer. It can be painfully slow to apply DESOL to every node of every element, element by element, in a large model.

63: How to Divide One Element Table Column by Another

divide one column of an element table (ETABLE) by another column, use the SEXP command. Make sure the denominator is nonzero! Per the commands manual, SEXP "forms an element table item by exponentiating and multiplying." The result of SEXP i s formed from (ABS(Lab1)**EXP1)*(ABS(Lab2)**EXP2). Because of the absolute value operations that protect ANSYS from complex numbers being generated, you will get the absolute value of the answeru want. To divide with SEXP, use a positive e xponent EXP1=+1 for the numerator Lab1, and a negative exponent EXP2=-1 for the denominator Lab2.

ou must have the ETABLE column answer with its positive or negative sign, one way to get i t would be to use a blend of SEXP and SMULT. Given ETABLE columns A and B, you want a column of A/B values with their signs. Use SMULT to form C=A*B which has the sa me sign as A/B. Use SEXP to form D=1/(ABS(B)**2) which is positive. Use SMULT to form E=C*D. Now the column E=A/B with it s correct sign.

64: Element Tables (ETABLE) and Array Data Exchange -- An Example

te that *VGET and *VPUT can communicate with an ETABLE and with an Array. In this way, information that can only be obtained in either an ETABLE or an Array can be moved back and forth for manipulation, evaluation, and display. You have to be inside /POST1 to use ETABLE. SOLVE has to have been executed in order for ETABLE data to be available. In brief testing, I found partial solve execution not to be sufficient t o make any data available for anment table, for example, element volume. In order to use *VPUT on an ETABLE, the array and ETABLE column will have to already exist. Create the ETABLE column by making a copy of an existing ETABLE column (you can use the SADD command, for example), or by creating a new dummy column from model information. Give the new column an appropriate name for the data that will come from the array. If selection of only a subset of your elements is ince, or if there are gaps in the element numbering, it may be preferable to use a *VMASK during the *VGET and *VPUT calls to avoid warning messages. The *VMASK array contents can be based on a test of element selection. Array size can be based on MIN and MAX values for selected element numbering, if you use an offset during data movement. Minimizing array size is a good reason for compressing node and element numbers when developing a largedel, before load cases, solutions and array dimensions are prepared.

example with shell elements: put shell element volume in an ETABLE, shell element area in an array, move the area array into an ETABLE column, divide volume by area to get shell element thickness for each element in a new ETABLE column, and do a colored ETABLE contour plot of your model's shell element thicknesses (do not average t he values in the ETABLE plot). If the shell element is of varying thickness, this process generates an average for thement. Print a colored picture of this plot. Augment this with an element plot using /ESHAPE,1 and coloring based on REAL constant values. This should help with "pesky visitors" who are always wondering how thick certain parts of a complex shell model are. It may help you catch some modeling errors. Here is a macro to generate the ETABLE thickness column and plot the model colored by element thickness. This macro is written to process Shell63 elements inselected set of e lements. It is a basic macro with no testing to prevent error conditions, or "cleanup" after execution. It illustrates movement of an array column into an element table column, use of masks, offset of the transferred data to minimize array and element table size, and division of one ETABLE column by another using the SEXP command. The macro has to be re-executed if the model is changed -- an ETABLE update would not be sufficient. Theominator that contains element area in the divide operation should automatically be nonzero because all shell elements have areas.

! ETABLE and Array usage and interaction example.! For illustration only. Use at your own risk.

! This example is used on SHELL63 elements.! An array is created called "aaa", element selection may be reduced,

! and element tables are used. A plot results.! Run from within /POST1

! Put element volume in an ETABLE, and element area in an array.! Move the area array data into the ETABLE

! Divide element volume by element area to get an element thickness column.

! Element thickness value should be the average for variable thickness elements.! Plot the ETABLE thickness data for a view of the Shell 63 elements

! that are contour colored according to the element thickness.!

esel,r,ename,,6 3 ! re-select only the SHELL63 elementsaaa= ! kill the array to be used

*get,xmax,elem, ,num,max ! what is the highest element number selected?! element number compression will be desirable

*get,xmin,elem, ,num,min ! minimum element number*dim,aaa,array, xmax-xmin+1 ! array to hold areas has to be this big*vget,aaa(1),el em,xmin,esel ! fill array with info on whether element is selected

! -1=not selected, 0=undefined, 1=selected! offset with xmin (see the manual)

*vmask,aaa(1) ! use element selection info as a mask*vget,aaa(1),el em,xmin,geom ! fill the array with geom info on the elements

! for shell elements this is AREA. Offset with xminetable,volu,vol u ! create element table column with element volumesadd,geom,volu, ,0,1 ! create dummy column to contain other data

*vmask,aaa(1) ! use array as a mask (geom data is positive or zero)*vput,aaa(1),el em,xmin,etab,geom ! put data into ETABLE "geom" column. Offset with xmin

sexp,thick,volu ,geom,1,-1 ! divide volume by area, get avg. shell element thick./title,ETABLE Plot of Shell 63 Element Thickness Values

pletab,thick,noav

u can then select a few elements of interest, and list the element table for the column containing the thickness, to get a numerical thickness value for those elements. You could use *VGET to put the REAL values for the shell elements into an array, and transfer that data into an ETABLE column. Then when you list ETABLE information for a selected element, you could see the REAL and the thickness value side-by-side. Contour colors could be explicitly assigned todifferent thicknesses found in the ETABLE column, if the number of thicknesses was not too great. You could place a button on the toolbar that calls a macro that (1) checks that the user is in /POST1, (2) checks that t here is results data in the database, (3) asks you to pick elements with the mouse, then (4) generates and prints the ETABLE values for the REAL, thickness, and stress values of those elements, and (5) finally cleans up and restores the original element

ection.

other use: Put shell element mid-plane Sx, Sy, and Sxy into columns, and multiply them by the element thickness column. The resulting data would be similar to TX, TY, and TXY data that can be obtained directly, but now would be in the direction defined by t he active coordinate system. A macro could (1) have the user pick nodes or keypoints to define a local coordinate system, (2) make it active, (3) develop this ETABLE data and generate plots colored by load-





-unit-length in the known directions, then (4) clean up. This could be done for SINT or SEQV if desired.

e possibilities are endless.

65: Error Estimation, PowerGraphics, and ERNORM

or Estimation will not be available when you enter /POST1 if PowerGraphics is active. If you turn off PowerGraphics, then the "Options for Output" in the GUI will offer the ERNORM setting that activates error estimation. If PowerGraphics is not active, then the "Options for Output" in the GUI will not offer the AVRES setting that controls discontinuity of contours at changes of material and REAL value for elements. The first time I encountered this was when Ildn't get an error report, and couldn't imagine why, until I had poked around for a while. I had entered /POST1 with /PowerGraphics active. ERNORM is ON by default when you enter /POST1, but only if PowerGraphics is OFF with /GRAPHICS,FULL.

66: Concatenate and Mesh Last

e of the things I have seen go wrong in model development is: I have concatenated lines and/or areas, t hen performed a boolean operation on them. Model problems resulted and I had to start from scratch (I re-ran most of the log file); I suggest that boolean operations happen first -- concatenate and mesh last. (This was with ANSYS 5.3; solid modeling problems are reduced with each version.)

ve found that when three or more areas are concatenated, the lines that are implicitly concatenated have to be concatenated manually before successful mapped meshing will proceed. When only two areas are concatenated, the lines concatenate automatically.

en concatenated areas are used to map mesh a volume, it may happen that an adjacent volume defined by an area that is part of the concatenated set will not mesh until the "pseudo-area" that results from the concatenation is deleted. I've had occasions when this did and did not happen. The concatenated li nes may need cleanup, also. It is possible that if the volumes that do not require concatenated areas in order to be meshed, are meshed first, that the remainingumes can have area and line concatenation created after, and then be meshed themselves, without error messages. This consideration may compromise easy mesh refinement and adaptive meshing. It may be necessary to go to tetrahedral elements for easy meshing, unless ANSYS revisions have fixed up mapped meshing concatenation.

via: I first encountered the word "contatenate" when using an IBM 370 a long time back. A neighbour told me that "concatenate" is based on the Latin word for "chain".

67: ANSYS Output of Data to Files for Use by Other Programs

merical data contained in parameters can be output into ASCII files using the *CFOPEN, the *VWRITE, and the *CFCLOS commands. The *VWRITE command only works when called from an input file that includes a format statement simil ar to FORTRAN. The following simple macro makes the *VWRITE command easy to use:

! Put this code into a macro file called "writer.mac"

! call with: writer,data! write data in arg1 to a file previously opened with *CFOPEN

! later on, close the file with *CFCLOSE*vwrite,arg1

(E16.8)

e following ANSYS /INPUT data test will demonstrate the use of the above macro. In this test, the macro has been called " writer.mac" and it is in the current directory. Either numbers or parameters that evaluate to numbers can be used in the following commands:

! Example of data output to file from ANSYS*cfopen,myoutput,dat

writer,123writer,234

/clearwriter,345

writer,456*cfclos

ecuting the above commands from within ANSYS generates the following data in the file "myoutput.dat", and demonstrates that the output file remains open in spite of the /CLEAR command. The following is the content of the file "myoutput.dat":

.12300000E+03

.23400000E+03

.34500000E+03

.45600000E+03

e filename used in the demo ended in ".dat" so that the data would be accessible to the MathCad program from MathSoft, Inc. The above procedure makes it possible to get ANSYS information out into another program without errors in manual transcription. If you can get the ANSYS information into a parameter, it can be moved to an external file. Data can be read back into ANSYS with the *VREAD command. Similar methods can be used to move arrays full ofa. Note that the *VGET and *VPUT commands can move data between element tables and arrays, and the arrays can be used to put data into external text files, so significant automated data movement is possible. This approach can help to reduce data errors in reports.

re is an example of temporarily switching the ANSYS /OUTPUT information from the default, to a file. Note that certain list information will not go to the file when the GUI is in use (read the manual).

! The following code switches /OUTPUT to a file,! writes two comments, writes PRSECT information on! linearized stresses along a previously defined path,

! then returns /OUTPUT to the default./output,lin_path,out

/COM,Linearized Path Results from PRSECT/COM,Compare Results with Code Allowables

PRSECT, ,0/output

s gives a permanent record that is independent of plotted results.

68: Writing Array Columns to Output or to Files

e *VWRITE command can be used to output an array column, in addition to sca lar parameters. The array position from which the printing will start must be indicated when executing the *VWRITE command. As mentioned above, the *VWRITE command cannot be executed inside the GUI, it has to be executed from an input file or macro. The *VWRITE command prints the data from the starting position on down to t he end of the column. The output that results cane-directed with the /OUTPUT or with the *CFOPEN and *CFCLOS commands. The following two macros can be used to make calling the *VWRITE command easy. The array must exist, having been created with a *DIM command. The first macro works on a 1-dimensional array parameter. Note the instruction on how to call the macro, with the array parameter name surrounded by single quotes in order to delay the evaluation.

! This macro will print a 1-dimensional array! according to the starting position indicated.

! If this macro is called WRITEAR1.MAC and an! array called COL1DATA is to be printed from

! position COL1DATA(1) to the end of the array! then call this macro with the statement:! WRITEAR1,'COL1DATA',1

! setting the name of the array in single quotes.! The user may wish to change the FORMAT statement.

*vwrite,arg1(arg2)

(E16.8)

e second works on a 2-dimensional array parameter. The macro call will include the row and column position from which to start. The *VWRITE statement will cause printing of a column of the 2-dimensional array. When calling the macro, the array parameter name is, as above, enclosed with single quotes to delay evaluation.

! This macro will print a column of a 2-dimensional array

! according to the starting position indicated.! If this macro is called WRITEAR2.MAC and an! array called MYDATA2D is to be printed from

! position MYDATA2D(1,2) to the end of column 2 then call! this macro with the statement:

! WRITEAR2,'MYDATA2D',1,2! setting the name of the array in single quotes.! The user may wish to change the FORMAT statement.

*vwrite,arg1(arg2,arg3)

(E16.8)

en that all ANSYS arrays are implicitly 3-dimensional, the second macro above could be used to print out a 1-dimensional array if the second calling parameter is set to one. A similar macro can be written to print a "column" of a 3-dimensional array. If a term in the array is MYARRAY(III,JJJ,KKK) then the *VWRITE command will cycle through the values of the III index when printing out data. The macro for a 3-dimensional array could be written so that it testsG2, ARG3, and ARG4 to see if they are zero. If they are zero, then they presumably were not entered, and the correct form of a *VWRITE command could be used to print a scalar, 1-D array, 2-D array, or 3-D array, as appropriate. Such a macro is illustrated below. Its use would be very error prone without error checking code. A scalar need not have its name enclosed in single quotes in calli ng this macro, but an array would have to be enclosed in single quotes as inabove examples. A user may want to customize this macro to change the FORMAT statements, or to remove the /NOPR and /GOPR commands.

! Macro to write a scalar or an array column, as appropriate.! Indicate the starting position for *VWRITE if an array is used.

! Enclose an array parameter name in single quotes. #################! Examples, if this macro is called WRITER.MAC:

! writer,aaa ! if aaa is a scalar! writer,'bbb',1,3 ,2 ! if bbb is a 3-D array parameter! Note the /NOPR and /GOPR commands. They will overwrite user settings.

/nopr ! reduce the amount printed to /OUTPUT

*if,arg2,ne,0,t hen ! if nonzero an array is used*if,arg3,eq,0,t hen ! if not a 2-D array

arg3=1

*endif*if,arg4,eq,0,t hen ! if not a 3-D array

arg4=1*endif*vwrite,arg1(arg2,arg3,arg4)

(E16.8)*else ! if a scalar

*vwrite,arg1(E16.8)

*endif/gopr ! switch on /OUTPUT

t these macros thoroughly before use. Note that they contain no error handling code. Warning: It is particularly difficult to remember to surround the name of the array parameter with single quotes.

69: Synthesizing Parameter Names and Manipulating Jobnames and Long Strings in APDL

hough I haven't found documentation reference to the following tricks, they work in ANSYS 5.3, and presumably will in future. The ability to synthesize parameter names, and to do other text manipulation, could lead to some very creative activities in "programming" ANSYS methods and in macro writing. Parameter names themselves can be synthesized by chaining text strings together. Remember that there is a limit on the number of parameters in a model -- arraysst be used to get around this, if it is a problem. Try these statements in ANSYS -- manually enter these lines one at a time in the ANSYS Input window, and check what turns up when the *STATUS command is issued (scroll down to the bottom of the STATUS text window that pops up):

aaa='qwer'

bbb='tyui'%aaa%%bbb%=12345*status

%aaa%1234=5*status

*do,iii,1,9$abc%iii%=iii$*enddo*status

what it's worth, you can even store ANSYS commands in parameters, and execute t hem. I encountered some trouble executing commands with commas embedded inside the character parameters, but the following worked. Give them a try:

aaa='nplo'%aaa%a='*get'

b='xx'c='active'

d='0'e='time'

f='wall'%a%,%b%,%c%,%d%,%e%,%f%

*status,%b%thetime=%b%/title,%a%,%b%,%c%,%d%,%e%,%f% yields %thetime%

/repl

ameters that hold text data are limited to 8 characters. Several text variables can be chained together (concatenated) using the "percent" sign. The user should experiment to see how blanks are truncated. The following example illustrates chaining. The strings are concatenated in the /TITLE command, and the /REPL command shows the result in the plot title.

xxx='The 1st'

yyy=' & 2nd'/TITLE,%xxx%%yyy%

/REPL

uations when this trick might be used could be to save and employ long title strings, annotation strings, or job names for the /FILNAME command. The method can use several parameters, or several terms of an array parameter. A jobname can be up to 32 characters long, so up to four parameters, or 4 terms in an array parameter, would be needed. Note t hat the *GET command can read in a jobname, with the *GET statement pointing to the character in the jobnameere the parameter will begin to read the string. An example of array use is:

*DIM,aaa,char,4

aaa(1)='First te'aaa(2)='rm & 2nd'

/TITLE,%aaa(1)%%aaa(2)%/repl

atabase could be saved with statements such as these, in which parameter "aaa" is text and "num" is an integer. The contents of "num" could be the results of a load step "num" and the file name would identify the load step number:

aaa='model'num='456'SAVE,%aaa%%num%,db

SAVE,%aaa%123,dbSAVE,myjob%num%,db

other use is with a parameter inside percent signs grouped with text with all inside single quotes. Consider this example, which was used to delete l oad step files in a complex application:

! Parameter "compname" contains the Jobname of a load step file*do,jjj,st1,st2,st3

*if,jjj,lt,10,then

/delete,compname,'s0%jjj%'*else

/delete,compname,'s%jjj%'*endif

*enddo

th the RESUME command and the /CLEAR command can destroy the counter used in a *DO loop. I have used the PARSAV command before RESUME, and the PARRES command immediately after, in order to recover the counter and other looping parameters when placing RESUME inside a *DO loop. The user should test this technique before using -- the parameters saved and restored may undesirably overwrite parameters in the file that is resumed. Look at/CLEAR example; it illustrates what can be done:

! test of looping

fini ! exit whatever is active*do,iii,1,3

parsav,all,xxx,parm/clear ! be prepared to hit OK button

parres,new,xxx,parm*enddo

ese methods can make it possible to program considerable automation into ANSYS, using the ability to assemble parameter names, parameter contents, commands, and file names from letters and numbers.

70: Solid Elements 95 and 92 -- Efficiency and Interconnection

ese two solid elements have mid-side nodes, so they follow curved surfaces nicely. Fewer elements are needed than with Solid45 8-node bricks, for equivalent accuracy. Note the ANSYS manual comments that the simpler flat-sided elements may be preferred for material nonlinearity. However, nonlinearity is supported by Solid92 and Solid95. The Solid45 tetrahedral element is "not recommended" in the ANSYS manuals because of it s low accuracy in predictingsses -- the higher order Solid92 and 95 tetrahedral option elements do not have these warnings, and may be preferred in some cases.

id element 95 is a 20-node brick element. It also supports a prism, pyramid, and tetrahedral element shape option. At revision 5.3 of ANSYS, my testing suggests that the prism and pyramid forms are not generated by the automatic volume mesher. At the 5.5 revision, pyramids may be generated by the mesher at the interface between the brick form, and the tetrahedral form. Brief testing I did suggests that meshing of volumes can successfully interface the brick andahedral forms. The tetrahedra formed at the interface with brick elements do not have mid-side nodes where they would not exist on the matching brick elements, so there should not be a big mismatch problem at the interface. These elements that have a mid-side node missing are considered to be degenerate forms in the ANSYS manuals, and are not recommended in regions with high stress gradients, or where exace stress values are important.

e Solid92 element is a 10 note tetrahedron -- it should act the same as the 10 node version of the Solid95 element in producing results. However, it executes significantly faster than the 10 node Solid95 element, presumably because the software is not dealing with the redundant extra 10 nodes. In large models, this speedup will be of value to users, so Solid92 elements should be considered where Solid95 tetrahedral forms would otherwise be employed in largectural models.

to Contents

urn to Main Page A and Optimization Introduction Page A Modeling Issues Page

98, 1999 byPeter C.Budgell -- You are welcome to print and photocopythese pages (don'tplagiarize or sell the contents).

y 27, 1999

E-mail Address: Please see my main page.

k to: The ANSYS® Home Page at www.ansys.comk to: ANSYS Technical Overview Recommended Reading

more links, Return to Links on Main Page.


Documents

Ansys R11 Tips