Upload
mochamad-bhadawi
View
21
Download
0
Embed Size (px)
DESCRIPTION
List of Codes & Standards
Citation preview
15 Pune Mumbai Road, Sai Chambers, Wakdewadi Pune - 411003 Contact No. - +91-020-66414000
TECHNICAL BID FOR 1 x 6.5MW(Net) POWER PLANT
AT (INDONESIA)) POWER DIVISION
Project Name Proposal No. Revision No. Date Sect Page No.
ACE PROJECT E-0110 0 20-03-2015 Annex-II Page 1 of 25
ANNEXURE-II LIST OF CODES AND STANDARDS
Sr. No.
Codes/Norm (International standards)
Description Codes/Norms/ Standard
(as practiced by Thermax Ltd.)
1. Relevant Indian Standards For structural steelwork design IS:800
2.
Design & Environmental Guidelines required by International Finance
Corporation (IFC), World Bank Group,
Washington , D.C., U.S.A.
World Bank Norms (2008 version) (referred only as
guideline)
3. Industry Standards For terminal blocks IEC 60947-7-1
4. AGMA 2001, B88 For gearing AGMA 6011 I03
5. API 650/ASME Diesel Fuel Storage Tank SAME OR IS 803
6. Relevant ASME Codes For emergency boiler feed systems Relevant ASME Codes
7. Relevant ASME Codes To calculate total head of boiler feed
pumps Relevant ASME Codes
8. Relevant ASME Codes For emergency feed pump system &
to calculate total head
9. OSHA's standard For silencers provided for the
superheater safety valve & start up vent valve
OSHA's standard
15 Pune Mumbai Road, Sai Chambers, Wakdewadi Pune - 411003 Contact No. - +91-020-66414000
TECHNICAL BID FOR 1 x 6.5MW(Net) POWER PLANT
AT (INDONESIA)) POWER DIVISION
Project Name Proposal No. Revision No. Date Sect Page No.
ACE PROJECT E-0110 0 20-03-2015 Annex-II Page 2 of 25
Sr. No.
Codes/Norm (International standards)
Description Codes/Norms/ Standard
(as practiced by Thermax Ltd.)
10. Indian Standards For gallery and stairway equipment Indian Standards
11. OSHA's standard Silencer to reduce relief valve noise. OSHA's standard
12.
American Boiler Manufacturer's Association (ABMA/BS. 2486 for a
boiler operating at 48 kg/cm2 a/430 deg C (668 PSIG/806 deg F)
For quality of boiler feed water IS 10392, BS 2486
13. API 650/ASME For boiler feed water storage tank. HEI & ASME VIII
14. American Crane Manufacturers
Association For Electric Operated Overhead
Travelling Bridge Crane IS:3177
15. API 650/ASME For clarified water storage tank IS 803
16. ASME Code Vessel for air receiver ASME VIII, IS:7938/2825
17. ASME B31.3 ASME B31.1
For piping fabrication, installation, inspection & testing
ASME B31.3 ASME B31.1
18. AWS Regulations, ASME B31.3 For welding procedures AS PER IBR OR ASME 31.1
19. AWS & Section IX of the ASME Boiler
and Pressure Vessel Code Welder's qualifications
AWS & Section IX of the ASME Boiler and Pressure
Vessel Code
20. ANSI B31.3 Pipe fabrication required for piping
work ANSI B31.3
15 Pune Mumbai Road, Sai Chambers, Wakdewadi Pune - 411003 Contact No. - +91-020-66414000
TECHNICAL BID FOR 1 x 6.5MW(Net) POWER PLANT
AT (INDONESIA)) POWER DIVISION
Project Name Proposal No. Revision No. Date Sect Page No.
ACE PROJECT E-0110 0 20-03-2015 Annex-II Page 3 of 25
Sr. No.
Codes/Norm (International standards)
Description Codes/Norms/ Standard
(as practiced by Thermax Ltd.)
21. ASME B31.3 Flange ratings and facings, bolts,
and gaskets B 16.5
22. EJMA 4th Edition Tolerances for dents & scratches EJMA 4th Edition
23. ASME B31.3 Bevelled ends for butt welded joints ASME B31.3 & B31.3
24. ASME B31.3 Branch connections ASME B31.3 & B31.3
25. ANSI B2 Threaded connections ANSI B2
26. OSHA regulation Field routed piping Relevant IS Code
27. Intergranular Corrosion test specified
in Section 12 of ASTM A 240 Relevant IS Code
28. ASTM A 380 Descaling and cleaning of entire
assembly ASTM A 380
29. ASME B31.3 Code for Pressure Piping For welded connections ASME B31.1 Code for POWER PIPING
30. ASME B31.3 for carbon steel piping PWHT is to be performed IBR & ASME B31.1
31. Code for Pressure Piping ASME
B31.3,"Chemical Plant and Petroleum
Refinery Piping"
For radiography if required IBR & ASME B31.1
15 Pune Mumbai Road, Sai Chambers, Wakdewadi Pune - 411003 Contact No. - +91-020-66414000
TECHNICAL BID FOR 1 x 6.5MW(Net) POWER PLANT
AT (INDONESIA)) POWER DIVISION
Project Name Proposal No. Revision No. Date Sect Page No.
ACE PROJECT E-0110 0 20-03-2015 Annex-II Page 4 of 25
Sr. No.
Codes/Norm (International standards)
Description Codes/Norms/ Standard
(as practiced by Thermax Ltd.)
32. ANSI B31.3 or ANSI B31.1 Weldment Inspection IBR & ASME B31.1
33. ASME B31.3 Relevant Post-weld procedures IBR & ASME B31.2
34. ASTM C 552 For insulation IS 14164 / 8183 / 4671
35. ASTM D1557 (Modified Proctor) Soil density tests IS 2720
36. ACI 214 - Recommended Practice for Evaluation of Strength Test Results of
Concrete Cast-in-place Concrete IS:516-1959
37. ACI 301 - Specifications for Structural
Concrete for Buildings Cast-in-place Concrete IS 456:2000
38. ACI 302.1 - Guide for Concrete Floor
and Slab Construction Cast-in-place Concrete IS 2571 : 1970
39. ACI 304 - Guide for Measuring, Mixing,
Transporting and Placing Concrete Cast-in-place Concrete IS 6461 : 1973
40. ACI 305 - Hot Weather Concreting Cast-in-place Concrete IS 7861 (Part-1)
41. ACI 306 - Cold Weather Concreting Cast-in-place Concrete IS 7861 (Part-2)
42. ACI 308 - Standard Practice for Curing
Concrete Cast-in-place Concrete IS 6461 : 1973
15 Pune Mumbai Road, Sai Chambers, Wakdewadi Pune - 411003 Contact No. - +91-020-66414000
TECHNICAL BID FOR 1 x 6.5MW(Net) POWER PLANT
AT (INDONESIA)) POWER DIVISION
Project Name Proposal No. Revision No. Date Sect Page No.
ACE PROJECT E-0110 0 20-03-2015 Annex-II Page 5 of 25
Sr. No.
Codes/Norm (International standards)
Description Codes/Norms/ Standard
(as practiced by Thermax Ltd.)
43. ACI 309 - Guide for Consolidation of
Concrete Cast-in-place Concrete IS 7246: 1974
44. ACI 318 - Building Code Requirements
for Structural Concrete Cast-in-place Concrete IS 456:2000
45. ASTM C31 - Standard Practice for Making and Curing Concrete Test
Specimens in the Field Cast-in-place Concrete IS 6461 : 1973
46. ASTM C33 - Standard Specification for
Concrete Aggregates Cast-in-place Concrete IS 383:1970
47. ASTM C39 - Standard Test Method for Compressive Strength of Cylindrical
Concrete Specimens Cast-in-place Concrete IS 516:1959
48. ASTM C94 - Standard Specimen for
Ready-Mixed Concrete Cast-in-place Concrete IS 4926 : 2003
49. ASTM C138 - Standard Test Method for
Unit Weight, Yield, and Air Content (Gravimetric) of Concrete
Cast-in-place Concrete IS 516:1959
50. ASTM C143 - Standard Test Method for
Slump of Hydraulic Cement Concrete Cast-in-place Concrete IS 4031: 1996
51. ASTM C150 - Standard Specification
for Portland Cement Cast-in-place Concrete IS 8112
52. ASTM C172 - Standard Practice for Sampling Freshly Mixed Concrete
Cast-in-place Concrete IS 1199:1959
53. ASTM C173 - Standard Test Method for Air Content of Freshly Mixed Concrete
by the Volumetric Method Cast-in-place Concrete IS 7325 : 1974
15 Pune Mumbai Road, Sai Chambers, Wakdewadi Pune - 411003 Contact No. - +91-020-66414000
TECHNICAL BID FOR 1 x 6.5MW(Net) POWER PLANT
AT (INDONESIA)) POWER DIVISION
Project Name Proposal No. Revision No. Date Sect Page No.
ACE PROJECT E-0110 0 20-03-2015 Annex-II Page 6 of 25
Sr. No.
Codes/Norm (International standards)
Description Codes/Norms/ Standard
(as practiced by Thermax Ltd.)
54. ASTM C230 - Standard Specification
for Flow Table or Use in Tests of Hydraulic Cement
Cast-in-place Concrete IS 4031 : 1996
55.
ASTM C260 - Standard Specification
for Air-Entraining Admixtures for Concrete
Cast-in-place Concrete IS 9103 : 1999
56. ASTM C494 - Standard Specification for Chemical Admixtures for Concrete
Cast-in-place Concrete IS 9103 : 1999
57.
ASTM C618 - Standard Specification for Fly Ash and Raw or Calcined
Natural Pozzolan for Use as a Mineral
Admixture in Portland Cement Concrete
Cast-in-place Concrete
Relevant Indian standard code 58.
ASTM E1155 - Standard Test Method for Determining Floor Flatness and
Levelness Using the F-Number System Cast-in-place Concrete
59.
ASTM C1315 - Standard Specification
for Liquid Membrane-Forming Compounds Having Special Properties
for Curing and Sealing Concrete
Cast-in-place Concrete
60. ACI 318, Chapter 5 Concrete mix design proportions IS: 10262
61. ASTM Relevant Indian standard code
62. ASTM C150, Type I Portland Cement IS 8112
15 Pune Mumbai Road, Sai Chambers, Wakdewadi Pune - 411003 Contact No. - +91-020-66414000
TECHNICAL BID FOR 1 x 6.5MW(Net) POWER PLANT
AT (INDONESIA)) POWER DIVISION
Project Name Proposal No. Revision No. Date Sect Page No.
ACE PROJECT E-0110 0 20-03-2015 Annex-II Page 7 of 25
Sr. No.
Codes/Norm (International standards)
Description Codes/Norms/ Standard
(as practiced by Thermax Ltd.)
63. ASTM C33 Fine aggregate & Coarse aggregate of
gravel or crushed stone IS 383:1970
64. ACI 318 Size coarse aggregate IS 456:2000
65. ACI 318 Water IS 6461 : 1973
66. ASTM C260 Air Entraining Agent IS 6461 : 1973
67. ASTM C494 High-range water reducer IS 6461 : 1973
68. ASTM C1315 Curing Compound IS 6461 : 1973
69. ASTM C618 Fly ash IS 6461 : 1973
70. ASTM C494 Accelerators IS 6461 : 1973
71. ASTM C494 Retarders IS 6461 : 1973
72. ACI 302 Placing of floors and slabs IS 2571 : 1970
73. ACI 301, ACI 304 and ACI 318 IS 456:2000
74. ACI 301 and ACI 309 IS 456:2000
15 Pune Mumbai Road, Sai Chambers, Wakdewadi Pune - 411003 Contact No. - +91-020-66414000
TECHNICAL BID FOR 1 x 6.5MW(Net) POWER PLANT
AT (INDONESIA)) POWER DIVISION
Project Name Proposal No. Revision No. Date Sect Page No.
ACE PROJECT E-0110 0 20-03-2015 Annex-II Page 8 of 25
Sr. No.
Codes/Norm (International standards)
Description Codes/Norms/ Standard
(as practiced by Thermax Ltd.)
75. ACI 308 Curing of Concrete IS 6461 : 1973
76. ACI 306 and ACI 308 Curing in cold weather IS 6461 : 1973
77. ACI 301 Finishing of Concrete IS 456:2000
78. ACI 306 Cold weather concreting IS 7861 : Part 2 : 1975
79. ACI 305 Hot weather concreting IS 7861 : Part 1 : 1975
80.
ASTM Specifications D-2241 and D-
1784 with SDR of 26 NSF Approved
AWWA C-900 standards
PVC Pipes IS 4985 : 2000
81.
AWWA C906
ASTM D3350 cell classification of 345434C
HDPE Pipe IS 4984 : 1995
82. AWWA Specifications Standard C-500
AWWA Standards for potable water use Valves As per relevant standards
83. AWWA Standard C-110 Fittings As per relevant standards
84. USA Department of Transportation
Specifications Road & Swale grading Indian road congress (IRC)
85. AASHO-T180 (modified Proctor) Backfill IS 2720
15 Pune Mumbai Road, Sai Chambers, Wakdewadi Pune - 411003 Contact No. - +91-020-66414000
TECHNICAL BID FOR 1 x 6.5MW(Net) POWER PLANT
AT (INDONESIA)) POWER DIVISION
Project Name Proposal No. Revision No. Date Sect Page No.
ACE PROJECT E-0110 0 20-03-2015 Annex-II Page 9 of 25
Sr. No.
Codes/Norm (International standards)
Description Codes/Norms/ Standard
(as practiced by Thermax Ltd.)
86. ASTM Specification No. D-3034 Pipes and fittings As per relevant standards
87. ASTM Specification C-12 Crushed Rock IS 383:1970
88. ASTM Specifications C-14 and C-478 Material of manholes IS 12592 : 2002, IS 1726 : 1991
89. U.S. Foundry No. 604-Au-ORS, traffic
bearing Covers for manholes IS 12592 : 2002, IS 1726 : 1991
90. ASTM Specifications C-14 and C-478 Wet well Relevant Indian standard code
91. ASTM Specification A-20 GI Pipe IS 4736
92. AWWA Standard C-500 Gate Valve As per relevant standards
93. ASTM Class 60 Steel casing IS 2062
94. ACI 117 - Standard Specifications for Tolerances for Concrete Construction
and Materials Concrete Formwork IS 456:2000
95. ACI 301 - Specifications for Structural
Concrete for Buildings Concrete Formwork
IS 456:2000
96. ACI 318 - Building Code Requirements
for Structural Concrete Concrete Formwork
15 Pune Mumbai Road, Sai Chambers, Wakdewadi Pune - 411003 Contact No. - +91-020-66414000
TECHNICAL BID FOR 1 x 6.5MW(Net) POWER PLANT
AT (INDONESIA)) POWER DIVISION
Project Name Proposal No. Revision No. Date Sect Page No.
ACE PROJECT E-0110 0 20-03-2015 Annex-II Page 10 of 25
Sr. No.
Codes/Norm (International standards)
Description Codes/Norms/ Standard
(as practiced by Thermax Ltd.)
97. ACI 347 - Recommended Practice for
Concrete Formwork Concrete Formwork IS 6461 : Part 5 : 1972
98.
ASTM D1751 - Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Non-extruding and
Resilient Bituminous Types)
Concrete Formwork IS 1838 : Part 1 : 1983
99.
ASTM E154 - Standard Test Methods for Water Vapor Retarders used in contact with earth under concrete
slabs, on walls, or as Ground Cover
Concrete Formwork Relevant Indian standard code
100. ACI 117, ACI 301, ACI 318 and ACI
347 Design of Formwork
IS 456:2000, IS 6461 : Part 5 : 1972
101. ACI 301 and ACI 347 Design of Formwork
102. ACI 117 - Standard Specifications for Tolerances for Concrete Construction
and Materials
Concrete Reinforcement IS 456:2000
103. ACI 301 - Specifications for Structural
Concrete for Buildings Concrete Reinforcement IS 456:2000
104. ACI 315 - Details and Detailing of
Concrete Reinforcement Concrete Reinforcement SP-34
105. ACI 318 - Building Code Requirements
for Structural Concrete Concrete Reinforcement IS 456:2000
106. ASTM A185 - Standard Specification
for Steel Welded Wire Fabric, Plain, for Concrete Reinforcement
Concrete Reinforcement IS 1566:1982
15 Pune Mumbai Road, Sai Chambers, Wakdewadi Pune - 411003 Contact No. - +91-020-66414000
TECHNICAL BID FOR 1 x 6.5MW(Net) POWER PLANT
AT (INDONESIA)) POWER DIVISION
Project Name Proposal No. Revision No. Date Sect Page No.
ACE PROJECT E-0110 0 20-03-2015 Annex-II Page 11 of 25
Sr. No.
Codes/Norm (International standards)
Description Codes/Norms/ Standard
(as practiced by Thermax Ltd.)
107. ASTM A615 - Standard Specification for Deformed and Plain Billet-Steel Bars for Concrete Reinforcements
Concrete Reinforcement IS 1786: 1985
108.
ASTM A706 - Standard Specification
for Low-Alloy Steel Deformed Bars for Concrete Reinforcements
Concrete Reinforcement Relevant IS code
109.
AWS D12.1 - Recommended Practices for Welding Reinforcement Steel Metal Inserts, and Connections in Reinforced
Concrete Construction.
Concrete Reinforcement
IS 2751:1979
110. AWS D1.4 - Structural Weld Code -
Reinforcing Steel Concrete Reinforcement
111. CRSI - Manual of Practice, and
Documents 63 and 65 Concrete Reinforcement IS 12461:1988 & IS 11370:1985
112.
U.S.Army Corps of Engineers
Specification CRD C621 - Specification for Non-Shrink Grout
Non Shrink Grout Relevant Indian standard code
113. ASTM C109 - Standard Test Method for
Compressive Strength of Hydraulic
Cement Mortars
Non Shrink Grout IS 4031 : 1988
114. AISC - Code of Standard Practice for
Steel Buildings and Bridges Structural Steel Requirements IS 800 / IS 1915
115.
AISC - Load and Resistance Factor
Design (LRFD) Specification for Structural Steel Buildings
Structural Steel Requirements IS 800
116. AISC - Specifications of Structural
Joints using ASTM A325 or A490 Bolts
approved by the Research Council in
Structural Steel Requirements IS 800 / IS 4000
15 Pune Mumbai Road, Sai Chambers, Wakdewadi Pune - 411003 Contact No. - +91-020-66414000
TECHNICAL BID FOR 1 x 6.5MW(Net) POWER PLANT
AT (INDONESIA)) POWER DIVISION
Project Name Proposal No. Revision No. Date Sect Page No.
ACE PROJECT E-0110 0 20-03-2015 Annex-II Page 12 of 25
Sr. No.
Codes/Norm (International standards)
Description Codes/Norms/ Standard
(as practiced by Thermax Ltd.)
Structural Connections
117. AWS D1.1 - Structural Welding Code Structural Steel Requirements IS 816 / IS 1323
118. AWS A5.1 - Specification for Carbon Steel Electrodes for Shield Metal Arc
Welding Structural Steel Requirements
As per reputed approved manufacturer's standard or relevant IS Standard
119. AWS A5.5 - Specifications for Low-Alloy Steel Covered Arc Welding Electrodes
Structural Steel Requirements
As per reputed approved manufacturer's standard or relevant IS Standard
120. AWS A5.17 - Specification of Carbon
Steel Electrodes and Fluxes for Submerged Arc Welding
Structural Steel Requirements
121. AWS A5.20 - Specification for Carbon Steel Electrodes for Flux Cored Arc
Welding
Structural Steel Requirements
122. SSPC - Steel Structures Painting
Manual Structural Steel Requirements
As per Thermax's Standard Painting Specifications
for Export Projects
123. ASTM A36 - Standard Specification for
Structural Steel Structural Steel Requirements IS 2062
124.
ASTM A123 - Standard Specification
for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products)
Structural Steel Requirements IS 4759
125. ASTM A153 - Standard Specification
for Zinc Coating (Hot-Dip) on Iron and Steel Hardware
Structural Steel Requirements IS 4736
126. ASTM A780 - Standard Practice for Repair of Damaged and Uncoated
Structural Steel Requirements IS 4737
15 Pune Mumbai Road, Sai Chambers, Wakdewadi Pune - 411003 Contact No. - +91-020-66414000
TECHNICAL BID FOR 1 x 6.5MW(Net) POWER PLANT
AT (INDONESIA)) POWER DIVISION
Project Name Proposal No. Revision No. Date Sect Page No.
ACE PROJECT E-0110 0 20-03-2015 Annex-II Page 13 of 25
Sr. No.
Codes/Norm (International standards)
Description Codes/Norms/ Standard
(as practiced by Thermax Ltd.)
Areas of Hot-Dip Galvanized Coatings
127. ASTM A307 - Standard Specification
for Carbon Steel Bolts and Studs, 60,000 PSI Tensile Strength
Structural Steel Requirements HT BOLTS - B7/2HIS 1367
128.
ASTM A325 - Standard Specification for Structural Bolts, Heat Treated,
120/105 KSI Minimum Tensile Strength
Structural Steel Requirements IS 800 / IS 4000
129. ASTM A490 - Standard Specification
for Heat-Treated Steel Structural Bolts,
150 KSI Minimum Tensile Strength
Structural Steel Requirements IS 800 / IS 4000
130.
ASTM A500 - Standard Specification for Cold-Formed Welded and Seamless Carbon Steel Tubings in Rounds and
Shapes
Structural Steel Requirements IS 1239 / 3589
131.
ASTM A501 - Standard Specification
for Hot-Formed Welded and Seamless Carbon Steel Structural Tubing
Structural Steel Requirements Relevant IS Code
132. ASTM A992 - Standard Specification for Steel and Structural Shapes For
Use in Building Framing
Structural Steel Requirements SP6 / IS 2062
133. ASTM F436 - Standard Specification
for Hardened Steel Washers Structural Steel Requirements Relevant IS Code
134. ASTM F844 - Standard Specification
for Washers, Steel, Plain (Flat), Unhardened for General Use
Structural Steel Requirements B 16.20
15 Pune Mumbai Road, Sai Chambers, Wakdewadi Pune - 411003 Contact No. - +91-020-66414000
TECHNICAL BID FOR 1 x 6.5MW(Net) POWER PLANT
AT (INDONESIA)) POWER DIVISION
Project Name Proposal No. Revision No. Date Sect Page No.
ACE PROJECT E-0110 0 20-03-2015 Annex-II Page 14 of 25
Sr. No.
Codes/Norm (International standards)
Description Codes/Norms/ Standard
(as practiced by Thermax Ltd.)
135.
American Institute of Steel Construction (AISC) Quality
Certification Program for Conventional Steel Buildings (Sbd)
Fabricator's qualifications Relevant IS Code
136. AWS Certified Welding Inspectors Fabricator's qualifications IBR
137. ASTM B633 Adhesive Anchors Relevant IS Code
138. ASTM B695 Galvanizing IS4736
139. NEC Articles 501 and 502 IS 1913, IS 8224.
140. IEC Codes Electrical Construction
IS 12943, IS 2148, IS8309, IS3043, IS9537, IS3837, IS2667, IS3419, IS3480, IS6946, IS4649, IS1293,
IS3070. 141.
AFBMA Anti-Friction Bearing Manufacturers Association
Electrical Construction
142. ANSI American National Standards
Institute Electrical Construction
143. ASME American Society of Mechanical
Engineers Electrical Construction
IS 12943, IS 2148, IS8309, IS3043, IS9537, IS3837, IS2667, IS3419, IS3480, IS6946, IS4649, IS1293,
IS3070.
144. ASTM American Society for Testing and
Materials Electrical Construction
145. FM Factory Mutual Electrical Construction
15 Pune Mumbai Road, Sai Chambers, Wakdewadi Pune - 411003 Contact No. - +91-020-66414000
TECHNICAL BID FOR 1 x 6.5MW(Net) POWER PLANT
AT (INDONESIA)) POWER DIVISION
Project Name Proposal No. Revision No. Date Sect Page No.
ACE PROJECT E-0110 0 20-03-2015 Annex-II Page 15 of 25
Sr. No.
Codes/Norm (International standards)
Description Codes/Norms/ Standard
(as practiced by Thermax Ltd.)
146. ICEA Insulated Cable Engineers
Association Electrical Construction
147. ICS Institute for Industrial Controls
and Enclosures Electrical Construction
IS 12943, IS 2148, IS8309, IS3043, IS9537, IS3837, IS2667, IS3419, IS3480, IS6946, IS4649, IS1293,
IS3070.
148. ISA Instrument Society of America Electrical Construction
149. IEEE Institute of Electrical and
Electronic Engineers Electrical Construction
150. IES Illuminating Engineering Society of
North America Electrical Construction
151. MG 1 Standard Publications for Motors
and Generators Electrical Construction
IS 12943, IS 2148, IS8309, IS3043, IS9537, IS3837, IS2667, IS3419, IS3480, IS6946, IS4649, IS1293,
IS3070. 152. NEC National Electrical Code Electrical Construction
153. NEMA National Electrical
Manufacturers Association Electrical Construction
154. OSHA Occupational Safety and Health
Administration Electrical Construction
IS 12943, IS 2148, IS8309, IS3043, IS9537, IS3837, IS2667, IS3419, IS3480, IS6946, IS4649, IS1293,
IS3070.
155. National Electrical Safety Code (NESC) Electrical Construction OSHA
156. API RP 500 Section 14 and NFPA 497 Electrical area classification drawing Not applicable for Power plant area as it is safe area.
15 Pune Mumbai Road, Sai Chambers, Wakdewadi Pune - 411003 Contact No. - +91-020-66414000
TECHNICAL BID FOR 1 x 6.5MW(Net) POWER PLANT
AT (INDONESIA)) POWER DIVISION
Project Name Proposal No. Revision No. Date Sect Page No.
ACE PROJECT E-0110 0 20-03-2015 Annex-II Page 16 of 25
Sr. No.
Codes/Norm (International standards)
Description Codes/Norms/ Standard
(as practiced by Thermax Ltd.)
157. NEC Article 392 For cable tray system IS 9537, IS3837, IS2667
158. IEC Codes and Standards or NEMA VE
2 and Aluminium Association's Specifications
Material of cable trays IS 9537, IS3837, IS2667
159. IEC Codes and Standards or NEMA FG
1 and UL 568 For fiberglass cable trays Not applicable.
160. ICEA Codes and Standards For all wires and cables IS: 7098, IS: 1554, IS10810.
161. ICEA S-66-524 and UL 1569 For 600 V multiple conductor power
wiring Indian Electricity Act, Electricity supply Act, Indian
Electricity Rules.
162. NEC Article 310 For 600 V single conductor power
and control wiring IS 694
163. NEMA WC 70 For multi conductor cable IS: 7098, IS: 1554, IS10810.
164. ANSI MC 96.1 For single pair thermocouple
extension cable ANSI MC 96.1
165. ASA/ISA Color coding of conductors IS: 7098, IS: 1554, IS10810.
166. NEC Article 100 For medium voltage power cables IS: 7098, IS: 1554, IS10810.
167. NEC Article 344, 501 or 502 Conduit systems for medium voltage
power cables IS 9537,IS3837,IS2667
15 Pune Mumbai Road, Sai Chambers, Wakdewadi Pune - 411003 Contact No. - +91-020-66414000
TECHNICAL BID FOR 1 x 6.5MW(Net) POWER PLANT
AT (INDONESIA)) POWER DIVISION
Project Name Proposal No. Revision No. Date Sect Page No.
ACE PROJECT E-0110 0 20-03-2015 Annex-II Page 17 of 25
Sr. No.
Codes/Norm (International standards)
Description Codes/Norms/ Standard
(as practiced by Thermax Ltd.)
168. ICEA S-68-516 and UL 1072 Material for multiconductor 15 kV
power cable IS 7098
169. AEIC CS6 For Insulated conductors IS: 8130
170. ASTM B-496 and UL 1072 For grounding conductor IS 3043
171. IEEE 576 For installing, terminating and
testing cables IS: 10810
172. NFPA Codes and Standards For emergency and egress lighting IS 9583
173. NEMA 12 and NEMA 4X For pull boxes and junction boxes IS 3837, IS 2667.
174.
ANSI/NEMA Std. Pub. No. FB 1, "Fittings and Supports for Conduit and
Cable Assemblies" and National Electrical Contractor's Association's
"Standard of Installation" and UL
Compliance
For anchors, fasteners, hangers, supports and equipment mounting
IS 3837, IS 2667.
175. NEC/IEC For substation grounding IEEE 80-2000
176. IEEE 80-2000 Grounding of outdoor 66 kV open
bus substation section IEEE 80-2000
177. NFPA 780 and UL 96 Common ground bonding with Lightning Protection System
IS 2309.
15 Pune Mumbai Road, Sai Chambers, Wakdewadi Pune - 411003 Contact No. - +91-020-66414000
TECHNICAL BID FOR 1 x 6.5MW(Net) POWER PLANT
AT (INDONESIA)) POWER DIVISION
Project Name Proposal No. Revision No. Date Sect Page No.
ACE PROJECT E-0110 0 20-03-2015 Annex-II Page 18 of 25
Sr. No.
Codes/Norm (International standards)
Description Codes/Norms/ Standard
(as practiced by Thermax Ltd.)
178. ANSI C57, IEC, IEEE and NEMA Codes
and Standards For Power Transformers IS:2026 (Part I-IV)
179. ANSI C57 For Total losses and overload capacity and noise levels of
Transformers IEC: 85
180. NEMA MG-1 For motors in MCC IS: 325
181. IEC1131-3 For Graphical User Interface IEC1131-3
182. ISA-S5.4 - 1989 For loop wiring diagrams ISA-S5.4 - 1989
183. NFPA 85 Standard for Boiler and
Combustion Systems Hazards Code For safety trips and burner
management NFPA 85 Standard for Boiler and Combustion
Systems Hazards Code
184. IEC 100 (Electromagnetic Compatibility
Standard)* Instrumentation Specifications
Vendor Specific, Shall be confirmed during detail engineering stage
185. IEC1131-3 (Confirmation Software
Standard) Instrumentation Specifications IEC1131-3 (Confirmation Software Standard)
186. ISA S88 (Batch Software Standard) Instrumentation Specifications ISA S88 (Batch Software Standard)
187. ISA Instrumentation Specifications ISA
188. IEC60068-2-1* IEC60068-2-2*
IEC 60068-2-14*
Temperature Test, Quality Requirements
Vendor Specific, Shall be confirmed during detail engineering stage
15 Pune Mumbai Road, Sai Chambers, Wakdewadi Pune - 411003 Contact No. - +91-020-66414000
TECHNICAL BID FOR 1 x 6.5MW(Net) POWER PLANT
AT (INDONESIA)) POWER DIVISION
Project Name Proposal No. Revision No. Date Sect Page No.
ACE PROJECT E-0110 0 20-03-2015 Annex-II Page 19 of 25
Sr. No.
Codes/Norm (International standards)
Description Codes/Norms/ Standard
(as practiced by Thermax Ltd.)
189. IEC 60068-2-30* Humidity Test, Quality Requirements Vendor Specific, Shall be confirmed during detail
engineering stage 190. IEC 60068-2-6* Vibration Test, Quality Requirements
191. IEC 60068-2-27* Shock Test, Quality Requirements
Vendor Specific, Shall be confirmed during detail
engineering stage
192. CISPR 11: Group 1, Class A* Emissions Test, Quality
Requirements
193. IEC 60068-4-2* ESD Immunity Test, Quality
Requirements
194. IEC 60068-4-3* Radiated RF Immunity Test, Quality
Requirements
195. IEC 60068-4-4* EFT/B Immunity Test, Quality
Requirements
196. IEC 60068-4-5* Surge Transient Immunity Test,
Quality Requirements Vendor Specific, Shall be confirmed during detail
engineering stage 197. IEC 60068-4-6*
Conducted RF Immunity Test,
Quality Requirements
198. Not Mentioned Instrument and apparatus for
temperature measurement ASME PTC 19.3 (1974)
199. Not Mentioned Temperature Measurement -
Thermocouples ANSI - MC 96.1 - 1982
200. Not Mentioned Temperature Measurement by
electrical resistance thermometers IS: 2806
15 Pune Mumbai Road, Sai Chambers, Wakdewadi Pune - 411003 Contact No. - +91-020-66414000
TECHNICAL BID FOR 1 x 6.5MW(Net) POWER PLANT
AT (INDONESIA)) POWER DIVISION
Project Name Proposal No. Revision No. Date Sect Page No.
ACE PROJECT E-0110 0 20-03-2015 Annex-II Page 20 of 25
Sr. No.
Codes/Norm (International standards)
Description Codes/Norms/ Standard
(as practiced by Thermax Ltd.)
201. Not Mentioned Thermometer-element-Platinum
resistance IS: 2848 / DIN 43760
202. Not Mentioned Instrument and apparatus for
pressure measurement ASME PTC 19.2 (1964)
203. Not Mentioned Bourdon tube pressure and vacuum
gauges IS: 3624/1996
204. Not Mentioned Instruments and apparatus for flow
measurement ASME PTC 19.5 (1972) Interim supplement, Part-II
205. Not Mentioned Measurements of fluid flow in closed
conduit ISO-5167
206. Not Mentioned
Safety requirements for electrical
and electronic measuring and controlling instrumentation
ANSI C 39.5 / 1974
207. Not Mentioned Compatibility of analog signals for
electronic industrial process
instruments
ISA-S 50.1: ANSI MC 12.1 / 1975
208. Not Mentioned Dynamic response testing of process
control instrumentation ANSI MC 4.1 (1975) - ISA -S26 (1968)
209. Not Mentioned Surge withstand capability (SWC)
tests ANSI C 37.90A (1989), IEC-255.4
210. Not Mentioned Printed circuit boards IPC TM-650, IEC 326C
211. Not Mentioned General requirements and tests for
printed wiring boards IS-7405 (Part-I)/1973
15 Pune Mumbai Road, Sai Chambers, Wakdewadi Pune - 411003 Contact No. - +91-020-66414000
TECHNICAL BID FOR 1 x 6.5MW(Net) POWER PLANT
AT (INDONESIA)) POWER DIVISION
Project Name Proposal No. Revision No. Date Sect Page No.
ACE PROJECT E-0110 0 20-03-2015 Annex-II Page 21 of 25
Sr. No.
Codes/Norm (International standards)
Description Codes/Norms/ Standard
(as practiced by Thermax Ltd.)
212. Not Mentioned Edge socket connectors IEC 130-11
213. Not Mentioned Requirements and methods of testing
of wire wrap terminations DIN 41611 Part-2
214. Not Mentioned Dimensions of attachment plugs and
receptacles ANSI C73-1973.(Supplement ANSI C73a 1980)
215. Not Mentioned Contact Rating - AC services NEMA ICS Part-2 125, A-600
216. Not Mentioned Contact Rating - DC services NEMA ICS Part-2 125, N-600
217. Not Mentioned Types of enclosures IS 13947 (Part I) 1993
218. Not Mentioned Racks, panels and associated
equipment EIA: RS-310-C-1983 (ANSI C83.9 - 1972)
219. Not Mentioned Classification of degree of protection
provided by enclosure IEC 529
220. Not Mentioned Classification of hazardous area NEMA Article 500, Volume-6, 1978
221. Not Mentioned Electrical Instruments in hazardous
dust locations ISA-RP 12.11
222. Not Mentioned Intrinsically safe apparatus NFPA Article 493 Volume-4 1978
223. Not Mentioned Purged and pressurized enclosure for
electrical equipment in hazardous NFPA Article 496 Volume-4, 1978
15 Pune Mumbai Road, Sai Chambers, Wakdewadi Pune - 411003 Contact No. - +91-020-66414000
TECHNICAL BID FOR 1 x 6.5MW(Net) POWER PLANT
AT (INDONESIA)) POWER DIVISION
Project Name Proposal No. Revision No. Date Sect Page No.
ACE PROJECT E-0110 0 20-03-2015 Annex-II Page 22 of 25
Sr. No.
Codes/Norm (International standards)
Description Codes/Norms/ Standard
(as practiced by Thermax Ltd.)
location
224. Not Mentioned Stainless Steel material of tubing and valves, for sampling system
ASTM A 269-79 GRTO-316
225. Not Mentioned Submerged helical coil heat
exchangers for sample coolers ASTM D11-98
226. Not Mentioned Specifications and guides for the use
of general-purpose annunciators ISA RP 18.1
227. Not Mentioned Surge withstand capability tests for
Anunciators ANSI C37.90 a -1971 and IEEE Standard 472-1974
228. Not Mentioned Relays and relay system associated
with electric power apparatus IEEE Standards 3.13
229. Not Mentioned Surge withstand capability tests for
Interlocks & Protections ANSI C37.90 a - 1971 and IEEE Standard 472-
1974
230. Not Mentioned
General requirements and tests for switching devices for control and
auxiliary circuits including contactor
relays
IS-6875 (Part-I)/1973
231. Not Mentioned Turbine water damage prevention ASME-TDP-1-1980
232. Not Mentioned Boiler safety interlocks NFPA Section 85B, 85D, 85E, 85F, 85G
233. Not Mentioned Practice and requirements for semi-
conductor power rectifiers ANSI C34.2
15 Pune Mumbai Road, Sai Chambers, Wakdewadi Pune - 411003 Contact No. - +91-020-66414000
TECHNICAL BID FOR 1 x 6.5MW(Net) POWER PLANT
AT (INDONESIA)) POWER DIVISION
Project Name Proposal No. Revision No. Date Sect Page No.
ACE PROJECT E-0110 0 20-03-2015 Annex-II Page 23 of 25
Sr. No.
Codes/Norm (International standards)
Description Codes/Norms/ Standard
(as practiced by Thermax Ltd.)
234. Not Mentioned Surge withstand capability tests for
UPS ANSI C 70.90 A/1971, IEC-255.4
235. Not Mentioned Recommended practice for sizing
large VRLA batteries for generating stations and sub-stations
IEEE-485
236. Not Mentioned Flow equation for Sizing Control
Valve ISA-S39.2 / 1972
237. Not Mentioned Control Valve seat leakage ANSI / FCI 70.2
238. Not Mentioned Face to face dimensions of Control
Valves ANSI B16.10, ISA S75.03 & ISA S75.16
239. Not Mentioned Steel pipe, Flanges and flanged
fittings ANSI B16.5
240. Not Mentioned Steel valves, flanges and Butt weld
ends ANSI B16.34
241. Not Mentioned Control Valve Capacity Test
Procedure ISA S75.02
242. Not Mentioned Seamless Carbon Steel Pipe for
Instrument Tubing ASTM-A-106
243. Not Mentioned Material for socket weld fittings ASTM-A-105
244. Not Mentioned Dimensions of fittings ANSI-B16.11
15 Pune Mumbai Road, Sai Chambers, Wakdewadi Pune - 411003 Contact No. - +91-020-66414000
TECHNICAL BID FOR 1 x 6.5MW(Net) POWER PLANT
AT (INDONESIA)) POWER DIVISION
Project Name Proposal No. Revision No. Date Sect Page No.
ACE PROJECT E-0110 0 20-03-2015 Annex-II Page 24 of 25
Sr. No.
Codes/Norm (International standards)
Description Codes/Norms/ Standard
(as practiced by Thermax Ltd.)
245. Not Mentioned Code for pressure piping, welding,
hydrostatic testing ANSI-B 31.1
246. Not Mentioned Nomenclature for instrument tube
fittings ISA-RP 42.1 / 1982
247. Not Mentioned Seamless Stainless Steel Tubes for
Instrument Tubing ASTM A-312 TP 304
248. Not Mentioned Alloy Steel Pipe for Instrument
Tubing ASTM A 335 Gr P22
249. Not Mentioned Thermocouple extension wires /
cables ANSI MC96.1
250. Not Mentioned Color-coding of single or multi-pair
cables IPCEA S-61-402
251. Not Mentioned Guide for design and installation of cable system in power generating
station (insulation, jacket materials)
IEEE Standard 422
252. Not Mentioned Requirements of vertical tray flame
test IEEE 383
253. Not Mentioned Standard specification for tinned soft or annealed copper wire for electrical
purpose ASTM B33
254. Not Mentioned
Guide for the design and installation of cable system in power generating
station (cable trays, support systems, conduits)
IEEE Standard 422, NEMA VE-1, NEC-1981. Test Standards NEMA VE-1-1979
255. Not Mentioned Galvanizing of carbon steel cable
trays ASTM A-386
15 Pune Mumbai Road, Sai Chambers, Wakdewadi Pune - 411003 Contact No. - +91-020-66414000
TECHNICAL BID FOR 1 x 6.5MW(Net) POWER PLANT
AT (INDONESIA)) POWER DIVISION
Project Name Proposal No. Revision No. Date Sect Page No.
ACE PROJECT E-0110 0 20-03-2015 Annex-II Page 25 of 25
Sr. No.
Codes/Norm (International standards)
Description Codes/Norms/ Standard
(as practiced by Thermax Ltd.)
256. Not Mentioned Mono-mode fiber ITU-T G.652
*Note: Adherence/Compliance of these codes is vendor specific, shall be confirmed during detailed engineering stage.