Upload
conor-puckett
View
23
Download
1
Tags:
Embed Size (px)
DESCRIPTION
Research paper on clean water initiatives for the future.
Citation preview
Water Shortage Relief: Analyzing New Chemically Driven Processes for Desalination
by
Julie Perez
Conor Puckett
Submitted to
Professor Moore
and
Mark Provence
ME 333T
Fall 2013
1
Executive Summary
Water shortage is a large scale issue that the news, organizations, and other media have
played up in recent years. Unfortunately, it is as dangerous a problem as explained by these
outlets, if not more so. Jonathan Chenoweth from the New Zealand Scientist reports that
“According to the UN World Water Assessment Programme, by 2050, 7 billion people in 60
countries may have to cope with water scarcity” (Chenoweth, 2008, url). This critical point
looms near in our future, and the effects of severe water shortages can be observed and are
already felt today all around the world.
Currently, reverse osmosis (RO) water desalination is the primary way to “harvest” fresh
water from saturated salt water sources to be able to provide drinkable water. Reverse osmosis
requires a large amount of energy, time, and capital to run and maintain facilities. Forward
osmosis (FO) and electrochemically mediated saltwater desalination (EMSD) chips are two
unique solutions to these and other problems discussed in the paper.
Three criteria for investigation include production potential, efficiency, and cost. When
comparing the existing RO process with FO and EMSD, the researched technologies may apply
to large or small scale uses, respectively. Currently, as both the FO and EMSD systems exist in
research and development phases, comparing the final output in terms of overall production
capabilities is difficult to determine. Scientific tests are the primary grounds for production
potential claims. Both show signs of efficient desalination, ranging from 25% to 85%, but still
leave room for improvement. And though the initial costs for both are higher, investors are likely
to save in energy expenses.
2
Both FO and EMSD have great potential to grow into the forefront of water desalination
techniques. Needing a stable energy infrastructure, FO is poised to replace RO in large,
economically stable areas such as Coastal Australia, India, and the Mediterranean. EMSD chips
are unique among all other desalination techniques in being small enough to work as a personal
unit while retaining the ability to combine with other chips to function for villages, cities, etc.
There is still a large amount of headway that can be made through investment in research,
especially with the EMSD chips. The company or companies that fund the research will be
known as facilitators of freshwater for the world, and will essentially play a major role in ending
the problem of water scarcity that these solutions seek to address.
3
Introduction
Global freshwater sources are currently unable to sustain the world population because
existing techniques fail to meet the demands for clean drinking water. However, new technology
shows the potential to supply drinkable water to those who need it most. Presently used to treat
saltwater, Reverse Osmosis (RO) forces water through a semi-permeable membrane which
allows the smaller water molecules to pass though while the larger contaminants are held on the
other side ("How reverse osmosis," 2013, url). Forward Osmosis (FO), similar to RO, utilizes
two liquids of different concentrations to create a pressure difference across a semi-permeable
membrane with “low or no hydraulic pressures” introduced (Cath, Childress & Elimelech, 2006).
Electrochemically Mediated Seawater Desalination (EMSD) uses a microchip to support a
branched channel system where an induced electric field allows partially desalinated water to
travel through one channel and the concentrated salt solution to flow down the second channel
(R. Crooks, personal communication, November 12, 2013). Both of these technologies improve
upon RO techniques by reducing associated costs or necessary energy requirements in order to
produce clean water in a more efficient and cost effective way.
This white paper analyzes two potential solutions to the global water crisis: forward
osmosis desalination plants and electrochemical desalination microchips. After discussing the
present issues surrounding water availability and the pitfalls to reverse osmosis desalination
techniques, we will describe the two new technologies in greater detail. We will then compare
these two technologies across important criteria of evaluation in order to present an accurate
picture of where each technology stands with regards to their respective implementation. Finally,
we present our own recommendations on how to proceed with these developments in order to
prevent future water shortages from plaguing our global community.
4
Statement of the Problem
Water scarcity is rapidly becoming an alarming issue. Access to fresh, clean drinking
water is limited in developing countries. The severity of this shortage can be seen through its
effects, including chronic illnesses, devastated local economies, and even death. In the past
decade, a study by the World Health Organization estimates Diarrhea contributes to nearly nine
million annual deaths of children under the age of 5, with a major factor being the consumption
of contaminated water (Alexander, 2013, p 13). This shows that access to clean water is an
integral part of maintain the health and safety of communities across the globe.
In the United States, growing population densities have created an unmet demand for
clean water. According to a journalist for the Saturday Evening Post, “Of the 47 states that
responded to a U.S. General Accounting Office, 36 states predicted shortages by 2013 under
normal conditions, 46 under drought conditions” (Yeoman, 2013, url). Factors such as
population growth, unbalanced economic distribution, and the effects of climate change all
reduce the usable freshwater in circulation. Water shortage has become a looming problem on a
global scale. To sustain itself, the public needs improved water purification techniques that will
allow for the treatment of current water sources that are not possible to drink.
Innovation has been halted in the past for a multitude of reasons. Though it is a well-
known fact that developing countries are economically depressed, research shows water scarcity
keeps them at this state. For example, pertaining to India’s water crisis, “Extremely poor
management, unclear laws, government corruption, and industrial and human waste have caused
a water supply crunch and rendered what water is available practically useless due to the huge
quantity of pollution” (Mehta, 2012, url). Because these countries lack the government setup or
5
economic capital to regulate water usage, clean water supplies have all but disappeared in many
areas. Analysts predict this depletion rate of fresh water may affect a staggering portion of the
global population. Scientific journalist Jonathon Chenoweth from New Scientist magazine
reported that, “According to the UN World Water Assessment Programme, by 2050, 7 billion
people in 60 countries may have to cope with water scarcity” (Chenoweth, 2008, url). The scope
of water scarcity, as we can see, is certainly not solely a problem of dense, urban centers or that
of developing communities. It is a problem present across the world.
In addition to economic strife, government involvement and lax regulations have helped
cause the water scarcity problem that we face today. In nations like the United States, when
water levels get to drought conditions, water restrictions are typically put in place. However,
many homeowners circumvent this law by drilling their own wells to tap directly in to
groundwater beneath their property, not understanding their action’s effect on the current water
table. Sarah Courts, a well owner in Atlanta, defends herself and other well owners stating that
“We’re not draining Lake Lanier here” (Abkowitz, 2008). Evidence however shows conflicting
points. Georgia’s state geologist, Jim Kennedy, says that these wells “can lower the amount of
groundwater if there are a lot of wells in one area… [and] can actually cause land to sink”
(Abkowitz, 2008). Elsewhere, residents such as Jason Cooper from North Carolina are appalled
“that people would circumvent water restrictions in order to keep their lawns green” (Abkowitz,
2008). Issues like this prompt the submission of bills before state legislators urging for the same
restrictions to be placed on private wells, but because of the backlash from drilling companies
and wealthy residents, the issue of private wells was removed from further government
consideration (Abkowitz, 2008). Without a strong government influence, many public water
tables could be severely depleted if private drilling is left unchecked. This unchecked private
6
drilling causes the available amount of water to decrease as a whole, perpetuates the problem
rather than alleviating it, and “could [even] deplete or dry up a creek” (Abkowitz, 2008).
New innovations into freshwater solutions are integral to the continued providing of a
global source of clean water. Without clean water, developing nations will continue to struggle to
overcome economic hardships. The health of these nations will also continue to suffer as we
have seen without access to fresh water. We will investigate cutting edge techniques to solve this
global water shortage.
Global Water Shortage Solutions
Before researching potential solutions, this section will give an overview of clean water
production, both in a general sense of the operation and in the effectiveness of current, factory
driven procedures utilizing reverse osmosis techniques. We will focus on two types of
technological advancements and discuss their functionality in reducing the amount of salt present
in water sources.
Conventional Technology
Desalination plants make up a good portion of the current technology associated with
large scale water filtration. That being said, they also have large draw backs that must be
evaluated before implementation of a system. Currently, most plants work under Reverse
osmosis (RO), Multi-Stage Flash (MSF), Electro-dialysis (ED) or some combination of RO and a
thermal process (Kim, Park & Yeh, 2013). The crux of RO desalination techniques lies in
membranes within the filtration housing. Published in the Journal of Membrane Science, Tzahi
Cath explains the methodology of RO, stating that “RO uses hydraulic pressure to oppose, and
exceed, the pressure of the saltwater in order to produce purified water by forcing the aqueous
7
feed through a membrane” (Cath, Childress & Elimelech, 2006). This, however, has a large
energy cost associated with production. Many of the areas that lack the most amount of clean
water do not have the economic or electrical power to support the “old-style” of RO desalination
plants (Chaudhary, 2013;Scott, 2013; Yeoman, 2013). A further analysis of cost will be
presented later.
Proposed Innovations
New technologies and paradigm shifts have caused a large potential for lessening the
current costs of desalination processes. Forward Osmosis (FO) techniques are rendering a more
efficient way to process seawater. The Electrochemically Mediated Seawater Desalination
(EMSD) process removes the need for a semi-permeable membrane and simplifies the
desalination procedure.
Large scale solution: forward osmosis. Professor Menachem Elimelech of Yale’s Mason
Laboratory states that “[t]he main advantages of using FO are that it operates at low or no
hydraulic pressures…” (Elimelech, 2007). Without the expense of maintaining hydraulic
pressures as in RO, the cost to run the facility will
decrease. The FO process is described to the right
with Figure 1 showing the different components to
the system. A concentrated solution called a draw
solution causes the water to move from the salt
water, across the semi-permeable membrane and
into the draw solution (Cath, Childress & Elimelech,
2006). A draw solution containing dissolved
8
Figure 1- Schematic of Forward Osmosis Process (Elimelech, 2007)
ammonia and carbon dioxide gases effectively extract water from the salt water solution. From
the draw solution, applied thermal energy causes the ammonia and carbon dioxide to return to
their gaseous state, allowing for “efficient and complete removal and reuse” of the draw solution
components (Elimelech, 2007). This process takes place in a separate storage tank from the
holding draw solution. As the draw solution is heated and the solutes are removed, the fresh
water is piped to its own storage tank and is now free of both salt and the draw solution
components. The leftover brine solution is piped away and disposed (Cath, Childress &
Elimelech, 2006).
Small scale solution: electrochemically mediated seawater desalination. In contrast to
FO, the EDMS microchip operates at a microscopic level and incorporates a low power voltage
source instead of a semi-permeable membrane to drive desalination. The EDMS process is
demonstrated to the right in Figure 2. Scientific journalist Alex Scott from Chemical and
Engineering News explains, “as water is forced through two channels, which are electrically
connected through a bipolar electrode, the electrode creates an electric field that forces positive
ions into a branching channel, and the resulting charge imbalance forces negative ions to
follow”(Scott, 2013, url). The University of
Texas provides a more detailed chemical
interpretation: “An embedded electrode
neutralizes some of the chloride ions in
seawater to create an ‘ion depletion zone’ that
increases the local electric field compared
with the rest of the channel. This change in
the electric field is sufficient to redirect salts”
9
Figure 2. EMSD Microchip Operational Diagram (Scott, 2013).
(“Chemists work to,” 2013, url). The output has water flowing through the branch taking up
dissolved salt while the water continuing through the main channel is partially desalinated.
Cost Benefit Analysis
Established criteria for evaluation include production potential, efficiency, and monetary
expenses. We present the topics in a ranked order of significance. Because the two methods are
new concepts, with the EMSD chip barely at prototyping stages, we focused on the potentials
associated with each for future consumption. Declaration of the production potential is crucial as
it establishes the differences in the intended applications for each technology and compares them
with current production capabilities. The next key point was the desalination efficiency of each
device. Finally, we considered the ease of which each technology could be implemented by
determining the monetary costs.
Production Potential
Forward osmosis is a good desalination technique in that it can be applied in a variety of
intake sources including both brackish water and seawater. For countries, like Australia, that
have an infrastructure capable of supporting a desalination plant, a forward osmosis plant would
be a beneficial addition rather than continuing to create plants using reverse osmosis or thermal
techniques ("Perth seawater desalination," 2012,url). India’s government set aside roughly $18
billion for water projects in the hopes of attracting private groups to come up with the most
effective way to provide clean water (Chaudhary , 2013,url). Such support from the national
governments would allow for a larger interest in constructing cost effective, efficient
desalination facilities utilizing forward osmosis.
10
Currently, forward osmosis has only been tested in a scaled environment. Yale professor
Menachem Elimelech states that “[t]he most important measure to be taken in order to advance
the field of forward osmosis is the development of new membranes” (Elimelech, 2007). Another
pivotal aspect of forward osmosis that can be improved upon is the composition of the draw
solution. It has been determined that using ammonium bicarbonate as a solute allowed for the
most cost-efficient process as it “required no electricity, thereby drastically reducing the cost per
ton of product water” (Kim, 2013). Should the membranes and draw solutions be scaled up,
forward osmosis systems have the ability to improve and reach a production scale comparable to
that of RO systems today. Currently the “average capacity and corresponding cost for [RO] was
6000m3/day and .70$/m3 (Karagiannis & Soldatos, 2007).
Considering EMSD technology, in order for the microchip to operate in the developing
countries or water stressed communities which require its assistance the most, the chip must
filter enough water to meet average consumption rates. The prototype of the microchip is
depicted in Figure 3 to better understand the scale
of its process. The research team, consisting of
Knust, Hlushkour, Anand, Tallarek, and Crooks,
clarifies that the device’s design only allows water
to flow through two micro-channels, each at a
diameter of about 22 µm (Knust et al., 2013,url).
At micro-channels comparable to the size of a
human hair, “operating a single micro-
desalination unit at a time produces 40 nano-liters of desalted water per minute. To prove
practicality for global usage, the chip requires the development of faster flow rates, on the order
11
Figure 3- Microchip Prototype (“Chemists work to,” 2013)
of liters per day” (Knust et. al., 2013, url). Developers admit that adjusting the scale of achieved
desalinated water in a timely manner challenges the potential of a singular chip. According to
Morgan Anderson, Project Manager for Okeanos Technologies which helps sponsor the research,
“Right now, we are trying to build a unit capable of integrating 20,000 to channel larger
quantities of water for practical applications” (M. Anderson, personal communication,
November 12, 2013). Parallel arrangements of many micro-channel systems should allow for
increased water flow rates for varying applications.
While sponsoring companies debate over which communities the EMSD product should be
distributed to, researchers take a particular interest in two particular regions of the globe.
Countries within the Middle East and water stressed coastal regions in the U.S. can provide the
components to power this simple chip and benefit from its portability (R. Crooks, personal
communication, November 12, 2013). The amount of people each unit can sustain remains
uncertain at this early stage of development. Crooks states the long run goal, saying, “We are
running simulations to test methods which improve the water quality and increase volumetric
output of the device. We want the microchip to produce enough water for individual and
household usage” (R. Crooks, personal communication, November 12, 2013). Unlike reverse
osmosis and forward osmosis, the electrochemically mediated seawater desalination technology
gives an innovative perspective on future desalination methods by offering its users the
convenience of personal usage.
12
Efficiency
As it stands now, forward osmosis is very close to having the same recovery amount as
standard desalination techniques. Elimelech states that within the last 6 years “Lab tests show an
effective 85% recovery from a sea water source…[and] the capability of FO to produce very
high recoveries is unmatched by existing desalination techniques” (Elimelech, 2007). This high
recovery is due, in part, to some of the slightly different components from that of RO. The
membranes used in FO techniques allow for a higher water transport as well as a larger salt
rejection (Mamisaheby, Phuntsho, Shon, Lotfi & Kim, 2012). This allows for FO plants to keep
more of the salt solution out of the freshwater making the membranes a key part in retaining a
higher efficiency than current processes.
If forward osmosis is used as the desalination process, “approximately 24-45% of the
thermal energy needed by multi-effect distillation (MED)” (Elimelech, 2007) will be used and
only about “21% of the electrical consumption of MED or 9% of the reverse osmosis techniques
is required” (Elimelech, 2007). This allows the thermal energy costs to remain closer to that of
steam condensers in current electrical power plants (Elimelech, 2007). Due to the efficiencies
described above, it requires less energy for the forward osmosis process to function because it
can work at lower temperatures than reverse osmosis processes. This allows for the operating
cost to actually be less than that of a typical reverse osmosis style plant.
Each solution must present proof of effective desalination to support our initial claim,
which considers optimized desalination techniques as the solution to drinking water shortages.
For the EMSD chip, Crooks explains, “To date, this electrochemically mediated desalination
provides up to 25% desalination. Health standards require drinking water to be at 99%
13
desalination” (R.Crooks, personal communication, November 12, 2013). He reveals that a newer
model within the simulation stage of prototyping “adds a secondary voltage source, which can
reach upwards of 50% desalination” (personal communication, November 12, 2013). However,
according to Kyle Knust, the graduate student in the research team at the University of Texas
who is accredited for inventing the EMSD chip, creating the chip in the first place “was proof of
principle” (“Chemists work to,” 2013, url). Knust continues, “We’ve made comparable
performance improvements while developing other applications based on the formation of an ion
depletion zone, suggesting that 99 percent desalination is not beyond our reach” (“Chemists
work to,” 2013, url). Though the device is not yet able to perform to the necessary standards for
implementation, scientists remain optimistic on finding ways to improve the process to meet
demands.
Though previously mentioned aspects, such as processing time and desalination
percentage, require modifications, one key characteristic does not. The EMSD chip reduces
energy costs, intriguing most researchers. As large energy storage and generation run
desalination plants, the microchip requires nothing more than a single, standard variety, store-
bought battery with an output of 3 Volts to function. The only preceding step before desalination
is to remove sand and sediment by letting the grains settle naturally, with no further treatment,
chemical additives, or energy applications (“Chemists work to,” 2013, url). This breakthrough
therefore establishes notable energy efficiency through a low battery power input, making it an
ideal alternative to current methods as far as energy is concerned.
14
Monetary Cost/Ease of Implementation
In bringing desalination facilities to places in need of water, a major factor is economic
cost. Tae-woo Kim from the Korea Advanced Institute of Science and Technology comments on
the economic cost posed by desalination facilities, “Construction costs are the largest portion of
the capital costs, ranging between 50-85%”(Kim, 2008). These construction costs can cripple a
project before it is able to launch and develop. If the project is given a green light, there are still
maintenance costs to consider, as well the energy costs to run the plant. One of the biggest
drawbacks with any mode of desalination plant is that in poor, rural communities, there is simply
not enough capital nor existing energy infrastructure in place to currently support a desalination
plant (Kim, 2008; Mehta, 2012).
As we saw earlier, the feasibility of implementation is quite good. In countries where the
infrastructure can support an updated desalination plant, government funding seems to be
available for private companies (Chaudhary , 2013, url). This allows for a sense of competition
that can drive the initial cost down as companies compete to receive the funding. Finally, the
longevity of forward osmosis seems to be guaranteed with huge potential for growth and
development. With companies vying for the ability to create the new plants, a need to research
even more efficient membranes and draw solutions will be created. In the future, these new
advances could lead to the potential for declining operating costs.
In starting at a microscopic scale and working up to both personalized and large scale
usage, EMSD allows for a range of price options. To evaluate the cost, we must understand the
investment and the potential profits long run successes bring. From Anderson’s experience with
Okeanos Technologis, he comments that only one fifth of total costs come from acquiring the
15
water supply, adding that the remaining operational cost for the EMSD chip, thought above RO
at the moment, will in the long run pay for themselves through the energy saved (M. Anderson,
personal communication, November 12, 2013). With the primary focus of aiding water stressed
regions, Richard Crooks voices the scope of savings associated with this research.
“Seawater desalination is one way to address this need, but most current
methods for desalinating water rely on expensive and easily contaminated
membranes. The membrane-free method we’ve developed still
needs to be refined and scaled up, but if we can succeed at that, then one day it
might be possible to provide fresh water on a massive scale using a simple,
even portable, system” (“Chemists work to,” 2013, url).
Although no dollar amount has been tagged to the technology, researchers aim for an overall
price that will be less than current desalination factories.
Recommendations
The fresh water shortage we are currently facing is a global problem that will require
many solutions in order to truly be remedied. We believe forward osmosis desalination to be at
the forefront of those solutions, followed by the encouraging developments achieved through
electrochemically mediated seawater desalination. Because FO plants would only be possible in
large countries with stable infrastructure, the FO plants would be focused on providing fresh
water to the densely populated coastal areas in countries like Australia, India, and nations in the
Mediterranean region. Poorer countries, as well as inland locations without groundwater,
generally do not benefit from this new form of desalination. In light of all the previously
presented information, we believe forward osmosis desalination to be a good solution towards
16
mitigating current water shortages in some densely populated regions around the globe. We
recommend that further research be done into making for effective draw solutions that will
require less energy to maintain. In addition to draw solutions, more effective membranes will
also allow for a cheaper desalination facility in the long run. That being said, we also recognize
the need for more comprehensive solutions for developing nations and those areas away from the
sea and without adequate amounts of groundwater.
For communities where desalination facilities are not a feasible option, including those
lacking the infrastructure to support them, electrochemically mediated seawater desalination
techniques provide for a practical alternative for producing clean water. Because the design of
the EMSD chip only requires the addition of a common variety battery source, coastal regions of
both the U.S. and developing countries are likely to carry the minimal resources needed for its
usage (“Chemists work to,” 2013, url). Similar to forward osmosis plants, the location of salt
water sources restricts the desalination application to these areas. After researching the creation
of the EMSD chip, we conclude that further development is necessary. Before the technology
can be distributed for public usage, the percentage of desalination must match that of safe
drinking levels. Additionally, the product needs to operate at a faster flow rate to produce the
volumetric output required to sustain its target audience. Overall, we commend this innovative
approach of a portable, individual water desalination system as it holds a promising future.
17
Bibliography
1. (2013). Chemists work to desalt the ocean for drinking water, one nanoliter at a
time. The University of Texas at Austin News. Retrieved from
http://www.utexas.edu/news/2013/06/27/chemists-work-to-desalt-the-ocean-for-
drinking-water-one-nanoliter-at-a-time/
2. (2013) How reverse osmosis works. Water Quality Association. Retrieved from
http://www.wqa.org/sitelogic.cfm?ID=872
3. Abkowitz, A. (2008, July 31). There's Water In Them There Hills. Wall Street Journal -
Eastern Edition. pp. D1-D2. Retrieved from
http://online.wsj.com/news/articles/SB121745840551198655
4. Alexander , K. A., & Blackburn, J. K. (2013). Overcoming barriers in evaluating diarrhea
disease in resource poor settings: assessment of recurrent outbreaks in Chobe District,
Botswana . BMC Public Health, 13(1), 1-15. Retrieved from
http://www.biomedcentral.com/1471-2458/13/775
5. Anderson, Morgan. (2013, November 12). Personal Interview.
6. Cath, T., Childress, A., & Elimelech, M. (2006). Forward osmosis: Principles,
applications and recent developments. The Journal of Membrane Science, 1-18.
Retrieved from www.sciencedirect.com
7. Chaudhary, A. (2013, October 30). India’s essar eye’s water projects. Desalination Plants.
Retrieved from http://www.bloomberg.com/news/2013-10-31/india-s-essar-eyes-water-
projects-desalination-plants.html
8. Chenoweth, J. (2008). Water, water everywhere. (Cover story). New Scientist,
199(2670), 28-32. Retrieved from https://studentportalen.uu.se/uusp-filearea-
18
tool/download.action?nodeId=107684&toolAttachmentId=46623.
9. Crooks, Richard. (2013, November 12). Personal Interview.
10. Elimelech, M. (2007, January). Yale constructs forward osmosis desalination pilot plant.
Membrane Technology, 7-8. Retrieved from
http://www.yale.edu/env/elimelech/News_Page/files/membrane_technology_jan2007.pdf
11. Karagiannis, I., & Soldatos, P. (2007). (2008). Water desalination cost literature: review and
assessment. Science Direct, 223(1-3), 448–456. Retrieved from
http://www.sciencedirect.com/science/article/pii/S0011916407008843
12. Kim, T., Park, S., & Yeh, K. (2013). (2013). Cost-effective design of a draw solution
recovery process for forward osmosis desalination. Science Direct, 327, 46-51. Retrieved
from http://www.sciencedirect.com/science/article/pii/S0011916413003512
13. Knust, K., Hlushkou, D., Anand, R., Tallarek, U., & Crooks, R. (2013). Electronically
mediated seawater desalination. Angewandte Chemie International Edition, 52(31), 8107-
8110. Retrieved from http://phys.org/news/2013-06-sea-electrochemically-seawater-
desalination-microfluidic.html
14. Mamisaheby, S. M., Phuntsho, S. P., Shon, H. S., Lotfi, F. L., & Kim, J. K. (2012).
Assessing the major factors affecting the performances of forward osmosis and its
implications on the desalination process. Chemical Engineering Journal, 231, 481-496.
Retrieved from http://www.sciencedirect.com/science/article/pii/S1385894713009650
15. Mehta, P. (2012). Impending water crisis in India and comparing clean water standards
among developing and developed nations. Archives Of Applied Science Research,
4(1), 497-507. Retrieved from
http://www.academia.edu/2034987/Impending_water_crisis_in_India_and_comparing_cl
19
ean_water_standards_among_developing_and_developed_nations_Archives_of_Applied
_Science_Research
16. Scott, A. (2013, July 22). Running dry. Chemical & Engineering News, 91(29), 10-15.
Retrieved from http://cen.acs.org/articles/91/i29/Running-Dry.html
17. Yeoman, B. (2013, July 1). The Looming Water Crisis. Saturday Evening Post, 1-2.
Retrieved October 17, 2013, from NewsBank on-line database (Access World News)
20