AN11130 - Ampleon...Table 1. Summary of bias con [1] Resistor values may have to be changed for part of range. [2] Dependent upon PCB layout. troller characteristics Drain voltage

AN11130Bias module for 50 V GaN demonstration boardsRev. 2 — 1 September 2015 Application note

Document informationInfo ContentKeywords GaN, biasAbstract This application note describes a bias controller module for GaN HEMT

RF power transistors. It provides constant quiescent drain current with temperature, special bias and power sequencing, and overcurrent protection.

AN11130Bias module for 50 V GaN demonstration boards

Revision historyRev Date Description

v.2 20150901 Modifications • The format of this document has been redesigned to comply with the new identity

guidelines of Ampleon.• Legal texts have been adapted to the new company name where appropriate.

v.1 20111208 Initial version

AN11130#2 All information provided in this document is subject to legal disclaimers. © Ampleon The Netherlands B.V. 2015. All rights reserved.

Application note Rev. 2 — 1 September 2015 2 of 14

Contact informationFor more information, please visit: http://www.ampleon.comFor sales office addresses, please visit: http://www.ampleon.com/sales


1. Introduction

GaN HEMT RF power transistors require temperature-compensated gate bias voltages, similar to LDMOS devices, to maintain constant quiescent drain currents with temperature. They are depletion mode devices requiring special bias and power sequencing compared to LDMOS devices. This application note describes a bias controller module which provides these functions, and overcurrent protection.

2. Bias sequencing

The most important consideration for DC with GaN HEMTs, is the bias sequencing. There are two issues to consider:

• Never apply drain voltage when the gate is at 0 V, as the device draws excessive drain current. Thus, any GaN bias controller must include sequenced drain voltage switching.

• For a given VGS, GaN HEMTs are likely to be potentially unstable at lower VDS. Therefore, decrease the gate voltage to below the pinch-off voltage VP (such as 3 V) while the drain voltage is being turned on and off.

Figure 1 illustrates recommended power-up and power-down sequences for the drain and gate voltages.

(1) The typical discharge time shown is for illustration only, and is not intended as a recommendation. It is important that VGS is held at a voltage of less than VP until VDS is less than approximately 10 V.

Fig 1. Gate and drain voltage sequence

0 10 20 0 10 20 30 40 50−6

−4

−2

0

time (ms)

VG VD0

20

40

60

dischargethroughpowersupply

aaa-001666




3. Gate current

Because the GaN HEMT gate terminal is a Schottky diode, bias generators must provide significant amounts of both positive and negative gate current:

• GaN HEMTs have higher gate leakage currents than comparable LDMOS devices. The negative gate current can be as high as 500 A/mm of gate periphery at elevated junction temperatures; the gate current evaluates to 5 mA for a 100 W device operating at 200 C junction temperature.

• When the device is driven into saturation, rectified positive gate current flows into the gate diode. At heavy RF compression, this gate current can exceed 1 mA/mm of gate periphery causing a possible gate current of 30 mA for a 100 W device.

4. Temperature compensation

Similar to LDMOS devices, the gate threshold voltage for GaN devices is approximately proportional to temperature. The gate threshold voltage is the voltage required to maintain a constant quiescent drain current, which for Ampleon GaN devices, is about +1 mV/C junction temperature. However, practical temperature compensation circuits are obliged to monitor case temperature, where the temperature change is typically only half the junction temperature change. Thus, the bias controller must increase VGS by about +2 mV/C.

5. Summary

The characteristics of the bias controller module described in the following section are summarized in Table 1.

[1] Resistor values may have to be changed for part of range.

[2] Dependent upon PCB layout.

Table 1. Summary of bias controller characteristicsDrain voltage 12 V to 80 V [1]

Gate voltage 3 V to 1 V [1]

Gate voltage adjustment range 700 mV typicalGate voltage temperature compensation +2 mV/C typicalGate current, negative 10 mAGate current, positive 100 mAGate voltage ripple 2 mV (p-p)Switched drain current 40 A [2]




6. Circuit description

6.1 Negative voltage generationThe bias controller uses a switched-capacitor voltage inverter, U1, to generate a regulated 4 V from a single positive supply. The +5 V supply is generated from the high-voltage drain supply by linear regulator U4.

U1 operates at a switching frequency of approximately 550 kHz; C3, R4, and C10 are used to reduce output ripple to less than 2 mV (p-p).

When the output voltage is within 5 % of the 4 V set value, the REG output goes LOW. The REG output LOW signal acts as an active-LOW (power valid) signal to enable drain power to the GaN device.

6.2 Drain voltage switchingMost lower power HEMT bias controllers use a P-channel power MOSFET as the drain voltage load switch. This has the advantage of simplicity, often requiring nothing more than level-shifting transistors between the voltage inverter ‘power valid’ signal and the MOSFET gate. However, as load currents increase above 2 A to 5 A, the required MOSFET becomes large and expensive. Consequently, this bias controller uses a common hot-swap controller IC, U2 to drive an inexpensive N-channel MOSFET.

Fig 2. +5 V and 4 V voltage generation circuit

C71 μF

+5V+VD_IN 8

IN 1 OUT

5EN 2 SENSE

GND:4,9

U4

LT3010EMS8E−5

2C1+

5 COMP

8SHDN

6 OUT1VCC

3C1−

7 REG

GND:4

U1

LTC1261CS8−4

C6100 pF

R9

10 kΩ

R4

10 ΩC310 μF

C1010 μF

POWER_VALID_N

−4VC92.2 μF

C4100 nF

aaa-001667




U2 contains an internal charge pump for driving the gate of the external N-channel MOSFET, Qdrain. It also includes a programmable ramp-up rate, and optional overcurrent fault detection and foldback current limiting. If the voltage drop across sense resistor Rsense exceeds 55 mV, U2 disconnects power from the drain, and leaves it latched off until power is cycled.

Qdrain is a low-cost high-density TrenchMOS device in a small power SO8 package. It has a typical on-resistance of less than 10 m and a drain current limit of more than 80 A.

6.3 Temperature compensationThe bias controller uses a small-signal PNP transistor (mounted in contact with the baseplate) to monitor temperature and generate a +8 mV/C compensating voltage.

Fig 3. Drain voltage load switch circuit

2 FB

1UV

7 SENSE8VCC

5TIMER

6 GATE

3 PGD

GND:4

U2

LT4256−1CS8

R1768.1 kΩ

+VD_OUT+VD_IN

R1510 kΩ

C5100 nF

ENABLER310 kΩ

BZX385−C11

4

3521Qdrain

PSMN8R2−80YS

POWER_GOOD

C11100 nF

C110 nF

Rsense

0.005 Ω55 mV/Itrip

R23100 Ω

R2175 kΩ

R2210 Ω

aaa-001668

D4

Fig 4. Temperature compensating circuit

aaa-001669

R193.01 kΩ

R744.2 kΩ

R1810 kΩ

13

2

QtempBC857B

VTEMP

−4V




6.4 Gate voltage adjustmentA variable voltage derived from the 4 V supply is summed with the temperature monitor voltage to generate a temperature-compensated gate voltage. R13 and R14 are selected to set the desired gate voltage trim range, and R6 is selected to provide the desired amount of temperature compensation. Figure 6 shows typical values for VGS = 1.6 V.

U3 is a dual rail-to-rail high-current operational amplifier chosen because it is stable into any capacitive load. It can deliver more than 100 mA of output current to meet the positive gate current requirements of most GaN HEMTs.

Fig 5. Temperature compensating voltage

0 10 20 30 40 50 60 70 80 90 100−3.5

−3.4

−3.3

−3.2

−3.1

−3

−2.9

−2.8

−2.7

−2.6

−2.5

baseplate temperature (°C)

tem

pera

ture

com

pens

atio

n vo

ltage

(V)

aaa-001670




The output impedance of the bias source is low (less than 1 ) because of the feedback around operational amplifier U3. However, HEMT applications usually require a series gate resistor of 5 to 20 , instead of a bias inductor, to ensure low-frequency device stability.

Because the GaN HEMT quiescent gate current can increase at high temperatures, a significant voltage drop can be developed across this gate resistor, increasing VGS by 200 mV or more. This can be a serious problem because the increased gate voltage can push the HEMT operating point into a region of instability or even cause thermal runaway.

Fig 6. Gate voltage adjustment circuit

Fig 7. Gate voltage

1

3

2

R1810 kΩ

R744.2 kΩ

R11100 kΩ

R193.01 kΩ

13

2

QtempBC857B

R10

10 kΩ

R6

30.1 kΩ

−4V

4

3 5

2

1

U3LM7321MF

C81 μF

C2100 nF

C91 μF

Rg

10 Ω

R20

VGATE

R51 kΩ

R132 kΩ

R142 kΩ

1 kΩ

aaa-001671

0 10 20 30 40 50 60 70 80 90 100

baseplate temperature (°C)aaa-001672

−2

−1.9

−1.8

−1.7

−1.6

−1.5

−1.4

−1.3

−1.2

−1.1

−1VG pot fully CW

pot mid-scalepot fully CCW




One solution is to provide DC feedback from the HEMT gate terminal to the operational amplifier inverting input, allowing it to compensate for voltage dropped across gate resistor Rg. Feedback through R20 compensates for voltage dropped across Rg. To minimize RF non-linearity and memory effects, make sure that 1 / (R20 C8) is less than the lowest modulation frequency of the RF signal.

6.5 Resistor value selectionThe resistor values in the schematic are for a 50 V device with a nominal VGS of 2.1 V, +2 mV/C VGS temperature coefficient, and 11 A IDS overcurrent sense. Other nominal operating conditions may require resistor value changes:

• R17 determines the supply voltage at which the drain is connected.R17 = R3 (VD / 4 1), so VD = 31 V with the 68.1 k value in the design.

• R21 determines the supply voltage at which operating VGS is applied.R21 = R15 (VD / 4.45 1), so VD(good) = 38 V with the 75.0 k value in the design.

• Rsense determines the foldback current limit. ILIMIT = 0.055 / Rsense, so ILIMIT = 11 A with the 5 m value in the design.

6.6 Full schematicThe complete schematic of the bias controller combines the preceding subcircuits with ‘glue circuitry’ and several (possibly optional) additional convenience features.

• LEDs D1 and D2 provide visual indication of valid gate and drain voltages.• Switch S1 allows the GaN amplifier to be placed easily in ‘standby’, where the

nominal gate voltages are applied, but drain power is disconnected.• When S1 is set to ‘Vd on’ and the drain supply is not fully on (ramping up or down),

diode D3 and MOSFET Q3 turn on MOSFET Q2, pulling the gate voltage down to 4 V.

Table 2. Bias module bill of materialsComponent Description Value RemarksC9, C12 capacitor, 100 V 10 % X7R, 1206 1 FC7, C8 capacitor, 50 V 10 % X7R, 0805 1 FC2, C4, C5, C11 capacitor, 50 V 10 % X7R, 0805 100 nFC6 capacitor, 50 V 5 % NP0, 0805 100 pFC3, C10 capacitor, 10 V 20 % X7R, 0805 10 FC1 capacitor, 50 V 10 % X7R, 0805 10 nFD1 LED, green, 0805D2 LED, yellow, 0805D4 diode, Zener 11 V 300 mW BZX385-C11D3 dual diode, common-cathode BAV74L1 ferrite bead, 200 mA, 0805 1000 mH?Q1, Q2, Q4 transistor, N-ch MOS 30 V 0.8 A BSH103Q3 transistor, P-ch MOS 30 V 0.8 A BSS84R13, R14 resistor, 1 % 100 ppm CF, 0805 2.00 kR5 potentiometer, 5t cermet 1 k




R19 resistor, 1 % 100 ppm CF, 0805 3.01 kR7 resistor, 1 % 100 ppm CF, 0805 44.2 kR3, R9, R10, R12, R15,R16, R18

resistor, 1 % 100 ppm CF, 0805 10.0 k

R6 resistor, 1 % 100 ppm CF, 0805 30.1 kR4, R22, R24 resistor, 1 % 100 ppm CF, 0805 10.0 kR1, R8, R20 resistor, 1 % 100 ppm CF, 0805 1.00 kR17 resistor, 1 % 100 ppm CF, 0805 68.1 kR23 resistor, 1 % 100 ppm CF, 0805 100 kR2, R11 resistor, 1 % 100 ppm CF, 0805 100 kR21 resistor, 1 % 100 ppm CF, 0805 75.0 kS1 switch, SPDT right-angle SMD Tyco 1437575-1U4 voltage regulator, 5 V 100 mA Linear LT3010EMS8E-5U1 switching capacitor inverter Linear LTC1261CS8-4U2 hot swap controller Linear LT4256-1CS8U3 rail-rail opamp National LM7321MF

Table 2. Bias module bill of materialsComponent Description Value Remarks



xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx

AN11130#2

Application note

Rev. 2 —

1 September 2015

11 of 14

AN

11130B

ias module for 50 V G

aN dem

onstration boards

TE

D

SE

C110 nF

5

6

4

3

2

1

V+

D drain

G switching

S npn mosfet

R2210 Ω

R2175 kΩ

R23100 Ω

R1510 kΩ

D4

BZX384-C11

aaa-001673

All information provided in this docum

ent is subject to legal disclaimers.

© Am

pleon The Netherlands B.V. 2015. All rights reserved.

Fig 8. Bias module schematic

L1BLM21BD102

IN

EN

U4LT3010EMS8E−5

C91 μF

C121 μF

C71 μF

C6100 pF

C310 μF

GND:4,9

OUT

SENSE

+5V8

5

1

2

2C1+

8SHDN

1VCC

3C1−

U1LTC1261CS8−4

C2100 nF

C1010 μF

R9

5 COMP

6 OUT

7 REG

GND:4

C4100 nF

10 kΩ

12

3

BSS84Q3

R410 Ω

R11 kΩ

D3

D3

BAW56

BAW56

R2100 kΩ

R1610 kΩ

R132 kΩ

R10

10 kΩ

R51 kΩ

R142 kΩ

1UV GA

8VCC

5TIMER 3 PG

7

6

SEN

2 FB

GND:4

13

2

Q1BSH103

13

2

Q2BSH103 C8

1 μF

C5100 nF

C11100N

R310 kΩ

R1768.1 kΩ

R1810 kΩ

R744.2 kΩ

R193.01 kΩ

1

3

2

R20

1 kΩ

R8

1 kΩ

R12

10 kΩ

R6

30.1 kΩ7

8

9

C temperature

B compensation

E npn transistor

10

11

12

VG

FB

R11100 kΩ

13 2

Q4BSH103

-4V

4

3 5

2

1

U3LM7321MF

2

1

3

3

R24

10 Ω

1

23

VD on

S11437575−1standby

D1HSMG−C170green = VG on

D2HSMY−C170yellow = VD on

U2LT4256-1CS8


7. PCB layout

8. Abbreviations

Fig 9. PCB top-side layout

aaa-001674

Fig 10. PCB bottom-side layout

aaa-001675

Table 3. AbbreviationsAcronym DescriptionLDMOS Laterally Diffused Metal Oxide SemiconductorMOSFET Metal Oxide Semiconductor Field Effect Transistor




9. Legal information

9.1 DefinitionsDraft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. Ampleon does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information.

9.2 DisclaimersLimited warranty and liability — Information in this document is believed to be accurate and reliable. However, Ampleon does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Ampleon takes no responsibility for the content in this document if provided by an information source outside of Ampleon.

In no event shall Ampleon be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory.

Notwithstanding any damages that customer might incur for any reason whatsoever, Ampleon’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of Ampleon.

Right to make changes — Ampleon reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof.

Suitability for use — Ampleon products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an Ampleon product can reasonably be expected to result in personal injury, death or severe property or environmental damage. Ampleon and its suppliers accept no liability for inclusion and/or use of Ampleon products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk.

Applications — Applications that are described herein for any of these products are for illustrative purposes only. Ampleon makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification.

Customers are responsible for the design and operation of their applications and products using Ampleon products, and Ampleon accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the Ampleon product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products.

Ampleon does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using Ampleon products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). Ampleon does not accept any liability in this respect.

Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities.

Evaluation products — This product is provided on an “as is” and “with all faults” basis for evaluation purposes only. Ampleon, its affiliates and their suppliers expressly disclaim all warranties, whether express, implied or statutory, including but not limited to the implied warranties of non-infringement, merchantability and fitness for a particular purpose. The entire risk as to the quality, or arising out of the use or performance, of this product remains with customer.

In no event shall Ampleon, its affiliates or their suppliers be liable to customer for any special, indirect, consequential, punitive or incidental damages (including without limitation damages for loss of business, business interruption, loss of use, loss of data or information, and the like) arising out the use of or inability to use the product, whether or not based on tort (including negligence), strict liability, breach of contract, breach of warranty or any other theory, even if advised of the possibility of such damages.

Notwithstanding any damages that customer might incur for any reason whatsoever (including without limitation, all damages referenced above and all direct or general damages), the entire liability of Ampleon, its affiliates and their suppliers and customer’s exclusive remedy for all of the foregoing shall be limited to actual damages incurred by customer based on reasonable reliance up to the greater of the amount actually paid by customer for the product or five dollars (US$5.00). The foregoing limitations, exclusions and disclaimers shall apply to the maximum extent permitted by applicable law, even if any remedy fails of its essential purpose.

9.3 TrademarksNotice: All referenced brands, product names, service names and trademarks are the property of their respective owners.

Any reference or use of any ‘NXP’ trademark in this document or in or on thesurface of Ampleon products does not result in any claim, liability orentitlement vis-à-vis the owner of this trademark. Ampleon is no longer part ofthe NXP group of companies and any reference to or use of the ‘NXP’ trademarks will be replaced by reference to or use of Ampleon’s own Any reference or use of any ‘NXP’ trademark in this document or in or on thesurface of Ampleon products does not result in any claim, liability orentitlement vis-à-vis the owner of this trademark. Ampleon is no longer part ofthe NXP group of companies and any reference to or use of the ‘NXP’trademarks will be replaced by reference to or use of Ampleon’s own trademarks.




10. Contents

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Bias sequencing . . . . . . . . . . . . . . . . . . . . . . . . 33 Gate current . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Temperature compensation . . . . . . . . . . . . . . . 45 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Circuit description . . . . . . . . . . . . . . . . . . . . . . . 56.1 Negative voltage generation. . . . . . . . . . . . . . . 56.2 Drain voltage switching. . . . . . . . . . . . . . . . . . . 56.3 Temperature compensation . . . . . . . . . . . . . . . 66.4 Gate voltage adjustment. . . . . . . . . . . . . . . . . . 76.5 Resistor value selection . . . . . . . . . . . . . . . . . . 96.6 Full schematic. . . . . . . . . . . . . . . . . . . . . . . . . . 97 PCB layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 Abbreviations. . . . . . . . . . . . . . . . . . . . . . . . . . 129 Legal information. . . . . . . . . . . . . . . . . . . . . . . 139.1 Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 139.2 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 139.3 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 1310 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

© Ampleon The Netherlands B.V. 2015. All rights reserved.For more information, please visit: http://www.ampleon.comFor sales office addresses, please visit: http://www.ampleon.com/sales

Date of release: 1 September 2015Document identifier: AN11130#2

Please be aware that important notices concerning this document and the product(s)described herein, have been included in section ‘Legal information’.

1. Introduction2. Bias sequencing3. Gate current4. Temperature compensation5. Summary6. Circuit description6.1 Negative voltage generation6.2 Drain voltage switching6.3 Temperature compensation6.4 Gate voltage adjustment6.5 Resistor value selection6.6 Full schematic

7. PCB layout8. Abbreviations9. Legal information9.1 Definitions9.2 Disclaimers9.3 Trademarks

10. Contents

Documents

AN11130 - Ampleon...Table 1. Summary of bias con [1] Resistor values may have to be changed for part of range. [2] Dependent upon PCB layout. troller characteristics Drain voltage