Upload
bertram-johnson
View
219
Download
0
Tags:
Embed Size (px)
Citation preview
An Introduction to the Windows-An Introduction to the Windows-based PC Programming Toolbased PC Programming Tool
Version 0.91Version 0.91Windows-based PC programming package for panel set up, zones, text, local and network cause/effect, Discovery mode types, sensitivity levels and day/night timings.
Windows-based PC programming package for panel set up, zones, text, local and network cause/effect, Discovery mode types, sensitivity levels and day/night timings.
An Introduction to the Windows-An Introduction to the Windows-based PC Programming Toolbased PC Programming Tool
•Windows Based
•Create and Manage project files for a site of networked panels & graphics systems
•Upload and download files
•Engineer definable password control
•Setup panel layout including loops, repeaters, & panel expansion boards
•Provide text for all panel and loop inputs and outputs for reference and downloading purposes
•Setup output delay by day/night
•Setup 4 internal timers programmable under cause/effect control (ie for phased evac)
An Introduction to the Windows-An Introduction to the Windows-based PC Programming Toolbased PC Programming Tool
•Configure Default & Day & night, Threshold/Mode settings
•Configure default loop Interface input device responses for, Fire, Alert, Fault, Indication only, N/O,N/C input
•Configure special group mode settings changeable by triggering a loop input device
•Configure any panel and loop input into 1 zone for indication and cause/effect and 7 additional hidden control groups for cause/effect (zones 1-32 for indication, 33-255 for cause effect)
•Link any output device into as many zones/groups as required for cause/effect, detailing the conditions required for activation
An Introduction to the Windows-An Introduction to the Windows-based PC Programming Toolbased PC Programming Tool
•Detail the conditions required to inhibit any output device from operating and link to as many zones / groups as required for cause/effect
•Programme Detector base platform sounders
•Print out all files for reference and approval purposes
•Supports earlier panels manufactured for backward compatibility (Not all features are available on earlier panels)
•Configure network personality responses by simple drop down lists
•Configure extensive network cause/effect via 520 standard “Flag” messages and up to 1,500 custom configured ones – per panel
•Full training and support provided
ALARMS
FIRE & FAULT RELAYS
BREAK GLASS
F IRE
PRESS HERE
I SOLATOR
BREAK GLASSPRESS HERE
F IRE
I SOLATOR
F I RE
PRESS HERE
BREAK GLASS
HAZARDOUS AREA
PRESS HERE
BREAK GLASS
F IREA1445
A1445A1444/ 7
A1445
APOLLO
A1446
A1444
A1445
TRANSLATOR
EXTINGUISHING
SYSTEM
CONVENTIONAL
FIRE PANEL
FIRE DAMPER
MONITORING
BEAM DETECTOR
RELAY OUTPUT UNIT
MINI SWITCH MONITOR
WITH INTERRUPT
REMOTE INDICATOR
BARRIER
BARRIER
ZONE 1
ZONE 2
ZONE 3
ZONE 4
ZONE 5
ZONE 6
ZONE 7
ZONE 8
Discovery Panel HardwareDiscovery Panel Hardware
Fully programmable network comprising of Discovery and Voyager panels, graphics systems and Integra network repeaters.
Fully programmable network comprising of Discovery and Voyager panels, graphics systems and Integra network repeaters.
Up to 31 8-way panel enhancement boards may be added.
Two types are available:
1) fully-programmable inputs and relay outputs2) fully-programmable inputs and alarm outputs
Up to 31 8-way panel enhancement boards may be added.
Two types are available:
1) fully-programmable inputs and relay outputs2) fully-programmable inputs and alarm outputs
Up to 14 fully functional repeater panels may be connected via RS485 cable.
Up to 14 fully functional repeater panels may be connected via RS485 cable.
Individual panels and network configurations and cause / effect are programmable via Windows PC package.
Individual panels and network configurations and cause / effect are programmable via Windows PC package.
The Preparation showing The Preparation showing the Panel Layout Chartthe Panel Layout Chart
Loop No.Device No.
Device Type
Add text as required
Loop No.Device No.
Device Type
Add text as required Groups
The Discovery panel provides 7 hidden
groups. Loop devices and programmable
panel inputs may be grouped together
for Cause / Effect programming
Groups
The Discovery panel provides 7 hidden
groups. Loop devices and programmable
panel inputs may be grouped together
for Cause / Effect programming
Display Text
Insert the Text that
will appear on the
LCD Display
Display Text
Insert the Text that
will appear on the
LCD Display
Zone No. and Location
Insert the Zone number that
will appear on the Zone LED
display.
Location added for
engineers reference
Zone No. and Location
Insert the Zone number that
will appear on the Zone LED
display.
Location added for
engineers reference
The Preparation Showing The Preparation Showing the Panel Cause / Effect Chartthe Panel Cause / Effect Chart
2) Cause
Enter all panel and loop
inputs to be programmed
to trigger programmable
outputs
2) Cause
Enter all panel and loop
inputs to be programmed
to trigger programmable
outputs
3) Cause Conditions
Enter notes as required
3) Cause Conditions
Enter notes as required
4) Matrix
Complete the
Cause / Effect matrix
4) Matrix
Complete the
Cause / Effect matrix
1) Effect
Enter all Loop and Panel outputs with their function and detailing if the device is a sounder or relay
1) Effect
Enter all Loop and Panel outputs with their function and detailing if the device is a sounder or relay
Installing the SoftwareInstalling the Software
Information
The software uses the industry
standard Install Shield for installation
and will therefore lead the engineer
through the installation process
Information
The software uses the industry
standard Install Shield for installation
and will therefore lead the engineer
through the installation process
The Start up ScreenThe Start up Screen
Step 1
The opening screen will enable you to open an
existing project file or create a new one
Step 1
The opening screen will enable you to open an
existing project file or create a new one
Opening and existing file
Navigate you way to the required file
identified by its job number
Opening and existing file
Navigate you way to the required file
identified by its job number
Creating a new file
You will be prompted for a
5 DIGIT job number
then prompted to enter a
FILE LOCATION
followed by a
CONTRACT NAME
for you reference
Creating a new file
You will be prompted for a
5 DIGIT job number
then prompted to enter a
FILE LOCATION
followed by a
CONTRACT NAME
for you reference
File ManagementFile Management
Information
The files should be saved into
folders on the hard drive with a file
name of 8 characters maximum.
Sub folders with the contract identification
may be either names or numbers.
If named sub folders are used
then the contract number can be
Located within that folder
Information
The files should be saved into
folders on the hard drive with a file
name of 8 characters maximum.
Sub folders with the contract identification
may be either names or numbers.
If named sub folders are used
then the contract number can be
Located within that folder
The Programming Process The Programming Process from Coldfrom Cold
Enter the list of Panels required
in the “Add a Panel” function
Select apanel to be
programmed
Configure The Panel
layout (Loops,
Repeaters,Expansion
Boards)
Configure the list Of all loop
Output Devices adding
The text labelFor later
Reference purposes
Print out all filesFor project file
Text label All Loop and Panel inputs,
Set up the Special
Functions including
timers and network
responses
Allocate all The panel and
Loop devices into Zones and
Control groups
Return to the List of panel and
Loop outputsAnd configureCause/effect
Print out all files For customer
approval
Text label All other
panelOutputs
Download topanel
Create Hexfiles
Amend filesIf required from
Customer response
Print out All text files
For referencepurposes
The Programming Process from The Programming Process from uploaded filesuploaded files
Enter the list of Panels required in the “Add a Panel” function
Select a panel to be programmed
Upload files From selected panel
Continue as previous slide
Selecting The Panel ListSelecting The Panel List
Step 1 Add a Panel
The opening Screen enables the engineer to “Add a Panel” to either and existing list of panel on that project or create a list of panels for a project
Step 1 Add a Panel
The opening Screen enables the engineer to “Add a Panel” to either and existing list of panel on that project or create a list of panels for a project
Step 2 Chose from the panel list
Selecting the correct panel to add to the panel list in essential for correct programming. A panel name should also be entered for identification and downloading. The select “OK”
Note:
Older panels are also included in this list for “on going” engineering support
Step 2 Chose from the panel list
Selecting the correct panel to add to the panel list in essential for correct programming. A panel name should also be entered for identification and downloading. The select “OK”
Note:
Older panels are also included in this list for “on going” engineering support
Information
If you are going to network panels together then it is essential that all panels are listed in the same project
Information
If you are going to network panels together then it is essential that all panels are listed in the same project
The Panel ListThe Panel List
Step 1 Select the panel
Click on the required panel
Step 1 Select the panel
Click on the required panel
Step 2 Proceeding
Select Edit Panel Data
Step 2 Proceeding
Select Edit Panel Data
Information
If you have incorrectly added a panel to the list it may be deleted
from the list by selecting the panel and then selecting delete
panel.
Warning
Any configuration already programmed into the deleted
panel will also be deleted
Information
If you have incorrectly added a panel to the list it may be deleted
from the list by selecting the panel and then selecting delete
panel.
Warning
Any configuration already programmed into the deleted
panel will also be deleted
The Main Editor ScreenThe Main Editor Screen
Step 2 Select Output
The engineerhe engineer should enter should enter the address and location of the address and location of all loop output devices for all loop output devices for later reference purposeslater reference purposes
Step 2 Select Output
The engineerhe engineer should enter should enter the address and location of the address and location of all loop output devices for all loop output devices for later reference purposeslater reference purposes
Step 4 Special Functions
Allows the engineer to configure the Day / Night and Delay timers, Set up the 4 inbuilt software timers, Re-define the engineers access code, and configure the network basic personality responses, Set up platform sounders
Step 4 Special Functions
Allows the engineer to configure the Day / Night and Delay timers, Set up the 4 inbuilt software timers, Re-define the engineers access code, and configure the network basic personality responses, Set up platform sounders
Step 1 Panel Layout
Panel layout allows the engineer to select the number of loops, the number of repeaters and the number and type of 8 way I/O cards configured onto the panel
Step 1 Panel Layout
Panel layout allows the engineer to select the number of loops, the number of repeaters and the number and type of 8 way I/O cards configured onto the panel
Step 5 Sensitivity
Allows the engineer to map the default loop devices (ie XP95 and Discovery), their default sensitivities, and the sensitivity settings for each device as set up by the Day / Night timers and manual loop inputs.
Step 5 Sensitivity
Allows the engineer to map the default loop devices (ie XP95 and Discovery), their default sensitivities, and the sensitivity settings for each device as set up by the Day / Night timers and manual loop inputs.
Step 3 Edit Texts
Allows the engineer to enter the location text for each loop device and text for all other inputs and outputs configured onto the panel. This is essential for later reference purposes
Step 3 Edit Texts
Allows the engineer to enter the location text for each loop device and text for all other inputs and outputs configured onto the panel. This is essential for later reference purposes
Step 6 Allocate Zones / Groups
Allows the engineer to allocate every loop and panel input into 1 visible indication zone and 7 additional hidden groups for cause / effect programming
Step 6 Allocate Zones / Groups
Allows the engineer to allocate every loop and panel input into 1 visible indication zone and 7 additional hidden groups for cause / effect programming
Step 7 Select Output
TThe engineerhe engineershould now should now programme the output programme the output response (Cause / response (Cause / Effect) of every output Effect) of every output device on the panel and device on the panel and loopsloops
Step 7 Select Output
TThe engineerhe engineershould now should now programme the output programme the output response (Cause / response (Cause / Effect) of every output Effect) of every output device on the panel and device on the panel and loopsloops
Panel Layout ScreenPanel Layout Screen
Step 3 I/O boards
Up to 31x 8 way I/O boards may be Up to 31x 8 way I/O boards may be configured to each panel. The boards configured to each panel. The boards have either alarm or relay outputs and have either alarm or relay outputs and may be configured for different types of may be configured for different types of input responses (Refer to I/O board input responses (Refer to I/O board manual)manual)
Step 3 I/O boards
Up to 31x 8 way I/O boards may be Up to 31x 8 way I/O boards may be configured to each panel. The boards configured to each panel. The boards have either alarm or relay outputs and have either alarm or relay outputs and may be configured for different types of may be configured for different types of input responses (Refer to I/O board input responses (Refer to I/O board manual)manual)
Step 2 Select number of repeaters
Use the up / down arrows to select from Use the up / down arrows to select from 0 to 10 to 144 panels repeaters panels repeaters
Step 2 Select number of repeaters
Use the up / down arrows to select from Use the up / down arrows to select from 0 to 10 to 144 panels repeaters panels repeaters
Step 1 Select number of loops
Use the up / down arrows to select from Use the up / down arrows to select from 1 to 2 loops (Voyager) or 1 to 2 loops (Voyager) or 1 to 4 loops1 to 4 loops (Discovery)(Discovery)
Step 1 Select number of loops
Use the up / down arrows to select from Use the up / down arrows to select from 1 to 2 loops (Voyager) or 1 to 2 loops (Voyager) or 1 to 4 loops1 to 4 loops (Discovery)(Discovery)
Step 4 Select OK
When the desired setup is achieved then When the desired setup is achieved then select OK to save settingsselect OK to save settings
Step 4 Select OK
When the desired setup is achieved then When the desired setup is achieved then select OK to save settingsselect OK to save settings
Creating a List of Loop Output Creating a List of Loop Output DevicesDevices
Step 1 Loop Output Selection
Click on “Select Output” followed by “Loop Output”
Step 1 Loop Output Selection
Click on “Select Output” followed by “Loop Output”
Note 1
The “Select Loop Output” screen will then be revealed indicating any outputs previously listed for programming.
Note 1
The “Select Loop Output” screen will then be revealed indicating any outputs previously listed for programming.
Step 2 New
Select “New” to proceed to the list of loops and devices for adding to the list (Shown on next slide)
or “OK” to proceed to configure the selected output.
Step 2 New
Select “New” to proceed to the list of loops and devices for adding to the list (Shown on next slide)
or “OK” to proceed to configure the selected output.
Note 2
The Apollo output bits 0, 1, 2 are referred to as A, B, C
Note 2
The Apollo output bits 0, 1, 2 are referred to as A, B, C
Creating a List of Loop Output Creating a List of Loop Output DevicesDevices
Output Selection
Select the loop, address and output channel (Bit) required and then press OK
Output Selection
Select the loop, address and output channel (Bit) required and then press OK
Note
The Apollo output bits 0, 1, 2 are referred to as A, B, C
Note
The Apollo output bits 0, 1, 2 are referred to as A, B, C
Creating a List of Loop Output Creating a List of Loop Output DevicesDevices
Entering a Text Label
Enter the text required for the output selected.
Entering a Text Label
Enter the text required for the output selected.
Note:
The text label is not downloaded to the panel but is is useful for reference purposes.
Note:
The text label is not downloaded to the panel but is is useful for reference purposes.
A Completed List of Loop A Completed List of Loop Output DevicesOutput Devices
Information
Continue to select “New” to proceed to the list of loops and devices for adding to the list
or “OK” to proceed to configure the selected output.
Or Exit to proceed to the next functionOr Exit to proceed to the next function
Information
Continue to select “New” to proceed to the list of loops and devices for adding to the list
or “OK” to proceed to configure the selected output.
Or Exit to proceed to the next functionOr Exit to proceed to the next function
Text InputText Input
Note
Text may be allocated to all input and output devices for reference purposes but panel and loop outputs are not sent to the panel or displayed upon activation.
Note
Text may be allocated to all input and output devices for reference purposes but panel and loop outputs are not sent to the panel or displayed upon activation.
Step 1 Category
Select the category for text allocation. You may then be prompted further before the text screen is revealed (i.e. selecting “sensors” will prompt the engineer for the loop number)
Step 1 Category
Select the category for text allocation. You may then be prompted further before the text screen is revealed (i.e. selecting “sensors” will prompt the engineer for the loop number)
Step 2 Adding Text
Add the required text noting the availability of shortcut function keys
Step 2 Adding Text
Add the required text noting the availability of shortcut function keys
Step 3 Saving the Text
Press the “Enter” to save the entered text. Then press “Save” to exit.
Step 3 Saving the Text
Press the “Enter” to save the entered text. Then press “Save” to exit.
The Panel Delay SettingsThe Panel Delay Settings
The Set the panel delay
A 24 hr clock allows the engineer to A 24 hr clock allows the engineer to define the period and duration to delay define the period and duration to delay all sounder and relay outputsall sounder and relay outputs
The Set the panel delay
A 24 hr clock allows the engineer to A 24 hr clock allows the engineer to define the period and duration to delay define the period and duration to delay all sounder and relay outputsall sounder and relay outputs
Information
The example here means that any fire The example here means that any fire operation will delay all alarms and operation will delay all alarms and programmed cause/effect (including programmed cause/effect (including transmission of network cause / effect) transmission of network cause / effect) for 1 minute between 9.00 am and 5.00 for 1 minute between 9.00 am and 5.00 pm.pm.
Information
The example here means that any fire The example here means that any fire operation will delay all alarms and operation will delay all alarms and programmed cause/effect (including programmed cause/effect (including transmission of network cause / effect) transmission of network cause / effect) for 1 minute between 9.00 am and 5.00 for 1 minute between 9.00 am and 5.00 pm.pm.
Note
All panel repeaters, pagers and printer All panel repeaters, pagers and printer operation, and network indications are operation, and network indications are not delayed.not delayed.
Note
All panel repeaters, pagers and printer All panel repeaters, pagers and printer operation, and network indications are operation, and network indications are not delayed.not delayed.
The Day / Night SettingsThe Day / Night Settings
The Day / Night sensitivity clock
A 7 day programmer is used to define A 7 day programmer is used to define the day time period for mode change the day time period for mode change (Discovery) and Trip levels (XP95)(Discovery) and Trip levels (XP95)
The Day / Night sensitivity clock
A 7 day programmer is used to define A 7 day programmer is used to define the day time period for mode change the day time period for mode change (Discovery) and Trip levels (XP95)(Discovery) and Trip levels (XP95)
Information
The example here shows day time being The example here shows day time being defined as Monday – Friday 9.00 am to defined as Monday – Friday 9.00 am to 5.00 pm. The company does not work 5.00 pm. The company does not work weekends and therefore the weekends weekends and therefore the weekends are defined as outside day time working.are defined as outside day time working.
Information
The example here shows day time being The example here shows day time being defined as Monday – Friday 9.00 am to defined as Monday – Friday 9.00 am to 5.00 pm. The company does not work 5.00 pm. The company does not work weekends and therefore the weekends weekends and therefore the weekends are defined as outside day time working.are defined as outside day time working.
The Software TimersThe Software Timers
The panels 4 internal delay Timers
4 internal timers may be set for use with the panels cause/effect. Typical 4 internal timers may be set for use with the panels cause/effect. Typical uses may be phased evacuation, shutdown delays, signalling delays, start uses may be phased evacuation, shutdown delays, signalling delays, start up delays etc.up delays etc.
The panels 4 internal delay Timers
4 internal timers may be set for use with the panels cause/effect. Typical 4 internal timers may be set for use with the panels cause/effect. Typical uses may be phased evacuation, shutdown delays, signalling delays, start uses may be phased evacuation, shutdown delays, signalling delays, start up delays etc.up delays etc.
Delay Timer Operation
Each timer is connected to a Virtual Panel Each timer is connected to a Virtual Panel Input and Output (Designated Inputs / Input and Output (Designated Inputs / Outputs 249-252 {Remembering that the Outputs 249-252 {Remembering that the panel may have up to 248 actual panel panel may have up to 248 actual panel inputs / outputs via the 8 way expansion inputs / outputs via the 8 way expansion cards}). cards}).
The inputs are added to the list of panel The inputs are added to the list of panel inputs found in “Zones/groups” and the inputs found in “Zones/groups” and the outputs are listed in “Select Output” outputs are listed in “Select Output”
Example:Example:
By configuring a cause condition to output By configuring a cause condition to output 249, the timer 1 will start when that 249, the timer 1 will start when that condition is activated. At the end of the condition is activated. At the end of the delay set here input 249 will then be delay set here input 249 will then be triggered and available as a zone cause for triggered and available as a zone cause for triggering further cause/effect. triggering further cause/effect.
Delay Timer Operation
Each timer is connected to a Virtual Panel Each timer is connected to a Virtual Panel Input and Output (Designated Inputs / Input and Output (Designated Inputs / Outputs 249-252 {Remembering that the Outputs 249-252 {Remembering that the panel may have up to 248 actual panel panel may have up to 248 actual panel inputs / outputs via the 8 way expansion inputs / outputs via the 8 way expansion cards}). cards}).
The inputs are added to the list of panel The inputs are added to the list of panel inputs found in “Zones/groups” and the inputs found in “Zones/groups” and the outputs are listed in “Select Output” outputs are listed in “Select Output”
Example:Example:
By configuring a cause condition to output By configuring a cause condition to output 249, the timer 1 will start when that 249, the timer 1 will start when that condition is activated. At the end of the condition is activated. At the end of the delay set here input 249 will then be delay set here input 249 will then be triggered and available as a zone cause for triggered and available as a zone cause for triggering further cause/effect. triggering further cause/effect.
The Principles of the The Principles of the Software Timer OperationSoftware Timer Operation
Input 249 OutputInput 250 OutputInput 251 OutputInput 252 Output
Virtual Panel outputsFrom “Select Output”And programmed via
cause/effect to start timer
Virtual Panel Inputs Shown in “Zones/Groups”
Now available to programme cause/effect
( as indication input)
Start PointEnd Point
Changing the Access CodeChanging the Access Code
Defining the Engineers Access Code
By entering the currnet access code the By entering the currnet access code the engineer may then define a new one. engineer may then define a new one. Note that the panel access code also Note that the panel access code also needs changing.needs changing.
Defining the Engineers Access Code
By entering the currnet access code the By entering the currnet access code the engineer may then define a new one. engineer may then define a new one. Note that the panel access code also Note that the panel access code also needs changing.needs changing.
Setting The Network ResponsesSetting The Network Responses
Note:
The “Job details” section here shows the The “Job details” section here shows the Panel being programmedPanel being programmed
Note:
The “Job details” section here shows the The “Job details” section here shows the Panel being programmedPanel being programmed
Step 1 Select panel to receive from
The drop down list will show all panels in The drop down list will show all panels in the networkthe network
Step 1 Select panel to receive from
The drop down list will show all panels in The drop down list will show all panels in the networkthe network
Step 2 Configure responses
Configure the display, print and memory Configure the display, print and memory functions accepted from the selected functions accepted from the selected pane. Panel name only, device text or pane. Panel name only, device text or ignore options are available. The user ignore options are available. The user controls may be ignored or accepted per controls may be ignored or accepted per control from each panelcontrol from each panel
Step 2 Configure responses
Configure the display, print and memory Configure the display, print and memory functions accepted from the selected functions accepted from the selected pane. Panel name only, device text or pane. Panel name only, device text or ignore options are available. The user ignore options are available. The user controls may be ignored or accepted per controls may be ignored or accepted per control from each panelcontrol from each panel
Note:
A different response may be configured A different response may be configured for and from every panel on the networkfor and from every panel on the network
Note:
A different response may be configured A different response may be configured for and from every panel on the networkfor and from every panel on the networkStep 3 Save
Save configurations
Step 3 Save
Save configurations
Platform Sounder SetupPlatform Sounder Setup
Using CEL Platform Sounders
By highlighting and selecting the By highlighting and selecting the detector address to be used with detector address to be used with the Platform Sounders, the panel the Platform Sounders, the panel will then operate the detector base will then operate the detector base output bit 0 on Test Alarms, output bit 0 on Test Alarms, Evacuate, Class Change, 1 person Evacuate, Class Change, 1 person test and with the panels test and with the panels Cause/effect. The output will cease Cause/effect. The output will cease on Silence Alarms. on Silence Alarms.
Using CEL Platform Sounders
By highlighting and selecting the By highlighting and selecting the detector address to be used with detector address to be used with the Platform Sounders, the panel the Platform Sounders, the panel will then operate the detector base will then operate the detector base output bit 0 on Test Alarms, output bit 0 on Test Alarms, Evacuate, Class Change, 1 person Evacuate, Class Change, 1 person test and with the panels test and with the panels Cause/effect. The output will cease Cause/effect. The output will cease on Silence Alarms. on Silence Alarms.
Default Sensitivity and Loop Default Sensitivity and Loop Device-Type SetupDevice-Type Setup
Note:
The engineer may upload the “autolearned” information The engineer may upload the “autolearned” information from the installed panel or allocate the loop device types from the installed panel or allocate the loop device types and sensitivities from “cold”. At this stage the device types and sensitivities from “cold”. At this stage the device types and default sensitivities of an “autolearned” loop will be and default sensitivities of an “autolearned” loop will be displayed. Otherwise the default will be “Non Analogue” displayed. Otherwise the default will be “Non Analogue”
Note:
The engineer may upload the “autolearned” information The engineer may upload the “autolearned” information from the installed panel or allocate the loop device types from the installed panel or allocate the loop device types and sensitivities from “cold”. At this stage the device types and sensitivities from “cold”. At this stage the device types and default sensitivities of an “autolearned” loop will be and default sensitivities of an “autolearned” loop will be displayed. Otherwise the default will be “Non Analogue” displayed. Otherwise the default will be “Non Analogue”
For setup from “Cold” proceed as belowFor setup from “Cold” proceed as below
Step 1 Loop
Select the loop to be configuredSelect the loop to be configured
Step 1 Loop
Select the loop to be configuredSelect the loop to be configured
Step 2 Default Device Settings
Select the device (or Select All) followed by the categories Select the device (or Select All) followed by the categories (Shown) to set up the device types configured to the loop. (Shown) to set up the device types configured to the loop. and default (Off) trip levels and sensitivities and the XP95 and default (Off) trip levels and sensitivities and the XP95 I/O settingsI/O settings
Step 2 Default Device Settings
Select the device (or Select All) followed by the categories Select the device (or Select All) followed by the categories (Shown) to set up the device types configured to the loop. (Shown) to set up the device types configured to the loop. and default (Off) trip levels and sensitivities and the XP95 and default (Off) trip levels and sensitivities and the XP95 I/O settingsI/O settings
Step 4 Save
Save the details
and then Quit
Step 4 Save
Save the details
and then Quit
Note:
A A “S“Select allelect all”” or or “D“De-selecte-select”” all is a useful shortcut where all is a useful shortcut where most or all of the loop is of one typemost or all of the loop is of one type
Note:
A A “S“Select allelect all”” or or “D“De-selecte-select”” all is a useful shortcut where all is a useful shortcut where most or all of the loop is of one typemost or all of the loop is of one type
Step 3 Sensitivities
Select the device (or select all) then Select the device (or select all) then select the appropriate device trip level select the appropriate device trip level or sensitivity mode or I/O responseor sensitivity mode or I/O response
Step 3 Sensitivities
Select the device (or select all) then Select the device (or select all) then select the appropriate device trip level select the appropriate device trip level or sensitivity mode or I/O responseor sensitivity mode or I/O response
Note:
An I/O unit (Only) input can be changed
between “Fire, Alert, Fault, Indication.
Note:
An I/O unit (Only) input can be changed
between “Fire, Alert, Fault, Indication.
Setting the Day-Night SensitivitySetting the Day-Night Sensitivity
Note:
The day and night Trip levels (XP95) and The day and night Trip levels (XP95) and Mode settings (Discovery) may be set up for Mode settings (Discovery) may be set up for every device every device
Note:
The day and night Trip levels (XP95) and The day and night Trip levels (XP95) and Mode settings (Discovery) may be set up for Mode settings (Discovery) may be set up for every device every device
Step 1Settings
Select the device (s) to be configured Select the device (s) to be configured
Step 1Settings
Select the device (s) to be configured Select the device (s) to be configured
Step 2 Day / Night
From the “Settings” menu select the From the “Settings” menu select the Day/Night and device type required. Day/Night and device type required.
Step 2 Day / Night
From the “Settings” menu select the From the “Settings” menu select the Day/Night and device type required. Day/Night and device type required.
Step 3 Mode
Select the Mode (illustrated) or Trip level Select the Mode (illustrated) or Trip level required required
Step 3 Mode
Select the Mode (illustrated) or Trip level Select the Mode (illustrated) or Trip level required required
Step 4 Save
Save Details and exit (Done) Save Details and exit (Done)
Step 4 Save
Save Details and exit (Done) Save Details and exit (Done)
Setting the Manual Mode SensitivitySetting the Manual Mode Sensitivity
Note:1
The required Discovery devices must be The required Discovery devices must be programmed into the appropriate programmed into the appropriate control control
group. Devices may be programmed across group. Devices may be programmed across loops intoloops into control control groups. groups.
There are 4 groups reserved for this facility There are 4 groups reserved for this facility
Note:1
The required Discovery devices must be The required Discovery devices must be programmed into the appropriate programmed into the appropriate control control
group. Devices may be programmed across group. Devices may be programmed across loops intoloops into control control groups. groups.
There are 4 groups reserved for this facility There are 4 groups reserved for this facility
Note:2
A loop input A loop input device device is used to trigger the is used to trigger the mode change mode change
Note:2
A loop input A loop input device device is used to trigger the is used to trigger the mode change mode change
Step 1 Changing the Mode
Use the “Up - Down” arrows to set the mode Use the “Up - Down” arrows to set the mode the devices will change to when the input is the devices will change to when the input is
triggered triggered
Step 1 Changing the Mode
Use the “Up - Down” arrows to set the mode Use the “Up - Down” arrows to set the mode the devices will change to when the input is the devices will change to when the input is
triggered triggered
Step 2 Save
Select “Save” to save changes Select “Save” to save changes
Step 2 Save
Select “Save” to save changes Select “Save” to save changes
Allocating Loop Devices into Allocating Loop Devices into Zones and GroupsZones and Groups
Step 1 Selecting Devices
Select the loop, devices and then zone required.
Step 1 Selecting Devices
Select the loop, devices and then zone required.
Step 2 Adding
Select the “Add” button to add the devices to the zone or group selected.
Step 2 Adding
Select the “Add” button to add the devices to the zone or group selected.
Note
Zones are listed as numbered 1-32 and will indicate on the zone LED’s on the panel when triggered
Groups are listed as 33-255 and will not indicate on the panels zone LED’s when triggered
Note
Zones are listed as numbered 1-32 and will indicate on the zone LED’s on the panel when triggered
Groups are listed as 33-255 and will not indicate on the panels zone LED’s when triggered
Allocating Panel InputsAllocating Panel Inputsinto Zones and Groupsinto Zones and Groups
Step 1 Selecting the Input
Select panel input and zone / group required.
Step 1 Selecting the Input
Select panel input and zone / group required.
Step 2 Adding
Select the “Add” button to add the devices to the zone or group selected.
Step 2 Adding
Select the “Add” button to add the devices to the zone or group selected.
Note
Panel inputs and loop devices may be mixed together in zones / groups to form many options for triggering the cause / effect requirements.
Note
Panel inputs and loop devices may be mixed together in zones / groups to form many options for triggering the cause / effect requirements.
The Principles of The Principles of Cause / Effect ProgrammingCause / Effect Programming
Control Groups
Group together panel
and loop inputs into
visible Led indication
zones (1-32) and hidden
control groups (33-255)
Allocation
Every device can be allocated
into 1 visible zone and 7
hidden control groups
Purpose
A group is used to collect loop
devices and panel inputs together
that will be used for specific
output purposes
Control Groups
Group together panel
and loop inputs into
visible Led indication
zones (1-32) and hidden
control groups (33-255)
Allocation
Every device can be allocated
into 1 visible zone and 7
hidden control groups
Purpose
A group is used to collect loop
devices and panel inputs together
that will be used for specific
output purposes Causes 2
Any amount of
available loop
devices
Causes 2
Any amount of
available loop
devices
Causes 1
Up to 248
Programmable
panel inputs via
additional 8-way
boards + 4 Virtual
Inputs using the
inbuilt software
timers
Causes 1
Up to 248
Programmable
panel inputs via
additional 8-way
boards + 4 Virtual
Inputs using the
inbuilt software
timers
Effects
Up to 248 Programmable
panel outputs such as
relays and 2 stage alarms + 4 virtual panel outputs from the inbuilt timers
Effects
Up to 248 Programmable
panel outputs such as
relays and 2 stage alarms + 4 virtual panel outputs from the inbuilt timers
Effects
Programmable loop
output devices such
as addressable relays
and loop sounders
Effects
Programmable loop
output devices such
as addressable relays
and loop sounders
Allocation
Each output device may
allocated to as many
groups as required
Conditions
The output conditions for each
group may be specified
differently for each output
device
Allocation
Each output device may
allocated to as many
groups as required
Conditions
The output conditions for each
group may be specified
differently for each output
device
The Principles of The Principles of Cause / Effect ProgrammingCause / Effect Programming
1 Group together all the panel and loop inputs determining what functions the groups will be required to do. For example call points may be allocated into zones for indication purposes and also all grouped together in to a hidden control group for specific cause/effect actions. Every input device may be allocated into 1 zone and 7 hidden control groups.
2 From the list of panel and loop outputs; for each output define the cause condition
3 Then select the control group of devices required to trigger the output
The Principles of The Principles of Cause / Effect OperationCause / Effect Operation
Panel Inputs
Loop Inputs
1-32 Visible Zones ____________
33-255 Control Groups
Output = Zone LED’s and Zone
number on LCD display
List of conditions that may trigger or
inhibit an output
Loop output devices and programmable panel
relays and alarm circuits
List of Panel and Loopoutputs
The List of Panel OutputsThe List of Panel Outputs
Selecting the Output
Select the required panel output and Ok to proceed
Selecting the Output
Select the required panel output and Ok to proceed
Panel Alarm Circuit Cause / EffectPanel Alarm Circuit Cause / Effect Step 1 Selecting Output Type
Use the drop down menu to select either Alert or Evacuate. The alert and evacuate outputs may be programmed in any order
Step 1 Selecting Output Type
Use the drop down menu to select either Alert or Evacuate. The alert and evacuate outputs may be programmed in any order
Step 2 Selecting Cause Conditions
Select the “Add Evac Cause” (or “Add Alert Cause” if showing)
Step 2 Selecting Cause Conditions
Select the “Add Evac Cause” (or “Add Alert Cause” if showing)
Note:
The “Copy Cause(s) Is useful for repeat operations
Note:
The “Copy Cause(s) Is useful for repeat operations
Step 4 Continuing
Repeat above steps for Evacuate causes.
Step 4 Continuing
Repeat above steps for Evacuate causes.
Step 5 Saving
Select “Save”.
Step 5 Saving
Select “Save”.
Panel Alarm Circuit Cause / EffectPanel Alarm Circuit Cause / Effect
Step 1 Selecting Local pane and or Network
Causes
This part of the programming shown continuing with local panel programming, the network programming is shown later.
Step 1 Selecting Local pane and or Network
Causes
This part of the programming shown continuing with local panel programming, the network programming is shown later.
Note:
A local cause is a cause from the panel being programmed.
A network cause is a cause from another panel on the network.
Note:
A local cause is a cause from the panel being programmed.
A network cause is a cause from another panel on the network.
List of Cause Conditions List of Cause Conditions
Note 1
This screen shows the list of cause conditions revealed when an “Alert” or “Evacuate” is selected as show on the previous slide.
Note 1
This screen shows the list of cause conditions revealed when an “Alert” or “Evacuate” is selected as show on the previous slide.
Step 1 Selecting the Condition
Select the condition required and “Double Click” to proceed.
Step 1 Selecting the Condition
Select the condition required and “Double Click” to proceed.
Note 2
Causes may be either Common or zonal.
If common causes are selected then the engineer will find the selected cause added to the evacuate or alert evacuate or alert cause list cause list being configured.being configured.
If zonal causes are selected then the If zonal causes are selected then the engineer will see the zone list as shown engineer will see the zone list as shown on the next slideon the next slide
Note 2
Causes may be either Common or zonal.
If common causes are selected then the engineer will find the selected cause added to the evacuate or alert evacuate or alert cause list cause list being configured.being configured.
If zonal causes are selected then the If zonal causes are selected then the engineer will see the zone list as shown engineer will see the zone list as shown on the next slideon the next slide
Allocating a Zone Allocating a Zone to a Cause Condition to a Cause Condition
Step 1 Selecting the Zone / Group
Select the zone/group required and “Double Click” to proceed.
Step 1 Selecting the Zone / Group
Select the zone/group required and “Double Click” to proceed.
Note
The engineer will find the selected zone and cause added to the cause list as cause list as shown on the Cause / Effect screen.shown on the Cause / Effect screen.
Note
The engineer will find the selected zone and cause added to the cause list as cause list as shown on the Cause / Effect screen.shown on the Cause / Effect screen.
Panel Alarm Circuit Cause / EffectPanel Alarm Circuit Cause / Effect
Information
The example here shows an alarm circuit output programmed to Alert (Pulsed) operation on any fire condition and Evacuate (Continuous) on zone 1 fire, Evacuate and Zone 33 where the call points have been programmed into various zones around the building for indication purposes and also hidden zone 33 where it is used for evacuation purposes.
Information
The example here shows an alarm circuit output programmed to Alert (Pulsed) operation on any fire condition and Evacuate (Continuous) on zone 1 fire, Evacuate and Zone 33 where the call points have been programmed into various zones around the building for indication purposes and also hidden zone 33 where it is used for evacuation purposes.
Note:
Select “Save” to save settings or “Exit” to leave the screen without saving.
Note:
Select “Save” to save settings or “Exit” to leave the screen without saving.
The List of Cause The List of Cause Conditions in DetailConditions in Detail
The List of Cause The List of Cause Conditions in DetailConditions in Detail
The List of Cause The List of Cause Conditions in DetailConditions in Detail
The List of Cause The List of Cause Conditions in DetailConditions in Detail
The List of Cause The List of Cause Conditions in DetailConditions in Detail
The List of Cause The List of Cause Conditions in DetailConditions in Detail
The List of Cause The List of Cause Conditions in DetailConditions in Detail
Common Disablement Operate Until Cause Clear
The selected output will be active whenever the General Disablement Indicator is on
Common Buzzer Operate Until Cause Clear
The selected output will be active when either the fire buzzer or the fault buzzer is on
Allocating a Loop Output DeviceAllocating a Loop Output Device
Selecting the Output for programming
Select the required output and then press Ok to proceed to the list of Cause Conditions
Selecting the Output for programming
Select the required output and then press Ok to proceed to the list of Cause Conditions
Loop Output Device Cause / EffectLoop Output Device Cause / Effect
Note 1
The engineer will find there is only on cause list per device and output channel (i.e. not a split screen) because it is not possible to send a pulsed data signal. But the sounder sounder controller channel B will provide a pulsed output
Note 1
The engineer will find there is only on cause list per device and output channel (i.e. not a split screen) because it is not possible to send a pulsed data signal. But the sounder sounder controller channel B will provide a pulsed output
Note 2
Proceed as per programming a panel sounder or relay output.
Note 2
Proceed as per programming a panel sounder or relay output.
Note 3
A programmable panel relay output will also display only one list option similar to that shown here.
Note 3
A programmable panel relay output will also display only one list option similar to that shown here.
Loop Output Device Cause / EffectLoop Output Device Cause / Effect
Note 1
The engineer will find there is only on cause list per device and output channel (i.e. not a split screen) because it is not possible to send a pulsed data signal. ( On a sounder or sounder controller channel B will provide a pulsed output).
Note 1
The engineer will find there is only on cause list per device and output channel (i.e. not a split screen) because it is not possible to send a pulsed data signal. ( On a sounder or sounder controller channel B will provide a pulsed output).
Note 2
Proceed as per programming a panel sounder or relay output.
Note 2
Proceed as per programming a panel sounder or relay output.
Note 3
A programmable panel relay output will also display only one list option similar to that shown here.
Note 3
A programmable panel relay output will also display only one list option similar to that shown here.
List of Cause Conditions List of Cause Conditions
Note 1
This screen shows the list of cause conditions revealed when an “Alert” or “Evacuate” is selected as show on the earlier slide.
Note 1
This screen shows the list of cause conditions revealed when an “Alert” or “Evacuate” is selected as show on the earlier slide.
Step 1 Selecting the Condition
Select the condition required and “Double Click” to proceed.
Step 1 Selecting the Condition
Select the condition required and “Double Click” to proceed.
Note 2
Causes may be either Common or zonal.
If common causes are selected then the engineer will find the selected cause added to the cause list as shown cause list as shown earlierearlier..
If zonal causes are selected then the If zonal causes are selected then the engineer will see the zone list as shown engineer will see the zone list as shown on the next slideon the next slide
Note 2
Causes may be either Common or zonal.
If common causes are selected then the engineer will find the selected cause added to the cause list as shown cause list as shown earlierearlier..
If zonal causes are selected then the If zonal causes are selected then the engineer will see the zone list as shown engineer will see the zone list as shown on the next slideon the next slide
Network Cause / Effect Programming Network Cause / Effect Programming
Note
When programming the cause / effect of output devices it is also possible to configure outputs to operate when triggered from other panels on the network
Note
When programming the cause / effect of output devices it is also possible to configure outputs to operate when triggered from other panels on the network
Step 2 Selecting Network Cause
Then select “Network Causes”
Step 2 Selecting Network Cause
Then select “Network Causes”
Step 1 Adding
From the Causes screen select “Add Cause”
Step 1 Adding
From the Causes screen select “Add Cause”
Network Cause / Effect Programming Network Cause / Effect Programming
Note
You will then be prompted to select the panelfrom which you want to receive information
Note
You will then be prompted to select the panelfrom which you want to receive information
Step 1 Selecting the Panel
Select the required panel by double clicking on it.
Step 1 Selecting the Panel
Select the required panel by double clicking on it.
Network Cause / Effect Programming Network Cause / Effect Programming
Note 1
You will then be see a list of the standard messages sent by each panel into the network called “Flags”.
Note 1
You will then be see a list of the standard messages sent by each panel into the network called “Flags”.
Step 1 Selecting the Message (Flag)
Select the required message (Flag)
Step 1 Selecting the Message (Flag)
Select the required message (Flag)
Step 2 Selecting the Condition
If required modify the message into the panel being programmed
Step 2 Selecting the Condition
If required modify the message into the panel being programmed
Note 2
See next slide for use of the “New” button
Note 2
See next slide for use of the “New” button
Selecting Select single, double or triple.
• Single - Any single flag will operate the output
•Double - Requires any 2 from the highlighted selection to operate the output
•Triple - Requires any 3 from the highlighted selection to operate the output
Selecting Select single, double or triple.
• Single - Any single flag will operate the output
•Double - Requires any 2 from the highlighted selection to operate the output
•Triple - Requires any 3 from the highlighted selection to operate the output
Network Cause / Effect Programming Network Cause / Effect Programming
Note
You can also create your own “Flags” if you require unusual conditions not found in the list of standard flags.
Note
You can also create your own “Flags” if you require unusual conditions not found in the list of standard flags.
Step 1 Further Options
If you need conditions other than the 520 standard then select “New” from the causes list shown on the previous slide.
You will then be presented with You will then be presented with some options some options
Step 1 Further Options
If you need conditions other than the 520 standard then select “New” from the causes list shown on the previous slide.
You will then be presented with You will then be presented with some options some options
Step 2 Completing
Select the option required and proceed as prompted. Select “OK” to complete the cause condition.
The condition will then be listed as The condition will then be listed as a new flag 521 upwards to select a new flag 521 upwards to select in the network Cause / Effect in the network Cause / Effect facility. facility.
Step 2 Completing
Select the option required and proceed as prompted. Select “OK” to complete the cause condition.
The condition will then be listed as The condition will then be listed as a new flag 521 upwards to select a new flag 521 upwards to select in the network Cause / Effect in the network Cause / Effect facility. facility.
Loop Output Device Cause / EffectLoop Output Device Cause / Effect
Information
The completed list of conditions for the operation and inhibits for the gas valve are now listed.
Any 2 detectors from zones 1,2,and 3 will operate the relay together with any call point (configured into various indication zones and also all configured into hidden control group 33) on the local panel. Any fire condition on panel number 3 will operate the relay.
The engineers key switch is configured into hidden control group 34 and when operated will indicate on the panel and prevent the relay from operating.
Information
The completed list of conditions for the operation and inhibits for the gas valve are now listed.
Any 2 detectors from zones 1,2,and 3 will operate the relay together with any call point (configured into various indication zones and also all configured into hidden control group 33) on the local panel. Any fire condition on panel number 3 will operate the relay.
The engineers key switch is configured into hidden control group 34 and when operated will indicate on the panel and prevent the relay from operating.
Making a Hex FileMaking a Hex File
Note
The engineer must make a Hex file before downloading to the panel. Any changes done to the configuration which are not then converted to a Hex file will not be downloaded.
Note
The engineer must make a Hex file before downloading to the panel. Any changes done to the configuration which are not then converted to a Hex file will not be downloaded.
Step 1 Hex Files
Select the panel required and then “Hex Files”.
Step 1 Hex Files
Select the panel required and then “Hex Files”.
Step 2 Selecting the Panel
Select “Make Hex File” . The programme will then convert the files to Hexadecimal for the panel and return to this screen.
Step 2 Selecting the Panel
Select “Make Hex File” . The programme will then convert the files to Hexadecimal for the panel and return to this screen.
The Print MenuThe Print Menu
Note
Accessing the Print function enables the engineer to print all the done for reference and approvals purposes.
Note
Accessing the Print function enables the engineer to print all the done for reference and approvals purposes.
Step 1 The List
Select the item required for printing and follow the on screen instructions.
Step 1 The List
Select the item required for printing and follow the on screen instructions.
Information
It is recommended that all printing is done from this screen and not from the specific programming screens because the files created in specific scrrens are temporary and not saved until the “Save” command is used.
Information
It is recommended that all printing is done from this screen and not from the specific programming screens because the files created in specific scrrens are temporary and not saved until the “Save” command is used.
Downloading (To the Panel) and Downloading (To the Panel) and UploadingUploading (From the Panel)(From the Panel)
Step 1
The programme will firstly prompt the engineer for the access code.
Step 1
The programme will firstly prompt the engineer for the access code.
Note 1
The display indicates the the progress of the download or upload
Note 1
The display indicates the the progress of the download or upload
Note 2
Allow up to 15 minutes for this operation. The software will continually check for errors and cannot be rushed
Note 2
Allow up to 15 minutes for this operation. The software will continually check for errors and cannot be rushed
Step 2
A list of files to “Download” to the panel will be revealed together with a “Download All”option. Alternatively the engineer may select the “Upload” function and then see a menu listing all the files which can then be uploaded from the panel. If only a small change has been made on the panel then only the required section of programming need be uploaded.
Step 2
A list of files to “Download” to the panel will be revealed together with a “Download All”option. Alternatively the engineer may select the “Upload” function and then see a menu listing all the files which can then be uploaded from the panel. If only a small change has been made on the panel then only the required section of programming need be uploaded.