Upload
others
View
5
Download
0
Embed Size (px)
Citation preview
HAL Id: hal-01308094https://hal.archives-ouvertes.fr/hal-01308094
Submitted on 27 Apr 2016
HAL is a multi-disciplinary open accessarchive for the deposit and dissemination of sci-entific research documents, whether they are pub-lished or not. The documents may come fromteaching and research institutions in France orabroad, or from public or private research centers.
L’archive ouverte pluridisciplinaire HAL, estdestinée au dépôt et à la diffusion de documentsscientifiques de niveau recherche, publiés ou non,émanant des établissements d’enseignement et derecherche français ou étrangers, des laboratoirespublics ou privés.
An innovative coupling between column leaching andoxygen consumption tests to assess behavior of
contaminated marine dredged sedimentsJulien Couvidat, Mostafa Benzaazoua, Vincent Chatain, Fan Zhang, Hassan
Bouzahzah
To cite this version:Julien Couvidat, Mostafa Benzaazoua, Vincent Chatain, Fan Zhang, Hassan Bouzahzah. An innova-tive coupling between column leaching and oxygen consumption tests to assess behavior of contam-inated marine dredged sediments. Environmental Science and Pollution Research, Springer Verlag,2015, 22 (14), pp.10943-10955. �10.1007/s11356-015-4323-z�. �hal-01308094�
1
An innovative coupling between column leaching and
oxygen-consumption tests to assess behavior of
contaminated marine dredged sediments
Julien Couvidat1, Mostafa Benzaazoua1,2, Vincent Chatain1,*, Fan Zhang1, Hassan Bouzahzah2
1 Université de Lyon, INSA-Lyon, Laboratoire de Génie Civil et d'Ingénierie
Environnementale LGCIE, 20 avenue Albert Einstein, F-69621 Villeurbanne, France
2 IRME, UQAT, 445 Boul. de l’Université, Rouyn-Noranda, J9X 5E4 Canada
* Phone: +33 (0)4 72 43 81 90 - Fax: +33 (0)4 72 43 87 17 – E-mail: [email protected]
Abstract
Purpose: Contaminated dredged sediments are often considered hazardous wastes, so they have to be adequately
managed to avoid leaching of pollutants. The mobility of inorganic contaminants is a major concern. Metal
sulfides (mainly framboïdal pyrite, copper and zinc-sulfides) have been investigated in this study as an important
reactive metal-bearing phase sensitive to atmospheric oxygen action.
Methods: An Oxygen Consumption-Test (OC-Test) has been adapted to assess the reactivity of dredged
sediments when exposed to atmospheric oxygen. An experimental column set-up has been developed allowing
the coupling between leaching and oxygen consumption test to investigate the reactivity of the sediment.
Results: This reactivity, which consisted of sulfides oxidation, was found to occur for saturation degree between
60 and 90% and until the 20th testing week, through significant sulfates releases. These latter were assumed to
come from sulfides oxidation in the first step of the test, then probably from gypsum dissolution. Confrontation
results of OC-Test and leachates quality shows that Cu was well correlated to sulfates releases, which in turn
leads to Ca and Mg dissolution (buffer-effect). Cu, and mostly Zn, was associated to organic matter,
phyllosilicates and other minerals through organo-clays complexes.
Conclusions: This research confirmed that OC-Test originally developed for mine tailings could be a useful tool
in the dredged sediment field which can allow for intrinsic characterization of reactivity of a material suspected
to readily reacting with oxygen and for better understanding of geochemical processes that affect pollutants
behavior, conversion, and transfer in the environment.
Keywords: dredged marine sediment, oxygen consumption test, sulfides, trace metals,
leaching, oxidation, organic matter
2
1. Introduction
Management of contaminated dredged sediment is a requirement of harbors administrators and authorities,
which are in charge of the dredging operations. Up to 18.6 million ton of sediment (in dry matter) have been
dredged in France (metropolitan and overseas) in 2010, 33.56 million tons in 2009, and 23.2 million tons in 2008
(Le Guyader 2011; Le Guyader 2013). Once extracted from their original environment, sediments are considered
as waste materials that have to be adequately managed accordingly to existing regulations (European Council
2002; French Official Journal 2007). Marine sediments are composed mainly of minerals (quartz, various
silicates, carbonates, iron and manganese oxy-hydroxides, and sulfides) as well as organic matter (OM).
Contaminants are mainly sourced from urban contamination, industrial activities as well as nautical activities.
Inorganic pollutants (Cu, Zn, Pb, Cr, Hg, As…) are particularly of concern due to their ubiquitous presence and
their accumulation within sediments. Organometallics, mainly as tin compounds, and organic pollutants are also
of significant concern. All those compounds are likely to be harmful towards the environment as well as human
health even at low levels, and frequently encountered at various levels in marine sediments (Caplat et al. 2005;
Casado-Martínez et al. 2009; Chatain et al. 2013a; Dı́ez et al. 2002; Eek et al. 2008; Jones and Turki 1997; Lions
et al. 2010; Mamindy-Pajany et al. 2012; Ribecco et al. 2011; Staniszewska et al. 2011). Sulfides minerals are
likely to control the mobility of trace metals in anoxic layers as Cu or Zn (Morse and Luther Iii 1999; Salomons
et al. 1987; Ye et al. 2011). Metal mobility depends on several processes, as discrete sulfide phases precipitation,
complexation with bisulfides, polysulfides or OM, adsorption or coprecipitation within iron sulfides (Huerta-
Diaz et al. 1998). Their immobilization into metallic sulfides in anoxic environment is not only controlled by
thermodynamic parameters, but also depends on ligand exchange reaction kinetic and redox reaction pathways.
For instance, Pb, Zn, and Cd form MeS (or MeS2) phases, whereas Co or Ni are rather incorporated into pyrite
(Morse and Luther Iii 1999). Furthermore, it was stated that pyrite (FeS2) and iron monosulfide (FeS) play a
central role in the iron and sulfur cycles in marine sediments (Schippers and Jørgensen 2002).
In fact, sulfides are known as reactive minerals very susceptible to the redox potential. Dredging and land-
storing induces oxygen diffusion while water desaturation increases. Molecular oxygen is the main oxidant of
reduced sulfur species in oxic environment, as shown in the equation (Eq.1) of pyrite oxidation by molecular
oxygen and water (Lowson 1982).
2FeS2 + 7O2 + 2H2O → 2Fe2+ + 4SO42− + 4H+ (Eq. 1)
Oxidation of sulfides can occur and lead to inorganic contaminants release, even at neutral pH (Salomons et al.
1987). In sulfide bearing sediments, the framboïdal pyrite is considered as the most common form of pyrite in
anoxic sediments as well as the most reactive (Pierret et al. 2000). Usually in marine sediments, pyrite
concentrations are under 1 wt.% (Lowers et al. 2007; Schenau et al. 2002), and up to 20 wt.% in some rare cases
(Pierret et al. 2000). Sulfides clearly play a central role towards trace metals mobility, and their reactivity is a
key parameter towards assessment of the environmental impact of contaminated sediments. Most studies in the
literature focused on sediment geochemical behavior through leaching tests, according to current regulations
(Caplat et al. 2005; Chatain et al. 2013a; Chatain et al. 2013b; Guevara-Riba et al. 2004; Prokop et al. 2003;
3
Sundaray et al. 2011). Knowledge about parameters linked to this sulfide reactivity should be improved, given
the challenges for better management of contaminated dredged sediments. Monitoring of parameters such as pH,
oxido-reduction potential (ORP), or trace and major metal concentrations have been promoted during leaching
test (Cappuyns and Swennen 2008). Moreover, it is worth mentioning that there are other approaches usually
used in the characterization of sulfidic materials. For instance, some mining research scientists used during the
last two decades an oxygen consumption-test (OC-Test) to assess the acid mine drainage (AMD) potential of
sulfides-rich wastes (Demers et al. 2009; Elberling et al. 2003; Elberling and Nicholson 1996; Mbonimpa et al.
2003; Ouellet et al. 2006). In this study, the authors propose to adapt the OC-test to dredged sediment
characterization in order to better understand the geochemical interactions between sulfides, OM and oxygen.
In this context, the main objective of the study is to assess the reactivity and geochemical behavior of dredged
sediment by the use of an innovative experimental column set-up allowing the coupling between leaching test
and OC-Test. The authors propose to link the oxygen consumption (OC) due to sulfides and OM oxidation to the
quality of the leachates (trace metals, sulfates …) released during a column leaching test on a contaminated
harbor sediment.
2. Material and methods
2.1. Sampling, treatment, and preparation of sediment
The sediment used was dredged in a harbor located in the south of France. It was sampled with a mechanical
shovel and sieved at 20mm. This marine sediment was stored for 5 years to undergo a natural weathering after a
short aeration pretreatment. Prior to characterization, the sediment was homogenized by quartering and stored at
4°C in darkness.
2.2. Analytical methods
2.2.1. Sediment characterization
The sediment was characterized for particle size distribution (PSD), total sulfur and carbon, specific gravity
(Gs), chemical composition, non-organic sulfur speciation and total organic carbon (TOC). PSD was determined
by laser diffraction (Malvern Mastersizer 2000G) after sieving of the sediment at 1mm. During the PSD analysis,
the ultrasounds were applied for 1 min to allow aggregates breakdown. Total sulfur and total carbon were
determined by induction furnace analyser (ELTRA CS-2000). Gs of each sample was measured with an helium
gas pycnometer (Micromeritics Accupyc 1330). Chemical composition was determined by inductively coupled
plasma atomic emission spectroscopy (ICP-AES, Perkin Elmer Optima 3100 RL) after a HNO3/Br2/HF/HCl
digestion. Determination of non-organic sulfur speciation was realized by HCl extraction according to a Sobek
method (Sobek et al. 1978). Only HCl-extractable sulfur are determined, mostly sulfates and amorphous sulfides,
giving by difference with total sulfur the amount of sulfur under crystallized sulfides forms and non-extractable
4
organic sulfur. Content in OM was determined by TOC through sample combustion within a furnace heated to
680°C. The released gas was then analyzed with non-dispersive infrared gas apparatus.
The mineralogy of samples was determined by X-ray diffraction (XRD) (Bruker AXS D8 advance) equipped
with a copper anticathode, scanning over a diffraction angle (2θ) range from 5° to 70°. Scan settings were 0.02°
2θ step size and 4s counting time per step. The DiffracPlus EVA software (v.9.0 rel.2003) was used to identify
mineral species and the TOPAS software (v 2.1) implementing Rietveld refinement was used to quantify the
abundance of all identified mineral species (Young 1993). The absolute precision of this quantification method is
of the order of ±0.5-1% (Bouzahzah et al. 2008; Raudsepp and Pani 2003). The samples mineralogy
identification was completed by optical microscopy observations. Polished sections prepared with bulk samples
(sediment impregnated within an epoxy resin) were observed by reflected light microscopy (Zeiss Axio
Imager.M2m). The chemical composition of the individual minerals (stoichiometry) was determined using a
scanning electron microscope (Hitachi S-3500N) equipped with an Energy Dispersive Spectrometer (EDS,
Silicon Drift Detector X-Max 20 mm², Oxford) operated under the INCA software (450 Energy). The operating
conditions were 20keV, ~100 µA and 15 mm working distance.
2.2.2. Leachates analysis
Leachates were immediately prepared after their recovery from column test for chemical analysis. All recovered
leachates were limpid and were filtrated through Minisart 0.45 µm syringe filters. To improve the interpretation
of geochemical results and investigate the release patterns or involved reactions into the leaching of trace metals,
parameters such as pH, ORP and conductivity, some anions (Cl- and SO42-), major elements (Ca, Mg, Mn, …),
and dissolved organic carbon (DOC) are monitored into leachates (Cappuyns and Swennen 2008). Leachates
were analyzed for trace elements and major dissolved metals by ICP-AES after acidification with 2% HNO3.
Sulfates and chlorides were analyzed using an ionic chromatography (Dionex DX320 HPIC®). DOC
concentration was determined by a total organic carbon analyzer (Shimadzu TOC 5000A®). pH, ORP and
conductivity measurements were done immediately after each column rinsing and leachates recovery. pH and
conductivity were measured with an Epoxy pH Ag/AgCl electrode (Fisherbrand 90437BNC) and an epoxy
conductivity electrode (Consort SK10T) on a pH/mV meter (Consort C3020), and ORP was measured using a
Radiometer Analytical® combined platinum electrode [Pt/Ag/AgCl, +197mV vs. Normal Hydrogen Electrode
(NHE)].
2.3. Leaching column and Oxygen Consumption-Test
Highly reactive minerals when exposed to oxidizing environment may lead to pollution by releasing acidity and
metals. In this context, a column leaching test was used to assess the leachability of the studied sediment. The
cell column is made with transparent Plexiglas® of approximately 10.1 cm diameter and 25.4 cm height (Fig. 1).
Several openings are located around the chamber allowing probes and fluid inlet and outlet. The top of the
device is a removable cap with a large opening for the oxygen sensor. A plastic plate pierced with low diameter
holes (2mm) is set in the lower third of the chamber, to fill with the sample. Geotextile film is inserted between
the sample and the plate. A drain is available in the bottom of the chamber for flushing the device. Sediment was
5
placed into the chamber in a manner to have same porosity (n=0.6) as its state when deposited in the field
(Capilla et al. 2006). Testing consisted of 15 leaching cycles. The cell flushing was conducted each 14 days by
addition 500mL of deionized water at the top of the column. Leaching behavior of the sediment was investigated
in parallel with the OC-Test as shown in Fig. 1. An oxygen sensor (Teledyne Analytical Instruments R-17A) is
inserted at the top of the sealed column. The sensor measurement principle is based on an electrochemical
galvanic battery, using the half-cell Pb/PbOOH to reduce oxygen. Consumption of oxygen by the sensor itself is
therefore considered as negligible. The induced current of the reaction is directly proportional to the partial
pressure of oxygen in the gas phase; the sensor generates an output signal in form of voltage every 5 seconds.
Accuracy of the sensor is 0.1% in oxygen concentration. A data-logger (OMEGA Engineering OM-CP-
QUADVOLT-100MV) is connected to the sensor and converts the output signal which is recorded by software
on a computer.
2.3.1. Oxygen flux assessment
Oxygen Consumption test is a method that allows linking the products of the oxidation reaction analyzed within
the leachates (i.e., sulfates and trace metals), with the main oxidant which is the oxygen (Lowson 1982). This
approach was developed for mine tailings to assess their reactivity by measuring the consumption rate of air-
oxygen (Elberling and Nicholson 1996; Elberling et al. 1994; Mbonimpa et al. 2012).
Essentially, the method consists in measuring the oxygen concentration decreases in an air filled chamber
located above the column during a short time period. The decrease in O2 concentration can be converted into an
oxygen flux by using Fick’s Laws. This method was initially designed for determining reaction rates of sulfide
tailings. The consumption of oxygen in the chamber can be related to the reactivity of sulfides through oxidation
with molecular oxygen. The relation between oxygen flux through the sediment and the decrease in oxygen
concentration in the sealed chamber is based on fundamental gas diffusion laws (in this study, only Fickian gas
transport mechanisms are considered). Solving Fick’s second law expressed with a first-order kinetic reaction
term for steady state flux and specified boundary conditions gives the following equation (Eq. 2) for the flux at
the cover surface (Elberling et al. 1994):
𝐹𝐿 = 𝐶0(𝐾𝑟𝐷𝑒)1
2 (Eq. 2)
where Kr [T-1] is the first-order reaction rate coefficient for the system, De [LT-2] is the effective diffusion
coefficient and C0 [ML-3 or MolL-3] is the atmospheric concentration of oxygen. Solving the continuity equation
(which reflects the oxygen being consumed in the head space) for the initial condition C=C0 at t=0, the following
solution is obtained (Eq. 3):
ln(𝐶/𝐶0) = −𝑡(𝐾𝑟𝐷𝑒)
1
2 (𝐴
𝑉)
(Eq. 3)
where A [L2] and V [L3] are the area and the volume of the source reservoir, respectively. The slope of the plot of
ln(C/C0) versus time gives the value of (KrDe)1/2 when A/V is known. This term is substituted into Eq. (2) to
evaluate the flux of oxygen at the surface. The standard OC test requires only a small change in oxygen
concentration (2 to 3% O2) in the headspace over a 1- to 3-hour(s) period so that changes in oxygen
6
concentration within the pore spaces are insignificant during the testing period to comply with the interpretation
assumption of steady state flux. Details of the interpretation method for the standard OC method are given in
(Elberling et al. 1994) and (Mbonimpa et al. 2003).
2.3.2. Influence of saturation degree on sulfide reactivity
Sulfides minerals can be oxidized when exposed to water and O2 action (Eq. 1). The degree of saturation (Sr)
related to water content of samples has an important impact on sulfides reactivity (Bouzahzah et al. 2012;
Mbonimpa et al. 2003). In fact, a low Sr (low water content) reduces the water availability reducing the oxidation
reaction, while a high Sr reduces the oxygen availability due to the low solubility of O2 in water (Ouangrawa et
al. 2009).
A preliminary test was performed to study the sensitivity of the OC-Test to the Sr of sediments, and to provide
the optimal duration of cycles (Fig. 2). The optimal Sr is comprised between 70 and 90%, with a maximum at
80%. Moreover, the Sr decrease from 90 to 70% took 2 weeks. According to those results, OC-Tests were carried
out every 14 days, 12 days after the previous flush.
3. Results
3.1. Sediment characterization
The physical and chemical properties of the studied sediment are presented in Table 1. The measured Gs is 2.55
g/cm3, close to Gs of quartz and carbonate minerals which are usually the predominant constituents of sediments.
PSD shows that the sediment can be classified as a fine silty sediment, with 50% of the particles under 20µm
(D50 = 19.24 µm). Organic matter is an important constituent of the sediment. Indeed, TOC is about 6.3%, in the
range of usual values for marine sediments (Tessier et al. 2011). The total sulfur content is about 2 wt.%, where
51% extractable with HCl would represent mostly sulfates minerals as gypsum (except barite), and potential
reactive sulfides, the remaining 49% would represent mostly well-crystallized sulfides as pyrite, and the
unassessed pool of organic sulfur.
Trace metals are investigated in the whole sediment (Table 2). Some trace metals, as Cu, Pb or Zn, are monitored
in dredged sediments according to French regulation (French Official Journal 2007), relative to threshold levels
to be taken into account for the analysis of a marine sediment sea rejection. Two threshold levels N1 and N2 are
determined through this regulation. If the assessed sediment has one trace metal over the N2 level, it is treated as
“contaminated sediment”, which means it cannot be rejected into the sea but needs to be managed and/or treated
in a proper way. Iron (Fe) is related to some of the most important metal key phases in marine sediments, e.g.
oxy-hydroxides and sulfides. The Fe is not concerned by regulation, and is usually found in the same extent that
it is found in this marine sediment. Cu, Pb and Zn which are concerned by French regulation were measured in
leachates. They are found in the sediment at very high levels, above ten times higher than N2 threshold level for
copper, five times for the two others.
The sample mineralogy was determined by X-Ray diffraction (Table 3) and shows that 34.6 wt.% of minerals are
silicates (19.3 wt.% of clays and 15.3 wt.% of quartz). The carbonate minerals represent 52.5 wt.% of the
7
sample, with 13.6 wt.% of dolomite and 38.9 wt.% of calcite. Pyrite is the only crystallized form of sulfide
significantly found in the sediment, which accounts for 2 wt.% of the quantified minerals. In addition, 5 wt.% of
gypsum is determined as well as about 1.1 wt.% of iron oxide (magnetite). Halite (0.8 wt.%) is also identified by
XRD as some frequent minerals in marine sediment.
Optical and scanning electron microscopic (SEM-EDS) observations show well-preserved pyrite and some
framboïdal ones in particular (Fig. 3a). A ferrous oxide layer is covering surface of massive pyrites, suspected to
act as a protective layer (passivation) (Fig. 3b). Iron oxide layer seems to be Goethite, or Lepidocrocite,
according to Fe/O ratio. Both massive and framboïdal pyrite are surrounded by clays and OM aggregate,
containing calcite, quartz, and traces of copper and zinc. Sulfides might have been preserved from oxidation
either by the protective passivation layer of iron oxy-hydroxides, and the organo-clays aggregate (Lions et al.
2010).
3.2. Column leaching test
3.2.1. Conductivity, pH and Eh parameters of leachates
The column leaching test was conducted over 30 weeks, with a flush every 2 weeks. Chemical parameters of
recovered leachates are presented in Fig. 4. Initial conductivity was high at about 6.4 mS/cm, and decreased to
1.1 mS/cm after 16 weeks (Fig. 4a). In the early stage, the fast release of soluble products occurred, and then
decreased strongly. The same behavior was observed for chlorides, which concentration decreased from 400 to
10 mg/kg (halite dissolution). During the column leaching test, leachates presented stable pH values around 7.5
(Fig. 4b). ORP oscillated around +500 mV/SHE for the 7 first cycles and then reached a second state around
+370 mV/SHE until the end of the test.
3.2.2. Chemistry of leachates
Sulfates content in the leachates are presented in Fig. 5a. Sulfur total depletion during the 30 testing weeks was
of 16%. Sulfates in leachates were highly concentrated especially at the beginning of the test (1200 mg/kg DM).
Concentrations decreased to reach a plateau around 400 mg/kg DM between the 16th and 20th weeks. This
leachable sulfur fraction would be linked either the oxidation of accessible framboïdal pyrites, or the dissolution
of soluble sulfates mineral phases. Ca and Mg are significantly released during the first weeks of the leaching
test (Fig. 5b). Their respective concentrations were 250 and 150 mg/kg DM at the beginning of the test, and
decreased throughout weeks to reach a stable value around 130 and 25 mg/kg DM respectively. Accordingly to
the sediment mineralogy, Mg and Ca are expressed mainly as dolomite and calcite. Ca is also associated to
gypsum whose dissolution would cause the release of Ca into recovered leachates. Dolomite and calcite are
responsible for buffering effect. As previously observed, it can be expected that leaching of those minerals
reflects the acid (H+) neutralization following metallic sulfides oxidation. Carbone was also investigated on its
dissolved forms into leachates. DOC has roughly the same behavior as chlorides which rapidly decreased after
the first testing cycles at 49 mg/kg DM to 8 mg/kg DM at 5th cycle and then reached a plateau around 5 mg/kg
DM.
8
Cu, Fe and Zn concentrations into leachates are presented in Fig. 6. Pb was under the detection limit of ICP-AES
on all analyzed leachates and it is not discussed in this section. Pb’s leachability is known to be very low in a
range of pH between 6.5 and 12, and it is much more sensitive to acidic pH (Chatain et al. 2013b; Trefry and
Metz 1984). Contrary to Pb, and as observed in literature (Dold and Fontboté 2002; Warwick et al. 1998), Zn
was released during the whole experiment with concentrations between 0.1 and 0.4 mg/kg. Moreover, Cu
decreased progressively from 0.2 to 0.01 mg/kg DM. Fe was released at very small concentrations indicating a
probable precipitation of fresh Fe-oxi-hydroxides. Other trace metals (arsenic, chromium, manganese) were
mostly under detection limit.
3.3. Oxygen consumption test
Contrary to mine tailings, ln(C/C0) versus time plot provided a hyperbolic curve instead of a straight line, due to
the weaker reactivity of sediments. A punctual reactivity is therefore taken into account to calculate the oxygen
flux (FL), represented by the slope of the curve (ln(C/C0) = f(t)) which is linear between 0 and 2 minutes. O2
consumption was realized over the 30 weeks of the testing (Fig. 7). Important oxidation occurred at the
beginning of the test (between the second and the eighth weeks) with more than 100 mol(O2).m-2.s-1. This O2
consumption then gradually decreased to reach zero consumption from the 20th week until the end of the test.
The measured Sr during every O2 consumption test varied roughly between 60 and 70% and no correlation was
observed between the decrease of O2 consumption and Sr.
4. Discussion
The objective of this study was to assess the reactivity and the geochemical behavior of the sediment by the use
of an experimental column set-up, with the coupling between leaching test and OC-Test. Elucidation of this
geochemical behavior depends on essential factors, environmental reagents, mineralogy of the sediment and
products monitored into leachates, whose interactions are summarized in a schema (Fig.8). This set-up allows
looking into main processes at work in the sediment coming from those interactions, which will be discussed
afterward.
4.1. Oxygen consumption behavior
The fast decrease of oxygen consumption observed during the first cycles of testing let to make some
interrogations. Firstly, OM is the major difference between mine tailings and marine sediments. Moreover
oxidation of OM in aged marine sediment is considered to have minor or even no impact on OC, which is
indicated by DOC and OC behaviors (Fig. 8). DOC has quickly reached a plateau after two cycles, whereas OC-
Test has showed important variations until 5th cycle. And despite a possible residual oxidation of OM until the
end of the test, no OC is monitored. Most of the reactive OM has been oxidized all along the years of storage.
The remaining, regardless of its importance, is deeply linked to the sediment properties through aggregation and
has a very slow microbial oxidation rate towards sulfides oxidation (Mtambanengwe et al. 2004; Puget et al.
2000). More generally, it was thought that differences in kinetic of the respective reactions, e.g. sulfides
oxidation and organic matter mineralization, lead to observations at different timescale.
9
The Column leaching test was designed for 4 to 6 months in order to assess sulfides oxidation. The oxygen
consumption progressively decreased after 10th week to reach zero at 20th week until the end of the test. In fact,
this reduction in OC-Test may be attributed to a sulfide oxidation inhibition. Aggregation of sulfides with clays,
OM and other minerals, as seen by SEM observations (Fig. 3a), can act as a protective layer towards oxygen.
Moreover, passivation of sulfides’ surface by precipitation of freshly produced Fe-oxy-hydroxides is considered
to contribute to the decrease of OC during the testing (as seen in Fig. 3b). After the sample dismantling on
column set-up, it was observed that the top layer of the sediment was hardened, reminiscent of the Hardpan
phenomenon currently happening to sulfidic mine wastes (Blowes et al. 1991; Graupner et al. 2007). The
induced decrease of oxygen consumption and diffusion into the sediment might be furthered by the diminution
of the oxidant activity (ORP), as observed.
4.2. Oxidation/neutralization processes
Sulfates are oxidation products of sulfides, and though directly linked to oxygen consumption (Fig. 8). This
reaction leads to acidity production (according to Eq. 1) which is mostly neutralized by carbonates (Eq. 4):
𝐶𝑎𝐶𝑂3 + 𝐻+ → 𝐻𝐶𝑂3− + 𝐶𝑎2+ (Eq. 4)
Thereby, oxidation is followed by concomitant production of neutralization products, such as Ca, Mg, and
dissolved inorganic carbon (DIC) (Fig. 8). In mine tailings field, the geochemical behavior of a sample is
graphically characterized by an oxidation-neutralization curve between neutralization cations (e.g. Ca, Mg, and
Mn) and sulfates (Benzaazoua et al. 2004). This is particularly used to determine the long term acid-generating
potential of hazardous tailings. In our case, by plotting Ca+Mg versus released sulfates, a proper alignment with
good correlation is obtained (Fig. 9a). Mn is not considered because its concentrations into leachates are under
the detection limit of ICP-AES. A good correlation between Ca+Mg versus sulfates illustrates the oxidation-
neutralization effect that occurred in anoxic dredged sediment, as well as in mine tailings. Furthermore, sulfates
leaching behavior is roughly similar with those of OC-Test, Eh, Ca, and Mg leachates analysis, with a high
plateau from the beginning of the test until 10th week (600 to 1300mg/kg DM), and a lower one after (about
400mg/kg DM). This change in sulfates leaching behavior could be explained by two different origins of
sulfates: oxidation of sulfides first according to sulfides’ oxidation equation (Eq. 1) and OC-Test, and dissolution
of sulfates mineral phases after.
Dissolution of sulfates compounds might release sulfates ions in leachates and participate to the observed
correlation, when OC is over. Thus, according to XRD observations, the release of sulfates and calcium could be
attributed to gypsum (Fig. 8). Indeed, Gypsum dissolution is known to be influenced by pH, temperature or
competitive ions. Into distilled water, its maximum solubility is 2.85 g/L (16.6 mmol/L) between 30 and 40°C,
reaching 3.8 g/L (22.1 mmol/L) into seawater. Gypsum solubility decreases in presence of common ions Ca2+
and SO42- (Tanji 1969; Visconti et al. 2010).
Sulfates released in the first plateau exceed the theoretical concentrations of solubilized gypsum, even in the case
of high ionic strength leaching solution without any competitive ions. In fact, after placing the sediment in the
column for testing, reactive sulfides are oxidized and concomitant oxidation-neutralization products are released
10
into pore water. Dissolution of gypsum in those conditions might be not furthered, but if it occurred, dissolved
concentrations released are much lower than those released by the sulfide oxidation. When oxidation decreased,
oxidation-neutralization products have lessened. Dissolution of gypsum could have increased, or at least became
more important than oxidation products, as other authors are observing same behavior for gypsum for column
leaching test with distilled water (Lions et al. 2007). This hypothesis can be seen graphically by calculating
molar ratios of calcium versus sulfates, and calcium versus magnesium (Fig.9b). Theoretically, oxidation-
neutralization reactions produce a Ca versus sulfates ratio of 0.5, whereas in the case of a congruent dissolution
of gypsum it must be 1. Moreover, according to a major competition between calcite and dolomite towards
neutralization, Ca versus Mg ratio has to be close to 1 in the first case, and much higher for dissolution of
gypsum.
By plotting those ratios versus time, Ca versus sulfates ratio is about 0.5 at the beginning, and close to 0.9 at the
end of the testing. Ca versus Mg ratio is also close to 1 firstly and then reaches 7, which supports the fact that
sulfates are mostly released from sulfides oxidation in the first part of the test. With the decrease of oxidation,
gypsum (or other sulfates minerals) dissolution might become the major source of sulfates.
pH stabilization around 7.5 and the Ca and Mg content into leachates are the main direct observation of the
buffer effect. Ca releases are increasingly found into leachates until the 10th week, issued from dissolution of
carbonates minerals, calcite and dolomite, as neutralization response to acidity generated by sulfides oxidation.
Ca concentrations then decreased to reach a plateau. Mg decreased gradually to reach a plateau after 14 th week. It
is in accordance with the lessening of oxygen consumption observed around the 10th week, linked to the decrease
of the sulfides oxidation. Dissolved inorganic carbon into leachates is constantly found under 6 mg/kg DM
throughout the testing. Carbonates precipitation must occur as pH remains neutral-basic into the sediment.
4.3. Trace metals behavior
According to the sediment’s mineralogy, Fe appears mainly associated to clays minerals, (chamosite and illite),
sulfides (mostly pyrite) and magnetite. Pyrite is the most probable leaching phase for Fe in the column-leaching
test conditions, as physicochemical conditions do not particularly enhance reduction of iron oxides phases. Fe is
very sensitive to redox potential and pH, and it precipitates under hydroxide form (Fe(OH)3) in neutral-oxidant
environment, as this form predominates over pH 6 for Eh between 0 and 0.75V (Pourbaix et al. 1963).
Released concentrations of Cu in leachates are well correlated to oxygen consumption, and decrease constantly
to reach a plateau when no oxidation is monitored. Cu is also found to be well correlated with released sulfates,
especially in the first part of the test (Fig. 10a), and likewise DOC at the same time (Fig.10b). In fact, Cu is
known to be linked to organic matter and sulfides (Caplat et al. 2005; Förstner et al. 1981). In the second part of
the test, sulfates, Cu and DOC reached a plateau. Cu probably comes from the organo-clays aggregate observed
in SEM picture (Fig. 3a and 3b), which is associated with minerals and organic matter, as well as trace metals as
Cu and Zn.
Zn concentrations are more important into leachates than Cu during the whole test. It was reduced by half during
the second part of the testing, after 14th week. Zn well correlates with sulfates and DOC (Fig. 10a and b). In case
of sulfidic origins of Zn, Fe-oxi-hydroxides phases and phyllosilicates have been found to reduce Zn mobility
after sulfides oxidation (Isaure et al. 2002; Isaure et al. 2005). Moreover, Zn2+ is a stable divalent cation which
11
has a strong affinity for OM (Sauvé et al. 2000), as well as carbonates (Chatain et al. 2013b). Those phases could
explain Zn leaching, even at neutral pH. According to SEM pictures and diffuse leaching behavior, Zn is more
probably associated to organo-clays aggregates.
5. Conclusion
Sulfides have been investigated in this sediment. Pyrite is found to be the major crystallized sulfides, still present
despite aeration pretreatment. High reactivity of sulfides when exposed to atmospheric oxygen in sedimentary
matrix was assessed with an experimental system. This reactivity was found to occur for saturation degree
between 60 and 90%. A column leaching test coupled with an Oxygen Consumption-Test was carried out to
better understand the behavior of dredged marine sediment when exposed to ambient air (Fig. 8). Oxygen
consumption was found to occur firstly for some minutes when pilot is closed to run the test, and oxygen
consumption was compared on the basis of the 2 first minutes.
This method showed a variation of oxidation activity which could correlate to the leaching behavior. We found
that organic matter should have very little influence on oxygen consumption at such timescale, by monitoring
DOC into leachates. Fe is suspected to mostly precipitate after oxidation of iron sulfides phases, whereas Cu
readily leached from sulfides phases when oxidation occurred, and with dissolved organic matter then. Zn is
associated to organo-clays complexes, which contained other reactive minerals as carbonates, and leached during
the whole test. Sulfates are oxidation products of sulfides, and the acidity generated by the oxidation reaction is
neutralized by carbonates minerals which released Ca and Mg ions as neutralization products into leachates.
Sulfates released after the end of oxidation could be dissolution products of sulfates minerals phases, such as
gypsum, favored by the decrease of competitive sulfates and calcium ions into pore water.
Despite the weathering of the material, and the oxidizing and natural leaching conditions to which it was
subjected, this sediment was able to show a reactive leaching pattern such as oxidation-neutralization
phenomenon. Storage and climatic conditions lead to modification of the physicochemical structure of the
sediment, surface sealing at oxygen and water, inducing a decrease of Eh and leachability inside the batch. But,
we notice that this apparent stabilization can be seen as a metastable state and modifications as sampling,
dumping, staggering, may lead to more or less temporary reactive behavior, and subsequent leaching of
hazardous substances, as it was stated before (Lions et al. 2007). This OC-Test originally developed for mine
tailings was thus found to be a useful tool in the dredged sediment field, prior to assess the reactivity of a
material suspected to readily react with oxygen.
6. Acknowledgment
The authors are grateful to EEDEMS (French research network on waste and polluted materials management) for
experimental support. Author’s acknowledgments also go to University of Quebec (UQAT) for their support in
the mineralogical and physicochemical analyses.
12
7. Conflicts of interest
The authors declare that there is no conflict of interests regarding the publication of this paper.
8. References
Benzaazoua M, Bussière B, Dagenais AM, Archambault M (2004) Kinetic tests comparison and interpretation
for prediction of the Joutel tailings acid generation potential Environmental Geology 46:1086-1101
doi:10.1007/s00254-004-1113-1
Blowes DW, Reardon EJ, Jambor JL, Cherry JA (1991) The formation and potential importance of cemented
layers in inactive sulfide mine tailings Geochimica et Cosmochimica Acta 55:965-978
doi:http://dx.doi.org/10.1016/0016-7037(91)90155-X
Bouzahzah H, Benzaazoua M, Bussière B (2012) Modification and automation of the humidity cell test protocol
to favor tailings reactivity Proceedings of the 9th ICARD, Ottawa, ON, Canada
Bouzahzah H, Califice A, Benzaazoua M, Mermillod-Blondin R, Pirard E Modal analysis of mineral blends
using optical image analysis versus X ray diffraction. In: Proceedings of International Congress for
Applied Mineralogy ICAM08, Brisbane, Australia, 2008. AusIMM,
Capilla X, Schwartz C, Bedell J-P, Sterckeman T, Perrodin Y, Morel J-L (2006) Physicochemical and biological
characterisation of different dredged sediment deposit sites in France Environmental Pollution 143:106-
116 doi:http://dx.doi.org/10.1016/j.envpol.2005.11.007
Caplat C, Texier H, Barillier D, Lelievre C (2005) Heavy metals mobility in harbour contaminated sediments:
The case of Port-en-Bessin Marine Pollution Bulletin 50:504-511 doi:10.1016/j.marpolbul.2004.08.004
Cappuyns V, Swennen R (2008) The Use of Leaching Tests to Study the Potential Mobilization of Heavy Metals
from Soils and Sediments: A Comparison Water Air Soil Pollut 191:95-111 doi:10.1007/s11270-007-
9609-4
Casado-Martínez MC, Forja JM, DelValls TA (2009) A multivariate assessment of sediment contamination in
dredged materials from Spanish ports Journal of Hazardous Materials 163:1353-1359
doi:http://dx.doi.org/10.1016/j.jhazmat.2008.07.106
Chatain V et al. (2013a) Mineralogical study and leaching behavior of a stabilized harbor sediment with
hydraulic binder Environ Sci Pollut Res:1-9 doi:10.1007/s11356-012-1141-4
Chatain V, Blanc D, Borschneck D, Delolme C (2013b) Determining the experimental leachability of copper,
lead, and zinc in a harbor sediment and modeling Environ Sci Pollut Res:1-9 doi:10.1007/s11356-012-
1233-1
Demers I, Bussière B, Mbonimpa M, Benzaazoua M (2009) Oxygen diffusion and consumption in low-sulphide
tailings covers Canadian Geotechnical Journal 46:454-469 doi:doi:10.1139/T08-132
Dı́ez S, Ábalos M, Bayona JM (2002) Organotin contamination in sediments from the Western Mediterranean
enclosures following 10 years of TBT regulation Water Research 36:905-918 doi:10.1016/s0043-
1354(01)00305-0
Dold B, Fontboté L (2002) A mineralogical and geochemical study of element mobility in sulfide mine tailings
of Fe oxide Cu–Au deposits from the Punta del Cobre belt, northern Chile Chemical Geology 189:135-
163 doi:http://dx.doi.org/10.1016/S0009-2541(02)00044-X
Eek E, Cornelissen G, Kibsgaard A, Breedveld GD (2008) Diffusion of PAH and PCB from contaminated
sediments with and without mineral capping; measurement and modelling Chemosphere 71:1629-1638
doi:http://dx.doi.org/10.1016/j.chemosphere.2008.01.051
Elberling B, Balić-Žunić T, Edsberg A (2003) Spatial variations and controls of acid mine drainage generation
Environmental Geology 43:806-813 doi:10.1007/s00254-002-0695-8
Elberling B, Nicholson RV (1996) Field determination of sulphide oxidation rates in mine tailings Water Resour
Res 32:1773-1784 doi:10.1029/96wr00487
Elberling B, Nicholson RV, Reardon EJ, Tibble R (1994) Evaluation of sulphide oxidation rates: a laboratory
study comparing oxygen fluxes and rates of oxidation product release Canadian Geotechnical Journal
31:375-383 doi:doi:10.1139/t94-045
European Council (2002) Commission decision of 3 may 2000 replacing Decision 94/3/EC establishing a list of
wastes, consolidated version of 01 january 2002. (in
Förstner U, Calmano W, Conradt K, Jaksch H, Schimkus C, Schoer J (1981) Chemical speciation of heavy
metals in solid waste materials (sewage sludge, mining wastes, dredged materials, polluted sediments)
13
by sequential extraction. Universitätsbibliothek der Technischen Universität Hamburg-Harburg,
Hamburg-Harburg (in
French Official Journal (2007) JORF n°240 du 16 octobre 2007 p.17002 texte n°1. (in French)
Graupner T et al. (2007) Formation of sequences of cemented layers and hardpans within sulfide-bearing mine
tailings (mine district Freiberg, Germany) Applied Geochemistry 22:2486-2508
doi:http://dx.doi.org/10.1016/j.apgeochem.2007.07.002
Guevara-Riba A, Sahuquillo A, Rubio R, Rauret G (2004) Assessment of metal mobility in dredged harbour
sediments from Barcelona, Spain Science of The Total Environment 321:241-255
doi:http://dx.doi.org/10.1016/j.scitotenv.2003.08.021
Huerta-Diaz MA, Tessier A, Carignan R (1998) Geochemistry of trace metals associated with reduced sulfur in
freshwater sediments Applied Geochemistry 13:213-233 doi:10.1016/s0883-2927(97)00060-7
Isaure M-P et al. (2002) Quantitative Zn speciation in a contaminated dredged sediment by μ-PIXE, μ-SXRF,
EXAFS spectroscopy and principal component analysis Geochimica et Cosmochimica Acta 66:1549-
1567 doi:10.1016/s0016-7037(01)00875-4
Isaure M-P, Manceau A, Geoffroy N, Laboudigue A, Tamura N, Marcus MA (2005) Zinc mobility and
speciation in soil covered by contaminated dredged sediment using micrometer-scale and bulk-
averaging X-ray fluorescence, absorption and diffraction techniques Geochimica et Cosmochimica Acta
69:1173-1198 doi:10.1016/j.gca.2004.08.024
Jones B, Turki A (1997) Distribution and speciation of heavy metals in surficial sediments from the Tees
Estuary, north-east England Marine Pollution Bulletin 34:768-779 doi:10.1016/s0025-326x(97)00047-7
Le Guyader C (2011) Enquête "Dragage 2009" - Synthèse des données. CETMEF, Margny Lès Compiègne (in
French)
Le Guyader C (2013) Enquête "Dragage 2010" - Synthèse des données. CETMEF, Margny Lès Compiègne (in
French)
Lions J, Guérin V, Bataillard P, van der Lee J, Laboudigue A (2010) Metal availability in a highly contaminated,
dredged-sediment disposal site: Field measurements and geochemical modeling Environmental
Pollution 158:2857-2864 doi:10.1016/j.envpol.2010.06.011
Lions J, van der Lee J, Guérin V, Bataillard P, Laboudigue A (2007) Zinc and cadmium mobility in a 5-year-old
dredged sediment deposit: Experiments and modelling Journal of Soils and Sediments 7:207-215
doi:10.1065/jss2007.05.226
Lowers HA, Breit GN, Foster AL, Whitney J, Yount J, Uddin MN, Muneem AA (2007) Arsenic incorporation
into authigenic pyrite, Bengal Basin sediment, Bangladesh Geochimica et Cosmochimica Acta 71:2699-
2717 doi:http://dx.doi.org/10.1016/j.gca.2007.03.022
Lowson RT (1982) Aqueous oxidation of pyrite by molecular oxygen Chemical Reviews 82:461-497
doi:10.1021/cr00051a001
Mamindy-Pajany Y, Geret F, Roméo M, Hurel C, Marmier N (2012) Ex situ remediation of contaminated
sediments using mineral additives: Assessment of pollutant bioavailability with the Microtox solid
phase test Chemosphere 86:1112-1116 doi:http://dx.doi.org/10.1016/j.chemosphere.2011.12.001
Mbonimpa M, Akué Awoh S, Aubertin M (2012) A simple interpretation for the modified oxygen consumption
test on sulphide tailings. Paper presented at the GeoManitoba, Winnipeg, Canada,
Mbonimpa M, Aubertin M, Aachib M, Bussière B (2003) Diffusion and consumption of oxygen in unsaturated
cover materials Canadian Geotechnical Journal 40:916-932 doi:doi:10.1139/t03-040
Morse JW, Luther Iii GW (1999) Chemical influences on trace metal-sulfide interactions in anoxic sediments
Geochimica et Cosmochimica Acta 63:3373-3378 doi:10.1016/s0016-7037(99)00258-6
Mtambanengwe F, Mapfumo P, Kirchmann H (2004) Decomposition of organic matter in soil as influenced by
texture and pore size distribution Managing nutrient cycles to sustain soil fertility in sub-Saharan Africa
Ed, Bationo, A Centro Internacional de Agriculture Tropical pp:261-276
Ouangrawa M, Molson J, Aubertin M, Bussière B, Zagury GJ (2009) Reactive transport modelling of mine
tailings columns with capillarity-induced high water saturation for preventing sulfide oxidation Applied
Geochemistry 24:1312-1323 doi:http://dx.doi.org/10.1016/j.apgeochem.2009.04.005
Ouellet S, Bussière B, Mbonimpa M, Benzaazoua M, Aubertin M (2006) Reactivity and mineralogical evolution
of an underground mine sulphidic cemented paste backfill Minerals Engineering 19:407-419
doi:10.1016/j.mineng.2005.10.006
Pierret M-C, Blanc G, Clauer N (2000) Sur l'origine de la pyrite framboïdale dans les sédiments de la fosse
Suakin (mer Rouge) Comptes Rendus de l'Académie des Sciences - Series IIA - Earth and Planetary
Science 330:31-38 doi:10.1016/s1251-8050(00)00103-8
Pourbaix M, de Zoubov N, Van Muylder J (1963) Atlas d'équilibres électrochimiques vol 1. Gauthier-Villars
Paris,
14
Prokop Z, Vangheluwe ML, Van Sprang PA, Janssen CR, Holoubek I (2003) Mobility and toxicity of metals in
sandy sediments deposited on land Ecotoxicology and Environmental Safety 54:65-73
doi:10.1016/s0147-6513(02)00022-2
Puget P, Chenu C, Balesdent J (2000) Dynamics of soil organic matter associated with particle-size fractions of
water-stable aggregates European Journal of Soil Science 51:595-605 doi:10.1111/j.1365-
2389.2000.00353.x
Raudsepp M, Pani E (2003) Application of Rietveld analysis to environmental mineralogy Environmental
aspects of mine wastes Mineralogical Association of Canada Short Course 3:165-180
Ribecco C, Baker ME, Šášik R, Zuo Y, Hardiman G, Carnevali O (2011) Biological effects of marine
contaminated sediments on Sparus aurata juveniles Aquatic Toxicology 104:308-316
doi:http://dx.doi.org/10.1016/j.aquatox.2011.05.005
Salomons W, Rooij NM, Kerdijk H, Bril J (1987) Sediments as a source for contaminants? Hydrobiologia
149:13-30 doi:10.1007/bf00048643
Sauvé S, Hendershot W, Allen HE (2000) Solid-Solution Partitioning of Metals in Contaminated Soils:
Dependence on pH, Total Metal Burden, and Organic Matter Environmental Science & Technology
34:1125-1131 doi:10.1021/es9907764
Schenau SJ, Passier HF, Reichart GJ, de Lange GJ (2002) Sedimentary pyrite formation in the Arabian Sea
Marine Geology 185:393-402 doi:http://dx.doi.org/10.1016/S0025-3227(02)00183-4
Schippers A, Jørgensen BB (2002) Biogeochemistry of pyrite and iron sulfide oxidation in marine sediments
Geochimica et Cosmochimica Acta 66:85-92 doi:10.1016/s0016-7037(01)00745-1
Sobek AA, Schuller WA, Freeman JR, Smith RM (1978) Field and laboratory methods applicable to overburden
and minesoils vol Report EPA-600/2-78-054. US Environmental Protection Agency, (in
Staniszewska M, Burska D, Sapota G, Bogdaniuk M, Borowiec K, Nosarzewska I, Bolałek J (2011) The
relationship between the concentrations and distribution of organic pollutants and black carbon content
in benthic sediments in the Gulf of Gdańsk, Baltic Sea Marine Pollution Bulletin 62:1464-1475
doi:http://dx.doi.org/10.1016/j.marpolbul.2011.04.013
Sundaray SK, Nayak BB, Lin S, Bhatta D (2011) Geochemical speciation and risk assessment of heavy metals in
the river estuarine sediments—A case study: Mahanadi basin, India Journal of Hazardous Materials
186:1837-1846 doi:http://dx.doi.org/10.1016/j.jhazmat.2010.12.081
Tanji KK (1969) Solubility of gypsum in aqueous electrolytes as affected by ion association and ionic strengths
up to 0.15M and at 25.deg Environmental Science & Technology 3:656-661 doi:10.1021/es60030a003
Tessier E, Garnier C, Mullot J-U, Lenoble V, Arnaud M, Raynaud M, Mounier S (2011) Study of the spatial and
historical distribution of sediment inorganic contamination in the Toulon bay (France) Marine Pollution
Bulletin 62:2075-2086 doi:http://dx.doi.org/10.1016/j.marpolbul.2011.07.022
Trefry JH, Metz S (1984) Selective leaching of trace metals from sediments as a function of pH Analytical
Chemistry 56:745-749 doi:10.1021/ac00268a034
Visconti F, De Paz JM, Rubio JL (2010) Calcite and gypsum solubility products in water-saturated salt-affected
soil samples at 25°C and at least up to 14 dS m−1 European Journal of Soil Science 61:255-270
doi:10.1111/j.1365-2389.2009.01214.x
Warwick P, Hall A, Pashley V, Van der Lee J, Maes A (1998) Zinc and cadmium mobility in sand: effects of
pH, speciation, Cation Exchange Capacity (CEC), humic acid and metal ions Chemosphere 36:2283-
2290 doi:http://dx.doi.org/10.1016/S0045-6535(97)10197-7
Ye S, Laws EA, Zhong S, Ding X, Pang S (2011) Sequestration of metals through association with pyrite in
subtidal sediments of the Nanpaishui Estuary on the Western Bank of the Bohai Sea, China Marine
Pollution Bulletin 62:934-941 doi:http://dx.doi.org/10.1016/j.marpolbul.2011.02.052
Young RA (1993) The Rietveld method. Oxford University Press, NYC, NY, USA
15
Fig. 1 Schematic illustration of the experimental set-up for leaching and OC tests
16
Fig. 2 Dependence of OC to saturation degree with calculated oxygen flux from OC-Test in
mol(O2).m-².s-1
0
20
40
60
80
100
120
140
60% 70% 80% 90% 100%
O2
flu
x (m
ol(
O2).
m-2
.s-1
)
Saturation degree
17
Fig. 3 SEM-EDS back-scattered electron images of sediment showing framboïdal pyrite (Pf,
a) surrounded by a complex aggregate containing quartz (Q, red color) and calcite (C, green
color), and massive pyrite (P, b) with an Fe-oxi-hydroxides replacement (O)
18
Fig. 4 Evolution of leachates volume, conductivity (a), pH, and ORP (b) during the column
leaching test; vertical dashed line in (b) indicates a change in geochemical behavior after 12th
week
19
Fig. 5 Sulfates concentrations (mg/kg of dry matter (DM)), cumulative percentages of
sulfates fraction of sulfur (in % from total sulfur) (a), Ca, and Mg concentrations (in mg/kg
DM, b) in leaching solutions during the column leaching test; vertical dashed line indicates a
change in geochemical behavior after 12th week
20
Fig. 6 Cu, Fe and Zn concentrations into leachates during the column leaching test; vertical
dashed line indicates a change in geochemical behavior after 12th week
0.00
0.10
0.20
0.30
0.40
0.50
0 10 20 30
Cu
, Fe
an
d Z
n r
ele
ase
d (
mg/
kg D
M)
Time (weeks)
Cu
Fe
Zn
21
Fig. 7 Oxygen consumption into OC-Test with oxygen flux and corresponding saturation
degree Sr; vertical dashed line indicates a change in geochemical behavior after 12th week
0%
10%
20%
30%
40%
50%
60%
70%
80%
90%
100%
0
20
40
60
80
100
120
140
160
180
0 10 20 30
Satu
rati
on
de
gre
e S
r
O2
flu
x (m
ol(
O2).
m-2
.s-1
)
Time (weeks)
O2 flux
Sr
22
Fig. 8 Reactional schema of involved components into marine sediments and methodological
protocol analysis
23
Fig. 9 Cumulated Ca and Ca + Mg released molar concentrations versus cumulated sulfates
released molar concentrations (a), evolution of Ca versus sulfates molar ratio, and Ca versus
Mg molar ratio versus time (b) into leachates
24
Fig. 10 Correlation between cumulated Cu and Zn molar concentrations and cumulated
sulfates molar concentrations (a), and cumulated DOC (b) in the leachates
0.E+00
1.E-05
2.E-05
3.E-05
4.E-05
5.E-05
6.E-05
7.E-05
0.0E+00 5.0E-02 1.0E-01 1.5E-01
Cu
mu
late
d m
eta
ls r
ele
ase
d (
mo
l/kg
DM
)
Cumulated sulfates released (mol/kg DM)
Cu
Zn
a.
0.E+00
1.E-05
2.E-05
3.E-05
4.E-05
5.E-05
6.E-05
7.E-05
0.E+00 5.E-03 1.E-02 2.E-02 2.E-02
Cu
mu
late
d m
eta
ls r
ele
ase
d (
mo
l/kg
DM
)
Cumulated DOC released (mol/kg DM)
Cu
Zn
b.
25
Table 1 Physicochemical characteristics of the sediment
Gs (g/cm3)
Water content (wt.%)
Total carbon (wt.%)
TOC (wt.%)
Total sulfur (wt.%)
HCl-extractable
sulfur (wt.%)
Other sulfur forms (wt.%)
Bulk Sediment
2.55 23.3 9.89 6.27 2.02 1.04 0.98
26
Table 2 Chemical composition of the sediment (ICP-AES) and comparison to the regulatory
threshold levels N1 and N2 for trace metals (French regulation)
Ca (wt.%) Mg
(wt.%)
Na
(wt.%) Fe (wt.%)
Cu
(mg/kg)
Pb
(mg/kg)
Zn
(mg/kg)
Bulk
Sediment 19.7 2.07 0.3 3.38 930 1020 2250
N1 level - - - - 45 100 276
N2 level - - - - 90 200 552
27
Table 3 XRD mineralogical analysis of the sediment with concentrations calculated
accordingly to Rietveld method (Young 1993)
Name Formulas Concentration
(wt.%) Quartz SiO2 15.3
Muscovite KAl2(Si3Al)O10(OH,F)2 9.2
Chamosite (Fe,Mg)5Al(Si3Al)O10(OH,O) 4.5
Illite (K,H3O)(Al,Mg,Fe)2(Si,Al)4O10[(OH)2,(H2O)] 1.6
Kaolinite Al2Si2O5(OH)4 4.0
Dolomite CaMg(CO3)2 13.6
Calcite CaCO3 38.9
Halite NaCl 0.8
Pyrite FeS2 2.0
Magnétite Fe3O4 1.1
Gypse CaSO4;2H2O 5.0