Upload
others
View
5
Download
0
Embed Size (px)
Citation preview
1079Singapore: +65 6779 [email protected]
USA: +1 330 486 [email protected]
Germany: +49 621 [email protected]
Pepperl+Fuchs Groupwww.pepperl-fuchs.com
Subject to modifications without notice Copyright Pepperl+Fuchs
Special Functions D
evicesAmplifiers, Counters, Timers & Controls
Digital Display Meter ............................................................... 1080Counter/Timer/Tachometer .................................................... 1084Terminal Amplifier/Converter ................................................. 1092Sensor Output Converter ....................................................... 1096Speed Monitor ......................................................................... 1098Frequency to Voltage/Curent ................................................. 1100Zero Speed Monitor................................................................. 1102
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
1080 Singapore: +65 6779 [email protected]
USA: +1 330 486 [email protected]
Germany: +49 621 [email protected]
Pepperl+Fuchs Groupwww.pepperl-fuchs.com
Subject to modifications without notice Copyright Pepperl+Fuchs
Special Functions Devices
Spec
ial F
unct
ions
Dev
ices
• Bright, high contrast 5-digit LED indica-tor
• Leading zero suppression• Adjustable decimal point• Maximum- and minimium-value display
FunctionThe DA5-IU-C permits a simple visualinspection by operating and maintenancepersonnel. It converts the analogue sensoroutput signal into a readable form for thispurpose. Depending on the task or setting,4 ... 20 mA or 0 ... 100 % values can be dis-played.
Scope of delivery:• Process control unit DA5-IU-C• Screw terminal, 7-pin• Clamp clip• Seal• 1 sheet of adhesive symbols
Dimensions
Electrical connection
DA5-IU-CGeneral specificationsPre-selection noneData storage 106 storage cycles or 10 years, EEPROMProgramming keypad-driven menuIndicators/operating meansType 7-segment LED display, redNumber of decades 5Display value digit height 8 mmDisplay interval -19999 ... 99999Decimal point freely adjustableResolution 14 BitScale factor via linear characteristic curveReset maximum value, manuallyKey interlock -Electrical specificationsOperating voltage 10 ... 30 V DCPower consumption 1.5 VAInputImpedance 1 MOhmVoltage max. 30 DCAnalogue voltage input 0 ... 10 V / 2 ... 10 V DCAnalogue current input 0 ... 20 mA / 4 ... 20 mAMechanical specificationsConnection 7-pin screw terminal
max. core cross-section 0.34 ... 1.5 mm2
Mass approx. 50 g
1 2 3 4 5 6 7
max. 19.3
59 6.5
4
22 x
45
48
24
TerminalNo.1234567
10 ... 30 V DC0 V (GND)0 V LATCHLATCHCurrent input0 V input signalVoltage input
1 2 3 4 5 6 7
• Bright, high contrast 5-digit LED indica-tor
• Leading zero suppression• Adjustable decimal point• Maximum- and minimium-value display
FunctionThe DA5-IU-C permits a simple visualinspection by operating and maintenancepersonnel. It converts the analogue sensoroutput signal into a readable form for thispurpose. Depending on the task or setting,4 ... 20 mA or 0 ... 100 % values can be dis-played.
Scope of delivery:• Process control unit DA5-IU-C• Screw terminal, 7-pin• Clamp clip• Seal• 1 sheet of adhesive symbols
Dimensions
Electrical connection
DA5-IU-CGeneral specificationsPre-selection noneData storage 106 storage cycles or 10 years, EEPROMProgramming keypad-driven menuIndicators/operating meansType 7-segment LED display, redNumber of decades 5Display value digit height 8 mmDisplay interval -19999 ... 99999Decimal point freely adjustableResolution 14 BitScale factor via linear characteristic curveReset maximum value, manuallyKey interlock -Electrical specificationsOperating voltage 10 ... 30 V DCPower consumption 1.5 VAInputImpedance 1 MOhmVoltage max. 30 DCAnalogue voltage input 0 ... 10 V / 2 ... 10 V DCAnalogue current input 0 ... 20 mA / 4 ... 20 mAMechanical specificationsConnection 7-pin screw terminal
max. core cross-section 0.34 ... 1.5 mm2
Mass approx. 50 g
1 2 3 4 5 6 7
max. 19.3
59 6.5
4
22 x
45
48
24
TerminalNo.1234567
10 ... 30 V DC0 V (GND)0 V LATCHLATCHCurrent input0 V input signalVoltage input
1 2 3 4 5 6 7
Digital Display Meter
Technical Specifications
• Analog voltage or current• Bright, high contrast 5-digit LED indicator• Leading zero suppression• Adjustable decimal point• Maximum- and minimium-value display
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
1081Singapore: +65 6779 [email protected]
USA: +1 330 486 [email protected]
Germany: +49 621 [email protected]
Pepperl+Fuchs Groupwww.pepperl-fuchs.com
Subject to modifications without notice Copyright Pepperl+Fuchs
Special Functions Devices
Special Functions Devices
• Bright, high contrast 5-digit LED indica-tor
• Leading zero suppression• Adjustable decimal point• Maximum- and minimium-value display
FunctionThe DA5-IU-C permits a simple visualinspection by operating and maintenancepersonnel. It converts the analogue sensoroutput signal into a readable form for thispurpose. Depending on the task or setting,4 ... 20 mA or 0 ... 100 % values can be dis-played.
Scope of delivery:• Process control unit DA5-IU-C• Screw terminal, 7-pin• Clamp clip• Seal• 1 sheet of adhesive symbols
Dimensions
Electrical connection
DA5-IU-CGeneral specificationsPre-selection noneData storage 106 storage cycles or 10 years, EEPROMProgramming keypad-driven menuIndicators/operating meansType 7-segment LED display, redNumber of decades 5Display value digit height 8 mmDisplay interval -19999 ... 99999Decimal point freely adjustableResolution 14 BitScale factor via linear characteristic curveReset maximum value, manuallyKey interlock -Electrical specificationsOperating voltage 10 ... 30 V DCPower consumption 1.5 VAInputImpedance 1 MOhmVoltage max. 30 DCAnalogue voltage input 0 ... 10 V / 2 ... 10 V DCAnalogue current input 0 ... 20 mA / 4 ... 20 mAMechanical specificationsConnection 7-pin screw terminal
max. core cross-section 0.34 ... 1.5 mm2
Mass approx. 50 g
1 2 3 4 5 6 7
max. 19.3
59 6.5
4
22 x
45
48
24
TerminalNo.1234567
10 ... 30 V DC0 V (GND)0 V LATCHLATCHCurrent input0 V input signalVoltage input
1 2 3 4 5 6 7
• Bright, high contrast 5-digit LED indica-tor
• Leading zero suppression• Adjustable decimal point• Maximum- and minimium-value display
FunctionThe DA5-IU-C permits a simple visualinspection by operating and maintenancepersonnel. It converts the analogue sensoroutput signal into a readable form for thispurpose. Depending on the task or setting,4 ... 20 mA or 0 ... 100 % values can be dis-played.
Scope of delivery:• Process control unit DA5-IU-C• Screw terminal, 7-pin• Clamp clip• Seal• 1 sheet of adhesive symbols
Dimensions
Electrical connection
DA5-IU-CGeneral specificationsPre-selection noneData storage 106 storage cycles or 10 years, EEPROMProgramming keypad-driven menuIndicators/operating meansType 7-segment LED display, redNumber of decades 5Display value digit height 8 mmDisplay interval -19999 ... 99999Decimal point freely adjustableResolution 14 BitScale factor via linear characteristic curveReset maximum value, manuallyKey interlock -Electrical specificationsOperating voltage 10 ... 30 V DCPower consumption 1.5 VAInputImpedance 1 MOhmVoltage max. 30 DCAnalogue voltage input 0 ... 10 V / 2 ... 10 V DCAnalogue current input 0 ... 20 mA / 4 ... 20 mAMechanical specificationsConnection 7-pin screw terminal
max. core cross-section 0.34 ... 1.5 mm2
Mass approx. 50 g
1 2 3 4 5 6 7
max. 19.3
59 6.5
4
22 x
45
48
24
TerminalNo.1234567
10 ... 30 V DC0 V (GND)0 V LATCHLATCHCurrent input0 V input signalVoltage input
1 2 3 4 5 6 7
Wiring Diagrams
Dimensions
Terminal Connection
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
1082 Singapore: +65 6779 [email protected]
USA: +1 330 486 [email protected]
Germany: +49 621 [email protected]
Pepperl+Fuchs Groupwww.pepperl-fuchs.com
Subject to modifications without notice Copyright Pepperl+Fuchs
Special Functions Devices
Spec
ial F
unct
ions
Dev
ices
• 2 adjustable limit values• 2 relay outputs• Operation via keypad• Programmable characteristics• Resetting the outputs, automatic, ma-
nual or with external signal• Connection via plug-in screw terminals• Auxiliary power output for sensors (On-
ly DA5-IU-2K-V)• Protection degree IP65 in accordance
with DIN EN 60529 (front only)• Shock resistance in accordance with
DIN EN 60068-2-27• Vibration resistance in accordance with
DIN EN 60068-2-6• System hum suppression
FunctionThe DA5-IU-2K-... permits a simple visualinspection by operating and maintenancepersonnel. It converts the analogue sensoroutput signal into a readable form for thispurpose. Depending on the task or setting,4 mA ... 20 mA or 0 % ... 100 % values canbe displayed.
Scope of delivery:• Process control unit DA5-IU-2K-...• Screw terminals
1 RM 5.08 8-pole terminal for power sup-ply and outputs1 RM 3.81 11-pole terminal for measuringand control inputs
• Clamp clip• Seal• 1 sheet of adhesive symbols
Dimensions
Electrical connection
DA5-IU-2K-C DA5-IU-2K-VGeneral specificationsPre-selection 2-foldData storage 106 storage cycles or 10 years, EEPROMProgramming keypad-driven menuIndicators/operating meansType 7-segment LED display, redNumber of decades 5Display value digit height 14.2 mmPre-selection digit height 14.2 mmDisplay interval -19999 ... 99999Decimal point freely adjustableResolution 14 BitScale factor via characteristic curve with up to 24 value pairsReset manually or externalKey interlock with "high"-level at terminal "KEY"Electrical specificationsOperating voltage 10 ... 30 V DC 90 ... 260 V ACPower consumption 2 W 7 VAOutputRelay 2 x 250 V AC/ 300 V DC, 3 A, changeo-
ver contact2 x 250 V AC/ 300 V DC, 3 A, changeo-
ver contactSensor supply - 24 V DC , 100 mAInputImpedance > 1 MΩ for voltage measurement
< 50 Ω for current measurementAnalogue voltage input 0 ... 10 V / 2 ... 10 V DC,
-10 ... 10 V DCAnalogue current input 0 ... 20 mA / 4 ... 20 mAMechanical specificationsConnection 8-pin and 11 pin connectors with plug-in screw terminalsMass 220 g
Control panel cutout
96
48
44.9
x91.
9
92+0.8
67.1 6.5
4
max. 19
45+
0.6
15.5
not assigned
on S1
Reset S1/8
Auxiliary power output(only on DA5-IU-2K-V)
Reference earth for reset S1/7
Key lock-out "Key" S1/6
Voltmeter input S1/3
Reference earth S1/2
Ammeter input S1/1
90 ... 260 V AC supply (...-V)10 ... 30 V DC 0 V DC (...-C) Connector S1/... Connector S2/...
Indicator
Relay 2
Relay 1
+24
V D
C,
0 V
DC
OUT 1 S2/3
4 5 10 S1/11
100
mA
S1/9
S2/2
S2/1OUT 2 S2/6
S2/5
S2/4
S2/7 S2/8
• 2 adjustable limit values• 2 relay outputs• Operation via keypad• Programmable characteristics• Resetting the outputs, automatic, ma-
nual or with external signal• Connection via plug-in screw terminals• Auxiliary power output for sensors (On-
ly DA5-IU-2K-V)• Protection degree IP65 in accordance
with DIN EN 60529 (front only)• Shock resistance in accordance with
DIN EN 60068-2-27• Vibration resistance in accordance with
DIN EN 60068-2-6• System hum suppression
FunctionThe DA5-IU-2K-... permits a simple visualinspection by operating and maintenancepersonnel. It converts the analogue sensoroutput signal into a readable form for thispurpose. Depending on the task or setting,4 mA ... 20 mA or 0 % ... 100 % values canbe displayed.
Scope of delivery:• Process control unit DA5-IU-2K-...• Screw terminals
1 RM 5.08 8-pole terminal for power sup-ply and outputs1 RM 3.81 11-pole terminal for measuringand control inputs
• Clamp clip• Seal• 1 sheet of adhesive symbols
Dimensions
Electrical connection
DA5-IU-2K-C DA5-IU-2K-VGeneral specificationsPre-selection 2-foldData storage 106 storage cycles or 10 years, EEPROMProgramming keypad-driven menuIndicators/operating meansType 7-segment LED display, redNumber of decades 5Display value digit height 14.2 mmPre-selection digit height 14.2 mmDisplay interval -19999 ... 99999Decimal point freely adjustableResolution 14 BitScale factor via characteristic curve with up to 24 value pairsReset manually or externalKey interlock with "high"-level at terminal "KEY"Electrical specificationsOperating voltage 10 ... 30 V DC 90 ... 260 V ACPower consumption 2 W 7 VAOutputRelay 2 x 250 V AC/ 300 V DC, 3 A, changeo-
ver contact2 x 250 V AC/ 300 V DC, 3 A, changeo-
ver contactSensor supply - 24 V DC , 100 mAInputImpedance > 1 MΩ for voltage measurement
< 50 Ω for current measurementAnalogue voltage input 0 ... 10 V / 2 ... 10 V DC,
-10 ... 10 V DCAnalogue current input 0 ... 20 mA / 4 ... 20 mAMechanical specificationsConnection 8-pin and 11 pin connectors with plug-in screw terminalsMass 220 g
Control panel cutout
96
48
44.9
x91.
9
92+0.8
67.1 6.5
4
max. 19
45+
0.6
15.5
not assigned
on S1
Reset S1/8
Auxiliary power output(only on DA5-IU-2K-V)
Reference earth for reset S1/7
Key lock-out "Key" S1/6
Voltmeter input S1/3
Reference earth S1/2
Ammeter input S1/1
90 ... 260 V AC supply (...-V)10 ... 30 V DC 0 V DC (...-C) Connector S1/... Connector S2/...
Indicator
Relay 2
Relay 1
+24
V D
C,
0 V
DC
OUT 1 S2/3
4 5 10 S1/11
100
mA
S1/9
S2/2
S2/1OUT 2 S2/6
S2/5
S2/4
S2/7 S2/8
Digital Display Meter
Technical Specifications
• 2 adjustable limit values• 2 relay outputs• Programmable characteristics• Resetting the outputs, automatic,
manual or with external signal• Auxiliary power output for sensors
(DA5-IU-2K-V)
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
1083Singapore: +65 6779 [email protected]
USA: +1 330 486 [email protected]
Germany: +49 621 [email protected]
Pepperl+Fuchs Groupwww.pepperl-fuchs.com
Subject to modifications without notice Copyright Pepperl+Fuchs
Special Functions Devices
Special Functions Devices
• 2 adjustable limit values• 2 relay outputs• Operation via keypad• Programmable characteristics• Resetting the outputs, automatic, ma-
nual or with external signal• Connection via plug-in screw terminals• Auxiliary power output for sensors (On-
ly DA5-IU-2K-V)• Protection degree IP65 in accordance
with DIN EN 60529 (front only)• Shock resistance in accordance with
DIN EN 60068-2-27• Vibration resistance in accordance with
DIN EN 60068-2-6• System hum suppression
FunctionThe DA5-IU-2K-... permits a simple visualinspection by operating and maintenancepersonnel. It converts the analogue sensoroutput signal into a readable form for thispurpose. Depending on the task or setting,4 mA ... 20 mA or 0 % ... 100 % values canbe displayed.
Scope of delivery:• Process control unit DA5-IU-2K-...• Screw terminals
1 RM 5.08 8-pole terminal for power sup-ply and outputs1 RM 3.81 11-pole terminal for measuringand control inputs
• Clamp clip• Seal• 1 sheet of adhesive symbols
Dimensions
Electrical connection
DA5-IU-2K-C DA5-IU-2K-VGeneral specificationsPre-selection 2-foldData storage 106 storage cycles or 10 years, EEPROMProgramming keypad-driven menuIndicators/operating meansType 7-segment LED display, redNumber of decades 5Display value digit height 14.2 mmPre-selection digit height 14.2 mmDisplay interval -19999 ... 99999Decimal point freely adjustableResolution 14 BitScale factor via characteristic curve with up to 24 value pairsReset manually or externalKey interlock with "high"-level at terminal "KEY"Electrical specificationsOperating voltage 10 ... 30 V DC 90 ... 260 V ACPower consumption 2 W 7 VAOutputRelay 2 x 250 V AC/ 300 V DC, 3 A, changeo-
ver contact2 x 250 V AC/ 300 V DC, 3 A, changeo-
ver contactSensor supply - 24 V DC , 100 mAInputImpedance > 1 MΩ for voltage measurement
< 50 Ω for current measurementAnalogue voltage input 0 ... 10 V / 2 ... 10 V DC,
-10 ... 10 V DCAnalogue current input 0 ... 20 mA / 4 ... 20 mAMechanical specificationsConnection 8-pin and 11 pin connectors with plug-in screw terminalsMass 220 g
Control panel cutout
96
48
44.9
x91.
9
92+0.8
67.1 6.5
4
max. 19
45+
0.6
15.5
not assigned
on S1
Reset S1/8
Auxiliary power output(only on DA5-IU-2K-V)
Reference earth for reset S1/7
Key lock-out "Key" S1/6
Voltmeter input S1/3
Reference earth S1/2
Ammeter input S1/1
90 ... 260 V AC supply (...-V)10 ... 30 V DC 0 V DC (...-C) Connector S1/... Connector S2/...
Indicator
Relay 2
Relay 1
+24
V D
C,
0 V
DC
OUT 1 S2/3
4 5 10 S1/11
100
mA
S1/9
S2/2
S2/1OUT 2 S2/6
S2/5
S2/4
S2/7 S2/8
• 2 adjustable limit values• 2 relay outputs• Operation via keypad• Programmable characteristics• Resetting the outputs, automatic, ma-
nual or with external signal• Connection via plug-in screw terminals• Auxiliary power output for sensors (On-
ly DA5-IU-2K-V)• Protection degree IP65 in accordance
with DIN EN 60529 (front only)• Shock resistance in accordance with
DIN EN 60068-2-27• Vibration resistance in accordance with
DIN EN 60068-2-6• System hum suppression
FunctionThe DA5-IU-2K-... permits a simple visualinspection by operating and maintenancepersonnel. It converts the analogue sensoroutput signal into a readable form for thispurpose. Depending on the task or setting,4 mA ... 20 mA or 0 % ... 100 % values canbe displayed.
Scope of delivery:• Process control unit DA5-IU-2K-...• Screw terminals
1 RM 5.08 8-pole terminal for power sup-ply and outputs1 RM 3.81 11-pole terminal for measuringand control inputs
• Clamp clip• Seal• 1 sheet of adhesive symbols
Dimensions
Electrical connection
DA5-IU-2K-C DA5-IU-2K-VGeneral specificationsPre-selection 2-foldData storage 106 storage cycles or 10 years, EEPROMProgramming keypad-driven menuIndicators/operating meansType 7-segment LED display, redNumber of decades 5Display value digit height 14.2 mmPre-selection digit height 14.2 mmDisplay interval -19999 ... 99999Decimal point freely adjustableResolution 14 BitScale factor via characteristic curve with up to 24 value pairsReset manually or externalKey interlock with "high"-level at terminal "KEY"Electrical specificationsOperating voltage 10 ... 30 V DC 90 ... 260 V ACPower consumption 2 W 7 VAOutputRelay 2 x 250 V AC/ 300 V DC, 3 A, changeo-
ver contact2 x 250 V AC/ 300 V DC, 3 A, changeo-
ver contactSensor supply - 24 V DC , 100 mAInputImpedance > 1 MΩ for voltage measurement
< 50 Ω for current measurementAnalogue voltage input 0 ... 10 V / 2 ... 10 V DC,
-10 ... 10 V DCAnalogue current input 0 ... 20 mA / 4 ... 20 mAMechanical specificationsConnection 8-pin and 11 pin connectors with plug-in screw terminalsMass 220 g
Control panel cutout
96
48
44.9
x91.
9
92+0.8
67.1 6.5
4
max. 19
45+
0.6
15.5
not assigned
on S1
Reset S1/8
Auxiliary power output(only on DA5-IU-2K-V)
Reference earth for reset S1/7
Key lock-out "Key" S1/6
Voltmeter input S1/3
Reference earth S1/2
Ammeter input S1/1
90 ... 260 V AC supply (...-V)10 ... 30 V DC 0 V DC (...-C) Connector S1/... Connector S2/...
Indicator
Relay 2
Relay 1
+24
V D
C,
0 V
DC
OUT 1 S2/3
4 5 10 S1/11
100
mA
S1/9
S2/2
S2/1OUT 2 S2/6
S2/5
S2/4
S2/7 S2/8
Wiring Diagrams
Dimensions
Terminal Connection
DA5-14-2K-C90 ...260 VAC
S2/7 VAC (N2)S2/8 VAC (L2)
DA5-14-2K-C10 ...30 VDC
S2/7 +VDCS2/8 GND
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
1084 Singapore: +65 6779 [email protected]
USA: +1 330 486 [email protected]
Germany: +49 621 [email protected]
Pepperl+Fuchs Groupwww.pepperl-fuchs.com
Subject to modifications without notice Copyright Pepperl+Fuchs
Special Functions Devices
Spec
ial F
unct
ions
Dev
ices
• Counter/Timer/Tachometer• Counter frequency up to 20 kHz• LED indicator, red• 6 decade devices• Operation via keypad• Two counter inputs• Fixing with plug-in frame for easy instal-
lation• Connection via screw terminals• Manual or external reset• PNP and NPN sensors can be connec-
ted• Protection degree IP65 in accordance
with DIN EN 60529 (front only)• Shock resistance in accordance with
DIN EN 60068-2-27• Vibration resistance in accordance with
DIN EN 60068-2-6
Dimensions
Electrical connection
KCT-6S-C KCT-6ST-CGeneral specificationsPre-selection - singleProgramming keypad-driven menu keypad-driven menuIndicators/operating meansType 7-segment LED display, red 7-segment LED display, redNumber of decades 6 6Display value digit height 8 mm digit height 8 mmPre-selection - active at counter value ≤ 0Display interval -199999 ... 999999 with suppression of
leading zeros-199999 ... 999999 with suppression of
leading zerosDecimal point 0 to max 3 fractional digits 0 to max 3 fractional digitsScale factor 0.0001 ... 99.9999 0.0001 ... 99.9999Reset manually or external manually or externalKey interlock - -Electrical specificationsOperating voltage 10 ... 30 V DCPower consumption 1.5 WInputCounting frequency 30 Hz / 20 kHzImpedance 10 kOhmVoltage low: 0 V DC ... 0.2 x supply voltage; high: 0.6 x supply voltage ... 30 V DCCounting method adding or subtractingOutputOptocoupler - Semiconductor output 30 V, max. 10 mAMechanical specificationsConnection 5-pin screw terminal ,
max. core cross-section 0.34 ... 1.5 mm27-pin screw terminal ,
max. core cross-section 0.34 ... 1.5 mm2
Mass 48 g 48 g
1 2 3 4 5 6 71 2 3 4 5
KCT-6S-C KCT-6ST-C
max. 19.3
59 6.5
4
22 x
45
48
24
4
5
3
2
6
7
1
Input B
Reset
Input A
10 ... 30 V DC
GND
Counting devicewith display
Polarity control
Optocoupler output(only KCT-6ST-C)
Counter / Timer / Tachometer
Technical Specifications
• Counter frequency up to 20 kHz• LED indicator, red• 6 decade devices• Operation via keypad• Two counter inputs• Manual or external reset• PNP and NPN sensors can
be connected
• Counter/Timer/Tachometer• Counter frequency up to 20 kHz• LED indicator, red• 6 decade devices• Operation via keypad• Two counter inputs• Fixing with plug-in frame for easy instal-
lation• Connection via screw terminals• Manual or external reset• PNP and NPN sensors can be connec-
ted• Protection degree IP65 in accordance
with DIN EN 60529 (front only)• Shock resistance in accordance with
DIN EN 60068-2-27• Vibration resistance in accordance with
DIN EN 60068-2-6
Dimensions
Electrical connection
KCT-6S-C KCT-6ST-CGeneral specificationsPre-selection - singleProgramming keypad-driven menu keypad-driven menuIndicators/operating meansType 7-segment LED display, red 7-segment LED display, redNumber of decades 6 6Display value digit height 8 mm digit height 8 mmPre-selection - active at counter value ≤ 0Display interval -199999 ... 999999 with suppression of
leading zeros-199999 ... 999999 with suppression of
leading zerosDecimal point 0 to max 3 fractional digits 0 to max 3 fractional digitsScale factor 0.0001 ... 99.9999 0.0001 ... 99.9999Reset manually or external manually or externalKey interlock - -Electrical specificationsOperating voltage 10 ... 30 V DCPower consumption 1.5 WInputCounting frequency 30 Hz / 20 kHzImpedance 10 kOhmVoltage low: 0 V DC ... 0.2 x supply voltage; high: 0.6 x supply voltage ... 30 V DCCounting method adding or subtractingOutputOptocoupler - Semiconductor output 30 V, max. 10 mAMechanical specificationsConnection 5-pin screw terminal ,
max. core cross-section 0.34 ... 1.5 mm27-pin screw terminal ,
max. core cross-section 0.34 ... 1.5 mm2
Mass 48 g 48 g
1 2 3 4 5 6 71 2 3 4 5
KCT-6S-C KCT-6ST-C
max. 19.3
59 6.5
4
22 x
45
48
24
4
5
3
2
6
7
1
Input B
Reset
Input A
10 ... 30 V DC
GND
Counting devicewith display
Polarity control
Optocoupler output(only KCT-6ST-C)
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
1085Singapore: +65 6779 [email protected]
USA: +1 330 486 [email protected]
Germany: +49 621 [email protected]
Pepperl+Fuchs Groupwww.pepperl-fuchs.com
Subject to modifications without notice Copyright Pepperl+Fuchs
Special Functions Devices
Special Functions Devices
Wiring Diagrams
Dimensions
• Counter/Timer/Tachometer• Counter frequency up to 20 kHz• LED indicator, red• 6 decade devices• Operation via keypad• Two counter inputs• Fixing with plug-in frame for easy instal-
lation• Connection via screw terminals• Manual or external reset• PNP and NPN sensors can be connec-
ted• Protection degree IP65 in accordance
with DIN EN 60529 (front only)• Shock resistance in accordance with
DIN EN 60068-2-27• Vibration resistance in accordance with
DIN EN 60068-2-6
Dimensions
Electrical connection
KCT-6S-C KCT-6ST-CGeneral specificationsPre-selection - singleProgramming keypad-driven menu keypad-driven menuIndicators/operating meansType 7-segment LED display, red 7-segment LED display, redNumber of decades 6 6Display value digit height 8 mm digit height 8 mmPre-selection - active at counter value ≤ 0Display interval -199999 ... 999999 with suppression of
leading zeros-199999 ... 999999 with suppression of
leading zerosDecimal point 0 to max 3 fractional digits 0 to max 3 fractional digitsScale factor 0.0001 ... 99.9999 0.0001 ... 99.9999Reset manually or external manually or externalKey interlock - -Electrical specificationsOperating voltage 10 ... 30 V DCPower consumption 1.5 WInputCounting frequency 30 Hz / 20 kHzImpedance 10 kOhmVoltage low: 0 V DC ... 0.2 x supply voltage; high: 0.6 x supply voltage ... 30 V DCCounting method adding or subtractingOutputOptocoupler - Semiconductor output 30 V, max. 10 mAMechanical specificationsConnection 5-pin screw terminal ,
max. core cross-section 0.34 ... 1.5 mm27-pin screw terminal ,
max. core cross-section 0.34 ... 1.5 mm2
Mass 48 g 48 g
1 2 3 4 5 6 71 2 3 4 5
KCT-6S-C KCT-6ST-C
max. 19.3
59 6.5
4
22 x
45
48
24
4
5
3
2
6
7
1
Input B
Reset
Input A
10 ... 30 V DC
GND
Counting devicewith display
Polarity control
Optocoupler output(only KCT-6ST-C)
• Counter/Timer/Tachometer• Counter frequency up to 20 kHz• LED indicator, red• 6 decade devices• Operation via keypad• Two counter inputs• Fixing with plug-in frame for easy instal-
lation• Connection via screw terminals• Manual or external reset• PNP and NPN sensors can be connec-
ted• Protection degree IP65 in accordance
with DIN EN 60529 (front only)• Shock resistance in accordance with
DIN EN 60068-2-27• Vibration resistance in accordance with
DIN EN 60068-2-6
Dimensions
Electrical connection
KCT-6S-C KCT-6ST-CGeneral specificationsPre-selection - singleProgramming keypad-driven menu keypad-driven menuIndicators/operating meansType 7-segment LED display, red 7-segment LED display, redNumber of decades 6 6Display value digit height 8 mm digit height 8 mmPre-selection - active at counter value ≤ 0Display interval -199999 ... 999999 with suppression of
leading zeros-199999 ... 999999 with suppression of
leading zerosDecimal point 0 to max 3 fractional digits 0 to max 3 fractional digitsScale factor 0.0001 ... 99.9999 0.0001 ... 99.9999Reset manually or external manually or externalKey interlock - -Electrical specificationsOperating voltage 10 ... 30 V DCPower consumption 1.5 WInputCounting frequency 30 Hz / 20 kHzImpedance 10 kOhmVoltage low: 0 V DC ... 0.2 x supply voltage; high: 0.6 x supply voltage ... 30 V DCCounting method adding or subtractingOutputOptocoupler - Semiconductor output 30 V, max. 10 mAMechanical specificationsConnection 5-pin screw terminal ,
max. core cross-section 0.34 ... 1.5 mm27-pin screw terminal ,
max. core cross-section 0.34 ... 1.5 mm2
Mass 48 g 48 g
1 2 3 4 5 6 71 2 3 4 5
KCT-6S-C KCT-6ST-C
max. 19.3
59 6.5
4
22 x
45
48
24
4
5
3
2
6
7
1
Input B
Reset
Input A
10 ... 30 V DC
GND
Counting devicewith display
Polarity control
Optocoupler output(only KCT-6ST-C)
Terminal Connection
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
1086 Singapore: +65 6779 [email protected]
USA: +1 330 486 [email protected]
Germany: +49 621 [email protected]
Pepperl+Fuchs Groupwww.pepperl-fuchs.com
Subject to modifications without notice Copyright Pepperl+Fuchs
Special Functions Devices
Spec
ial F
unct
ions
Dev
ices
• Counter/Timer/Tachometer• Counter frequency up to 20 kHz• 6-digit LED indicator, red• 1 Pre-selection• Status LED indication for output an pre-
selection value• Display range and preselection range
from -199999 up to 999999Overflow will be evaluated correctly up to 1 decade
• Programmable functionality as pulse counter, frequency counter, timer or
• Relay output• Adding/subtracting via 2 separate in-
puts• PNP and NPN sensors can be connec-
ted• Protection degree IP65 (front only)
Dimensions
Electrical connection
KCT1-6SR-C KCT1-6SR-VGeneral specificationsPre-selection singleProgramming keypad-driven menuIndicators/operating meansType 7-segment LED display, redNumber of decades 6Display value digit height 8 mmPre-selection switchableDisplay interval -99999 ... 999999Decimal point 0 to max 3 fractional digitsScale factor 0.0001 ... 99.9999Reset manually or externalKey interlock with "high"-level at terminal "KEY"Electrical specificationsOperating voltage 10 ... 30 V DC 90 ... 250 V ACPower consumption max. 1.2 VA max. 7 VAInputCounting frequency 20 kHz 20 kHzImpedance approx. 10 kOhm approx. 10 kOhmVoltage low: 0 ... 0.2 x Ue
high: 0.6 x Ue ... 30 V DClow: 0 ... 4 V DC
high: 12 ... 30 V DC
Counting method adding or subtracting adding or subtractingOutputRelay 250 V AC, 0.3 ... 3 mA, changeover con-
tact250 V AC, 0.3 ... 3 mA, changeover con-
tactSensor supply - 14.4 ... 28 V DC, 100 mAMechanical specificationsConnection 2 plug-in 7-pin screw terminals
max. core cross-section 0.34 ... 1.5 mm2
Mass approx. 200 g
15.5
80.1
9.3
7.3
max. 10.5
4548
48
3 71 4 5 62
3 71 4 5 62
31 4 52
Connector assignment X1supply voltage and outputs
TerminalNo.123
4
5
6
7
AC version
n.c.n.c.output relay common contact (C)output relay normally open contact (NO)output relay normally closed contact (NC)supply voltage90 ... 250 V ACsupply voltage90 ... 250 V AC
10 ... 30 V DC version
operating voltage10 ... 30 V DC0 V DC (GND)
TerminalNo.45
AC and DC versions
Relay normally closed (NC)Relay normally open (NO)
TerminalNo.1
2
34567
AC version
SensorSupply voltageReference voltage
Counter input ACounter input BReset inputGate circuitInput for key locking
10 ... 30 V DC versionnot connectednot connected
Name
+24 VDC
0 VDC(GND)INP AINP BRESETGATEKEY
Connector assignment X2inputs
AttentionIn the case of selection of and (inverted relay function) the function of terminals 4 and 5 are changed:
3 71 4 5 62
3 71 4 5 62X2
X1
Counter / Timer / Tachometer
Technical Specifications
• Counter frequency up to 20 kHz• 6-digit LED indicator, red• 1 pre-selection• Status LED indication for output and
preselection value• Programmable functionality as pulse
counter, frequency counter, timer or • Relay output• Adding/subtracting via 2 separate inputs• PNP and NPN sensors can be connected
• Counter/Timer/Tachometer• Counter frequency up to 20 kHz• 6-digit LED indicator, red• 1 Pre-selection• Status LED indication for output an pre-
selection value• Display range and preselection range
from -199999 up to 999999Overflow will be evaluated correctly up to 1 decade
• Programmable functionality as pulse counter, frequency counter, timer or
• Relay output• Adding/subtracting via 2 separate in-
puts• PNP and NPN sensors can be connec-
ted• Protection degree IP65 (front only)
Dimensions
Electrical connection
KCT1-6SR-C KCT1-6SR-VGeneral specificationsPre-selection singleProgramming keypad-driven menuIndicators/operating meansType 7-segment LED display, redNumber of decades 6Display value digit height 8 mmPre-selection switchableDisplay interval -99999 ... 999999Decimal point 0 to max 3 fractional digitsScale factor 0.0001 ... 99.9999Reset manually or externalKey interlock with "high"-level at terminal "KEY"Electrical specificationsOperating voltage 10 ... 30 V DC 90 ... 250 V ACPower consumption max. 1.2 VA max. 7 VAInputCounting frequency 20 kHz 20 kHzImpedance approx. 10 kOhm approx. 10 kOhmVoltage low: 0 ... 0.2 x Ue
high: 0.6 x Ue ... 30 V DClow: 0 ... 4 V DC
high: 12 ... 30 V DC
Counting method adding or subtracting adding or subtractingOutputRelay 250 V AC, 0.3 ... 3 mA, changeover con-
tact250 V AC, 0.3 ... 3 mA, changeover con-
tactSensor supply - 14.4 ... 28 V DC, 100 mAMechanical specificationsConnection 2 plug-in 7-pin screw terminals
max. core cross-section 0.34 ... 1.5 mm2
Mass approx. 200 g
15.5
80.1
9.3
7.3
max. 10.5
4548
48
3 71 4 5 62
3 71 4 5 62
31 4 52
Connector assignment X1supply voltage and outputs
TerminalNo.123
4
5
6
7
AC version
n.c.n.c.output relay common contact (C)output relay normally open contact (NO)output relay normally closed contact (NC)supply voltage90 ... 250 V ACsupply voltage90 ... 250 V AC
10 ... 30 V DC version
operating voltage10 ... 30 V DC0 V DC (GND)
TerminalNo.45
AC and DC versions
Relay normally closed (NC)Relay normally open (NO)
TerminalNo.1
2
34567
AC version
SensorSupply voltageReference voltage
Counter input ACounter input BReset inputGate circuitInput for key locking
10 ... 30 V DC versionnot connectednot connected
Name
+24 VDC
0 VDC(GND)INP AINP BRESETGATEKEY
Connector assignment X2inputs
AttentionIn the case of selection of and (inverted relay function) the function of terminals 4 and 5 are changed:
3 71 4 5 62
3 71 4 5 62X2
X1
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
1087Singapore: +65 6779 [email protected]
USA: +1 330 486 [email protected]
Germany: +49 621 [email protected]
Pepperl+Fuchs Groupwww.pepperl-fuchs.com
Subject to modifications without notice Copyright Pepperl+Fuchs
Special Functions Devices
Special Functions Devices
• Counter/Timer/Tachometer• Counter frequency up to 20 kHz• 6-digit LED indicator, red• 1 Pre-selection• Status LED indication for output an pre-
selection value• Display range and preselection range
from -199999 up to 999999Overflow will be evaluated correctly up to 1 decade
• Programmable functionality as pulse counter, frequency counter, timer or
• Relay output• Adding/subtracting via 2 separate in-
puts• PNP and NPN sensors can be connec-
ted• Protection degree IP65 (front only)
Dimensions
Electrical connection
KCT1-6SR-C KCT1-6SR-VGeneral specificationsPre-selection singleProgramming keypad-driven menuIndicators/operating meansType 7-segment LED display, redNumber of decades 6Display value digit height 8 mmPre-selection switchableDisplay interval -99999 ... 999999Decimal point 0 to max 3 fractional digitsScale factor 0.0001 ... 99.9999Reset manually or externalKey interlock with "high"-level at terminal "KEY"Electrical specificationsOperating voltage 10 ... 30 V DC 90 ... 250 V ACPower consumption max. 1.2 VA max. 7 VAInputCounting frequency 20 kHz 20 kHzImpedance approx. 10 kOhm approx. 10 kOhmVoltage low: 0 ... 0.2 x Ue
high: 0.6 x Ue ... 30 V DClow: 0 ... 4 V DC
high: 12 ... 30 V DC
Counting method adding or subtracting adding or subtractingOutputRelay 250 V AC, 0.3 ... 3 mA, changeover con-
tact250 V AC, 0.3 ... 3 mA, changeover con-
tactSensor supply - 14.4 ... 28 V DC, 100 mAMechanical specificationsConnection 2 plug-in 7-pin screw terminals
max. core cross-section 0.34 ... 1.5 mm2
Mass approx. 200 g
15.5
80.1
9.3
7.3
max. 10.5
4548
48
3 71 4 5 62
3 71 4 5 62
31 4 52
Connector assignment X1supply voltage and outputs
TerminalNo.123
4
5
6
7
AC version
n.c.n.c.output relay common contact (C)output relay normally open contact (NO)output relay normally closed contact (NC)supply voltage90 ... 250 V ACsupply voltage90 ... 250 V AC
10 ... 30 V DC version
operating voltage10 ... 30 V DC0 V DC (GND)
TerminalNo.45
AC and DC versions
Relay normally closed (NC)Relay normally open (NO)
TerminalNo.1
2
34567
AC version
SensorSupply voltageReference voltage
Counter input ACounter input BReset inputGate circuitInput for key locking
10 ... 30 V DC versionnot connectednot connected
Name
+24 VDC
0 VDC(GND)INP AINP BRESETGATEKEY
Connector assignment X2inputs
AttentionIn the case of selection of and (inverted relay function) the function of terminals 4 and 5 are changed:
3 71 4 5 62
3 71 4 5 62X2
X1
Wiring Diagrams
Dimensions
• Counter/Timer/Tachometer• Counter frequency up to 20 kHz• 6-digit LED indicator, red• 1 Pre-selection• Status LED indication for output an pre-
selection value• Display range and preselection range
from -199999 up to 999999Overflow will be evaluated correctly up to 1 decade
• Programmable functionality as pulse counter, frequency counter, timer or
• Relay output• Adding/subtracting via 2 separate in-
puts• PNP and NPN sensors can be connec-
ted• Protection degree IP65 (front only)
Dimensions
Electrical connection
KCT1-6SR-C KCT1-6SR-VGeneral specificationsPre-selection singleProgramming keypad-driven menuIndicators/operating meansType 7-segment LED display, redNumber of decades 6Display value digit height 8 mmPre-selection switchableDisplay interval -99999 ... 999999Decimal point 0 to max 3 fractional digitsScale factor 0.0001 ... 99.9999Reset manually or externalKey interlock with "high"-level at terminal "KEY"Electrical specificationsOperating voltage 10 ... 30 V DC 90 ... 250 V ACPower consumption max. 1.2 VA max. 7 VAInputCounting frequency 20 kHz 20 kHzImpedance approx. 10 kOhm approx. 10 kOhmVoltage low: 0 ... 0.2 x Ue
high: 0.6 x Ue ... 30 V DClow: 0 ... 4 V DC
high: 12 ... 30 V DC
Counting method adding or subtracting adding or subtractingOutputRelay 250 V AC, 0.3 ... 3 mA, changeover con-
tact250 V AC, 0.3 ... 3 mA, changeover con-
tactSensor supply - 14.4 ... 28 V DC, 100 mAMechanical specificationsConnection 2 plug-in 7-pin screw terminals
max. core cross-section 0.34 ... 1.5 mm2
Mass approx. 200 g
15.5
80.1
9.3
7.3
max. 10.5
4548
48
3 71 4 5 62
3 71 4 5 62
31 4 52
Connector assignment X1supply voltage and outputs
TerminalNo.123
4
5
6
7
AC version
n.c.n.c.output relay common contact (C)output relay normally open contact (NO)output relay normally closed contact (NC)supply voltage90 ... 250 V ACsupply voltage90 ... 250 V AC
10 ... 30 V DC version
operating voltage10 ... 30 V DC0 V DC (GND)
TerminalNo.45
AC and DC versions
Relay normally closed (NC)Relay normally open (NO)
TerminalNo.1
2
34567
AC version
SensorSupply voltageReference voltage
Counter input ACounter input BReset inputGate circuitInput for key locking
10 ... 30 V DC versionnot connectednot connected
Name
+24 VDC
0 VDC(GND)INP AINP BRESETGATEKEY
Connector assignment X2inputs
AttentionIn the case of selection of and (inverted relay function) the function of terminals 4 and 5 are changed:
3 71 4 5 62
3 71 4 5 62X2
X1
Terminal Connection
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
1088 Singapore: +65 6779 [email protected]
USA: +1 330 486 [email protected]
Germany: +49 621 [email protected]
Pepperl+Fuchs Groupwww.pepperl-fuchs.com
Subject to modifications without notice Copyright Pepperl+Fuchs
Special Functions Devices
Spec
ial F
unct
ions
Dev
ices
• Counter/Timer/Tachometer• 6-digit LED indicator, red• 2 independent pre-select values• RS 232 interface for parameter assign-
ment• Status LED indication for output an pre-
selection value• Display range and preselection range
from -199999 up to 999999Overflow will be evaluated correctly up to 1 decade
• Programmable functionality as pulse counter, frequency counter, timer or
• Relay output• Adding/subtracting via 2 separate in-
puts• PNP and NPN sensors can be connec-
ted• Protection degree IP65 (front only)
Dimensions
Electrical connection
KCT1-6WR/RS232-VGeneral specificationsPre-selection 2-foldProgramming keypad-driven menuIndicators/operating meansType 7-segment LED display, redNumber of decades 6Display value digit height 8 mmPre-selection switchableDisplay interval -999999 ... 999999Decimal point 0 to max 3 fractional digitsScale factor 0.0001 ... 99.9999Reset manually or externalKey interlock with "high"-level at terminal "KEY"Electrical specificationsOperating voltage 90 ... 250 V ACPower consumption max. 7 VAInputInterface RS 232 interface for parameter assignmentCounting frequency 20 kHzImpedance approx. 10 kOhmVoltage low: 0 ... 4 V DC
high: 12 ... 30 V DCCounting method adding or subtractingOutputRelay 250 V AC, 0.3 ... 3 A, 1 changeover contact, 1 normally-openSensor supply 14.4 ... 28 V DC, 100 mAMechanical specificationsConnection 2 plug-in 7-pin screw terminalsMass approx. 200 g
15.5
80.1
9.3
7.3
max. 10.5
4548
48
3 71 4 5 62
3 71 4 5 62
31 4 52
Connection assignment X1Supply voltage and outputs
TerminalNo.123
4
5
6
7
AC version
Output 1 relay contactOutput 1 relay contactOutput 2relay common contact (C)Output 2 relaynormally open contact (NO)Output 2 relaynormally closed contact (NC)Power supply90 ... 250 V ACPower supply90 ... 250 V AC
TerminalNo.45
AC version
Relay normally closed contact (NC)Relay normally open contact (NO)
TerminalNo.12
34567
AC version
Sensor supply voltageReference voltage
Counter input ACounter input BReset inputGate inputInput of push-button lock
Name
+24 V DC0 VDC(GND)INP AINP BRESETGATEKEY
Connection assignment X2Inputs
Connection assignment X3Serial interface
AttentionIn the case of selection of and (inverted relay control) the connections of terminals 4 and 5 are changed:
3 71 4 5 62
3 71 4 5 62X2
X1
31 4 52
X3
• Counter/Timer/Tachometer• 6-digit LED indicator, red• 2 independent pre-select values• RS 232 interface for parameter assign-
ment• Status LED indication for output an pre-
selection value• Display range and preselection range
from -199999 up to 999999Overflow will be evaluated correctly up to 1 decade
• Programmable functionality as pulse counter, frequency counter, timer or
• Relay output• Adding/subtracting via 2 separate in-
puts• PNP and NPN sensors can be connec-
ted• Protection degree IP65 (front only)
Dimensions
Electrical connection
KCT1-6WR/RS232-VGeneral specificationsPre-selection 2-foldProgramming keypad-driven menuIndicators/operating meansType 7-segment LED display, redNumber of decades 6Display value digit height 8 mmPre-selection switchableDisplay interval -999999 ... 999999Decimal point 0 to max 3 fractional digitsScale factor 0.0001 ... 99.9999Reset manually or externalKey interlock with "high"-level at terminal "KEY"Electrical specificationsOperating voltage 90 ... 250 V ACPower consumption max. 7 VAInputInterface RS 232 interface for parameter assignmentCounting frequency 20 kHzImpedance approx. 10 kOhmVoltage low: 0 ... 4 V DC
high: 12 ... 30 V DCCounting method adding or subtractingOutputRelay 250 V AC, 0.3 ... 3 A, 1 changeover contact, 1 normally-openSensor supply 14.4 ... 28 V DC, 100 mAMechanical specificationsConnection 2 plug-in 7-pin screw terminalsMass approx. 200 g
15.5
80.1
9.3
7.3
max. 10.5
4548
48
3 71 4 5 62
3 71 4 5 62
31 4 52
Connection assignment X1Supply voltage and outputs
TerminalNo.123
4
5
6
7
AC version
Output 1 relay contactOutput 1 relay contactOutput 2relay common contact (C)Output 2 relaynormally open contact (NO)Output 2 relaynormally closed contact (NC)Power supply90 ... 250 V ACPower supply90 ... 250 V AC
TerminalNo.45
AC version
Relay normally closed contact (NC)Relay normally open contact (NO)
TerminalNo.12
34567
AC version
Sensor supply voltageReference voltage
Counter input ACounter input BReset inputGate inputInput of push-button lock
Name
+24 V DC0 VDC(GND)INP AINP BRESETGATEKEY
Connection assignment X2Inputs
Connection assignment X3Serial interface
AttentionIn the case of selection of and (inverted relay control) the connections of terminals 4 and 5 are changed:
3 71 4 5 62
3 71 4 5 62X2
X1
31 4 52
X3
Counter / Timer / Tachometer
Technical Specifications
• 6-digit LED indicator, red• 2 independent pre-select values• RS232 interface for parameter assignment• Status LED indication for output an
preselection value• Programmable functionality as pulse
counter, frequency counter, timer or • Relay output• Adding/subtracting via 2 separate inputs• PNP and NPN sensors can be connected
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
1089Singapore: +65 6779 [email protected]
USA: +1 330 486 [email protected]
Germany: +49 621 [email protected]
Pepperl+Fuchs Groupwww.pepperl-fuchs.com
Subject to modifications without notice Copyright Pepperl+Fuchs
Special Functions Devices
Special Functions Devices
Wiring Diagrams
Dimensions
• Counter/Timer/Tachometer• 6-digit LED indicator, red• 2 independent pre-select values• RS 232 interface for parameter assign-
ment• Status LED indication for output an pre-
selection value• Display range and preselection range
from -199999 up to 999999Overflow will be evaluated correctly up to 1 decade
• Programmable functionality as pulse counter, frequency counter, timer or
• Relay output• Adding/subtracting via 2 separate in-
puts• PNP and NPN sensors can be connec-
ted• Protection degree IP65 (front only)
Dimensions
Electrical connection
KCT1-6WR/RS232-VGeneral specificationsPre-selection 2-foldProgramming keypad-driven menuIndicators/operating meansType 7-segment LED display, redNumber of decades 6Display value digit height 8 mmPre-selection switchableDisplay interval -999999 ... 999999Decimal point 0 to max 3 fractional digitsScale factor 0.0001 ... 99.9999Reset manually or externalKey interlock with "high"-level at terminal "KEY"Electrical specificationsOperating voltage 90 ... 250 V ACPower consumption max. 7 VAInputInterface RS 232 interface for parameter assignmentCounting frequency 20 kHzImpedance approx. 10 kOhmVoltage low: 0 ... 4 V DC
high: 12 ... 30 V DCCounting method adding or subtractingOutputRelay 250 V AC, 0.3 ... 3 A, 1 changeover contact, 1 normally-openSensor supply 14.4 ... 28 V DC, 100 mAMechanical specificationsConnection 2 plug-in 7-pin screw terminalsMass approx. 200 g
15.5
80.1
9.3
7.3
max. 10.5
4548
48
3 71 4 5 62
3 71 4 5 62
31 4 52
Connection assignment X1Supply voltage and outputs
TerminalNo.123
4
5
6
7
AC version
Output 1 relay contactOutput 1 relay contactOutput 2relay common contact (C)Output 2 relaynormally open contact (NO)Output 2 relaynormally closed contact (NC)Power supply90 ... 250 V ACPower supply90 ... 250 V AC
TerminalNo.45
AC version
Relay normally closed contact (NC)Relay normally open contact (NO)
TerminalNo.12
34567
AC version
Sensor supply voltageReference voltage
Counter input ACounter input BReset inputGate inputInput of push-button lock
Name
+24 V DC0 VDC(GND)INP AINP BRESETGATEKEY
Connection assignment X2Inputs
Connection assignment X3Serial interface
AttentionIn the case of selection of and (inverted relay control) the connections of terminals 4 and 5 are changed:
3 71 4 5 62
3 71 4 5 62X2
X1
31 4 52
X3
• Counter/Timer/Tachometer• 6-digit LED indicator, red• 2 independent pre-select values• RS 232 interface for parameter assign-
ment• Status LED indication for output an pre-
selection value• Display range and preselection range
from -199999 up to 999999Overflow will be evaluated correctly up to 1 decade
• Programmable functionality as pulse counter, frequency counter, timer or
• Relay output• Adding/subtracting via 2 separate in-
puts• PNP and NPN sensors can be connec-
ted• Protection degree IP65 (front only)
Dimensions
Electrical connection
KCT1-6WR/RS232-VGeneral specificationsPre-selection 2-foldProgramming keypad-driven menuIndicators/operating meansType 7-segment LED display, redNumber of decades 6Display value digit height 8 mmPre-selection switchableDisplay interval -999999 ... 999999Decimal point 0 to max 3 fractional digitsScale factor 0.0001 ... 99.9999Reset manually or externalKey interlock with "high"-level at terminal "KEY"Electrical specificationsOperating voltage 90 ... 250 V ACPower consumption max. 7 VAInputInterface RS 232 interface for parameter assignmentCounting frequency 20 kHzImpedance approx. 10 kOhmVoltage low: 0 ... 4 V DC
high: 12 ... 30 V DCCounting method adding or subtractingOutputRelay 250 V AC, 0.3 ... 3 A, 1 changeover contact, 1 normally-openSensor supply 14.4 ... 28 V DC, 100 mAMechanical specificationsConnection 2 plug-in 7-pin screw terminalsMass approx. 200 g
15.5
80.1
9.3
7.3
max. 10.5
4548
48
3 71 4 5 62
3 71 4 5 62
31 4 52
Connection assignment X1Supply voltage and outputs
TerminalNo.123
4
5
6
7
AC version
Output 1 relay contactOutput 1 relay contactOutput 2relay common contact (C)Output 2 relaynormally open contact (NO)Output 2 relaynormally closed contact (NC)Power supply90 ... 250 V ACPower supply90 ... 250 V AC
TerminalNo.45
AC version
Relay normally closed contact (NC)Relay normally open contact (NO)
TerminalNo.12
34567
AC version
Sensor supply voltageReference voltage
Counter input ACounter input BReset inputGate inputInput of push-button lock
Name
+24 V DC0 VDC(GND)INP AINP BRESETGATEKEY
Connection assignment X2Inputs
Connection assignment X3Serial interface
AttentionIn the case of selection of and (inverted relay control) the connections of terminals 4 and 5 are changed:
3 71 4 5 62
3 71 4 5 62X2
X1
31 4 52
X3
Terminal Connection
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
1090 Singapore: +65 6779 [email protected]
USA: +1 330 486 [email protected]
Germany: +49 621 [email protected]
Pepperl+Fuchs Groupwww.pepperl-fuchs.com
Subject to modifications without notice Copyright Pepperl+Fuchs
Special Functions Devices
Spec
ial F
unct
ions
Dev
ices
• Counter/Timer/Tachometer• Extremely bright, large LED indicator• 1 pre-select value with transistor output• PNP and NPN sensors can be connec-
ted• Adding/subtracting via 2 separate in-
puts• Protection degree IP65 (front only)
Dimensions
Electrical connection
KCT2-6ST-VGeneral specificationsPre-selection singleProgramming keypad-driven menuIndicators/operating meansType 7-segment LED display, redNumber of decades 6Display value digit height 14 mmPre-selection active at counter value ≤ 0Display interval -199999 ... 999999 with suppression of leading zerosDecimal point 0 to max 3 fractional digitsScale factor 0.0001 ... 99.9999Reset manually or externalKey interlock -Electrical specificationsOperating voltage 90 ... 260 V ACPower consumption max. 6 VAInputCounting frequency 30 Hz / 20 kHz (max. 11 kHz when counting with phase discriminator)Impedance 10 kOhmVoltage low: 0 ... 4 V DC ; high: 12 ... 30 V DCCounting method adding or subtractingOutputSensor supply 24 V DC ± 15 % / 100 mAOptocoupler NPN, offener Kollektor und offener Emitter
30 V / 15 mAMechanical specificationsConnection 2-pin and 7-pin plug-in connection terminals, core cross-section ≤ 1.5 mm2
Mass approx. 150 g
Control panel cutout
96
48
44.9
x91.
9
92+0.8
67.1 6.5
4
max. 19
45+
0.6
12
Connection assignment X2
Terminal No. 1 2
AC version
Power supply90 ... 260 V ACPower supply90 ... 260 V AC
Terminal No.1234 5 6 7
AC version
Optocoupler collector output Optocoupler emitter outputSETINP BINP AGND+24 V out
Connection assignment X1
21 3 4 5 6 721
X2X1
Counter / Timer / Tachometer
Technical Specifications
• Extremely bright, large LED indicator• 1 pre-select value with transistor output• PNP and NPN sensors can be connected• Adding/subtracting via 2 separate inputs
• Counter/Timer/Tachometer• Extremely bright, large LED indicator• 1 pre-select value with transistor output• PNP and NPN sensors can be connec-
ted• Adding/subtracting via 2 separate in-
puts• Protection degree IP65 (front only)
Dimensions
Electrical connection
KCT2-6ST-VGeneral specificationsPre-selection singleProgramming keypad-driven menuIndicators/operating meansType 7-segment LED display, redNumber of decades 6Display value digit height 14 mmPre-selection active at counter value ≤ 0Display interval -199999 ... 999999 with suppression of leading zerosDecimal point 0 to max 3 fractional digitsScale factor 0.0001 ... 99.9999Reset manually or externalKey interlock -Electrical specificationsOperating voltage 90 ... 260 V ACPower consumption max. 6 VAInputCounting frequency 30 Hz / 20 kHz (max. 11 kHz when counting with phase discriminator)Impedance 10 kOhmVoltage low: 0 ... 4 V DC ; high: 12 ... 30 V DCCounting method adding or subtractingOutputSensor supply 24 V DC ± 15 % / 100 mAOptocoupler NPN, offener Kollektor und offener Emitter
30 V / 15 mAMechanical specificationsConnection 2-pin and 7-pin plug-in connection terminals, core cross-section ≤ 1.5 mm2
Mass approx. 150 g
Control panel cutout
96
48
44.9
x91.
9
92+0.8
67.1 6.5
4
max. 19
45+
0.6
12
Connection assignment X2
Terminal No. 1 2
AC version
Power supply90 ... 260 V ACPower supply90 ... 260 V AC
Terminal No.1234 5 6 7
AC version
Optocoupler collector output Optocoupler emitter outputSETINP BINP AGND+24 V out
Connection assignment X1
21 3 4 5 6 721
X2X1
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
1091Singapore: +65 6779 [email protected]
USA: +1 330 486 [email protected]
Germany: +49 621 [email protected]
Pepperl+Fuchs Groupwww.pepperl-fuchs.com
Subject to modifications without notice Copyright Pepperl+Fuchs
Special Functions Devices
Special Functions Devices
• Counter/Timer/Tachometer• Extremely bright, large LED indicator• 1 pre-select value with transistor output• PNP and NPN sensors can be connec-
ted• Adding/subtracting via 2 separate in-
puts• Protection degree IP65 (front only)
Dimensions
Electrical connection
KCT2-6ST-VGeneral specificationsPre-selection singleProgramming keypad-driven menuIndicators/operating meansType 7-segment LED display, redNumber of decades 6Display value digit height 14 mmPre-selection active at counter value ≤ 0Display interval -199999 ... 999999 with suppression of leading zerosDecimal point 0 to max 3 fractional digitsScale factor 0.0001 ... 99.9999Reset manually or externalKey interlock -Electrical specificationsOperating voltage 90 ... 260 V ACPower consumption max. 6 VAInputCounting frequency 30 Hz / 20 kHz (max. 11 kHz when counting with phase discriminator)Impedance 10 kOhmVoltage low: 0 ... 4 V DC ; high: 12 ... 30 V DCCounting method adding or subtractingOutputSensor supply 24 V DC ± 15 % / 100 mAOptocoupler NPN, offener Kollektor und offener Emitter
30 V / 15 mAMechanical specificationsConnection 2-pin and 7-pin plug-in connection terminals, core cross-section ≤ 1.5 mm2
Mass approx. 150 g
Control panel cutout
96
48
44.9
x91.
9
92+0.8
67.1 6.5
4
max. 19
45+
0.6
12
Connection assignment X2
Terminal No. 1 2
AC version
Power supply90 ... 260 V ACPower supply90 ... 260 V AC
Terminal No.1234 5 6 7
AC version
Optocoupler collector output Optocoupler emitter outputSETINP BINP AGND+24 V out
Connection assignment X1
21 3 4 5 6 721
X2X1
Wiring Diagrams
Dimensions
• Counter/Timer/Tachometer• Extremely bright, large LED indicator• 1 pre-select value with transistor output• PNP and NPN sensors can be connec-
ted• Adding/subtracting via 2 separate in-
puts• Protection degree IP65 (front only)
Dimensions
Electrical connection
KCT2-6ST-VGeneral specificationsPre-selection singleProgramming keypad-driven menuIndicators/operating meansType 7-segment LED display, redNumber of decades 6Display value digit height 14 mmPre-selection active at counter value ≤ 0Display interval -199999 ... 999999 with suppression of leading zerosDecimal point 0 to max 3 fractional digitsScale factor 0.0001 ... 99.9999Reset manually or externalKey interlock -Electrical specificationsOperating voltage 90 ... 260 V ACPower consumption max. 6 VAInputCounting frequency 30 Hz / 20 kHz (max. 11 kHz when counting with phase discriminator)Impedance 10 kOhmVoltage low: 0 ... 4 V DC ; high: 12 ... 30 V DCCounting method adding or subtractingOutputSensor supply 24 V DC ± 15 % / 100 mAOptocoupler NPN, offener Kollektor und offener Emitter
30 V / 15 mAMechanical specificationsConnection 2-pin and 7-pin plug-in connection terminals, core cross-section ≤ 1.5 mm2
Mass approx. 150 g
Control panel cutout
96
48
44.9
x91.
9
92+0.8
67.1 6.5
4
max. 19
45+
0.6
12
Connection assignment X2
Terminal No. 1 2
AC version
Power supply90 ... 260 V ACPower supply90 ... 260 V AC
Terminal No.1234 5 6 7
AC version
Optocoupler collector output Optocoupler emitter outputSETINP BINP AGND+24 V out
Connection assignment X1
21 3 4 5 6 721
X2X1Terminal Connection
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
1092 Singapore: +65 6779 [email protected]
USA: +1 330 486 [email protected]
Germany: +49 621 [email protected]
Pepperl+Fuchs Groupwww.pepperl-fuchs.com
Subject to modifications without notice Copyright Pepperl+Fuchs
Special Functions Devices
Spec
ial F
unct
ions
Dev
ices
• 1-channel terminal amplifier• NAMUR sensor input• DC 24 V supply voltage• Standard interface for prevention of sig-
nal transmission errors• Switching status indicator, yellow LED• Short-circuit proof electronic output• Low noise sensitivity• Compact terminal housing• Mounting by clipping onto standard
35 mm rail to DIN EN 50022• Protection degree IP20
Dimensions
Electrical connection
KCD2-E KCD2-E1 KCD2-E2 KCD2-E3Indicators/operating meansLED yellow switch outputElectrical specificationsOperating voltage 10 ... 30 V DCOperating current approx. 22 mARipple ≤ 10 %Transfer characteristicsMode of operation NO NC NO NCSwitching frequency 1 kHz 1 kHz 1 kHz 1 kHzInputConnection terminals 1+, 2- terminals 1+, 2- terminals 1+, 2- terminals 1+, 2-Connectable sensor types NAMUR NAMUR NAMUR NAMURShort-circuit current approx. 8 mA approx. 8 mA approx. 8 mA approx. 8 mASensor supply 8 V DC 8 V DC 8 V DC,
max. 9 V DC at input resistance
min. 562 Ω
8 V DC
Switching point 1.2 ... 2.1 mA hys-teresis approx. 0.2
mA
1.2 ... 2.1 mA hys-teresis approx. 0.2
mA
1.2 ... 2.1 mA hys-teresis approx. 0.2
mA
1.2 ... 2.1 mA hys-teresis approx. 0.2
mALead monitoring without without without withoutTrip value 1 kHz 1 kHz 1 kHz 1 kHzOutputConnection terminal 4- terminal 4- terminal 4+ terminal 4+Current 200 mA short-cir-
cuit proof200 mA short-cir-
cuit proof200 mA short-cir-
cuit proof200 mA short-cir-
cuit proofTransistor NPN NPN PNP PNPMechanical specificationsConnection self-opening apparatus connection terminals, max. core cross-section 0.34 ... 2.5
mm2
Mass 60 g
4020
60
54 6
21 3
LED
5+6-4+
1+ 2-
1+ 2- 3
Supplyvoltage
Output
Input
Sensor
I ≤0.1 mA
• 1-channel terminal amplifier• NAMUR sensor input• DC 24 V supply voltage• Standard interface for prevention of sig-
nal transmission errors• Switching status indicator, yellow LED• Short-circuit proof electronic output• Low noise sensitivity• Compact terminal housing• Mounting by clipping onto standard
35 mm rail to DIN EN 50022• Protection degree IP20
Dimensions
Electrical connection
KCD2-E KCD2-E1 KCD2-E2 KCD2-E3Indicators/operating meansLED yellow switch outputElectrical specificationsOperating voltage 10 ... 30 V DCOperating current approx. 22 mARipple ≤ 10 %Transfer characteristicsMode of operation NO NC NO NCSwitching frequency 1 kHz 1 kHz 1 kHz 1 kHzInputConnection terminals 1+, 2- terminals 1+, 2- terminals 1+, 2- terminals 1+, 2-Connectable sensor types NAMUR NAMUR NAMUR NAMURShort-circuit current approx. 8 mA approx. 8 mA approx. 8 mA approx. 8 mASensor supply 8 V DC 8 V DC 8 V DC,
max. 9 V DC at input resistance
min. 562 Ω
8 V DC
Switching point 1.2 ... 2.1 mA hys-teresis approx. 0.2
mA
1.2 ... 2.1 mA hys-teresis approx. 0.2
mA
1.2 ... 2.1 mA hys-teresis approx. 0.2
mA
1.2 ... 2.1 mA hys-teresis approx. 0.2
mALead monitoring without without without withoutTrip value 1 kHz 1 kHz 1 kHz 1 kHzOutputConnection terminal 4- terminal 4- terminal 4+ terminal 4+Current 200 mA short-cir-
cuit proof200 mA short-cir-
cuit proof200 mA short-cir-
cuit proof200 mA short-cir-
cuit proofTransistor NPN NPN PNP PNPMechanical specificationsConnection self-opening apparatus connection terminals, max. core cross-section 0.34 ... 2.5
mm2
Mass 60 g
4020
60
54 6
21 3
LED
5+6-4+
1+ 2-
1+ 2- 3
Supplyvoltage
Output
Input
Sensor
I ≤0.1 mA
Terminal Amplifier/Converter
Technical Specifications
• 1 -channel terminal amplifier• NAMUR sensor input – NPN or PNP output• DC 24 V supply voltage• Switching status indicator, yellow LED• Short-circuit proof electronic output• Compact terminal housing• Mounting by clipping onto standard
35 mm rail
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
1093Singapore: +65 6779 [email protected]
USA: +1 330 486 [email protected]
Germany: +49 621 [email protected]
Pepperl+Fuchs Groupwww.pepperl-fuchs.com
Subject to modifications without notice Copyright Pepperl+Fuchs
Special Functions Devices
Special Functions Devices
Wiring Diagrams
Dimensions
• 1-channel terminal amplifier• NAMUR sensor input• DC 24 V supply voltage• Standard interface for prevention of sig-
nal transmission errors• Switching status indicator, yellow LED• Short-circuit proof electronic output• Low noise sensitivity• Compact terminal housing• Mounting by clipping onto standard
35 mm rail to DIN EN 50022• Protection degree IP20
Dimensions
Electrical connection
KCD2-E KCD2-E1 KCD2-E2 KCD2-E3Indicators/operating meansLED yellow switch outputElectrical specificationsOperating voltage 10 ... 30 V DCOperating current approx. 22 mARipple ≤ 10 %Transfer characteristicsMode of operation NO NC NO NCSwitching frequency 1 kHz 1 kHz 1 kHz 1 kHzInputConnection terminals 1+, 2- terminals 1+, 2- terminals 1+, 2- terminals 1+, 2-Connectable sensor types NAMUR NAMUR NAMUR NAMURShort-circuit current approx. 8 mA approx. 8 mA approx. 8 mA approx. 8 mASensor supply 8 V DC 8 V DC 8 V DC,
max. 9 V DC at input resistance
min. 562 Ω
8 V DC
Switching point 1.2 ... 2.1 mA hys-teresis approx. 0.2
mA
1.2 ... 2.1 mA hys-teresis approx. 0.2
mA
1.2 ... 2.1 mA hys-teresis approx. 0.2
mA
1.2 ... 2.1 mA hys-teresis approx. 0.2
mALead monitoring without without without withoutTrip value 1 kHz 1 kHz 1 kHz 1 kHzOutputConnection terminal 4- terminal 4- terminal 4+ terminal 4+Current 200 mA short-cir-
cuit proof200 mA short-cir-
cuit proof200 mA short-cir-
cuit proof200 mA short-cir-
cuit proofTransistor NPN NPN PNP PNPMechanical specificationsConnection self-opening apparatus connection terminals, max. core cross-section 0.34 ... 2.5
mm2
Mass 60 g
4020
60
54 6
21 3
LED
5+6-4+
1+ 2-
1+ 2- 3
Supplyvoltage
Output
Input
Sensor
I ≤0.1 mA
Terminal Connection
•1-
chan
nel
ter
min
al a
mp
lifie
r•
NA
MU
R s
enso
r in
pu
t•
DC
24
V s
up
ply
vo
ltag
e•
Sta
nd
ard
inte
rfac
e fo
r p
reve
nti
on
of s
ig-
nal
tra
nsm
issi
on
err
ors
•S
wit
chin
g s
tatu
s in
dic
ato
r, y
ello
w L
ED
•S
ho
rt-c
ircu
it p
roo
f el
ectr
on
ic o
utp
ut
•L
ow
no
ise
sen
siti
vity
•C
om
pac
t te
rmin
al h
ou
sin
g•
Mo
un
tin
g b
y cl
ipp
ing
on
to s
tan
dar
d
35m
m r
ail t
o D
INE
N50
022
•P
rote
ctio
n d
egre
e IP
20
Dim
ensi
on
s
Ele
ctri
cal c
on
nec
tio
n
KC
D2-
EK
CD
2-E
1K
CD
2-E
2K
CD
2-E
3In
dica
tors
/ope
ratin
g m
ean
sLE
D y
ello
w
switc
h o
utpu
tE
lect
rica
l sp
ecifi
cati
ons
Ope
ratin
g vo
ltage
10
...
30 V
DC
Ope
ratin
g cu
rren
t ap
prox
. 22
mA
Rip
ple
≤ 10
%Tr
ansf
er c
har
acte
rist
ics
Mod
e of
ope
ratio
n N
ON
CN
ON
CS
witc
hing
freq
uenc
y 1
kHz
1 kH
z1
kHz
1 kH
zIn
put
Con
nect
ion
term
inal
s 1+
, 2-
term
inal
s 1+
, 2-
term
inal
s 1+
, 2-
term
inal
s 1+
, 2-
Con
nect
able
sen
sor
type
s N
AM
UR
NA
MU
RN
AM
UR
NA
MU
RS
hort
-circ
uit c
urre
nt
appr
ox. 8
mA
appr
ox. 8
mA
appr
ox. 8
mA
appr
ox. 8
mA
Sen
sor
supp
ly
8 V
DC
8 V
DC
8 V
DC
, m
ax. 9
VD
C a
t in
put r
esis
tanc
e m
in. 5
62Ω
8 V
DC
Sw
itchi
ng p
oint
1.
2 ...
2.1
mA
hys
-te
resi
s ap
prox
. 0.2
m
A
1.2
... 2
.1 m
A h
ys-
tere
sis
appr
ox. 0
.2
mA
1.2
... 2
.1 m
A h
ys-
tere
sis
appr
ox. 0
.2
mA
1.2
... 2
.1 m
A h
ys-
tere
sis
appr
ox. 0
.2
mA
Lead
mon
itorin
g w
ithou
tw
ithou
tw
itho
utw
itho
utT
rip v
alue
1
kHz
1 kH
z1
kHz
1 kH
zO
utp
utC
onne
ctio
n te
rmin
al 4
-te
rmin
al 4
-te
rmin
al 4
+te
rmin
al 4
+C
urre
nt
200
mA
sho
rt-c
ir-cu
it pr
oof
200
mA
sho
rt-c
ir-cu
it pr
oof
200
mA
sho
rt-c
ir-cu
it pr
oof
200
mA
sho
rt-c
ir-cu
it pr
oof
Tra
nsis
tor
NP
NN
PN
PN
PP
NP
Mec
han
ical
spe
cific
atio
nsC
onne
ctio
n se
lf-op
enin
g ap
para
tus
conn
ectio
n te
rmin
als,
max
. cor
e cr
oss-
sect
ion
0.34
...
2.5
mm
2
Mas
s 60
g
4020
60
54
6
21
3
LED
5+6-
4+
1+2-
1+2-
3
Sup
ply
volta
geO
utpu
t
Inpu
t
Sen
sor
I ≤0.
1 m
A
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
1094 Singapore: +65 6779 [email protected]
USA: +1 330 486 [email protected]
Germany: +49 621 [email protected]
Pepperl+Fuchs Groupwww.pepperl-fuchs.com
Subject to modifications without notice Copyright Pepperl+Fuchs
Special Functions Devices
Spec
ial F
unct
ions
Dev
ices
Terminal Amplifier/Converter
• 1-channel terminal amplifier• NAMUR sensor input• DC 24 V supply voltage• Standard interface for prevention of sig-
nal transmission errors• Switching status indicator, yellow LED• Lead breakage monitoring: The lead
breakage monitoring can be disconnec-ted by bridging terminals 1 and 3 (When using a mechanical contact a 10 kOhm resistor is required in parallel circuit)
• Short-circuit proof electronic output• Low noise sensitivity• Compact terminal housing• Mounting by clipping onto standard
35 mm rail to DIN EN 50022• Protection degree IP20
Dimensions
Electrical connection
KCD2-EL KCD2-E2LIndicators/operating meansLED yellow switch outputElectrical specificationsOperating voltage 10 ... 30 V DCOperating current approx. 22 mARipple ≤ 10 %Transfer characteristicsMode of operation NOSwitching frequency 1 kHzInputConnection terminals 1+, 2-Connectable sensor types NAMURShort-circuit current approx. 8 mASensor supply 8 V DCSwitching point 1.2 ... 2.1 mA hysteresis approx. 0.2 mALead monitoring withTrip value 1 kHzOutputConnection terminal 4- terminal 4+Current 200 mA short-circuit proof 200 mA short-circuit proofTransistor NPN PNPMechanical specificationsConnection self-opening apparatus connection terminals, max. core cross-section 0.34 ... 2.5
mm2
Mass 60 g
4020
60
54 6
21 3
LED
Supplyvoltage
Output
Input
Lead breakagemonitoring
Sensor
I ≤0.1 mA
5+6-4-
1+
1+
2-
1+ 2- 3
3
Technical Specifications
• 1-channel terminal amplifier• NAMUR sensor input – NPN or PNP output• DC 24 V supply voltage• Switching status indicator, yellow LED• Lead breakage monitoring• Short-circuit proof electronic output• Low noise sensitivity• Compact terminal housing• Mounting by clipping onto standard
35 mm rail to DINEN50022
• 1-channel terminal amplifier• NAMUR sensor input• DC 24 V supply voltage• Standard interface for prevention of sig-
nal transmission errors• Switching status indicator, yellow LED• Lead breakage monitoring: The lead
breakage monitoring can be disconnec-ted by bridging terminals 1 and 3 (When using a mechanical contact a 10 kOhm resistor is required in parallel circuit)
• Short-circuit proof electronic output• Low noise sensitivity• Compact terminal housing• Mounting by clipping onto standard
35 mm rail to DIN EN 50022• Protection degree IP20
Dimensions
Electrical connection
KCD2-EL KCD2-E2LIndicators/operating meansLED yellow switch outputElectrical specificationsOperating voltage 10 ... 30 V DCOperating current approx. 22 mARipple ≤ 10 %Transfer characteristicsMode of operation NOSwitching frequency 1 kHzInputConnection terminals 1+, 2-Connectable sensor types NAMURShort-circuit current approx. 8 mASensor supply 8 V DCSwitching point 1.2 ... 2.1 mA hysteresis approx. 0.2 mALead monitoring withTrip value 1 kHzOutputConnection terminal 4- terminal 4+Current 200 mA short-circuit proof 200 mA short-circuit proofTransistor NPN PNPMechanical specificationsConnection self-opening apparatus connection terminals, max. core cross-section 0.34 ... 2.5
mm2
Mass 60 g
4020
60
54 6
21 3
LED
Supplyvoltage
Output
Input
Lead breakagemonitoring
Sensor
I ≤0.1 mA
5+6-4-
1+
1+
2-
1+ 2- 3
3
Note: Lead breakage monitoring can be disabled via jumper connection between terminals 1 and 3.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
1095Singapore: +65 6779 [email protected]
USA: +1 330 486 [email protected]
Germany: +49 621 [email protected]
Pepperl+Fuchs Groupwww.pepperl-fuchs.com
Subject to modifications without notice Copyright Pepperl+Fuchs
Special Functions Devices
Special Functions Devices
•1-
chan
nel
ter
min
al a
mp
lifie
r•
NA
MU
R s
enso
r in
pu
t•
DC
24
V s
up
ply
vo
ltag
e•
Sta
nd
ard
inte
rfac
e fo
r p
reve
nti
on
of s
ig-
nal
tra
nsm
issi
on
err
ors
•S
wit
chin
g s
tatu
s in
dic
ato
r, y
ello
w L
ED
•L
ead
bre
akag
e m
on
ito
rin
g:
Th
e le
ad
bre
akag
e m
on
ito
rin
g c
an b
e d
isco
nn
ec-
ted
by
bri
dg
ing
term
inal
s 1
and
3 (W
hen
u
sin
g a
mec
han
ical
co
nta
ct a
10
kOh
m
resi
sto
r is
req
uir
ed in
par
alle
l cir
cuit
)•
Sh
ort
-cir
cuit
pro
of
elec
tro
nic
ou
tpu
t•
Lo
w n
ois
e se
nsi
tivi
ty•
Co
mp
act
term
inal
ho
usi
ng
•M
ou
nti
ng
by
clip
pin
g o
nto
sta
nd
ard
35
mm
rai
l to
DIN
EN
5002
2•
Pro
tect
ion
deg
ree
IP20
Dim
ensi
on
s
Ele
ctri
cal c
on
nec
tio
n
KC
D2-
EL
KC
D2-
E2L
Ind
icat
ors
/op
erat
ing
mea
ns
LED
yel
low
sw
itch
outp
utE
lect
rica
l spe
cific
atio
ns
Ope
ratin
g vo
ltage
10
... 3
0 V
DC
Ope
ratin
g cu
rren
t ap
prox
. 22
mA
Rip
ple
≤ 10
%T
ran
sfer
cha
ract
eris
tics
Mod
e of
ope
ratio
n N
OS
witc
hing
freq
uenc
y 1
kHz
Inp
utC
onne
ctio
n te
rmin
als
1+,
2-C
onne
ctab
le s
enso
r ty
pes
NA
MU
RS
hort
-circ
uit c
urre
nt
appr
ox. 8
mA
Sen
sor
supp
ly
8 V
DC
Sw
itchi
ng p
oint
1.
2 ...
2.1
mA
hys
tere
sis
appr
ox. 0
.2 m
ALe
ad m
onito
ring
with
Trip
val
ue
1 kH
zO
utp
ut
Con
nect
ion
term
inal
4-
term
inal
4+
Cur
rent
20
0 m
A s
hort
-circ
uit p
roof
200
mA
sho
rt-c
ircui
t pro
ofT
rans
isto
r N
PN
PN
PM
echa
nic
al s
pec
ifica
tions
Con
nect
ion
self-
open
ing
appa
ratu
s co
nnec
tion
term
inal
s, m
ax. c
ore
cros
s-se
ctio
n 0.
34 ..
. 2.5
m
m2
Mas
s 60
g
4020
60
54
6
21
3
LED
Sup
ply
volta
geO
utpu
t
Inpu
t
Lead
bre
akag
em
onito
ring
Sen
sor
I ≤0.
1 m
A
5+6-
4-
1+ 1+
2-
1+2-
33
Wiring Diagrams
Dimensions
• 1-channel terminal amplifier• NAMUR sensor input• DC 24 V supply voltage• Standard interface for prevention of sig-
nal transmission errors• Switching status indicator, yellow LED• Lead breakage monitoring: The lead
breakage monitoring can be disconnec-ted by bridging terminals 1 and 3 (When using a mechanical contact a 10 kOhm resistor is required in parallel circuit)
• Short-circuit proof electronic output• Low noise sensitivity• Compact terminal housing• Mounting by clipping onto standard
35 mm rail to DIN EN 50022• Protection degree IP20
Dimensions
Electrical connection
KCD2-EL KCD2-E2LIndicators/operating meansLED yellow switch outputElectrical specificationsOperating voltage 10 ... 30 V DCOperating current approx. 22 mARipple ≤ 10 %Transfer characteristicsMode of operation NOSwitching frequency 1 kHzInputConnection terminals 1+, 2-Connectable sensor types NAMURShort-circuit current approx. 8 mASensor supply 8 V DCSwitching point 1.2 ... 2.1 mA hysteresis approx. 0.2 mALead monitoring withTrip value 1 kHzOutputConnection terminal 4- terminal 4+Current 200 mA short-circuit proof 200 mA short-circuit proofTransistor NPN PNPMechanical specificationsConnection self-opening apparatus connection terminals, max. core cross-section 0.34 ... 2.5
mm2
Mass 60 g
4020
6054 6
21 3
LED
Supplyvoltage
Output
Input
Lead breakagemonitoring
Sensor
I ≤0.1 mA
5+6-4-
1+
1+
2-
1+ 2- 3
3
Terminal Connection
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
1096 Singapore: +65 6779 [email protected]
USA: +1 330 486 [email protected]
Germany: +49 621 [email protected]
Pepperl+Fuchs Groupwww.pepperl-fuchs.com
Subject to modifications without notice Copyright Pepperl+Fuchs
Special Functions Devices
Spec
ial F
unct
ions
Dev
ices
• Relay output with 1 pole, indication of the switching state LED yellow
• Free-wheeling diode• Compact terminal housing• Mounting by clipping onto standard
35 mm rail to DIN EN 50022• Protection degree IP20
Dimensions
Electrical connection
KCD2-RIndicators/operating meansLED yellow switch outputElectrical specificationsOperating voltage 24 V DC ± 15 %Operating current 16 mARipple ≤ 10 %InputConnection terminals 2+, 3-Connectable sensor types PNP or NPN 3-wire sensorsOutputSwitching frequency ≤ 10 HzRelay 1 changeover contactContact loading 250 V AC/2A/cos φ≥0.7
30 V DC/2 A resistive loadMechanical life ≥108 switching cyclesMechanical specificationsConnection self-opening apparatus connection terminals,
max. core cross-section 0.34 ... 2.5 mm2
Mass 60 g
4020
60
54 6
21 3
LED
564
2+3-
Output
Input
Sensor Output Converter
Technical Specifications
• Relay output with 1 pole, indication of the switching state LED yellow
• Free-wheeling diode• Compact terminal housing• Mounting by clipping onto
standard 35mm• PNPN or PNP input
• Relay output with 1 pole, indication of the switching state LED yellow
• Free-wheeling diode• Compact terminal housing• Mounting by clipping onto standard
35 mm rail to DIN EN 50022• Protection degree IP20
Dimensions
Electrical connection
KCD2-RIndicators/operating meansLED yellow switch outputElectrical specificationsOperating voltage 24 V DC ± 15 %Operating current 16 mARipple ≤ 10 %InputConnection terminals 2+, 3-Connectable sensor types PNP or NPN 3-wire sensorsOutputSwitching frequency ≤ 10 HzRelay 1 changeover contactContact loading 250 V AC/2A/cos φ≥0.7
30 V DC/2 A resistive loadMechanical life ≥108 switching cyclesMechanical specificationsConnection self-opening apparatus connection terminals,
max. core cross-section 0.34 ... 2.5 mm2
Mass 60 g
4020
60
54 6
21 3
LED
564
2+3-
Output
Input
Note: This device can be used to convert NPN/PNP sensor outputs to relay contact output. The sensor must be supplied from a separate power supply unit.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
1097Singapore: +65 6779 [email protected]
USA: +1 330 486 [email protected]
Germany: +49 621 [email protected]
Pepperl+Fuchs Groupwww.pepperl-fuchs.com
Subject to modifications without notice Copyright Pepperl+Fuchs
Special Functions Devices
Special Functions Devices
• Relay output with 1 pole, indication of the switching state LED yellow
• Free-wheeling diode• Compact terminal housing• Mounting by clipping onto standard
35 mm rail to DIN EN 50022• Protection degree IP20
Dimensions
Electrical connection
KCD2-RIndicators/operating meansLED yellow switch outputElectrical specificationsOperating voltage 24 V DC ± 15 %Operating current 16 mARipple ≤ 10 %InputConnection terminals 2+, 3-Connectable sensor types PNP or NPN 3-wire sensorsOutputSwitching frequency ≤ 10 HzRelay 1 changeover contactContact loading 250 V AC/2A/cos φ≥0.7
30 V DC/2 A resistive loadMechanical life ≥108 switching cyclesMechanical specificationsConnection self-opening apparatus connection terminals,
max. core cross-section 0.34 ... 2.5 mm2
Mass 60 g
4020
6054 6
21 3
LED
564
2+3-
Output
Input
Wiring Diagrams
Dimensions
• Relay output with 1 pole, indication of the switching state LED yellow
• Free-wheeling diode• Compact terminal housing• Mounting by clipping onto standard
35 mm rail to DIN EN 50022• Protection degree IP20
Dimensions
Electrical connection
KCD2-RIndicators/operating meansLED yellow switch outputElectrical specificationsOperating voltage 24 V DC ± 15 %Operating current 16 mARipple ≤ 10 %InputConnection terminals 2+, 3-Connectable sensor types PNP or NPN 3-wire sensorsOutputSwitching frequency ≤ 10 HzRelay 1 changeover contactContact loading 250 V AC/2A/cos φ≥0.7
30 V DC/2 A resistive loadMechanical life ≥108 switching cyclesMechanical specificationsConnection self-opening apparatus connection terminals,
max. core cross-section 0.34 ... 2.5 mm2
Mass 60 g
4020
6054 6
21 3
LED
564
2+3-
Output
Input
Terminal Connection
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
1098 Singapore: +65 6779 [email protected]
USA: +1 330 486 [email protected]
Germany: +49 621 [email protected]
Pepperl+Fuchs Groupwww.pepperl-fuchs.com
Subject to modifications without notice Copyright Pepperl+Fuchs
Special Functions Devices
Spec
ial F
unct
ions
Dev
ices
Speed Monitoring
• Speed monitoring up to;40;kHz• 1 pre-select value with relay output and
LED indicator• 2-, 3-, 4-wire and NAMUR sensors as
well as rotary encoder connectable• Start-up delay• Menu driven operation via 4 front keys• Period measurement• Output signal can be inverted• Display devices can be set between
0.1 ... 2.5 sec.
Dimensions
Electrical connection
KFU8-DW-1.DSupplyRated voltage 196 ... 264 V AC ; 98 ... 132 V AC; 47 ... 63 Hz
20.4 ... 28 V DCPower consumption AC: < 5 VA
DC: < 5 WIndicators/operating meansType 4-digit 7-segment display, red, 7 mm digit heightDisplay interval 0.002 ... 9999 Hz or
0,01 ... 9999 min-1
Parameter assignment keypad-driven menuSwitching state LED yellow, 3 mmInput 1Connectable sensor types NAMUR sensors according to DIN EN 60947-5-6Open loop voltage 8.2 V DCShort-circuit current 6.5 mASwitching point 1.2 ... 2.1 mA Switching hysteresis approx. 0.2 mAInput 2Connectable sensor types Two, three, or four-wire proximity switch, incremental rotary encoder, or externally
generated pulses 16 ... 30 VSensor supply 19 ... 28 V DC non-stabilised; ≤ 30 mA short-circuit proofSwitching point high: 16 ... 30 V DC; max.10 mA due to integrated constant current sink; Ri ≅ 3 kΩ
low: 0 ... 6 V DCInput frequency 0.002 ... 40000 Hz, pulse length/duration: ≥ 12µsInput 3Start-up override Triggering by external signal 16 ... 30 V or Place jumper between terminals 2/3 or
by switching on supply voltage (terminal 2 and terminal 3 permanently bridged)Jumpering time 0.1 ... 999.9 s (External trigger signal)OutputRelay 1 changeover contact
NO, NC, COMSensor supply 24 V DC ± 10 %, 30 mA , short-circuit proofContact loading 250 V AC/2 A/ cos φ ≥ 0.7
40 V DC/2 ATransfer characteristicsMeasuring error 0 ... 40000 Hz: ≤ ±0,10%
Display: ±1 digitTimer function Rise/fall delay, wipe contact, pulse extensionTime 0 ... 999.9 s ; Direction of action reversibleAmbient conditionsAmbient temperature -25 ... 60 °C (248 ... 333 K)Mechanical specificationsProtection degree IP20Connection coded, removable terminals , max. core cross-section 0.34 ... 2.5 mm2
Mode
Output Drehzahlwächter Speed monitor
Enter
+
–
1 2 3 4 5 6
13 14 15 16 17 187 8 9 10 11 12
PEPPERL+FUCHS GERMANY
Control keys
7-segment-display
Yellow LED, Relay switch state indication
107
93
115
L+
L–89
L+
L–
151413
7
L+
L–89
L+
L– 13
71514
L+
L–
151413
7 L+
L– 13
71514
L+
L–
151413
7 L+
L–
L+16-30 V
0 V L–
1514
1514
13
7
yellow
NAMUR Sensor
NAMUR Encoder
DC-3-wire sensor, PNP
DC-3-wire sensor, NPN
DC-2-wire sensor, PNP
DC-2-wire sensor, NPN
Encoder, push-pull
Encoder, push-pull
Power supply 24 V DC
Power supply 230 V AC
Power supply 115 V AC
Not connected
Sensor power supply GND
Sensor power supply GND
Sensor power supply 24 V DC
Sensor power supply 24 V DC
Trigger input for start-up bypass
External trigger signal
Bridge fitted: start-up bypass triggered by switching on the power supply
Relay output
External rectangular signal
Galvanically isolated input
9NAMUR L+
NAMUR L-8
73
2
1
15
14
13
6
COM
NC
NO
4L+
5L-
16L1 (230 V)
17L1 (115 V)
18N
12
11
10
Technical Specifications
• Speed monitoring up to 40 kHz• 1 pre-select value with relay output and
LED indicator• 2-, 3-, 4-wire and NAMUR sensors as
well as rotary encoder connectable• Start-up delay• Menu driven operation via 4 front keys• Period measurement• Output signal can be inverted• Display devices can be set between
0.1...2.5 sec.
• Speed monitoring up to;40;kHz• 1 pre-select value with relay output and
LED indicator• 2-, 3-, 4-wire and NAMUR sensors as
well as rotary encoder connectable• Start-up delay• Menu driven operation via 4 front keys• Period measurement• Output signal can be inverted• Display devices can be set between
0.1 ... 2.5 sec.
Dimensions
Electrical connection
KFU8-DW-1.DSupplyRated voltage 196 ... 264 V AC ; 98 ... 132 V AC; 47 ... 63 Hz
20.4 ... 28 V DCPower consumption AC: < 5 VA
DC: < 5 WIndicators/operating meansType 4-digit 7-segment display, red, 7 mm digit heightDisplay interval 0.002 ... 9999 Hz or
0,01 ... 9999 min-1
Parameter assignment keypad-driven menuSwitching state LED yellow, 3 mmInput 1Connectable sensor types NAMUR sensors according to DIN EN 60947-5-6Open loop voltage 8.2 V DCShort-circuit current 6.5 mASwitching point 1.2 ... 2.1 mA Switching hysteresis approx. 0.2 mAInput 2Connectable sensor types Two, three, or four-wire proximity switch, incremental rotary encoder, or externally
generated pulses 16 ... 30 VSensor supply 19 ... 28 V DC non-stabilised; ≤ 30 mA short-circuit proofSwitching point high: 16 ... 30 V DC; max.10 mA due to integrated constant current sink; Ri ≅ 3 kΩ
low: 0 ... 6 V DCInput frequency 0.002 ... 40000 Hz, pulse length/duration: ≥ 12µsInput 3Start-up override Triggering by external signal 16 ... 30 V or Place jumper between terminals 2/3 or
by switching on supply voltage (terminal 2 and terminal 3 permanently bridged)Jumpering time 0.1 ... 999.9 s (External trigger signal)OutputRelay 1 changeover contact
NO, NC, COMSensor supply 24 V DC ± 10 %, 30 mA , short-circuit proofContact loading 250 V AC/2 A/ cos φ ≥ 0.7
40 V DC/2 ATransfer characteristicsMeasuring error 0 ... 40000 Hz: ≤ ±0,10%
Display: ±1 digitTimer function Rise/fall delay, wipe contact, pulse extensionTime 0 ... 999.9 s ; Direction of action reversibleAmbient conditionsAmbient temperature -25 ... 60 °C (248 ... 333 K)Mechanical specificationsProtection degree IP20Connection coded, removable terminals , max. core cross-section 0.34 ... 2.5 mm2
Mode
Output Drehzahlwächter Speed monitor
Enter
+
–
1 2 3 4 5 6
13 14 15 16 17 187 8 9 10 11 12
PEPPERL+FUCHS GERMANY
Control keys
7-segment-display
Yellow LED, Relay switch state indication
107
93
115
L+
L–89
L+
L–
151413
7
L+
L–89
L+
L– 13
71514
L+
L–
151413
7 L+
L– 13
71514
L+
L–
151413
7 L+
L–
L+16-30 V
0 V L–
1514
1514
13
7
yellow
NAMUR Sensor
NAMUR Encoder
DC-3-wire sensor, PNP
DC-3-wire sensor, NPN
DC-2-wire sensor, PNP
DC-2-wire sensor, NPN
Encoder, push-pull
Encoder, push-pull
Power supply 24 V DC
Power supply 230 V AC
Power supply 115 V AC
Not connected
Sensor power supply GND
Sensor power supply GND
Sensor power supply 24 V DC
Sensor power supply 24 V DC
Trigger input for start-up bypass
External trigger signal
Bridge fitted: start-up bypass triggered by switching on the power supply
Relay output
External rectangular signal
Galvanically isolated input
9NAMUR L+
NAMUR L-8
73
2
1
15
14
13
6
COM
NC
NO
4L+
5L-
16L1 (230 V)
17L1 (115 V)
18N
12
11
10
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
1099Singapore: +65 6779 [email protected]
USA: +1 330 486 [email protected]
Germany: +49 621 [email protected]
Pepperl+Fuchs Groupwww.pepperl-fuchs.com
Subject to modifications without notice Copyright Pepperl+Fuchs
Special Functions Devices
Special Functions Devices
Dimensions
• Speed monitoring up to;40;kHz• 1 pre-select value with relay output and
LED indicator• 2-, 3-, 4-wire and NAMUR sensors as
well as rotary encoder connectable• Start-up delay• Menu driven operation via 4 front keys• Period measurement• Output signal can be inverted• Display devices can be set between
0.1 ... 2.5 sec.
Dimensions
Electrical connection
KFU8-DW-1.DSupplyRated voltage 196 ... 264 V AC ; 98 ... 132 V AC; 47 ... 63 Hz
20.4 ... 28 V DCPower consumption AC: < 5 VA
DC: < 5 WIndicators/operating meansType 4-digit 7-segment display, red, 7 mm digit heightDisplay interval 0.002 ... 9999 Hz or
0,01 ... 9999 min-1
Parameter assignment keypad-driven menuSwitching state LED yellow, 3 mmInput 1Connectable sensor types NAMUR sensors according to DIN EN 60947-5-6Open loop voltage 8.2 V DCShort-circuit current 6.5 mASwitching point 1.2 ... 2.1 mA Switching hysteresis approx. 0.2 mAInput 2Connectable sensor types Two, three, or four-wire proximity switch, incremental rotary encoder, or externally
generated pulses 16 ... 30 VSensor supply 19 ... 28 V DC non-stabilised; ≤ 30 mA short-circuit proofSwitching point high: 16 ... 30 V DC; max.10 mA due to integrated constant current sink; Ri ≅ 3 kΩ
low: 0 ... 6 V DCInput frequency 0.002 ... 40000 Hz, pulse length/duration: ≥ 12µsInput 3Start-up override Triggering by external signal 16 ... 30 V or Place jumper between terminals 2/3 or
by switching on supply voltage (terminal 2 and terminal 3 permanently bridged)Jumpering time 0.1 ... 999.9 s (External trigger signal)OutputRelay 1 changeover contact
NO, NC, COMSensor supply 24 V DC ± 10 %, 30 mA , short-circuit proofContact loading 250 V AC/2 A/ cos φ ≥ 0.7
40 V DC/2 ATransfer characteristicsMeasuring error 0 ... 40000 Hz: ≤ ±0,10%
Display: ±1 digitTimer function Rise/fall delay, wipe contact, pulse extensionTime 0 ... 999.9 s ; Direction of action reversibleAmbient conditionsAmbient temperature -25 ... 60 °C (248 ... 333 K)Mechanical specificationsProtection degree IP20Connection coded, removable terminals , max. core cross-section 0.34 ... 2.5 mm2
Mode
Output Drehzahlwächter Speed monitor
Enter
+
–
1 2 3 4 5 6
13 14 15 16 17 187 8 9 10 11 12
PEPPERL+FUCHS GERMANY
Control keys
7-segment-display
Yellow LED, Relay switch state indication
107
93
115
L+
L–89
L+
L–
151413
7
L+
L–89
L+
L– 13
71514
L+
L–
151413
7 L+
L– 13
71514
L+
L–
151413
7 L+
L–
L+16-30 V
0 V L–
1514
1514
13
7
yellow
NAMUR Sensor
NAMUR Encoder
DC-3-wire sensor, PNP
DC-3-wire sensor, NPN
DC-2-wire sensor, PNP
DC-2-wire sensor, NPN
Encoder, push-pull
Encoder, push-pull
Power supply 24 V DC
Power supply 230 V AC
Power supply 115 V AC
Not connected
Sensor power supply GND
Sensor power supply GND
Sensor power supply 24 V DC
Sensor power supply 24 V DC
Trigger input for start-up bypass
External trigger signal
Bridge fitted: start-up bypass triggered by switching on the power supply
Relay output
External rectangular signal
Galvanically isolated input
9NAMUR L+
NAMUR L-8
73
2
1
15
14
13
6
COM
NC
NO
4L+
5L-
16L1 (230 V)
17L1 (115 V)
18N
12
11
10
Wiring Diagrams
Terminal Connection
• Speed monitoring up to;40;kHz• 1 pre-select value with relay output and
LED indicator• 2-, 3-, 4-wire and NAMUR sensors as
well as rotary encoder connectable• Start-up delay• Menu driven operation via 4 front keys• Period measurement• Output signal can be inverted• Display devices can be set between
0.1 ... 2.5 sec.
Dimensions
Electrical connection
KFU8-DW-1.DSupplyRated voltage 196 ... 264 V AC ; 98 ... 132 V AC; 47 ... 63 Hz
20.4 ... 28 V DCPower consumption AC: < 5 VA
DC: < 5 WIndicators/operating meansType 4-digit 7-segment display, red, 7 mm digit heightDisplay interval 0.002 ... 9999 Hz or
0,01 ... 9999 min-1
Parameter assignment keypad-driven menuSwitching state LED yellow, 3 mmInput 1Connectable sensor types NAMUR sensors according to DIN EN 60947-5-6Open loop voltage 8.2 V DCShort-circuit current 6.5 mASwitching point 1.2 ... 2.1 mA Switching hysteresis approx. 0.2 mAInput 2Connectable sensor types Two, three, or four-wire proximity switch, incremental rotary encoder, or externally
generated pulses 16 ... 30 VSensor supply 19 ... 28 V DC non-stabilised; ≤ 30 mA short-circuit proofSwitching point high: 16 ... 30 V DC; max.10 mA due to integrated constant current sink; Ri ≅ 3 kΩ
low: 0 ... 6 V DCInput frequency 0.002 ... 40000 Hz, pulse length/duration: ≥ 12µsInput 3Start-up override Triggering by external signal 16 ... 30 V or Place jumper between terminals 2/3 or
by switching on supply voltage (terminal 2 and terminal 3 permanently bridged)Jumpering time 0.1 ... 999.9 s (External trigger signal)OutputRelay 1 changeover contact
NO, NC, COMSensor supply 24 V DC ± 10 %, 30 mA , short-circuit proofContact loading 250 V AC/2 A/ cos φ ≥ 0.7
40 V DC/2 ATransfer characteristicsMeasuring error 0 ... 40000 Hz: ≤ ±0,10%
Display: ±1 digitTimer function Rise/fall delay, wipe contact, pulse extensionTime 0 ... 999.9 s ; Direction of action reversibleAmbient conditionsAmbient temperature -25 ... 60 °C (248 ... 333 K)Mechanical specificationsProtection degree IP20Connection coded, removable terminals , max. core cross-section 0.34 ... 2.5 mm2
Mode
Output Drehzahlwächter Speed monitor
Enter
+
–
1 2 3 4 5 6
13 14 15 16 17 187 8 9 10 11 12
PEPPERL+FUCHS GERMANY
Control keys
7-segment-display
Yellow LED, Relay switch state indication
107
93
115
L+
L–89
L+
L–
151413
7
L+
L–89
L+
L– 13
71514
L+
L–
151413
7 L+
L– 13
71514
L+
L–
151413
7 L+
L–
L+16-30 V
0 V L–
1514
1514
13
7
yellow
NAMUR Sensor
NAMUR Encoder
DC-3-wire sensor, PNP
DC-3-wire sensor, NPN
DC-2-wire sensor, PNP
DC-2-wire sensor, NPN
Encoder, push-pull
Encoder, push-pull
Power supply 24 V DC
Power supply 230 V AC
Power supply 115 V AC
Not connected
Sensor power supply GND
Sensor power supply GND
Sensor power supply 24 V DC
Sensor power supply 24 V DC
Trigger input for start-up bypass
External trigger signal
Bridge fitted: start-up bypass triggered by switching on the power supply
Relay output
External rectangular signal
Galvanically isolated input
9NAMUR L+
NAMUR L-8
73
2
1
15
14
13
6
COM
NC
NO
4L+
5L-
16L1 (230 V)
17L1 (115 V)
18N
12
11
10
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
1100 Singapore: +65 6779 [email protected]
USA: +1 330 486 [email protected]
Germany: +49 621 [email protected]
Pepperl+Fuchs Groupwww.pepperl-fuchs.com
Subject to modifications without notice Copyright Pepperl+Fuchs
Special Functions Devices
Spec
ial F
unct
ions
Dev
ices
Frequency to Voltage/Curent
• Limit frequency 40 kHz• Voltage or current ouptput• Incrementing output
(Spacing factor 1 ... 9999)• Multi-range power pack• 2-, 3-, 4-wire and NAMUR sensors as
well as rotary encoder connectable• Auxiliary power output for sensors• Connection via Power Rail• Period measurement• Display: Input in Hz or 1/min, output in V
or mA• adjustable updating of indication
(0,001 ... 2,5 s)
Dimensions
Electrical connection
KFU8-FSSP-1.DSupplyRated voltage 196 ... 264 V AC ; 98 ... 132 V AC; 47 ... 63 Hz
20.4 ... 27.6 V DCPower consumption AC: < 5 VA
DC: < 5 WIndicators/operating meansType 4-digit 7-segment display, red, 7 mm digit heightDisplay interval 0.002 ... 9999 Hz or
0,01 ... 9999 min-1
Parameter assignment keypad-driven menuInput 1Connectable sensor types NAMUR sensors according to DIN EN 60947-5-6Open loop voltage 8.2 V DCShort-circuit current 6.5 mASwitching point 1.2 ... 2.1 mA Switching hysteresis approx. 0.2 mAInput 2Connectable sensor types 2-, 3- or 4-wire proximity switches and incremental rotary encoderSensor supply 19 ... 28 V DC non-stabilised; ≤ 30 mA short-circuit proofSwitching point high: 16 ... 30 V DC; max.10 mA; Ri ≅ 3 kOhm
low: 0 ... 6 V DCOutputAnalogue voltage output 0 ... 10 V DC; 2 ... 10 V DC; 30 mA max.; resolution: 12 mV; Ri ≥ 330 Ω (terminal
5+, 6-)Analogue current output 0 ... 20 mA; 4 ... 20 mA; resolution: 25 µA; Ri ≤ 600 Ω (terminal 4-, 5+)Digital incrementing ≥ (Ub -3 V), 20 mA, short-circuit proof (Terminals 1-, 2+)
with frequency division Fin /1 ... Fin /9999Transfer characteristicsInput frequency ≤ 40000 Hz, pulse pause/pulse length: ≥ 12 µsAmbient conditionsAmbient temperature -25 ... 60 °C (248 ... 333 K)Mechanical specificationsProtection degree IP20Connection coded, removable terminals , max. core cross-section 0.34 ... 2.5 mm2
Mode
Output Drehzahlwächter Speed monitor
Enter
+
–
1 2 3 4 5 6
13 14 15 16 17 187 8 9 10 11 12
PEPPERL+FUCHS GERMANY
Control keys
7-segment-display
107
93
115
NAMUR L+
NAMUR L–
L+
L–
L+
L–
L+
L–
L+
L–
L+
L–
L+
L–
L+
L–
N
L1 (230 V)
L1 (115 V)
9
8
7
15
14
13
11
12
16
18
17
DC
DC
D
A
5I+ / U+
I–
U–
4
6
2
1
3
10
V
mA
Ri ≤ 600 Ω
13, 14157
13147, 15
13, 14157
1314
8
9
8
9
7, 15Ri ≥ 330 Ω
Power supply 115 V AC
Power supply 24 V DC
Sensor power supply 24 V
Power supply 230 V AC
Encoder, push-pull
Encoder, push-pull
DC-3-wire sensor, PNP
DC-3-wire sensor, NPN
NAMUR Sensor
NAMUR Encoder
Galvanically isolated input for PNP- and NPN- output circuits
Sensor power supply GND
Sensor power supply GND
Pulse output
Not connected
Not connected
Technical Specifications
• Limit frequency 40 kHz• Voltage or current ouptput• Multi-range power pack• 2-, 3-, 4-wire and NAMUR sensors as
well as rotary encoder connectable• Auxiliary power output for sensors• Connection via Power Rail• Period measurement• Display: Input in Hz or 1/min,
output in V or mA• Adjustable updating of indication
(0,001...2,5 s)
• Limit frequency 40 kHz• Voltage or current ouptput• Incrementing output
(Spacing factor 1 ... 9999)• Multi-range power pack• 2-, 3-, 4-wire and NAMUR sensors as
well as rotary encoder connectable• Auxiliary power output for sensors• Connection via Power Rail• Period measurement• Display: Input in Hz or 1/min, output in V
or mA• adjustable updating of indication
(0,001 ... 2,5 s)
Dimensions
Electrical connection
KFU8-FSSP-1.DSupplyRated voltage 196 ... 264 V AC ; 98 ... 132 V AC; 47 ... 63 Hz
20.4 ... 27.6 V DCPower consumption AC: < 5 VA
DC: < 5 WIndicators/operating meansType 4-digit 7-segment display, red, 7 mm digit heightDisplay interval 0.002 ... 9999 Hz or
0,01 ... 9999 min-1
Parameter assignment keypad-driven menuInput 1Connectable sensor types NAMUR sensors according to DIN EN 60947-5-6Open loop voltage 8.2 V DCShort-circuit current 6.5 mASwitching point 1.2 ... 2.1 mA Switching hysteresis approx. 0.2 mAInput 2Connectable sensor types 2-, 3- or 4-wire proximity switches and incremental rotary encoderSensor supply 19 ... 28 V DC non-stabilised; ≤ 30 mA short-circuit proofSwitching point high: 16 ... 30 V DC; max.10 mA; Ri ≅ 3 kOhm
low: 0 ... 6 V DCOutputAnalogue voltage output 0 ... 10 V DC; 2 ... 10 V DC; 30 mA max.; resolution: 12 mV; Ri ≥ 330 Ω (terminal
5+, 6-)Analogue current output 0 ... 20 mA; 4 ... 20 mA; resolution: 25 µA; Ri ≤ 600 Ω (terminal 4-, 5+)Digital incrementing ≥ (Ub -3 V), 20 mA, short-circuit proof (Terminals 1-, 2+)
with frequency division Fin /1 ... Fin /9999Transfer characteristicsInput frequency ≤ 40000 Hz, pulse pause/pulse length: ≥ 12 µsAmbient conditionsAmbient temperature -25 ... 60 °C (248 ... 333 K)Mechanical specificationsProtection degree IP20Connection coded, removable terminals , max. core cross-section 0.34 ... 2.5 mm2
Mode
Output Drehzahlwächter Speed monitor
Enter
+
–
1 2 3 4 5 6
13 14 15 16 17 187 8 9 10 11 12
PEPPERL+FUCHS GERMANY
Control keys
7-segment-display
107
93
115
NAMUR L+
NAMUR L–
L+
L–
L+
L–
L+
L–
L+
L–
L+
L–
L+
L–
L+
L–
N
L1 (230 V)
L1 (115 V)
9
8
7
15
14
13
11
12
16
18
17
DC
DC
D
A
5I+ / U+
I–
U–
4
6
2
1
3
10
V
mA
Ri ≤ 600 Ω
13, 14157
13147, 15
13, 14157
1314
8
9
8
9
7, 15Ri ≥ 330 Ω
Power supply 115 V AC
Power supply 24 V DC
Sensor power supply 24 V
Power supply 230 V AC
Encoder, push-pull
Encoder, push-pull
DC-3-wire sensor, PNP
DC-3-wire sensor, NPN
NAMUR Sensor
NAMUR Encoder
Galvanically isolated input for PNP- and NPN- output circuits
Sensor power supply GND
Sensor power supply GND
Pulse output
Not connected
Not connected
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
1101Singapore: +65 6779 [email protected]
USA: +1 330 486 [email protected]
Germany: +49 621 [email protected]
Pepperl+Fuchs Groupwww.pepperl-fuchs.com
Subject to modifications without notice Copyright Pepperl+Fuchs
Special Functions Devices
Special Functions Devices
Wiring Diagrams
Terminal Connection
Dimensions
• Limit frequency 40 kHz• Voltage or current ouptput• Incrementing output
(Spacing factor 1 ... 9999)• Multi-range power pack• 2-, 3-, 4-wire and NAMUR sensors as
well as rotary encoder connectable• Auxiliary power output for sensors• Connection via Power Rail• Period measurement• Display: Input in Hz or 1/min, output in V
or mA• adjustable updating of indication
(0,001 ... 2,5 s)
Dimensions
Electrical connection
KFU8-FSSP-1.DSupplyRated voltage 196 ... 264 V AC ; 98 ... 132 V AC; 47 ... 63 Hz
20.4 ... 27.6 V DCPower consumption AC: < 5 VA
DC: < 5 WIndicators/operating meansType 4-digit 7-segment display, red, 7 mm digit heightDisplay interval 0.002 ... 9999 Hz or
0,01 ... 9999 min-1
Parameter assignment keypad-driven menuInput 1Connectable sensor types NAMUR sensors according to DIN EN 60947-5-6Open loop voltage 8.2 V DCShort-circuit current 6.5 mASwitching point 1.2 ... 2.1 mA Switching hysteresis approx. 0.2 mAInput 2Connectable sensor types 2-, 3- or 4-wire proximity switches and incremental rotary encoderSensor supply 19 ... 28 V DC non-stabilised; ≤ 30 mA short-circuit proofSwitching point high: 16 ... 30 V DC; max.10 mA; Ri ≅ 3 kOhm
low: 0 ... 6 V DCOutputAnalogue voltage output 0 ... 10 V DC; 2 ... 10 V DC; 30 mA max.; resolution: 12 mV; Ri ≥ 330 Ω (terminal
5+, 6-)Analogue current output 0 ... 20 mA; 4 ... 20 mA; resolution: 25 µA; Ri ≤ 600 Ω (terminal 4-, 5+)Digital incrementing ≥ (Ub -3 V), 20 mA, short-circuit proof (Terminals 1-, 2+)
with frequency division Fin /1 ... Fin /9999Transfer characteristicsInput frequency ≤ 40000 Hz, pulse pause/pulse length: ≥ 12 µsAmbient conditionsAmbient temperature -25 ... 60 °C (248 ... 333 K)Mechanical specificationsProtection degree IP20Connection coded, removable terminals , max. core cross-section 0.34 ... 2.5 mm2
Mode
Output Drehzahlwächter Speed monitor
Enter
+
–
1 2 3 4 5 6
13 14 15 16 17 187 8 9 10 11 12
PEPPERL+FUCHS GERMANY
Control keys
7-segment-display
107
93
115
NAMUR L+
NAMUR L–
L+
L–
L+
L–
L+
L–
L+
L–
L+
L–
L+
L–
L+
L–
N
L1 (230 V)
L1 (115 V)
9
8
7
15
14
13
11
12
16
18
17
DC
DC
D
A
5I+ / U+
I–
U–
4
6
2
1
3
10
V
mA
Ri ≤ 600 Ω
13, 14157
13147, 15
13, 14157
1314
8
9
8
9
7, 15Ri ≥ 330 Ω
Power supply 115 V AC
Power supply 24 V DC
Sensor power supply 24 V
Power supply 230 V AC
Encoder, push-pull
Encoder, push-pull
DC-3-wire sensor, PNP
DC-3-wire sensor, NPN
NAMUR Sensor
NAMUR Encoder
Galvanically isolated input for PNP- and NPN- output circuits
Sensor power supply GND
Sensor power supply GND
Pulse output
Not connected
Not connected
• Limit frequency 40 kHz• Voltage or current ouptput• Incrementing output
(Spacing factor 1 ... 9999)• Multi-range power pack• 2-, 3-, 4-wire and NAMUR sensors as
well as rotary encoder connectable• Auxiliary power output for sensors• Connection via Power Rail• Period measurement• Display: Input in Hz or 1/min, output in V
or mA• adjustable updating of indication
(0,001 ... 2,5 s)
Dimensions
Electrical connection
KFU8-FSSP-1.DSupplyRated voltage 196 ... 264 V AC ; 98 ... 132 V AC; 47 ... 63 Hz
20.4 ... 27.6 V DCPower consumption AC: < 5 VA
DC: < 5 WIndicators/operating meansType 4-digit 7-segment display, red, 7 mm digit heightDisplay interval 0.002 ... 9999 Hz or
0,01 ... 9999 min-1
Parameter assignment keypad-driven menuInput 1Connectable sensor types NAMUR sensors according to DIN EN 60947-5-6Open loop voltage 8.2 V DCShort-circuit current 6.5 mASwitching point 1.2 ... 2.1 mA Switching hysteresis approx. 0.2 mAInput 2Connectable sensor types 2-, 3- or 4-wire proximity switches and incremental rotary encoderSensor supply 19 ... 28 V DC non-stabilised; ≤ 30 mA short-circuit proofSwitching point high: 16 ... 30 V DC; max.10 mA; Ri ≅ 3 kOhm
low: 0 ... 6 V DCOutputAnalogue voltage output 0 ... 10 V DC; 2 ... 10 V DC; 30 mA max.; resolution: 12 mV; Ri ≥ 330 Ω (terminal
5+, 6-)Analogue current output 0 ... 20 mA; 4 ... 20 mA; resolution: 25 µA; Ri ≤ 600 Ω (terminal 4-, 5+)Digital incrementing ≥ (Ub -3 V), 20 mA, short-circuit proof (Terminals 1-, 2+)
with frequency division Fin /1 ... Fin /9999Transfer characteristicsInput frequency ≤ 40000 Hz, pulse pause/pulse length: ≥ 12 µsAmbient conditionsAmbient temperature -25 ... 60 °C (248 ... 333 K)Mechanical specificationsProtection degree IP20Connection coded, removable terminals , max. core cross-section 0.34 ... 2.5 mm2
Mode
Output Drehzahlwächter Speed monitor
Enter
+
–
1 2 3 4 5 6
13 14 15 16 17 187 8 9 10 11 12
PEPPERL+FUCHS GERMANY
Control keys
7-segment-display
107
93
115
NAMUR L+
NAMUR L–
L+
L–
L+
L–
L+
L–
L+
L–
L+
L–
L+
L–
L+
L–
N
L1 (230 V)
L1 (115 V)
9
8
7
15
14
13
11
12
16
18
17
DC
DC
D
A
5I+ / U+
I–
U–
4
6
2
1
3
10
V
mA
Ri ≤ 600 Ω
13, 14157
13147, 15
13, 14157
1314
8
9
8
9
7, 15Ri ≥ 330 Ω
Power supply 115 V AC
Power supply 24 V DC
Sensor power supply 24 V
Power supply 230 V AC
Encoder, push-pull
Encoder, push-pull
DC-3-wire sensor, PNP
DC-3-wire sensor, NPN
NAMUR Sensor
NAMUR Encoder
Galvanically isolated input for PNP- and NPN- output circuits
Sensor power supply GND
Sensor power supply GND
Pulse output
Not connected
Not connected
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
1102 Singapore: +65 6779 [email protected]
USA: +1 330 486 [email protected]
Germany: +49 621 [email protected]
Pepperl+Fuchs Groupwww.pepperl-fuchs.com
Subject to modifications without notice Copyright Pepperl+Fuchs
Special Functions Devices
Spec
ial F
unct
ions
Dev
ices
• 1-channel standstill controller• Rotation direction detection or start-up
override selectable• 2 relay outputs• Input frequency ≤ 2 kHz• Diagnosis LEDs for rotation detection,
signal below the trip value, operating voltage and hardware error
• Simple setting of function and limiting frequency via DIP switch on the front side
• Plug-in terminals
7 8 9
10 11 12
1 2 34 5 6
13 14 15
1
2
S1S2S3
PWRCHKOUT
12
3
III
Front view
Switch S1:Cutoff frequency
Switch S2:Cutoff frequency
LED green:Power supply
Removable terminalsgreen
LED yellow:Relay output I
LED yellow:Relay output II
Switch S3:Start-up override/Rotation direction detectionLEDs flashing red:
Hardware error
Removable terminalsgreen
Electrical connection
KFD2-SR2-2.W.SMGeneral specificationsPre-selection singleProgramming via DIP switch and programmableSupplyRated voltage 20 ... 30 V DCPower consumption ≤ 1.5 WIndicators/operating meansLED green Operating voltageLED yellow switching stateLED red Hardware errorDIP-switch setting the configurationInputRated values acc. to EN 60947-5-6 (NAMUR)Switching point/Switching hyste-resis
x ≤ 1,2 mA oder x ≥ 2,1 mA / approx. 0.9 mA
Control input sensor power supply approx. 8.2 V, impedance 1.2 kΩLead monitoring not availablePulse duration > 200 µs for standstill monitoring,
> 250 µs for rotation direction detecionOutputRelay 2 changeover contactsContact loading 253 V AC/2 A /cos φ > 0.7; 40 V DC/2 A resistive load;Energized/de-energized delay approx. 20 ms / approx. 20 msMechanical life 5 x 106 switching cyclesTrip value for standstill monitoring:
0.1 Hz; 0.5 Hz; 2 Hz; 10 Hzadjustable via DIP switch (S1 and S2)
Transfer characteristicsAccuracy ± 5 %Start-up override 5 seconds or 20 seconds, programmableFrequency range ≤ 2 kHzRotation direction detection 90° phase difference between pulse input signal 1 and 2, overlapping ≥ 125 µsElectrical isolationInput/output safe electrical isolation per EN 50178, voltage peak value 253 VInput/power supply safe electrical isolation per EN 50178, voltage peak value 253 VOutput/power supply safe electrical isolation per EN 50178, voltage peak value 253 VOutput/output basic insulation according to DIN EN 50178, rated insulation voltage 253 VeffAmbient conditionsAmbient temperature -20 ... 60 °C (253 ... 333 K)Mechanical specificationsProtection degree IP20Connection plug-in terminalsMass approx. 150 gDimensions 20 mm x 118 mm x 115 mm
Input I Input II
green
Output I Output II Power supply
yellow yellow
red
external supply
3-wirepnp/push-pull
external supply
3-wirepnp/push-pull
Start-up override
20 sec.
5 sec.Jumper (switch-on trigger)or trigger signal
Contact(not bouncing)
Contact(not bouncing)
+ -
1+ 3-
+ 24 V- 24 V
3-2+
-+Q
1+ 3-
2+
3-1+
+ 24 V- 24 V
6-
-+Q
4+ 6-
6-4+
6-4+
6-5+
4+ 6-5+
14 157 8 9 10 11 12
NAMUR NAMUR
S1 S2 S3
Zero Speed Monitor
Technical Specifications
• 1-channel standstill controller• Rotation direction detection or
start-up override selectable• 2 relay outputs• Input frequency ≤ 2 kHz• Diagnosis LEDs for rotation detection,
signal below the trip value, operating voltage and hardware error
• Simple setting of function and limiting frequency via DIP switch on the front side
• Plug-in terminals• 1-channel standstill controller• Rotation direction detection or start-up
override selectable• 2 relay outputs• Input frequency ≤ 2 kHz• Diagnosis LEDs for rotation detection,
signal below the trip value, operating voltage and hardware error
• Simple setting of function and limiting frequency via DIP switch on the front side
• Plug-in terminals
7 8 9
10 11 12
1 2 34 5 6
13 14 15
1
2
S1S2S3
PWRCHKOUT
12
3
III
Front view
Switch S1:Cutoff frequency
Switch S2:Cutoff frequency
LED green:Power supply
Removable terminalsgreen
LED yellow:Relay output I
LED yellow:Relay output II
Switch S3:Start-up override/Rotation direction detectionLEDs flashing red:
Hardware error
Removable terminalsgreen
Electrical connection
KFD2-SR2-2.W.SMGeneral specificationsPre-selection singleProgramming via DIP switch and programmableSupplyRated voltage 20 ... 30 V DCPower consumption ≤ 1.5 WIndicators/operating meansLED green Operating voltageLED yellow switching stateLED red Hardware errorDIP-switch setting the configurationInputRated values acc. to EN 60947-5-6 (NAMUR)Switching point/Switching hyste-resis
x ≤ 1,2 mA oder x ≥ 2,1 mA / approx. 0.9 mA
Control input sensor power supply approx. 8.2 V, impedance 1.2 kΩLead monitoring not availablePulse duration > 200 µs for standstill monitoring,
> 250 µs for rotation direction detecionOutputRelay 2 changeover contactsContact loading 253 V AC/2 A /cos φ > 0.7; 40 V DC/2 A resistive load;Energized/de-energized delay approx. 20 ms / approx. 20 msMechanical life 5 x 106 switching cyclesTrip value for standstill monitoring:
0.1 Hz; 0.5 Hz; 2 Hz; 10 Hzadjustable via DIP switch (S1 and S2)
Transfer characteristicsAccuracy ± 5 %Start-up override 5 seconds or 20 seconds, programmableFrequency range ≤ 2 kHzRotation direction detection 90° phase difference between pulse input signal 1 and 2, overlapping ≥ 125 µsElectrical isolationInput/output safe electrical isolation per EN 50178, voltage peak value 253 VInput/power supply safe electrical isolation per EN 50178, voltage peak value 253 VOutput/power supply safe electrical isolation per EN 50178, voltage peak value 253 VOutput/output basic insulation according to DIN EN 50178, rated insulation voltage 253 VeffAmbient conditionsAmbient temperature -20 ... 60 °C (253 ... 333 K)Mechanical specificationsProtection degree IP20Connection plug-in terminalsMass approx. 150 gDimensions 20 mm x 118 mm x 115 mm
Input I Input II
green
Output I Output II Power supply
yellow yellow
red
external supply
3-wirepnp/push-pull
external supply
3-wirepnp/push-pull
Start-up override
20 sec.
5 sec.Jumper (switch-on trigger)or trigger signal
Contact(not bouncing)
Contact(not bouncing)
+ -
1+ 3-
+ 24 V- 24 V
3-2+
-+Q
1+ 3-
2+
3-1+
+ 24 V- 24 V
6-
-+Q
4+ 6-
6-4+
6-4+
6-5+
4+ 6-5+
14 157 8 9 10 11 12
NAMUR NAMUR
S1 S2 S3
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
1103Singapore: +65 6779 [email protected]
USA: +1 330 486 [email protected]
Germany: +49 621 [email protected]
Pepperl+Fuchs Groupwww.pepperl-fuchs.com
Subject to modifications without notice Copyright Pepperl+Fuchs
Special Functions Devices
Special Functions Devices
• 1-channel standstill controller• Rotation direction detection or start-up
override selectable• 2 relay outputs• Input frequency ≤ 2 kHz• Diagnosis LEDs for rotation detection,
signal below the trip value, operating voltage and hardware error
• Simple setting of function and limiting frequency via DIP switch on the front side
• Plug-in terminals
7 8 9
10 11 12
1 2 34 5 6
13 14 15
1
2
S1S2S3
PWRCHKOUT
12
3
III
Front view
Switch S1:Cutoff frequency
Switch S2:Cutoff frequency
LED green:Power supply
Removable terminalsgreen
LED yellow:Relay output I
LED yellow:Relay output II
Switch S3:Start-up override/Rotation direction detectionLEDs flashing red:
Hardware error
Removable terminalsgreen
Electrical connection
KFD2-SR2-2.W.SMGeneral specificationsPre-selection singleProgramming via DIP switch and programmableSupplyRated voltage 20 ... 30 V DCPower consumption ≤ 1.5 WIndicators/operating meansLED green Operating voltageLED yellow switching stateLED red Hardware errorDIP-switch setting the configurationInputRated values acc. to EN 60947-5-6 (NAMUR)Switching point/Switching hyste-resis
x ≤ 1,2 mA oder x ≥ 2,1 mA / approx. 0.9 mA
Control input sensor power supply approx. 8.2 V, impedance 1.2 kΩLead monitoring not availablePulse duration > 200 µs for standstill monitoring,
> 250 µs for rotation direction detecionOutputRelay 2 changeover contactsContact loading 253 V AC/2 A /cos φ > 0.7; 40 V DC/2 A resistive load;Energized/de-energized delay approx. 20 ms / approx. 20 msMechanical life 5 x 106 switching cyclesTrip value for standstill monitoring:
0.1 Hz; 0.5 Hz; 2 Hz; 10 Hzadjustable via DIP switch (S1 and S2)
Transfer characteristicsAccuracy ± 5 %Start-up override 5 seconds or 20 seconds, programmableFrequency range ≤ 2 kHzRotation direction detection 90° phase difference between pulse input signal 1 and 2, overlapping ≥ 125 µsElectrical isolationInput/output safe electrical isolation per EN 50178, voltage peak value 253 VInput/power supply safe electrical isolation per EN 50178, voltage peak value 253 VOutput/power supply safe electrical isolation per EN 50178, voltage peak value 253 VOutput/output basic insulation according to DIN EN 50178, rated insulation voltage 253 VeffAmbient conditionsAmbient temperature -20 ... 60 °C (253 ... 333 K)Mechanical specificationsProtection degree IP20Connection plug-in terminalsMass approx. 150 gDimensions 20 mm x 118 mm x 115 mm
Input I Input II
green
Output I Output II Power supply
yellow yellow
red
external supply
3-wirepnp/push-pull
external supply
3-wirepnp/push-pull
Start-up override
20 sec.
5 sec.Jumper (switch-on trigger)or trigger signal
Contact(not bouncing)
Contact(not bouncing)
+ -
1+ 3-
+ 24 V- 24 V
3-2+
-+Q
1+ 3-
2+
3-1+
+ 24 V- 24 V
6-
-+Q
4+ 6-
6-4+
6-4+
6-5+
4+ 6-5+
14 157 8 9 10 11 12
NAMUR NAMUR
S1 S2 S3
Wiring Diagrams
Terminal Connection
Dimensions
• 1-channel standstill controller• Rotation direction detection or start-up
override selectable• 2 relay outputs• Input frequency ≤ 2 kHz• Diagnosis LEDs for rotation detection,
signal below the trip value, operating voltage and hardware error
• Simple setting of function and limiting frequency via DIP switch on the front side
• Plug-in terminals
7 8 9
10 11 12
1 2 34 5 6
13 14 15
1
2
S1S2S3
PWRCHKOUT
12
3
III
Front view
Switch S1:Cutoff frequency
Switch S2:Cutoff frequency
LED green:Power supply
Removable terminalsgreen
LED yellow:Relay output I
LED yellow:Relay output II
Switch S3:Start-up override/Rotation direction detectionLEDs flashing red:
Hardware error
Removable terminalsgreen
Electrical connection
KFD2-SR2-2.W.SMGeneral specificationsPre-selection singleProgramming via DIP switch and programmableSupplyRated voltage 20 ... 30 V DCPower consumption ≤ 1.5 WIndicators/operating meansLED green Operating voltageLED yellow switching stateLED red Hardware errorDIP-switch setting the configurationInputRated values acc. to EN 60947-5-6 (NAMUR)Switching point/Switching hyste-resis
x ≤ 1,2 mA oder x ≥ 2,1 mA / approx. 0.9 mA
Control input sensor power supply approx. 8.2 V, impedance 1.2 kΩLead monitoring not availablePulse duration > 200 µs for standstill monitoring,
> 250 µs for rotation direction detecionOutputRelay 2 changeover contactsContact loading 253 V AC/2 A /cos φ > 0.7; 40 V DC/2 A resistive load;Energized/de-energized delay approx. 20 ms / approx. 20 msMechanical life 5 x 106 switching cyclesTrip value for standstill monitoring:
0.1 Hz; 0.5 Hz; 2 Hz; 10 Hzadjustable via DIP switch (S1 and S2)
Transfer characteristicsAccuracy ± 5 %Start-up override 5 seconds or 20 seconds, programmableFrequency range ≤ 2 kHzRotation direction detection 90° phase difference between pulse input signal 1 and 2, overlapping ≥ 125 µsElectrical isolationInput/output safe electrical isolation per EN 50178, voltage peak value 253 VInput/power supply safe electrical isolation per EN 50178, voltage peak value 253 VOutput/power supply safe electrical isolation per EN 50178, voltage peak value 253 VOutput/output basic insulation according to DIN EN 50178, rated insulation voltage 253 VeffAmbient conditionsAmbient temperature -20 ... 60 °C (253 ... 333 K)Mechanical specificationsProtection degree IP20Connection plug-in terminalsMass approx. 150 gDimensions 20 mm x 118 mm x 115 mm
Input I Input II
green
Output I Output II Power supply
yellow yellow
red
external supply
3-wirepnp/push-pull
external supply
3-wirepnp/push-pull
Start-up override
20 sec.
5 sec.Jumper (switch-on trigger)or trigger signal
Contact(not bouncing)
Contact(not bouncing)
+ -
1+ 3-
+ 24 V- 24 V
3-2+
-+Q
1+ 3-
2+
3-1+
+ 24 V- 24 V
6-
-+Q
4+ 6-
6-4+
6-4+
6-5+
4+ 6-5+
14 157 8 9 10 11 12
NAMUR NAMUR
S1 S2 S3
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
1104 Singapore: +65 6779 [email protected]
USA: +1 330 486 [email protected]
Germany: +49 621 [email protected]
Pepperl+Fuchs Groupwww.pepperl-fuchs.com
Subject to modifications without notice Copyright Pepperl+Fuchs
Special Functions Devices
Spec
ial F
unct
ions
Dev
ices
Notes
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com