Upload
volien
View
216
Download
0
Embed Size (px)
Citation preview
AMPLIFIER
INTRODUCTIONThis instruction manual is for your safety and must be adhered to at all times. Please read and ensure that you fully understand the installation and set up procedures as explained. If you are unclear on the installation or set up of your EDGE speakers please contact your nearest authorised EDGE dealer.
WARNINGDO NOT EXPOSE THIS PRODUCT TO DAMP OR MOISTURE - doing so may result in fire,
shock or damage to the product.BEFORE WIRING DISCONNECT THE CABLE FROM THE POSITIVE BATTERY TERMINAL -
failure to do so may result in electric shock or injury.ENSURE GOOD AND CORRECT CONNECTIONS - failure to make the correct connections
may result in fire or damage to the product.DO NOT USE ANY FUNCTIONS OF THIS EQUIPMENT THAT MAY TAKE YOUR
CONCENTRATION AWAY FROM DRIVING YOUR VEHICLE - do not set up your amplifier whilst driving, doing so may result in an accident. For prolonged setting up, make sure that
your vehicle is stationary and in a safe location.KEEP THE VOLUME AT A LEVEL SO YOU CAN STILL HEAR OUTSIDE NOISE - failure to do this may result in an accident. EDGE equipment is capable of producing sound levels that can permanently damage your hearing. EDGE recommends caution when listening at high volume. For safe and enjoyable listening the sound should be comfortable and clear without distortion.
CAUTIONNever connect any speaker lead to the car chassis. This can cause severe damage to your
speaker /car radio /amplifier.Before drilling or cutting any holes, investigate the layout of your vehicle thoroughly.
Use caution when working near the fuel / hydraulic lines and electrical wiring.Observe the correct polarity when wiring, improper phasing may cause a loss of bass
response.Ensure that no moving parts catch on the speaker or grill (e.g. window or door handles, or
window glass inside the door)
Mounting Guidelines
Your EDGE amplifier is designed with a swift installation routine in mind. Please mount the amplifier in a dry location on a solid surface. NEVER mount the amplifier upside down, this will cause the amplifier to over heat and will eventually damage the amplifier. Before fixing the amplifier in place please ensure that there is sufficient air flow around the exterior of the casing, at least two inches is sufficient.
Connections
Power / Ground Cable● The correct gauge cable should be used for both the power and the ground connections to the amplifier. ● The power cable should be taken directly from the battery. Rubber grommets should be used when passing through any bulkheads to prevent the cable from becoming chaffed or cut. ● The correct size of fuse must be fitted within 18” of the battery and before the cable passes through the bulk head● It is vital that a fuse / circuit breaker (of at least equal value to the one fitted on the amplifier) is placed inline with the power cable and is no further than eighteen inches away from the battery. ● Please ensure that the fuse is not fitted until the entire installation procedure is complete. ● The two tables below are to help you decide on what cable is correct for you. The first enables you to select the size of cable depending on the length required. The second will help you convert the cable size from American Wire Gauge to Metric if you need to.● The amplifier ground should be connected directly to the chassis of the vehicle, to bare metal. ● The cable length should be kept to an absolute minimum.
Mo
de
l E
D2
04
E
D2
05
E
D2
06
E
D2
09
Ty
pe
Coa
xial
C
oaxi
al
Coa
xial
C
oaxi
al
Con
figur
atio
n 4
way
4
way
4
way
4
way
Spea
ker s
ize
4” (1
00m
m)
5.25
” (13
0mm
) 6.
5” (1
65m
m)
6x9”
(150
x 2
20m
m)
R
MS
pow
er
40 w
atts
50
wat
ts
60 w
atts
10
0 w
atts
Pe
ak p
ower
12
0 w
atts
15
0 w
atts
18
0 w
atts
30
0 w
atts
M
inim
um in
put
20 w
RM
S 25
wR
MS
30 w
RM
S 50
wR
MS
Sens
itivi
ty
83.9
dB
86.2
dB
86.2
dB
86.1
dB
Freq
uenc
y re
spon
se 1
00H
z –
20KH
z 80
Hz
– 20
KHz
65hz
– 2
0KH
z 45
Hz-
20K
Hz
Mou
ntin
g de
pth
43m
m
47m
m
55m
m
72m
m
Mou
ntin
g di
amet
er
94m
m
118m
m
144m
m
150x
220m
mR
ecom
men
ded
ED74
00/7
800
ED74
00/7
800
ED74
00/7
800
ED74
00/7
800
ampl
ifier
ED
7160
0 ED
7160
0 ED
7160
0
ED
7160
0
Mo
de
l E
D3
05
E
D3
06
Type
co
mpo
nent
co
mpo
nent
C
onfig
urat
ion
2 w
ay
2 w
ay
Sp
eake
r siz
e 5.
25” (
130m
m)
6.5”
(165
mm
)
R
MS
pow
er
70 w
atts
80
wat
ts
Pe
ak p
ower
21
0 w
atts
24
0 w
atts
M
inim
um in
put
35 w
atts
RM
S 40
wat
ts R
MS
Sens
itivi
ty
82.2
dB
84.4
dB
Fr
eque
ncy
resp
onse
80H
z –
20KH
z
65h
z –
20KH
z
M
ount
ing
dept
h
54m
m
57m
m
Mou
ntin
g di
amet
er
114m
m
144m
mR
ecom
men
ded
ED74
00/7
800
ED74
00/7
800
ampl
ifier
ED
7160
0 ED
7160
0
Mo
de
l E
D7
40
0
ED
78
00
E
D716
00
E
D712
00
E
D7
25
00
Ty
pe
2/1
chan
nel
4/3/
2 ch
anne
l 4/
3/2
chan
nel
Mon
oblo
ck
Mon
oblo
ck
C
lass
AB
AB
AB
D
D
4
ohm
ste
reo
2 x
80 w
atts
RM
S 4
x 80
wat
ts R
MS
4 x
140
wat
ts R
MS
N/A
N
/A
2 oh
m s
tere
o 2
x 10
0 w
atts
RM
S 4
x 10
0 w
atts
RM
S 4
x 20
0 w
atts
RM
S N
/A
N/A
4 oh
m m
ono
1 x
200
wat
ts R
MS
2 x
200
wat
ts R
MS
2 x
400
wat
ts R
MS
1 x
200
wat
ts R
MS
1 x
400
wat
ts R
MS
2 oh
m m
ono
N/A
N
/A
N/A
1
x 40
0 w
atts
RM
S 1
x 80
0 w
atts
RM
S1
ohm
mon
o N
/A
N/A
N
/A
1 x
600
wat
ts R
MS
1
x 12
50 w
atts
RM
SM
ax p
ower
40
0 w
atts
80
0 w
atts
16
00 w
atts
12
00 w
atts
25
00 w
atts
Freq
resp
onse
20
Hz
– 20
KHZ
20H
z –
20KH
z
20H
z –
20KH
z 20
Hz
– 30
0Hz
20 H
z –
300H
zH
eigh
t 66
mm
66
mm
66
mm
66
mm
66
mm
Wid
th
282m
m
332m
m
452m
m
332m
m
416
mm
Dep
th
245m
m
245m
m
245m
m
245m
m
245m
m
Mo
de
l E
D510
E
D512
E
D515
Type
su
bwoo
fer
subw
oofe
r su
bwoo
fer
Spea
ker s
ize
10” (
272m
m)
12” (
324m
m)
15” (
397m
m)
RM
S po
wer
25
0 w
atts
30
0 w
atts
35
0 w
atts
Pe
ak p
ower
75
0 w
atts
90
0 w
atts
10
50 w
atts
M
inim
um in
put
125
wat
ts R
MS
150
wat
ts R
MS
175
wat
ts R
MS
Se
nsiti
vity
89
dB
90dB
90
dB
Fr
eque
ncy
resp
onse
30
Hz
- 170
0Hz
25H
z –
1500
KHz
20hz
– 8
50H
z
Mou
ntin
g di
amet
er
235m
m
285m
m
350m
m
Mou
ntin
g de
pth
125m
m
144m
m
148m
m
Vo
ice
coil
2 oh
m D
VC
2 oh
m D
VC
2 oh
m D
VCR
ecom
men
ded
ED71
200/
7250
0 ED
7120
0/72
500
ED71
200/
7250
0
ampl
ifier
ED74
00/7
800/
7160
0 ED
7400
/780
0/71
600
ED74
00/7
800/
7160
0
Mo
de
l E
DB
10
E
DB
12
E
DB
12
T
EB
615
D
river
ED
510
ED51
2 2
x ED
512
ED51
5
En
clos
ure
impe
danc
e 1
or 4
Ohm
1
or 4
Ohm
1,
4 o
r 8 O
hm
1 or
4 O
hm
R
MS
pow
er
250
wat
ts
300
wat
ts
600
wat
ts
350
wat
ts
Peak
pow
er
750
wat
ts
900
wat
ts
1800
wat
ts
1050
wat
ts
Rec
omm
ende
d
ED
7120
0/72
500/
ED
7120
0/72
500/
ED
7120
0/72
500/
ED
7120
0/72
500/
ampl
ifier
ED
7400
/780
0/71
600
ED74
00/7
800/
7160
0 ED
7400
/780
0/71
600
ED74
00/7
800/
7160
0
Mo
de
l E
D p
ack 1
0
ED
pa
ck 1
2
ED
pa
ck 1
2 t
win
encl
osur
e ED
610
ED61
2 ED
612T
ampl
ifier
ED
7400
ED
7400
ED
7120
0
Spea
ker s
ize
10” (
272m
m)
12” (
324m
m)
15” (
397m
m)
RM
S po
wer
25
0 w
atts
30
0 w
atts
60
0 w
atts
Pe
ak p
ower
75
0 w
atts
90
0 w
atts
18
00 w
atts
Am
plifi
er w
iring
kit
10AW
G in
clud
ed
10AW
G in
clud
ed
8AW
G in
clud
e d
Mo
de
l E
D4
02
E
D4
04
E
D4
05
E
D4
06
E
D4
08
Ty
pe
bulle
t tw
eete
r b
ulle
t tw
eete
r M
idra
nge
Mid
rang
e m
idra
nge
C
onfig
urat
ion
1 w
ay
1 w
ay
1 w
ay
1 w
ay
1 w
ay
Sp
eake
r siz
e 2”
(50m
m)
4” (1
00m
m)
5.25
” (13
0mm
) 6.
5” (1
65m
m)
8” (2
00m
m)
RM
S po
wer
40
wat
ts
50 w
atts
80
wat
ts
300
wat
ts
450
wat
ts
Peak
pow
er
120
wat
ts
150
wat
ts
240
wat
ts
100
wat
ts
150
wat
ts
Min
imum
inpu
t 20
wat
ts R
MS
25 w
atts
RM
S 40
wat
ts R
MS
50 w
atts
RM
S 75
wat
ts R
MS
Se
nsiti
vity
10
6dB
107d
B 96
dB
97dB
98
dB
Freq
uenc
y re
spon
se 5
KHz
– 20
KHz
4.5K
HZ
– 20
KHz
80H
z –
6KH
z 65
hz –
6KH
z 55
Hz
– 6K
Hz
M
ount
ing
diam
eter
43
mm
90
mm
11
4mm
14
6mm
18
3mm
M
ount
ing
dept
h 40
mm
70
mm
49
mm
55
mm
82
mm
R
ecom
men
ded
ED74
00/7
800/
ED
7400
/780
0/
ED74
00/7
800/
ED
7400
/780
0/
ED74
00/7
800/
am
plifi
er
ED71
600
ED71
600
ED71
600
ED71
600
ED71
600
M
od
el
ED
710
E
D712
E
D715
E
D718
Type
w
oofe
r w
oofe
r w
oofe
r w
oofe
r
Sp
eake
r siz
e 10
” (27
2mm
) 12
” (32
4mm
) 15
” (39
7mm
) 18
” (45
7mm
)
RM
S po
wer
40
0 w
atts
50
0 w
atts
60
0 w
atts
90
0 w
atts
Pe
ak p
ower
12
00 w
atts
15
00 w
atts
18
00 w
atts
27
00 w
atts
Min
imum
inpu
t 20
0 w
atts
RM
S 15
0 w
atts
RM
S 30
0 w
atts
RM
S 45
0 w
atts
Sens
itivi
ty
97dB
98
dB
99dB
02
dB
Fr
eque
ncy
resp
onse
30H
z –
5.5K
Hz
25H
z –
5.5K
Hz
20hz
– 5
KHz
15H
z –
5KH
z M
ount
ing
diam
eter
23
4mm
28
4mm
35
2mm
42
8mm
Mou
ntin
g de
pth
113m
m
130m
m
128m
m
186m
m
Vo
ice
coil
2 oh
m D
VC
2 oh
m D
VC
2 oh
m D
VC
2 oh
m D
VCR
ecom
men
ded
ED71
200/
ED72
500
ED71
200/
7250
0 ED
7120
0/72
500
ED71
200/
7250
0
ampl
ifier
ED
7400
/780
0/71
600
ED71
600
ED71
600
ED72
500
Limited WarrantyAll EDGE goods are covered by a full 12 months manufacturers warranty. Valid from the date of the original receipt and proof of purchase. In order to validate this warranty, the warranty card should be returned to EDGE within seven days of the original purchase date. The original receipt and packaging
should also be kept for this 12 month period.
If at any stage during the warranty period you have a problem with the product then it should be returned to the point of purchase in its original packaging,
complete and with no items missing.
If the store is unable to fix the product it may have to be returned to EDGE this process takes around 7
working days.
A full description of EDGE’s warranty information can be found on our website:
www.edgecaraudio.com/warranty
A written version can also be obtained from EDGE warranty department
PO Box 11000B75 7WG
Copyright All content included in this manual such as text, graphics, logos, icons, images data, the selection and arrangement thereof, are the property of EDGE Audio (herein referred
to as “EDGE”, “us” or “we”) and its affiliate or their content and technology providers, and are protected by United Kingdom and International copyright laws. All
rights reserved.
Trademarks EDGE ED2TM, EDGE ED3TM , EDGE ED4TM , EDGE ED5TM
EDGE ED6TM , EDGE ED7TM, EDGE StreetTM and EDGE LoudTM and all stylised representations of
product names, or the abbreviations of product names, as logos are all trademarks of EDGE. Graphics and
logos are trademarks or trade dress of EDGE Audio or its subsidiaries.
EDGE’s trademarks and trade dress may not be used in connection with any product or service that is not EDGE’s,
in any manner that is likely to cause confusion among customers or in any manner that disparages or discredits EDGE. All other trademarks not owned by EDGE or its subsidiaries that appear in this manual are the property
of their respective owners, who may or may not be affiliated with, connected to, or sponsored by EDGE or
its subsidiaries. We reserve the right to make needed changes or
improvements to the produc and this manual , without informing the customer about this in advance
ED7400● Minimum 10 AWG power / ground cable should be used
ED7800 / 71200 / 71600● Minimum 8 AWG power / ground cable should be used
ED72500● Minimum 4 AWG power / ground cable should be used
Remote Turn On
● A minimum of 18 gauge cable should be used for this connection. ● The cable should be run with exactly the same care and attention as the power cable and taken back to the source (headunit) and joined to the remote cable provided. ● If the source (headunit) does not have a remote turn on cable then a 12v supply should be used. This will require a switch to be fitted inline to enable the amplifier to be turned on and off. Remember that if this switch is left on you will flatten the car battery.
RCA Cables
● Depending on the model number of your amplifier and the number of speakers you wish to power you will have to run either one or two RCA cables from the source to the amplifier. ● Please take extra care when running these cables from the source to the amplifier. Ensure that they are placed away from all items that can generate any interference, wiring harnesses etc. ● It is recommended that the RCA cables should be run on opposite sides of the car to the previously installed power cables if possible, to avoid the cable picking up interference.
Terminals and Controls ED7400
5. Low Pass Crossover ControlThe control is used to select the low pass filter frequency. The frequency ranges are from 45 Hz to 300 Hz.
6. Crossover Control SwitchThis switch is used to select high pass, low pass or flat (no crossover) operation for the amplifier speaker outputs.
7. High Pass Crossover ControlThe control is used to select the High pass filter frequency. The frequency ranges are from 45 Hz to 300Hz.
8. Bass Boost Remote Input JackUse to plug in the remote bass controller. (Optional ) see back
9. High Level InputTo be used when no RCA’s are available. Use the provided loom to connect to closest speakers. The loom connector will only fit one way around. Once plugged in you should connect the wires as below:
Left Positive - White Right Positive - Grey Left Negative - White / Black Right Negative - Grey / Black
10. Indicator LEDWhen the amplifier is operating correctly the LED will show as green. When the amplifier is in protection mode the LED will show as red.
11. Power ConnectionsPower connections. See Connections section for details on correct connections.
12. FusesPlease ensure the following fuse rating is used when replacing fuses: 15 amp x 2
13. Speaker Terminal OutputFor connection to the speakers. See Application section for wiring examples.
P o w e r P r o t e c t
S P - S P - S P + S P +
R
I n p u t
L + R + L - R -
R
L L
H i L e v e l L i n e O u t L i n e I n
O F F O N
S u b s o n i c P h a s e L P F G a i n
M i n M a x 3 5 H z 2 5 0 H z 0 ° 1 8 0 ° 8 0 H z 1 6 H z 2 4 d B 0 d B
R e m o t e B a s s B o o s t
ED72500 ED71200
ED71200
ED7800
ED7800
ED72500
MONOBLOCK AMPLIFIER 1 X 1250 WATTS RMS
ED71600
ED71600
4 CHANNEL AMPLIFIER 4 X 200 WATTS RMS
ED7400
ED7400 2 CHANNEL AMPLIFIER 2 X 100 WATTS RMS
MONOBLOCK AMPLIFIER 1 X 600 WATTS RMS
4 CHANNEL AMPLIFIER 4 X 100 WATTS RMS
4 x 35 AMP
3 x 35 AMP
INPUT
2 x 15 AMP
2 x 25 AMP
2 x 20 AMP
1 2 57 83 46910
11 12 13
123 5 7 8649
1011 12
12 3 4 95
6 714
8 10
11 12 13
11 2 3 4 5 6 89
10 11 1213
7234 5 67 89
10 1112
13 14
1. Low Level OutputA daisy chain output For connection to another amplifier with a low level input using only a single RCA output from the source (headunit).
2. Low Level InputFor connection to any source (headunit) with a low level output. This is your RCA output from the source (headunit)
3. Gain ControlUsed to match the input signal of the source to the amplifier. See the setup section for more details.
4. Bass Boost SwitchTo provide up to an extra +12 dB of bass boost at 45 Hz. Use this boost to increase bass output from the amplifier.
1. Low Level InputFor connection to any source (headunit) with a low level output. This is your RCA output from the source (headunit).
2. Rear Gain ControlUsed to match the input signal of the source to the amplifier. See the setup section for more details.
3. Rear Crossover ControlThe switch is used to select between low pass / high pass filter or no filter at all on the front channels. The frequency ranges on the low pass filter are from 40 Hz to 300 Hz. The frequency ranges on the high pass filter are from 40 Hz to 300hz.
4. Rear Bass Boost SwitchTo provide up to an extra +12 dB of bass boost at 45 Hz. Use this boost to increase bass output from the amplifier.
5. Front Gain ControlUsed to match the input signal of the source to the amplifier. See the setup section for more details.
6. Front Bass Boost SwitchTo provide up to an extra +12 dB of bass boost at 45 Hz. Use this boost to increase bass output from the amplifier.
7. Front Crossover ControlThe switch is used to select between low pass / high pass filter or no filter at all on the rear channels. The frequency ranges on the low pass filter are from 40 Hz to 300 Hz. The frequency ranges on the high pass filter are from 40 Hz to 300hz.
8. Front Bass Boost Remote Input JackUse to plug in the remote bass controller. (optional)
9. Indicator LEDWhen the amplifier is operating correctly the LED will show as green When the amplifier is in protection mode the LED will show as red.
10. Power ConnectionsPower connections. See Connections section for details on correct connections.
11. FusesPlease ensure the following fuse rating is used when replacing fuses: 25 amp x 2
12. Speaker Terminal OutputFor connection to the speakers. See Application section for wiring examples.
.
Terminals and Controls ED7800
P o w e r P r o t e c t
S P - S P - S P + S P +
R
I n p u t
L + R + L - R -
R
L L
H i L e v e l L i n e O u t L i n e I n
O F F O N
S u b s o n i c P h a s e L P F G a i n
M i n M a x 3 5 H z 2 5 0 H z 0 ° 1 8 0 ° 8 0 H z 1 6 H z 2 4 d B 0 d B
R e m o t e B a s s B o o s t
ED72500 ED71200
ED71200
ED7800
ED7800
ED72500
MONOBLOCK AMPLIFIER 1 X 1250 WATTS RMS
ED71600
ED71600
4 CHANNEL AMPLIFIER 4 X 200 WATTS RMS
ED7400
ED7400 2 CHANNEL AMPLIFIER 2 X 100 WATTS RMS
MONOBLOCK AMPLIFIER 1 X 600 WATTS RMS
4 CHANNEL AMPLIFIER 4 X 100 WATTS RMS
4 x 35 AMP
3 x 35 AMP
INPUT
2 x 15 AMP
2 x 25 AMP
2 x 20 AMP
1 2 57 83 46910
11 12 13
123 5 7 8649
1011 12
12 3 4 95
6 714
8 10
11 12 13
11 2 3 4 5 6 89
10 11 1213
7234 5 67 89
10 1112
13 14
1. Low Level InputFor connection to any source (headunit) with a low level output. This is your RCA output from the source (headunit).
2. High Level InputTo be used when no RCA’s are available. Use the provided loom to connect to closest speakers. The loom connector will only fit one way around. Once plugged in you should connect the wires as below:
Front Speakers
Left Positive - Green Right Positive - PurpleLeft Negative - Green / Black Right Negative - Purple / Black
Rear Speakers
Left Positive - White Right Positive - GreyLeft Negative - White / Black Left Negative - Grey / Black
3. Front Gain ControlUsed to match the input signal of the source to the amplifier. See the setup section for more details.
4. Front Crossover ControlThe switch is used to select between low pass / high pass filter or no filter at all on the front channels. The frequency ranges on the low pass filter are from 45 Hz to 300 Hz. The frequency ranges on the high pass filter are from 45 Hz to 300 Hz.
5. Front Bass Boost SwitchTo provide up to an extra +12 dB of bass boost at 45 Hz. Use this boost to increase bass output from the amplifier.
6. Rear Gain ControlUsed to match the input signal of the source to the amplifier. See the setup section for more details.
7. Rear Bass Boost SwitchTo provide up to an extra +12 dB of bass boost at 45 Hz. Use this boost to increase bass output from the amplifier.
8. Rear Crossover Control SwitchThe switch is used to select between low pass / high pass filter or no filter at all on the rear channels. The frequency ranges on the low pass filter are from 45 Hz to 300 Hz. The frequency ranges on the high pass filter are from 45 Hz to 300 Hz.
9. Front Bass Boost Remote Input JackUse to plug in the remote bass controller. (optional)
10. Indicator LEDWhen the amplifier is operating correctly the LED will show as green. When the amplifier is in protection mode the LED will show as red.
11. Power ConnectionsPower connections. See Connections section for details on correct connections.
12. FusesPlease ensure the following fuse rating is used when replacing fuses: 35 amp x 3
13. Speaker Terminal OutputFor connection to the speakers. See Application section for wiring examples.
14. Input Mode Select SwitchAllows 4 channels to be driven from a single pair of RCA leads
Terminals and Controls ED71600
P o w e r P r o t e c t
S P - S P - S P + S P +
R
I n p u t
L + R + L - R -
R
L L
H i L e v e l L i n e O u t L i n e I n
O F F O N
S u b s o n i c P h a s e L P F G a i n
M i n M a x 3 5 H z 2 5 0 H z 0 ° 1 8 0 ° 8 0 H z 1 6 H z 2 4 d B 0 d B
R e m o t e B a s s B o o s t
ED72500 ED71200
ED71200
ED7800
ED7800
ED72500
MONOBLOCK AMPLIFIER 1 X 1250 WATTS RMS
ED71600
ED71600
4 CHANNEL AMPLIFIER 4 X 200 WATTS RMS
ED7400
ED7400 2 CHANNEL AMPLIFIER 2 X 100 WATTS RMS
MONOBLOCK AMPLIFIER 1 X 600 WATTS RMS
4 CHANNEL AMPLIFIER 4 X 100 WATTS RMS
4 x 35 AMP
3 x 35 AMP
INPUT
2 x 15 AMP
2 x 25 AMP
2 x 20 AMP
1 2 57 83 46910
11 12 13
123 5 7 8649
1011 12
12 3 4 95
6 714
8 10
11 12 13
11 2 3 4 5 6 89
10 11 1213
7234 5 67 89
10 1112
13 14
1. Low Level InputFor connection to any source (head unit) with a low level output. This is your RCA output from the source (headunit).
2. High Level InputTo be used when no RCA’s are available. Use the provided loom to connect to closest speakers. The loom connector will only fit one way around. Once plugged in you should connect the wires as below:
Left Positive - Brown Right Positive - Black Left Negative - Blue Right Negative - Green
3. Gain ControlUsed to match the input signal of the source to the amplifier. See the setup section for more details.
4. Low Pass Filter ControlLow pass frequency control. The frequency ranges from 35 Hz to 250 Hz.
5. Phase ControlCan be used to alter the phase of the subwoofer from 0 - 180 degrees.IE: the speaker output can be In phase or out of phase with the other speakers in the vehicle. For best results rotate the dial between the two settings to determine the best sound.
6. Subsonic Filter ControlThis is used to filter out unwanted amplifier output to the subwoofer. Effectively this will filter out all the frequencies up to the crossover point set with the control. The range is from 16 Hz to 80 Hz.Frequencies of 80 Hz and below cause the subwoofer to work hard, some subwoofers can easily be damaged when playing very low frequencies. Using the subsonic filter allows less distortion, delivers frequencies better suited to the subwoofer prolonging its life.
7. Subsonic Filter SwitchUsed to turn the filter on or off.
8. Bass Boost SwitchTo provide up to an extra +18 dB of bass boost at 45 Hz. Use this boost to increase bass output from the amplifier.
9. Bass Remote Input JackUse to plug in the remote bass controller. 10. Indicator LEDWhen the amplifier is operating correctly the LED will show as greeb. When the amplifier is in protection mode the LED will show as red.
11. FusesPlease ensure the following fuse rating is used when replacing fuses:20 amp x 2
12. Speaker Terminal OutputFor connection to the speakers. See Application section for wiring examples.
13. Power ConnectionsPower connections. See Connections section for details on correct connections.
14. Low Level OutputDaisy chain RCA connection to allow easy addition of another amplifier.
Terminals and Controls ED71200
P o w e r P r o t e c t
S P - S P - S P + S P +
R
I n p u t
L + R + L - R -
R
L L
H i L e v e l L i n e O u t L i n e I n
O F F O N
S u b s o n i c P h a s e L P F G a i n
M i n M a x 3 5 H z 2 5 0 H z 0 ° 1 8 0 ° 8 0 H z 1 6 H z 2 4 d B 0 d B
R e m o t e B a s s B o o s t
ED72500 ED71200
ED71200
ED7800
ED7800
ED72500
MONOBLOCK AMPLIFIER 1 X 1250 WATTS RMS
ED71600
ED71600
4 CHANNEL AMPLIFIER 4 X 200 WATTS RMS
ED7400
ED7400 2 CHANNEL AMPLIFIER 2 X 100 WATTS RMS
MONOBLOCK AMPLIFIER 1 X 600 WATTS RMS
4 CHANNEL AMPLIFIER 4 X 100 WATTS RMS
4 x 35 AMP
3 x 35 AMP
INPUT
2 x 15 AMP
2 x 25 AMP
2 x 20 AMP
1 2 57 83 46910
11 12 13
123 5 7 8649
1011 12
12 3 4 95
6 714
8 10
11 12 13
11 2 3 4 5 6 89
10 11 1213
7234 5 67 89
10 1112
13 14
1. Low Level Input
For connection to any source (head unit) with a low level output. This is your RCA output from the source (headunit).
2. Gain ControlUsed to match the input signal of the source to the amplifier. See the setup section for more details.
3. Low Pass Filter ControlLow pass frequency control. The frequency ranges from 40 Hz to 250 Hz.
4. Phase ControlCan be used to alter the phase of the subwoofer from 0 - 180 degrees.IE: the speaker output can be Inphase or out of phase with the other speakers in the vehicle. For best results flick between the two settings to determine the best results.
5. Subsonic Filter ControlThis is used to filter out unwanted amplifier output to the subwoofer. Effectively this will filter out all the frequencies up to the crossover point set with the control. The range is from 15 Hz to
50 Hz.Frequencies of 80 Hz and below cause the subwoofer to work hard, some subwoofers cane easily be damaged when playing very low frequencies. Using the subsonic filter allows less distortion, delivers frequencies better suited to the subwoofer prolonging its life.
6. Subsonic Filter SwitchUsed to turn the filter on or off.
7. Bass Boost control To provide up to an extra +18 dB of bass boost at 45 Hz. Use this boost to increase bass output from the amplifier.
8. Bass Remote Input JackUse to plug in the remote bass controller. 9. Indicator LEDWhen the amplifier is operating correctly the LED will show as green. When the amplifier is in protection mode the LED will show as red.
10. FusesPlease ensure the following fuse rating is used when replacing fuses:35 amp x 4
11. Speaker Terminal OutputFor connection to the speakers. See Application section for wiring examples.
12. Power ConnectionsPower connections. See Connections section for details on correct connections.
13. Low Level OutputDaisy chain RCA connection to allow easy addition of another amplifier.
P o w e r P r o t e c t
S P - S P - S P + S P +
R
I n p u t
L + R + L - R -
R
L L
H i L e v e l L i n e O u t L i n e I n
O F F O N
S u b s o n i c P h a s e L P F G a i n
M i n M a x 3 5 H z 2 5 0 H z 0 ° 1 8 0 ° 8 0 H z 1 6 H z 2 4 d B 0 d B
R e m o t e B a s s B o o s t
ED72500 ED71200
ED71200
ED7800
ED7800
ED72500
MONOBLOCK AMPLIFIER 1 X 1250 WATTS RMS
ED71600
ED71600
4 CHANNEL AMPLIFIER 4 X 200 WATTS RMS
ED7400
ED7400 2 CHANNEL AMPLIFIER 2 X 100 WATTS RMS
MONOBLOCK AMPLIFIER 1 X 600 WATTS RMS
4 CHANNEL AMPLIFIER 4 X 100 WATTS RMS
4 x 35 AMP
3 x 35 AMP
INPUT
2 x 15 AMP
2 x 25 AMP
2 x 20 AMP
1 2 57 83 46910
11 12 13
123 5 7 8649
1011 12
12 3 4 95
6 714
8 10
11 12 13
11 2 3 4 5 6 89
10 11 1213
7234 5 67 89
10 1112
13 14
Terminals and Controls ED72500
Troubleshooting
● Before removing the amplifier, refer to the list below and follow the suggested procedures. ● Always test the speakers and confirm that they are wired correctly first. ● If in any doubt get help from a qualified auto electrician.
Amplifier Will Not Power Up● Check for good ground connections. Ensure Ground cable is connected directly to bare metal and not a painted surface. ● Using a multimeter check that remote terminal has at least 10V DC.● Using a multi meter check that there is battery voltage on the positive terminal.● Check all fuses.● Check that the protection light is not illuminated. If it is lit, shut off the amplifier for thirty seconds and then turn it back on.
Protection LED Illuminates When Amplifier Is Powered Up● Check for shorts on all speakers wires. (IE no speaker wires should be joined together and no speaker wires should be touching the cars chassis)● The amplifier is designed to shut down automatically when the units temperature goes above 80 degrees. If the amplifier feels very hot then this may be the reason for the amplifier not starting.● Remove the speaker wires and reset the amplifier. If the protection LED still comes on then the amplifier is faulty. This damage may have been caused by either failure to follow these setup guidelines or abuse.
Amplifier Gets Very Hot● Check the minimum speaker impedance for the amplifier is correct. ● Check for shorts on all speakers wires. (IE no speaker wires should be joined together and no speaker wires should be touching the cars chassis)● Check that there is good airflow around the amplifier. In some applications an external fan may be required.
Blown Fuse(s) ● Check both positive supply and ground for shorts.● Check that the positive wire is connected to the positive terminal on the amplifier.● Check that the negative wire is connected to the ground terminal on the amplifier. ● Ensure that the correct rated fuse is fitted
Distorted Sound● Check the gain control is not set at too high a level. If the speakers sound distorted turn the down the gain until the sound is clear. ● Check that all crossover frequencies are correct. See setup section for more details. ● Check for shorts on all speaker wires. ● Check all speakers are wired correctly. With the correct polarity being observed on each connection.
Set Up Section
To correctly set the gain control of the amplifier to match that of the source (headunit) use the following setup routine:
Turn the gain control to minimum on the amplifier.Ensure the bass boost is set to 0 dB.On the headunit set all crossovers to flat and both bass and treble to zero.Turn up the source (headunit) to approx 3/4 volume.Very slowly turn up the gain on the amplifier until distortion can be heard in any of the speakers or until the volume reaches an uncomfortable listening level when this is reached turn down the gain control slightly.
The gain control is now set.
The setting of the crossover will depend on what kind of speaker you are installing.
For a subwoofer it is recommended that the crossover is set to Low Pass and the frequency is set to match that of the speakers specifications.
For a pair of full range speakers it is recommend that the crossover is set to Flat. The two frequency controls will then have no effect on the amplifiers output and the speaker will receive a full range signal. However, using the high pass crossovers will allow more control of your speakers. By removing the bass (low frequencies) the speakers can perform at higher volumes with less distortion.
Note: The smaller the speaker, the less bass it can handle. Adjust the crossover to get the most and best sound from your speakers. The easiest was to do this is by limiting the amount of bass you feed them
For a pair of speakers with a passive crossover it is recommended that the crossover is set to High Pass and the frequency is set to match that of the speakers specifications.
Note:
By using the crossovers correctly you will not only lengthen the life of your speakers but you will also get better performance from them. To optimise your setup seek the advice of a professional installation engineer or visit your local EDGE audio dealer.
PowerProtect
SP- SP- SP+SP+
ED71200
ED7800
MONOBLOCK AMPLIFIER 1 X 600 WATTS RMS
4 CHANNEL AMPLIFIER 4 X 100 WATTS RMS
2 x 25 AMP
2 x 20 AMP
ED74002 CHANNEL AMPLIFIER 2 X 100 WATTS RMS
2 x 15 AMP
ED74002 CHANNEL AMPLIFIER 2 X 100 WATTS RMS
2 x 15 AMP
ED78004 CHANNEL AMPLIFIER 4 X 100 WATTS RMS
2 x 25 AMP
PowerProtect
SP- SP- SP+SP+
ED71200MONOBLOCK AMPLIFIER 1 X 600 WATTS RMS
2 x 20 AMP
PowerProtect
SP- SP- SP+SP+
ED71200MONOBLOCK AMPLIFIER 1 X 600 WATTS RMS
2 x 20 AMP
+ - + -
+ -
+ -
+ - + -
+ - + -
+ - + -
+-
+-+-
+-
+- +-
+-
PowerProtect
SP- SP- SP+SP+
ED71200
ED7800
MONOBLOCK AMPLIFIER 1 X 600 WATTS RMS
4 CHANNEL AMPLIFIER 4 X 100 WATTS RMS
2 x 25 AMP
2 x 20 AMP
ED74002 CHANNEL AMPLIFIER 2 X 100 WATTS RMS
2 x 15 AMP
ED74002 CHANNEL AMPLIFIER 2 X 100 WATTS RMS
2 x 15 AMP
ED78004 CHANNEL AMPLIFIER 4 X 100 WATTS RMS
2 x 25 AMP
PowerProtect
SP- SP- SP+SP+
ED71200MONOBLOCK AMPLIFIER 1 X 600 WATTS RMS
2 x 20 AMP
PowerProtect
SP- SP- SP+SP+
ED71200MONOBLOCK AMPLIFIER 1 X 600 WATTS RMS
2 x 20 AMP
+ - + -
+ -
+ -
+ - + -
+ - + -
+ - + -
+-
+-+-
+-
+- +-
+-
ED7400 in 2 channel configuration connected to a pair of ED209 speakers
ED7400 in bridged configuration connected to an ED512 subwoofer
Minimum impedance 2 Ohms
Minimum impedance 4 Ohms
ED7800 / 71600 in 4 channel configuration connected to 2 pairs of ED209 speakers
ED7800 / 71600 in 3 channel configuration connected to a pair of ED209 speakers and an ED512 subwoofer
Minimum impedance 2 Ohms
Minimum impedance 2 Ohms
Minimum impedance 2 Ohms
Minimum impedance 4 Ohms
Applications
PowerProtect
SP- SP- SP+SP+
ED71200
ED7800
MONOBLOCK AMPLIFIER 1 X 600 WATTS RMS
4 CHANNEL AMPLIFIER 4 X 100 WATTS RMS
2 x 25 AMP
2 x 20 AMP
ED74002 CHANNEL AMPLIFIER 2 X 100 WATTS RMS
2 x 15 AMP
ED74002 CHANNEL AMPLIFIER 2 X 100 WATTS RMS
2 x 15 AMP
ED78004 CHANNEL AMPLIFIER 4 X 100 WATTS RMS
2 x 25 AMP
PowerProtect
SP- SP- SP+SP+
ED71200MONOBLOCK AMPLIFIER 1 X 600 WATTS RMS
2 x 20 AMP
PowerProtect
SP- SP- SP+SP+
ED71200MONOBLOCK AMPLIFIER 1 X 600 WATTS RMS
2 x 20 AMP
+ - + -
+ -
+ -
+ - + -
+ - + -
+ - + -
+-
+-+-
+-
+- +-
+-
PowerProtect
SP- SP- SP+SP+
ED71200
ED7800
MONOBLOCK AMPLIFIER 1 X 600 WATTS RMS
4 CHANNEL AMPLIFIER 4 X 100 WATTS RMS
2 x 25 AMP
2 x 20 AMP
ED74002 CHANNEL AMPLIFIER 2 X 100 WATTS RMS
2 x 15 AMP
ED74002 CHANNEL AMPLIFIER 2 X 100 WATTS RMS
2 x 15 AMP
ED78004 CHANNEL AMPLIFIER 4 X 100 WATTS RMS
2 x 25 AMP
PowerProtect
SP- SP- SP+SP+
ED71200MONOBLOCK AMPLIFIER 1 X 600 WATTS RMS
2 x 20 AMP
PowerProtect
SP- SP- SP+SP+
ED71200MONOBLOCK AMPLIFIER 1 X 600 WATTS RMS
2 x 20 AMP
+ - + -
+ -
+ -
+ - + -
+ - + -
+ - + -
+-
+-+-
+-
+- +-
+-
ED71200 connected in mono configuration to an ED512 subwoofer at 4 ohms
Minimum impedance 1 Ohms
ED71200 connected in mono configuration a pair of ED512 subwoofers at 2 ohms
Minimum Impedance 1 Ohms
ED71200 connected in mono configuration to 4 ED512 subwoofers at 1 ohms
Minimum Impedance 1 Ohms
PowerProtect
SP- SP- SP+SP+
ED71200
ED7800
MONOBLOCK AMPLIFIER 1 X 600 WATTS RMS
4 CHANNEL AMPLIFIER 4 X 100 WATTS RMS
2 x 25 AMP
2 x 20 AMP
ED74002 CHANNEL AMPLIFIER 2 X 100 WATTS RMS
2 x 15 AMP
ED74002 CHANNEL AMPLIFIER 2 X 100 WATTS RMS
2 x 15 AMP
ED78004 CHANNEL AMPLIFIER 4 X 100 WATTS RMS
2 x 25 AMP
PowerProtect
SP- SP- SP+SP+
ED71200MONOBLOCK AMPLIFIER 1 X 600 WATTS RMS
2 x 20 AMP
PowerProtect
SP- SP- SP+SP+
ED71200MONOBLOCK AMPLIFIER 1 X 600 WATTS RMS
2 x 20 AMP
+ - + -
+ -
+ -
+ - + -
+ - + -
+ - + -
+-
+-+-
+-
+- +-
+-
ED72500MONOBLOCK AMPLIFIER 1 X 1250 WATTS RMS
4 x 35 AMP
ED72500MONOBLOCK AMPLIFIER 1 X 1250 WATTS RMS
4 x 35 AMP
ED72500MONOBLOCK AMPLIFIER 1 X 1250 WATTS RMS
4 x 35 AMP
+ -
+ -+ -
+ -
+ - + -
+ -
ED72500connected in mono configuration to an
ED512 subwoofer at 4 ohms
Minimum impedance 1 Ohms
ED72500connected in mono
configuration a pair of ED512
subwoofers at 2 ohms
Minimum Impedance 1 Ohms
ED72500connected in mono
configuration to 4 ED512 subwoofers
at 1 ohms
Minimum Impedance 1 Ohms